Multi-Pure
®
Water Guardian Drinking Water Appliance
For Countertop Use
M
ODEL NO. MPADC
Owner’s Manual
I. Operation & Maintenance Specifications........................................................................................................2
II. Installation instructions - Inspect the housing...............................................................................................3
III. