York XP Sunline R410A 13 SEER, ZF Sunline R410A 13 SEER, ZR Sunline MagnaDry R410A 13 SEER Technical Guide

TECHNICAL GUIDE

R-410A
ZE/ZF/ZR/XN/XP SERIES
3 - 6 TON

251933-YTG-X-0615

Description

YORK® ZE/ZF/ZR/XN/XP Series units are convertibl e si ng l e
package high efficiency rooftops with a common roof curb for
the 3, 4, 5 and 6 Ton sizes (ZE, ZR, XN, XP not available in 6
Ton). Although the units are primarily designed for curb
mounting on a roof, they can also be slab-mounted at ground
level or set on steel beams above a finished roof.

All ZE/ZF/ZR/XN/XP Series units are self-contained and
assembled on rigid full perimeter base rails allowing for
overhead rigging. Every unit is completely charged, wired,
piped and tested at the factory to provide a quick and easy field
installation.

All models (including those with an economizer) are convertible
between bottom and horizontal duct connections.

60 Hertz

ZE/ZF/ZR Series units are available in the following
configurations: cooling only, cooling with electric heat, and
cooling with one or two stage gas heat. Electric heaters are
available as factory-installed option or field installed accessory.

XN/XP Series units are available in the following configurations:
cooling and heating only and cooling and heating with electric
heat.

Tested in accordance with:

FOR DISTRIBUTION USE ONLY - NOT TO BE USED AT POINT OF RETAIL SALE

251933-YTG-X-0615

Smoke
Detector

3/4” PVC Female
Condensate Drain

GFCI

Convenience Outlet

Knockout
For Side
Control Entry

Simplicity® Lite™

Or Simplicity SE

Control Board

Knockout For Side
Gas Supply Entry

Full Perimeter Baserails

With Forklift Slots And

Lifting Holes

Highly Efficient
Enhanced Copper
Tube/Enhanced
Aluminum Fin
Or
Micro-Channel
Aluminum
Tube/Aluminum
Fin Condenser

High Efficiency
Compressor

Power Ventor Motor With

Post Purge Cycle

20 Gauge Aluminized

Steel Tubular Heat Exchanger

Belt Drive Or

Direct Drive

Blower

HACR
Breaker

Economizer

Hood

Knockout
For Side
Power Entry

Slide-In
Economizer

Table of Contents

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Component Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Features and Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Guide Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Physical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Capacity Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Airflow Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Sound Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

Electrical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

Typical Field Power and Control Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143

Weights and Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147

Component Location

Gas/Electric

2 Johnson Controls Unitary Products

Electric/Electric and Heat Pump

Economizer

Hood

Electric Heat

Accessory Location

High Efficiency
Compressor

Highly Efficient
Enhanced Copper
Tube/Enhanced
Aluminum Fin
Or
Micro-Channel
Aluminum
Tube/Aluminum
Fin Condenser

Full Perimeter Baserails

With Forklift Slots And

Lifting Holes

Simplicity® Lite™

Or
Simplicity® SE
Control Board

Belt Drive Or

Direct Drive

Blower

Knockout
For Side
Control Entry

GFCI

Convenience Outlet

3/4” PVC Female
Condensate Drain

Smoke
Detector

Slide-In
Economizer

Knockout
For Side
Power Entry

HACR
Breaker

251933-YTG-X-0615

Johnson Controls Unitary Products 3

251933-YTG-X-0615

Z E 048 N04 A 2 A AA 4 0 1 2 4 A

Z = A/C, Single Pkg., R-410A
X = HP, Single Pkg., R-410A

Product Category

Airow

A = Direct Drive
B = Direct Drive/Single Input Low Leak Econo
D = Direct Drive/Motorized Damper
N = Belt Drive
P = Belt Drive/Single Input Low Leak Econo
R = Belt Drive/Motorized Damper
T = Belt Drive High Static
U = Belt Drive High Static/Single Input Low Leak Economizer
V = Belt Drive High Static/Motorized Damper

Product Generation

4 = Fourth Generation

*(D, T)10 = 92 MBH Output on 036 Models

036 = 3.0 Ton

Nominal Cooling Capacity

048 = 4.0 Ton
060 = 5.0 Ton
072 = 6.0 Ton

Product Identifier

= 11.2 EER2, A/C
= 11.0 EER

3

, CLG/GAS
R = 13.0 SEER Reheat
P = 13.0 SEER HP

Product Style

A = Style A

SS Drain Pan

Configuration Options (not required for all units)

These four digits will not be assigned until a quote is requested, or an order placed.

CPC Controller, DFS, APS

Honeywell Controller, DFS, APS

Novar Controller, DFS, APS

2" Pleated Filters, MERV 7

BAS Ready Economizer (2-10 V.D.C. Actuator Without a Controller)

Any Combination of Additional Options that Don’t Have an Option Code Pre-assigned

1. 3 thru 5 Ton Units

2. 6 Ton Units Cooling Only / Cooling With Electric Heat

3. 6 Ton Unit Cooling With Gas Heat

F = 13.0 SEER

1

, A/C

E = 14.0 SEER, A/C

N = 14.0 SEER HP

Simplicity® Smart Equipment (SSE) w/Communication
BACnet MS/TP (programmable to Modbus or N2 protocols)

Johnson Controller UNT 1126 (N2 protocol), DFS, APS

C00 = Cooling Only. Suitable for Field

Installed Electric Heat

Heat Type and Nominal Heat Capacity

N04 = 40 MBH Output Aluminized Steel, 1 Stage (036)
N06 = 60 MBH Output Aluminized Steel, 1 Stage (048)
N08 = 80 MBH Output Aluminized Steel, 1 Stage

(036, 060, 072)

N10 = 100 MBH Output Aluminized Steel, 1 Stage

(048, 060, 072)

D06 = 60 MBH Output Aluminized Steel, 2 Stage

(036, 048, 060, 072)

D10 = 100 MBH Output Aluminized Steel, 2 Stage

(036*, 048, 060, 072)
S04 = 40 MBH Output Stainless Steel, 1 Stage (036)
S06 = 60 MBH Output Stainless Steel, 1 Stage (048)
S08 = 80 MBH Output Stainless Steel, 1 Stage

(036, 060, 072)
S10 = 100 MBH Output Stainless Steel, 1 Stage

(048, 060, 072)
T06 = 60 MBH Output Stainless Steel, 2 Stage

(036, 048, 060, 072)
T10 = 100 MBH Output Stainless Steel, 2 Stage

(036*, 048, 060, 072)

E05 = 5 KW
E07 = 7 KW
E10 = 10 KW
E15 = 15 KW
E20 = 20 KW
E30 = 30 KW

Gas Heat Options

Electric Heat Options

Voltage

1 = 208/230-1-60
2 = 208/230-3-60

4 = 460-3-60
5 = 575-3-60

York Commercial Comfort System (YCCS) Rtu Controller

3 = 380-3-60

A = No Options Installed

Installation Options

B = Option 1
C = Option 2
D = Options 1 & 2
E = Option 3
F = Option 4
G = Options 1 & 3
H = Options 1 & 4
J = Options 1, 2 & 3
K = Options 1, 2, & 4
L = Options 1,3 & 4
M = Options 1, 2, 3, & 4

N = Options 2 & 3
P = Options 2 & 4
Q = Options 2, 3, & 4
R = Options 3 & 4
S = Option 5
T = Options 1 & 5
U = Options 1, 3, & 5
V = Options 1, 4, & 5
W = Options 1, 3, 4, & 5
X = Options 3 &

5
Y = Options 4 & 5
Z = Options 3, 4 & 5

1 = Disconnect
2 = Non-Pwr'd Conv. Outlet
3 = Smoke Detector S.A.
4 = Smoke Detector R.A.
5 = Pwr'd Conv. Outlet

Options

AA = None
AB = Phase Monitor
AC = Coil Guard
AD = Dirty Filter Switch
AE = Phase Monitor & Coil Guard
AF = Phase Monitor & Dirty Filter Switch
AG = Coil Guard & Dirty Filter Switch
AH = Phase Monitor, Coil Guard & Dirty Filter Switch
AS = Bottom Drain Connection
RC = Coil Guard & American Flag
TA = Technicoat Condenser Coil
TJ = Technicoat Evaporator Coil
TS = Technicoat Evaporator and Condenser Coil
EA = E-Coat Condenser Coil
EJ = E-Coat Evaporator Coil
ES = E-Coat Cond & Evap Coils
1A = Simplicity SE
1B = Phase Monitor & Simplicity SE
1C = Coil Guard & Simplicity SE
1D = Dirty Filter Switch & Simplicity SE
1E = Phase Monitor, Coil Guard, Simplicity SE
1F = Phase Monitor, Dirty Filter Switch, Simplicity SE
1G = Coil Guard & Dirty Filter Switch, Simplicity SE
1H = Phase Monitor, Coil Guard, Dirty Filter Switch,
Simplicity SE

Standard Cabinet

Additional Options

ZZ = If desired option combination is not listed above, ZZ will be assigned and conguration options will be

located in digits 15-18.

Hinged & Toolless Access Cabinet

BA = Hinged & Toolless Filter, Motor and Electrical
Access Panels
BB = Phase Monitor, Hinged & Toolless Filter, Motor
and Electrical Access Panels
BC = Coil Guard, Hinged & Toolless Filter, Motor and
Electrical Access Panels
BD = Dirty Filter Switch, Hinged & Toolless Filter,
Motor and Electrical Access Panels
BE = Phase Monitor & Coil Guard, Hinged & Toolless
Filter, Motor and Electrical Access Panels
BF = Phase Monitor & Dirty Filter Switch, Hinged &

Toolless Filter, Motor and Electrical Access

Panels
BG = Coil Guard & Dirty Filter Switch, Hinged &

Toolless Filter, Motor and Electrical Access

Panels

BH = Phase Monitor, Coil Guard & Dirty Filter Switch,
Hinged & Toolless Filter, Motor and Electrical
Access Panels
2A = Hinged & Toolless Access Panels, Simplicity SE
2B = Hinged & Toolless Access Panels, Phase
Monitor, Simplicity SE
2C = Hinged & Toolless Access Panels, Coil Guard &
Simplicity SE
2D = Hinged & Toolless Access Panels, Dirty Filter
Switch, Simplicity SE
2E = Hinged & Toolless Access Panels, Phase
Monitor, Coil Guard, Simplicity SE
2F = Hinged & Toolless Access Panels, Phase
Monitor, Dirty Filter Switch, Simplicity SE
2G = Hinged & Toolless Access Panels, Coil Guard,
Dirty Filter Switch, Simplicity SE
2H = Hinged & Toolless Access Panels, Phase
Monitor, Coil Guard, Dirty Filter Switch,
Simplicity SE

Nomenclature

4 Johnson Controls Unitary Products

251933-YTG-X-0615

Features and Benefits

Standard Features

• High Efficiency - High efficiency 3 thru 5 Ton units reach

14.0/13.0 SEER, 6 Ton Cooling only or Cooling with
Electric Heat reach 11.2 EER and 6 Ton Cooling with Gas
Heat reach 11.0 EER. Gas/electric units have electronic
spark ignition and power vented combustion with steady
state efficiencies of 80%. High efficiency heat pumps
reach 14/13 SEER and 8.0/7.7 H.S.P. F. These
efficiencies exceed all legislated minimum levels and
provide low operating costs.

• Coil Technology – All ZE/ZF condensers utilize Micro­Channel “all-aluminum” condensers which provide
improved heat transfer capabilities and reduced charge
volumes. All evaporators utilize a conventional copper
tube/aluminum fin design for proven reliability and
performance.

• Convertible Airflow Design - All models (including those
with an economizer) are suitable for either bottom or
horizontal duct connections. For bottom duct, remove the
sheet metal panels from the supply and return air openings
through the base of the unit. For horizontal duct, remove
the supply and return air panels on the rear of the unit.

• System Protection - Suction line freezestats are supplied
on all units to protect against loss of charge and coil
frosting when the economizer operates at low outdoor air
temperatures while the compressors are running. Every
unit has solid-core liquid line filter-driers and high and low­pressure switches. Internal compressor protection is
standard on all compressors.

• Advanced Controls - ZE/ZF (Electric/Electric and Gas/
Electric) with no factory installed economizer or BAS
options will come standard with the reliable Simplicity
Lite™ control. All ZE/ZF models with factory installed
economizers or any BAS option, reheat (ZR) and heat
pump (XP, XN) Units will come with the new state of the
art Simplicity SE (Smart Equipment) control system. The
new unit control incorporates the best of the already
proven Simplicity
robust, intelligent control. The goal of this control is to
utilize cutting edge technology making the equipment
easier to install, operate, and service. All units are Factory
commissioned, configured, and run tested.

®

unitary controls and creates a more

Simplicity SE Control Board

• Versatile - The Simplicity SE (not applicable with units
utilizing Simplicity Lite) control can be configured to use
with a standard thermostat (easy to connect screw
terminals), A zone sensor, or can be setup to
communicate with multiple BAS communication
protocols to integrate with building automation systems.

• Reduce field installed complexity - Each unit (not
applicable with units utilizing Simplicity Lite) will comes
equipped with factory installed supply air, return air, and
outdoor air temperature sensors providing key
temperature readings thus reduce field installed
complexity.

®

• On-board USB Port - The new control (not applicable
with units utilizing Simplicity Lite) comes with a long list
of features including data logging, current and previous
system faults and software update capabilities using the
on board USB port and common flash drive. Energy use
monitoring capabilities allow custom tailoring to allow a
system to work more efficiently at all times and
occupancy levels. Self test and start-up reports also
available from the board VIA the USB port.

• Embedded LCD Display - The board (not applicable
with units utilizing Simplicity Lite) has a easy to read,
built-in LCD display and easy to use navigation joystick
and buttons allowing the user to quickly navigate the
menus displaying unit status, options, current function,
supply, return and outdoor temperatures, fault codes
and other information.

• Low Ambient - An integrated low-ambient control
allows all units to operate in the cooling mode down to
0F outdoor ambient without additional assistance.
Optionally, the control board can be programmed to
lockout the compressors when the outdoor air
temperature is low or when free cooling is available.

Johnson Controls Unitary Products 5

251933-YTG-X-0615

The

Simplicity

this product will effectively operate the cooling sys­tem down to 0°F when this product is applied in a
comfort cooling application for people. An econo­mizer is typically included in this type of applica­tion. When applying this product for process
cooling applications (computer rooms, switchgear,
etc.), please reference applications bulletin AE­011-07 or call the applications department for Uni­tary Products @ 1-877-UPG-SERV for guidance.
Additional accessories may be needed for stable
operation at temperatures below 30° F.

• Anti-Short Cycle Protection - To aid compressor life,
an anti-short cycle delay is incorporated into the
standard controls. Compressor reliability is further
ensured by programmable minimum run times. For
testing, the anti-short cycle delay can be temporarily
overridden with the push of a button.

• Fan Delays - Fan on and fan off delays are fully
programmable. Furthermore, the heating and cooling
fan delay times are independent of one another. All units
are programmed with default values based upon their
configuration of cooling and heat.

• Safety Monitoring - The control board monitors the
high and low-pressure switches, the freezestats, the gas
valve, if applicable, and the temperature limit switch on
gas and electric heat units. The unit control board will
alarm on ignition failures, compressor lockouts and
repeated limit switch trips.

• Nuisance Trip Protection and Strikes - To prevent
nuisance trouble calls, the control board uses a “three
times, you’re out” philosophy. The high and low­pressure switches and the freezestats must trip three
times within two hours before the unit control board will
lock out the associated compressor.

• On Board Diagnostics - Each alarm will energize a
trouble light on the thermostat, if so equipped, and flash
an alarm code on the control board LED or on LCD with
Simplicity SE controlled units. Each high and low­pressure switch alarm as well as each freezestat alarm
has its own flash code. The control board saves the five
most recent alarms in memory, and these alarms can be
reviewed at any time. Alarms and programmed values
are retained through the loss of power.

• Reliable - From the beginning - All units undergo
computer automated testing before they leave the factory.
Units are tested for refrigerant charge and pressure, unit
amperage, and 100% functionality. For the long term - All
units are painted with a long lasting, powder paint that
stands up over the life of the unit. The paint used has
been proven by a 1000 hour salt spray test.

• Flexible Placement - All models and configurations share
the same cabinet/footprint and thus the same roof curb.
You have the flexibility to set one curb and choose the

® Lite or SE control board used in

correct tonnage size and heating option after the internal
loads have been determined.

• Full Perimeter Base Rails - The permanently attached
base rails provide a solid foundation for the entire unit and
protect the unit during shipment. The rails offer forklift
access from 3 sides, and rigging holes are available so that
an overhead crane can be used to place the units on a roof.

• Easy Installation - Gas and electric utility knockouts are
supplied in the unit underside as well as the side of the
unit. A clearly identified location is provided to mount a
field supplied electrical disconnect switch. Utility
connections can be made quickly and with a minimum
amount of field labor.

• Wide Range of Indoor Airflows - Indoor fan motors are
either direct-drive or belt-drive type providing maximum
flexibility to handle most airflow requirements.

• Gas Heat Operation - All single phase models with gas
heat have minimum annual fuel utilization efficiency
(AFUE) of 81%. All three phase models with gas heat
have minimum steady state efficiency of 80%. Each
section includes a durable heat exchanger with
aluminized steel or optional stainless steel tubes, a
redundant gas valve, spark ignition, power venting, an
ignition module for 100% shut-off and all of the safety
controls required to meet the latest ANSI standards.

The gas supply piping can be routed into the heating
compartment through a hole in the base pan of the unit or
through a knockout in the piping panel on the front of the
unit.

Electric Heat Operation - All electric heat models are
wired for a single power source and include a bank of
nickel chromium elements mounted at the discharge of
the supply air blower to provide a high velocity and
uniform distribution of air across the heating elements.

Every element is fully protected against excessive
temperature by thermal limit switches.

The power supply wiring can be routed into the control
box through a threaded pipe connection (field supplied) in
the base pan of the unit or through a knockout in the
wiring panel on the side of the unit.

• Warranty - All models include a 1-year limited warranty
on the complete unit. Compressors and electric heater
elements each carry a 5-year warranty. Aluminized steel
and stainless steel tubular heat exchangers carry a 10­year warranty.

Factory Installed Options

NOTE: Simplicity Lite models are only available with a field

installed Honeywell Jade economizer which is
equipped standard with single enthalpy control (dual
enthalpy available as field installed kit). Simplicity SE
models are available with factory or field installed
economizers including options for a SSE controlled
economizer or an externally controlled BAS economizer
where both feature standard dry bulb control (single
and dual enthalpy available as field installed kits).

• Economizers - All units offer a variety of optional factory
installed economizers that are shipped, installed and
wired with AMCA 511 Licensed Class 1A low leak

6 Johnson Controls Unitary Products

251933-YTG-X-0615

dampers designed to exceed ASHRAE 90.1-2010 and the
International Energy Conservation Code (IECC)
certification requirements by achieving leakage rates of 3
cfm/ sq. ft. at 1" of static pressure. Each economizer goes
through a rigorous 60,000 cycle test. Dry bulb, single
enthalpy, and dual enthalpy (with field installed kit) can be
selected. All economizer options are fully integrated into
the Simplicity SE controls. The economizer has spring
return, fully modulating damper actuators and is capable
of introducing up to 100% outdoor air. As the outdoor air
intake dampers open, the return air dampers close. The
changeover from mechanical refrigeration to economizer
operation is regulated by the outdoor air dry bulb
temperature or the outdoor air enthalpy input. The dual
enthalpy kit provides a second input used to monitor the
return air (field installed). The installer needs only to
assemble the outdoor air hood, attach the enthalpy control
the hood and mount the hood to the unit (Hood and
control are provided).

• Dry Bulb Economizer - Economizer operation is
enabled by the outdoor air temperature being less than
the setpoint of the economizer module.

• Enthalpy Economizer - The added outdoor air enthalpy
sensor enables economizer operation if the outdoor
enthalpy is less than the setpoint of the economizer
logic module.

• Motorized Outdoor Air Intake Damper -Includes a slide­in / plug-in damper assembly with a 2-position, spring
return motor actuator which opens to a pre-set position
whenever the supply air blower is operating and will drive
fully closed when the blower unit shuts down.

The rain hood is painted to match the basic unit and must
be field assembled before installing.

• Technicoat Condenser Coils - The condenser coils are
coated with a phenolic coating for protection against
corrosion due to harsh environments.

• Technicoat Evaporator Coil - The evaporator coils are
coated with a phenolic coating for protection against
corrosion due to harsh environments.

• E-coat Condenser Coils - The condenser coils are
coated with an epoxy polymer coating to protect against
corrosion.

• E-coat Evaporator Coils - The evaporator coils are
coated with an epoxy polymer coating to protect against
corrosion.

• Electric Heaters - Wired for single point power supply.
These nickel chromium heater elements are provided with
limit and automatic reset capability to prevent operation at
excessive temperatures.

• Filter Options - Standard units are shipped with 1" throw­away filters installed. 2" Pleated Filters, MERV 7 are
offered as a factory installed option.

• Convenience Outlet - This 110 volt outlet can be
“powered” by the unit with a stepdown transformer or the
unit may be ordered with a “non-powered” convenience
outlet that can be wired in the field.

• Disconnect Switch - For gas heat units and cooling units
with electric heat, a HACR breaker sized to th e unit is

provided. For cooling only units, a switch sized to the
largest electric heat available for the particular unit is
provided. Factory installed option only.

• Smoke Detectors - (supply air & return air) The smoke
detectors stop operation of the unit by interrupting power
to the control board if smoke is detected within the air
compartment.

Factory installed smoke detectors in the return air, may
be subjected to freezing temperatures during “off” times
due to out side air infiltration. These smoke detectors
have an operational limit of 32°F to 131°F. Smoke
detectors installed in areas that could be out side those
limitations will have to be moved to prevent having false
alarms.

• Coil Guard - Customers can purchase a coil guard kit to
protect the condenser coil from damage. This is not a hail
guard kit.

• Stainless Steel Heat Exchanger - For applications in
corrosive environments, this option provides a full
stainless steel heat exchanger assembly.

• Stainless Steel Drain Pan - An optional rustproof
stainless steel drain pan is available to provide years of
trouble-free operation in corrosive environments.

Bottom Drain Connection - An optional bottom drain

•
connection is available for inside the curb connections for
applications in cold environments to reduce freezing drain
lines.

• Phase Monitors - Designed to prevent unit damage. The
phase monitor will shut the unit down in an out-of phase
condition.

• Dirty Filter Switch - This kit includes a differential
pressure switch that energizes the fault light on the unit
thermostat, indicating that there is an abnormally high
pressure drop across the filters. Factory installed option or
field installed accessory.

• Hinged & Toolless Filter, Motor and Electrical Access
Panels - This option allows for easy access and
maintenance.

NOTE: Knobs are shipped inside the unit to prevent shipping

damage. These must be field installed for tool-less
operation.

• High Static Drive - May include a belt, blower pulley,
motor pulley or a motor change to enhance blower
performance.

Control Options

• Simplicity® SE with Communication Option Control ­The York® Simplicity® SE with Communication Option
Control is factory installed. It includes all the features of
the Simplicity® SE control with an additional gateway to
BACnet MS/TP (programmable to Modbus or N2
protocols).

Johnson Controls Unitary Products 7

251933-YTG-X-0615

• Novar® BAS Control - The Novar® building automation
system controller is factory installed. Incudes supply air
sensor, return air sensor, dirty filter indicator switch, and
air proving switch.

• CPC BAS Control - The Computer Process Controls
Model 810-3060 ARTC Advanced Rooftop building
automation system controller is factory installed. Includes
supply air sensor, return air sensor, dirty filter indicator
switch and air proving switch.

• Honeywell BAS Control - The Honeywell W7750C
building automation system controller is factory installed.
Includes air supply sensor, return air sensor, dirty filter
indicator switch, and air proving switch.

• York Commercial Comfort System (YCCS) - Provides
rooftop system integration for YCCS single zone and
change-over bypass systems.

Field Installed Accessories

NOTE: Simplicity Lite models are only available with a field

installed Honeywell Jade economizer which is
equipped standard with single enthalpy control (dual
enthalpy available as field installed kit). Simplicity SE
models are available with factory or field installed
economizers including options for a SSE controlled
economizer or an externally controlled BAS economizer
where both feature standard dry bulb control (single
and dual enthalpy available as field installed kits).

• Economizers - All units offer a variety of optional field
installed economizers that are shipped, installed and
wired with AMCA 511 Licensed Class 1A low leak
dampers designed to exceed ASHRAE 90.1-2010 and the
International Energy Conservation Code (IECC)
certification requirements by achieving leakage rates of 3
cfm/ sq. ft. at 1" of static pressure. Each economizer goes
through a rigorous 60,000 cycle test. Dry bulb, single
enthalpy, and dual enthalpy (with field installed kit) can be
selected. All economizer options are fully integrated into
the Simplicity SE controls. The economizer has spring
return, fully modulating damper actuators and is capable
of introducing up to 100% outdoor air. As the outdoor air
intake dampers open, the return air dampers close. The
changeover from mechanical refrigeration to economizer
operation is regulated by the outdoor air dry bulb
temperature or the outdoor air enthalpy input. The dual
enthalpy kit provides a second input used to monitor the
return air (field installed). The installer needs only to
assemble the outdoor air hood, attach the enthalpy control
the hood and mount the hood to the unit (Hood and
control are provided).

• Dry Bulb Economizer - Economizer operation is

enabled by the outdoor air temperature being less than
the setpoint of the economizer module.

• Enthalpy Economizer - The added outdoor air enthalpy

sensor enables economizer operation if the outdoor
enthalpy is less than the setpoint of the economizer
logic module.

• Motorized Outdoor Air Intake Damper -Includes a slide­in / plug-in damper assembly with a 2-position, spring

return motor actuator which opens to some pre-set
position whenever the supply air blower is operating and
will drive fully closed when the blower unit shuts down.

The rain hood is painted to match the basic unit and must
be field assembled before installing.

• Electric Heaters - wired for single point power supply.
These nickel chromium heater elements are provided with

limit and automatic reset capability to prevent operation at
excessive temperatures.

• Roof Curbs - Eight and fourteen-inch high roof curbs
provide a water-tight seal between the unit and the finished
roof. These full perimeter curbs meet the requirements of
the National Roofing Contractors Association (NRCA) and
are shipped knocked-down for field assembly.

Roof curbs are designed to fit inside the base rails of the
unit and include both a wood nailing strip and duct hanger
supports.

• High Altitude Natural Gas - Burner orifices and pilot
orifices are provided for proper furnace operation at
altitudes up to 6,000 feet.

