A
V
A
w
TECHNICAL GUIDE
SPLIT-SYSTEM
IR CONDITIONERS
14.5 SEER – R-410A
MODELS:
TCGF24 THRU 60
(2 THRU 5 NOMINAL TONS, 1 PHASE)
LISTED
Due to continuous product improvement, specifications
are subject to change without notice.
isit us on the web at www.york.com
dditional rating information can be found at
ww.ahridirectory.org
ISO 9001
Certified Quality
Management System
413432-YTG-A-0608
DESCRIPTION
The 14.5 SEER Series condensing unit is the outdoor part of
a versatile system of air conditioning. It is designed to be custom-matched with one of UPG’s complete line of evaporator
sections, with each serving a specific function. Matching Air
Handlers are available for upflow, downflow, or horizontal
applications to provide a complete system. Electric Heaters
are available, if required. Add-on coils are available for use
with upflow, downflow, or horizontal furnaces and air handlers.
WARRANTY
Single Phase Units:
5-year limited parts warranty.
10-year limited compressor warranty.
FEATURES
• QUALITY CONDENSER COILS - The coil is constructed
of aluminum microchannel tubing and enhanced aluminum
fins for increased efficiency and corrosion protection.
• PROTECTED COMPRESSOR - The compressor is internally protected against high pressure and temperature and
externally by a factory installed high pressure switch. This
protects the compressor if undesirable operating conditions occur. A liquid line filter-drier further protects the
compressor.
• DURABLE FINISH - The cabinet is made of pre-painted
steel. The pre-treated galvanized steel provides a better
paint to steel bond, which resists corrosion and rust creep.
Special primer formulas and matted-textured finish insure
less fading when exposed to sunlight.
• LOWER INSTALLED COST - Installation time and costs
are reduced by easy power and control wiring connections. Available in sweat connect models only. The unit
contains enough refrigerant for matching indoor coils and
15 feet of interconnecting piping. The small base dimension means less space is required on the ground or roof.
• TOP DISCHARGE - The warm air from the top mounted
fan is blown up away from the structure and any landscaping. This allows compact location on multi-unit applications.
• LOW OPERATING SOUND LEVEL - The upward air flow
carries the normal operating noise away from the living
area. The rigid top panel effectively isolates any motor
sound. Isolated compressor mounts minimize compressor
operating sounds.
• LOW MAINTENANCE - Long life permanently lubricated
motor-bearings need no annual servicing.
• EASY SERVICE ACCESS - Fully exposed refrigerant connections, and a single panel covering the electrical controls make for easy servicing of the unit.
• SECURED SERVICE VALVES - Secured re-usable ser-
vice valves are provided on both the liquid and vapor
sweat connections for ease of evacuating and charging.
• U.L. and C.U.L. listed - approved for outdoor application.
Certified in accordance with the Unitary Small Equipment certification program, which is based on ARI Standard 210/240.
FOR DISTRIBUTION USE ONLY - NOT TO BE USED AT POINT OF RETAIL SALE
413432-YTG-A-0608
Physical and Electrical Data
MODEL TCGF24S41S1 TCGF30S41S1 TCGF36S41S1 TCGF42S41S1 TCGF48S41S1 TCGF60S41S1
Unit Supply Voltage 208-230V, 1φ, 60Hz
Normal Voltage Range
1
Minimum Circuit Ampacity 16.8 18.4 19.09 23.9 27.9 35.9
Max. Overcurrent Device Amps
Min. Overcurrent Device Amps
2
3
25 30 30 40 45 60
20 20 20 25 30 40
Compressor Type Scroll Scroll Scroll Scroll Scroll Scroll
Compressor
Amps
Rated Load 12.8 14.1 14.1 17.9 21.1 27.5
Locked Rotor 58 73 77 112 115 135
Crankcase Heater No No No No No No
Fan Motor Amps Rated Load .8 .8 1.5 1.5 1.5 1.5
Fan Diameter Inches 22 22 22 24 24 24
Rated HP 1/8 1/8 1/4 1/4 1/4 1/4
Fan Motor
Nominal RPM 1075 1075 850 850 850 850
Nominal CFM 2750 2800 3200 3600 3600 3700
Face Area Sq. Ft. 13.07 17.44 17.44 20.03 21.37 24.04
Coil
Rows Deep 1 1 1 1 1 1
Fin / Inches 23 23 23 23 23 23
Liquid Line Set OD (Field Installed) 3/8 3/8 3/8 3/8 3/8 3/8
Vapor Line Set OD (Field Installed) 3/4 3/4 3/4 7/8 7/8 1 1/8
Unit Charge (Lbs. - Oz.)
4
3 - 2 3 - 3 - 10 4 - 4 4 - 9 5 - 9
Charge Per Foot, Oz. 0.62 0.62 0.62 0.67 0.67 0.75
Operating Weight Lbs. TBD 130 145 172 180 199
1. Rated in accordance with ARI Standard 110, utilization range “A”.
2. Dual element fuses or HACR circuit breaker. Maximum allowable overcurrent protection.
3. Dual element fuses or HACR circuit breaker. Minimum recommended overcurrent protection.
4. The Unit Charge is correct for the outdoor unit, matched indoor coil and 15 feet of refrigerant tubing. For tubing lengths other than
15 feet, add or subtract the amount of refrigerant, using the difference in length multiplied by the per foot value.
187 to 252
All dimensions are in inches. They are subject to change
without notice. Certified dimensions will be provided upon
C
A
B
request.
Unit
Model
24 28 29 29
36 36 29 29
42 34 33.6 33.6
48 36 33.6 33.6
60 40 33.6 33.6
1. Including Fan Guard.
2. Adapter fitting required for 1-1/8” line set.
Dimensions
(Inches)
1
A
B C Liquid Vapor
Refrigerant Connection
Service Valve Size
3/4”30 36 29 29
3/8”
7/8”
2
7/8”
2 Johnson Controls Unitary Products
413432-YTG-A-0608
Additional R-410A Charge / Orifice Size for Various Matched Systems
Outdoor Unit TCGF24S41S1 TCGF30S41S1 TCGF36S41S1 TCGF42S41S1 TCGF48S41S1 TCGF60S41S1
Required Orifice or TXV
Factory Charge, lbs-oz 3 - 2 3 - 7 3 - 10 4 - 4 4 - 9 5 - 9
1
1TVM902 1TVM903 1TVM903 1TVM903 1TVM905 1TVM906
Indoor Coil
FC/MC/PC24A3X 5 – – – – –
FC/MC/PC24B3X 5 – – – – –
FC/MC/PC30A3X 12 2 – – – –
FC/MC/PC30B3X 12 2 – – – –
FC/MC/PC32A3X 16 10 – – – –
FC/MC/PC35B3X 16 10 8 – – –
FC/MC/PC35C3X 16 10 8 – – –
FC/MC/PC36A3X 8 4 1 – – –
FC/MC/PC36B3X 8 4 1 – – –
FC/MC/PC36C3X 8 4 1 – – –
FC/MC/PC37A3X 24 19 15 – – –
FC/MC/PC43B3X 24 19 15 5 – –
FC/MC/PC43C3X 24 19 15 5 – –
FC/MC/PC48C3X 40 32 15 17 16 –
FC/MC/PC48D3X 40 32 27 17 16 –
FC/MC/PC60D3X – – – 17 16 0
FC/MC62D3X – – – 25 26 18
UC24A3X 8 – – – – –
UC24B3X 8 – – – – –
UC30A3X 8 4 – – – –
UC30B3X 8 4 – – – –
UC36A3X – – – – – –
UC36B3X – – – – – –
UC36C3X – – – – – –
UC42B3X – – – – – –
UC42C3X – – – – – –
UC48C3X – – – – – –
UC48D3X – – – – – –
UC60C3X – – 12 – – –
UC60D3X – – 12 – – –
HC18A3X – – – – – –
HC30A3X 10 – – – – –
HC36B3X 16 11 8 – – –
HC42C3X 25 19 15 6 – –
HC60D3X – – – 0 0 0
HD24*3X 16 – – – – –
HD36*3X 18 – – – – –
HD48*3X 51 42 36 24 25 –
HD60*3X – – – – 24 –
AHP18B3X – – – – – –
AHP24B3X 3 – – – – –
AHP30B3X 16 – – – –
AHP36C3X – 19 15 – – –
AHP42C3X – – – – – –
AHP/SHP60D3X – – – – 1 –
AV24B3X 3 – – – – –
AV36C3X 25 19 15 – – –
AV/SV48D3X – – 9 0 1 –
AV/SV60D3X – – – 0 1 0
For notes see Page 4.
2,3,4
Additional Charge, Oz
Johnson Controls Unitary Products 3
413432-YTG-A-0608
Additional R-410A Charge / Orifice Size for Various Matched Systems (Continued)
Outdoor Unit TCGF24S41S1 TCGF30S41S1 TCGF36S41S1 TCGF42S41S1 TCGF48S41S1 TCGF60S41S1
Required Orifice or TXV
1
Factory Charge, lbs-oz 3 - 2 3 - 7 3 - 10 4 - 4 4 - 9 5 - 9
1TVM902 1TVM903 1TVM903 1TVM903 1TVM905 1TVM906
Indoor Coil
F4FP024
F4FP030
F4FP036
F4FP040
F4FP042
F4FP045
F5FP048
F5FP060
F4FV060
2,3,4
See Caution below
See Caution below
See Caution below
See Caution below
See Caution below
See Caution below
See Caution below
See Caution below
See Caution below
0 – – – – –
3 0 – – – –
– 8 5 – – –
– 12 8 – – –
– – 8 0 – –
– – 9 2 – –
– – 20 10 11 –
– – 20 10 11 –
– – 9 10 1 –
Additional Charge, Oz
FOOTNOTES:
1. Systems matched with furnace or air handlers not equipped with blower-off delays may require blower Time Delay Kit 2FD06700224.
2. PC coils cannot be used in downflow or horizontal applications. FC coils cannot be used in horizontal applications.
3. A TXV kit must be used with these coils to obtain system performance. Note: If a TXV is factory installed on the coil, it must be replaced
with the listed TXV
4. Refer to Technical Guide for actual system performance for specified matches.
PROCEDURES:
1. Unit factory charge listed on the unit nameplate includes refrigerant for the condenser, the smallest evaporator and 15 feet of interconnecting line tubing.
2. Verify the TXV or orifice and additional charge required for specific evaporator coil in the system using the above table.
3. Add additional charge for the amount of interconnecting line tubing greater than 15 feet at the rate specified in Physical and Electrical Data Table.
4. For TXV match charge weight needs to be weighed in for specififc coil match and lineset length.
5. Permanently mark the unit nameplate with the total system charge. Total System Charge = Base Charge (as shipped) + adder for
evaporator + adder for line set.
If the F*FP Air Handler used has a with a facto ry installed R-22 TXV it MUST BE CHANGED OUT to a R-410A TXV or a orifice for proper operation.
If the TXV is not changed out system d amage will occur.
4 Johnson Controls Unitary Products
413432-YTG-A-0608
COOLING CAPACITY - With Air Handler Coils
UNIT
MODEL
TCGF24S41S1
TCGF30S41S1
TCGF36S41S1
TCGF42S41S1
TCGF48S41S1
TCGF60S41S1 MA20D 24 FC/MC62D 1800 57.0 39.0 14.00 12.10
TCGF24S41S1
TCGF30S41S1
TCGF36S41S1
For notes see Page 6.
