York YHJD18 User Manual

Download

Page 1

TECHNICAL GUIDE

SPLIT -SYSTEM HEAT PUMPS 13 SEER – R-410A MODELS:

YHJD18 THRU 60

(1.5 THRU 5 NOMINAL TONS - 1PHASE)

Due to continuous product improvement, specifications are subject to change without notice.

Visit us on the web at www.york.com Additional rating information can be found at

www.ahridirectory.org

WARRANTY

Standard 5-year limited parts warranty. 10-year limited compressor warranty.

Extended 10-year limited parts warranty when product is registered online within 90 days of purchase fo r replacement or closing for new home construction.

LISTED

397855-YTG-G-0509

DESCRIPTION

The 13 SEER Series unit is the outdoor part of a versatile climate system. It is designed with a matching indoor coil component from Johnson Controls Unitary Products. Available for typical applications this climate system is supported with accessories and documents to serve specific functions.

FEATURES

• Quality Condenser Coils - The coil is constructed of copper tubing and enhanced aluminum fins for increased efficiency and corrosion protection.

• Protected Compressor - The compressor is internally protected against high pressure, temperature, and externally by a factory installed high pressure switch. This is accomplished by the simultaneous operation of high pressure relief valve and a temperature sensor which protects the compressor if undesirable operating conditions occur. A liquid line filterdrier further protects the compressor.

• Durrable Finish - The cabinet is made of pre-painted steel. The pre-treated galvanized steel provides a better paint to steel bond, which resists corrosion and rust creep. Special primer formulas and matted-textured finish insure less fading when exposed to sunlight.

• Lower Installed Cost - Installation time and costs are reduced by easy power and control wiring connections. Available in sweat connect models only. The unit contains enough refrigerant for matching indoor coils and 15 feet of interconnecting piping. The small base dimension means less space is required on the ground or roof.

• Top D is c h ar g e - The warm air from the top mounted fan is blown up away from the structure and any landscaping. Thi s allows compact location on multi-unit applications.

• Low Operating Sound Level - The upward air flow carries the normal operating noise away from the living area. The rigid top panel effectively isolates any motor sound. Isolator mounted compressor and the rippled fins of the condense r coil muffle the normal fan motor and compressor operating sounds.

• Low Maintenance - Long life permanently lubricated motorbearings need no annual servicing.

• Easy Service Access - Fully exposed refrigerant connec- tions, and a single panel covering the electrical controls make for easy servicing of the unit.

• Secured Service Valves - Secured re-usable service valves are provided on both the liquid and vapor sweat connections for ease of evacuating and charging.

• U.L. and C.U.L. listed - approved for outdoor application.

• Agency Listed - U.L. and C.U.L. listed - approved for o utdoor application. The unit is certified in accordance with the Unitary Small Equipment certification program, which is based on ARI Standard 210/240.

FOR DISTRIBUTION USE ONLY - NOT TO BE USED AT POINT OF RETAIL SALE

Page 2

397855-YTG-G-0509

Physical and Electrical Data

MODEL

YHJD18

S41S1

YHJD24

S41S1

YHJD30

S41S1

YHJD36

S41S1

YHJD42

S41S1

YHJD48

S41S1

YHJD60

S41S2

Unit Supply Voltage 208-230V, 1 60Hz Normal Voltage Range

187 to 252

Minimum Circuit Ampacity 9.6 12.0 15.4 19.6 28.6 30.9 37.4 Max. Overcurrent Device Amps Min. Overcurrent Device Amps

15 20 25 30 50 50 60 15 15 20 20 30 35 40

Compressor Type Recip Recip Recip Recip Scroll Scroll Scroll Compressor Amps

Rated Load 7.12 8.9 11.65 14.72 21.76 23.61 28.8

Locked Rotor 47.0 48.0 60.0 83.0 105.0 150.0 150.0 Crankcase Heater Yes Yes Yes Yes No No No Fan Motor Amps Rated Load 0.70 0.80 0.80 1.5 1.5 1.5 1.5 Fan Diameter Inches 24 24 24 24 24 24 24

Rated HP 1/10 1/8 1/8 1/4 1/4 1/4 1/4 Fan Motor

Nominal RPM 825 1075 1075 850 850 850 850

Nominal CFM 2200 2900 3100 3800 3800 3600 3600

Face Area Sq. Ft. 15.7 18.3 21.0 23.58 23.58 23.58 23.6 Coil

Rows Deep 1 1 1 1 1 2 2

Fin / Inches 22 22 22 22 22 18 18 Liquid Line Set OD (Field Installed) 3/8 3/8 3/8 3/8 3/8 3/8 3/8 Vapor Line Set OD (Field Installed) 3/4 3/4 3/4 3/4 7/8 7/8 7/8

Unit Charge (Lbs. - Oz.)

6 - 5 8 - 7 9 - 12 9 - 15 9 - 12 13 - 9 13 - 6

Charge Per Foot, Oz. .62 .62 .62 .62 .67 .67 0.67 Operating Weight Lbs. 172 184 196 208 208 275 290

1. Rated in accordance with ARI Standard 110, utilization range “A”.

2. Dual element fuses or HACR circuit breaker. Maximum allowable overcurrent protection.

3. Dual element fuses or HACR circuit breaker. Minimum recommended overcurrent protection.

4. The Unit Charge is correct for the outdoor unit, matched indoor coil and 15 feet of refrigerant tubing. For tubing lengths other than 15 feet, add or subtract the amount of refrigerant, using the difference in length multiplied by the per foot value.

All dimensions are in inches. They are subject to change without notice. Certified dimensions will be provided upon request.

Unit

Model

18 28

Dimensions

(Inches)

B C Liquid Vapor

34 34 24 32 34 34 30 36 34 34 36 40 34 34 42 40 34 34

60 40 34 34

1. Including Fan Guard.

Refrigerant Connection

Service Valve Size

3/4”

3/8”

7/8”48 40 34 34

2 Johnson Controls Unitary Products

Page 3

System Charge for Various Matched Systems

Outdoor Unit YHJD18S41S1 YHJD24S41S1 YHJD30S41S1 YHJD36S41S1 YHJD42S41S1 YHJD48S41S1 YHJD60S41S2 Required Orifice or TXV

Factory Charge, lbs-oz 6 - 5 8 - 7 9 - 12 9 - 15 9 - 12 13 - 9 13 - 6

Indoor Coil

2,3

FC/MC/PC/UC18AB 0–––––– FC/MC/PC/UC24AB 4–––––– FC/MC/PC30AB 4–––––– FC/MC/PC32A –0––––– FC/MC/PC35BC –0––––– FC/MC/PC37A – 600––– FC/MC/PC43BC –600––– FC/MC/PC/UC48CD – – – 10 0 – – FC/MC/PC/UC60CD ––––00– FC/MC62D –––––120 HC18A 1–––––– HC30A 100––––– HC36B –0––––– HC42 ––00––– HC60 ––––00– HD24 14–––––– HD36 –2––––– HD48 ––88––– HD60 ––––07– AHP18 0–––––– AHP30 –0––––– AHP36 ––00––– AHP/SHP48 ––––00– AHP/SHP60 –––––0– AHX30 –0––––– AHX36 –600––– AHX42 ––––0–– AHX48 ––––00– AHX60 ––––––0 AV*24 3–––––– AV*36 –600––– AV/SV*48 ––––00– AV/SV*60 –––––0– F4FP24 0–––––– F4FP45 –––00–– F5FP48 ––––00– F4FV60 –––––0–

F5FP60 –––––0– F6FP030 –+ 0––––– F6FP036 –+ 0+ 0–––– F6FP042 – – – + 10 + 0 – – F6FP048 ––––+ 0+ 0– F6FP060 ––––––0

FOOTNOTES:

1. For applications requiring a TXV use 1TVM0 series kit.

2. Systems matched with furnace or air handlers not equipped with blower-off delays may require blower Time Delay Kit 2FD06700224.

3. PC coils cannot be used in downflow or horizontal applications. FC coils cannot be used in horizontal applications.

PROCEDURES:

1. Unit factory charge listed on the unit nameplate includes refrigerant for the cond enser, the smallest evaporator and 15 feet of interconnecting line tubing.

2. Verify the TXV and additional charge required for specific evaporator coil in the system using the above table.

3. Additional charge for the amount of interconnecting line tubing greater than 15 feet at the rate specified in Physical and Electrical Data Table.

4. For TXV matches requiring additional charge, the refrigerant needs to be weighed in for specific coil match and lineset length.

5. Permanently mark the unit nameplate with the total system charge. Total System Charge = Base Charge (as shipped) + adder for evaporator + adder for line set.

1TVM04E1 1TVM04G1 1TVM04G1 1TVM04H1 1TVM04H1 1TVM04J1 1TVM04K1

Additional Charge, Oz

Johnson Controls Unitary Products 3

Page 4

397855-YTG-G-0509

COOLING CAPACITY - With Air Handler Coils

UNIT

MODEL

YHJD18S41S1 YHJD24S41S1 MA08B 17 FC/MC/PC35B 800 23.0 17.5 13.00 11.00

YHJD30S41S1 MA12B 17 FC/MC/PC43B 1000 29.0 23.4 13.00 11.00 YHJD36S41S1

YHJD42S41S1

YHJD48S41S1

YHJD60S41S1 MA20D 24 MC62D 1800 54.0 42.5 13.00 11.00

YHJD18S41S1

YHJD24S41S1

YHJD30S41S1

YHJD36S41S1

YHJD42S41S1

YHJD48S41S1 YHJD60S41S1 MV20D 24 MC62D 1800 54.5 43.0 13.50 11.60

YHJD18S41S1 AV*24 17 – 550 17.0 13.0 14.00 12.00 YHJD24S41S1 AV*36 21 – 725 24.0 17.8 14.50 12.50 YHJD30S41S1 AV*36 21 – 1000 29.0 24.4 14.00 12.00 YHJD36S41S1 AV*36 21 – 1190 35.0 28.2 14.00 12.00 YHJD42S41S1 AV/SV*48 24 – 1385 41.5 31.8 14.25 12.00

YHJD48S41S1

For Notes See Page 5.

AIR HANDLER

MODEL W

MA08B 17 FC/MC/PC18B 600 17.0 12.6 13.00 11.00 MA08B 17 FC/MC/PC24B 600 17.0 12.9 13.50 11.00

MA12B 17 FC/MC/PC43B 1200 35.0 26.8 13.00 11.00 MA14D 24 FC/MC/PC48D 1200 35.0 27.0 13.00 11.00 MA14D 24 FC/MC/PC48D 1400 41.5 31.4 13.00 11.00 MA16C 21 FC/MC/PC48C 1400 41.5 31.4 13.00 11.00 MA14D 24 FC/MC/PC60D 1400 41.0 31.2 13.00 11.00 MA16C 21 FC/MC/PC60C 1400 41.0 31.2 13.00 11.00 MA16C 21 FC/MC/PC60C 1600 47.0 35.6 13.00 11.00 MA20D 24 FC/MC/PC60D 1600 47.0 35.6 13.00 11.00 MA20D 24 MC62D 1600 47.0 35.6 13.00 11.00

13 SEER HP WITH MV - VARIABLE SPEED

MV12B 17 FC/MC/PC18B 600 17.0 12.9 14.00 12.00 MV12B 17 FC/MC/PC24B 600 17.0 13.2 14.00 12.00 MV12B 17 FC/MC/PC35B 800 23.0 17.9 14.00 12.00 MV16C 21 FC/MC/PC35C 800 23.0 17.9 14.00 12.00 MV16C 21 FC/MC/PC35C 1000 29.0 23.6 14.00 12.00 MV12B 17 FC/MC/PC43B 1000 29.0 23.8 14.00 12.00 MV16C 21 FC/MC/PC43C 1000 29.0 24.0 14.00 12.00 MV12B 17 FC/MC/PC43B 1200 35.0 27.0 13.50 11.50 MV16C 21 FC/MC/PC43C 1200 35.0 27.2 13.50 11.50 MV12D 24 FC/MC/PC48D 1150 35.0 26.8 13.50 11.50 MV16C 21 FC/MC/PC48C 1200 35.0 27.4 13.50 11.50 MV20D 24 FC/MC/PC48D 1200 35.0 27.4 13.50 11.50 MV16C 21 FC/MC/PC48C 1400 42.0 31.8 14.00 12.00 MV20D 24 FC/MC/PC48D 1400 42.0 32.0 14.00 12.00 MV20D 24 FC/MC/PC60D 1400 41.5 31.8 14.00 12.00 MV20D 24 FC/MC/PC60D 1600 47.5 36.0 14.00 11.80 MV20D 24 MC62D 1600 47.5 36.0 14.00 12.00

13 SEER HP WITH AV / SV / F*FV - VARIABLE SPEED

AV/SV*48 24 – 1600 47.5 36.2 14.00 11.80 AV/SV*60 24 – 1560 47.5 35.0 14.50 12.00

F4FV060 24 – 1600 47.5 36.2 14.00 11.80

COIL

MODEL

13 SEER HP WITH MA

RATED

CFM

TOTAL SENS.

COOLING

NET MBH

SEER EER

4 Johnson Controls Unitary Products

Page 5

COOLING CAPACITY - With Air Handler Coils (Continued)

UNIT

MODEL

AIR HANDLER

MODEL W

COIL

MODEL

RATED

CFM

TOTAL SENS.

13 SEER HP WITH AHP / SHP / AHX / F*FP

YHJD18S41S1

AHP18 17 – 600 17.0 12.7 13.00 11.00

F4FP024 17 – 600 17.0 12.6 13.00 11.00

AHP30 17 – 800 23.0 17.2 13.00 11.00 AHX30 17 – 820 24.0 18.5 14.50 12.50

YHJD24S41S1

AHX36 21 – 815 24.0 18.9 14.50 12.50 F6FP030 17 – 850 24.0 18.5 14.25 12.00 F6FP036 21 – 855 24.0 18.6 14.50 12.20

AHP36 21 – 1000 29.0 23.2 13.00 11.00

YHJD30S41S1

AHX36 21 – 1005 29.6 24.6 14.30 12.00 F6FP036 21 – 980 29.0 23.4 14.00 12.00

AHP36 21 – 1200 35.0 26.8 13.00 11.00

YHJD36S41S1

AHX36 21 – 1225 35.0 28.4 14.00 12.00 F4FP045 24 – 1200 35.0 26.8 13.00 11.00 F6FP042 21 – 1405 35.0 31.2 14.00 12.00

AHP/SHP48 21 – 1400 41.5 31.4 13.00 11.00

AHX42 21 – 1395 41.5 32.0 14.25 12.00

AHX48 24 – 1445 41.5 32.8 14.25 12.00

YHJD42S41S1

F4FP045 24 – 1400 41.0 31.2 13.00 11.00 F5FP048 24 – 1450 41.0 32.6 13.00 11.00 F6FP042 21 – 1455 41.5 32.6 14.25 12.00 F6FP048 24 – 1380 41.5 32.4 14.00 11.50

AHP/SHP60 24 – 1600 47.0 36.0 14.00 11.50

AHX48 24 – 1660 48.0 36.4 14.50 12.00

YHJD48S41S1

F5FP048 24 – 1700 47.5 36.6 14.00 11.50 F5FP060 24 – 1700 47.5 36.8 14.00 11.50 F6FP048 24 – 1625 48.0 36.4 14.25 12.00

YHJD60S41S1

Rated in accordance with DOE test procedures (Federal Register 12-27-79 and 3-18-88) and ARI Standards 210. Cooling MBH based on 8°F entering air temperature, 50% RH, and rated air flow. EER (Energy Efficiency Ratio) is the total cooling output in BT U’s at 95°F outdoor ambient divided by the total electric power in watt-hours at those conditions. SEER (Seasonal Energy Efficiency Ratio) is the total cooling output in BTU’s during a normal annual usage period for cooling divided by the total electric power input in watt-hours during the same period.

AHX60 24 – 1680 54.5 42.0 13.50 11.50 F6FP060 24 – 1710 56.5 42.0 13.50 11.50

COOLING

NET MBH

SEER EER

1. MC coils available with a factory installed horizontal drain pan. See price pages for specific model number. — = Not applicable.

Johnson Controls Unitary Products 5

Page 6

397855-YTG-G-0509

COOLING CAPACITY - Upflow, Downflow & Horizontal Furnaces and Coils

FURNACE**

UNIT MODEL

YHJD18S41S1

YHJD24S41S1

YHJD30S41S1

YHJD36S41S1

YHJD42S41S1

YHJD48S41S1

YHJD60S41S1 1600 - 2000 21,24 MC62 1800 54.0 42.5 13.00 11.00

1. Requires a 2FD06700224 Blower Time Delay unless a standard furnace is equipped with one. ** Refer to Quick Selection Chart for specific furnace match-up.

CFM RANGE

(Min.-max.)

450 - 750 14,17 FC/MC/PC18 600 17.0 12.6 13.00 11.00 450 - 750 14,17 FC/MC/PC24 600 17.0 12.9 13.50 11.00 450 - 750 14 HC18 600 17.0 12.6 13.00 11.00 450 - 750 14 HC30 600 17.0 12.8 13.00 11.00

450 - 750 14 HD24 600 17.0 13.0 13.50 11.00 600 - 1000 14 FC/MC/PC32 800 23.0 17.5 13.00 11.00 600 - 1000 17,21 FC/MC/PC35 800 23.0 17.5 13.00 11.00 600 - 1000 14 HC30 800 23.0 17.2 13.00 11.00 600 - 1000 17 HC36 800 23.0 17.5 13.00 11.00 600 - 1000 14,17 HD36 800 23.0 16.4 13.00 11.00 800 - 1200 14 FC/MC/PC37 1000 29.0 23.4 13.00 11.00 800 - 1200 17,21 FC/MC/PC43 1000 29.0 23.4 13.00 11.00 800 - 1200 21 HC42 1000 29.0 23.4 13.00 11.00 800 - 1200 21,24 HD48 1000 29.0 23.4 13.00 11.00

1000 - 1400 14 FC/MC/PC37 1200 35.0 26.6 13.00 11.00 1000 - 1400 17,21 FC/MC/PC43 1200 35.0 26.8 13.00 11.00 1000 - 1400 21,24 FC/MC/PC48 1200 35.0 27.0 13.00 11.00 1000 - 1400 21 HC42 1200 35.0 26.8 13.00 11.00 1000 - 1400 21,24 HD48 1200 35.0 26.8 13.00 11.00 1200 - 1600 21,24 FC/MC/PC48 1400 41.5 31.4 13.00 11.00 1200 - 1600 21,24 FC/MC/PC60 1400 41.0 31.2 13.00 11.00 1200 - 1600 21 HC42 1400 41.0 31.2 13.00 11.00 1200 - 1600 24 HC60 1400 41.0 31.2 13.00 11.00 1200 - 1600 21,24 HD60 1400 41.5 31.4 13.00 11.00 1400 - 1800 24 HC60 1600 47.0 35.6 13.00 11.00 1400 - 1800 21,24 HD60 1600 47.0 35.4 13.00 11.00 1400 - 1800 21,24 MC62 1600 47.0 35.6 13.00 11.00

COIL

MODEL

RATED

CFM

TOTAL SENS.

COOLING

NET MBH

SEER

EER

6 Johnson Controls Unitary Products

Page 7

COOLING CAPACITY - With High Efficiency Motor Furnaces

UNIT

MODEL

YHJD18S41S1

YHJD24S41S1

30S41S1

YHJD

For Notes See Page 10.

