Young Jin Electronics Co PS 300R User Manual

OPERATIN G MANUAL

CAR PARKING SENSOR WITH WIRELESS DISPLAY

UNIT

MODEL : YPS-300M

The Ultrasonic Car Parking Safety Device has been engineered with the highest
technology and equipped with the most advanced wireless features.
The system helps the driver to be in better control when reversing.
When the car appr oaches t oo cl ose to an object in the detection zone, an al ar m
sounds, increasing the intensity in proportional to distance from the object,
simultaneously displaying the direction of right or left side and distance. This
allows the driver to have better control when parking in tight spaces and greatly
improving safety and judgments.

OPERATING METHODS

•

When in reverse, the system sounds a beep and senses the first detection zone

(within1.6m(5.0ft) distance), second zone at 1.0m(3.0ft) and the third zone at

0.6m(2.0ft) the alarm sounds progressively.
From 0.4m(1.0ft) the alarm sounds continually indicating the driver to stop. For the
driver with hearing p r oblems the displays shows 0.0m(0.0ft) the ac tual distance is

0.1m( 0.5ft). Th is system als o indicates the closest sid e to an object left or r i gh t.

FEATURES

•

Compact and unique display unit

•

Built-in buzzers both display and main body

•

4 stage audio and visual LCD display from 1.6 meters to 0.4meters

•

2 ultrasonic sensors installed on or under the rear bumper

•

Display's distance, direction and sound.

•

Aids reversing in all weathers.

•

Eas y Ins tallation on any v ehic le.

•

Especially design with wireless LCD display).

•

No scratches.

•

SPECIFICATIONS

•

Detection : Ultrasonic sensor
lnput power : 9VOLTS TO 16VOLTS DC
Operati ng tem perat ure : - 20°C ~ 60°C
Length of wiring :2 Meters(Sensor), 4 Meters( Main module& monitor power wire )
DETECTION RANGE DISPLAY : 0.4METERS TO 1.6 METERS
Current consumption : 30mA( Main module ), 85mA( Monitor )
Dimension : 70(W) X 93(L) X 33(H) Main control module
66(w) X 62(L) X 40(H) Wireless monitor
Weight (with blister packing) : 357g

OPERATING DISTANCE DISPLAY

♦

STE
P
1 OVER 20 0 CM N/A

2
3
4
5
6

♦

DISTANCE(CM)BEEP SOUND MONITOR

DISPLAY

N/A “ 2.0 ” – “

160-2 00 CM
100-1 60 CM SLOW LY BEEPING

60-100 CM NORMALLY BEEPING
40 – 60 CM QUICKLY BEEPING

WI THIN 40 CM CONTINUOUS

BEEPING

1.6”DISPLAY
“ 1.6 “ – “ 1.0 “

DISPLAY
“ 0.6 “ – “ 1.0 ”
DISPLAY
“0.4 “ – “ 0.6 “
DISPLAY
“ 0.4 “ & “ 0 “
DISPLAY
SEQUENTLY

PROGRAMMING MODE

“

“ FLASHING

••••

REMARK(

MODE )
REVERSING
MODE

DETECTING THE
OBJECT

1ST ALARM
(1st NOTICE MODE)

2ND ALARM

ND

NOTICE M ODE)

(2
3RD ALARM
( WARNING M ODE)
STOPPING THE
CAR
DRIVING

A. BEEP SOUNDING ON/O FF IN THE MONITOR
The beep sounding will be OFF with one beep sounding if you press the switch for 2
seconds in the back of the monitor by using a small screw driver and the beeping
sound will be ON with one beep sounding if you repeat above process.

B. REMOTE CODE PROGRAMMING IN THE MONITIOR
Turn on the power( plug-in the connector) in the condition of pressing the switch in
the monitor.
You will hear one beep sounding in the monitor and then turn on the power( plug-in
the connector) in the m ain control module. You will hear one beep sounding to
confirm code programming.

C. HOW TO SWITCH FROM METERS TO FEET
Follow instructions in step one, depressing the switch for 6 seconds and the display
will toggle between meters and feet display.

NOTE

1. The YPS-300M is operated onl y when reversing the car.

2. Pl ease k eep clean i ng the ultrasonic sensor for corr ect operation.

3. The system c annot be often operat ed in the small object su ch as wire, rope,
sponge or textile etc.

Th is device compl ies with part 15 of th e FCC Rules. Operati on is subject t o the foll ow ing
two condi t ions: (1) This d evice may no t cause harmful interferen ce, and ( 2) t his d evice
must accept any i nterference receiv ed, i ncluding interf erence that may cause undesired
operation.

Caution : Any changes or modifications in construction of this device which are not
expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.