AIR HANDLER
MODEL W
MA08B 17 FC/MC24B 800 24.8 17.3 14.35 12.15
MA08B 17 FC/MC30B 800 24.8 17.3 14.35 12.15
MA08B 17 FC/MC35B 800 25.0 17.6 14.50 12.25
MA08B 17 FC/MC36B 800 25.0 17.6 14.40 12.25
MA08B 17 FC/MC43B 800 25.2 18.0 14.60 12.35
MA12B 17 FC/MC30B 1000 28.8 20.6 14.00 12.00
MA12B 17 FC/MC35B 1000 29.0 21.0 14.05 12.00
MA12B 17 FC/MC36B 1000 29.0 21.0 14.00 12.00
MA12B 17 FC/MC43B 1000 29.6 21.6 14.45 12.00
MA12B 17 FC/MC35B 1200 34.4 25.4 14.20 12.10
MA12B 17 FC/MC36B 1200 34.2 25.0 14.00 12.00
MA12B 17 FC/MC43B 1200 35.2 26.0 14.50 12.30
MA14D 24 FC/MC48D 1200 35.6 26.4 14.65 12.35
MA16C 21 FC/MC43C 1400 40.5 30.4 14.10 12.10
MA14D 24 FC/MC48D 1400 41.0 30.8 14.40 12.30
MA16C 21 FC/MC48C 1400 41.0 30.8 14.40 12.30
MA14D 24 FC/MC60D 1400 41.0 30.8 14.35 12.10
MA16C 21 FC/MC60C 1400 41.0 30.8 14.35 12.10
MA14D 24 FC/MC62D 1400 41.0 31.0 14.45 12.05
MA16C 21 FC/MC48C 1600 46.5 32.8 14.50 12.00
MA20D 24 FC/MC48D 1600 46.5 32.8 14.50 12.00
MA16C 21 FC/MC60C 1600 46.5 32.6 14.50 12.00
MA20D 24 FC/MC60D 1600 46.5 32.6 14.50 12.00
MA20D 24 FC/MC62D 1600 47.0 32.8 14.50 12.00
14.5 SEER AC WITH MV - VARIABLE SPEED
MV12B 17 FC/MC24B 800 25.4 17.7 16.00 13.20
MV12B 17 FC/MC30B 800 25.4 17.7 16.00 13.20
MV12B 17 FC/MC35B 800 25.6 18.0 16.00 13.50
MV16C 21 FC/MC35C 800 25.6 18.0 16.00 13.50
MV12B 17 FC/MC36B 800 25.6 18.0 16.00 13.50
MV16C 21 FC/MC36C 800 25.6 18.0 16.00 13.50
MV12B 17 FC/MC43B 800 25.8 18.4 16.10 13.75
MV16C 21 FC/MC43C 800 25.8 18.4 16.10 13.75
MV16C 21 FC/MC48C 800 26.2 18.7 16.50 14.00
MV12B 17 FC/MC30B 1000 29.4 21.0 15.00 12.85
MV12B 17 FC/MC35B 1000 29.6 21.4 15.25 13.00
MV16C 21 FC/MC35C 1000 29.6 21.4 15.50 13.25
MV12B 17 FC/MC36B 1000 29.6 21.4 15.30 13.15
MV16C 21 FC/MC36C 1000 29.6 21.4 15.50 13.15
MV12B 17 FC/MC43B 1000 30.2 22.0 15.75 13.25
MV16C 21 FC/MC43C 1000 30.2 22.0 16.00 13.50
MV16C 21 FC/MC48C 1000 30.6 22.2 16.00 13.50
MV20D 24 FC/MC48D 1000 30.6 22.2 16.00 13.50
MV12B 17 FC/MC35B 1200 35.0 25.8 15.00 12.50
MV16C 21 FC/MC35C 1200 35.2 26.0 15.75 13.00
MV12B 17 FC/MC36B 1200 34.8 25.4 15.00 12.75
MV16C 21 FC/MC36C 1200 35.0 25.6 15.50 13.00
MV12B 17 FC/MC43B 1200 35.8 26.4 15.50 13.00
MV16C 21 FC/MC43C 1200 36.0 26.6 16.00 13.25
MV12D 24 FC/MC48D 1150 36.0 26.4 16.00 13.50
MV16C 21 FC/MC48C 1200 36.2 27.0 16.25 14.00
MV20D 24 FC/MC48D 1200 36.2 27.0 16.25 14.00
COIL
1
MODEL
14.5 SEER AC WITH MA
RATED
CFM
TOTAL SENS.
COOLING
NET MBH
SEER EER
Johnson Controls Unitary Products 5
413432-YTG-A-0608
COOLING CAPACITY - With Air Handler Coils (Continued)
UNIT
MODEL
AIR HANDLER
MODEL W
COIL
MODEL
1
RATED
CFM
TOTAL SENS.
14.5 SEER AC WITH MV - VARIABLE SPEED (Contimued)
MV16C 21 FC/MC43C 1400 41.0 30.8 15.00 12.75
MV16C 21 FC/MC48C 1400 41.5 31.2 15.50 13.00
TCGF42S41S1
MV20D 24 FC/MC48D 1400 42.0 31.4 15.50 13.00
MV20D 24 FC/MC60D 1400 41.5 31.4 15.50 13.00
MV20D 24 FC/MC62D 1400 42.0 31.4 15.75 13.00
MV16C 21 FC/MC48C 1600 47.0 33.0 15.25 12.75
TCGF48S41S1
MV20D 24 FC/MC48D 1600 47.0 33.0 15.25 12.75
MV20D 24 FC/MC60D 1600 47.0 33.0 15.25 12.75
MV20D 24 FC/MC62D 1600 47.5 33.2 15.25 12.75
TCGF60S41S1
MV20D 24 FC/MC60D 1800 55.0 39.0 14.00 11.95
MV20D 24 FC/MC62D 1800 57.0 39.5 14.50 12.25
14.5 SEER AC WITH AV / SV / F*FV - VARIABLE SPEED
TCGF24S41S1
AV24 17 - 750 25.0 17.5 15.75 13.25
AV36 21 - 750 25.8 18.2 16.50 13.75
TCGF30S41S1 AV36 21 - 1000 30.4 22.4 16.25 13.50
AV36 21 - 1250 36.2 27.4 15.75 13.25
TCGF36S41S1
AV/SV48 24 - 1200 34.4 25.4 15.25 13.00
F4FV060 24 - 1200 34.6 25.6 15.50 13.25
AV/SV48 24 - 1400 40.0 29.4 14.75 12.50
TCGF42S41S1
AV/SV60 24 - 1400 40.0 29.4 14.75 12.50
F4FV060 24 - 1350 40.0 29.6 15.00 12.50
AV/SV48 24 - 1600 44.5 30.8 14.25 12.00
TCGF48S41S1
AV/SV60 24 - 1650 44.0 30.6 14.25 12.00
F4FV060 24 - 1600 44.5 30.6 14.25 12.00
TCGF60S41S1 AV/SV60 24 - 1750 55.0 39.0 14.00 12.00
14.5 SEER AC WITH AHP / SHP / F*FP
TCGF24S41S1
AHP24 17 - 850 24.8 17.4 14.30 12.20
F4FP030 17 - 800 24.8 17.2 14.30 12.20
TCGF30S41S1 AHP36 21 - 1000 29.6 21.4 14.30 12.20
AHP36 21 - 1200 35.4 26.2 15.00 12.50
F4FP036 21 - 1200 34.2 25.2 14.00 12.00
TCGF36S41S1
F4FP040 21 - 1200 34.4 25.0 14.00 12.00
F4FP042 21 - 1200 34.4 25.0 14.00 12.00
F5FP048 24 - 1250 36.4 27.4 16.25 13.50
F5FP060 24 - 1250 34.8 26.0 15.25 13.00
TCGF42S41S1
F5FP048 24 - 1450 42.0 32.0 15.50 13.00
F5FP060 24 - 1500 40.0 29.8 14.75 12.50
AHP/SHP60 24 - 1600 44.0 30.6 14.20 12.00
TCGF48S41S1
F5FP048 24 - 1700 47.5 34.0 15.00 12.75
F5FP060 24 - 1700 44.5 31.2 14.00 12.00
Rated in accordance with DOE test procedures (Federal Register 12-27-79 and 3-18-88) and ARI Standards 210.
Cooling MBH based on 80°F entering air temperature, 50% RH, and rated air flow.
EER (Energy Efficiency Ratio) is the total cooling output in BTU’s at 95°F outdoor ambient divided by the total electric power in watt-hours at those conditions.
SEER (Seasonal Energy Efficiency Ratio) is the total cooling output in BTU’s during a normal annual usage period for cooling divided by the total electric power
input in watt-hours during the same period.
COOLING
NET MBH
SEER EER
1. MC coils available with a factory installed horizontal drain pan. See price pages for specific model number.
— = Not applicable.
6 Johnson Controls Unitary Products
COOLING CAPACITY - Upflow, Downflow & Horizontal Furnaces and Coils
FURNACE**
UNIT MODEL
TCGF24S41S1
TCGF30S41S1
TCGF36S41S1
TCGF42S41S1
TCGF48S41S1
TCGF60S41S1
1. Requires a 2FD06700224 Blower Time Delay unless a standard furnace is equipped with one.
** Refer to Quick Selection Chart for specific furnace match-up.
CFM RANGE
(Min.-max.)
600 - 1000 14,17 FC/MC/PC24 800 24.8 17.3 14.00 12.00
600 - 1000 14,17 FC/MC/PC30 800 24.8 17.3 14.00 12.00
600 - 1000 14 FC/MC/PC32 800 25 17.6 14.50 12.35
600 - 1000 17,21 FC/MC/PC35 800 25 17.6 14.50 12.35
600 - 1000 14,17,21 FC/MC/PC36 800 25 17.6 14.00 12.00
600 - 1000 14 FC/MC/PC37 800 25.4 17.9 14.50 12.35
600 - 1000 17,21 FC/MC/PC43 800 25.2 18 14.70 12.50
600 - 1000 21 FC/MC/PC48 800 25.6 18.3 14.80 12.65
600 - 1000 14 HC18 800 24.2 16.7 14.00 12.00
600 - 1000 14 HC30 800 24.8 17.4 14.00 12.00
600 - 1000 17 HC36 800 25 17.6 14.00 12.00
600 - 1000 21 HC42 800 25.4 18 14.50 12.35
600 - 1000 14,17 HD24 800 25.4 17.7 14.50 12.35
600 - 1000 14,17,21 HD36 800 24.8 17 14.00 12.00
600 - 1000 21 HD48 800 25.6 17.9 14.50 12.35
600 - 1000 14,17 UC24 800 25 17.5 14.00 12.00
600 - 1000 14,17 UC30 800 25 17.5 14.00 12.00
800 - 1200 14,17 FC/MC/PC30 1000 28.8 20.6 14.00 12.00
800 - 1200 14,17 FC/MC/PC32 1000 29 21 14.00 12.00
800 - 1200 17,21 FC/MC/PC35 1000 29 21 14.00 12.00
800 - 1200 14,17,21 FC/MC/PC36 1000 29 21 14.00 12.00
800 - 1200 14 FC/MC/PC37 1000 29.6 21.6 14.50 12.35
800 - 1200 17,21 FC/MC/PC43 1000 29.6 21.6 14.50 12.35
800 - 1200 21,24 FC/MC/PC48 1000 30 21.8 14.50 12.35
800 - 1200 17 HC36 1000 29 21 14.00 12.00
800 - 1200 21 HC42 1000 29.6 21.6 14.25 12.10
800 - 1200 14,17,21 HD36 1000 28.8 20.2 14.00 12.00
800 - 1200 21,24 HD48 1000 29.8 21.4 14.50 12.35
800 - 1200 14,17 UC30 1000 29 20.8 14.00 12.00
1000 - 1400 17,21 FC/MC/PC35 1200 33.6 24.6 14.00 11.90
1000 - 1400 14,17,21 FC/MC/PC36 1200 33.4 24.2 14.00 11.85
1000 - 1400 14 FC/MC/PC37 1200 34.4 25.2 14.50 12.20
1000 - 1400 17,21 FC/MC/PC43 1200 34.4 25.2 14.50 12.20
1000 - 1400 21,24 FC/MC/PC48 1200 34.6 25.4 14.50 12.25
1000 - 1400 17 HC36 1200 33.6 24.6 14.00 11.90
1000 - 1400 21 HC42 1200 34.4 25.2 14.50 12.20
1000 - 1400 14,17,21,24 HD48 1200 34.6 25 14.50 12.20
1000 - 1400 21,24 UC60 1200 33.2 23.8 14.00 11.75
1200 - 1600 17,21 FC/MC/PC43 1400.00 40.50 30.40 14.00 12.00
1200 - 1600 21,24 FC/MC/PC48 1400.00 41.00 30.80 14.50 12.30
1200 - 1600 21,24 FC/MC/PC60 1400.00 41.00 30.80 14.50 12.30
1200 - 1600 21 HC42 1400.00 40.50 30.40 14.00 12.00
1200 - 1600 14,17,21,24 HD48 1400.00 41.00 30.40 14.25 12.10
1200 - 1600 21,24 HD60 1400.00 41.50 31.20 14.50 12.30
1200 - 1600 21,24 FC/MC62 1400.00 41.00 31.00 14.50 12.30
1400 - 1800 21,24 FC/MC/PC48 1600.00 46.50 32.80 14.25 12.10
1400 - 1800 21,24 FC/MC/PC60 1600.00 46.50 32.60 14.50 12.35
1400 - 1800 14,17,21,24 HD48 1600.00 46.50 32.60 14.50 12.35
1400 - 1800 14,17,21,24 HD60 1600.00 47.50 33.20 14.50 12.35
1400 - 1800 21,24 FC/MC62 1600.00 47.00 32.80 14.50 12.35
1600 - 2000 21,24 FC/MC/PC60 1800.00 54.50 38.50 13.80 11.90
1600 - 2000 24 HC60 1800.00 54.50 38.50 13.50 11.65
1600 - 2000 21,24 FC/MC62 1800.00 57.00 39.00 14.00 12.10
W
COIL
MODEL
RATED
CFM
TOTAL SENS.
COOLING
NET MBH
413432-YTG-A-0608
1
SEER
EER
Johnson Controls Unitary Products 7
413432-YTG-A-0608
COOLING CAPACITY - With Variable Speed Furnaces
UNIT MODEL
TCGF24S41S1
TCGF30S41S1
For Notes See Page 9.
VARIABLE SPEED
FURNACE MODEL
14.5 SEER AC WITH VARIABLE SPEED FURNACES
PV8*A12 FC/MC/PC24A 14 750 24.8 17.5 15.75 12.25
PV9*A12 FC/MC/PC24A 14 800 25.2 17.6 15.50 13.25
P(C,V)9*B12 FC/MC/PC24B 17 800 25.4 17.6 15.75 13.25
PV8*A12 FC/MC/PC30A 14 750 24.8 17.5 15.75 13.25
PV9*A12 FC/MC/PC30A 14 800 25.2 17.6 15.50 13.25
P(C,V)9*B12 FC/MC/PC30B 17 800 25.4 17.6 15.75 13.25
PV8*A12 FC/MC/PC32A 14 750 25.2 17.6 16.00 13.50
PV9*A12 FC/MC/PC32A 14 800 25.4 17.8 15.25 13.00
P(C,V)9*B12 FC/MC/PC35B 17 800 25.4 17.9 15.75 13.25
P(C,V)9*C16 FC/MC/PC35C 21 850 25.8 18.6 16.25 13.75
PV8*A12 FC/MC/PC36A 14 750 25.2 17.6 16.00 13.50
PV9*A12 FC/MC/PC36A 14 800 25.4 17.9 15.75 13.25
P(C,V)9*B12 FC/MC/PC36B 17 800 25.6 17.9 15.75 13.50
P(C,V)9*C16 FC/MC/PC36C 21 850 25.8 18.6 16.00 13.50
PV8*A12 FC/MC/PC37A 14 800 25.8 18.3 16.00 13.50
PV9*A12 FC/MC/PC37A 14 800 25.8 18.2 15.75 13.25
P(C,V)9*B12 FC/MC/PC43B 17 800 25.8 18.3 16.00 13.50
P(C,V)9*C16 FC/MC/PC43C 21 850 26.4 18.9 16.25 13.75
P(C,V)9*C16 FC/MC/PC48C 21 850 26.6 19.2 16.50 14.00
PV8*A12 HC24A 14 750 24.4 16.8 15.25 13.00
PV9*A12 HC24A 14 800 24.4 16.9 14.75 12.50
PV8*A12 HC30A 14 750 24.8 17.4 15.75 13.25
PV9*A12 HC30A 14 800 25.2 17.7 15.50 13.25
P(C,V)9*B12 HC36B 17 800 25.4 17.9 15.75 13.50
P(C,V)9*C16 HC42C 21 850 26.4 18.9 16.25 13.75
PV8*A12 HD24 14 750 25.8 17.8 16.25 13.75
PV9*A12 HD24 14 800 25.8 18.0 16.00 13.50
PV8*A12 HD36 14 750 25.0 17.0 15.50 13.25
PV9*A12 HD36 14 800 25.2 17.2 15.50 13.25
P(C,V)9*B12 HD36 17 800 25.2 17.3 15.50 13.25
P(C,V)9*C16 HD48 21 850 26.4 19.0 16.50 14.00
PV8*A12 UC24A 14 750 25.2 17.5 16.00 13.50
PV9*A12 UC24A 14 800 25.4 17.8 15.75 13.25
P(C,V)9*B12 UC24B 17 800 25.4 17.8 15.75 13.25
PV8*A12 UC30A 14 750 25.2 17.5 15.75 13.25
PV9*A12 UC30A 14 800 25.4 17.8 15.75 13.25
P(C,V)9*B12 UC30B 17 800 25.4 17.8 15.75 13.25
PV8*A12 FC/MC/PC30A 14 1000 29.2 21.0 15.00 12.75
PV8*B16 FC/MC/PC30B 17 1050 29.6 21.6 15.25 13.00
PV9*A12 FC/MC/PC30A 14 1000 29.2 20.8 15.00 12.75
P(C,V)9*B12 FC/MC/PC30B 17 1000 29.4 21.0 15.25 13.00
PV8*A12 FC/MC/PC32A 14 1000 29.6 21.4 15.25 13.00
PV9*A12 FC/MC/PC32A 14 1000 29.4 21.4 15.00 12.75
PV8*B16 FC/MC/PC35B 17 1050 30.0 22.0 15.75 13.25
PV8*C16 FC/MC/PC35C 21 1000 29.8 21.6 15.75 13.25
PV8*C20 FC/MC/PC35C 21 1100 30.2 22.8 15.75 13.25
P(C,V)9*B12 FC/MC/PC35B 17 1000 29.6 21.4 15.50 13.00
P(C,V)9*C16 FC/MC/PC35C 21 1000 29.6 21.4 15.50 13.00
P(C,V)9*C20 FC/MC/PC35C 21 1050 29.6 21.4 15.25 13.00
COIL
MODEL
1
COOLING
W
RATED
CFM
Net MBH
TOTAL SENS.
2
SEER EER
8 Johnson Controls Unitary Products
COOLING CAP ACITY - With Variable Speed Furnaces (Continued)
UNIT MODEL
TCGF30S41S1
TCGF36S41S1
For Notes See Page 9.
VARIABLE SPEED
FURNACE MODEL
14.5 SEER AC WITH VARIABLE SPEED FURNACES
PV8*A12 FC/MC/PC36A 14 1000 29.4 21.2 15.25 13.00
PV8*B16 FC/MC/PC36B 17 1050 29.8 22.0 15.75 13.25
PV8*C16 FC/MC/PC36C 21 1000 29.6 21.4 15.75 13.25
PV8*C20 FC/MC/PC36C 21 1100 30.2 22.6 15.75 13.25
PV9*A12 FC/MC/PC36A 14 1000 29.4 21.2 15.00 12.75
P(C,V)9*B12 FC/MC/PC36B 17 1000 29.6 21.4 15.50 13.00
P(C,V)9*C16 FC/MC/PC36C 21 1000 29.6 21.4 15.50 13.00
P(C,V)9*C20 FC/MC/PC36C 21 1050 29.6 21.4 15.50 13.00
PV8*A12 FC/MC/PC37A 14 1000 30.0 21.8 15.25 13.00
PV9*A12 FC/MC/PC37A 14 1000 30.0 21.8 15.00 12.75
PV8*B16 FC/MC/PC43B 17 1050 30.6 22.6 16.25 13.50
PV8*C16 FC/MC/PC43C 21 1000 30.2 22.0 16.25 13.50
PV8*C20 FC/MC/PC43C 21 1100 30.8 23.4 16.25 13.75
P(C,V)9*B12 FC/MC/PC43B 17 1000 30.2 22.0 16.00 13.25
P(C,V)9*C16 FC/MC/PC43C 21 1000 30.2 22.0 16.00 13.25
P(C,V)9*C20 FC/MC/PC43C 21 1050 30.2 22.0 16.00 13.25
PV8*C16 FC/MC/PC48C 21 1000 30.6 22.2 16.25 13.75
PV8*C20 FC/MC/PC48C 21 1100 31.2 23.6 16.50 13.75
P(C,V)9*C16 FC/MC/PC48C 21 1000 30.4 22.2 16.00 13.50
P(C,V)9*C20 FC/MC/PC48C 21 1050 30.4 22.2 16.00 13.50
P(C,V)9*D20 FC/MC/PC48D 24 1050 30.8 22.8 16.25 13.75
PV9*A12 HC30A 14 1000 29.0 21.0 15.00 12.50
PV8*B16 HC36B 17 1050 30.0 22.0 15.75 13.25
P(C,V)9*B12 HC36B 17 1000 29.6 21.4 15.50 13.25
PV8*C16 HC42C 21 1000 30.2 22.0 16.25 13.50
PV8*C20 HC42C 21 1100 31.0 23.4 16.25 13.75
P(C,V)9*C16 HC42C 21 1000 30.2 22.0 15.75 13.25
P(C,V)9*C20 HC42C 21 1050 30.2 22.0 15.75 13.25
PV8*A12 HD36 14 1000 29.2 20.6 15.00 12.75
PV8*B16 HD36 17 1050 29.6 21.6 15.50 13.25
PV8*C16 HD36 21 1000 29.4 20.8 15.75 13.25
PV8*C20 HD36 21 1100 30.0 22.0 16.00 13.50
PV9*A12 HD36 14 1000 29.2 20.6 14.75 12.75
P(C,V)9*B12 HD36 17 1000 29.4 20.6 15.25 13.00
PV8*C16 HD48 21 1000 30.6 21.8 16.50 13.75
PV8*C20 HD48 21 1100 31.2 23.2 16.50 14.00
P(C,V)9*C16 HD48 21 1000 30.4 21.8 16.00 13.50
P(C,V)9*C20 HD48 21 1050 30.4 21.8 16.00 13.50
P(C,V)9*D20 HD48 24 1050 30.6 22.6 16.25 13.50
PV8*A12 UC30A 14 1000 29.4 21.2 15.25 13.00
PV8*B16 UC30B 17 1050 29.8 21.8 15.50 13.25
PV9*A12 UC30A 14 1000 29.4 21.2 15.00 12.75
PV8*B16 FC/MC/PC35B 17 1200 34.2 25.0 15.25 12.75
PV8*C16 FC/MC/PC35C 21 1200 34.2 25.0 15.50 12.75
PV8*C20 FC/MC/PC35C 21 1200 34.2 25.0 15.50 12.75
P(C,V)9*B12 FC/MC/PC35B 17 1200 34.0 24.8 14.75 12.25
P(C,V)9*C16 FC/MC/PC35C 21 1200 34.2 25.0 15.25 12.75
P(C,V)9*C20 FC/MC/PC35C 21 1200 34.2 25.0 15.25 12.75
PV8*A12 FC/MC/PC36A 14 1200 33.8 24.4 14.50 12.25
PV8*B16 FC/MC/PC36B 17 1200 34.0 24.6 15.00 12.75
PV8*C16 FC/MC/PC36C 21 1200 34.0 24.6 15.25 12.75
COIL
MODEL
1
W
RATED
CFM
COOLING
Net MBH
TOTAL SENS.
2
413432-YTG-A-0608
SEER EER
Johnson Controls Unitary Products 9
413432-YTG-A-0608
COOLING CAP ACITY - With Variable Speed Furnaces (Continued)
UNIT MODEL
TCGF36S41S1
TCGF42S41S1
For Notes See Page 9.
VARIABLE SPEED
FURNACE MODEL
14.5 SEER AC WITH VARIABLE SPEED FURNACES
PV8*C20 FC/MC/PC36C 21 1200 34.0 24.6 15.25 12.75
PV9*A12 FC/MC/PC36A 14 1200 33.6 24.2 14.25 12.00
P(C,V)9*B12 FC/MC/PC36B 17 1200 33.8 24.4 14.75 12.25
P(C,V)9*C16 FC/MC/PC36C 21 1200 34.0 24.6 15.25 12.75
P(C,V)9*C20 FC/MC/PC36C 21 1200 34.0 24.6 15.00 12.75
PV8*A12 FC/MC/PC37A 14 1150 34.6 25.2 14.75 12.25
PV9*A12 FC/MC/PC37A 14 1100 34.0 24.4 14.75 12.25
PV8*B16 FC/MC/PC43B 17 1200 35.0 25.4 15.75 13.00
PV8*C16 FC/MC/PC43C 21 1200 35.0 25.6 15.75 13.00
PV8*C20 FC/MC/PC43C 21 1200 35.0 25.6 16.00 13.25
P(C,V)9*B12 FC/MC/PC43B 17 1200 34.6 25.4 15.00 12.50
P(C,V)9*C16 FC/MC/PC43C 21 1200 35.0 25.6 15.75 13.00
P(C,V)9*C20 FC/MC/PC43C 21 1200 34.8 25.4 15.50 13.00
PV8*C16 FC/MC/PC48C 21 1200 35.4 26.0 16.25 13.25
PV8*C20 FC/MC/PC48C 21 1200 35.4 26.0 16.25 13.25
P(C,V)9*C16 FC/MC/PC48C 21 1200 35.2 25.8 16.00 13.25
P(C,V)9*C20 FC/MC/PC48C 21 1200 35.2 25.8 15.75 13.00
P(C,V)9*D20 FC/MC/PC48D 24 1200 35.2 25.8 16.00 13.25
PV8*B16 HC36B 17 1200 34.2 25.0 15.25 12.75
P(C,V)9*B12 HC36B 17 1200 34.0 24.8 15.00 12.50
PV8*C16 HC42C 21 1200 35.0 25.6 15.75 13.25
PV8*C20 HC42C 21 1200 35.0 25.6 16.00 13.25
P(C,V)9*C16 HC42C 21 1200 35.0 25.6 15.75 13.00
P(C,V)9*C20 HC42C 21 1200 34.8 25.4 15.50 13.00
PV8*C16 HD48 21 1200 35.2 25.6 16.00 13.25
PV8*C20 HD48 21 1200 35.2 25.6 16.00 13.50
P(C,V)9*C16 HD48 21 1200 35.2 25.4 15.75 13.25
P(C,V)9*C20 HD48 21 1200 35.0 25.4 15.75 13.00
P(C,V)9*D20 HD48 24 1200 35.2 25.4 15.75 13.25
PV8*C20 FC/MC62D 21 1200 35.6 26.0 16.25 13.50
P(C,V)9*C16 FC/MC62D 21 1200 35.4 26.0 16.00 13.25
P(C,V)9*C20 FC/MC62D 21 1200 35.4 26.0 15.75 13.25
P(C,V)9*D20 FC/MC62D 24 1200 35.4 26.0 16.00 13.25
PV8*C16 UC60C 21 1200 33.8 24.2 15.50 12.75
PV8*C20 UC60C 21 1200 33.8 24.2 15.50 12.75
P(C,V)9*C16 UC60C 21 1200 33.8 24.2 15.25 12.75
P(C,V)9*C20 UC60C 21 1200 33.6 24.2 15.25 12.50
P(C,V)9*D20 UC60D 24 1200 33.8 24.2 15.25 12.75
PV8*B16 FC/MC/PC43B 17 1400 41.0 30.6 14.75 12.50
PV8*C20 FC/MC/PC43C 21 1400 41.0 30.8 14.75 12.75
P(C,V)9*C16 FC/MC/PC43C 21 1400 41.0 30.6 14.50 12.50
P(C,V)9*C20 FC/MC/PC43C 21 1350 41.0 30.8 15.00 12.75
PV8*C16 FC/MC/PC48C 21 1400 41.5 31.2 15.00 12.75
PV8*C20 FC/MC/PC48C 21 1400 41.5 31.2 15.25 12.75
P(C,V)9*C16 FC/MC/PC48C 21 1400 41.5 31.0 15.00 12.50
P(C,V)9*C20 FC/MC/PC48C 21 1350 41.5 31.2 15.25 12.75
P(C,V)9*D20 FC/MC/PC48D 24 1350 41.5 31.2 15.50 13.00
PV8*C16 FC/MC/PC60C 21 1400 41.5 31.2 15.00 12.75
PV8*C20 FC/MC/PC60C 21 1400 41.5 31.2 15.25 12.75
P(C,V)9*C16 FC/MC/PC60C 21 1400 41.0 31.0 14.75 12.50
COIL
MODEL
1
W
RATED
CFM
COOLING
Net MBH
TOTAL SENS.
2
SEER EER
10 Johnson Controls Unitary Products
COOLING CAP ACITY - With Variable Speed Furnaces (Continued)
UNIT MODEL
TCGF42S41S1
TCGF48S41S1
TCGF60S41S1
1. MC coils available with a factory installed horizontal drain pan. See price pages for specific model number.
2. Variable speed furnaces have B.O.D (Blower on Delay) standard.
VARIABLE SPEED
FURNACE MODEL
14.5 SEER AC WITH VARIABLE SPEED FURNACES
P(C,V)9*C20 FC/MC/PC60C 21 1350 41.5 31.2 15.25 12.75
P(C,V)9*D20 FC/MC/PC60D 24 1350 41.5 31.2 15.50 13.00
PV8*C16 HC42C 21 1400 41.0 30.6 15.00 12.50
PV8*C20 HC42C 21 1400 41.0 30.8 15.00 12.75
P(C,V)9*C16 HC42C 21 1400 41.0 30.6 14.75 12.50
P(C,V)9*C20 HC42C 21 1350 41.0 30.8 15.00 12.75
PV8*C16 HD48 21 1400 41.5 30.6 15.00 12.75
PV8*C20 HD48 21 1400 41.5 30.8 15.25 12.75
P(C,V)9*C16 HD48 21 1400 41.0 30.6 14.75 12.50
P(C,V)9*C20 HD48 21 1350 41.5 30.6 15.25 12.75
P(C,V)9*D20 HD48 24 1350 41.5 30.8 15.50 13.00
PV8*C16 HD60 21 1400 42.0 31.4 15.25 13.00
PV8*C20 HD60 21 1400 42.0 31.6 15.50 13.00
P(C,V)9*C16 HD60 21 1400 42.0 31.4 15.00 12.75
P(C,V)9*C20 HD60 21 1350 42.0 31.6 15.50 13.00
P(C,V)9*D20 HD60 24 1350 42.0 31.6 15.75 13.25
PV8*C20 FC/MC62D 21 1400 41.5 31.2 15.50 13.00
P(C,V)9*C16 FC/MC62D 21 1400 41.5 31.2 15.00 12.75
P(C,V)9*C20 FC/MC62D 21 1350 41.5 31.2 15.25 13.00
P(C,V)9*D20 FC/MC62D 24 1350 42.0 31.4 15.75 13.00
PV8*C16 FC/MC/PC48C 21 1500 46.5 31.8 14.50 12.25
PV8*C20 FC/MC/PC48C 21 1600 47.0 32.8 14.75 12.50
P(C,V)9*C16 FC/MC/PC48C 21 1600 46.5 32.8 14.50 12.25
P(C,V)9*C20 FC/MC/PC48C 21 1600 47.0 32.8 14.75 12.50
PV8*C16 FC/MC/PC60C 21 1500 46.5 32.0 14.50 12.25
PV8*C20 FC/MC/PC60C 21 1600 47.0 32.8 14.75 12.50
P(C,V)9*C16 FC/MC/PC60C 21 1600 46.5 32.8 14.50 12.25
P(C,V)9*C20 FC/MC/PC60C 21 1600 47.0 32.8 14.75 12.50
P(C,V)9*D20 FC/MC/PC60D 24 1550 47.0 33.0 15.00 12.75
PV8*C16 HD48 21 1500 46.5 31.6 14.50 12.25
PV8*C20 HD48 21 1600 47.0 32.8 14.75 12.50
P(C,V)9*C16 HD48 21 1600 46.5 32.6 14.50 12.25
P(C,V)9*C20 HD48 21 1600 47.0 32.6 14.75 12.50
P(C,V)9*D20 HD48 24 1550 47.0 32.8 15.00 12.75
PV8*C16 HD60 21 1500 47.0 32.4 15.00 12.50
PV8*C20 HD60 21 1600 47.5 33.4 15.00 12.75
P(C,V)9*C16 HD60 21 1600 47.5 33.2 14.75 12.50
P(C,V)9*C20 HD60 21 1600 47.5 33.4 15.00 12.75
P(C,V)9*D20 HD60 24 1550 48.0 33.6 15.25 13.00
PV8*C20 FC/MC62D 21 1600 47.0 33.0 15.00 12.75
P(C,V)9*C16 FC/MC62D 21 1600 47.0 32.8 14.75 12.25
P(C,V)9*C20 FC/MC62D 21 1600 47.0 33.0 15.00 12.50
P(C,V)9*D20 FC/MC62D 24 1550 47.5 33.0 15.25 12.75
P(C,V)9*D20 HC60D 24 1600 53.5 36.4 13.50 11.75
PV8*C20 HD60 21 1750 56.5 39.0 13.75 12.00
P(C,V)9*C20 HD60 21 1650 56.5 39.0 14.00 12.25
P(C,V)9*D20 HD60 24 1600 56.0 37.8 14.25 12.25
PV8*C20 FC/MC62D 21 1750 57.0 39.5 14.25 12.25
P(C,V)9*C20 FC/MC62D 21 1650 56.0 38.0 13.75 12.00
P(C,V)9*D20 FC/MC62D 24 1600 56.0 37.8 14.00 12.25
COIL
MODEL
1
W
RATED
CFM
Net MBH
TOTAL SENS.
2
413432-YTG-A-0608
COOLING
SEER EER
Johnson Controls Unitary Products 11
413432-YTG-A-0608
ACCESSORIES
Refer to Price Manual for specific model numbers.
HARD START KIT - Required when using TXV indoor coil.
Also, provides increased starting torque for areas with low
voltage.
Model Source 1 Kit numbers
24 S1-2SA06721706
30 S1-2SA06705906
36 S1-2SA06708906
42 S1-2SA06708806
48 S1-2SA06708806
60 S1-2SA06707906
OFF CYCLE TIMER DELAY - Provides a 5-minute off cycle
to prevent rapid recycling of the compressor.
TYPICAL INSTALLATION
MINIMUM 18” SERVICE
60” OVERHEAD
CLEARANCE
ACCESS CLEARANCE
ON ONE SIDE
ROOM THERMOSTATS - A wide selection of compatible
thermosets are available to provide optimum performance
and features for any installation.
1H/1C, manual changeover electronic non-programmable
thermostat.
1H/1C, auto/manual changeover, electronic programmable,
deluxe 7-day, thermostat.
1H/1C, auto/manual changeover, electronic programmable.
* For the most current accessory information, refer to the
price book or consult factory.
SOUND POWER RATINGS*
UNIT MODEL (dBA)
24 TBD
30 TBD
36 TBD
42 TBD
48 TBD
60 TBD
* Rated in accordance with ARI 270-95 Standards.
THERMOSTAT
WEATHERPROOF
DISCONNECT
SWITCH
NEC CLASS 1 WIRING
6” CLEARANCE
AROUND PERIMETER
NOTE:
ALL OUTDOOR WIRING
MUST BE WEATHERPROOF.
TYPICAL FIELD WIRING
ALL FIELD WIRING TO BE IN ACCORDANCE WITH ELECTRIC CODE (NEC) AND/OR LOCAL CODES
POWER WIRING
208/230-1-60
CONTACTOR
GND.
LUG
TERMINALS
CONDENSING UNIT
ALL OUTDOOR WIRING MUST BE WEATHERPROOF. USE COPPER CONDUCTORS ONLY.
COIL
24 VOLT CONTROL WIRING
MINIMUM 18 GA. WIRE
(NEC CLASS 2)
TO FURNACE OR
AIR HANDLER
TERMINAL BLOCK
NEC CLASS 2 WIRING
TO INDOOR COIL
CONTROL
ACCESS
PANEL
FURNACE OR AIR HANDLER TERMINAL BLOCK
CYRGW
SEAL OPENING(S) WITH
PERMAGUM OR EQUIVALENT
R
Y
ROOM THERMOSTAT
GW
POWER WIRING
CONTROL WIRING
FACTORY WIRING
*
TERMINAL W IS ONLY
REQUIRED ON SYSTEMS
WITH HEAT.
*
12 Johnson Controls Unitary Products
413432-YTG-A-0608
COOLING PERFORMANCE DATA
AIR CONDITIONER MODEL NO. TCGF24S41S1
INDOOR COIL MODEL NO. FC/MC/PC32
CONDENSING
ENTERING AIR
TEMPERATURE
65
75
85
95
105
115
125
NOTE: ALL CAPACITIES INCLUDE I NDOOR FAN HEAT AT 1250 BTUH/1000 CFM.
Multipliers for determining the performance with other indoor sections.
For dry bulb temperatures different than those listed (between 73-87 F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the listed temperature and decreases by 1060 BTUH per 1000 CFM per degree below the listed temperature.
IDCFM 600 800 1000
ID DB (°F) 80 80 75 80 80 80 80 75 80 80 80 80 75 80 80
ID WB (°F) 57 62 62 67 72 57 62 62 67 72 57 62 62 67 72
T.C. 21.8 23.8 23.8 25.7 27.7 23.9 25.4 25.3 27.6 29.5 26.1 27.1 26.9 29.4 31.4
S.C. 16.3 16.3 16.3 16.1 14.4 16.3 16.3 16.3 16.2 15.3 16.3 16.3 16.3 16.3 16.2
KW 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2
T.C. 21.0 23.0 22.9 24.9 26.8 23.1 24.6 24.4 26.6 28.6 25.3 26.1 25.9 28.4 30.4
S.C. 16.3 16.3 15.8 15.7 13.9 16.3 16.3 16.0 16.0 14.9 16.3 16.3 16.3 16.3 15.9
KW 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4
T.C. 20.2 22.2 22.0 24.1 25.9 22.4 23.7 23.5 25.7 27.7 24.5 25.2 24.9 27.3 29.5
S.C. 16.3 16.3 15.2 15.3 13.4 16.3 16.3 15.8 15.8 14.4 16.3 16.3 16.3 16.3 15.5
KW 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6
T.C. 19.5 21.4 21.2 23.3 25.0 21.6 22.8 22.6 24.8 26.8 23.7 24.2 23.9 26.3 28.5
S.C. 16.3 16.3 14.7 15.0 12.9 16.3 16.3 15.5 15.6 14.0 16.3 16.3 16.3 16.3 15.1
KW 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8
T.C. 18.4 20.1 19.9 22.0 23.7 20.4 21.4 21.1 23.4 25.2 22.4 22.6 22.4 24.7 26.8
S.C. 16.3 15.9 14.0 14.2 12.2 16.3 16.1 15.2 15.3 13.3 16.3 16.3 16.3 16.3 14.4
KW 2.2 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.2
T.C. 17.4 18.8 18.6 20.7 22.3 19.3 19.9 19.7 21.9 23.7 21.2 21.0 20.9 23.1 25.1
S.C. 16.3 15.4 13.4 13.5 11.6 16.3 15.9 14.8 14.9 12.6 16.3 16.3 16.3 16.3 13.6
KW 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5
T.C. 16.3 17.5 17.3 19.3 20.9 18.1 18.4 18.3 20.4 22.2 19.9 19.4 19.3 21.6 23.4
S.C. 16.3 15.0 12.7 12.8 10.9 16.3 15.7 14.5 14.6 11.9 16.3 16.3 16.3 16.3 12.9
KW 2.9 2.9 2.9 2.9 2.8 2.9 2.9 2.9 2.8 2.8 2.8 2.8 2.9 2.8 2.8
Johnson Controls Unitary Products 13
413432-YTG-A-0608
Air Handler Coil T.C. S.C. KW
- FC/MC/PC24 1.02 1.04 1.02
- FC/MC/PC30 1.02 1.04 1.02
- FC/MC/PC35 1.02 1.06 1.02
- FC/MC/PC36 1.02 1.06 1.02
- FC/MC/PC37 1.04 1.08 1.02
- FC/MC/PC43 1.03 1.08 1.02
- FC/MC/PC48 1.05 1.10 1.02
- HC24 0.99 1.00 1.02
- HC30 1.01 1.04 1.02
- HC36 1.02 1.06 1.02
- HC42 1.04 1.08 1.02
- HD24 1.04 1.07 1.02
- HD36 1.01 1.02 1.02
- HD48 1.05 1.07 1.02
- UC24 1.02 1.05 1.02
- UC30 1.02 1.05 1.02
AHP24 - 1.01 1.04 1.01
AV24 - 1.02 1.05 0.93
AV36 - 1.05 1.09 0.93
F4FP030 - 1.02 1.04 1.02
MA08B FC/MC24B 1.02 1.04 1.02
MV12B FC/MC24B 1.04 1.07 0.94
MA08B FC/MC30B 1.02 1.04 1.02
MV12B FC/MC30B 1.04 1.07 0.94
MA08B FC/MC35B 1.02 1.06 1.02
MV12B FC/MC35B 1.05 1.08 0.93
MV16C FC/MC35C 1.05 1.08 0.93
MA08B FC/MC36B 1.02 1.06 1.02
MV12B FC/MC36B 1.05 1.08 0.93
MV16C FC/MC36C 1.05 1.08 0.93
MA08B FC/MC43B 1.03 1.08 1.02
MV12B FC/MC43B 1.06 1.10 0.94
MV16C FC/MC43C 1.06 1.10 0.93
MV16C FC/MC48C 1.07 1.12 0.93
Variable Speed
Furnace
PV8*A12 FC/MC/PC24A 1.02 1.05 0.94
PV9*A12 FC/MC/PC24A 1.03 1.06 0.96
P(C,V)9*B12 FC/MC/PC24B 1.03 1.06 0.95
PV8*A12 FC/MC/PC30A 1.02 1.05 0.94
PV9*A12 FC/MC/PC30A 1.03 1.06 0.96
P(C,V)9*B12 FC/MC/PC30B 1.03 1.06 0.95
PV8*A12 FC/MC/PC32A 1.03 1.06 0.94
PV9*A12 FC/MC/PC32A 1.03 1.07 0.97
P(C,V)9*B12 FC/MC/PC35B 1.04 1.07 0.95
P(C,V)9*C16 FC/MC/PC35C 1.06 1.12 0.94
PV8*A12 FC/MC/PC36A 1.03 1.06 0.94
PV9*A12 FC/MC/PC36A 1.04 1.07 0.96
P(C,V)9*B12 FC/MC/PC36B 1.04 1.08 0.95
P(C,V)9*C16 FC/MC/PC36C 1.06 1.12 0.94
PV8*A12 FC/MC/PC37A 1.06 1.10 0.95
PV9*A12 FC/MC/PC37A 1.05 1.10 0.96
P(C,V)9*B12 FC/MC/PC43B 1.05 1.10 0.95
P(C,V)9*C16 FC/MC/PC43C 1.08 1.14 0.94
P(C,V)9*C16 FC/MC/PC48C 1.08 1.15 0.94
PV8*A12 HC24A 1.00 1.01 0.94
PV9*A12 HC24A 1.00 1.01 0.97
PV8*A12 HC30A 1.02 1.05 0.94
PV9*A12 HC30A 1.03 1.06 0.96
P(C,V)9*B12 HC36B 1.04 1.08 0.95
P(C,V)9*C16 HC42C 1.08 1.14 0.94
PV8*A12 HD24 1.05 1.07 0.94
PV9*A12 HD24 1.05 1.08 0.96
PV8*A12 HD36 1.02 1.02 0.94
PV9*A12 HD36 1.03 1.04 0.96
P(C,V)9*B12 HD36 1.03 1.04 0.95
P(C,V)9*C16 HD48 1.08 1.14 0.94
PV8*A12 UC24A 1.03 1.05 0.94
PV9*A12 UC24A 1.04 1.07 0.96
P(C,V)9*B12 UC24B 1.04 1.07 0.95
PV8*A12 UC30A 1.03 1.05 0.94
PV9*A12 UC30A 1.04 1.07 0.96
P(C,V)9*B12 UC30B 1.04 1.07 0.95
Coil T.C. S.C. KW
14 Johnson Controls Unitary Products
413432-YTG-A-0608
COOLING PERFORMANCE DATA
AIR CONDITIONER MODEL NO. TCGF30S41S1
INDOOR COIL MODEL NO. FC/MC/PC43
CONDENSING
ENTERING AIR
TEMPERATURE
65
75
85
95
105
115
125
NOTE: ALL CAPACITIES INCLUDE I NDOOR FAN HEAT AT 1250 BTUH/1000 CFM.
Multipliers for determining the performance with other indoor sections.
NOTE: For dry bulb temperatures different than those listed (between 73-87 F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the
listed temperature and decreases by 1060 BTUH per 1000 CFM per degree below the listed temperature.
IDCFM 800 1000 1200
ID DB (°F) 80 80 75 80 80 80 80 75 80 80 80 80 75 80 80
ID WB (°F) 57 62 62 67 72 57 62 62 67 72 57 62 62 67 72
T.C. 28.2 30.1 29.9 32.9 35.2 29.8 31.3 31.2 34.1 36.4 31.5 32.5 32.6 35.3 37.5
S.C. 27.1 24.4 21.3 20.9 17.2 29.1 27.4 23.5 23.3 18.9 31.1 30.4 25.8 25.7 20.6
KW 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4 1.4
T.C. 27.3 28.8 28.7 31.4 33.9 28.8 30.0 29.9 32.6 35.0 30.3 31.2 31.0 33.8 36.1
S.C. 26.2 24.0 20.7 20.4 16.6 28.0 26.7 23.0 22.8 18.3 29.9 29.5 25.2 25.1 19.9
KW 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6
T.C. 26.4 27.5 27.6 29.9 32.5 27.8 28.7 28.6 31.1 33.6 29.2 29.8 29.5 32.3 34.8
S.C. 25.2 23.5 20.2 19.9 16.0 26.9 26.1 22.4 22.2 17.6 28.7 28.7 24.6 24.5 19.2
KW 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8
T.C. 25.5 26.2 26.5 28.4 31.1 26.8 27.4 27.2 29.6 32.3 28.1 28.5 28.0 30.8 33.4
S.C. 24.3 23.0 19.6 19.3 15.4 25.9 25.4 21.8 21.6 17.0 27.5 27.9 24.0 23.9 18.5
KW 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0
T.C. 23.9 24.5 24.6 26.9 29.5 25.3 25.9 25.4 28.0 30.6 26.6 27.3 26.2 29.1 31.7
S.C. 22.8 21.7 18.5 18.7 15.0 24.5 24.1 20.7 21.1 16.6 26.2 26.6 22.9 23.4 18.2
KW 2.5 2.5 2.5 2.4 2.3 2.4 2.4 2.4 2.4 2.3 2.4 2.4 2.4 2.4 2.3
T.C. 22.3 22.7 22.9 25.4 28.0 23.8 24.4 23.6 26.5 29.0 25.2 26.0 24.4 27.5 30.0
S.C. 21.4 20.5 17.4 18.1 14.6 23.2 22.9 19.6 20.5 16.2 24.9 25.3 21.8 23.0 17.8
KW 2.9 2.9 2.9 2.7 2.7 2.8 2.8 2.8 2.7 2.7 2.7 2.7 2.8 2.7 2.7
T.C. 20.8 21.0 21.1 24.0 26.4 22.3 22.9 21.9 24.9 27.4 23.8 24.8 22.7 25.9 28.3
S.C. 20.0 19.3 16.3 17.4 14.1 21.9 21.6 18.5 20.0 15.8 23.7 24.0 20.7 22.5 17.5
KW 3.3 3.3 3.3 3.1 3.0 3.2 3.2 3.2 3.1 3.0 3.0 3.0 3.2 3.0 3.0
Johnson Controls Unitary Products 15
413432-YTG-A-0608
Air Handler Coil T.C. S.C. KW
- FC/MC/PC30 0.97 0.95 1.00
- FC/MC/PC32 0.98 0.98 1.00
- FC/MC/PC35 0.98 0.98 1.00
- FC/MC/PC36 0.98 0.97 1.00
- FC/MC/PC37 1.00 1.00 1.00
- FC/MC/PC42 0.94 0.95 1.00
- FC/MC/PC48 1.01 1.01 1.00
- FC/MC/PC60 1.00 1.01 1.00
- HC36 0.98 0.98 1.00
- HC42 1.00 1.00 1.00
- HD36 0.97 0.94 1.00
- HD48 1.01 0.99 1.00
- UC30 0.98 0.96 1.00
AHP36 - 1.00 1.00 1.00
AV36 - 1.03 1.04 0.92
MA12B FC/MC30B 0.97 0.95 1.00
MV12B FC/MC30B 0.99 0.97 0.93
MA12B FC/MC35B 0.98 0.98 1.00
MV12B FC/MC35B 1.00 0.99 0.93
MV16C FC/MC35C 1.00 1.00 0.93
MA12B FC/MC36B 0.98 0.97 1.00
MV12B FC/MC36B 1.00 0.99 0.93
MV16C FC/MC36C 1.00 0.99 0.93
MA12B FC/MC43B 1.00 1.00 1.00
MV12B FC/MC43B 1.02 1.02 0.93
MV16C FC/MC43C 1.02 1.02 0.92
MV16C FC/MC48C 1.03 1.03 0.92
MV20D FC/MC48D 1.03 1.03 0.93
Variable Speed
Furnace
PV8*A12 FC/MC/PC30A 0.99 0.97 0.94
PV8*B16 FC/MC/PC30B 1.00 1.00 0.93
PV9*A12 FC/MC/PC30A 0.99 0.97 0.95
P(C,V)9*B12 FC/MC/PC30B 0.99 0.97 0.93
PV8*A12 FC/MC/PC32A 1.00 0.99 0.94
PV9*A12 FC/MC/PC32A 1.00 0.99 0.96
PV8*B16 FC/MC/PC35B 1.01 1.02 0.93
PV8*C16 FC/MC/PC35C 1.00 1.00 0.92
PV8*C20 FC/MC/PC35C 1.02 1.05 0.94
P(C,V)9*B12 FC/MC/PC35B 1.00 0.99 0.94
P(C,V)9*C16 FC/MC/PC35C 1.00 0.99 0.94
P(C,V)9*C20 FC/MC/PC35C 1.00 0.99 0.94
PV8*A12 FC/MC/PC36A 1.00 0.98 0.94
PV8*B16 FC/MC/PC36B 1.01 1.02 0.93
PV8*C16 FC/MC/PC36C 1.00 0.99 0.92
PV8*C20 FC/MC/PC36C 1.02 1.04 0.94
PV9*A12 FC/MC/PC36A 0.99 0.98 0.95
P(C,V)9*B12 FC/MC/PC36B 1.00 0.99 0.93
P(C,V)9*C16 FC/MC/PC36C 1.00 0.99 0.93
P(C,V)9*C20 FC/MC/PC36C 1.00 0.99 0.93
PV8*A12 FC/MC/PC37A 1.01 1.01 0.96
PV9*A12 FC/MC/PC37A 1.01 1.01 0.97
PV8*B16 FC/MC/PC43B 1.03 1.05 0.93
PV8*C16 FC/MC/PC43C 1.02 1.02 0.92
PV8*C20 FC/MC/PC43C 1.04 1.08 0.93
P(C,V)9*B12 FC/MC/PC43B 1.02 1.02 0.93
P(C,V)9*C16 FC/MC/PC43C 1.02 1.02 0.93
P(C,V)9*C20 FC/MC/PC43C 1.02 1.02 0.93
PV8*C16 FC/MC/PC48C 1.03 1.03 0.92
PV8*C20 FC/MC/PC48C 1.05 1.09 0.93
P(C,V)9*C16 FC/MC/PC48C 1.03 1.03 0.93
P(C,V)9*C20 FC/MC/PC48C 1.03 1.03 0.93
P(C,V)9*D20 FC/MC/PC48D 1.04 1.06 0.93
PV9*A12 HC30A 0.98 0.97 0.95
PV8*B16 HC36B 1.01 1.02 0.93
P(C,V)9*B12 HC36B 1.00 0.99 0.93
PV8*C16 HC42C 1.02 1.02 0.92
PV8*C20 HC42C 1.05 1.08 0.93
P(C,V)9*C16 HC42C 1.02 1.01 0.93
P(C,V)9*C20 HC42C 1.02 1.01 0.93
PV8*A12 HD36 0.99 0.96 0.94
PV8*B16 HD36 1.00 1.00 0.93
PV8*C16 HD36 1.00 0.96 0.92
PV8*C20 HD36 1.01 1.02 0.92
PV9*A12 HD36 0.99 0.95 0.95
P(C,V)9*B12 HD36 0.99 0.96 0.93
PV8*C16 HD48 1.03 1.01 0.92
PV8*C20 HD48 1.05 1.08 0.92
P(C,V)9*C16 HD48 1.03 1.01 0.93
P(C,V)9*C20 HD48 1.03 1.01 0.93
PV8*A12 UC30A 0.99 0.98 0.94
PV8*B16 UC30B 1.01 1.01 0.93
PV9*A12 UC30A 0.99 0.98 0.95
P(C,V)9*B12 UC30B 1.00 0.98 0.93
Coil T.C. S.C. KW
16 Johnson Controls Unitary Products
413432-YTG-A-0608
COOLING PERFORMANCE DATA
AIR CONDITIONER MODEL NO. TCGF36S41S1
INDOOR COIL MODEL NO. FC/MC/PC43
CONDENSING
ENTERING AIR
TEMPERATURE
65
75
85
95
105
115
125
NOTE: ALL CAPACITIES INCLUDE I NDOOR FAN HEAT AT 1250 BTUH/1000 CFM.
Multipliers for determining the performance with other indoor sections.
NOTE: For dry bulb temperatures different than those listed (between 73-87 F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the
listed temperature and decreases by 1060 BTUH per 1000 CFM per degree below the listed temperature.
IDCFM 1000 1200 1400
ID DB (°F) 80 80 75 80 80 80 80 75 80 80 80 80 75 80 80
ID WB (°F) 57 62 62 67 72 57 62 62 67 72 57 62 62 67 72
T.C. 32.5 34.9 34.7 37.5 40.6 34.2 35.8 35.7 38.4 41.8 35.8 36.8 36.7 39.3 43.0
S.C. 25.5 25.5 24.9 24.8 20.9 25.5 25.5 25.2 25.2 21.7 25.5 25.5 25.5 25.5 22.4
KW 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6
T.C. 31.6 33.6 33.4 36.3 39.1 33.2 34.5 34.3 37.1 40.2 34.8 35.3 35.3 38.0 41.3
S.C. 25.5 25.5 24.2 24.2 20.2 25.5 25.5 24.9 24.9 21.0 25.5 25.5 25.5 25.5 21.8
KW 1.8 1.9 1.9 1.9 1.9 1.8 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9
T.C. 30.7 32.3 32.1 35.0 37.7 32.2 33.1 33.0 35.9 38.7 33.7 33.9 33.8 36.7 39.6
S.C. 25.5 25.5 23.6 23.6 19.4 25.5 25.5 24.6 24.6 20.3 25.5 25.5 25.5 25.5 21.3
KW 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1 2.1
T.C. 29.7 31.0 30.8 33.7 36.2 31.2 31.7 31.6 34.6 37.1 32.6 32.5 32.4 35.4 37.9
S.C. 25.5 25.5 22.9 23.0 18.7 25.5 25.5 24.2 24.3 19.7 25.5 25.5 25.5 25.5 20.7
KW 2.3 2.3 2.3 2.4 2.4 2.3 2.3 2.4 2.4 2.4 2.3 2.3 2.4 2.4 2.4
T.C. 28.3 29.3 29.0 31.9 34.2 29.7 30.0 29.7 32.7 35.0 31.0 30.7 30.4 33.4 35.8
S.C. 25.5 25.2 22.0 22.1 17.9 25.5 25.4 23.3 23.4 18.7 25.5 25.5 24.7 24.7 19.6
KW 2.7 2.7 2.8 2.8 2.8 2.7 2.7 2.8 2.8 2.8 2.7 2.7 2.8 2.8 2.8
T.C. 26.9 27.7 27.3 30.1 32.1 28.2 28.3 27.9 30.8 32.9 29.4 29.0 28.5 31.4 33.6
S.C. 25.5 24.9 21.1 21.3 17.1 25.5 25.2 22.4 22.6 17.8 25.5 25.5 23.8 23.9 18.5
KW 3.1 3.1 3.2 3.1 3.3 3.1 3.1 3.2 3.1 3.3 3.1 3.1 3.3 3.1 3.3
T.C. 25.5 26.0 25.5 28.3 30.1 26.7 26.6 26.0 28.9 30.8 27.8 27.2 26.5 29.5 31.4
S.C. 25.5 24.5 20.1 20.4 16.2 25.5 25.0 21.5 21.7 16.8 25.5 25.5 22.9 23.1 17.4
KW 3.5 3.5 3.6 3.5 3.8 3.5 3.5 3.7 3.5 3.8 3.5 3.4 3.8 3.5 3.7
Johnson Controls Unitary Products 17
413432-YTG-A-0608
Air Handler Coil T.C. S.C. KW
- FC/MC/PC35 0.98 0.98 1.00
- FC/MC/PC36 0.97 0.96 1.00
- FC/MC/PC37 1.00 1.00 1.00
- FC/MC/PC48 1.01 1.01 1.00
- FC/MC/PC60 1.01 1.02 1.00
- FC/MC62 1.01 1.02 1.00