FURNACE

MODEL

COIL

MODEL

13 SEER HP WITH VARIABLE SPEED FURNACES

Y*(8,L)C*A12 FC/MC/PC18A 14 620 17.6 12.3 14.50 12.30 Y*(8,L)C*B12 FC/MC/PC18B 17 580 17.4 11.9 14.40 12.20

(Y*9C/T*9V)*B12 FC/MC/PC18B 17 610 17.6 12.2 14.60 12.40

Y*(8,L)C*A12 FC/MC/PC24A 14 640 18.0 12.7 14.80 12.50 Y*(8,L)C*B12 FC/MC/PC24B 17 575 17.8 12.2 14.90 12.60

(Y*9C/T*9V)*B12 FC/MC/PC24B 17 610 18.0 12.7 14.90 12.60

Y*(8,L)C*A12 FC/MC/PC30A 14 640 18.0 12.7 14.80 12.50 Y*(8,L)C*B12 FC/MC/PC30B 17 575 17.8 12.2 14.90 12.60

(Y*9C/T*9V)*B12 FC/MC/PC30B 17 610 18.0 12.7 14.90 12.60

Y*(8,L)C*A12 HC18 14 620 17.6 12.3 14.50 12.30 Y*(8,L)C*A12 HC30 14 590 17.6 12.2 14.40 12.20 Y*(8,L)C*A12 HD24 14 640 18.0 12.6 14.90 12.60 Y*(8,L)C*B12 HD24 17 575 17.9 12.2 14.90 12.60

(Y*9C/T*9V)*B12 HD24 17 610 18.0 12.6 15.00 12.70

Y*(8,L)C*A12 UC18A 14 620 17.6 12.4 14.60 12.30 Y*(8,L)C*B12 UC18B 17 580 17.5 12.0 14.60 12.30

(Y*9C/T*9V)*B12 UC18B 17 610 17.7 12.3 14.80 12.40

Y*(8,L)C*A12 UC24A 14 640 18.0 12.8 14.80 12.50 Y*(8,L)C*B12 UC24B 17 575 17.8 12.3 14.90 12.60

(Y*9C/T*9V)*B12 UC24B 17 610 18.0 12.8 14.90 12.60

Y*(8,L)C*A12 UC30A 14 640 18.0 12.8 14.80 12.50 Y*(8,L)C*B12 UC30B 17 575 17.8 12.3 15.00 12.60

(Y*9C/T*9V)*B12 UC30B 17 610 18.0 12.8 15.00 12.60

T*9X*B12 FC/MC/PC35B 17 785 23.4 17.0 14.10 12.25 T*(8,L)X*A12 FC/MC/PC37A 14 840 24.2 17.9 14.30 12.60 T*(8,L)X*B12 FC/MC/PC43B 17 865 24.4 18.2 14.50 12.70

T*9X*B12 FC/MC/PC43B 17 800 24.0 17.5 14.40 12.50 T*(8,L)X*B12 FC/MC/PC35B 17 850 23.8 17.7 14.40 12.45

T*9X*C16 FC/MC/PC35C 21 715 23.2 16.3 14.60 12.20 T*(8,L)X*A12 FC/MC/PC32A 14 800 23.6 17.1 14.10 12.50

Y*(8,L)C*A12 FC/MC/PC32A 14 775 23.4 16.2 14.10 12.50 Y*(8,L)C*B12 FC/MC/PC35B 17 760 23.4 16.3 14.40 12.80

(Y*9C/T*9V)*B12 FC/MC/PC35B 17 815 23.6 16.6 14.10 12.60

Y*(8,L)C*A12 FC/MC/PC37A 14 805 23.8 16.8 14.30 12.70 Y*(8,L)C*B12 FC/MC/PC43B 17 760 23.6 16.4 14.50 12.90

(Y*9C/T*9V)*B12 FC/MC/PC43B 17 800 23.8 16.7 14.40 12.80

Y*(8,L)C*B12 HC36 17 760 23.4 16.1 14.30 12.70

(Y*9C/T*9V)*B12 HC36 17 815 23.6 16.6 14.20 12.60

Y*(8,L)C*A12 HD36 14 805 23.0 16.0 14.00 12.40 Y*(8,L)C*B12 HD36 17 760 23.0 15.5 13.90 12.50 Y*(8,L)C*C16 HD36 21 855 23.6 16.4 14.40 12.90 Y*(8,L)C*C20 HD36 21 750 23.0 15.5 14.30 12.80

(Y*9C/T*9V)*B12 HD36 17 815 23.0 16.0 14.10 12.50 (Y*9C/T*9V)*C16 HD36 21 785 23.2 16.0 14.30 12.70 (Y*9C/T*9V)*C20 HD36 21 760 23.0 15.5 14.20 12.60

T*(8

,L)X*A12

FC/MC/PC37A 14 1105 30.4 24.4 14.40 12.10

T*9X*B12 FC/MC/PC43B 17 1095 30.4 24.4 14.45 12.15 T*(8,L)X*B12 FC/MC/PC43B 17 1125 30.4 24.2 14.40 12.10

Y*(8,L)C*A12 FC/MC/PC37A 14 980 29.4 21.8 13.60 12.30 Y*(8,L)C*B12 FC/MC/PC43B 17 990 29.6 22.2 14.10 12.70

(Y*9C/T*9V)*B12 FC/MC/PC43B 17 1035 29.4 22.0 13.70 12.30

Y*(8,L)C*C16 FC/MC/PC43C 21 990 29.8 22.4 14.50 13.00 Y*(8,L)C*C20 FC/MC/PC43C 21 1000 29.8 22.6 14.60 13.00

RATED

CFM

COOLING

Net MBH

TOTAL SENS.

SEER EER

Johnson Controls Unitary Products 7

Page 8

397855-YTG-G-0509

COOLING CAP ACITY - With High Efficiency Motor Furnaces (Continued)

UNIT

MODEL

YHJD30S41S1

YHJD36S41S1

For Notes See Page 10.

FURNACE

MODEL

(Y*9C/T*9V)*C16 FC/MC/PC43C 21 1030 29.6 22.2 14.00 12.60 (Y*9C/T*9V)*C20 FC/MC/PC43C 21 995 29.6 22.4 14.40 12.80

Y*(8,L)C*C16 HC42 21 990 29.6 22.4 14.50 13.00

Y*(8,L)C*C20 HC42 21 1000 29.8 22.4 14.50 13.00

(Y*9C/T*9V)*C16 HC42 21 1030 29.4 22.2 14.00 12.60 (Y*9C/T*9V)*C20 HC42 21 995 29.6 22.4 14.40 12.80

Y*(8,L)C*A12 HD36 14 1000 28.6 21.0 13.50 12.20

Y*(8,L)C*B12 HD36 17 985 28.8 21.0 13.80 12.40

Y*(8,L)C*C16 HD36 21 1020 28.8 21.2 13.90 12.60

Y*(8,L)C*C20 HD36 21 1055 29.2 21.8 14.10 12.70

(Y*9C/T*9V)*B12 HD36 17 985 28.8 21.0 13.70 12.40 (Y*9C/T*9V)*C16 HD36 21 1005 28.8 21.2 13.90 12.60 (Y*9C/T*9V)*C20 HD36 21 1045 28.8 21.0 13.80 12.40

T*9X*B12 FC/MC/PC43B 17 1270 36.4 27.4 14.00 11.70 T*(8,L)X*B12 FC/MC/PC43B 17 1300 36.4 27.4 14.05 11.70 T*(8,L)X*C16 FC/MC/PC43C 21 1175 36.4 27.0 14.70 12.20

T*9X*C16 FC/MC/PC43C 21 1260 36.4 27.6 14.20 11.80

T*(8,L)X*C20 FC/MC/PC43C 21 1250 36.6 27.6 14.55 12.20

T*9X*C20 FC/MC/PC43C 21 1185 36.2 26.8 14.30 12.00

Y*(8,L)C*A12 FC/MC/PC37A 14 980 34.2 22.6 14.00 11.70 Y*(8,L)C*B12 FC/MC/PC43B 17 1210 35.4 25.0 14.00 11.70

(Y*9C/T*9V)*B12 FC/MC/PC43B 17 1200 35.4 25.0 14.00 11.70

Y*(8,L)C*C16 FC/MC/PC43C 21 1205 35.6 25.2 14.60 12.20 Y*(8,L)C*C20 FC/MC/PC43C 21 1190 35.6 25.2 14.80 12.20

(Y*9C/T*9V)*C16 FC/MC/PC43C 21 1240 35.4 25.0 14.20 11.80 (Y*9C/T*9V)*C20 FC/MC/PC43C 21 1200 35.6 25.2 14.50 12.10

Y*(8,L)C*C16 FC/MC/PC48C 21 1210 36.0 25.4 14.90 12.40 Y*(8,L)C*C20 FC/MC/PC48C 21 1155 36.0 25.4 15.10 12.50

(Y*9C/T*9V)*C16 FC/MC/PC48C 21 1195 36.0 25.4 14.70 12.20 (Y*9C/T*9V)*C20 FC/MC/PC48C 21 1330 36.0 26.2 14.70 12.10

Y*(8,L)C*C16 HC42 21 1205 35.6 25.2 14.60 12.10 Y*(8,L)C*C20 HC42 21 1190 35.6 25.2 14.70 12.20

(Y*9C/T*9V)*C16 HC42 21 1240 35.2 25.0 14.10 11.80 (Y*9C/T*9V)*C20 HC42 21 1200 35.4 25.2 14.50 12.00

Y*(8,L)C*B12 HD48 17 1210 35.0 24.8 14.30 11.70 Y*(8,L)C*C16 HD48 21 1210 35.8 25.2 14.80 12.30 Y*(8,L)C*C20 HD48 21 1155 35.8 25.2 14.90 12.40

(Y*9C/T*9V)*B12 HD48 17 1150 35.0 24.8 14.20 11.70 (Y*9C/T*9V)*C16 HD48 21 1195 35.6 25.0 14.50 12.10 (Y*9C/T*9V)*C20 HD48 21 1330 35.6 26.0 14.40 11.80

Y*(8,L)C*C16 UC48C 21 1210 35.8 25.6 15.10 12.30 Y*(8,L)C*C20 UC48C 21 1155 36.0 25.6 15.20 12.40

*9C/T*9V)*C16 UC48C 21 1195 35.8 25.4 14.80 12.10

(Y (Y*9C

/T*9V)*C20

UC48C 21 1330 36.0 26.4 14.70 12.00

COIL

MODEL

13 SEER HP WITH VARIABLE SPEED FURNACES

RATED

CFM

TOTAL SENS.

Net MBH

COOLING

SEER EER

8 Johnson Controls Unitary Products

Page 9

COOLING CAPACITY - With High Efficiency Motor Furnaces (Continued)

UNIT

MODEL

YHJD42S41S1

For Notes See Page 10.

FURNACE

MODEL

COIL

MODEL

RATED

CFM

TOTAL SENS.

13 SEER HP WITH VARIABLE SPEED FURNACES

T*(8,L)X*C16 FC/MC/PC48C 21 1360 41.5 31.4 13.80 11.75

T*9X*C16 FC/MC/PC48C 21 1425 41.5 31.8 13.60 11.50

T*(8,L)X*C20 FC/MC/PC48C 21 1475 42.0 32.6 14.00 11.75

T*9X*C20 FC/MC/PC48C 21 1420 41.5 32.0 13.60 11.70 T*9X*D20 FC/MC/PC48D 24 1435 41.5 32.0 13.70 11.75

T*(8,L)X*C16 UC48C 21 1400 42.0 32.2 13.80 11.90

T*9X*C16 UC48C 21 1425 42.0 32.0 13.60 11.70

T*(8,L)X*C20 UC48C 21 1515 42.0 33.2 13.90 11.75

T*9X*C20 UC48C 21 1420 42.0 32.0 13.50 11.60

T*9X*D20 UC48D 24 1435 41.5 32.2 13.70 11.75

Y*(8,L)C*C16 FC/MC/PC48C 21 1435 41.5 32.6 13.80 11.90 Y*(8,L)C*C20 FC/MC/PC48C 21 1410 42.0 32.8 14.00 12.00

(Y*9C/T*9V)*C16 FC/MC/PC48C 21 1395 41.5 32.6 13.60 11.70 (Y*9C/T*9V)*C20 FC/MC/PC48C 21 1430 41.5 32.6 13.60 11.70 (Y*9C/T*9V)*D20 FC/MC/PC48D 24 1450 41.5 32.6 13.70 11.80 (Y*9C/T*9V)*D20 FC/MC/PC60D 24 1445 42.0 32.8 13.90 12.00 (Y*9C/T*9V)*D20 FC/MC62D 24 1455 42.0 33.0 13.80 12.00

Y*(8,L)C*C16 FC/PC60C 21 1420 42.0 32.8 14.00 12.10 Y*(8,L)C*C20 FC/PC60C 21 1410 42.0 32.8 14.20 12.30

(Y*9C/T*9V)*C16 FC/PC60C 21 1445 42.0 32.6 13.40 11.70 (Y*9C/T*9V)*C20 FC/PC60C 21 1445 42.0 32.8 13.70 11.90

Y*(8,L)C*B12 HD48 17 1350 41.0 30.8 13.20 11.40 Y*(8,L)C*C16 HD48 21 1435 40.5 31.6 13.60 11.60 Y*(8,L)C*C20 HD48 21 1410 41.0 31.0 13.60 11.80

(Y*9C/T*9V)*B12 HD48 17 1150 39.0 28.4 13.40 11.20 (Y*9C/T*9V)*C16 HD48 21 1395 41.0 30.8 13.30 11.60 (Y*9C/T*9V)*C20 HD48 21 1430 41.5 31.8 13.40 11.70 (Y*9C/T*9V)*D20 HD48 24 1450 41.0 31.8 13.60 11.70

Y*(8,L)C*C16 UC48C 21 1435 41.5 32.4 13.80 11.90 Y*(8,L)C*C20 UC48C 21 1410 41.5 32.4 13.90 12.00

(Y*9C/T*9V)*C16 UC48C 21 1395 41.5 32.2 13.60 11.70 (Y*9C/T*9V)*C20 UC48C 21 1430 41.0 32.2 13.50 11.60 (Y*9C/T*9V)*D20 UC48D 24 1450 41.5 32.2 13.70 11.80

Y*(8,L)C*C16 UC60C 21 1420 41.5 32.0 13.80 11.90 Y*(8,L)C*C20 UC60C 21 1410 41.5 32.2 14.00 12.10

(Y*9C/T*9V)*C16 UC60C 21 1445 41.0 31.8 13.20 11.50 (Y*9C/T*9V)*C20 UC60C 21 1445 41.5 32.0 13.50 11.70 (Y*9C/T*9V)*D20 UC60D 24 1445 41.5 32.0 13.70 11.90

Net MBH

COOLING

SEER EER

Johnson Controls Unitary Products 9

Page 10

397855-YTG-G-0509

COOLING CAP ACITY - With High Efficiency Motor Furnaces (Continued)

UNIT

MODEL

YHJD48S41S1

YHJD60S41S1

1. MC coils available with a factory installed horizontal drain pan. See price pages for specific model number.

2. Variable speed furnaces have B.O.D (Blower on Delay) standard.

FURNACE

MODEL

COIL

MODEL

RATED

CFM

TOTAL SENS.

13 SEER HP WITH VARIABLE SPEED FURNACES

T*(8,L)X*C16 FC/PC60C 21 1605 46.5 34.6 13.50 11.50

T*9X*C16 FC/PC60C 21 1575 46.5 34.6 13.30 11.40

T*(8,L)X*C20 FC/MC/PC60D 21 1595 46.5 34.6 13.55 11.50

T*9X*C20 FC/PC60C 21 1625 46.5 34.8 13.30 11.40 T*9X*D20 FC/MC/PC60D 24 1490 46.5 34.0 13.50 11.50

T*9X*D20 FC/MC62D 24 1610 47.0 35.4 13.40 11.50 T*(8,L)X*C16 UC60C 21 1640 46.5 34.8 13.40 11.40 T*(8,L)X*C20 UC60D 21 1540 46.5 34.2 13.70 11.70

T*9X*C16 UC60C 21 1575 46.5 34.8 13.20 11.30

T*9X*C20 UC60C 21 1625 46.5 34.8 13.10 11.30

T*9X*D20 UC60D 24 1490 46.0 33.6 13.30 11.40

(Y*9C/T*9V)*D20 FC/MC/PC60D 24 1615 46.5 35.2 13.50 11.50 (Y*9C/T*9V)*D20 FC/MC62D 24 1630 46.5 35.6 13.40 11.50

Y*(8,L)C*C16 FC/PC60C 21 1625 46.5 35.4 13.50 11.60 Y*(8,L)C*C20 FC/PC60C 21 1605 46.5 35.6 13.80 11.80

(Y*9C/T*9V)*C16 FC/PC60C 21 1590 46.5 35.2 13.30 11.40 (Y*9C/T*9V)*C20 FC/PC60C 21 1655 46.5 35.2 13.30 11.40 (Y*9C/T*9V)*D20 HC60 24 1615 46.0 35.0 13.40 11.40

Y*(8,L)C*C16 HD60 21 1625 46.5 35.4 13.50 11.60 Y*(8,L)C*C20 HD60 21 1605 47.0 35.6 13.70 11.80

(Y*9C/T*9V)*C16 HD60 21 1590 46.5 35.2 13.20 11.40 (Y*9C/T*9V)*C20 HD60 21 1655 46.5 35.2 13.20 11.40 (Y*9C/T*9V)*D20 HD60 24 1615 46.5 35.4 13.40 11.50

Y*(8,L)C*C16 UC60C 21 1625 46.0 34.4 13.40 11.40 Y*(8,L)C*C20 UC60C 21 1605 46.0 34.6 13.70 11.70

(Y*9C/T*9V)*C16 UC60C 21 1590 46.0 34.4 13.20 11.30 (Y*9C/T*9V)*C20 UC60C 21 1655 46.0 34.4 13.10 11.30 (Y*9C/T*9V)*D20 UC60D 24 1615 46.0 34.2 13.30 11.40

T*(8,L)X*C20 FC/MC62D 21 1665 56.0 41.5 13.80 11.50

T*9X*D20 FC/MC62D 24 1515 54.5 39.0 13.10 11.00

(Y*9C/T*9V)*D20 FC/MC/PC60D 24 1615 53.5 41.0 13.30 11.60

Y*(8,L)C*C20 FC/MC62D 21 1615 54.0 41.5 13.60 11.80

(Y*9C/T*9V)*C20 FC/MC62D 21 1655 53.5 41.0 13.20 11.40 (Y*9C/T*9V)*D20 FC/MC/PC60D 24 1615 53.5 41.0 13.30 11.60 (Y*9C/T*9V)*C20 FC/MC62D 21 1655 53.5 41.0 13.20 11.40

Net MBH

COOLING

SEER EER

10 Johnson Controls Unitary Products

Page 11

HEATING PERFORMANCE - With Air Handler

UNIT

MODEL*

AIR

HANDLER

COIL

MODEL

47F17F HSPF

MBH COP KW MBH COP KW STD

ARI HEATING

13 SEER HP WITH MA

YHJD18S41S1

MA08B FC/MC18B 17.0 3.32 1.50 12.7 3.00 1.24 7.70

MA08B FC/MC24B 17.0 3.44 1.45 10.4 2.60 1.17 7.70

YHJD24S41S1 MA08B FC/MC/PC35B 23.2 3.40 2.00 12.6 2.24 1.65 7.70 YHJD30S41S1 MA12B FC/MC/PC43B 28.2 3.40 2.43 16.6 2.32 2.10 7.70

MA12B FC/MC/PC43B 35.0 3.42 3.00 21.2 2.36 2.63 8.00

YHJD36S41S1

MA14D FC/MC/PC48D 35.0 3.42 3.00 21.4 2.36 2.66 8.00

MA16C FC/MC43C 35.0 3.48 3.03 21.0 2.40 2.56 8.00

MA16C FC/MC48C 35.0 3.48 3.03 21.0 2.40 2.56 8.00

MA14D FC/MC/PC48D 41.0 3.48 3.45 28.0 2.46 3.34 8.00

YHJD42S41S1

MA16C FC/MC/PC48C 41.0 3.48 3.45 28.0 2.46 3.34 8.00

MA14D FC/MC/PC60D 41.0 3.66 3.28 27.8 2.56 3.18 8.00

MA16C FC/MC/PC60C 41.0 3.66 3.28 27.8 2.56 3.18 8.00

MA16C FC/MC/PC60C 51.0 3.50 4.27 30.6 2.34 3.83 8.00

YHJD48S41S1

MA20D FC/MC/PC60D 51.0 3.50 4.27 30.6 2.34 3.83 8.00

MA20D MC62D 50.5 3.38 4.38 30.6 2.28 3.93 8.00

YHJD60S41S1 MA20D MC62D 56.5 3.48 4.76 35.4 2.42 4.29 8.00

13 SEER HP WITH MV - VARIABLE SPEED

YHJD18S41S1

YHJD24S41S1

YHJD30S41S1

MV12B FC/MC18B 16.7 3.52 1.39 12.7 3.00 1.24 8.00

MV12B FC/MC24B 17.0 3.66 1.36 9.8 2.78 1.03 8.00

MV12B FC/MC/PC35B 22.8 3.72 1.80 12.4 2.50 1.45 8.00

MV16C FC/MC/PC35C 22.8 3.72 1.80 12.4 2.50 1.45 8.00

MV12B FC/MC/PC43B 27.8 3.58 2.28 16.1 2.46 1.92 8.00

MV16C FC/MC/PC43C 27.6 3.60 2.25 16.1 2.48 1.90 8.00

MV12B FC/MC/PC43B 35.0 3.52 2.91 20.8 2.44 2.50 8.00

MV16C FC/MC/PC43C 35.0 3.58 2.87 20.6 2.48 2.43 8.00

YHJD36S41S1

MV12D FC/MC/PC48D 35.0 3.54 2.90 20.6 2.48 2.43 8.00

MV16C FC/MC/PC48C 35.0 3.60 2.85 20.6 2.50 2.42 8.00

MV20D FC/MC/PC48D 35.0 3.60 2.85 20.6 2.50 2.42 8.00

MV16C FC/MC/PC48C 41.0 3.60 3.34 27.4 2.54 3.16 8.00

YHJD42S41S1

MV20D FC/MC/PC48D 41.0 3.62 3.32 27.4 2.56 3.14 8.00

MV20D FC/MC/PC60D 41.0 3.84 3.13 27.0 2.68 2.95 8.00

YHJD48S41S1

MV20D FC/MC/PC60D 50.5 3.60 4.11 30.2 2.40 3.69 8.00

MV20D MC62D 50.0 3.48 4.21 30.0 2.34 3.76 8.00

YHJD60S41S1 MV20D MC62D 56.5 3.54 4.68 35.2 2.46 4.19 8.00

13 SEER HP WITH AV / SV / F*FV - VARIABLE SPEED

YHJD18S41S1 AV*24 – 16.8 3.62 1.36 11.5 3.18 1.06 8.00 YHJD24S41S1 AV*36 – 22.6 3.68 1.80 12.0 2.44 1.44 8.20 YHJD30S41S1 AV*36 – 27.6 3.64 2.22 16.0 2.50 1.88 8.00 YHJD36S41S1 AV*36 – 35.0 3.68 2.79 20.4 2.54 2.35 8.20 YHJD42S41S1 AV/SV*48 – 41.0 3.64 3.30 27.0 2.58 3.07 8.50

AV/SV*48 – 50.5 3.62 4.09 30.0 2.42 3.63 8.00

YHJD48S41S1

AV/SV*60 – 48.03.464.0630.02.343.768.20

F4FV060 – 50.5 3.62 4.09 30.2 2.40 3.69 8.00

For Notes See Page 12.

Johnson Controls Unitary Products 11

Page 12

397855-YTG-G-0509

HEATING PERFORMANCE - With Air Handler (Continued)

UNIT

MODEL*

YHJD18S41S1

YHJD24S41S1

YHJD30S41S1

YHJD36S41S1

YHJD42S41S1

YHJD48S41S1

YHJD60S41S1

1. Rated CFM same as for cooling.

2. Heating MBH based on ARI standards of 70° DB entering indoor air, 72% RH outdoor air with 25 feet of interconnecting piping and no supplemental electric heat operation.

CP equals MBH output divided by (total KW input x 3.412). HSPF (Heating Seasonal Performance Factor) is the total heating output during a normal annual usage period for heating divided by the total electric power input during the same period. — = Not Applicable.

AIR

HANDLER

13 SEER HP WITH AHP / SHP / AHX / F*FP

AHP18 – 17.0 3.38 1.47 8.2 2.16 1.11 7.70

F4FP24 – 17.0 3.34 1.49 12.5 3.04 1.21 7.70

AHP30 – 23.2 3.40 2.00 12.6 2.24 1.65 7.70 AHX30 – 22.63.661.8112.12.421.468.20

AHX36 – 22.63.801.7412.12.481.438.20 F6FP030 – 22.63.601.8412.22.361.518.10 F6FP036 – 22.63.661.8112.12.381.498.10

AHP36 – 28.2 3.40 2.43 16.6 2.32 2.10 7.70

AHX36 – 27.63.682.2015.92.541.838.00 F6FP036 – 27.23.502.2815.92.461.897.80

AHP36 – 35.0 3.40 3.02 21.0 2.40 2.56 8.00

AHX36 – 35.03.722.7620.42.562.338.20 F4FP045 – 35.0 3.40 3.02 21.6 2.42 2.62 8.00 F6FP042 – 35.43.782.7421.02.542.428.20

AHP/SHP48 – 41.0 3.32 3.62 28.2 2.36 3.50 8.00

AHX42 – 41.03.683.2627.02.603.048.50

AHX48 – 41.03.703.2527.02.603.048.50 F4FP045 – 41.0 3.68 3.27 27.8 2.56 3.18 8.00 F5FP048 – 41.0 3.68 3.27 27.6 2.58 3.14 8.00 F6FP042 – 41.03.803.1627.02.662.978.50 F6FP048 – 41.03.683.2627.02.583.078.20

AHP/SHP60 – 50.5 3.58 4.13 30.2 2.40 3.69 8.00

AHX48 – 48.03.524.0029.02.343.638.20 F5FP048 – 50.5 3.46 4.28 30.6 2.32 3.87 8.00 F5FP060 – 50.5 3.60 4.11 30.2 2.40 3.69 8.00 F6FP048 – 48.03.603.9129.02.403.548.20

AHX60 – 56.03.444.7734.82.444.188.10 F6FP060 – 57.03.584.6734.02.404.158.10

COIL

MODEL

47F17FHSPF

MBH COP KW MBH COP KW STD

ARI HEATING

12 Johnson Controls Unitary Products

Page 13

HEATING PERFORMANCE - Upflow, Downflow, and Horizontal Furnaces and Coils

UNIT

MODEL*

COIL

MODEL

47F17F HSPF

MBH COP KW MBH COP KW STD

ARI HEATING

FC/MC/PC/UC18 17.0 3.32 1.50 12.7 3.00 1.24 7.70 FC/MC/PC/UC24 17.0 3.44 1.45 10.4 2.60 1.17 7.70

YHJD18S41S1

HC18 17.0 3.32 1.50 12.7 3.00 1.24 7.70 HC30 17.0 3.38 1.47 10.4 2.60 1.17 7.70

HD24 16.6 3.16 1.54 12.8 3.00 1.25 7.70 FC/MC/PC32 23.2 3.40 2.00 12.6 2.24 1.65 7.70 FC/MC/PC35 23.2 3.40 2.00 12.6 2.24 1.65 7.70

YHJD24S41S1

HC30 23.0 3.40 1.98 12.6 2.24 1.65 7.70

HC36 23.2 3.40 2.00 12.6 2.24 1.65 7.70

HD36 23.2 3.40 2.00 12.6 2.24 1.65 7.70 FC/MC/PC37 28.2 3.40 2.43 16.6 2.32 2.10 7.70

YHJD30S41S1

FC/MC/PC43 28.2 3.40 2.43 16.6 2.32 2.10 7.70

HC42 28.2 3.40 2.43 16.6 2.32 2.10 7.70

HD48 28.2 3.60 2.30 16.6 2.32 2.10 7.70 FC/MC/PC37 35.0 3.40 3.02 21.2 2.36 2.63 8.00 FC/MC/PC43 35.0 3.42 3.00 21.2 2.36 2.63 8.00

YHJD36S41S1

FC/MC/PC48 35.0 3.42 3.00 21.4 2.36 2.66 8.00

HC42 35.0 3.42 3.00 21.2 2.36 2.63 8.00

HD48 35.0 3.40 3.02 20.0 2.16 2.71 8.00 FC/MC/PC60 41.0 3.66 3.28 27.8 2.56 3.18 8.00

YHJD42S41S1

HC60 41.0 3.66 3.28 27.8 2.56 3.18 8.00

HD60 41.0 3.14 3.83 27.6 2.26 3.58 8.00 FC/MC/PC48 50.5 3.32 4.46 30.8 2.24 4.03 8.00 FC/MC/PC60 51.0 3.50 4.27 30.6 2.34 3.83 8.00

YHJD48S41S1

HC60 51.0 3.50 4.27 30.6 2.34 3.83 8.00

HD60 50.0 2.98 4.92 30.6 2.06 4.35 8.00

MC62 50.5 3.38 4.38 30.6 2.28 3.93 8.00

YHJD60S41S1 MC62 56.5 3.48 4.76 35.4 2.42 4.29 8.00

1. Rated CFM same as for cooling.

2. Heating MBH based on ARI standards of 70° DB entering indoor air, 72% RH outdoor air with 25 feet of interconnecting piping and no supplemental electric heat operation.

Johnson Controls Unitary Products 13

Page 14

397855-YTG-G-0509

HEATING CAPACITY - With High Efficiency Motor Furnaces

MODEL

(Y*9C/T*9V)*B12 FC/MC/PC18B 16.7 3.60 1.36 7.7 2.30 0.98 8.00

(Y*9C/T*9V)*B12 FC/MC/PC24B 17.1 3.74 1.34 10.5 2.94 1.05 8.30

(Y*9C/T*9V)*B12 FC/MC/PC30B 17.1 3.74 1.34 10.5 2.94 1.05 8.30

YHJD18S41S1

(Y*9C/T*9V)*B12 HD24 16.7 3.58 1.37 8.7 2.50 1.02 8.00

(Y*9C/T*9V)*B12 UC18B 16.8 3.64 1.35 9.1 2.62 1.02 8.10

(Y*9C/T*9V)*B12 UC24B 17.2 3.76 1.34 10.7 2.96 1.06 8.30

(Y*9C/T*9V)*B12 UC30B 17.2 3.76 1.34 10.7 2.96 1.06 8.30

(Y*9C/T*9V)*B12 FC/MC/PC35B 22.8 3.58 1.87 12.3 2.32 1.55 8.20

YHJD24S41S1

(Y*9C/T*9V)*B12 FC/MC/PC43B 23.0 3.64 1.85 12.6 2.40 1.54 8.30

(Y*9C/T*9V)*B12 HC36 22.8 3.58 1.87 12.3 2.32 1.55 8.20

(Y*9C/T*9V)*B12 HD36 21.0 3.08 2.00 9.1 1.82 1.47 7.70 (Y*9C/T*9V)*C16 HD36 20.8 3.10 1.97 9.0 1.82 1.45 7.70 (Y*9C/T*9V)*C20 HD36 20.4 3.02 1.98 7.4 1.64 1.32 7.70

YHJD30S41S1

For Notes See Page 17.

FURNACE

MODEL

Y*(8,L)C*A12 FC/MC/PC18A 16.7 3.58 1.37 7.7 2.28 0.99 8.00 Y*(8,L)C*B12 FC/MC/PC18B 16.6 3.56 1.37 7.7 2.30 0.98 7.90

Y*(8,L)C*A12 FC/MC/PC24A 17.2 3.70 1.36 10.6 2.90 1.07 8.30 Y*(8,L)C*B12 FC/MC/PC24B 16.8 3.68 1.34 10.1 2.88 1.03 8.20

Y*(8,L)C*A12 FC/MC/PC30A 17.2 3.70 1.36 10.6 2.90 1.07 8.30 Y*(8,L)C*B12 FC/MC/PC30B 16.8 3.68 1.34 10.1 2.88 1.03 8.20

Y*(8,L)C*A12 HC18 16.7 3.58 1.37 7.7 2.28 0.99 8.00 Y*(8,L)C*A12 HC30 16.8 3.58 1.38 10.1 2.80 1.06 8.00 Y*(8,L)C*A12 HD24 16.7 3.56 1.37 8.8 2.48 1.04 8.00 Y*(8,L)C*B12 HD24 16.3 3.50 1.36 9.1 2.62 1.02 7.80

Y*(8,L)C*A12 UC18A 16.9 3.62 1.37 9.1 2.58 1.03 8.10 Y*(8,L)C*B12 UC18B 16.7 3.60 1.36 9.7 2.74 1.04 8.00

Y*(8,L)C*A12 UC24A 17.3 3.72 1.36 10.7 2.94 1.07 8.30 Y*(8,L)C*B12 UC24B 16.9 3.70 1.34 10.5 2.96 1.04 8.20

Y*(8,L)C*A12 UC30A 17.3 3.72 1.36 10.7 2.94 1.07 8.30 Y*(8,L)C*B12 UC30B 16.9 3.70 1.34 10.4 2.96 1.03 8.20

T*9X*B12FC/MC/PC35B22.63.661.8112.02.421.458.00 T*(8,L)X*A12 FC/MC/PC37A 23.2 3.82 1.78 12.2 2.48 1.44 8.25 T*(8,L)X*B12 FC/MC/PC43B 23.2 3.84 1.77 12.2 2.50 1.43 8.30

T*9X*B12FC/MC/PC43B23.03.761.7912.12.461.448.15 T*(8,L)X*B12 FC/MC/PC35B 22.8 3.74 1.79 12.1 2.44 1.45 8.10

T*9X*C16 FC/MC/PC35C 22.2 3.60 1.81 11.8 2.40 1.44 7.85 T*(8,L)X*A12 FC/MC/PC32A 22.8 3.68 1.82 12.1 2.44 1.45 8.00

Y*(8,L)C*A12 FC/MC/PC32A 22.8 3.52 1.90 12.0 2.28 1.54 8.20 Y*(8,L)C*B12 FC/MC/PC35B 22.6 3.58 1.85 11.9 2.32 1.50 8.20

Y*(8,L)C*A12 FC/MC/PC37A 23.0 3.62 1.86 12.8 2.40 1.56 8.30 Y*(8,L)C*B12 FC/MC/PC43B 22.8 3.64 1.84 12.6 2.42 1.53 8.30

Y*(8,L)C*B12 HC36 22.6 3.56 1.86 12.1 2.34 1.52 8.20

Y*(8,L)C*A12 HD36 21.0 3.06 2.01 9.1 1.80 1.48 7.70 Y*(8,L)C*B12 HD36 20.6 3.02 2.00 8.9 1.80 1.45 7.70 Y*(8,L)C*C16 HD36 21.2 3.16 1.97 9.2 1.86 1.45 7.70 Y*(8,L)C*C20 HD36 20.4 3.04 1.97 7.4 1.64 1.32 7.70

T*(8,L)X*A12 FC/MC/PC37A 29.0 3.68 2.30 16.3 2.48 1.93 7.80

9X*B12FC/MC/PC43B29.03.702.3016.32.481.937.90

T T*(8,L)X*B12 FC/MC/PC43B 29.0 3.68 2.30 16.3 2.48 1.93 7.90

Y*(8,L)C*A12 FC/MC/PC37A 27.8 3.48 2.34 16.3 2.46 1.94 7.80 Y*(8,L)C*B12 FC/MC/PC43B 27.8 3.56 2.29 16.2 2.52 1.88 7.90

COIL

MODEL

MBH COP KW MBH COP KW STD

47F17FHSPF

13 SEER HP WITH VARIABLE SPEED FURNACES

ARI HEATING

14 Johnson Controls Unitary Products

Page 15

HEATING CAPACITY - With High Efficiency Motor Furnaces (Continued)

MODEL

(Y*9C/T*9V)*B12 FC/MC/PC43B 28.0 3.50 2.34 16.3 2.48 1.93 7.90

(Y*9C/T*9V)*C16 FC/MC/PC43C 27.8 3.56 2.29 16.2 2.52 1.88 7.90 (Y*9C/T*9V)*C20 FC/MC/PC43C 27.6 3.60 2.25 16.1 2.56 1.84 8.00

YHJD30S41S1

(Y*9C/T*9V)*C16 HC42 27.8 3.56 2.29 16.2 2.52 1.88 7.90 (Y*9C/T*9V)*C20 HC42 27.6 3.60 2.25 16.1 2.54 1.86 8.00

(Y*9C/T*9V)*B12 HD36 26.0 3.10 2.46 14.1 2.12 1.95 7.70 (Y*9C/T*9V)*C16 HD36 26.0 3.14 2.43 14.0 2.14 1.92 7.70 (Y*9C/T*9V)*C20 HD36 26.0 3.12 2.44 14.1 2.12 1.95 7.70

(Y*9C/T*9V)*B12 FC/MC/PC43B 35.8 3.48 3.02 20.8 2.44 2.50 8.40

(Y*9C/T*9V)*C16 FC/MC/PC43C 35.8 3.50 3.00 20.8 2.46 2.48 8.40 (Y*9C/T*9V)*C20 FC/MC/PC43C 35.6 3.54 2.95 20.6 2.50 2.42 8.50

YHJD36S41S1

(Y*9C/T*9V)*C16 FC/MC/PC48C 35.6 3.56 2.93 20.6 2.52 2.40 8.50 (Y*9C/T*9V)*C20 FC/MC/PC48C 36.2 3.58 2.96 21.0 2.50 2.46 8.60

(Y*9C/T*9V)*C16 HC42 35.8 3.50 3.00 20.8 2.46 2.48 8.40 (Y*9C/T*9V)*C20 HC42 35.6 3.54 2.95 20.6 2.50 2.42 8.50

(Y*9C/T*9V)*B12 HD48 34.4 3.22 3.13 19.3 2.24 2.53 8.00 (Y*9C/T*9V)*C16 HD48 34.2 3.26 3.07 19.1 2.28 2.46 8.00 (Y

(Y*9C/T*9V)*C16 UC48C 36.0 3.66 2.88 20.8 2.54 2.40 8.60 (Y*9C/T*9V)*C20 UC48C 36.6 3.64 2.95 21.0 2.52 2.44 8.70

For Notes See Page 17.

FURNACE

MODEL

Y*(8,L)C*C16 FC/MC/PC43C 27.6 3.62 2.23 16.0 2.56 1.83 8.00 Y*(8,L)C*C20 FC/MC/PC43C 27.6 3.62 2.23 16.0 2.56 1.83 8.00

Y*(8,L)C*C16 HC42 27.6 3.62 2.23 16.0 2.56 1.83 8.00 Y*(8,L)C*C20 HC42 27.6 3.62 2.23 16.0 2.56 1.83 8.00

Y*(8,L)C*A12 HD36 26.2 3.08 2.49 14.2 2.10 1.98 7.70 Y*(8,L)C*B12 HD36 26.0 3.12 2.44 14.0 2.12 1.94 7.70 Y*(8,L)C*C16 HD36 26.0 3.12 2.44 14.0 2.14 1.92 7.70 Y*(8,L)C*C20 HD36 26.2 3.18 2.41 14.1 2.16 1.91 7.70

T*9X*B12 FC/MC/PC43B 35.0 3.60 2.85 20.8 2.52 2.42 8.20 T*(8,L)X*B12 FC/MC/PC43B 35.0 3.60 2.85 20.6 2.52 2.40 8.20 T*(8,L)X*C16 FC/MC/PC43C 34.2 3.66 2.74 20.2 2.58 2.29 8.20

T*9X*C16 FC/MC/PC43C 35.0 3.62 2.83 20.6 2.54 2.38 8.25 T*(8,L)X*C20 FC/MC/PC43C 34.8 3.68 2.77 20.4 2.58 2.32 8.30

T*9X*C20 FC/MC/PC43C 34.6 3.60 2.82 20.4 2.54 2.35 8.20

Y*(8,L)C*A12 FC/MC/PC37A 34.6 3.36 3.02 20.2 2.44 2.43 8.20 Y*(8,L)C*B12 FC/MC/PC43B 35.8 3.46 3.03 20.8 2.44 2.50 8.40

Y*(8,L)C*C16 FC/MC/PC43C 35.4 3.56 2.91 20.4 2.52 2.37 8.50 Y*(8,L)C*C20 FC/MC/PC43C 35.4 3.56 2.91 20.4 2.52 2.37 8.50

Y*(8,L)C*C16 FC/MC/PC48C 35.4 3.58 2.90 20.4 2.54 2.35 8.50 Y*(8,L)C*C20 FC/MC/PC48C 35.4 3.62 2.87 20.4 2.56 2.34 8.60

Y*(8,L)C*C16 HC42 35.4 3.56 2.91 20.4 2.52 2.37 8.50 Y*(8,L)C*C20 HC42 35.4 3.58 2.90 20.4 2.54 2.35 8.50

Y*(8,L)C*B12 HD48 34.2 3.22 3.11 19.2 2.24 2.51 8.00 Y*(8,L)C*C16 HD48 34.0 3.28 3.04 19.0 2.30 2.42 8.10 Y*(8,L)C*C20 HD48 34.0 3.30 3.02 18.9 2.32 2.39 8.10

*9C/T*9V)*C20 HD48 34.8 3.30 3.09 19.5 2.28 2.51 8.10

8,L)C*C16 UC48C 36.0 3.68 2.87 20.6 2.56 2.36 8.70

(

Y* Y*(8,L)C*C20 UC48C 35.8 3.72 2.82 20.6 2.60 2.32 8.70

COIL

MODEL

47F17F HSPF

MBH COP KW MBH COP KW STD

ARI HEATING

Johnson Controls Unitary Products 15

Page 16

397855-YTG-G-0509

HEATING CAPACITY - With High Efficiency Motor Furnaces (Continued)

MODEL

(Y*9C/T*9V)*C16 FC/MC/PC48C 41.5 3.52 3.46 27.6 2.46 3.29 8.90 (Y*9C/T*9V)*C20 FC/MC/PC48C 42.0 3.50 3.52 27.8 2.46 3.31 8.90 (Y*9C/T*9V)*D20 FC/MC/PC48D 41.5 3.52 3.46 27.6 2.48 3.26 8.90 (Y*9C/T*9V)*D20 FC/MC/PC60D 42.0 3.66 3.36 27.4 2.54 3.16 9.00 (Y*9C/T*9V)*D20 FC/MC62D 42.0 3.60 3.42 27.0 2.48 3.19 9.00

YHJD42S41S1

For Notes See Page 17.

(Y*9C/T*9V)*C16 FC/PC60C 42.0 3.58 3.44 27.8 2.50 3.26 9.00 (Y*9C/T*9V)*C20 FC/PC60C 42.0 3.64 3.38 27.6 2.52 3.21 9.00

(Y*9C/T*9V)*B12 HD48 40.5 2.96 4.01 26.8 2.12 3.71 8.70 (Y*9C/T*9V)*C16 HD48 41.0 3.14 3.83 27.0 2.20 3.60 8.70 (Y*9C/T*9V)*C20 HD48 41.0 3.20 3.76 26.8 2.22 3.54 8.70 (Y*9C/T*9V)*D20 HD48 41.0 3.24 3.71 27.0 2.26 3.50 8.80

(Y*9C/T*9V)*C16 UC48C 42.0 3.60 3.42 27.6 2.50 3.24 9.00 (Y*9C/T*9V)*C20 UC48C 42.0 3.58 3.44 27.6 2.50 3.24 9.00 (Y*9C/T*9V)*D20 UC48D 42.0 3.62 3.40 27.4 2.52 3.19 9.00

(Y*9C/T*9V)*C16 UC60C 42.0 3.54 3.48 27.4 2.46 3.26 8.90 (Y*9C/T*9V)*C20 UC60C 42.0 3.58 3.44 27.2 2.48 3.21 9.00 (Y*9C/T*9V)*D20 UC60D 42.0 3.62 3.40 27.2 2.50 3.19 9.00

FURNACE

MODEL

T*(8,L)X*C16 FC/MC/PC48C 41.0 3.82 3.15 27.6 2.66 3.04 8.20

T*9X*C16 FC/MC/PC48C 41.5 3.80 3.20 27.8 2.64 3.09 8.10

T*(8,L)X*C20 FC/MC/PC48C 41.5 3.88 3.13 27.6 2.68 3.02 8.20

T*9X*C20 FC/MC/PC48C 41.5 3.82 3.18 27.6 2.66 3.04 8.10 T*9X*D20 FC/MC/PC48D 41.5 3.86 3.15 27.6 2.66 3.04 8.20

T*(8,L)X*C16 UC48C 41.54.003.0427.42.742.93 8.20

T*9X*C16 UC48C 41.5 3.90 3.12 27.6 2.68 3.02 8.20

T*(8,L)X*C20 UC48C 41.54.043.0127.42.762.91 8.20

T*9X*C20 UC48C 41.5 3.94 3.09 27.6 2.72 2.97 8.20

T*9X*D20 UC48D 41.5 3.98 3.06 27.4 2.74 2.93 8.20

Y*(8,L)C*C16 FC/MC/PC48C 41.5 3.54 3.44 27.6 2.48 3.26 9.00 Y*(8,L)C*C20 FC/MC/PC48C 41.5 3.56 3.42 27.4 2.50 3.21 9.00

Y*(8,L)C*C16 FC/PC60C 42.0 3.68 3.34 27.4 2.56 3.14 9.00 Y*(8,L)C*C20 FC/PC60C 41.5 3.72 3.27 27.2 2.58 3.09 9.10

Y*(8,L)C*B12 HD48 41.0 3.12 3.85 27.0 2.20 3.60 8.70 Y*(8,L)C*C16 HD48 41.0 3.22 3.73 26.8 2.26 3.48 8.80 Y*(8,L)C*C20 HD48 41.0 3.16 3.80 26.8 2.22 3.54 8.80

Y*(8,L)C*C16 UC48C 42.0 3.62 3.40 27.4 2.52 3.19 9.00 Y*(8,L)C*C20 UC48C 41.5 3.64 3.34 27.4 2.54 3.16 9.00

Y*(8,L)C*C16 UC60C 41.5 3.64 3.34 27.0 2.50 3.17 9.00 Y*(8,L)C*C20 UC60C 41.5 3.66 3.32 27.0 2.52 3.14 9.10

COIL

MODEL

47F17FHSPF

MBH COP KW MBH COP KW STD

ARI HEATING

16 Johnson Controls Unitary Products

Page 17

HEATING CAPACITY - With High Efficiency Motor Furnaces (Continued)

ARI HEATING

MODEL

FURNACE

MODEL

COIL

MODEL

47F17F HSPF

MBH COP KW MBH COP KW STD

T*(8,L)X*C16 FC/PC60C 47.0 3.46 3.98 32.8 2.28 4.22 8.00

T*9X*C16 FC/PC60C 47.0 3.46 3.98 32.8 2.28 4.22 8.00

T*(8,L)X*C20 FC/MC/PC60D 47.0 3.48 3.96 32.8 2.28 4.22 8.00

T*9X*C20 FC/PC60C 47.0 3.48 3.96 32.6 2.30 4.15 8.00 T*9X*D20 FC/MC/PC60D 46.5 3.50 3.89 32.2 2.32 4.07 8.10

T*9X*D20 FC/MC62D 47.5 3.54 3.93 32.6 2.30 4.15 8.00 T*(8,L)X*C16 UC60C 47.5 3.58 3.89 32.6 2.34 4.08 8.10 T*(8,L)X*C20 UC60D 47.0 3.64 3.78 32.0 2.40 3.91 8.10

T*9X*C16 UC60C 47.5 3.58 3.89 32.6 2.34 4.08 8.00

T*9X*C20 UC60C 47.5 3.60 3.87 32.6 2.34 4.08 8.10

T*9X*D20 UC60D 46.5 3.60 3.79 32.0 2.38 3.94 8.10

(Y*9C/T*9V)*D20 FC/MC/PC60D 47.5 3.38 4.12 30.4 2.38 3.74 8.50 (Y*9C/T*9V)*D20 FC/MC62D 48.0 3.44 4.09 30.2 2.40 3.69 8.50

YHJD48S41S1

Y*(8,L)C*C16 FC/PC60C 47.5 3.40 4.09 30.4 2.40 3.71 8.50 Y*(8,L)C*C20 FC/PC60C 47.5 3.46 4.02 30.2 2.42 3.66 8.60

(Y*9C/T*9V)*C16 FC/PC60C 48.0 3.38 4.16 30.6 2.38 3.77 8.50 (Y*9C/T*9V)*C20 FC/PC60C 48.0 3.38 4.16 30.6 2.38 3.77 8.50 (Y*9C/T*9V)*D20 HC60 48.0 3.48 4.04 30.4 2.44 3.65 8.50

Y*(8,L)C*C16 HD60 47.0 3.22 4.28 30.2 2.24 3.95 8.40 Y*(8,L)C*C20 HD60 47.0 3.24 4.25 30.0 2.28 3.86 8.40

(Y*9C/T*9V)*C16 HD60 47.5 3.18 4.38 30.2 2.24 3.95 8.40 (Y*9C/T*9V)*C20 HD60 47.5 3.18 4.38 30.2 2.24 3.95 8.40 (Y*9C/T*9V)*D20 HD60 47.5 3.20 4.35 30.2 2.24 3.95 8.40

Y*(8,L)C*C16 UC60C 47.5 3.46 4.02 30.2 2.42 3.66 8.50 Y*(8,L)C*C20 UC60C 47.5 3.52 3.95 30.0 2.46 3.57 8.60

(Y*9C/T*9V)*C16 UC60C 48.0 3.44 4.09 30.4 2.42 3.68 8.50 (Y*9C/T*9V)*C20 UC60C 48.0 3.44 4.09 30.4 2.42 3.68 8.50 (Y*9C/T*9V)*D20 UC60D 48.0 3.44 4.09 30.2 2.42 3.66 8.50

T*(8,L)X*C20 FC/MC62D 56.5 3.60 4.60 32.6 2.46 3.88 8.10

T*9X*D20 FC/MC62D 56.5 3.44 4.81 34.0 2.34 4.26 8.00

YHJD60S41S1

(Y*9C/T*9V)*D20 FC/MC/PC60D 55.5 3.30 4.93 35.0 2.40 4.27 8.50

Y*(8,L)C*C20 FC/MC62D 55.5 3.42 4.76 34.6 2.44 4.16 8.60

(Y*9C/T*9V)*C20 FC/MC62D 56.0 3.36 4.88 35.0 2.40 4.27 8.60

1. Rated CFM same as for cooling.

2. Heating MBH based on ARI standards of 70° DB entering indoor air, 72% RH outdoor air with 25 feet of interconnecting piping and no supplemental electric heat operation.

3. Variable speed furnaces have B.O.D (Blower on Delay) standard.

Johnson Controls Unitary Products 17

Page 18

397855-YTG-G-0509

ACCESSORIES

Refer to Price Manual for specific model numbers. Start Assist Kit (2SA067*) - May be required on 42, 48, 60

models. Models 18, 24, 30, 36 have been factory installed. Blower Time Delay - Available to increase efficiency when

installed. Installs on indoor section and maintains blower for approximately one minute after cooling thermostat has been satisfied.

Hard Start Kits - Provides required starting torque for use with Thermal Expansion Valve Kit.

Low Temperature Cutout (2LT06700224) - Prevents heat pump operation below -1°F ambient temperature.

Compressor Blanket - Designed to further reduce the normal operating sound.

Add-on Fossil Fuel Control - Interface controls for use with gas, oil furnaces and the heat pump system are available.

Thermal Expansion Valve Kit - 1TVM900 Series TXV kit used to improve system performance.

Outdoor Thermostat (2TD06700124) - Provides additional staging of supplement al electric heat.

Thermostats - Compatible thermostat controls are available through accessory sourcing. For optimum performance and installation, refer to the UPGNET “Low Voltage Wiring Diagram” document to select and apply controls.

SOUND POWER RATINGS

UNIT MODEL

018 73.1 80.4 024 72.9 75.0 030 76.8 80.4 036 76.5 78.2 042 72.7 75.2 048 76.7 78.1 060 77.2 78.9

* Rated in accordance with ARI 270-95 Standards.

Cooling Heating

(dBA)*

18 Johnson Controls Unitary Products

Page 19

TYPICAL INSTALLATION

THERMOSTAT

SEAL OPENING(S) WITH PERMAGUM OR EQUIVALENT

TO INDOOR COIL

TO FURNACE OR AIR HANDLER TERMINAL BLOCK

NEC CLASS 2 WIRING

NEC CLASS 1 WIRING

ALL OUTDOOR WIRING MUST BE WEATHERPROOF.

CONTROL ACCESS PANEL

WEATHERPROOF DISCONNECT SWITCH

MINIMUM 24” SERVICE ACCESS CLEARANCE ON ONE SIDE

48” OVERHEAD CLEARANCE

10” CLEARANCE AROUND PERIMETER

NOTE:

THERMOSTAT

INDOOR UNIT

OUTDOOR UNIT

LOW VOLTAGE TERMINAL BLOCK IN AIR HANDLER WITH ELECTRIC HEAT

DEFROST CONTROL

FIELD INSTALLED JUMPER

DEHUMIDIFICATION CONTROL CONNECTION (Humidistat* Jumper must be removed)

GND.

SCREW

CONTACTOR

LorX

X/L

GND.

LUG

CIRCUIT BREAKER***

POWER WIRING 24V CONTROL WIRING

(NEC CLASS 2)

JUMPER TERMINALS E AND W TO HEAT ON FIRST STAGE DURING EMERGENCY HEAT.

TERMINAL NOT USED ON ALL THERMOSTATS.

POWER WIRING

208/230-1-60

230-1-50

CHECK THE LOW VOLTAGE TERMINAL BLOCK ON THE INDOOR UNIT FOR THE ACTUAL ARRANGEMENT OF THE TERMINALS. CONNECT POWER WIRING TO TERMINAL BLOCK 3TB ON UNITS WITHOUT ELECTRIC HEAT OR CIRCUIT BREAKER.

BorC

ALL FIELD WIRING TO BE IN ACCORDANCE WITH ELECTRIC CODE (NEC) AND/OR LOCAL CODES

RED

BLK

YEL

ORG

BRN

PUR

WHT

GRY

/66

GRAY FOR USE WITH OPTIONAL OUTDOOR THERMOSTAT KITS.

3,4

TYPICAL FIELD WIRING

Johnson Controls Unitary Products 19

Page 20

397855-YTG-G-0509

COOLING PERFORMANCE DATA

CONDENSING UNIT MODEL NO. YHJD18S41S1 INDOOR COIL MODEL NO. AHP18

CONDENSING

ENTERING AIR

TEMPERATURE

105

115

125

NOTE: ALL CAPACITIES INCLUDE INDOOR FAN HEAT AT 1250 BTUH/1000 CFM.

Multipliers for determining the performance with other indoor sections.

NOTE: For dry bulb temperatures different than those listed (between 73-87 F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the listed

temperature and decreases by 1060 BTUH per 1000 CFM per degree below the listed temperature.

Air Handlers Coils T.C. S.C. KW

– FC/MC/PC18 0.99 0.99 1.00 – FC/MC/PC24 1.01 1.01 1.00 – HC18 0.99 0.99 1.00 – HC30 1.01 1.01 1.00 – HD24 1.03 1.02 1.00 AHP18 – 0.97 0.96 1.00 AV24 – 1.03 1.02 1.00 F4FP024 – 1.00 0.99 1.00 MA08B FC/MC/PC18B 0.99 0.99 1.00 MV12B FC/MC/PC18B 1.02 1.01 1.00 MA08B FC/MC/PC24B 1.01 1.01 1.00 MV12B FC/MC/PC24B 1.04 1.04 1.00

Furnaces Coils T.C. S.C. KW

Y*(8,L)C*A12 FC/MC/PC18A 1.03 1.05 0.93 Y*(8,L)C*B12 FC/MC/PC18B 1.02 1.01 0.92

(Y*9C/T*9V)*B12 FC/MC/PC18B 1.03 1.04 0.92

Y*(8,L)C*A12 FC/MC/PC24A 1.06 1.08 0.94

IDCFM 450 600 750 ID DB (°F) 80 80 75 80 80 80 80 75 80 80 80 80 75 80 80 ID WB (°F) 57 62 62 67 72 57 62 62 67 72 57 62 62 67 72

T.C. 17.6 20.2 20.2 22.5 24.9 20.4 21.5 21.8 24.2 26.7 23.2 22.7 23.4 25.9 28.4

S.C. 16.0 14.5 12.5 12.6 10.7 18.5 17.5 14.7 14.7 11.9 21.1 20.6 16.9 16.9 13.2

KW 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.0

T.C. 16.6 18.6 18.6 20.7 23.0 19.1 19.9 19.9 22.1 24.6 21.6 21.2 21.2 23.6 26.1

S.C. 15.0 13.8 11.8 11.9 10.0 17.3 16.5 14.0 14.0 11.2 19.6 19.3 16.1 16.1 12.4

KW 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2

T.C. 15.6 16.9 16.9 19.0 21.2 17.7 18.3 18.0 20.1 22.5 19.9 19.7 19.1 21.3 23.7

S.C. 14.1 13.1 11.1 11.2 9.3 16.1 15.5 13.2 13.2 10.5 18.1 17.9 15.3 15.3 11.6

KW 1.2 1.3 1.3 1.3 1.3 1.3 1.3 1.3 1.3 1.3 1.3 1.3 1.3 1.3 1.3

T.C. 14.5 15.3 15.3 17.2 19.3 16.4 16.8 16.1 18.1 20.3 18.3 18.3 16.9 19.0 21.4

S.C. 13.2 12.4 10.4 10.5 8.6 14.9 14.5 12.4 12.5 9.7 16.6 16.6 14.5 14.5 10.8

KW 1.3 1.3 1.3 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4

T.C. 13.2 13.6 13.4 15.2 17.0 14.7 14.9 14.2 16.0 17.9 16.3 16.3 15.0 16.7 18.7

S.C. 11.9 11.3 9.6 9.7 7.8 13.3 13.0 11.3 11.5 8.9 14.8 14.8 13.1 13.3 10.1

KW 1.4 1.4 1.4 1.5 1.5 1.5 1.5 1.4 1.5 1.5 1.5 1.5 1.5 1.5 1.5

T.C. 11.8 12.0 11.5 13.2 14.8 13.1 13.1 12.3 13.9 15.5 14.3 14.3 13.2 14.5 16.1

S.C. 10.7 10.4 8.9 9.0 7.1 11.9 11.7 10.3 10.6 8.2 13.0 13.0 11.7 12.3 9.3

KW 1.5 1.5 1.5 1.5 1.6 1.5 1.6 1.5 1.6 1.6 1.6 1.6 1.6 1.6 1.6

T.C. 10.5 10.3 9.7 11.2 12.6 11.4 11.3 10.5 11.8 13.1 12.3 12.3 11.3 12.3 13.6

S.C. 9.5 9.4 8.2 8.3 6.3 10.4 10.3 9.2 9.7 7.4 11.2 11.2 10.3 11.2 8.6

KW 1.6 1.6 1.6 1.6 1.7 1.6 1.6 1.6 1.7 1.7 1.7 1.7 1.7 1.7 1.7

Furnaces Coils T.C. S.C. KW

Y*(8,L)C*B12 FC/MC/PC24B 1.04 1.04 0.92

(Y*9C/T*9V)*B12 FC/MC/PC24B 1.06 1.08 0.93

Y*(8,L)C*A12 FC/MC/PC30A 1.06 1.08 0.94 Y*(8,L)C*B12 FC/MC/PC30B 1.04 1.04 0.92

(Y*9C/T*9V)*B12 FC/MC/PC30B 1.06 1.08 0.93

Y*(8,L)C*A12 HC18 1.03 1.05 0.93 Y*(8,L)C*A12 HC30 1.04 1.04 0.94 Y*(8,L)C*A12 HD24 1.06 1.08 0.94 Y*(8,L)C*B12 HD24 1.05 1.04 0.92

(Y*9C/T*9V)*B12 HD24 1.06 1.08 0.93

Y*(8,L)C*A12 UC18A 1.04 1.05 0.93 Y*(8,L)C*B12 UC18B 1.03 1.03 0.92

(Y*9C/T*9V)*B12 UC18B 1.04 1.05 0.92

Y*(8,L)C*A12 UC24A 1.06 1.09 0.94 Y*(8,L)C*B12 UC24B 1.05 1.05 0.92

(Y*9C/T*9V)*B12 UC24B 1.06 1.09 0.93

Y*(8,L)C*A12 UC30A 1.06 1.09 0.94 Y*(8,L)C*B12 UC30B 1.05 1.05 0.92

(Y*9C/T*9V)*B12 UC30B 1.06 1.09 0.93

20 Johnson Controls Unitary Products

Page 21

COOLING PERFORMANCE DATA

CONDENSING UNIT MODEL NO. YHJD24S41S1 INDOOR COIL MODEL NO. AHP30

CONDENSING

ENTERING AIR

TEMPERATURE

105

115

125

NOTE: ALL CAPACITIES I N CL UDE INDOO R FAN HEAT AT 1250 BTUH/1000 CFM.

