Yorkville Sound NX20, NX12 User Manual

w w w . y o r k v i l l e . c o m

Yorkville Sound

550 Granite Court
Pickering, Ontario
L1W-3Y8 CANADA

Canada

Voice: [phone]
Fax: [phone]

Yorkville Sound Inc.

4625 Witmer Industrial Estate
Niagara Falls, New York
14305 USA

U.S.A.

Voice: [phone]
Fax: [phone]

Printed in Canada

Yorkville NX Flyware

Manual-Owners-NXF100-1v4.pdf

The NX12, NX20 and NX520p are a few of the many Yorkville speaker enclo­sures equipped with flying hardware for overhead suspension applications. These
hardware kits have been specifically designed to expand the enclosure’s already
advanced mounting capabilities.

IMPORTANT!! THE RIGGING OF LOUDSPEAKER SYSTEMS IS AN EXTREMELY SERIOUS MATTER.
OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, INCLUDING (BUT NOT LIMITED TO)
CALCULATING WORKING LOAD LIMITS, HARDWARE INSTALLATION, AND PERIODIC SAFETY
INSPECTION OF ALL HARDWARE AND CABINETRY. IF YOU LACK THESE QUALIFICATIONS,
DO NOT ATTEMPT THE INSTALLATION YOURSELF, BUT INSTEAD USE A PROFESSIONAL
STRUCTURAL RIGGER. IMPROPER INSTALLATION CAN RESULT IN BODILY INJURY OR DEATH.
CONSULT A STRUCTURAL ENGINEER TO CALCULATE ADDED LOADS FOR A BUILDING.
STRUCTURAL REINFORCEMENT MAY BE NECESSARY TO INSURE A SAFE INSTALLATION.

The NXF100 System

The NXF100 installation system has been developed to expand the NX12, NX20
and the NX520p enclosure’s capabilities to be mounted in more ways than a stan­dard shackle and cables allow. It’s a unique U-bracket system that attaches to the
NX enclosures’ integrated flypoints. Multiple flypoints on the brackets ensure the rig
can be flown at virtually any angle. It can be secured to the truss or roofing system
with almost any typical flyware currently available. The NXF100 is easily mounted to
the top of the enclosure as well as the bottom standmount adapter. Additionally, the
cabinet can be angled up to 45 degrees across the horizon­tal plane within the NXF100 housing.

Wall Mounting (NXF105)

For wall mounting applications,
the NXF100 can be attached to
an optional NXF105 wall-mount
bracket. This bracket enables the
NX enclosure to achieve angles up
to 30 degrees forward while being
securely attached to a wall or pillar.

Flying Arrays (NXF110)

Using the optional NXF110 Flying
Array Adapter perfect 60 degree

spacing between multiple enclosures,
in a circular array is achieved. The NXF110 joins
the NXF100 U-Brackets together safely and securely
and is extremely simple to install for flying two enclosure or
up to six cabinets in the circular arrays.

NX Flyware System Components

NXF100 - Steel U-Bracket and flying assembly
NXF105 - Wall Mounting Bracket ( - to attach NXF100 assembly to wall or piller)
NXF110 - Array Link Assembly ( - to properly array and space out multiple NXF100
Flying assemblies)
The ideal center cluster array is easily assembled using three NXF100 U brackets,
and four NXF110s. (Shackles and cables not included.)

1

w w w . y o r k v i l l e . c o m

Yorkville Sound

550 Granite Court
Pickering, Ontario
L1W-3Y8 CANADA

Canada

Voice: [phone]
Fax: [phone]

Yorkville Sound Inc.

4625 Witmer Industrial Estate
Niagara Falls, New York
14305 USA

U.S.A.

Voice: [phone]
Fax: [phone]

Printed in Canada

Yorkville NX Flyware

Step 1

Remove the existing top 2 flyware bolts
(top shown)

Step 2

Remove the bottom 3 stand adapter bolts as shown.

Save bolts, you will be using them again.

(bottom shown)

Step 3

Align the U-Bracket on cabinet (the NXF100 comes
pre assembled). This will enable you to access the
bolts on the top of the cabinet.
(top shown)

Step 4

Tighten the bolts to the cabinet. That’s it, you’re ready

to fly the cabinet in your rig.

(bottom shown)

NXF105

Pictured assembled on the
NXF100 Flyware bracket

2