- UC60 0.96 0.95 1.00
- HC36 0.98 0.98 1.00
- HC42 1.00 1.00 1.00
- HD48 1.00 1.00 1.00
AHP36 - 1.00 1.01 0.97
AV36 - 1.03 1.05 0.94
AV/SV48 - 0.98 0.98 0.93
F4FP036 - 0.97 0.97 1.00
F4FP040 - 0.97 0.96 1.00
F4FP042 - 0.97 0.96 1.00
F4FV060 - 0.98 0.98 0.92
F5FP048 - 1.03 1.05 0.93
F5FP060 - 0.99 1.00 0.93
MA12B FC/MC35B 0.98 0.98 1.00
MV12B FC/MC35B 0.99 0.99 0.95
MV16C FC/MC35C 1.00 1.00 0.93
MA12B FC/MC36B 0.97 0.96 1.00
MV12B FC/MC36B 0.99 0.98 0.95
MV16C FC/MC36C 0.99 0.98 0.93
MA12B FC/MC43B 1.00 1.00 1.00
MV12B FC/MC43B 1.01 1.01 0.95
MV16C FC/MC43C 1.02 1.02 0.93
MA14D FC/MC48D 1.01 1.01 1.00
MV12D FC/MC48D 1.02 1.01 0.93
MV16C FC/MC48C 1.03 1.03 0.92
MV20D FC/MC48D 1.03 1.03 0.92
MA14D FC/MC60D 1.01 1.02 1.00
MV12D FC/MC60D 1.02 1.02 0.92
MV20D FC/MC60D 1.03 1.04 0.92
MA14D FC/MC62D 1.01 1.02 1.00
MV12D FC/MC62D 1.02 1.02 0.92
MV20D FC/MC62D 1.04 1.04 0.92
Variable Speed
Furnace
PV8*B16 FC/MC/PC35B 0.99 0.99 0.95
PV8*C16 FC/MC/PC35C 0.99 0.99 0.94
PV8*C20 FC/MC/PC35C 1.00 1.00 0.94
P(C,V)9*B12 FC/MC/PC35B 0.99 0.99 0.97
P(C,V)9*C16 FC/MC/PC35C 0.99 0.99 0.94
P(C,V)9*C20 FC/MC/PC35C 0.99 0.99 0.95
PV8*A12 FC/MC/PC36A 0.98 0.97 0.97
PV8*B16 FC/MC/PC36B 0.99 0.98 0.95
PV8*C16 FC/MC/PC36C 0.99 0.98 0.94
PV8*C20 FC/MC/PC36C 0.99 0.98 0.94
PV9*A12 FC/MC/PC36A 0.98 0.97 0.99
P(C,V)9*B12 FC/MC/PC36B 0.98 0.97 0.96
P(C,V)9*C16 FC/MC/PC36C 0.99 0.98 0.94
P(C,V)9*C20 FC/MC/PC36C 0.99 0.98 0.95
PV8*A12 FC/MC/PC37A 1.00 1.00 0.98
PV9*A12 FC/MC/PC37A 0.99 0.97 0.97
PV8*B16 FC/MC/PC43B 1.01 1.01 0.95
PV8*C16 FC/MC/PC43C 1.02 1.02 0.94
PV8*C20 FC/MC/PC43C 1.02 1.02 0.93
P(C,V)9*B12 FC/MC/PC43B 1.01 1.01 0.97
P(C,V)9*C16 FC/MC/PC43C 1.02 1.02 0.94
P(C,V)9*C20 FC/MC/PC43C 1.01 1.01 0.95
PV8*C16 FC/MC/PC48C 1.03 1.03 0.93
PV8*C20 FC/MC/PC48C 1.03 1.03 0.93
P(C,V)9*C16 FC/MC/PC48C 1.02 1.03 0.94
P(C,V)9*C20 FC/MC/PC48C 1.02 1.03 0.94
P(C,V)9*D20 FC/MC/PC48D 1.02 1.03 0.94
PV8*B16 HC36B 0.99 0.99 0.95
P(C,V)9*B12 HC36B 0.99 0.99 0.96
PV8*C16 HC42C 1.02 1.02 0.94
PV8*C20 HC42C 1.02 1.02 0.93
P(C,V)9*C16 HC42C 1.02 1.02 0.94
P(C,V)9*C20 HC42C 1.01 1.01 0.95
PV8*C16 HD48 1.02 1.02 0.93
PV8*C20 HD48 1.02 1.02 0.93
P(C,V)9*C16 HD48 1.02 1.01 0.94
P(C,V)9*C20 HD48 1.02 1.01 0.94
P(C,V)9*D20 HD48 1.02 1.01 0.94
PV8*C20 FC/MC62D 1.03 1.04 0.93
P(C,V)9*C16 FC/MC62D 1.03 1.03 0.94
P(C,V)9*C20 FC/MC62D 1.03 1.03 0.94
P(C,V)9*D20 FC/MC62D 1.03 1.03 0.94
PV8*C16 UC60C 0.98 0.96 0.93
PV8*C20 UC60C 0.98 0.97 0.93
P(C,V)9*C16 UC60C 0.98 0.96 0.94
P(C,V)9*C20 UC60C 0.98 0.96 0.94
P(C,V)9*D20 UC60D 0.98 0.96 0.94
Coil T.C. S.C. KW
18 Johnson Controls Unitary Products
413432-YTG-A-0608
COOLING PERFORMANCE DATA
AIR CONDITIONER MODEL NO. TCGF42S41S1
INDOOR COIL MODEL NO. FC/MC/PC48
CONDENSING
ENTERING AIR
TEMPERATURE
65
75
85
95
105
115
125
NOTE: ALL CAPACITIES INCLUDE I NDOOR FAN HEAT AT 1250 BTUH/1000 CFM.
Multipliers for determining the performance with other indoor sections.
NOTE: For dry bulb temperatures different than those listed (between 73-87 F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the
listed temperature and decreases by 1060 BTUH per 1000 CFM per degree below the listed temperature.
Air Handler Coil T.C. S.C. KW
- FC/MC/PC42 0.94 0.93 1.00
- FC/MC/PC43 0.99 0.99 1.00
- FC/MC/PC60 1.00 1.00 1.00
- FC/MC62 1.00 1.00 1.00
- HC42 0.99 0.99 1.00
- HD48 1.00 0.98 1.00
- HD60 1.01 1.01 1.00
AV/SV48 - 0.97 0.95 0.94
AV/SV60 - 0.97 0.95 0.94
F4FV060 - 0.97 0.96 0.93
F5FP048 - 1.02 1.04 0.95
F5FP060 - 0.97 0.97 0.95
MA16C FC/MC43C 0.99 0.99 1.00
MV16C FC/MC43C 1.00 1.00 0.95
MA14D FC/MC48D 1.00 1.00 1.00
MA16C FC/MC48C 1.00 1.00 1.00
MV16C FC/MC48C 1.02 1.02 0.95
MV20D FC/MC48D 1.02 1.02 0.94
MA14D FC/MC60D 1.00 1.00 1.00
MA16C FC/MC60C 1.00 1.00 1.00
MV20D FC/MC60D 1.01 1.02 0.93
MA14D FC/MC62D 1.00 1.00 1.00
MV20D FC/MC62D 1.02 1.02 0.93
Variable Speed Furnace Coil T.C. S.C. KW
PV8*B16 FC/MC/PC43B 1.00 0.99 0.97
PV8*C20 FC/MC/PC43C 1.00 1.00 0.96
P(C,V)9*C16 FC/MC/PC43C 1.00 0.99 0.98
P(C,V)9*C20 FC/MC/PC43C 1.00 1.00 0.96
IDCFM 1200 1400 1600
ID DB (°F) 80 80 75 80 80 80 80 75 80 80 80 80 75 80 80
ID WB (°F) 57 62 62 67 72 57 62 62 67 72 57 62 62 67 72
T.C. 40.7 42.7 42.3 45.8 48.7 42.2 43.5 43.1 46.7 49.6 43.8 44.3 43.9 47.5 50.5
S.C. 39.9 36.7 30.9 30.4 23.9 41.5 39.4 33.0 32.5 25.0 43.2 42.0 35.1 34.7 26.1
KW 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9
T.C. 39.3 40.8 40.7 43.9 47.3 40.8 41.7 41.4 44.8 48.0 42.3 42.5 42.2 45.7 48.8
S.C. 38.4 35.6 30.1 29.6 23.2 40.0 38.3 32.2 31.8 24.4 41.7 40.9 34.4 34.1 25.6
KW 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2
T.C. 37.9 38.9 39.1 42.1 45.9 39.3 39.9 39.8 42.9 46.5 40.8 40.8 40.5 43.8 47.0
S.C. 36.8 34.6 29.2 28.9 22.6 38.5 37.2 31.4 31.2 23.9 40.2 39.8 33.7 33.4 25.2
KW 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5
T.C. 36.5 37.0 37.5 40.3 44.5 37.9 38.0 38.2 41.1 44.9 39.3 39.1 38.8 41.9 45.3
S.C. 35.3 33.5 28.3 28.1 21.9 37.0 36.1 30.6 30.5 23.3 38.7 38.7 33.0 32.8 24.7
KW 2.8 2.8 2.8 2.8 2.8 2.8 2.8 2.8 2.8 2.8 2.8 2.8 2.8 2.8 2.8
T.C. 34.7 34.9 35.1 37.8 41.8 36.0 36.0 35.8 38.6 42.2 37.2 37.1 36.4 39.4 42.7
S.C. 33.4 32.4 27.3 27.2 21.1 35.0 34.7 29.6 29.5 22.5 36.6 36.9 31.8 31.8 23.8
KW 3.3 3.3 3.3 3.3 3.2 3.3 3.3 3.3 3.3 3.2 3.3 3.3 3.3 3.3 3.2
T.C. 32.9 32.9 32.9 35.4 39.2 34.1 34.0 33.5 36.1 39.7 35.3 35.1 34.1 36.9 40.1
S.C. 31.7 31.3 26.4 26.3 20.3 33.1 33.2 28.5 28.6 21.7 34.6 35.2 30.6 30.8 23.0
KW 3.8 3.8 3.8 3.7 3.7 3.8 3.8 3.8 3.7 3.7 3.7 3.7 3.8 3.7 3.7
T.C. 31.1 30.8 30.6 33.0 36.6 32.2 32.0 31.2 33.7 37.1 33.3 33.1 31.8 34.4 37.6
S.C. 29.9 30.2 25.5 25.4 19.5 31.3 31.8 27.5 27.7 20.8 32.6 33.4 29.5 29.9 22.1
KW 4.3 4.3 4.3 4.2 4.1 4.3 4.2 4.3 4.1 4.1 4.2 4.2 4.3 4.1 4.1
Variable Speed Furnace Coil T.C. S.C. KW
PV8*C16 FC/MC/PC48C 1.01 1.01 0.97
PV8*C20 FC/MC/PC48C 1.01 1.01 0.96
P(C,V)9*C16 FC/MC/PC48C 1.01 1.01 0.98
P(C,V)9*C20 FC/MC/PC48C 1.01 1.01 0.96
P(C,V)9*D20 FC/MC/PC48D 1.01 1.01 0.95
PV8*C16 FC/MC/PC60C 1.01 1.01 0.96
PV8*C20 FC/MC/PC60C 1.01 1.01 0.96
P(C,V)9*C16 FC/MC/PC60C 1.00 1.01 0.97
P(C,V)9*C20 FC/MC/PC60C 1.01 1.01 0.96
P(C,V)9*D20 FC/MC/PC60D 1.01 1.02 0.95
PV8*C16 HC42C 1.00 1.00 0.97
PV8*C20 HC42C 1.00 1.00 0.96
P(C,V)9*C16 HC42C 1.00 0.99 0.98
P(C,V)9*C20 HC42C 1.00 1.00 0.96
P(C,V)9*D20 HC60D 0.96 0.95 0.94
PV8*C16 HD48 1.01 1.00 0.96
PV8*C20 HD48 1.01 1.00 0.96
P(C,V)9*C16 HD48 1.00 0.99 0.98
P(C,V)9*C20 HD48 1.01 1.00 0.96
P(C,V)9*D20 HD48 1.01 1.00 0.95
PV8*C16 HD60 1.02 1.02 0.96
PV8*C20 HD60 1.02 1.02 0.96
P(C,V)9*C16 HD60 1.02 1.02 0.97
P(C,V)9*C20 HD60 1.02 1.02 0.96
P(C,V)9*D20 HD60 1.03 1.03 0.95
PV8*C20 FC/MC62D 1.01 1.02 0.96
P(C,V)9*C16 FC/MC62D 1.01 1.01 0.97
P(C,V)9*C20 FC/MC62D 1.01 1.01 0.96
P(C,V)9*D20 FC/MC62D 1.02 1.02 0.95
Johnson Controls Unitary Products 19
413432-YTG-A-0608
COOLING PERFORMANCE DATA
AIR CONDITIONER MODEL NO. TCGF48S41S1
INDOOR COIL MODEL NO. FC/MC/PC60
CONDENSING
ENTERING AIR
TEMPERATURE
65
75
85
95
105
115
125
NOTE: ALL CAPACITIES INCLUDE INDOOR FAN HEAT AT 1250 BTUH/1000 CFM.