Multipliers for determining the performance with other indoor sections.

NOTE: For dry bulb temperatures different than those listed (between 73-87 F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the listed

temperature and decreases by 1060 BTUH per 1000 CFM per degree below the listed temperature.

Air Handlers Coils T.C. S.C. KW

– FC/MC/PC24 0.98 0.98 1.00 – FC/MC/PC30 0.98 0.98 1.00 – FC/MC/PC32 1.00 1.00 1.00 – FC/MC/PC35 1.00 1.00 1.00 – HC30 0.98 0.99 1.00 – HC36 1.00 1.00 1.00 – HD36 0.98 0.94 1.00 AHP30 – 0.99 0.98 1.00 AHX30 – 1.02 1.06 0.93 AHX36 – 1.04 1.08 0.91 AV*24 – 0.99 0.98 1.00 AV*36 – 1.02 1.01 0.91 F4FP030 – 0.99 0.97 1.00 F6FP030 – 1.03 1.06 0.95 F6FP036 – 1.02 1.07 0.94 MA08B FC/MC/PC24B 0.98 0.98 1.00 MV12B FC/MC/PC24B 1.01 1.00 1.00 MA08B FC/MC/PC30B 0.98 0.98 1.00 MV12B FC/MC/PC30B 1.01 1.01 1.00 MA08B FC/MC/PC35B 1.00 1.00 1.00 MV12B FC/MC/PC35B 1.02 1.02 1.00 MV16C FC/MC/PC35C 1.02 1.02 1.00

IDCFM 600 800 1000

ID DB (°F) 80 80 75 80 80 80 80 75 80 80 80 80 75 80 80

ID WB (°F) 57 62 62 67 72 57 62 62 67 72 57 62 62 67 72

T.C. 22.9 26.4 25.6 29.2 31.5 25.8 28.0 27.2 30.7 33.2 28.8 29.6 28.8 32.2 35.0

S.C. 21.8 20.2 17.3 17.7 15.1 24.6 23.7 19.4 19.6 16.2 27.4 27.2 21.5 21.6 17.4

KW 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 T.C. 21.9 24.6 24.1 27.3 29.5 24.5 26.0 25.5 28.6 31.1 27.0 27.4 26.9 30.0 32.6 S.C. 20.8 19.4 16.5 16.8 14.3 23.3 22.4 18.6 18.8 15.4 25.7 25.4 20.7 20.8 16.5

KW 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 T.C. 20.9 22.9 22.6 25.3 27.6 23.1 24.1 23.7 26.5 28.9 25.3 25.3 24.9 27.8 30.3 S.C. 19.9 18.6 15.8 16.0 13.4 22.0 21.2 17.9 18.0 14.5 24.1 23.7 20.0 20.0 15.6

KW 1.7 1.7 1.7 1.7 1.8 1.7 1.7 1.7 1.8 1.8 1.8 1.7 1.7 1.8 1.8 T.C. 19.8 21.1 21.0 23.4 25.6 21.7 22.1 22.0 24.5 26.8 23.5 23.1 23.0 25.6 27.9 S.C. 18.9 17.8 15.0 15.1 12.6 20.6 19.9 17.1 17.2 13.7 22.4 22.0 19.2 19.2 14.8

KW 1.8 1.8 1.8 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 T.C. 18.4 19.1 19.2 21.5 23.5 20.1 20.3 20.0 22.3 24.5 21.8 21.5 20.8 23.2 25.5 S.C. 17.6 16.7 14.3 14.4 11.7 19.2 18.6 16.2 16.4 12.8 20.8 20.5 18.1 18.4 13.9

KW 1.9 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.1 T.C. 17.1 17.3 17.4 19.6 21.5 18.6 18.6 18.0 20.2 22.3 20.1 20.0 18.7 20.9 23.1 S.C. 16.3 15.7 13.5 13.6 10.8 17.7 17.4 15.2 15.6 12.0 19.2 19.1 16.9 17.6 13.1

KW 2.1 2.1 2.1 2.1 2.2 2.1 2.1 2.1 2.1 2.2 2.2 2.2 2.1 2.2 2.2 T.C. 15.8 15.4 15.6 17.7 19.5 17.1 17.0 16.1 18.2 20.1 18.5 18.5 16.6 18.6 20.7 S.C. 15.0 14.7 12.7 12.9 10.0 16.3 16.1 14.3 14.9 11.1 17.6 17.6 15.8 16.9 12.2

KW 2.2 2.2 2.2 2.2 2.3 2.2 2.2 2.2 2.3 2.3 2.3 2.3 2.2 2.3 2.3

Furnaces Coils T.C. S.C. KW

T*9X*B12 FC/MC/PC35B 1.02 1.04 0.91 T*(8,L)X*A12 FC/MC/PC37A 1.05 1.10 0.91 T*(8,L)X*B12 FC/MC/PC43B 1.06 1.12 0.91 T*9X*B12 FC/MC/PC43B 1.04 1.07 0.91 T*(8,L)X*B12 FC/MC/PC35B 1.04 1.09 0.91 T*9X*C16 FC/MC/PC35C 1.00 1.00 0.90 T*(8,L)X*A12 FC/MC/PC32A 1.02 1.05 0.91

Y*(8,L)C*A12 FC/MC/PC32A 1.01 1.01 0.94 Y*(8,L)C*B12 FC/MC/PC35B 1.02 1.01 0.93

(Y*9C/T*9V)*B12 FC/MC/PC35B 1.03 1.03 0.94

Y*(8,L)C*A12 FC/MC/PC37A 1.03 1.04 0.95 Y*(8,L)C*B12 FC/MC/PC43B 1.03 1.02 0.93

(Y*9C/T*9V)*B12 FC/MC/PC43B 1.04 1.04 0.94

Y*(8,L)C*B12 HC36 1.02 1.00 0.93

(Y*9C/T*9V)*B12 HC36 1.03 1.03 0.94

Y*(8,L)C*A12 HD36 1.00 0.99 0.93 Y*(8,L)C*B12 HD36 1.00 0.96 0.93 Y*(8,L)C*C16 HD36 1.02 1.02 0.92 Y*(8,L)C*C20 HD36 1.00 0.96 0.91

(Y*9C/T*9V)*B12 HD36 1.00 0.99 0.93 (Y*9C/T*9V)*C16 HD36 1.00 1.00 0.92 (Y*9C/T*9V)*C20 HD36 1.00 0.96 0.92

Johnson Controls Unitary Products 21

Page 22

397855-YTG-G-0509

COOLING PERFORMANCE DATA

CONDENSING UNIT MODEL NO. YHJD30S41S1 INDOOR COIL MODEL NO. AHP36

CONDENSING

ENTERING AIR

TEMPERATURE

105

115

125

NOTE: ALL CAPACITIES INCLUDE INDOOR FAN HEAT AT 1250 BTUH/1000 CFM.

Multipliers for determining the performance with other indoor sections.

NOTE: For dry bulb temperatures different than those listed (between 73-87 F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the listed

temperature and decreases by 1060 BTUH per 1000 CFM per degree below the listed temperature.

IDCFM 800 1000 1200 ID DB (°F) 80 80 75 80 80 80 80 75 80 80 80 80 75 80 80 ID WB (°F) 57 62 62 67 72 57 62 62 67 72 57 62 62 67 72

T.C. 28.5 30.9 31.1 34.0 37.0 30.8 32.4 32.4 35.6 38.7 33.1 33.9 33.7 37.2 40.5

S.C. 28.5 26.1 22.3 22.1 18.6 30.8 29.7 24.5 24.4 19.8 33.1 33.4 26.8 26.7 21.1

KW 1.7 1.8 1.8 1.8 1.7 1.7 1.8 1.8 1.7 1.7 1.7 1.8 1.8 1.7 1.7

T.C. 27.1 29.1 29.1 32.0 35.3 29.2 30.3 30.3 33.4 36.6 31.3 31.5 31.5 34.7 37.9

S.C. 27.1 25.2 21.4 21.3 17.7 29.2 28.2 23.6 23.5 18.9 31.3 31.3 25.8 25.7 20.1

KW 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9

T.C. 25.7 27.2 27.2 30.0 33.6 27.6 28.2 28.2 31.2 34.5 29.5 29.2 29.2 32.3 35.4

S.C. 25.7 24.3 20.5 20.4 16.8 27.6 26.7 22.7 22.6 17.9 29.5 29.2 24.8 24.7 19.1

KW 2.0 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1

T.C. 24.3 25.3 25.3 28.1 31.8 26.0 26.1 26.1 29.0 32.3 27.7 26.8 27.0 29.9 32.9

S.C. 24.3 23.4 19.6 19.6 15.9 26.0 25.2 21.7 21.7 17.0 27.7 26.8 23.9 23.7 18.0

KW 2.2 2.2 2.2 2.3 2.3 2.2 2.2 2.2 2.3 2.3 2.3 2.3 2.3 2.3 2.3

T.C. 22.6 23.3 23.0 25.7 29.1 24.1 24.2 23.7 26.4 29.6 25.6 25.1 24.4 27.2 30.1

S.C. 22.6 22.1 18.6 18.6 14.9 24.1 23.7 20.5 20.7 16.0 25.6 25.1 22.4 22.7 17.1

KW 2.4 2.4 2.4 2.4 2.5 2.4 2.4 2.4 2.4 2.5 2.4 2.4 2.4 2.5 2.5

T.C. 21.0 21.3 20.9 23.4 26.4 22.3 22.3 21.3 24.0 26.9 23.6 23.4 21.8 24.5 27.4

S.C. 21.0 20.8 17.7 17.7 13.9 22.3 22.2 19.3 19.7 15.0 23.6 23.4 20.9 21.8 16.1

KW 2.5 2.5 2.5 2.6 2.7 2.6 2.6 2.5 2.6 2.7 2.6 2.6 2.6 2.6 2.7

T.C. 19.4 19.3 18.7 21.1 23.7 20.5 20.5 19.0 21.5 24.2 21.6 21.6 19.3 21.9 24.7

S.C. 19.4 19.3 16.7 16.8 12.9 20.5 20.5 18.1 18.8 14.1 21.6 21.6 19.3 20.8 15.2

KW 2.7 2.7 2.7 2.8 2.8 2.7 2.7 2.7 2.8 2.9 2.8 2.8 2.7 2.8 2.9

Air Handlers Coils T.C. S.C. KW

– FC/MC/PC32 0.99 0.99 1.00 – FC/MC/PC35 0.99 0.99 1.00 – FC/MC/PC37 1.01 1.01 1.00 – FC/MC/PC43 1.01 1.01 1.00 – HC36 0.99 0.99 1.00 – HC42 1.01 1.01 1.00 – HD48 1.01 1.01 1.00 AHP36 – 1.00 1.00 1.00 AHX36 – 1.03 1.06 0.91 AV36 – 1.04 1.05 1.00 F4FP040 – 0.99 0.97 1.00 F6FP036 – 1.01 1.01 0.93 MA12B FC/MC/PC35B 0.99 0.99 1.00 MV12B FC/MC/PC35B 1.01 1.01 1.00 MV16C FC/MC/PC35C 1.01 1.01 1.00 MA12B FC/MC/PC43B 1.01 1.01 1.00 MV12B FC/MC/PC43B 1.03 1.03 1.00 MV16C FC/MC/PC43C 1.03 1.03 1.00

Furnaces Coils T.C. S.C KW

T*(8,L)X*A12 FC/MC/PC37A 1.05 1.10 0.95 T*9X*B12 FC/MC/PC43B 1.05 1.10 0.94 T*(8,L)X*B12 FC/MC/PC43B 1.05 1.10 0.95

Y*(8,L)C*A12 FC/MC/PC37A 1.01 1.01 0.97 Y*(8,L)C*B12 FC/MC/PC43B 1.02 1.02 0.94

(Y*9C/T*9V)*B12 FC/MC/PC43B 1.01 1.02 0.96

Y*(8,L)C*C16 FC/MC/PC43C 1.03 1.03 0.93 Y*(8,L)C*C20 FC/MC/PC43C 1.02 1.04 0.92

(Y*9C/T*9V)*C16 FC/MC/PC43C 1.02 1.02 0.95 (Y*9C/T*9V)*C20 FC/MC/PC43C 1.02 1.03 0.93

Y*(8,L)C*C16 HC42 1.02 1.03 0.93 Y*(8,L)C*C20 HC42 1.02 1.03 0.92

(Y*9C/T*9V)*C16 HC42 1.02 1.02 0.95 (Y*9C/T*9V)*C20 HC42 1.02 1.03 0.93

Y*(8,L)C*A12 HD36 0.99 0.97 0.95 Y*(8,L)C*B12 HD36 0.99 0.97 0.93 Y*(8,L)C*C16 HD36 0.99 0.97 0.93 Y*(8,L)C*C20 HD36 1.00 1.00 0.93

(Y*9C/T*9V)*B12 HD36 0.99 0.97 0.94 (Y*9C/T*9V)*C16 HD36 0.99 0.97 0.93 (Y*9C/T*9V)*C20 HD36 0.99 0.97 0.93

22 Johnson Controls Unitary Products

Page 23

COOLING PERFORMANCE DATA

CONDENSING UNIT MODEL NO. YHJD36S41S1 INDOOR COIL MODEL NO. AHP36

CONDENSING

ENTERING AIR

TEMPERATURE

105

115

125

NOTE: ALL CAPACITIES I N CL UDE INDOO R FAN HEAT AT 1250 BTUH/1000 CFM.

Multipliers for determining the performance with other indoor sections.

NOTE: For dry bulb temperatures different than those listed (between 73-87 F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the listed

temperature and decreases by 1060 BTUH per 1000 CFM per degree below the listed temperature.

Air Handlers Coils T.C. S.C. KW

– FC/MC/PC37 1.00 0.99 1.00 – FC/MC/PC43 0.99 0.99 1.00 – FC/MC/PC48 1.00 1.00 1.00 – HC42 0.99 0.99 1.00 – HD48 1.00 1.00 1.00 – HD48 0.97 0.96 1.00 AV36 – 1.02 1.04 1.00 F4FP045 – 1.00 1.00 1.00 MA12B FC/MC/PC43B 0.99 0.99 1.00 MV12B FC/MC/PC43B 1.01 1.01 1.00 MV16C FC/MC/PC43C 1.01 1.01 1.00 MA14D FC/MC/PC48D 1.00 1.00 1.00 MV12D FC/MC/PC48D 1.01 1.00 1.00 MV16C FC/MC/PC48C 1.03 1.02 1.00 MV20D FC/MC/PC48D 1.03 1.02 1.00

Furnaces Coils T.C. S.C. KW

T*9X*B12 FC/MC/PC43B 1.04 1.07 0.96 T*(8,L)X*B12 FC/MC/PC43B 1.04 1.07 0.96 T*(8,L)X*C16 FC/MC/PC43C 1.04 1.05 0.92 T*9X*C16 FC/MC/PC43C 1.04 1.08 0.95 T*(8,L)X*C20 FC/MC/PC43C 1.05 1.08 0.94 T*9X*C20 FC/MC/PC43C 1.03 1.05 0.94

Y*(8,L)C*A12 FC/MC/PC37A 0.97 0.92 0.94

IDCFM 1000 1200 1400

ID DB (°F) 80 80 75 80 80 80 80 75 80 80 80 80 75 80 80

ID WB (°F) 57 62 62 67 72 57 62 62 67 72 57 62 62 67 72

T.C. 37.0 40.3 39.8 43.7 47.3 39.3 41.5 41.2 45.3 48.9 41.6 42.6 42.7 46.8 50.5 S.C. 35.7 32.2 27.3 27.6 23.6 37.9 35.0 29.4 29.4 24.6 40.2 37.8 31.4 31.3 25.6

KW 2.2 2.2 2.2 2.1 2.2 2.2 2.2 2.2 2.1 2.2 2.1 2.2 2.2 2.2 2.2 T.C. 35.3 37.9 37.5 41.4 44.9 37.5 39.0 38.7 42.7 46.3 39.7 40.2 40.0 44.1 47.8 S.C. 34.1 31.1 26.4 26.5 22.3 36.2 33.9 28.4 28.4 23.4 38.3 36.6 30.4 30.3 24.4

KW 2.4 2.4 2.4 2.4 2.4 2.4 2.4 2.4 2.4 2.4 2.4 2.4 2.4 2.4 2.4 T.C. 33.7 35.4 35.2 39.0 42.4 35.7 36.6 36.2 40.2 43.7 37.7 37.8 37.3 41.4 45.1 S.C. 32.5 30.1 25.4 25.5 21.1 34.5 32.7 27.4 27.4 22.2 36.4 35.4 29.3 29.2 23.2

KW 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 T.C. 32.1 33.0 32.9 36.6 39.9 33.9 34.2 33.8 37.7 41.1 35.7 35.4 34.6 38.7 42.4 S.C. 31.0 29.1 24.4 24.5 19.9 32.7 31.6 26.4 26.4 20.9 34.5 34.2 28.3 28.2 22.0

KW 2.7 2.8 2.8 2.8 2.8 2.8 2.8 2.8 2.8 2.9 2.8 2.8 2.8 2.8 2.9 T.C. 29.9 30.2 30.2 33.6 36.9 31.6 31.6 30.9 34.5 38.0 33.2 32.9 31.6 35.5 39.0 S.C. 28.9 27.4 23.3 23.3 18.7 30.5 29.6 25.2 25.2 19.7 32.0 31.8 27.1 27.0 20.7

KW 2.9 3.0 3.0 3.0 3.1 3.0 3.0 3.0 3.0 3.1 3.0 3.0 3.0 3.0 3.1 T.C. 27.8 27.6 27.5 30.7 34.0 29.3 29.1 28.1 31.5 34.9 30.8 30.5 28.7 32.3 35.8 S.C. 26.9 25.7 22.1 22.2 17.5 28.3 27.6 24.0 24.0 18.5 29.7 29.5 25.9 25.9 19.5

KW 3.1 3.1 3.1 3.2 3.3 3.2 3.2 3.2 3.2 3.3 3.2 3.2 3.2 3.3 3.3 T.C. 25.7 25.0 24.8 27.8 31.1 27.0 26.6 25.3 28.4 31.8 28.3 28.1 25.8 29.1 32.6 S.C. 24.8 24.1 21.0 21.0 16.4 26.1 25.6 22.9 22.9 17.4 27.3 27.2 24.7 24.7 18.4

KW 3.3 3.3 3.3 3.4 3.5 3.4 3.4 3.3 3.4 3.5 3.4 3.4 3.4 3.5 3.6

Furnaces Coils T.C. S.C. KW

Y*(8,L)C*B12 FC/MC/PC43B 1.01 1.02 0.98

(Y*9C/T*9V)*B12 FC/MC/PC43B 1.01 1.02 0.98

Y*(8,L)C*C16 FC/MC/PC43C 1.02 1.03 0.95 Y*(8,L)C*C20 FC/MC/PC43C 1.02 1.03 0.94

(Y*9C/T*9V)*C16 FC/MC/PC43C 1.01 1.02 0.97 (Y*9C/T*9V)*C20 FC/MC/PC43C 1.02 1.03 0.95

Y*(8,L)C*C16 FC/MC/PC48C 1.03 1.04 0.95 Y*(8,L)C*C20 FC/MC/PC48C 1.03 1.04 0.94

(Y*9C/T*9V)*C16 FC/MC/PC48C 1.03 1.04 0.96 (Y*9C/T*9V)*C20 FC/MC/PC48C 1.03 1.07 0.98

Y*(8,L)C*C16 HC42 1.01 1.03 0.95 Y*(8,L)C*C20 HC42 1.02 1.03 0.94

(Y*9C/T*9V)*C16 HC42 1.01 1.02 0.97 (Y*9C/T*9V)*C20 HC42 1.01 1.03 0.95

Y*(8,L)C*B12 HD48 1.00 1.01 0.97 Y*(8,L)C*C16 HD48 1.02 1.03 0.94 Y*(8,L)C*C20 HD48 1.03 1.03 0.94

(Y*9C/T*9V)*B12 HD48 1.00 1.01 0.97 (Y*9C/T*9V)*C16 HD48 1.02 1.02 0.95 (Y*9C/T*9V)*C20 HD48 1.02 1.06 0.98

Y*(8,L)C*C16 UC48C 1.02 1.04 0.95 Y*(8,L)C*C20 UC48C 1.03 1.05 0.94

(Y*9C/T*9V)*C16 UC48C 1.02 1.04 0.96 (Y*9C/T*9V)*C20 UC48C 1.03 1.08 0.98

Johnson Controls Unitary Products 23

Page 24

397855-YTG-G-0509

COOLING PERFORMANCE DATA

CONDENSING UNIT MODEL NO. YHJD42S41S1 INDOOR COIL MODEL NO. FC/MC/PC48

CONDENSING

ENTERING AIR

TEMPERATURE

105

115

125

NOTE: ALL CAPACITIES INCLUDE INDOOR FAN HEAT AT 1250 BTUH/1000 CFM.