• Propane - Burner orifices, pilot orifices and gas valve
parts are provided to convert a natural gas furnace to
propane.

• High Altitude Propane - Burner orifices and pilot orifices
are provided for proper furnace operation at altitudes up
to 6,000 feet. This accessory supplements the basi c
propane conversion kit.

• Low Nox Kit - Required to reduce the emission of
nitrogen oxides below 40 nano grams per joule.

• Power Exhaust

- Our single input economizer options are
available with power exhaust. Whenever the outdoor air
intake dampers are opened for free cooling, the exhaust
fan will be energized to prevent the conditioned space from
being over-pressurized during economizer operation.

The power exhaust option can only be used on bottom
duct configurations.

• Barometric Relief Damper - This damper accessory can
be used to relieve internal building air pressure on units
with an economizer without power exhaust. This
accessory includes a rain hood, a bird screen and a fully
assembled damper. With bottom duct connections, the
damper should be mounted over the opening in the return
air panel. With horizontal ductwork, the accessory should
be mounted on the return air duct.

• Enthalpy Accessory Control Kit - This kit contains the
required components to convert a single enthalpy
economizer to dual enthalpy.

• Burglar Bars - Mount in the supply and return openings
to prevent entry into the duct work.

• Flue Exhaust Extension Kit - In locations with wind or
weather conditions which may interfere with proper
exhausting of furnace combustion products, this kit can be
installed to prevent the flue exhaust from entering nearby
fresh air intakes.

Sensor - Senses CO2 levels and automatically

• CO

2

overrides the economizer when levels rise above the
present limits.

8 Johnson Controls Unitary Products

251933-YTG-X-0615

• Coil Guard - Customers can purchase a coil guard kit to
protect the condenser coil from damage. This is not a hail
guard kit.

• Hail Guard - Hail Guard kit is available to prevent unit
from hail damage. This is a sloped hood that fits above
the coil.

• Gas Piping Kit - This kit supplies all necessary fittings
and shut off valve.

Guide Specifications

General

Units shall be manufactured by Johnson Controls Unitary
Products in an ISO 9001 certified facility.

York's ZE/ZF/ZR/XN/XP units are convertible single package
units. Although the units are primarily designed for curb
mounting on a roof, they can also be slab-mounted at ground
level or set on steel beams above a finished roof. Cooling only,
cooling with gas heat and cooling with electric heat models are
available with a wide variety of factory-mounted options and
field-installed accessories to make them suitable for almost
every application. All units are self-contained and assembled on
full perimeter base rails with holes in the four corners for
overhead rigging. Every unit is completely piped, wired,
charged and tested at the factory to simplify the field installation
and to provide years of dependable operation. All models
(including those with an economizer) are suitable for either
bottom or horizontal duct connections. Models with power
exhaust are suitable for bottom duct connections only. For
bottom duct, remove the sheet metal panels from the supply
and return air openings through the base of the unit. For
horizontal duct, remove the supply and return air panels on the
rear of the unit.

All non-Scroll compressors include crankcase heaters and all
compressors have internal pressure relief. Every refrigerant
circuit includes a liquid line filter-drier, a discharge line high
pressure switch and a suction line with a freezestat and low
pressure/loss of charge switch.The unit control circuit includes
a 75 VA transformer, a 24-volt circuit breaker and a relay board
with a compressor lockout circuit, a terminal strip for thermostat
wiring, plus an additional set of pin connectors to simplify the
interface of additional field controls. All models are CSA listed.
All models include a 1-year limited warranty on the complete
unit. Compressors and electric heater elements carry a 5-year
warranty. Aluminized steel and Stainless steel tubular heat
exchangers carry a 10-year warranty.

Cooling only or Cooling with Electric Heat shall have 11.2 EER,
6 Ton Cooling with Gas Heat shall have 11.0 EER. They shall
have built-in field convertible duct connections for down
discharge supply/return or horizontal discharge supply/return,
and be available with factory installed options or field installed
accessories. The units shall be factory wired, piped, charged
with R-410A refrigerant and factory tested prior to shipment. All
unit wiring shall be both numbered and color coded. All units
the cooling performance shall be rated in accordance with DOE
and AHRI test procedures. Units shall be CSA listed, classified
to ANSI Z21.47, UL 1995/CSA No. 236 standards.

Unit Cabinet

Unit cabinet shall be constructed of galvanized steel, with
exterior surfaces coated with a non-chalking, powdered paint
finish, certified at 1000 hours salt spray test per ASTMB117
standards. Indoor blower section shall be insulated with a
minimum 1/2” thick insulation, coated on the airside. Aluminum
foil faced insulation shall be used in the furnace compartment
and be fastened with ridged fasteners to prevent insulation from
entering the air stream. Cabinet panels shall be “large” size,
easily removable for servicing and maintenance. Full perimeter
base rails shall be provided to assure reliable transit of
equipment, overhead rigging and proper sealing on roof curb
applications. Disposable 1" filters shall be furnished and be
accessible through a removable access door, sealed airtight.
Units filter track shall be designed to accommodate either 1" or
2" filters. Fan performance measuring ports shall be provided
on the outside of the cabinet to allow accurate air
measurements of evaporator fan performance without removing
panels or creating air by-pass of the coils. Condensate pan
shall be internally sloped and conform to ASHRAE 62-89 self­draining standards. Condensate connection shall be a minimum
of 3/4” I.D. female and be a ridged mount connection.

Indoor (Evaporator) Fan Assembly

The indoor fan shall be a factory installed direct-drive or belt­drive assembly that includes an adjustable pitch motor pulley.
Job site selected (B.H.P.) brake horsepower shall not exceed
the motors nameplate horsepower rating, plus the service
factor. Units shall be designed not to operate above service
factor. Fan wheel shall be double-inlet type with forward-curved
blades, dynamically balanced to operate smoothly throughout
the entire range of operation. Airflow design shall be constant
air volume. Bearings shall be sealed and permanently
lubricated for longer life and no maintenance.

Outdoor (Condenser) Fan Assembly

Description

Units shall be factory-assembled, single packaged, Electric
Cooling/Gas Heat, Electric Cooling/Optional Electric Heat, Heat
Pump/Optional Electric Heat are designed for outdoor mounted
installation.

The 3 ton, 4 ton and 5 ton units shall have minimum SEER
rating of 13.0 with heat pumps having a 7.7 H.S.P.F. The 6 Ton

Johnson Controls Unitary Products 9

The outdoor fan shall be of the direct-driven propeller type,
discharge air vertically, have aluminum blades riveted to a
corrosion resistant steel spider bracket and shall be
dynamically balanced for smooth operation. The outdoor fan
motor shall be totally enclosed with permanently lubricated
bearings, internally protected against overload conditions and
staged independently.

251933-YTG-X-0615

Refrigerant Components

Compressor:

a. Shall be internally protected with internal high-pressure

relief and over temperature protection.

b. Shall have internal spring isolation and sound muffling to

minimize vibration and noise, and be externally isolated
on a dedicated, independent mounting.

Coils:

a. Evaporator coils shall have aluminum plate fins

mechanically bonded to seamless internally enhanced
copper tubes with all joints brazed. Special Phenolic
coating shall be available as a factory option.

b. Evaporator coils shall be of the direct expansion, draw-

thru design.

c. Condenser coils shall have aluminum plate fins

mechanically bonded to seamless internally enhanced
copper tubes with all joints brazed or Micro-Channel
aluminum tube, aluminum fins.

d. Condenser coils shall be of the direct expansion, draw-

thru design.

Refrigerant Circuit and Refrigerant Safety Components shall
include:

a. Independent fixed-orifice or thermally operated

expansion devices.

b. Filter drier/strainer to eliminate any moisture or foreign

matter.

c. Accessible service gage connections on both suction

and liquid lines to charge, evacuate, and measure
refrigerant pressure during any necessary servicing or
troubleshooting, without losing charge.

d. The refrigeration system shall provide at least 15°F of

sub-cooling at design conditions.

i. Standard controls shall include anti-short cycle and low

voltage protection, and permit cooling operation down to
0°F.

j. Control board shall monitor each refrigerant safety switch

independently.

k. Control board shall retain last 5 fault codes in non volatile

memory which will not be lost in the event of a power loss.

Gas Heating Section (Single Or 2 Stage)

Shall be designed with induced draft combustion with post
purge logic, energy saving direct spark ignition, and redundant
main gas valve. Venter wheel shall be constructed of stainless
steel for corrosion resistance. The heat exchanger shall be of
the tubular type, constructed of T1-40 aluminized steel for
corrosion resistance and allowing minimum mixed air entering
temperature of 25°F. Burners shall be of the inshot type,
constructed of aluminum coated steel and contain air mixture
adjustments. All gas piping shall enter the unit cabinet at a
single location through either the side or curb without any field
modifications. Integrated control boards shall provide timed
control of evaporator fan functioning and burner ignition.
Heating section shall be provided with the following minimum
protection:

a. Primary and auxiliary high-temperature limit switches.
b. Induced draft motor speed sensor.
c. Flame roll out switch.
d. Flame proving controls.
e. If any of the above safety devices trip, a LED (light-

emitting diode) indicator shall flash a diagnostic code that
indicates which safety switch has tripped.

st

NOTE: All 2 Stage Gas Heat, 60% Capacity 1

Stage, 40%

Capacity 2nd Stage.

Electric Heating Section

Unit Controls

An electric heating section, with nickel chromium elements,
shall be provided in a range of 5 thru 30 KW, offering two

a. Unit shall be complete with self-contained low-voltage

control circuit protected by a resettable circuit breaker on
the 24-volt transformer side.

b. Unit shall incorporate a lockout circuit which provides

reset capability at the space thermostat or base unit,
should any of the following standard safety devices trip

and shut off compressor.
c. Loss-of-charge/Low-pressure switch.
d. High-pressure switch.
e. Freeze-protection thermostat, evaporator coil.
f. Unit shall incorporate “AUTO RESET” compressor over

temperature, over current protection.
g. Unit shall operate with conventional thermostat designs

and have a low voltage terminal strip for easy hook-up.

stages of capacity - 16 KW and above on 208/230 volt heaters
and 20 KW and above on 460 and 575 volt heaters. The
heating section shall have a primary limit control(s) and
automatic reset to prevent the heating element system from
operating at an excessive temperature. The heating section
assembly shall slide out of the unit for easy maintenance and
service. Units with Electric Heating shall be wired for a single
point power supply with branch circuit fusing (where required).

Unit Operating Characteristics

Unit shall be capable of starting and running at 125°F outdoor
temperature, exceeding maximum load criteria of AHRI
Standard 210/240. The compressor, with standard controls,
shall be capable of operation down to 0°F outdoor temperature.
Unit shall be provided with fan time delay to prevent cold air
delivery before heat exchanger warms up (Gas heat only).

h. Unit control board shall have on-board diagnostics and

fault code display.

10 Johnson Controls Unitary Products

251933-YTG-X-0615

Electrical Requirements

All unit power wiring shall enter unit cabinet at a single factory
provided location and be capable of side or bottom entry, to
minimize roof penetrations and avoid unit field modifications.
Separate side and bottom openings shall be provided for the
control wiring.

Standard Limited Warranties

• Compressor 5 Years

• Heat Exchanger 10 Years

• Electric Heat Element 5 Years

• Other Parts 1 Year

Optional Outdoor Air

Shall be made available by either/or:

• Dry Bulb Automatic Economizer - Outdoor and return air

dampers that are interlocked and positioned by a fully­modulating, spring-return damper actuator. The maximum
leakage rate for the outdoor air intake dampers shall be
designed to meet ASHRAE 90.1-2010, AMCA 511 Class
1A damper, and the International Energy Conservation
Code (IECC) certification requirements by achieving
leakage rates of 3 cfm/sq. ft. at 1" of static pressure.
Changeover from compressor to economizer operation
shall be provided by an integral electronic enthalpy control
that feeds input into the basic module. The outdoor intake
opening shall be covered with a rain hood that matches the
exterior of the unit. Water eliminator/filters shall be
provided. Simultaneous economizer/compressor operation
is also possible. Dampers shall fully close on power loss.
Available with barometric relief and power exhaust..

• Motorized Outdoor Air Dampers - Outdoor air dampers

are positioned by a 2-position, spring-return damper
actuator. A unit-mounted potentiometer shall be provided
to adjust the outdoor damper assembly to take in the
design CFM of outdoor air to meet the ventilation
requirements of the conditioned space during normal
operation. Whenever the indoor fan motor is energized,
the dampers open up to one of two pre-selected positions

- regardless of the outdoor air enthalpy. Dampers return to
the fully closed position when the indoor fan motor is de­energized. Dampers shall fully close on power loss.

Other Pre-engineered Accessories Available

• Roof Curb - 14"and 8” high, full perimeter curb with wood

nailer (shipped knocked-down).

• Barometric Relief Damper - Contains a rain hood, air

inlet screen, exhaust damper and mounting hardware.
Used to relieve internal air pressure through the unit.

• Propane Conversion Kit - Contains new orifices and gas

valve parts to convert from natural to L.P. gas. One per
unit required.

• High Altitude - Natural Gas - Contains orifices required
for applications between 2000 and 6000 feet altitude.

• High Altitude - Propane Gas - Contains orifice s requ ired
for applications between 2000 and 6000 feet altitude.
Must be used with propane conversion kit.

• Low Nox - Required to reduce the emission of nitrogen
oxides below 40 nanograms per joule.