Multipliers for determining the performance with other indoor sections.
NOTE: For dry bulb temperatures different than those listed (between 73-87 F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the
listed temperature and decreases by 1060 BTUH per 1000 CFM per degree below the listed temperature.
Air Handler Coil T.C. S.C. KW
- FC/MC/PC48 1.00 1.00 1.00
- FC/MC62 1.01 1.00 1.00
- HD48 1.00 1.00 1.00
- HD60 1.02 1.02 1.00
AHP/SHP60 - 0.95 0.94 0.97
AV/SV48 - 0.95 0.94 0.96
AV/SV60 - 0.95 0.94 0.96
F4FV060 - 0.95 0.94 0.96
F5FP048 - 1.01 1.04 0.97
F5FP060 - 0.95 0.95 0.98
MA16C FC/MC48C 1.00 1.00 1.00
MA20D FC/MC48D 1.00 1.00 1.00
MV16C FC/MC48C 1.01 1.01 0.96
MV20D FC/MC48D 1.01 1.01 0.96
MA16C FC/MC60C 1.00 1.00 1.00
MA20D FC/MC60D 1.00 1.00 1.00
MV20D FC/MC60D 1.01 1.01 0.96
MA20D FC/MC62D 1.01 1.00 1.00
MV20D FC/MC62D 1.02 1.01 0.96
IDCFM 1400 1600 1800
ID DB (°F) 80 80 75 80 80 80 80 75 80 80 80 80 75 80 80
ID WB (°F) 57 62 62 67 72 57 62 62 67 72 57 62 62 67 72
T.C. 44.1 45.2 43.0 47.2 47.3 44.2 45.3 43.9 47.4 47.9 44.2 45.3 44.8 47.6 48.5
S.C. 43.7 39.0 33.0 31.2 24.2 44.3 40.6 34.5 32.2 24.8 44.9 42.3 36.0 33.2 25.5
KW 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.3 2.2 2.2 2.2 2.2 2.3
T.C. 42.6 43.5 41.7 45.7 46.9 43.0 43.8 42.5 46.1 47.5 43.5 44.1 43.2 46.5 48.2
S.C. 42.4 39.0 33.0 31.3 24.3 43.3 40.8 34.6 32.6 25.0 44.1 42.6 36.3 33.9 25.7
KW 2.5 2.5 2.5 2.5 2.6 2.5 2.5 2.5 2.5 2.6 2.5 2.5 2.5 2.5 2.6
T.C. 41.0 41.9 40.4 44.1 46.5 41.9 42.4 41.0 44.8 47.2 42.7 42.9 41.6 45.4 47.9
S.C. 41.1 38.9 32.9 31.4 24.3 42.2 40.9 34.7 33.0 25.2 43.4 42.9 36.6 34.6 26.0
KW 2.8 2.8 2.8 2.9 2.9 2.8 2.8 2.8 2.9 2.9 2.8 2.8 2.8 2.9 2.9
T.C. 39.5 40.2 39.1 42.6 46.0 40.7 41.0 39.5 43.5 46.8 42.0 41.8 40.0 44.3 47.6
S.C. 39.8 38.9 32.8 31.5 24.4 41.2 41.1 34.8 33.4 25.3 42.6 43.2 36.9 35.2 26.3
KW 3.1 3.2 3.1 3.2 3.2 3.1 3.2 3.1 3.2 3.2 3.1 3.2 3.1 3.2 3.2
T.C. 37.1 37.6 36.0 39.8 43.4 38.3 38.6 36.6 40.6 44.1 39.5 39.6 37.2 41.4 44.8
S.C. 37.3 36.8 31.4 30.5 23.5 38.6 38.7 33.5 32.5 24.6 40.0 40.5 35.5 34.4 25.7
KW 3.6 3.6 3.6 3.6 3.7 3.6 3.6 3.6 3.6 3.7 3.6 3.6 3.6 3.6 3.7
T.C. 34.9 35.0 33.0 37.1 40.8 36.0 36.3 33.7 37.8 41.5 37.1 37.5 34.4 38.5 42.1
S.C. 34.8 34.8 30.0 29.5 22.7 36.2 36.4 32.1 31.6 24.0 37.5 37.9 34.2 33.6 25.2
KW 4.0 4.0 4.0 4.0 4.1 4.0 4.0 4.0 4.0 4.1 4.0 4.0 4.0 4.1 4.1
T.C. 32.6 32.5 30.1 34.4 38.2 33.6 33.9 30.8 35.0 38.8 34.6 35.4 31.6 35.7 39.5
S.C. 32.4 32.9 28.7 28.4 21.9 33.7 34.1 30.8 30.6 23.3 34.9 35.3 32.9 32.9 24.6
KW 4.4 4.4 4.4 4.5 4.6 4.4 4.4 4.4 4.5 4.6 4.5 4.5 4.4 4.5 4.6
Variable Speed
Furnace
PV8*C16 FC/MC/PC48C 0.99 0.97 0.98
PV8*C20 FC/MC/PC48C 1.00 1.00 0.99
P(C,V)9*C16 FC/MC/PC48C 1.00 1.00 1.00
P(C,V)9*C20 FC/MC/PC48C 1.00 1.01 0.98
PV8*C16 FC/MC/PC60C 0.99 0.98 0.98
PV8*C20 FC/MC/PC60C 1.01 1.01 0.98
P(C,V)9*C16 FC/MC/PC60C 1.00 1.00 1.00
P(C,V)9*C20 FC/MC/PC60C 1.00 1.00 0.98
P(C,V)9*D20 FC/MC/PC60D 1.01 1.01 0.97
PV8*C16 HD48 0.99 0.97 0.98
PV8*C20 HD48 1.00 1.00 0.98
P(C,V)9*C16 HD48 1.00 1.00 1.00
P(C,V)9*C20 HD48 1.00 1.00 0.98
P(C,V)9*D20 HD48 1.01 1.00 0.97
PV8*C16 HD60 1.01 0.99 0.98
PV8*C20 HD60 1.02 1.02 0.98
P(C,V)9*C16 HD60 1.02 1.02 1.00
P(C,V)9*C20 HD60 1.02 1.02 0.98
P(C,V)9*D20 HD60 1.02 1.03 0.97
PV8*C20 FC/MC62D 1.01 1.01 0.98
P(C,V)9*C16 FC/MC62D 1.01 1.00 1.00
P(C,V)9*C20 FC/MC62D 1.01 1.01 0.98
P(C,V)9*D20 FC/MC62D 1.01 1.01 0.97
Coil T.C. S.C. KW
20 Johnson Controls Unitary Products
413432-YTG-A-0608
COOLING PERFORMANCE DATA
AIR CONDITIONER MODEL NO. TCGF60S41S1
INDOOR COIL MODEL NO. FC/MC/PC62
CONDENSING
ENTERING AIR
TEMPERATURE
65
75
85
95
105
115
125
NOTE: ALL CAPACITIES INCLUDE I NDOOR FAN HEAT AT 1250 BTUH/1000 CFM.
Multipliers for determining the performance with other indoor sections.
NOTE: For dry bulb temperatures different than those listed (between 73-87 F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the
listed temperature and decreases by 1060 BTUH per 1000 CFM per degree below the listed temperature.
Air Handler Coil T.C. S.C. KW
- FC/MC/PC60 0.96 0.98 1.00
- HC60 0.96 0.98 1.00
AV/SV60 - 0.97 0.99 0.97
MV20D FC/MC60D 0.97 0.99 0.98
MA20D FC/MC62D 1.00 1.00 1.00
MV20D FC/MC62D 1.01 1.01 0.98
IDCFM 1400 1600 1800
ID DB (°F) 80 80 75 80 80 80 80 75 80 80 80 80 75 80 80
ID WB (°F) 57 62 62 67 72 57 62 62 67 72 57 62 62 67 72
T.C. 54.5 57.8 56.7 62.8 68.7 55.3 59.1 58.5 64.7 69.7 56.1 60.4 60.2 66.6 70.7
S.C. 54.0 49.2 40.9 40.7 32.5 56.2 52.4 43.1 42.9 34.1 58.5 55.7 45.3 45.1 35.8
KW 2.7 2.7 2.6 2.7 2.6 2.7 2.7 2.7 2.7 2.7 2.7 2.7 2.7 2.7 2.7
T.C. 52.7 55.6 54.4 60.5 66.0 54.8 56.8 56.1 62.1 66.9 56.9 58.0 57.7 63.7 67.9
S.C. 52.3 48.1 39.9 39.8 31.5 54.3 51.1 42.2 41.9 33.1 56.4 54.2 44.4 44.1 34.7
KW 3.1 3.1 3.1 3.1 3.1 3.1 3.1 3.1 3.1 3.1 3.1 3.1 3.1 3.1 3.1
T.C. 50.8 53.5 52.2 58.1 63.3 54.3 54.5 53.7 59.5 64.2 57.7 55.6 55.2 60.8 65.1
S.C. 50.6 47.1 38.9 38.9 30.5 52.4 49.9 41.2 41.0 32.1 54.3 52.7 43.6 43.0 33.6
KW 3.5 3.6 3.5 3.5 3.5 3.5 3.6 3.5 3.5 3.5 3.5 3.6 3.5 3.5 3.5
T.C. 49.0 51.4 50.0 55.8 60.5 53.7 52.3 51.3 56.8 61.4 58.4 53.2 52.6 57.9 62.3
S.C. 48.9 46.0 37.9 38.1 29.5 50.5 48.6 40.3 40.0 31.0 52.2 51.2 42.7 41.9 32.6
KW 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0
T.C. 46.4 48.2 46.9 52.5 57.0 50.0 49.3 48.1 53.3 58.0 53.7 50.4 49.3 54.2 59.0
S.C. 46.5 44.6 36.7 36.5 28.1 48.0 47.0 39.0 38.5 29.6 49.5 49.3 41.2 40.5 31.1
KW 4.8 4.8 4.8 4.7 4.7 4.8 4.8 4.8 4.7 4.7 4.7 4.8 4.8 4.7 4.7
T.C. 43.8 45.2 43.9 49.3 53.6 46.5 46.4 45.0 50.0 54.7 49.1 47.6 46.1 50.7 55.9
S.C. 44.1 43.3 35.5 35.0 26.8 45.5 45.4 37.6 37.1 28.3 46.9 47.5 39.8 39.2 29.7
KW 5.6 5.6 5.7 5.4 5.4 5.5 5.5 5.6 5.4 5.3 5.5 5.5 5.5 5.4 5.3
T.C. 41.3 42.2 40.8 46.0 50.2 42.9 43.5 41.9 46.6 51.5 44.5 44.9 42.9 47.2 52.7
S.C. 41.8 41.9 34.3 33.5 25.5 43.1 43.8 36.3 35.7 26.9 44.4 45.6 38.3 37.8 28.3
KW 6.4 6.4 6.5 6.1 6.0 6.3 6.3 6.4 6.1 6.0 6.2 6.2 6.3 6.1 6.0
Variable Speed
Furnace
P(C,V)9*D20 HC60D 0.95 0.93 0.97
PV8*C20 HD60 0.99 0.99 0.99
P(C,V)9*C20 HD60 0.99 0.99 0.98
P(C,V)9*D20 HD60 0.98 0.97 0.97
PV8*C20 FC/MC62D 1.00 1.00 0.99
P(C,V)9*C20 FC/MC62D 0.98 0.97 0.98
P(C,V)9*D20 FC/MC62D 0.99 0.96 0.97
Coil T.C. S.C. KW
Johnson Controls Unitary Products 21
NOTES
Subject to change without notice. Printed in U.S.A. 413432-YTG-A-0608
Copyright © 2008 by Johnson Controls, Inc. All rights reserved. Supersedes: Nothing
Johnson Controls Unitary Products
5005 York Drive
Norman, OK 73069
Loading...