Multipliers for determining the performance with other indoor sections.

NOTE: For dry bulb temperatures different than those listed (between 73-87 F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the listed

temperature and decreases by 1060 BTUH per 1000 CFM per degree below the listed temperature.

Air Handlers Coils T.C. S.C. KW

– FC/MC/PC60 0.99 0.99 1.00 – HC42 1.00 0.99 1.00 – HC60 0.99 0.99 1.00 – HD60 1.01 1.00 1.00 AHX42 – 1.01 1.07 0.95 AHX48 – 1.02 1.09 0.96 AV/SV*48 – 1.01 1.06 0.96 F4FP045 – 0.99 1.00 1.00 F5FP048 – 1.02 1.04 1.00 F6FP042 – 1.01 1.08 0.97 F6FP048 – 1.02 1.07 0.96 AHP/SHP48 – 1.00 1.00 1.00 MA14D FC/MC/PC48D 1.00 1.00 1.00 MA16C FC/MC/PC48C 1.00 1.00 1.00 MV16C FC/MC/PC48C 1.02 1.02 1.00 MV20D FC/MC/PC48D 1.02 1.02 1.00 MA14D FC/MC/PC60D 0.99 0.99 1.00 MA16C FC/MC/PC60C 0.99 0.99 1.00 MV20D FC/MC/PC60D 1.01 1.01 1.00

Continued on next page.

IDCFM 1200 1400 1600 ID DB (°F) 80 80 75 80 80 80 80 75 80 80 80 80 75 80 80 ID WB (°F) 57 62 62 67 72 57 62 62 67 72 57 62 62 67 72

T.C. 39.7 42.2 42.3 46.6 50.3 41.4 43.0 43.0 47.1 51.6 43.2 43.9 43.7 47.7 52.9

S.C. 39.7 37.8 32.1 32.0 25.7 41.4 41.1 34.2 33.9 27.1 43.2 43.9 36.3 35.8 28.4

KW 2.4 2.4 2.5 2.5 2.4 2.4 2.4 2.5 2.5 2.4 2.5 2.5 2.4 2.5 2.5

T.C. 38.3 40.2 40.3 44.3 48.1 39.9 41.0 41.0 44.9 49.1 41.6 41.9 41.7 45.6 50.2

S.C. 38.3 36.9 31.2 31.0 24.8 39.9 39.9 33.3 33.0 26.1 41.6 41.9 35.4 34.9 27.3

KW 2.7 2.7 2.7 2.7 2.7 2.7 2.7 2.7 2.7 2.7 2.7 2.7 2.7 2.7 2.7

T.C. 36.9 38.2 38.2 41.9 45.8 38.4 39.0 39.0 42.7 46.7 40.0 39.9 39.7 43.5 47.5

S.C. 36.9 36.0 30.2 30.0 23.9 38.4 38.6 32.3 32.0 25.1 40.0 39.9 34.5 34.1 26.2

KW 2.9 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0

T.C. 35.4 36.1 36.2 39.6 43.5 36.9 37.0 36.9 40.5 44.2 38.4 37.9 37.7 41.4 44.9

S.C. 35.4 35.1 29.2 29.0 23.0 36.9 37.0 31.4 31.1 24.1 38.4 37.9 33.5 33.2 25.1

KW 3.2 3.2 3.2 3.2 3.3 3.2 3.2 3.2 3.2 3.3 3.2 3.2 3.2 3.3 3.3

T.C. 33.2 33.7 33.4 36.7 40.2 34.5 34.6 34.1 37.4 40.8 35.9 35.5 34.8 38.1 41.4

S.C. 33.2 33.4 28.0 27.8 21.7 34.5 34.6 30.1 29.8 22.8 35.9 35.5 32.3 31.9 23.8

KW 3.6 3.6 3.6 3.6 3.7 3.6 3.6 3.6 3.6 3.7 3.6 3.6 3.6 3.7 3.7

T.C. 31.1 31.3 30.6 33.8 37.1 32.2 32.3 31.3 34.4 37.5 33.4 33.2 32.0 34.9 37.9

S.C. 31.1 31.3 26.8 26.6 20.4 32.2 32.3 28.9 28.6 21.5 33.4 33.2 31.0 30.6 22.6

KW 4.0 4.0 4.0 4.0 4.1 4.0 4.0 4.0 4.0 4.1 4.0 4.0 4.0 4.0 4.1

T.C. 28.9 28.9 27.9 31.0 33.9 29.9 29.9 28.5 31.4 34.2 30.9 30.9 29.2 31.7 34.5

S.C. 28.9 28.9 25.5 25.4 19.1 29.9 29.9 27.7 27.4 20.2 30.9 30.9 29.2 29.4 21.3

KW 4.5 4.4 4.4 4.4 4.5 4.4 4.4 4.4 4.4 4.5 4.4 4.4 4.4 4.4 4.5

24 Johnson Controls Unitary Products

Page 25

Furnaces Coils T.C. S.C. KW

T*(8,L)X*C16 FC/MC/PC48C 1.00 1.05 0.95 T*9X*C16 FC/MC/PC48C 1.01 1.07 0.97 T*(8,L)X*C20 FC/MC/PC48C 1.02 1.09 0.96 T*9X*C20 FC/MC/PC48C 1.01 1.07 0.96 T*9X*D20 FC/MC/PC48D 1.01 1.07 0.96 T*(8,L)X*C16 UC48C 1.02 1.08 0.94 T*9X*C16 UC48C 1.01 1.07 0.97 T*(8,L)X*C20 UC48C 1.02 1.11 0.96 T*9X*C20 UC48C 1.02 1.07 0.96 T*9X*D20 UC48D 1.01 1.08 0.96

Y*(8,L)C*C16 FC/MC/PC48C 1.02 1.03 0.96 Y*(8,L)C*C20 FC/MC/PC48C 1.02 1.04 0.96

(Y*9C/T*9V)*C16 FC/MC/PC48C 1.01 1.03 0.97 (Y*9C/T*9V)*C20 FC/MC/PC48C 1.01 1.03 0.98 (Y*9C/T*9V)*D20 FC/MC/PC48D 1.02 1.03 0.97 (Y*9C/T*9V)*D20 FC/MC/PC60D 1.02 1.04 0.96 (Y*9C/T*9V)*D20 FC/MC62D 1.02 1.05 0.96

Y*(8,L)C*C16 FC/PC60C 1.02 1.04 0.95 Y*(8,L)C*C20 FC/PC60C 1.02 1.04 0.94

(Y*9C/T*9V)*C16 FC/PC60C 1.02 1.03 0.98 (Y*9C/T*9V)*C20 FC/PC60C 1.02 1.04 0.97

Furnaces Coils T.C. S.C. KW

Y*(8,L)C*C16 HC42 1.01 1.02 0.96 Y*(8,L)C*C20 HC42 1.01 1.02 0.96

(Y*9C/T*9V)*C16 HC42 1.01 1.01 0.97 (Y*9C/T*9V)*C20 HC42 1.01 1.01 0.97

Y*(8,L)C*B12 HD48 1.00 0.97 0.98 Y*(8,L)C*C16 HD48 0.99 1.00 0.96 Y*(8,L)C*C20 HD48 1.00 0.98 0.95

(Y*9C/T*9V)*B12 HD48 0.95 0.90 0.95 (Y*9C/T*9V)*C16 HD48 1.00 0.98 0.97 (Y*9C/T*9V)*C20 HD48 1.01 1.01 0.97 (Y*9C/T*9V)*D20 HD48 1.00 1.01 0.96

Y*(8,L)C*C16 UC48C 1.01 1.02 0.96 Y*(8,L)C*C20 UC48C 1.01 1.03 0.95

(Y*9C/T*9V)*C16 UC48C 1.01 1.02 0.97 (Y*9C/T*9V)*C20 UC48C 1.01 1.02 0.97 (Y*9C/T*9V)*D20 UC48D 1.01 1.02 0.96

Y*(8,L)C*C16 UC60C 1.01 1.02 0.95 Y*(8,L)C*C20 UC60C 1.02 1.02 0.94

(Y*9C/T*9V)*C16 UC60C 1.00 1.01 0.98 (Y*9C/T*9V)*C20 UC60C 1.01 1.01 0.97 (Y*9C/T*9V)*D20 UC60D 1.01 1.01 0.96

Johnson Controls Unitary Products 25

Page 26

397855-YTG-G-0509

COOLING PERFORMANCE DATA

CONDENSING UNIT MODEL NO. YHJD48S41S1 INDOOR COIL MODEL NO. AHP/SHP48

CONDENSING

ENTERING AIR

TEMPERATURE

105

115

125

NOTE: ALL CAPACITIES INCLUDE INDOOR FAN HEAT AT 1250 BTUH/1000 CFM.

Multipliers for determining the performance with other indoor sections.

NOTE: For dry bulb temperatures different than those listed (between 73-87 F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the listed

temperature and decreases by 1060 BTUH per 1000 CFM per degree below the listed temperature.

Air Handlers Coils T.C. S.C. KW

– FC/MC/PC48 1.00 1.01 1.00 – FC/MC/PC60 1.00 1.02 1.00 – HC60 1.00 1.02 1.00 – HD60 1.00 1.01 1.00 – MC62 1.01 1.02 1.00 AHP60 – 1.01 1.03 1.00 AHX48 – 1.04 1.08 0.98 AV/SV*48 – 1.02 1.03 1.00 AV/SV*60 – 1.03 1.03 0.96 F4FV060 – 1.02 1.03 1.00 F5FP048 – 1.02 1.05 1.00 F5FP060 – 1.02 1.05 1.00 F6FP048 – 1.05 1.07 0.98 MA16C FC/MC/PC48C 1.00 1.01 1.00 MA20D FC/MC/PC48D 1.00 1.01 1.00 MV16C FC/MC/PC48C 1.02 1.02 1.00 MV20D FC/MC/PC48D 1.01 1.02 1.00 MA16C FC/MC/PC60C 1.00 1.02 1.00 MA20D FC/MC/PC60D 1.00 1.02 1.00 MV20D FC/MC/PC60D 1.01 1.03 1.00 MA20D MC62D 1.01 1.02 1.00 MV20D MC62D 1.02 1.03 1.00

Furnaces Coils T.C. S.C. KW

T*(8,L)X*C16 FC/PC60C 1.03 1.04 0.98 T*9X*C16 FC/PC60C 1.03 1.04 0.99 T*(8,L)X*C20 FC/MC/PC60D 1.03 1.04 0.98

IDCFM 1400 1600 1800 ID DB (°F) 80 80 75 80 80 80 80 75 80 80 80 80 75 80 80 ID WB (°F) 57 62 62 67 72 57 62 62 67 72 57 62 62 67 72

T.C. 46.3 49.0 49.0 53.3 57.3 48.3 49.9 49.7 54.0 58.4 50.2 50.8 50.4 54.8 59.4

S.C. 46.3 43.0 36.2 35.8 29.6 48.3 45.5 37.9 37.6 30.7 50.2 48.0 39.6 39.4 31.8

KW 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5

T.C. 44.6 46.6 46.6 50.7 54.8 46.3 47.5 47.3 51.6 55.7 47.9 48.4 48.0 52.4 56.7

S.C. 44.6 41.9 35.2 34.8 28.3 46.3 44.4 37.0 36.6 29.4 47.9 46.9 38.8 38.4 30.5

KW 2.9 2.8 2.8 2.9 2.9 2.9 2.8 2.8 2.9 2.9 2.8 2.8 2.8 2.9 2.9

T.C. 42.9 44.1 44.2 48.2 52.2 44.3 45.0 44.9 49.1 53.1 45.7 45.9 45.7 50.0 54.0

S.C. 42.9 40.9 34.3 33.8 27.1 44.3 43.3 36.1 35.7 28.1 45.7 45.7 38.0 37.5 29.1

KW 3.2 3.2 3.2 3.2 3.2 3.2 3.2 3.2 3.2 3.2 3.2 3.2 3.2 3.2 3.2

T.C. 41.1 41.7 41.7 45.7 49.7 42.3 42.6 42.5 46.6 50.5 43.4 43.5 43.3 47.5 51.3

S.C. 41.1 39.8 33.3 32.8 25.8 42.3 42.2 35.2 34.7 26.8 43.4 43.5 37.2 36.6 27.8

KW 3.5 3.5 3.5 3.6 3.6 3.5 3.5 3.5 3.6 3.6 3.5 3.5 3.5 3.6 3.6

T.C. 38.8 38.7 38.7 42.4 46.4 39.8 39.8 39.4 43.2 47.0 40.9 40.8 40.0 43.9 47.6

S.C. 38.8 37.7 32.0 31.6 24.6 39.8 39.7 33.9 33.5 25.6 40.9 40.8 35.9 35.3 26.6

KW 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0

T.C. 36.4 35.9 35.9 39.3 43.3 37.5 37.0 36.3 39.8 43.7 38.5 38.1 36.8 40.4 44.1

S.C. 36.4 35.7 30.7 30.4 23.4 37.5 37.0 32.7 32.2 24.3 38.5 38.1 34.6 34.1 25.3

KW 4.4 4.4 4.4 4.4 4.5 4.4 4.4 4.4 4.4 4.5 4.4 4.4 4.4 4.4 4.5

T.C. 34.1 33.0 33.0 36.1 40.1 35.1 34.2 33.3 36.5 40.4 36.0 35.4 33.6 36.9 40.6

S.C. 34.1 33.0 29.5 29.2 22.1 35.1 34.2 31.4 31.0 23.1 36.0 35.4 33.3 32.9 24.1

KW 4.8 4.8 4.8 4.8 4.9 4.8 4.8 4.8 4.9 4.9 4.8 4.8 4.8 4.9 4.9

Furnaces Coils T.C. S.C. KW

T*9X*C20 FC/PC60C 1.03 1.04 0.98 T*9X*D20 FC/MC/PC60D 1.02 1.02 0.94 T*9X*D20 FC/MC62D 1.03 1.06 0.99 T*(8,L)X*C16 UC60C 1.02 1.04 0.98 T*(8,L)X*C20 UC60D 1.02 1.03 0.94 T*9X*C16 UC60C 1.02 1.04 0.99 T*9X*C20 UC60C 1.03 1.04 0.98 T*9X*D20 UC60D 1.02 1.01 0.94 (Y*9C/T*9V)*D20 FC/MC/PC60D 1.00 1.02 0.98 (Y*9C/T*9V)*D20 FC/MC62D 1.00 1.03 0.98

Y*(8,L)C*C16 FC/PC60C 1.00 1.03 0.98 Y*(8,L)C*C20 FC/PC60C 1.01 1.03 0.96

(Y*9C/T*9V)*C16 FC/PC60C 1.00 1.02 0.99 (Y*9C/T*9V)*C20 FC/PC60C 1.00 1.02 0.99 (Y*9C/T*9V)*D20 HC60 0.99 1.02 0.98

Y*(8,L)C*C16 HD60 1.00 1.03 0.98 Y*(8,L)C*C20 HD60 1.01 1.03 0.96

(Y*9C/T*9V)*C16 HD60 1.00 1.03 0.99 (Y*9C/T*9V)*C20 HD60 1.00 1.03 0.99 (Y*9C/T*9V)*D20 HD60 1.00 1.03 0.98

Y*(8,L)C*C16 UC60C 0.99 1.00 0.98 Y*(8,L)C*C20 UC60C 0.99 1.01 0.96

(Y*9C/T*9V)*C16 UC60C 0.98 1.00 0.99 (Y*9C/T*9V)*C20 UC60C 0.98 1.00 0.99 (Y*9C/T*9V)*D20 UC60D 0.99 1.00 0.98

26 Johnson Controls Unitary Products

Page 27

COOLING PERFORMANCE DATA

CONDENSING UNIT MODEL NO. YHJD60S41S1 INDOOR COIL MODEL NO. FC/MC62

CONDENSING

ENTERING AIR

TEMPERATURE

105

115

125

NOTE: ALL CAPACITIES I N CL UDE INDOO R FAN HEAT AT 1250 BTUH/1000 CFM.

Multipliers for determining the performance with other indoor sections.

NOTE: For dry bulb temperatures different than those listed (between 73-87 F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the listed

temperature and decreases by 1060 BTUH per 1000 CFM per degree below the listed temperature.

