Yorkville CU15FH Owner's Manual

w w w . y o r k v i l l e . c o m

Yorkville Sound

550 Granite Court
Pickering, Ontario
L1W-3Y8 CANADA

Canada

Voice: [phone]
Fax: [phone]

Yorkville Sound Inc.

4625 Witmer Industrial Estate
Niagara Falls, New York
14305 USA

U.S.A.

Voice: [phone]
Fax: [phone]

Printed in Canada

Flyware Bracket System

Manual-Owners-CU15FH-1v0.pdf

Yorkville CU15FH

The CU15 is one of the many Yorkville speaker enclosures equipped with flying
hardware for overhead suspension applications. This hardware kit has been specifi­cally designed to expand the enclosure’s already advanced mounting capabilities.

IMPORTANT!! The rigging of loudspeaker systems is an extremely serious matter. Overhead rigging
requires extensive experience, including (but not limited to) calculating working load limits, hardware instal­lation, and periodic safety inspection of all hardware and cabinetry. If you lack these qualifications, do not
attempt the installation yourself, but instead use a professional structural rigger. Improper installation can
result in bodily injury or death. Consult a structural engineer to calculate added loads upon the building.
Structural reinforcement may be necessary to insure a safe installation.

The CU15FH System

The CU15FH installation system has been developed to expand
the versatility and simplicity of installing CU15 enclosures in
multi-box arrays. The CU15FH kit allows enclosures to
be mounted in two or more cabinet arrays with greater
ease than employing individual three-point hangs for
each cabinet. (An arduous chore when attempting
to install clusters of loudspeakers using standard
eyebolts, shackles and cables. The CU15FH is
easily mounted strategically to the top and bottom
of the enclosure.

Flying Arrays

A single CU15FH kit allows a pair of CU15 cabi­nets to be clustered in a tight-pack array at their
optimum splay and more can be attached together
for larger clusters (3 or more enclosures).

Z761 x 2 Z762 x 2 Z763 x 4 YS#8920 x 8

Kit Includes

2 Z761 Cross Member Supports
2 Z762 Shackle Cross Members
4 Z763 Support Plates
8 YS#8920 3/8-16 X 2 HH GRD 5 ZP BOLT

1

w w w . y o r k v i l l e . c o m

Yorkville Sound

550 Granite Court
Pickering, Ontario
L1W-3Y8 CANADA

Canada

Voice: [phone]
Fax: [phone]

Yorkville Sound Inc.

4625 Witmer Industrial Estate
Niagara Falls, New York
14305 USA

U.S.A.

Voice: [phone]
Fax: [phone]

Printed in Canada

Flyware Bracket System

Attaching the CU15FH Bracket to CU15 Enclosures

It’s easiest to mount the CU15FH bracket onto the CU15 enclosure prior to flying or mounting.

Step 1

Preparing the CU15 enclosures. Remove the two top and two bottom flyware bolts
closest to the neighboring side of each CU15 enclosure to be conjoined.

FIGURE 1

Step 2

Bracket Assembly. Assemble the CU15FH bracket as shown in the diagram.
Assemble this on a flat surface.

i. Place the two shackle Cross Members side-by-side (as shown in figure 2a).

ii. Mount Cross Member Support ends of the mated Cross Members (as shown

in figure 2b).

iii. Slip the Support Plates into the slots (both ends) created by the mating of the

Shackle Cross Members and the Cross Member Support (as shown in figure 2c).

Tip: it’s easiest to assemble CU15FH Bracket apart from the CU15 enclosure, either on a table or the top
of the enclosure. Use the supplied bolts to align the Support Plates, The Shackle Cross Members and the
Cross Member Support when moving the assembled CU15FH bracket.

FIGURE 2a

FIGURE 2b

FIGURE 2c

2