QuickStart Guide
YoSmart Remote Controller
Model: KT-LR-U01B
Good Choice J
The Remote controller enables you to control the
controller by hand.
Getting Started
Correctly insert disk shape battery.
Description of
remote buttons’ function：
Shown in picture below
LED
All available colors
，
Turning lights on and off
，
To modify brightness of LED lights（only work with a single color
）
Number button functionality:
1. While linking choose the sections you want to link，or the sections you want to control simultaneously。
Selecting ALL will link all the sections.
2. Also used to set time for light to remain on, the maximum time is 9.9 hours.
Used to set how long you want the light to stay on.
Instructions：
1. Press Duration, then set however long you want with the number buttons, (maximum time is 9.9 hours,
you must insert numbers after the decimal, not putting a time will be understood as maximum duration)
2. When the LED light is on, it will turn off when time is reached. If the LED light is turned off, timer
will start the next time it is turned on, until time is reached.
Set a timer
Instructions：
1. Choose the mode LED lights
2. Press the Timer button, use the number buttons to insert time (maximum 9.99 hours, be sure to insert two numbers
after the decimal point. For example if the time is 6 hours then put 6.00. ) When time is reached, the mode will
return to standard mode.
3. If the LED light is turned off while setting time, when time is reached, LED will return to the mode before it was
turned off.
Starts the flashing
Stop the flashing.
Changes the way that LED lights flashes.
Increases the speed in which LED lights flashes.
Decreases the speed in which the LED lights flashes.
LINK
button：
1. LINK：hold button 4-8S，enter LINK process，green LED flashes，if successful LINK with device the green
LED flash will go away，if fail to LINK within 4 minutes，will be forced out of LINK，LED light goes out.
2. UNLINK：hold for 10S，enters UNLINK process，red LED flashes, if successful UNLINK with device the red LED
flash will go away，if fail to LINK within 4 minutes，will be forced out of LINK，LED light goes out.
3. While LINK or UNLINK is in process you can press it again to cancel.
Support
Visit: http://www.YoSmart.com/support for complete manual, online tech support and latest product documents.
FCC Caution: Anychanges ormodifications not expressly approved bythe partyresponsible
forcompliancecouldvoidthe user's authoritytooperate this equipment.
This devicecomplieswithPart15 of theFCC Rules.Operationissubject tothefollowingtwo
conditions:(1)This devicemaynotcause harmfulinterference,and(2)thisdevicemust accept
anyinterferencereceived,includinginterference thatmaycauseundesiredoperation.
NOTE:This equipment has been testedandfound to complywith thelimitsfor a ClassB
digitaldevice,pursuant toPart15 of theFCC Rules.
Theselimits are designedto providereasonable protectionagainstharmfulinterferencein a
residentialinstallation.This equipment generates, uses and canradiateradiofrequency
energyand,if notinstalledandusedin accordancewith theinstructions,maycause harmful
interferencetoradiocommunications.
However,thereis noguaranteethatinterferencewillnot occurin a particularinstallation.
Ifthisequipmentdoescauseharmfulinterferencetoradioortelevisionreception,whichcanbe
determinedbyturningthe equipment off and on, the useris encouraged to trytocorrect the
interference byone ormore of the followingmeasures:
FCC RF RadiationExposureStatement:
This equipmentcomplieswithFCCradiationexposurelimitssetforthfor an uncontrolled
environmentEndusersmustfollowthespecific operatinginstructionsforsatisfying RF
exposurecompliance.This transmittermust not be collocatedor operatinginconjunctionwith
anyother antenna or transmitter.
The devicehas beenevaluatedtomeet general RF exposurerequirement.Thedevicecanbe
usedinportableexposureconditionwithoutrestriction.
Loading...