Air Handlers Coils T.C. S.C. KW

AHX60 – 1.06 1.13 1.05 F6FP060 – 1.06 1.09 1.01 MA20D MC62D 1.00 1.00 1.00 MV20D MC62D 1.01 1.01 1.00

IDCFM 1600 1800 2000

ID DB (°F) 80 80 75 80 80 80 80 75 80 80 80 80 75 80 80

ID WB (°F) 57 62 62 67 72 57 62 62 67 72 57 62 62 67 72

T.C. 54.0 57.1 56.9 62.3 67.6 56.0 57.9 57.8 63.4 69.1 58.0 58.7 58.7 64.4 70.5 S.C. 54.0 51.0 43.4 42.9 34.8 56.0 54.4 45.4 45.0 36.2 58.0 57.7 47.4 47.1 37.6

KW 2.8 2.8 2.8 2.9 2.9 2.8 2.8 2.8 2.9 2.9 2.8 2.8 2.8 2.9 2.9 T.C. 51.9 54.1 53.9 59.2 64.5 53.7 54.9 54.8 60.2 65.7 55.5 55.7 55.6 61.2 66.9 S.C. 51.9 49.8 42.0 41.7 33.5 53.7 52.7 44.1 43.8 34.8 55.5 55.6 46.1 45.8 36.2

KW 3.2 3.2 3.2 3.3 3.3 3.2 3.2 3.2 3.3 3.3 3.2 3.2 3.2 3.3 3.3 T.C. 49.7 51.1 51.0 56.2 61.4 51.3 51.9 51.8 57.1 62.4 53.0 52.7 52.6 58.0 63.4 S.C. 49.7 48.6 40.7 40.5 32.2 51.3 51.1 42.8 42.5 33.4 53.0 52.7 44.9 44.6 34.7

KW 3.6 3.6 3.6 3.6 3.7 3.6 3.6 3.6 3.7 3.7 3.6 3.6 3.6 3.7 3.7 T.C. 47.6 48.1 48.1 53.1 58.3 49.0 48.9 48.8 54.0 59.0 50.4 49.7 49.5 54.8 59.8 S.C. 47.6 47.4 39.3 39.2 30.9 49.0 48.9 41.5 41.3 32.0 50.4 49.7 43.6 43.3 33.2

KW 4.0 4.0 4.0 4.0 4.1 4.0 4.0 4.0 4.1 4.1 4.0 4.0 4.0 4.1 4.1 T.C. 44.3 44.6 44.1 48.7 53.5 45.6 45.5 44.6 49.3 54.1 46.8 46.3 45.2 50.0 54.7 S.C. 44.3 44.6 37.6 37.4 29.0 45.6 45.5 39.7 39.4 30.2 46.8 46.3 41.8 41.5 31.3

KW 4.5 4.5 4.5 4.5 4.6 4.5 4.5 4.5 4.5 4.6 4.5 4.5 4.5 4.5 4.6 T.C. 41.1 41.3 40.2 44.4 48.9 42.2 42.2 40.6 44.9 49.4 43.3 43.1 41.0 45.3 49.9 S.C. 41.1 41.3 35.9 35.7 27.3 42.2 42.2 37.9 37.7 28.4 43.3 43.1 40.0 39.7 29.5

KW 4.9 5.0 4.9 5.0 5.0 5.0 5.0 4.9 5.0 5.0 5.0 5.0 5.0 5.0 5.0 T.C. 37.9 37.9 36.2 40.1 44.3 38.8 38.8 36.5 40.4 44.6 39.8 39.8 36.8 40.7 45.0 S.C. 37.9 37.9 34.2 33.9 25.5 38.8 38.8 36.2 35.9 26.6 39.8 39.8 36.8 37.9 27.7

KW 5.4 5.4 5.4 5.4 5.5 5.4 5.4 5.4 5.4 5.5 5.4 5.4 5.4 5.4 5.5

Furnaces Coils T.C. S.C. KW

T*(8,L)X*C20 FC/MC62D 1.05 1.08 0.99 T*9X*D20 FC/MC62D 1.02 1.02 1.02 (Y*9C/T*9V)*D20 FC/MC/PC60D 0.99 0.96 0.97

Y*(8,L)C*C20 FC/MC62D 1.00 0.97 0.96

(Y*9C/T*9V)*C20 FC/MC62D 0.99 0.96 0.98

Johnson Controls Unitary Products 27

Page 28

397855-YTG-G-0509

HEATING PERFORMANCE DATA

CONDENSING UNIT MODEL NO YHJD18S41S1 EVAPORATOR COIL MODEL NO AHP18

AIR TEMP.

ENTERING

OUTDOOR UNIT

NOTE: ALL CAPACITIES ARE NET (KBTUH) WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM.

AIR TEMP.

ENTERING

INDOOR COIL

60 19.7 1.6 3.7 21.0 1.6 3.9 22.3 1.6 4.2 70 18.3 1.6 3.3 19.6 1.6 3.5 20.9 1.6 3.8 80 16.8 1.7 2.9 18.1 1.7 3.2 19.5 1.7 3.4 60 16.4 1.5 3.3 17.6 1.5 3.5 18.8 1.5 3.7 70 15.2 1.5 3.0 16.4 1.5 3.2 17.6 1.5 3.3 80 14.0 1.5 2.7 15.2 1.6 2.8 16.4 1.6 3.0 60 14.9 1.4 3.1 16.2 1.4 3.3 17.5 1.5 3.5 70 12.4 1.4 2.5 14.3 1.5 2.9 16.3 1.5 3.2 80 9.9 1.5 2.0 12.5 1.5 2.4 15.0 1.6 2.8 60 10.3 1.3 2.2 11.5 1.4 2.4 12.7 1.5 2.5 70 11.5 1.3 2.5 12.7 1.4 2.7 14.0 1.4 2.9 80 12.6 1.3 2.8 13.9 1.4 3.0 15.2 1.4 3.2 60 7.6 1.2 1.9 7.8 1.3 1.8 7.9 1.4 1.7 70 8.2 1.2 2.0 8.5 1.3 2.0 8.8 1.3 2.0 80 8.8 1.2 2.2 9.2 1.2 2.2 9.7 1.3 2.2 60 6.1 1.1 1.6 6.7 1.2 1.6 7.3 1.3 1.7 70 6.2 1.1 1.6 7.1 1.2 1.7 8.0 1.3 1.8 80 6.2 1.1 1.6 7.4 1.2 1.8 8.6 1.3 2.0

MBTUH KW C.O.P. MBTUH KW C.O.P. MBTUH KW C.O.P.

450 600 750

ID CFM

Multipliers for determining the performance with other indoor sections.

Air Handlers Coils MBH KW COP

– FC/MC/PC18 1.00 1.00 1.00 – FC/MC/PC24 1.03 1.04 0.99 – HC18 1.00 1.00 1.00 – HC30 1.02 1.02 0.99 – HD24 0.97 0.96 1.02 AHP18 – 1.02 1.02 1.00 AV24 – 0.98 0.99 1.00 F4FP024 – 1.01 1.01 1.00 MV12B FC/MC/PC18B 0.98 0.98 1.00 MA08B FC/MC/PC18B 1.00 1.00 1.00 MA08B FC/MC/PC24B 1.03 1.04 0.99 MV12B FC/MC/PC24B 1.00 1.02 0.99

Furnaces Coils MBH KW COP

Y*(8,L)C*A12 FC/MC/PC18A 0.98 1.07 0.92 Y*(8,L)C*B12 FC/MC/PC18B 0.97 1.06 0.92

(Y*9C/T*9V)*B12 FC/MC/PC18B 0.98 1.07 0.92

Y*(8,L)C*A12 FC/MC/PC24A 1.01 1.10 0.92 Y*(8,L)C*B12 FC/MC/PC24B 0.99 1.10 0.90

(Y*9C/T*9V)*B12 FC/MC/PC24B 1.01 1.11 0.91

Y*(8,L)C*A12 FC/MC/PC30A 1.01 1.10 0.92 Y*(8,L)C*B12 FC/MC/PC30B 0.99 1.10 0.90

(Y*9C/T*9V)*B12 FC/MC/PC30B 1.01 1.11 0.91

Y*(8,L)C*A12 HC18 0.98 1.07 0.92 Y*(8,L)C*A12 HC30 0.99 1.07 0.93 Y*(8,L)C*A12 HD24 0.98 1.06 0.93 Y*(8,L)C*B12 HD24 0.96 1.04 0.92

(Y*9C/T*9V)*B12 HD24 0.98 1.07 0.92

Y*(8,L)C*A12 UC18A 0.99 1.08 0.92 Y*(8,L)C*B12 UC18B 0.98 1.07 0.92

(Y*9C/T*9V)*B12 UC18B 0.99 1.08 0.91

Y*(8,L)C*A12 UC24A 1.02 1.11 0.91 Y*(8,L)C*B12 UC24B 0.99 1.10 0.90

(Y*9C/T*9V)*B12 UC24B 1.01 1.12 0.91

Y*(8,L)C*A12 UC30A 1.01 1.11 0.91 Y*(8,L)C*B12 UC30B 0.99 1.10 0.90

(Y*9C/T*9V)*B12 UC30B 1.01 1.12 0.91

28 Johnson Controls Unitary Products

Page 29

HEATING PERFORMANCE DATA

CONDENSING UNIT MODEL NO YHJD24S41S1 EVAPORATOR COIL MODEL NO AHP24

AIR TEMP.

ENTERING

OUTDOOR UNIT

NOTE: ALL CAPACITIES ARE NET (KBTUH) WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM.

AIR TEMP.

ENTERING

INDOOR COIL

60 28.4 2.1 4.0 30.1 2.0 4.3 31.8 2.0 4.6 70 26.7 2.2 3.6 28.4 2.2 3.9 30.1 2.1 4.1 80 25.1 2.3 3.2 26.8 2.3 3.5 28.5 2.2 3.7 60 23.4 1.9 3.5 24.5 1.9 3.7 25.7 1.9 3.9 70 22.0 2.0 3.2 22.2 2.0 3.3 22.4 2.0 3.3 80 20.6 2.1 2.9 19.9 2.0 2.9 19.1 2.0 2.8 60 20.7 1.9 3.2 21.9 1.9 3.4 23.1 1.9 3.5 70 19.3 1.9 2.9 20.4 2.0 3.1 21.6 2.0 3.2 80 17.9 2.0 2.7 19.0 2.0 2.8 20.0 2.1 2.9 60 17.2 1.7 2.9 18.1 1.8 3.0 19.0 1.8 3.0 70 15.8 1.8 2.6 16.7 1.8 2.7 17.6 1.9 2.7 80 14.3 1.8 2.3 15.2 1.9 2.4 16.2 1.9 2.5 60 7.9 1.6 1.5 11.2 1.6 2.0 14.4 1.7 2.5 70 9.0 1.6 1.7 11.0 1.7 1.9 13.0 1.7 2.2 80 10.0 1.6 1.8 10.9 1.7 1.9 11.7 1.7 2.0 60 10.5 1.5 2.1 11.2 1.6 2.1 11.9 1.6 2.1 70 9.3 1.5 1.8 9.9 1.6 1.9 10.6 1.6 1.9 80 8.0 1.5 1.6 8.6 1.6 1.6 9.3 1.6 1.7

MBTUH KW C.O.P. MBTUH KW C.O.P. MBTUH KW C.O.P.

600 800 1000

ID CFM

Multipliers for determining the performance with other indoor sections.

Air Handlers Coils MBH KW COP

– FC/MC/PC24 1.00 1.00 1.00 – FC/MC/PC30 1.00 1.00 1.00 – FC/MC/PC32 1.00 1.00 1.00 – FC/MC/PC35 1.00 1.00 1.00 – HC30 0.99 0.99 1.01 – HC36 1.00 1.00 1.00 – HD36 1.35 1.41 0.96 AHP30 – 1.01 1.01 1.00 AHX30 – 0.99 1.07 0.92 AHX36 – 0.99 1.12 0.89 AV24 – 0.96 0.95 1.01 AV*36 – 0.97 1.08 0.90 F4FP030 – 0.99 0.99 1.01 F6FP030 – 0.99 1.05 0.94 F6FP036 – 0.99 1.07 0.92 MA08B FC/MC/PC24B 1.00 1.00 1.00 MV12B FC/MC/PC24B 0.98 0.98 1.00 MA08B FC/MC/PC30B 1.00 1.00 1.00 MV12B FC/MC/PC30B 0.98 0.98 1.00 MA08B FC/MC/PC35B 1.00 1.00 1.00 MV12B FC/MC/PC35B 0.98 0.98 1.00 MV16C FC/MC/PC35C 0.98 0.98 1.00

Furnaces Coils MBH KW COP

T*9X*B12 FC/MC/PC35B 0.98 1.08 0.91 T*(8,L)X*A12 FC/MC/PC37A 1.00 1.12 0.89 T*(8,L)X*B12 FC/MC/PC43B 1.00 1.13 0.89 T*9X*B12 FC/MC/PC43B 0.99 1.11 0.90 T*(8,L)X*B12 FC/MC/PC35B 0.99 1.10 0.90 T*9X*C16 FC/MC/PC35C 0.96 1.06 0.90 T*(8,L)X*A12 FC/MC/PC32A 0.98 1.08 0.90

Y*(8,L)C*A12 FC/MC/PC32A 0.98 1.04 0.95 Y*(8,L)C*B12 FC/MC/PC35B 0.98 1.05 0.93

(Y*9C/T*9V)*B12 FC/MC/PC35B 0.99 1.05 0.94

Y*(8,L)C*A12 FC/MC/PC37A 1.00 1.07 0.93 Y*(8,L)C*B12 FC/MC/PC43B 0.98 1.07 0.92

(Y*9C/T*9V)*B12 FC/MC/PC43B 0.99 1.07 0.93

Y*(8,L)C*B12 HC36 0.97 1.05 0.93

(Y*9C/T*9V)*B12 HC36 0.99 1.05 0.94

Y*(8,L)C*A12 HD36 0.90 0.90 1.00 Y*(8,L)C*B12 HD36 0.89 0.89 1.00 Y*(8,L)C*C16 HD36 0.91 0.93 0.98 Y*(8,L)C*C20 HD36 0.88 0.89 0.98

(Y*9C/T*9V)*B12 HD36 0.90 0.90 1.00 (Y*9C/T*9V)*C16 HD36 0.90 0.91 0.99 (Y*9C/T*9V)*C20 HD36 0.88 0.89 0.99

Johnson Controls Unitary Products 29

Page 30

397855-YTG-G-0509

HEATING PERFORMANCE DATA

CONDENSING UNIT MODEL NO YHJD30S41S1 EVAPORATOR COIL MODEL NO AHP36

AIR TEMP.

ENTERING

OUTDOOR UNIT

NOTE: ALL CAPACITIES ARE NET (KBTUH) WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM.

AIR TEMP.

ENTERING

INDOOR COIL

60 33.0 2.5 3.9 35.7 2.4 4.3 38.5 2.4 4.7 70 31.4 2.6 3.6 34.1 2.6 3.9 36.9 2.6 4.2 80 29.8 2.7 3.2 32.5 2.7 3.5 35.2 2.7 3.8 60 28.8 2.3 3.6 30.6 2.3 3.9 32.3 2.3 4.1 70 26.6 2.4 3.2 28.3 2.4 3.4 29.9 2.4 3.6 80 24.4 2.5 2.9 26.0 2.5 3.0 27.6 2.5 3.2 60 25.8 2.2 3.4 27.1 2.3 3.5 28.4 2.3 3.7 70 24.2 2.3 3.0 25.4 2.3 3.2 26.6 2.4 3.3 80 22.6 2.4 2.7 23.7 2.4 2.8 24.7 2.5 2.9 60 19.3 2.3 2.5 19.9 2.3 2.5 20.4 2.4 2.5 70 20.8 2.2 2.7 21.5 2.3 2.8 22.2 2.3 2.9 80 22.3 2.2 3.0 23.1 2.2 3.1 24.0 2.2 3.2 60 13.3 2.1 1.9 14.8 2.1 2.0 16.3 2.2 2.2 70 15.4 2.1 2.2 16.5 2.1 2.3 17.7 2.1 2.4 80 17.4 2.0 2.5 18.2 2.1 2.6 19.0 2.1 2.7 60 13.0 2.0 1.9 10.0 2.1 1.4 6.9 2.1 1.0 70 14.5 2.0 2.1 13.4 2.0 1.9 12.2 2.1 1.7 80 16.0 2.0 2.4 16.7 2.0 2.5 17.5 2.0 2.5

MBTUH KW C.O.P. MBTUH KW C.O.P. MBTUH KW C.O.P.

800 1000 1200

Multipliers for determining the performance with other indoor sections.

ID CFM

Air Handlers Coils MBH KW COP

– FC/MC/PC32 0.99 0.98 1.01 – FC/MC/PC35 0.99 0.98 1.01 – FC/MC/PC37 1.00 1.00 1.00 – FC/MC/PC43 1.00 1.00 1.00 – HC36 0.99 0.98 1.01 – HC42 1.00 1.00 1.00 – HD48 1.34 1.40 0.96 AHP36 – 1.00 1.00 1.00 AHX36 – 0.98 1.08 0.90 AV36 – 0.98 0.98 1.00 F4FP040 – 0.99 0.98 1.02 F6FP036 – 0.97 1.03 0.94 MA12B FC/MC/PC35B 0.99 0.98 1.01 MV12B FC/MC/PC35B 0.97 0.96 1.01 MV16C FC/MC/PC35C 0.97 0.96 1.01 MA12B FC/MC/PC43B 1.00 1.00 1.00 MV12B FC/MC/PC43B 0.98 0.98 1.00 MV16C FC/MC/PC43C 0.98 0.98 1.00

Furnaces Coils MBH KW COP

T*(8,L)X*A12 FC/MC/PC37A 1.00 1.08 0.92 T*9X*B12 FC/MC/PC43B 1.00 1.09 0.92 T*(8,L)X*B12 FC/MC/PC43B 1.00 1.08 0.93

Y*(8,L)C*A12 FC/MC/PC37A 0.99 1.02 0.97 Y*(8,L)C*B12 FC/MC/PC43B 0.98 1.05 0.94

(Y*9C/T*9V)*B12 FC/MC/PC43B 0.99 1.03 0.96

Y*(8,L)C*C16 FC/MC/PC43C 0.98 1.06 0.92 Y*(8,L)C*C20 FC/MC/PC43C 0.98 1.07 0.92

(Y*9C/T*9V)*C16 FC/MC/PC43C 0.98 1.04 0.94 (Y*9C/T*9V)*C20 FC/MC/PC43C 0.98 1.06 0.93

Y*(8,L)C*C16 HC42 0.98 1.06 0.92 Y*(8,L)C*C20 HC42 0.98 1.07 0.92

(Y*9C/T*9V)*C16 HC42 0.98 1.04 0.94 (Y*9C/T*9V)*C20 HC42 0.98 1.06 0.93

Y*(8,L)C*A12 HD36 0.93 0.90 1.02 Y*(8,L)C*B12 HD36 0.92 0.92 1.01 Y*(8,L)C*C16 HD36 0.92 0.92 1.00 Y*(8,L)C*C20 HD36 0.93 0.94 0.99

(Y*9C/T*9V)*B12 HD36 0.92 0.91 1.01 (Y*9C/T*9V)*C16 HD36 0.92 0.92 1.00 (Y*9C/T*9V)*C20 HD36 0.92 0.92 1.01

30 Johnson Controls Unitary Products

Page 31

HEATING PERFORMANCE DATA

CONDENSING UNIT MODEL NO YHJD36S41S1 EVAPORATOR COIL MODEL NO AHP36

AIR TEMP.

ENTERING

OUTDOOR UNIT

NOTE: ALL CAPACITIES ARE NET (KBTUH) WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM.

AIR TEMP.

ENTERING

INDOOR COIL

60 44.9 3.1 4.2 46.3 3.2 4.3 47.8 3.2 4.4 70 42.7 3.3 3.8 44.3 3.3 3.9 45.8 3.4 4.0 80 40.6 3.4 3.5 42.2 3.5 3.6 43.9 3.5 3.6 60 36.8 2.9 3.7 38.6 3.0 3.8 40.5 3.0 3.9 70 28.4 2.8 3.0 33.4 3.0 3.3 38.5 3.2 3.5 80 19.9 2.7 2.2 28.2 3.0 2.7 36.5 3.3 3.2 60 34.6 2.8 3.6 35.2 2.9 3.6 35.8 3.0 3.5 70 24.0 3.0 2.4 32.5 3.0 3.2 41.1 3.1 3.9 80 13.3 3.1 1.3 29.8 3.1 2.8 46.3 3.2 4.3 60 28.1 2.7 3.1 29.7 2.8 3.2 31.3 2.8 3.2 70 25.2 2.8 2.7 27.3 2.9 2.8 29.4 2.9 2.9 80 22.4 2.9 2.3 24.9 3.0 2.5 27.5 3.0 2.7 60 22.2 2.4 2.7 23.1 2.5 2.7 24.0 2.7 2.6 70 21.0 2.5 2.5 21.6 2.6 2.4 22.2 2.7 2.4 80 19.8 2.6 2.3 20.1 2.7 2.2 20.3 2.8 2.2 60 19.7 2.4 2.4 20.7 2.5 2.5 21.8 2.6 2.5 70 15.0 2.4 1.8 17.5 2.5 2.1 20.1 2.6 2.2 80 10.3 2.4 1.3 14.4 2.5 1.7 18.4 2.7 2.0

MBTUH KW C.O.P. MBTUH KW C.O.P. MBTUH KW C.O.P.