• Gas Piping - Contains 1/2” pipe nipples, fittings and gas
cock (including panel assess gaskets) required for bottom
gas supply connection with external shut off.

• Power Exhaust Option - To work in conjunction with
economizers.

• Electric Heaters

• Economizer/motorized Damper Rain Hood - Contains
all hood panels and the hardware for assembling.

• Manual Outdoor Air Damper

• Coil Guard Kit - Guard for cooling coil.

• Hail Guard

• Flue Exhaust Extension

OTHER FACTORY INSTALLED OPTIONS

• Power Exhaust Option - To work in conjunction with
economizers.

• Stainless Steel Heat Exchanger

• Stainless Steel Drain Pan

• Bottom Drain Connection

• Technicoat Phenolic Coated Condenser And
Evaporator Coil

• Electronic Single Enthalpy Economizer

• Dirty Filter Switch

• Phase Monitor

• Coil Guard

• Powered GFI Convenience Outlet

• Non-powered GFI Convenience Outlet

• BAS Controls - Simplicity® SE with BAS
Communication (BACnet MS/TP, Modbus, and
Johnson Controls N2) Option, CPC, HONEYWELL,
NOVAR, YORK

• Bas Ready Economizer (2-10 V.D.C. Actuator Without
a Controller)

• Hinged Filter Door Access And Toolless Access
Panels

• 2" Pleated Filters, MERV 7

• Disconnect Switch

• Supply Air Smoke Detector

• Return Air Smoke Detector

• Direct Drive Or Belt Drive Blower With High Static
Drive Option

• Hot Gas Reheat with Hot Gas Bypass (Not available
on 6 Ton)

Johnson Controls Unitary Products 11

251933-YTG-X-0615

Physical Data

ZE036-060 Physical Data

Component

Nominal Tonnage 3 4 5

ARI COOLING PERFORMANCE

Gross Capacity @ AHRI A point (Btu) 36600 49100 59000
AHRI net capacity (Btu) 35500 47500 57000
EER 12.0 12.0 11.8
SEER 14.0 14.0 14.0
IPLV --­CFM 1200 1450 1680
System power (KW) 2.96 3.96 4.83
Refrigerant type R-410A R-410A R-410A
Refrigerant charge (lb-oz)
System 1 4-4 5-6 6-6

AHRI HEATING PERFORMANCE

Heating model N04 N08 D06 D10 N06 N10 D06 D10 N08 N10 D06 D10
Heat input (K Btu) 50 100 75 115 75 125 75 125 100 125 75 125
Heat output (K Btu) 40 80 60.8 92 60 100 60.8 100.6 80 100 60.8 100.6
AFUE % 8181 - - 8181 - - 8181 - ­Steady state efficiency (%) - - 81.1 80.2 - - 81.1 80.5 - - 81.1 80.5
No. burners 243535354535
No. stages 1 1 2 2 1 1 2 2 1 1 2 2
Temperature Rise Range (ºF) 15-45 45-75 35-70 55-90 25-70 45-75 25-70 45-75 25-55 35-75 20-55 35-75
Gas Limit Setting (ºF) - Direct Drive 240 170 210 200 210 165 210 165 170 165 210 165
Gas Limit Setting (ºF) - Belt Drive 240 210 240 200 240 210 240 210 210 210 210 210
Gas piping connection (in.) 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2
DIMENSIONS (inches)
Length 82 1/4 82 1/4 82 1/4
Width 44 7/8 44 7/8 44 7/8
Height 32 5/8 32 5/8 32 5/8

OPERATING WT. (lbs.) 470 598 632

COMPRESSORS

Type SCROLL SCROLL SCROLL
Quantity 1 1 1
Unit Capacity Steps (%) 100 100 100

CONDENSER COIL DATA

Face area (Sq. Ft.) 16.3 16.3 16.3
Rows 111
Fins per inch 23 23 23
Tube diameter (in.) 0.7 1 / 18 0.71 / 18 1.00 / 25.4
Circuitry Type 2-pass Microchannel 2-pass Microchannel 2-pass Microchannel

EVAPORATOR COIL DATA

Face area (Sq. Ft.) 5.06 5.06 5.06
Rows 344
Fins per inch 13 13 13
Tube diameter 0.375 0.375 0.375
Circuitry Type Intertwined Intertwined Intertwined
Refrigerant control Orifice Orifice TXV

ZE036 ZE048 ZE060

Models

12 Johnson Controls Unitary Products

ZE036-060 Physical Data (Continued)

251933-YTG-X-0615

Component

Nominal Tonnage 3 4 5

CONDENSER FAN DATA

Quantity of fans 1 1 1
Fan diameter (Inch) 24 24 24
Type Prop Prop Prop
Drive type Direct Direct Direct
Quantity of motors 1 1 1
Motor HP each 1/2 1/2 1/2
No. speeds 1 1 1
RPM 1090 1090 1100
CFM 4000 4000 4200

BELT DRIVE EVAP FAN DATA

Quantity 1 1 1
Fan Size (Inch) 12 x 10 12 x 10 12 x 10
Type Centrifugal Centrifugal Centrifugal
Motor Sheave 1VL44 1VP56 1VL44 1VP56 1VL44 1VP56
Blower Sheave AK64 AK66 AK56 AK61 AK56 AK56
Belt A37 A39 A36 A38 A36 A38
Motor HP each 1-1/2 1-1/2 1-1/2 1-1/2 1-1/2 2
RPM 1740 1740 1740
Frame size 56 56 56

DIRECT DRIVE EVAP FAN DATA

Quantity 1 1 1
Fan Size (Inch) 12 x 10 12 x 10 12 x 10
Type Centrifugal Centrifugal Centrifugal
Motor HP each 1/2 1 1
RPM 1050 1050 1050
FILTERS
15" x 20" x 1" or 2" 2 2 2
14" x 25" x 1" or 2" 1 1 1
NOTE: All 2 Stage Gas Heat, 60% Capacity 1

st

ZE036 ZE048 ZE060

Stage , 40% 2nd Stage

Models

Johnson Controls Unitary Products 13

251933-YTG-X-0615

ZF036-060 Physical Data

Component

Nominal Tonnage 3.0 4.0 5.0

AHRI COOLING PERFORMANCE

Gross Capacity @ AHRI A point (Btu)
AHRI net capacity (Btu)
EER
SEER
IPLV
CFM
System power (KW)
Refrigerant type
Refrigerant charge (lb-oz)

System 1 4-4 5-8 5-8

AHRI HEATING PERFORMANCE

Heating model
Heat input (K Btu)
Heat output (K Btu)
AFUE %
Steady state efficiency (%)
No. burners
No. stages
Temperature Rise Range (ºF) 15-45 45-75 35-70 55-90 25-70 45-75 25-70 45-75 25-55 35-75 20-55 35-75
Gas Limit Setting (ºF) - Direct Drive 240 170 210 200 210 165 210 165 170 165 210 165
Gas Limit Setting (ºF) - Belt Drive 240 210 240 200 240 210 240 210 210 210 210 210
Gas piping connection (in.)

DIMENSIONS (inches)

Length
Width
Height

OPERATING WT. (lbs.)

COMPRESSORS

Type
Quantity
Unit Capacity Steps (%)

CONDENSER COIL DATA

Face area (Sq. Ft.) 16.3 16.3 16.3
Rows
Fins per inch
Tube diameter (in.)
Circuitry Type

EVAPORATOR COIL DATA

Face area (Sq. Ft.)
Rows
Fins per inch
Tube diameter
Circuitry Type
Refrigerant control

N04 N08 D06 D10 N06 N10 D06 D10 N08 N10 D06 D10

50 100 75 115 75 125 75 125 100 125 75 125
40 80 60.8 92 60 100 60.8 100.6 80 100 60.8 100.6

- - - - - - - - - - --

- - 80.0 80.0 - - 80.0 80.0 - - 80.0 80.0
2 4 3 5 3 5 3 5 4 5 35
1 1 2 2 1 1 2 2 1 1 22

1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2

ZF036 ZF048 ZF060

37000 49300 59000
35500 47500 56500

11.0 11.0 10.8

13.0 13.0 13.0

- - -

1200 1500 1750

3.23 4.32 5.23

R-410A R-410A R-410A

82 1/4 82 1/4 82 1/4
44 7/8 44 7/8 44 7/8
32 5/8 32 5/8 32 5/8

468 541 569

Recip Recip Recip

1 1 1

100 100 100

1 1 1

23 23 23

0.71 / 18 0.71 / 18 0.71 / 18

2-pass Microchannel 2-pass Microchannel 2-pass Microchannel

5.06 5.06 5.06
3 3 4

13 13 13

0.375 0.375 0.375

Intertwined Intertwined Intertwined

Orifice Orifice Orifice

Models

14 Johnson Controls Unitary Products

ZF036-060 Physical Data (Continued)

251933-YTG-X-0615

Component

Nominal Tonnage 3.0 4.0 5.0

CONDENSER FAN DATA

Quantity
Fan diameter (Inch)
Type
Drive type
Quantity of motors
Motor HP each
No. speeds
RPM
CFM

BELT DRIVE EVAP FAN DATA

Quantity
Fan Size (Inch)
Type
Motor Sheave 1VL44 1VP56 1VL44 1VP56 1VL44 1VP56
Blower Sheave AK64 AK66 AK56 AK61 AK56 AK56
Belt A37 A39 A36 A38 A36 A38
Motor HP each 1-1/2 1-1/2 1-1/2 1-1/2 1-1/2 2
RPM
Frame size

DIRECT DRIVE EVAP FAN DATA

Quantity
Fan Size (Inch)
Type
Motor HP each
RPM

FILTERS

15” x 20” x 1” or 2”
14” x 25” x 1” or 2”

ZF036 ZF048 ZF060

1 1 1

24 24 24

Prop Prop Prop

Direct Direct Direct

1 1 1

1/2 1/2 1/2

1 1 1

1090 1090 1090
3800 4200 4200

1 1 1

11 x 10 11 x 10 11 x 10

Centrifugal Centrifugal Centrifugal

1725 1725 1725

56 56 56

1 1 1

12 x 10 12 x 10 12 x 10

Centrifugal Centrifugal Centrifugal

1/2 1 1

1050 1050 1050

2 2 2
1 1 1

Models

NOTE: All 2 Stage Gas Heat, 60% Capacity 1

st

Stage, 40% Capacity 2nd Stage.

Johnson Controls Unitary Products 15

251933-YTG-X-0615

ZF072 Physical Data

Component

Models

ZF072

Nominal Tonnage 6.0

AHRI COOLING PERFORMANCE

Gross Capacity @ AHRI A point (Btu) 70360
AHRI net capacity (Btu) 68000

1

EER 11.2

/ 11.0

2

IEER 11.3
CFM 2000
System power (KW) 6.07
Refrigerant type R-410A
Refrigerant charge (lb-oz)

System 1 6-4

AHRI HEATING PERFORMANCE

Heating model N08 N10 D06 D10
Heat input (K Btu) 100 125 75 125
Heat output (K Btu) 80 100 60.8 100.6
AFUE % ---­Steady state efficiency (%) - - 80.0 80.0
No. burners 4535
No. stages 1122
Temperature Rise Range (ºF) 25-55 30-75 15-45 30-75
Gas Limit Setting (ºF) - Direct Drive 170 165 210 165
Gas Limit Setting (ºF) - Belt Drive 210 210 210 210
Gas piping connection (in.) 1/2 1/2 1/2 1/2

DIMENSIONS (inches)

Length 82 1/4
Width 44 7/8
Height 32 5/8

OPERATING WT. (lbs.) 640

COMPRESSORS

Type Scroll
Quantity 1
Unit Capacity Steps (%) 100

CONDENSER COIL DATA

Face area (Sq. Ft.) 16.3
Rows 1
Fins per inch 23
Tube diameter (in.) 1.0 / 25.4
Circuitry Type 2-pass Microchannel

EVAPORATOR COIL DATA

Face area (Sq. Ft.) 5.06
Rows 4
Fins per inch 13
Tube diameter 0.375
Circuitry Type Intertwined
Refrigerant control Fixed Orifice

16 Johnson Controls Unitary Products

ZF072 Physical Data (Continued)

251933-YTG-X-0615

Component

Models

ZF072

Nominal Tonnage 6.0

CONDENSER FAN DATA

Quantity 1
Fan diameter (Inch) 24
Type Prop
Drive type Direct Drive
No. speeds 1
Number of motors 1
Motor HP each 1/2

3

1/2

4

RPM 1100 1090
CFM 4200 4200

BELT DRIVE EVAP FAN DATA

Quantity 1
Fan Size (Inch) 12 x 10
Type Centrifugal
Motor Sheave 1VL44 1VP56
Blower Sheave AK56 AK56
Belt A36 A38
Motor HP each 1-1/2 3
RPM 1725
Frame size 56

DIRECT DRIVE EVAP FAN DATA

Quantity 1
Fan Size (Inch) 12 x 10
Type Centrifugal
Motor HP each 1
RPM 1050

FILTERS

15” x 20” x 1” or 2” 2
14” x 25” x 1” or 2” 1

1. Cooling Only or Cooling with Electric Heat Unit

2. Cooling with Gas Heat Unit

3. Cooling Only or Cooling with Electric Heat Unit (ECM O.D. Fan Motor)

4. Cooling with Gas Heat Unit (PSC O.D. Fan Motor)
NOTE: All 2 Stage Gas Heat, 60% Capacity 1st Stage, 40% Capacity 2nd Stage.

Johnson Controls Unitary Products 17

251933-YTG-X-0615

ZR036-060 Physical Data

Component

Nominal Tonnage 3.0 4.0 5.0

AHRI COOLING PERFORMANCE

Gross Capacity @ AHRI A point (Btu) 36300 49600 60800
AHRI net capacity (Btu) 35000 48000 58500
EER 11.2 11.2 11.2
SEER 13.0 13.0 13.0
IPLV --­CFM 1200 1600 2000
System power (KW) 3.13 4.18 5.3
Refrigerant type R-410a R-410a R-410a
Refrigerant charge (lb-oz)

System 1 11-2 12-4 11-12

AHRI HEATING PERFORMANCE

Heating model N04 N08 D06 D10 N06 N10 D06 D10 N08 N10 D06 D10
Heat input (K Btu) 50 100 75 115 75 125 75 125 100 125 75 125
Heat output (K Btu) 40 80 60.8 92 60 100 60.8 100.6 80 100 60.8 100.6
AFUE % -----------­Steady state efficiency (%) - - 80.0 80.0 - - 80.0 80.0 - - 80.0 80.0
No. burners 243535354535
No. stages 112211221122
Temperature Rise Range (ºF) 15-45 45-75 35-70 55-90 25-70 45-75 25-70 45-75 25-55 35-75 20-55 35-75
Gas Limit Setting (ºF) - Direct Drive 240 170 210 200 210 165 210 165 170 165 210 165
Gas Limit Setting (ºF) - Belt Drive 240 210 240 200 240 210 240 210 210 210 210 210
Gas piping connection (in.) 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2

DIMENSIONS (inches)

Length 82 1/4 82 1/4 82 1/4
Width 44 7/8 44 7/8 44 7/8
Height 32 5/8 32 5/8 32 5/8

OPERATING WT. (lbs.) 575 585 590

COMPRESSORS

Type Scroll Scroll Scroll
Quantity 1 1 1
Unit Capacity Steps (%) 100 100 100

CONDENSER COIL DATA

Face area (Sq. Ft.) 16.9 16.9 16.9
Rows 222
Fins per inch 18 18 18
Tube diameter (in.) 3/8 3/8 3/8
Circuitry Type Split-face Split-face Split-face

EVAPORATOR COIL DATA

Face area (Sq. Ft.) 5.06 5.06 5.06
Rows 334
Fins per inch 13 13 13
Tube diameter 0.375 0.375 0.375
Circuitry Type Split-face Split-face Split-face
Refrigerant control TXV TXV TXV

ZR036 ZR048 ZR060

Models

18 Johnson Controls Unitary Products

ZR036-060 Physical Data (Continued)

251933-YTG-X-0615

Component

Nominal Tonnage 3.0 4.0 5.0

CONDENSER FAN DATA

Quantity 1 1 1
Fan diameter (Inch) 24 24 24
Type Prop Prop Prop
Drive type Direct Drive Direct Drive Direct Drive
No. speeds 1 1 1
Number of motors 1 1 1
Motor HP each 1/2 1/2 1/2
RPM 1090 1090 1090
CFM 4200 4200 4200

BELT DRIVE EVAP FAN DATA

Quantity 1 1 1
Fan Size (Inch) 11 x 10 11 x 10 11 x 10
Type Centrifugal Centrifugal Centrifugal
Motor Sheave 1VL44 1VP56 1VL44 1VP56 1VL44 1VP56
Blower Sheave AK64 AK66 AK56 AK61 AK56 AK56
Belt A37 A39 A36 A38 A36 A38
Motor HP each 1-1/2 1-1/2 1-1/2 1-1/2 1-1/2 2
RPM 1725 1725 1725
Frame size 56 56 56

DIRECT DRIVE EVAP FAN DATA

Quantity 1 1 1
Fan Size (Inch) 11 x 10 11 x 10 11 x 10
Type Centrifugal Centrifugal Centrifugal
Motor HP each 1/2 1 1
RPM 1050 1050 1050

FILTERS

15” x 20” x 1” or 2” 2 2 2
14” x 25” x 1” or 2” 1 1 1

ZR036 ZR048 ZR060

Models

NOTE: All 2 Stage Gas Heat, 60% Capacity 1

st

Stage, 40% Capacity 2nd Stage.

Johnson Controls Unitary Products 19

251933-YTG-X-0615

XN036-060 Physical Data

Component

Nominal Tonnage 3 4 5

AHRI COOLING PERFORMANCE

Gross Capacity @ AHRI A point (Btu) 38,400 48,700
AHRI net capacity (MBH) 37,000 47,000
EER 12.0 11.8
SEER 14.0 14.0
CFM 1200 1450
System power (KW) 3.08 3.98
Refrigerant type R410A R410A

Refrigerant charge (lb-oz)
System 1 13-8 13-10

ARI HEATING PERFORMANCE

47ºF capacity rating (MBH) 36,000 44,000
System power (KW) / COP 3.15 (kW) / 3.35 4.03 (kW) / 3.20
17ºF capacity rating (MBH) 19,000 24,900
System power (KW) / COP 2.5 (kW) / 2.2 3.48 (kW) / 2.10
HSPF (Btu/Watts-hr) 8.00 8.00

DIMENSIONS (inches)

Length 82-1/4 82-1/4
Width 44-7/8 44-7/8
Height 32-5/8 32-5/8

OPERATING WT. (lbs.) 610 616

COMPRESSORS

Type SCROLL SCROLL
Quantity 1 1

CONDENSER COIL DATA

Face area (Sq. Ft.) 16.88 16.88
Rows 2 2
Fins per inch 18 18
Tube diameter 3/8 3/8
Circuitry Type Split-face Split-face

Refrigerant control TXV TXV TXV

EVAPORATOR COIL DATA

Face area (Sq. Ft.) 5.06 5.06
Rows 4 4
Fins per inch 13 13
Tube diameter 0.375 0.375
Circuitry Type Split-face Split-face
Refrigerant control TXV TXV

XN036 XN048 XN060

Models

5,750

55,400

11.0

14.0

1275/1850

5.04

R410A

11-10

51,500

4.5 (kW) / 3.35
30,000

4.11 (kW) / 2.14

8.00

82-1/4
44-7/8
32-5/8

620

SCROLL

1

16.88
2

18

3/8

Split-face

5.06
4

13

0.375

Split-face

TXV

20 Johnson Controls Unitary Products

XN036-060 Physical Data (Continued)

251933-YTG-X-0615

Component

Nominal Tonnage 3 4 5

CONDENSER FAN DATA

Quantity 1 1
Fan diameter (Inch) 24 24
Type Prop Prop
Drive type DIRECT DRIVE DIRECT DRIVE
No. speeds 1 1
Number of motors 1 1
Motor HP each 1/4 1/4
RPM 850 850
CFM 3000 3300

BELT DRIVE EVAP FAN DATA

Quantity 1 1
Fan diameter (Inch) 12 x 10 12 x 10
Type Centrifugal Centrifugal

Motor Sheave 1VL44 1VP56 1VL44 1VP56 1VL44 1VP56
Blower Sheave AK64 AK66 AK56 AK61 AK56 AK56
Belt A37 A39 A36 A38 A36 A38
Motor HP each 1-1/2 1-1/2 1-1/2 1-1/2 1-1/2 2

RPM 1740 1740
Frame size 56 56

DIRECT DRIVE EVAP FAN DATA

Quantity 1 1
Fan Size (Inch) 12 x 10 12 x 10
Type Centrifugal Centrifugal
Motor HP each 1/2 1
RPM 1050 1050

FILTERS

15" x 20" x 1" or 2" 2 2
14" x 25" x 1" or 2" 1 1

XN036 XN048 XN060

Models

1

24

Prop

DIRECT DRIVE

2
1

1/2

850/1100

2800/3800

1

12 x 10

Centrifugal

1740

56

1

12 x 10

Centrifugal

1

1050

2
1

Johnson Controls Unitary Products 21

251933-YTG-X-0615

XP036-060 Physical Data

Component

Nominal Tonnage 3.0 4.0 5.0

AHRI COOLING PERFORMANCE

Gross Capacity @ AHRI A point (Btu) 37,500 46500 60100
AHRI net capacity (Btu) 36,000 44500 57500
EER 11.4 11.0 10.6
SEER 13.0 13.0 13.0
CFM 1300 1600 1850
System power (KW) 3.30 4.05 5.42
Refrigerant type R410A R410A R-410A
Refrigerant charge (lb-oz) 13-8 13-12 12-10

AHRI HEATING PERFORMANCE

47°F capacity rating (MBH) 35,000 41,000 56500
System power (KW) / COP 3.10 (kW) / 3.30 4.0 (kW) / 3.20 5.4 (kW) / 3.10
17°F capacity rating (MBH 21,200 22,400 34400
System power (KW) / COP 2.89(kW) / 2.15 3.8 (kW) / 2.10 4.75 (kW) / 2.10
HSPF (Btu/Watts-hr) 7.70 7.70 7.70

DIMENSIONS (inches)

Length 82-1/4 82-1/4 82-1/4
Width 44-7/8 44-7/8 44-7/8
Height 32-5/8 32-5/8 32-5/8

OPERATING WT. (lbs.) 575 585 590

COMPRESSORS

Type Scroll Scroll Scroll
Quantity 1 1 1

CONDENSER COIL DATA

Face area (Sq. Ft.) 16.88 16.88 16.88
Rows 222
Fins per inch 18 18 18
Tube diameter 3/8 3/8 3/8
Circuitry Type Split-face Split-face Split-face

EVAPORATOR COIL DATA

Face area (Sq. Ft.) 5.06 5.06 5.06
Rows 444
Fins per inch 13 13 13
Tube diameter 0.375 0.375 0.375
Circuitry Type Split-face Split-face Split-face
Refrigerant control TXV TXV TXV

XP036 XP048 XP060

Models

22 Johnson Controls Unitary Products

XP036-060 Physical Data (Continued)

251933-YTG-X-0615

Component

Nominal Tonnage 3.0 4.0 5.0

CONDENSER FAN DATA

Quantity 1 1 1
Fan diameter (Inch) 24 24 24
Type Prop Prop Prop
Drive type Direct Drive Direct Drive Direct Drive
No. speeds 1 1 1
Number of motors 1 1 1
Motor HP each 1/4 1/4 1/2
RPM 850 850 1090
Nominal total CFM 3275 3800 4200

BELT DRIVE EVAP FAN DATA

Quantity 1 1 1
Fan Size (Inch) 11 x 10 11 x 10 11 x 10
Type Centrifugal Centrifugal Centrifugal
Motor Sheave 1VL44 1VP56 1VL44 1VP56 1VL44 1VP56
Blower Sheave AK64 AK66 AK56 AK61 AK56 AK56
Belt A37 A39 A36 A38 A36 A38
Motor HP each 1-1/2 1-1/2 1-1/2 1-1/2 1-1/2 2
RPM 1725 1725 1725
Frame size 56 56 56

DIRECT DRIVE EVAP FAN DATA

Quantity 1 1 1
Fan Size (Inch) 11 x 10 11 x 10 11 x 10
Type Centrifugal Centrifugal Centrifugal
Motor HP each 3/4 1 1
RPM 1050 1050 1050

FILTERS

15” x 20” x 1” or 2” 2 2 2
14” x 25” x 1” or 2” 1 1 1

XP036 XP048 XP060

Models

Johnson Controls Unitary Products 23

251933-YTG-X-0615

ZF/ZR/XP036-072 Unit Limitations

Size

(Tons)

ZF/ZR/XP036

(3.0)

ZF/ZR/XP048

(4.0)

ZF/ZR/XP060

(5.0)

ZF072

(6.0)

Unit Voltage

208/230-3-60 187 252 125

460-3-60 432 504 125
575-3-60 540 630 125

208/230-3-60 187 252 125

460-3-60 432 504 125
575-3-60 540 630 125

208/230-3-60 187 252 125

460-3-60 432 504 125
575-3-60 540 630 125

208/230-3-60 187 252 125

460-3-60 432 504 125
575-3-60 540 630 125

ZE/XN036-060 Unit Limitations

Size

(Tons)

ZE/XN036

(3.0)

ZE/XN048

(4.0)

ZE/XN060

(5.0)

Unit Voltage

208/230-1-60 187 252 125
208/230-3-60 187 252 125

460-3-60 432 504 125

575-3-60 540 630 125
208/230-1-60 187 252 125
208/230-3-60 187 252 125

460-3-60 432 504 125

575-3-60 540 630 125
208/230-1-60 187 252 125
208/230-3-60 187 252 125

460-3-60 432 504 125

575-3-60 540 630 125

Unit Limitations

Applied Voltage Outdoor DB Temp

Min Max Max (°F)

Unit Limitations

Applied Voltage Outdoor DB Temp

Min Max Max (°F)

24 Johnson Controls Unitary Products

Capacity Performance

ZE036-060 Cooling Capacities

ZE036 (3.0 Ton)

Air on

Evaporator Coil

CFM

750

900

1050

1200

1350

1500

750

900

1050

1200

1350

1500

WB
(°F)

77 44.0 2.0 19.5 16.3 13.2 - - - 42.2 2.3 18.7 15.6 12.5 - - ­72 41.5 2.0 24.6 21.5 18.3 15.2 - - 39.2 2.2 23.6 20.4 17.3 14.1 - ­67 39.1 2.0 29.7 26.6 23.4 20.3 17.2 - 36.2 2.2 28.4 25.2 22.1 18.9 15.8 ­62 36.2 1.9 36.2 31.7 28.5 25.4 22.2 19.1 33.4 2.2 33.4 31.1 26.9 23.8 20.6 17.5
77 45.5 2.0 21.4 17.9 14.3 - - - 43.7 2.3 20.8 17.2 13.6 - - ­72 43.0 2.0 27.0 23.4 19.9 16.3 - - 40.6 2.2 26.1 22.5 18.9 15.3 - ­67 40.5 2.0 32.6 29.0 25.4 21.9 18.3 - 37.5 2.2 31.3 27.7 24.1 20.5 16.9 ­62 37.5 1.9 37.5 34.5 31.0 27.4 23.8 20.2 34.6 2.2 34.6 33.0 29.4 25.8 22.2 18.6
57 35.9 1.9 35.9 35.9 34.3 30.7 27.1 23.5 34.1 2.2 34.1 34.1 31.2 27.6 24.0 20.4
77 47.1 2.0 23.4 19.4 15.4 - - - 45.3 2.3 22.9 18.9 14.8 - - ­72 44.5 2.0 29.4 25.4 21.4 17.4 - - 42.0 2.2 28.6 24.6 20.5 16.4 - ­67 41.9 1.9 35.4 31.4 27.4 23.4 19.5 - 38.8 2.2 34.3 30.3 26.2 22.1 18.1 ­62 38.8 1.9 38.8 37.3 33.4 29.4 25.4 21.4 35.8 2.2 35.8 35.0 31.9 27.9 23.8 19.7
57 37.1 1.9 37.1 37.1 37.0 33.0 29.0 25.0 35.3 2.2 35.3 35.3 33.8 29.8 25.7 21.6
77 48.7 2.0 25.4 21.0 16.5 - - - 46.8 2.3 25.0 20.5 15.9 - - ­72 46.0 1.9 31.8 27.4 23.0 18.6 - - 43.4 2.2 31.2 26.6 22.1 17.6 - ­67 43.3 1.9 38.3 33.9 29.4 25.0 20.6 - 40.1 2.2 37.3 32.8 28.3 23.7 19.2 ­62 40.1 1.9 40.1 40.1 35.8 31.4 27.0 22.6 37.0 2.2 37.0 37.0 34.5 29.9 25.4 20.9
57 38.4 1.9 38.4 38.4 38.4 35.3 30.8 26.4 36.5 2.2 36.5 36.5 36.5 32.0 27.4 22.9
72 47.4 1.9 35.0 30.4 25.7 21.1 - - 44.2 2.2 33.4 28.5 23.5 18.6 - ­67 44.6 1.9 42.1 37.6 32.9 28.3 23.6 - 40.8 2.2 39.5 35.0 30.1 25.2 20.2 ­62 41.3 1.9 41.3 41.3 39.5 34.9 30.2 25.6 37.7 2.2 37.7 37.7 36.4 31.5 26.6 21.6
57 39.5 1.9 39.5 39.5 39.5 36.2 31.5 26.9 37.2 2.2 37.2 37.2 37.2 32.2 27.3 22.4
72 48.8 1.9 38.2 33.3 28.5 23.6 - - 45.1 2.2 35.7 30.3 25.0 19.6 - ­67 45.9 1.9 45.9 41.3 36.4 31.6 26.7 - 41.6 2.2 41.6 37.3 31.9 26.6 21.3 ­62 42.5 1.9 42.5 42.5 42.5 38.4 33.5 28.7 38.4 2.2 38.4 38.4 38.4 33.1 27.7 22.4
57 40.7 1.9 40.7 40.7 40.7 37.1 32.2 27.4 37.9 2.2 37.9 37.9 37.9 32.5 27.2 21.8

77 40.5 2.5 18.0 14.9 11.7 - - - 36.0 2.9 13.6 11.5 8.5 - - ­72 36.9 2.5 22.5 19.4 16.2 13.1 - - 33.0 2.9 19.9 16.8 13.7 10.7 - ­67 33.3 2.5 27.0 23.8 20.7 17.6 14.5 - 30.0 2.9 26.1 22.0 19.0 15.9 12.8 ­62 30.6 2.5 30.6 30.4 25.3 22.2 19.1 15.9 27.7 2.9 27.7 27.5 22.5 19.4 16.3 13.3
77 42.0 2.5 20.2 16.6 13.0 - - - 37.3 2.9 16.6 13.0 9.4 - - ­72 38.2 2.5 25.2 21.5 17.9 14.3 - - 34.2 2.9 22.5 18.9 15.3 11.7 - ­67 34.5 2.5 30.1 26.5 22.8 19.2 15.6 - 31.1 2.9 28.4 24.8 21.2 17.5 13.9 ­62 31.7 2.5 31.7 31.5 27.9 24.3 20.6 17.0 28.6 2.9 28.6 28.6 25.0 21.4 17.8 14.2
57 32.4 2.5 32.4 31.7 28.1 24.4 20.8 17.2 29.1 2.9 29.1 28.7 25.1 21.5 17.8 14.2
77 43.4 2.5 22.4 18.3 14.2 - - - 38.5 2.9 19.6 14.5 10.3 - - ­72 39.5 2.5 27.8 23.7 19.6 15.4 - - 35.3 2.9 25.1 21.0 16.8 12.7 - ­67 35.7 2.5 33.2 29.1 25.0 20.8 16.7 - 32.1 2.9 30.7 27.5 23.3 19.2 15.0 ­62 32.8 2.5 32.8 32.7 30.5 26.4 22.2 18.1 29.6 2.8 29.6 29.6 27.6 23.5 19.3 15.2
57 33.5 2.5 33.5 33.1 30.7 26.5 22.4 18.3 30.1 2.8 30.1 29.9 27.6 23.5 19.3 15.2
77 44.9 2.5 24.6 20.0 15.4 - - - 39.8 2.9 22.6 16.0 11.3 - - ­72 40.9 2.5 30.5 25.8 21.2 16.6 - - 36.5 2.9 27.8 23.1 18.4 13.7 - ­67 36.9 2.5 36.3 31.7 27.1 22.4 17.8 - 33.2 2.9 32.9 30.2 25.5 20.8 16.1 ­62 33.9 2.5 33.9 33.9 33.1 28.4 23.8 19.2 30.6 2.8 30.6 30.6 30.2 25.5 20.8 16.1
57 34.6 2.5 34.6 34.6 33.3 28.6 24.0 19.4 31.1 2.8 31.1 31.1 30.2 25.5 20.8 16.1
72 41.1 2.6 31.8 26.6 21.4 16.1 - - 36.8 2.9 29.4 24.1 18.9 13.7 - ­67 37.1 2.5 36.8 32.5 27.3 22.0 16.8 - 33.5 2.9 33.3 31.0 26.3 21.1 15.9 ­62 34.1 2.5 34.1 34.1 33.3 28.1 22.9 17.7 30.9 2.9 30.9 30.9 30.5 25.2 20.0 14.8
57 34.8 2.5 34.8 34.8 33.5 28.3 23.1 17.8 31.4 2.9 31.4 31.4 30.6 25.4 20.2 14.9
72 41.3 2.6 33.1 27.3 21.5 15.7 - - 37.1 2.9 31.0 25.2 19.5 13.7 - ­67 37.3 2.6 37.3 33.3 27.4 21.6 15.8 - 33.8 2.9 33.8 31.7 27.1 21.4 15.6 ­62 34.3 2.5 34.3 34.3 33.5 27.7 21.9 16.1 31.1 2.9 31.1 31.1 30.8 25.0 19.2 13.5
57 35.0 2.5 35.0 35.0 33.7 27.9 22.1 16.3 31.7 2.9 31.7 31.7 31.0 25.3 19.5 13.8

Total

Capacity

(MBh)

Total

1

Input

2

(kW)

251933-YTG-X-0615

Sensible Capacity (MBh)

Return Dry Bulb (°F) Return Dry Bulb (°F)

90 85 80 75 70 65 90 85 80 75 70 65

75°F 85°F

95°F 105°F

Temperature of Air on Condenser Coil

Total

Capacity

(MBh)

Total

1

Input

(kW)

Sensible Capacity (MBh)

2

Johnson Controls Unitary Products 25

251933-YTG-X-0615

ZE036 (3.0 Ton) (Continued)

Air on

Evaporator Coil

CFM

750

900

1050

1200

1350

1500

WB
(°F)

77 31.5 3.3 9.2 8.2 5.2 - - - 27.0 3.7 5.7 4.1 1.9 - - ­72 29.1 3.3 17.2 14.2 11.2 8.2 - - 25.2 3.6 14.6 11.6 8.7 5.7 - ­67 26.7 3.2 25.2 20.2 17.2 14.2 11.2 - 23.4 3.6 23.4 18.4 15.5 12.6 9.6 ­62 24.7 3.3 24.7 24.7 19.6 16.6 13.6 10.6 21.8 3.6 21.8 21.8 16.8 13.9 10.9 8.0
77 32.6 3.3 13.0 9.4 5.8 - - - 27.9 3.7 10.1 5.9 2.3 - - ­72 30.1 3.2 19.8 16.2 12.7 9.1 - - 26.1 3.6 17.2 13.6 10.0 6.5 - ­67 27.7 3.2 26.6 23.1 19.5 15.9 12.3 - 24.2 3.6 24.2 21.4 17.8 14.2 10.7 ­62 25.6 3.2 25.6 25.6 22.2 18.6 15.0 11.4 22.5 3.6 22.5 22.5 19.3 15.8 12.2 8.6
57 25.9 3.2 25.9 25.7 22.1 18.5 14.9 11.3 22.7 3.6 22.7 22.6 19.1 15.5 11.9 8.4
77 33.7 3.3 16.8 10.7 6.5 - - - 28.8 3.6 14.5 7.6 2.7 - - ­72 31.1 3.2 22.5 18.3 14.1 9.9 - - 26.9 3.6 19.8 15.6 11.4 7.2 - ­67 28.6 3.2 28.1 25.9 21.7 17.5 13.4 - 25.0 3.6 25.0 24.3 20.1 15.9 11.7 ­62 26.4 3.2 26.4 26.4 24.7 20.6 16.4 12.2 23.3 3.6 23.3 23.3 21.8 17.7 13.5 9.3
57 26.8 3.2 26.8 26.7 24.6 20.4 16.3 12.1 23.4 3.6 23.4 23.4 21.6 17.4 13.2 9.0
77 34.8 3.3 20.6 11.9 7.2 - - - 29.8 3.6 18.9 9.3 3.1 - - ­72 32.2 3.2 25.1 20.3 15.6 10.8 - - 27.8 3.6 22.4 17.6 12.7 7.9 - ­67 29.5 3.2 29.5 28.7 23.9 19.2 14.4 - 25.8 3.5 25.8 25.8 22.4 17.6 12.7 ­62 27.3 3.2 27.3 27.3 27.3 22.5 17.8 13.0 24.0 3.6 24.0 24.0 24.0 19.6 14.7 9.9
57 27.7 3.2 27.7 27.7 27.1 22.4 17.6 12.9 24.2 3.5 24.2 24.2 24.1 19.2 14.4 9.6
72 32.5 3.3 26.9 21.7 16.5 11.3 - - 28.3 3.6 24.5 19.3 14.1 8.8 - ­67 29.9 3.2 29.9 29.5 25.4 20.1 14.9 - 26.3 3.6 26.3 26.3 24.4 19.2 14.0 ­62 27.6 3.2 27.6 27.6 27.6 22.4 17.2 11.9 24.4 3.6 24.4 24.4 24.4 19.5 14.3 9.1
57 28.0 3.2 28.0 28.0 27.7 22.5 17.3 12.0 24.6 3.6 24.6 24.6 24.6 19.6 14.4 9.1
72 32.9 3.3 28.8 23.1 17.4 11.7 - - 28.7 3.6 26.7 21.0 15.4 9.7 - ­67 30.2 3.3 30.2 30.2 26.8 21.1 15.4 - 26.7 3.6 26.7 26.7 26.5 20.8 15.2 ­62 28.0 3.3 28.0 28.0 28.0 22.3 16.6 10.9 24.8 3.6 24.8 24.8 24.8 19.5 13.9 8.2
57 28.3 3.3 28.3 28.3 28.3 22.6 16.9 11.2 25.0 3.6 25.0 25.0 25.0 20.0 14.3 8.7

Total

Capacity

(MBh)

Total

1

Input

2

(kW)

Sensible Capacity (MBh)

Return Dry Bulb (°F) Return Dry Bulb (°F)

90 85 80 75 70 65 90 85 80 75 70 65

115°F 125°F

1. These capacities are gross ratings. For net capacity, deduct air blower motor, MBh = 3.415 x kW. Refer to the appropriate Blower
Performance Table for the kW of the supply air blower motor.

2. These ratings include the condenser fan motors (total 1 kW) and the compressor motors but not the supply air blower motor.

Temperature of Air on Condenser Coil

Total

Capacity

(MBh)

Total

1

Input
(kW)

Sensible Capacity (MBh)

2

26 Johnson Controls Unitary Products

ZE048 (4.0 Ton)

Air on

Evaporator Coil

CFM

1000

1200

1400

1600

1800

2000

1000

1200

1400

1600

1800

2000

WB
(°F)

77 60.0 2.6 27.4 22.9 18.4 - - - 58.1 3.1 26.4 22.0 17.5 - - ­72 56.4 2.5 34.3 29.8 25.3 20.8 - - 54.1 3.0 33.1 28.6 24.2 19.7 - ­67 52.8 2.4 41.1 36.6 32.1 27.6 23.1 - 50.1 2.9 39.7 35.3 30.8 26.4 22.0 ­62 48.4 2.4 48.4 43.6 38.7 34.2 29.7 25.2 45.8 2.9 45.8 43.4 37.4 33.0 28.6 24.1
77 62.1 2.7 30.0 25.0 20.0 - - - 59.8 3.1 29.0 24.0 19.0 - - ­72 58.3 2.6 37.4 32.4 27.4 22.3 - - 55.7 3.0 36.2 31.2 26.2 21.1 - ­67 54.6 2.5 44.8 39.8 34.8 29.7 24.7 - 51.6 3.0 43.4 38.4 33.4 28.3 23.3 ­62 50.1 2.5 50.1 46.9 41.9 36.9 31.9 26.8 47.1 2.9 47.1 45.5 40.5 35.5 30.4 25.4
57 47.7 2.4 47.7 47.7 44.8 39.8 34.8 29.7 46.1 2.9 46.1 46.1 42.4 37.3 32.3 27.3
77 64.2 2.7 32.6 27.0 21.5 - - - 61.6 3.2 31.6 26.0 20.4 - - ­72 60.3 2.6 40.5 35.0 29.5 23.9 - - 57.3 3.1 39.4 33.8 28.1 22.5 - ­67 56.5 2.6 48.5 43.0 37.4 31.9 26.3 - 53.1 3.0 47.1 41.5 35.9 30.3 24.6 ­62 51.7 2.5 51.7 50.2 45.1 39.5 34.0 28.5 48.5 3.0 48.5 47.7 43.6 37.9 32.3 26.7
57 49.3 2.4 49.3 49.3 48.2 42.7 37.1 31.6 47.4 2.9 47.4 47.4 45.6 40.0 34.3 28.7
77 66.3 2.8 35.1 29.1 23.0 - - - 63.3 3.2 34.3 28.0 21.8 - - ­72 62.3 2.7 43.7 37.6 31.5 25.5 - - 58.9 3.1 42.6 36.3 30.1 23.9 - ­67 58.3 2.6 52.2 46.1 40.1 34.0 28.0 - 54.5 3.1 50.8 44.6 38.4 32.2 26.0 ­62 53.4 2.6 53.4 53.4 48.3 42.2 36.2 30.1 49.9 3.0 49.9 49.9 46.6 40.4 34.2 28.0
57 50.9 2.5 50.9 50.9 50.9 45.6 39.5 33.4 48.8 3.0 48.8 48.8 48.8 42.6 36.3 30.1
72 63.7 2.7 46.3 39.8 33.2 26.6 - - 60.0 3.2 45.7 38.9 32.1 25.2 - ­67 59.6 2.6 56.6 48.7 42.1 35.5 29.0 - 55.5 3.1 53.6 47.7 40.9 34.1 27.2 ­62 54.7 2.6 54.7 54.7 52.1 45.5 38.9 32.3 50.7 3.0 50.7 50.7 49.1 42.3 35.4 28.6
57 52.1 2.5 52.1 52.1 52.1 45.9 39.3 32.7 49.6 3.0 49.6 49.6 49.6 42.8 36.0 29.1
72 65.2 2.7 49.0 41.9 34.8 27.7 - - 61.0 3.2 48.9 41.5 34.0 26.6 - ­67 61.0 2.6 61.0 51.3 44.2 37.1 30.0 - 56.4 3.1 56.4 50.8 43.4 36.0 28.5 ­62 55.9 2.6 55.9 55.9 55.9 48.8 41.7 34.5 51.6 3.1 51.6 51.6 51.6 44.2 36.7 29.3
57 53.3 2.5 53.3 53.3 53.3 46.1 39.0 31.9 50.5 3.0 50.5 50.5 50.5 43.0 35.6 28.1

77 56.3 3.6 25.4 21.0 16.6 - - - 52.0 4.1 21.4 18.5 14.2 - - ­72 51.8 3.5 31.9 27.5 23.1 18.7 - - 47.3 4.0 29.3 25.0 20.7 16.4 - ­67 47.3 3.4 38.3 34.0 29.6 25.2 20.8 - 42.7 3.9 37.1 31.5 27.2 22.9 18.6 ­62 43.2 3.4 43.2 43.1 36.2 31.8 27.4 23.1 39.2 3.9 39.2 39.2 32.4 28.1 23.8 19.5
77 57.6 3.6 28.1 23.0 18.0 - - - 53.3 4.2 25.6 20.5 15.5 - - ­72 53.1 3.5 35.1 30.0 25.0 19.9 - - 48.6 4.1 32.7 27.7 22.6 17.6 - ­67 48.5 3.4 42.1 37.0 32.0 26.9 21.9 - 43.8 4.0 39.9 34.8 29.8 24.8 19.7 ­62 44.2 3.4 44.2 44.2 39.1 34.1 29.0 24.0 40.2 3.9 40.2 40.2 35.5 30.4 25.4 20.4
57 44.6 3.4 44.6 44.6 40.0 34.9 29.9 24.8 41.0 3.9 41.0 40.8 36.0 31.0 26.0 21.0
77 59.0 3.6 30.7 25.0 19.3 - - - 54.7 4.2 29.7 22.6 16.8 - - ­72 54.3 3.5 38.2 32.5 26.8 21.1 - - 49.8 4.1 36.2 30.4 24.6 18.8 - ­67 49.6 3.5 45.8 40.1 34.3 28.6 22.9 - 45.0 4.0 42.6 38.2 32.4 26.6 20.9 ­62 45.3 3.4 45.3 45.2 42.0 36.3 30.6 24.9 41.3 4.0 41.3 41.3 38.5 32.8 27.0 21.2
57 45.6 3.4 45.6 45.6 43.0 37.2 31.5 25.8 42.1 3.9 42.1 42.0 39.2 33.4 27.6 21.9
77 60.4 3.6 33.4 27.0 20.6 - - - 56.0 4.2 33.8 24.7 18.2 - - ­72 55.6 3.6 41.4 35.1 28.7 22.3 - - 51.1 4.1 39.6 33.1 26.6 20.1 - ­67 50.8 3.5 49.5 43.1 36.7 30.3 24.0 - 46.1 4.0 45.4 41.5 35.0 28.5 22.0 ­62 46.3 3.4 46.3 46.3 45.0 38.6 32.2 25.8 42.3 4.0 42.3 42.3 41.6 35.1 28.6 22.1
57 46.7 3.4 46.7 46.7 45.9 39.6 33.2 26.8 43.1 4.0 43.1 43.1 42.3 35.8 29.3 22.8
72 56.2 3.6 45.1 38.1 31.0 23.9 - - 51.9 4.1 43.0 35.9 28.7 21.5 - ­67 51.3 3.5 50.7 46.7 39.7 32.6 25.5 - 46.8 4.0 46.5 44.1 37.8 30.6 23.5 ­62 46.8 3.5 46.8 46.8 46.1 39.1 32.0 24.9 42.9 4.0 42.9 42.9 42.6 35.4 28.3 21.1
57 47.2 3.5 47.2 47.2 46.8 39.7 32.7 25.6 43.8 4.0 43.8 43.8 43.4 36.2 29.1 21.9
72 56.8 3.6 48.8 41.1 33.3 25.5 - - 52.6 4.2 46.5 38.7 30.8 23.0 - ­67 51.9 3.5 51.9 50.4 42.6 34.8 27.1 - 47.5 4.1 47.5 46.8 40.6 32.8 25.0 ­62 47.3 3.5 47.3 47.3 47.3 39.5 31.8 24.0 43.6 4.0 43.6 43.6 43.6 35.8 28.0 20.2
57 47.7 3.5 47.7 47.7 47.7 39.9 32.1 24.4 44.5 4.0 44.5 44.5 44.5 36.7 28.8 21.0

Total

Capacity

(MBh)

251933-YTG-X-0615

Total

1

Input

2

(kW)

Sensible Capacity (MBh)

Return Dry Bulb (°F) Return Dry Bulb (°F)

90 85 80 75 70 65 90 85 80 75 70 65

75°F 85°F

95°F 105°F

Temperature of Air on Condenser Coil

Total

Capacity

(MBh)

Total

1

Input
(kW)

Sensible Capacity (MBh)

2

Johnson Controls Unitary Products 27

251933-YTG-X-0615

ZE048 (4.0 Ton) (Continued)

Air on

Evaporator Coil

CFM

1000

1200

1400

1600

1800

2000

WB
(°F)

77 47.6 4.7 17.5 15.9 11.7 - - - 43.3 5.3 14.6 12.5 9.3 - - ­72 42.9 4.6 26.6 22.5 18.3 14.1 - - 38.4 5.2 24.0 19.9 15.9 11.8 - ­67 38.1 4.5 35.8 29.0 24.8 20.6 16.5 - 33.5 5.0 33.5 26.5 22.5 18.4 14.3 ­62 35.3 4.4 35.3 35.3 28.6 24.4 20.2 16.0 31.3 5.0 31.3 31.3 24.7 20.7 16.6 12.5
77 49.0 4.7 23.0 18.0 13.0 - - - 44.7 5.3 21.4 15.6 10.6 - - ­72 44.1 4.6 30.3 25.3 20.3 15.3 - - 39.6 5.2 28.0 23.0 18.0 13.0 - ­67 39.2 4.5 37.6 32.6 27.6 22.6 17.6 - 34.6 5.1 34.6 30.5 25.5 20.5 15.5 ­62 36.3 4.5 36.3 36.3 31.8 26.8 21.8 16.8 32.3 5.0 32.3 32.3 28.1 23.2 18.2 13.2
57 37.5 4.4 37.5 37.1 32.1 27.1 22.1 17.1 34.0 4.9 34.0 33.4 28.2 23.2 18.2 13.2
77 50.3 4.8 28.6 20.2 14.4 - - - 46.0 5.4 28.3 18.6 11.9 - - ­72 45.3 4.7 34.1 28.2 22.4 16.6 - - 40.8 5.2 32.0 26.1 20.2 14.3 - ­67 40.3 4.6 39.5 36.3 30.5 24.6 18.8 - 35.6 5.1 35.6 34.4 28.5 22.6 16.8 ­62 37.3 4.5 37.3 37.3 35.0 29.2 23.4 17.6 33.3 5.0 33.3 33.3 31.5 25.7 19.8 13.9
57 38.6 4.4 38.6 38.3 35.4 29.5 23.7 17.9 35.0 5.0 35.0 34.7 31.6 25.7 19.8 14.0
77 51.7 4.8 34.1 22.3 15.7 - - - 47.4 5.4 35.2 21.6 13.2 - - ­72 46.5 4.7 37.8 31.1 24.5 17.8 - - 42.0 5.3 35.9 29.1 22.4 15.6 - ­67 41.4 4.6 41.4 39.9 33.3 26.6 20.0 - 36.7 5.1 36.7 36.7 31.5 24.8 18.0 ­62 38.3 4.5 38.3 38.3 38.3 31.6 25.0 18.4 34.3 5.1 34.3 34.3 34.3 28.2 21.4 14.6
57 39.6 4.5 39.6 39.6 38.6 32.0 25.4 18.7 36.0 5.0 36.0 36.0 35.0 28.2 21.5 14.7
72 47.5 4.7 40.9 33.7 26.4 19.2 - - 43.2 5.3 38.8 31.5 24.2 16.8 - ­67 42.2 4.6 42.2 41.5 35.9 28.7 21.4 - 37.7 5.1 37.7 37.7 34.1 26.7 19.4 ­62 39.1 4.5 39.1 39.1 39.1 31.8 24.6 17.3 35.2 5.1 35.2 35.2 35.2 28.2 20.9 13.6
57 40.4 4.5 40.4 40.4 39.9 32.7 25.5 18.2 37.0 5.0 37.0 37.0 36.5 29.2 21.9 14.5
72 48.5 4.7 44.1 36.3 28.4 20.5 - - 44.4 5.2 41.8 33.9 26.0 18.1 - ­67 43.1 4.6 43.1 43.1 38.6 30.7 22.9 - 38.7 5.1 38.7 38.7 36.6 28.7 20.8 ­62 39.9 4.5 39.9 39.9 39.9 32.0 24.2 16.3 36.2 5.1 36.2 36.2 36.2 28.3 20.4 12.5
57 41.3 4.5 41.3 41.3 41.3 33.4 25.5 17.7 38.0 5.0 38.0 38.0 38.0 30.1 22.2 14.4

Total

Capacity

(MBh)

Total

1

Input

2

(kW)

Sensible Capacity (MBh)

Return Dry Bulb (°F) Return Dry Bulb (°F)

90 85 80 75 70 65 90 85 80 75 70 65

115°F 125°F

1. These capacities are gross ratings. For net capacity, deduct air blower motor, MBh = 3.415 x kW. Refer to the appropriate Blower
Performance Table for the kW of the supply air blower motor.

2. These ratings include the condenser fan motors (total 1 kW) and the compressor motors but not the supply air blower motor.

Temperature of Air on Condenser Coil

Total

Capacity

(MBh)

Total

1

Input
(kW)

Sensible Capacity (MBh)

2

28 Johnson Controls Unitary Products

ZE060 (5.0 Ton)

Air on

Evaporator Coil

CFM

1250

1500

1750

2000

2250

2500

1250

1500

1750

2000

2250

2500

WB
(°F)

77 74.6 3.2 34.0 28.7 23.4 - - - 70.6 3.8 31.6 26.4 21.1 - - ­72 69.2 3.2 42.2 36.9 31.6 26.3 - - 65.3 3.7 39.7 34.4 29.2 23.9 - ­67 63.8 3.2 50.4 45.1 39.8 34.5 29.2 - 60.1 3.7 47.7 42.5 37.2 32.0 26.7 ­62 58.4 3.1 58.4 56.3 48.8 43.5 38.2 32.9 55.1 3.7 55.1 53.7 45.6 40.4 35.1 29.9
77 76.5 3.3 37.3 31.2 25.1 - - - 72.4 3.8 35.0 29.0 23.0 - - ­72 71.0 3.2 46.1 40.0 33.9 27.9 - - 67.1 3.7 43.8 37.7 31.7 25.7 - ­67 65.4 3.2 54.9 48.8 42.8 36.7 30.6 - 61.7 3.7 52.5 46.5 40.5 34.5 28.5 ­62 59.9 3.2 59.9 58.5 52.4 46.4 40.3 34.2 56.6 3.7 56.6 55.6 49.6 43.6 37.6 31.6
57 59.0 3.1 59.0 59.0 54.1 48.0 41.9 35.9 56.2 3.7 56.2 56.2 50.6 44.5 38.5 32.5
77 78.4 3.3 40.6 33.7 26.9 - - - 74.3 3.8 38.4 31.6 24.9 - - ­72 72.7 3.3 50.0 43.1 36.3 29.5 - - 68.8 3.8 47.8 41.1 34.3 27.5 - ­67 67.1 3.2 59.4 52.5 45.7 38.9 32.1 - 63.3 3.7 57.3 50.5 43.8 37.0 30.2 ­62 61.4 3.2 61.4 60.7 56.1 49.2 42.4 35.6 58.1 3.7 58.1 57.6 53.6 46.9 40.1 33.3
57 60.5 3.2 60.5 60.5 57.8 51.0 44.2 37.4 57.7 3.7 57.7 57.7 54.6 47.9 41.1 34.3
77 80.3 3.3 43.8 36.3 28.7 - - - 76.1 3.8 41.8 34.2 26.7 - - ­72 74.5 3.3 53.9 46.3 38.7 31.1 - - 70.5 3.8 51.9 44.4 36.9 29.4 - ­67 68.7 3.2 63.9 56.3 48.7 41.1 33.6 - 64.9 3.8 62.1 54.6 47.0 39.5 32.0 ­62 62.8 3.2 62.8 62.8 59.7 52.1 44.6 37.0 59.5 3.7 59.5 59.5 57.7 50.1 42.6 35.1
57 62.0 3.2 62.0 62.0 61.6 54.0 46.5 38.9 59.1 3.7 59.1 59.1 58.7 51.2 43.7 36.2
72 81.4 2.6 59.5 51.3 43.0 34.7 - - 71.7 3.8 55.7 47.5 39.3 31.1 - ­67 75.0 2.6 72.6 63.7 54.1 45.8 37.5 - 66.0 3.8 64.6 58.3 50.1 42.0 33.8 ­62 68.6 2.5 68.6 68.6 67.1 58.8 50.5 42.2 60.5 3.7 60.5 60.5 59.6 51.4 43.3 35.1
57 67.8 2.5 67.8 67.8 67.6 59.3 51.0 42.7 60.1 3.7 60.1 60.1 59.9 51.8 43.6 35.4
72 88.2 1.9 65.2 56.2 47.2 38.2 - - 73.0 3.8 59.4 50.6 41.7 32.9 - ­67 81.3 1.9 81.3 71.2 59.6 50.5 41.5 - 67.1 3.8 67.1 62.1 53.2 44.4 35.6 ­62 74.4 1.9 74.4 74.4 74.4 65.4 56.4 47.4 61.6 3.7 61.6 61.6 61.6 52.7 43.9 35.1
57 73.6 1.9 73.6 73.6 73.6 64.5 55.5 46.5 61.1 3.7 61.1 61.1 61.1 52.3 43.5 34.7

77 66.5 4.3 29.3 24.1 18.9 - - - 61.4 4.9 24.0 19.8 14.7 - - ­72 61.5 4.2 37.1 32.0 26.8 21.6 - - 56.9 4.9 34.1 29.0 23.9 18.7 - ­67 56.4 4.2 45.0 39.8 34.6 29.4 24.2 - 52.5 4.9 44.2 38.1 33.0 27.9 22.8 ­62 51.9 4.2 51.9 51.1 42.4 37.3 32.1 26.9 48.7 4.8 48.7 48.3 39.8 34.7 29.6 24.4
77 68.3 4.3 32.7 26.8 20.8 - - - 62.8 5.0 27.9 22.1 16.2 - - ­72 63.2 4.3 41.4 35.5 29.5 23.6 - - 58.3 4.9 38.0 32.2 26.3 20.4 - ­67 58.0 4.2 50.1 44.2 38.2 32.3 26.3 - 53.7 4.9 48.1 42.2 36.4 30.5 24.6 ­62 53.3 4.2 53.3 52.8 46.8 40.9 34.9 29.0 49.9 4.8 49.9 49.6 43.8 38.0 32.1 26.2
57 53.4 4.2 53.4 53.0 47.1 41.1 35.1 29.2 50.2 4.8 50.2 50.0 44.1 38.3 32.4 26.5
77 70.2 4.3 36.2 29.5 22.8 - - - 64.3 5.0 31.9 24.3 17.7 - - ­72 64.9 4.3 45.7 39.0 32.3 25.6 - - 59.7 5.0 42.0 35.3 28.7 22.1 - ­67 59.5 4.3 55.2 48.5 41.8 35.1 28.4 - 55.0 4.9 52.0 46.3 39.7 33.1 26.4 ­62 54.8 4.2 54.8 54.5 51.2 44.5 37.8 31.1 51.0 4.9 51.0 50.9 47.9 41.2 34.6 28.0
57 54.8 4.2 54.8 54.6 51.5 44.7 38.0 31.3 51.4 4.9 51.4 51.3 48.2 41.6 34.9 28.3
77 72.0 4.3 39.7 32.2 24.7 - - - 65.8 5.0 35.9 26.6 19.2 - - ­72 66.5 4.3 50.0 42.5 35.1 27.6 - - 61.0 5.0 45.9 38.5 31.1 23.7 - ­67 61.1 4.3 60.3 52.9 45.4 37.9 30.4 - 56.3 5.0 55.9 50.4 43.0 35.6 28.3 ­62 56.2 4.2 56.2 56.2 55.6 48.2 40.7 33.2 52.2 4.9 52.2 52.2 51.9 44.5 37.1 29.7
57 56.2 4.2 56.2 56.2 55.9 48.4 40.9 33.4 52.6 4.9 52.6 52.6 52.3 44.9 37.5 30.1
72 62.1 5.0 51.8 43.7 35.7 27.6 - - 59.2 5.3 48.5 40.5 32.4 24.4 - ­67 57.0 4.9 56.6 52.9 46.2 38.1 30.0 - 54.6 5.3 54.4 51.7 45.0 37.0 29.0 ­62 52.5 4.9 52.5 52.5 52.2 44.1 36.1 28.0 50.7 5.2 50.7 50.7 50.5 42.5 34.5 26.5
57 52.5 4.9 52.5 52.5 52.3 44.2 36.2 28.1 51.1 5.2 51.1 51.1 50.9 42.9 34.9 26.9
72 57.7 5.6 53.5 44.9 36.3 27.6 - - 57.4 5.6 51.1 42.4 33.8 25.1 - ­67 53.0 5.6 53.0 53.0 46.9 38.3 29.6 - 53.0 5.6 53.0 53.0 46.9 38.3 29.6 ­62 48.7 5.5 48.7 48.7 48.7 40.1 31.4 22.8 49.2 5.5 49.2 49.2 49.2 40.5 31.9 23.2
57 48.7 5.5 48.7 48.7 48.7 40.1 31.5 22.8 49.6 5.5 49.6 49.6 49.6 40.9 32.3 23.7

Total

Capacity

(MBh)

251933-YTG-X-0615

Total

1

Input

2

(kW)

Sensible Capacity (MBh)

Return Dry Bulb (°F) Return Dry Bulb (°F)

90 85 80 75 70 65 90 85 80 75 70 65

75°F 85°F

95°F 105°F

Temperature of Air on Condenser Coil

Total

1

Capacity

(MBh)

(kW)

Total
Input

Sensible Capacity (MBh)

2

Johnson Controls Unitary Products 29

251933-YTG-X-0615

ZE060 (5.0 Ton) (Continued)

Air on

Evaporator Coil

CFM

1250

1500

1750

2000

2250

2500

WB
(°F)

77 56.2 5.6 18.7 15.6 10.5 - - - 51.0 6.2 13.2 11.3 6.3 - - ­72 52.4 5.6 31.1 26.0 20.9 15.9 - - 47.8 6.3 28.0 23.0 18.0 13.0 - ­67 48.5 5.6 43.4 36.5 31.4 26.3 21.3 - 44.6 6.3 42.7 34.8 29.8 24.8 19.8 ­62 45.5 5.5 45.5 45.5 37.2 32.1 27.1 22.0 42.2 6.1 42.2 42.2 34.6 29.6 24.6 19.6
77 57.3 5.6 23.1 17.3 11.5 - - - 51.8 6.3 18.3 12.6 6.9 - - ­72 53.4 5.6 34.6 28.8 23.0 17.2 - - 48.5 6.3 31.2 25.5 19.8 14.0 - ­67 49.5 5.6 46.1 40.3 34.5 28.7 22.9 - 45.2 6.3 44.1 38.4 32.6 26.9 21.2 ­62 46.4 5.5 46.4 46.4 40.9 35.0 29.2 23.4 42.9 6.2 42.9 42.9 37.9 32.1 26.4 20.7
57 47.1 5.5 47.1 47.0 41.2 35.4 29.6 23.8 44.0 6.2 44.0 44.0 38.3 32.6 26.9 21.1
77 58.4 5.6 27.6 19.1 12.6 - - - 52.6 6.3 23.5 13.9 7.4 - - ­72 54.4 5.6 38.2 31.6 25.1 18.5 - - 49.2 6.3 34.4 27.9 21.5 15.0 - ­67 50.5 5.6 48.8 44.1 37.6 31.0 24.5 - 45.9 6.3 45.5 41.9 35.5 29.0 22.5 ­62 47.3 5.5 47.3 47.3 44.5 38.0 31.4 24.9 43.5 6.2 43.5 43.5 41.2 34.7 28.2 21.8
57 48.1 5.5 48.1 48.0 44.9 38.4 31.8 25.3 44.7 6.2 44.7 44.7 41.7 35.2 28.7 22.3
77 59.6 5.7 32.0 20.9 13.6 - - - 53.3 6.3 28.6 15.2 8.0 - - ­72 55.5 5.7 41.7 34.4 27.1 19.8 - - 50.0 6.3 37.6 30.4 23.2 16.0 - ­67 51.4 5.7 51.4 48.0 40.7 33.4 26.1 - 46.6 6.3 46.6 45.5 38.3 31.1 23.9 ­62 48.2 5.5 48.2 48.2 48.2 40.9 33.6 26.3 44.2 6.2 44.2 44.2 44.2 37.3 30.1 22.8
57 49.0 5.6 49.0 49.0 48.6 41.3 34.0 26.7 45.4 6.3 45.4 45.4 45.0 37.8 30.6 23.4
72 56.3 5.6 45.2 37.2 29.2 21.3 - - 53.4 6.0 41.8 33.9 26.0 18.1 - ­67 52.2 5.6 52.2 50.5 43.8 35.8 27.9 - 49.8 6.0 49.8 49.2 42.6 34.7 26.8 ­62 48.9 5.5 48.9 48.9 48.9 40.9 33.0 25.0 47.1 5.9 47.1 47.1 47.1 39.3 31.4 23.5
57 49.7 5.6 49.7 49.7 49.5 41.6 33.6 25.6 48.3 5.9 48.3 48.3 48.1 40.2 32.3 24.4
72 57.1 5.6 48.6 39.9 31.3 22.7 - - 56.9 5.6 46.1 37.5 28.8 20.2 - ­67 53.0 5.6 53.0 53.0 46.9 38.3 29.6 - 53.0 5.6 53.0 53.0 46.9 38.3 29.6 ­62 49.6 5.5 49.6 49.6 49.6 41.0 32.3 23.7 50.1 5.5 50.1 50.1 50.1 41.4 32.8 24.1
57 50.4 5.5 50.4 50.4 50.4 41.8 33.2 24.5 51.3 5.5 51.3 51.3 51.3 42.6 34.0 25.4

Total

Capacity

(MBh)

Total

1

Input

2

(kW)

Sensible Capacity (MBh)

Return Dry Bulb (°F) Return Dry Bulb (°F)

90 85 80 75 70 65 90 85 80 75 70 65

115°F 125°F

1. These capacities are gross ratings. For net capacity, deduct air blower motor, MBh = 3.415 x kW. Refer to the appropriate Blower
Performance Table for the kW of the supply air blower motor.

2. These ratings include the condenser fan motors (total 1 kW) and the compressor motors but not the supply air blower motor.

Temperature of Air on Condenser Coil

Total

1

Capacity

(MBh)

(kW)

Total
Input

Sensible Capacity (MBh)

2

30 Johnson Controls Unitary Products