1000 1200 1400

ID CFM

Multipliers for determining the performance with other indoor sections.

Air Handlers Coils MBH KW COP

– FC/MC/PC37 1.01 1.01 1.00 – FC/MC/PC43 1.01 1.01 1.00 – FC/MC/PC48 1.01 1.01 1.00 – HC42 1.01 1.01 1.00 – HD48 0.96 0.91 1.06 – HD48 0.96 0.90 1.07 AHX36 – 0.99 1.07 0.92 AV*36 – 0.99 1.06 0.93 F4FP045 – 1.03 1.06 0.97 F6FP042 – 1.02 1.09 0.94 MA12B FC/MC/PC43B 1.01 1.01 1.00 MV12B FC/MC/PC43B 1.00 1.00 1.00 MV16C FC/MC/PC43C 0.99 0.99 1.00 MA14D FC/MC/PC48D 1.01 1.01 1.00 MV12D FC/MC/PC48D 0.98 0.98 1.01 MV16C FC/MC/PC48C 0.99 0.99 1.00 MV20D FC/MC/PC48D 0.99 0.99 1.00

Furnaces Coils MBH KW COP

T*9X*B12 FC/MC/PC43B 1.00 1.06 0.95 T*(8,L)X*B12 FC/MC/PC43B 1.00 1.06 0.94 T*(8,L)X*C16 FC/MC/PC43C 0.98 1.07 0.91 T*9X*C16 FC/MC/PC43C 1.00 1.07 0.94 T*(8,L)X*C20 FC/MC/PC43C 0.99 1.08 0.92 T*9X*C20 FC/MC/PC43C 0.99 1.06 0.93

Furnaces Coils MBH KW COP

Y*(8,L)C*A12 FC/MC/PC37A 0.96 0.99 0.97 Y*(8,L)C*B12 FC/MC/PC43B 1.00 1.02 0.98

(Y*9C/T*9V)*B12 FC/MC/PC43B 1.00 1.02 0.98

Y*(8,L)C*C16 FC/MC/PC43C 0.99 1.05 0.94 Y*(8,L)C*C20 FC/MC/PC43C 0.98 1.05 0.94

(Y*9C/T*9V)*C16 FC/MC/PC43C 0.99 1.03 0.96 (Y*9C/T*9V)*C20 FC/MC/PC43C 0.99 1.04 0.95

Y*(8,L)C*C16 FC/MC/PC48C 0.99 1.06 0.93 Y*(8,L)C*C20 FC/MC/PC48C 0.98 1.06 0.93

(Y*9C/T*9V)*C16 FC/MC/PC48C 0.99 1.05 0.95 (Y*9C/T*9V)*C20 FC/MC/PC48C 1.01 1.05 0.96

Y*(8,L)C*C16 HC42 0.99 1.05 0.94 Y*(8,L)C*C20 HC42 0.98 1.05 0.93

(Y*9C/T*9V)*C16 HC42 0.99 1.03 0.97 (Y*9C/T*9V)*C20 HC42 0.99 1.04 0.95

Y*(8,L)C*B12 HD48 0.95 0.95 1.00 Y*(8,L)C*C16 HD48 0.95 0.97 0.98 Y*(8,L)C*C20 HD48 0.94 0.97 0.97

(Y*9C/T*9V)*B12 HD48 0.95 0.95 1.01 (Y*9C/T*9V)*C16 HD48 0.95 0.96 0.99 (Y*9C/T*9V)*C20 HD48 0.97 0.97 1.00

Y*(8,L)C*C16 UC48C 1.00 1.08 0.92 Y*(8,L)C*C20 UC48C 1.00 1.09 0.91

(Y*9C/T*9V)*C16 UC48C 1.00 1.08 0.93 (Y*9C/T*9V)*C20 UC48C 1.02 1.07 0.95

Johnson Controls Unitary Products 31

Page 32

397855-YTG-G-0509

HEATING PERFORMANCE DATA

CONDENSING UNIT MODEL NO YHJD42S41S1 EVAPORATOR COIL MODEL NO FC/MC/PC/UC48

AIR TEMP.

ENTERING

OUTDOOR UNIT

NOTE: ALL CAPACITIES ARE NET (KBTUH) WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM.

AIR TEMP.

ENTERING

INDOOR COIL

60 48.7 3.5 4.1 48.7 3.5 4.1 48.7 3.4 4.2 70 47.8 3.8 3.6 48.6 3.8 3.7 49.5 3.8 3.8 80 46.8 4.2 3.3 48.6 4.2 3.4 50.3 4.1 3.6 60 42.5 3.3 3.8 42.9 3.3 3.8 43.3 3.2 3.9 70 42.3 3.6 3.4 42.7 3.6 3.5 43.1 3.6 3.6 80 42.0 3.9 3.1 42.4 3.9 3.2 42.9 3.9 3.3 60 40.1 3.2 3.7 40.5 3.2 3.7 40.8 3.2 3.8 70 39.1 3.5 3.3 39.6 3.5 3.3 40.0 3.5 3.4 80 38.2 3.8 2.9 38.7 3.8 3.0 39.2 3.8 3.0 60 33.5 3.8 2.6 33.8 3.7 2.7 34.1 3.7 2.7 70 34.8 3.4 3.0 34.5 3.4 3.0 34.1 3.4 2.9 80 36.2 3.1 3.4 35.1 3.1 3.3 34.1 3.1 3.2 60 27.8 3.6 2.2 28.4 3.6 2.3 29.1 3.6 2.4 70 28.3 3.3 2.5 28.8 3.3 2.5 29.2 3.3 2.6 80 28.8 3.0 2.8 29.1 3.0 2.8 29.4 3.0 2.8 60 26.3 3.6 2.1 26.9 3.6 2.2 27.6 3.6 2.2 70 25.6 3.3 2.3 26.8 3.3 2.4 28.0 3.3 2.5 80 24.8 3.0 2.4 26.6 3.0 2.6 28.4 3.0 2.8

MBTUH KW C.O.P. MBTUH KW C.O.P. MBTUH KW C.O.P.

1200 1400 1600

ID CFM

Multipliers for determining the performance with other indoor sections.

Air Handlers Coils MBH KW COP

– FC/MC/PC60 1.00 1.06 0.94 – HC42 0.99 0.99 1.00 – HC60 1.00 1.06 0.94 – HD60 0.99 0.89 1.11 AHP/SHP48 – 1.00 1.00 1.00 AHX42 – 0.98 1.05 0.93 AHX48 – 0.98 1.07 0.92 AV/SV*48 – 0.98 1.05 0.94 F4FP045 – 1.01 1.07 0.94 F5FP048 – 0.99 1.01 0.98 F6FP042 – 0.99 1.06 0.94 F6FP048 – 0.99 1.09 0.91 MA14D FC/MC/PC48D 1.00 1.00 1.00 MA16C FC/MC/PC48C 1.00 1.00 1.00 MV16C FC/MC/PC48C 0.99 0.99 1.00 MV20D FC/MC/PC48D 0.98 0.98 1.00 MA14D FC/MC/PC60D 1.00 1.06 0.94 MA16C FC/MC/PC60C 1.00 1.06 0.94 MV20D FC/MC/PC60D 0.98 1.04 0.94

Continued on next page.

32 Johnson Controls Unitary Products

Page 33

Furnaces Coils MBH KW COP

T*(8,L)X*C16 FC/MC/PC48C 0.98 1.05 0.94 T*9X*C16 FC/MC/PC48C 0.99 1.04 0.95 T*(8,L)X*C20 FC/MC/PC48C 0.98 1.06 0.93 T*9X*C20 FC/MC/PC48C 0.98 1.05 0.94 T*9X*D20 FC/MC/PC48D 0.98 1.05 0.93 T*(8,L)X*C16 UC48C 0.98 1.09 0.90 T*9X*C16 UC48C 0.99 1.07 0.93 T*(8,L)X*C20 UC48C 0.99 1.10 0.90 T*9X*C20 UC48C 0.99 1.08 0.92 T*9X*D20 UC48D 0.99 1.09 0.91

Y*(8,L)C*C16 FC/MC/PC48C 0.99 1.04 0.95 Y*(8,L)C*C20 FC/MC/PC48C 0.99 1.05 0.95

(Y*9C/T*9V)*C16 FC/MC/PC48C 0.99 1.03 0.96 (Y*9C/T*9V)*C20 FC/MC/PC48C 0.99 1.03 0.97 (Y*9C/T*9V)*D20 FC/MC/PC48D 0.99 1.04 0.96 (Y*9C/T*9V)*D20 FC/MC/PC60D 1.00 1.08 0.93 (Y*9C/T*9V)*D20 FC/MC62D 0.99 1.06 0.94

Y*(8,L)C*C16 FC/PC60C 1.00 1.08 0.92 Y*(8,L)C*C20 FC/PC60C 0.99 1.09 0.91

(Y*9C/T*9V)*C16 FC/PC60C 1.00 1.05 0.95 (Y*9C/T*9V)*C20 FC/PC60C 1.00 1.07 0.94

Furnaces Coils MBH KW COP

Y*(8,L)C*C16 HC42 0.99 1.03 0.96 Y*(8,L)C*C20 HC42 0.99 1.03 0.96

(Y*9C/T*9V)*C16 HC42 0.99 1.02 0.98 (Y*9C/T*9V)*C20 HC42 0.99 1.02 0.97

Y*(8,L)C*B12 HD48 0.98 0.92 1.07 Y*(8,L)C*C16 HD48 0.98 0.95 1.03 Y*(8,L)C*C20 HD48 0.97 0.93 1.04

(Y*9C/T*9V)*B12 HD48 0.96 0.87 1.11 (Y*9C/T*9V)*C16 HD48 0.98 0.92 1.06 (Y*9C/T*9V)*C20 HD48 0.98 0.94 1.04 (Y*9C/T*9V)*D20 HD48 0.98 0.95 1.03

Y*(8,L)C*C16 UC48C 0.99 1.07 0.93 Y*(8,L)C*C20 UC48C 0.99 1.07 0.93

(Y*9C/T*9V)*C16 UC48C 1.00 1.06 0.94 (Y*9C/T*9V)*C20 UC48C 1.00 1.05 0.95 (Y*9C/T*9V)*D20 UC48D 1.00 1.06 0.94

Y*(8,L)C*C16 UC60C 0.99 1.07 0.93 Y*(8,L)C*C20 UC60C 0.99 1.08 0.92

(Y*9C/T*9V)*C16 UC60C 1.00 1.04 0.96 (Y*9C/T*9V)*C20 UC60C 1.00 1.05 0.95 (Y*9C/T*9V)*D20 UC60D 1.00 1.06 0.94

Johnson Controls Unitary Products 33

Page 34

397855-YTG-G-0509

HEATING PERFORMANCE DATA

CONDENSING UNIT MODEL NO YHJD48S41S1 EVAPORATOR COIL MODEL NO AHP/SHP48

AIR TEMP.

ENTERING

OUTDOOR UNIT

NOTE: ALL CAPACITIES ARE NET (KBTUH) WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM.

AIR TEMP.

ENTERING

INDOOR COIL

60 60.1 4.0 4.4 61.4 4.0 4.5 62.7 3.9 4.7 70 59.0 4.1 4.3 59.2 4.3 4.0 61.1 4.3 4.2 80 57.9 4.1 4.1 57.0 4.7 3.6 59.5 4.7 3.7 60 52.1 3.3 4.7 51.4 3.7 4.0 48.1 3.7 3.8 70 51.3 3.6 4.2 50.7 4.2 3.6 49.4 4.1 3.5 80 50.4 3.9 3.8 50.0 4.6 3.2 50.8 4.6 3.2 60 47.4 3.2 4.4 45.5 3.7 3.6 48.5 3.7 3.8 70 46.9 3.5 3.9 45.5 4.1 3.2 47.1 4.1 3.4 80 46.5 3.9 3.5 45.5 4.5 3.0 45.7 4.5 3.0 60 41.8 3.0 4.0 38.4 4.3 2.6 37.3 4.2 2.6 70 41.5 3.4 3.6 37.5 3.9 2.9 37.9 3.9 2.9 80 41.3 3.7 3.3 36.6 3.4 3.1 38.4 3.5 3.2 60 35.1 2.9 3.6 28.6 3.9 2.2 29.5 4.0 2.2 70 35.0 3.2 3.2 29.1 3.6 2.4 29.9 3.6 2.4 80 34.9 3.5 2.9 29.5 3.3 2.6 30.2 3.3 2.7 60 32.0 2.8 3.4 25.8 3.9 2.0 26.4 3.9 2.0 70 31.8 3.1 3.0 26.4 3.6 2.2 27.3 3.6 2.2 80 31.7 3.4 2.8 27.0 3.3 2.4 28.1 3.4 2.5

MBTUH KW C.O.P. MBTUH KW C.O.P. MBTUH KW C.O.P.

1400 1600 1800

ID CFM

Multipliers for determining the performance with other indoor sections.

Air Handlers Coils MBH KW COP

– FC/MC/PC48 1.00 0.95 1.04 – FC/MC/PC60 1.00 1.02 0.99 – HC60 1.00 1.02 0.99 – HD60 0.98 0.85 1.16 – MC62 1.00 0.97 1.03 AHP60 – 0.99 1.01 0.99 AHX48 – 0.98 1.01 0.97 AV*48 – 0.99 1.01 0.99 AV/SV*60 – 0.98 0.99 0.98 F4FV060 – 0.99 1.01 0.99 F5FP048 – 0.99 0.98 1.02 F5FP060 – 1.00 1.02 0.98 F6FP048 – 0.99 1.04 0.95 MA16C FC/MC/PC48C 1.00 0.95 1.04 MA20D FC/MC/PC48D 1.00 0.95 1.04 MV16C FC/MC/PC48C 0.99 0.94 1.04 MV20D FC/MC/PC48D 0.99 0.94 1.04 MA16C FC/MC/PC60C 1.00 1.02 0.99 MA20D FC/MC/PC60D 1.00 1.02 0.99 MV20D FC/MC/PC60D 0.99 1.01 0.99 MA20D MC62D 1.00 0.97 1.03 MV20D MC62D 0.99 0.96 1.03

Furnaces Coils MBH KW COP

T*(8,L)X*C16 FC/PC60C 0.98 0.99 0.99 T*9X*C16 FC/PC60C 0.98 0.99 1.00

Furnaces Coils MBH KW COP

T*(8,L)X*C20 FC/MC/PC60D 0.98 0.99 0.99 T*9X*C20 FC/PC60C 0.98 0.99 0.99 T*9X*D20 FC/MC/PC60D 0.97 1.00 0.97 T*9X*D20 FC/MC62D 0.99 1.01 0.98 T*(8,L)X*C16 UC60C 0.99 1.02 0.97 T*(8,L)X*C20 UC60D 0.97 1.04 0.94 T*9X*C16 UC60C 0.99 1.02 0.97 T*9X*C20 UC60C 0.99 1.03 0.96 T*9X*D20 UC60D 0.97 1.03 0.95 (Y*9C/T*9V)*D20 FC/MC/PC60D 0.99 1.00 1.00 (Y*9C/T*9V)*D20 FC/MC62D 1.00 1.01 0.98

Y*(8,L)C*C16 FC/PC60C 0.99 1.00 0.99 Y*(8,L)C*C20 FC/PC60C 0.99 1.02 0.97

(Y*9C/T*9V)*C16 FC/PC60C 1.00 0.99 1.00 (Y*9C/T*9V)*C20 FC/PC60C 1.00 0.99 1.00 (Y*9C/T*9V)*D20 HC60 1.00 1.03 0.97

Y*(8,L)C*C16 HD60 0.98 0.94 1.04 Y*(8,L)C*C20 HD60 0.98 0.96 1.03

(Y*9C/T*9V)*C16 HD60 0.99 0.94 1.05 (Y*9C/T*9V)*C20 HD60 0.99 0.94 1.05 (Y*9C/T*9V)*D20 HD60 0.98 0.94 1.05

Y*(8,L)C*C16 UC60C 0.99 1.02 0.98 Y*(8,L)C*C20 UC60C 0.99 1.03 0.96

(Y*9C/T*9V)*C16 UC60C 1.00 1.01 0.99 (Y*9C/T*9V)*C20 UC60C 1.00 1.01 0.99

34 Johnson Controls Unitary Products

Page 35

Furnaces Coils MBH KW COP

(Y*9C/T*9V)*D20 UC60D 1.00 1.01 0.98

Johnson Controls Unitary Products 35

Page 36

HEATING PERFORMANCE DATA

CONDENSING UNIT MODEL NO YHJD60S41S1 EVAPORATOR COIL MODEL NO FC/MC62

AIR TEMP.

ENTERING

OUTDOOR UNIT

NOTE: ALL CAPACITIES ARE NET (KBTUH) WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM.

AIR TEMP.

ENTERING

INDOOR COIL

60 65.7 4.7 4.1 66.7 4.6 4.2 67.6 4.6 4.3 70 64.7 5.1 3.7 65.4 5.0 3.8 66.1 4.9 3.9 80 63.8 5.5 3.4 64.1 5.4 3.5 64.5 5.3 3.6 60 56.9 4.4 3.8 57.4 4.4 3.9 58.0 4.3 4.0 70 55.8 4.8 3.4 56.3 4.8 3.5 56.8 4.7 3.5 80 54.7 5.2 3.1 55.2 5.2 3.1 55.6 5.1 3.2 60 51.9 4.3 3.5 51.7 4.3 3.5 51.4 4.3 3.5 70 50.6 4.8 3.1 51.1 4.7 3.2 51.7 4.7 3.2 80 49.3 5.2 2.8 50.6 5.1 2.9 51.9 5.0 3.0 60 44.1 5.0 2.6 43.6 5.0 2.5 43.1 5.0 2.5 70 45.3 4.6 2.9 44.8 4.6 2.9 44.4 4.6 2.8 80 46.5 4.2 3.2 46.1 4.2 3.2 45.6 4.1 3.2 60 36.6 5.0 2.2 36.8 4.9 2.2 36.9 4.9 2.2 70 36.0 4.5 2.4 36.5 4.5 2.4 37.1 4.4 2.4 80 35.3 4.0 2.6 36.3 4.0 2.6 37.3 4.0 2.7 60 27.3 4.7 1.7 27.7 4.6 1.7 28.1 4.6 1.8 70 30.4 4.4 2.0 31.2 4.3 2.1 32.0 4.3 2.2 80 33.4 4.0 2.4 34.7 4.0 2.5 35.9 4.0 2.7

MBTUH KW C.O.P. MBTUH KW C.O.P. MBTUH KW C.O.P.

1600 1800 2000

ID CFM

Multipliers for determining the performance with other indoor sections.

Air Handlers Coils MBH KW COP

AHX60 – 1.00 1.02 0.99 F6FP060 – 0.99 1.01 0.98 MA20D MC62D 1.00 1.00 1.00 MV20D MC62D 0.99 0.99 1.00

Furnaces Coils MBH KW COP

T*(8,L)X*C20 FC/MC62D 0.98 1.02 0.96 T*9X*D20 FC/MC62D 0.98 0.97 1.01 (Y*9C/T*9V)*D20 FC/MC/PC60D 0.98 0.97 1.02

Y*(8,L)C*C20 FC/MC62D 0.98 1.01 0.98

(Y*9C/T*9V)*C20 FC/MC62D 0.99 0.99 1.01

Subject to change without notice. Published in U.S.A. 397855-YTG-G-0509

Johnson Controls Unitary Products

5005 York Drive

Norman, OK 73069

York YHJD18 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual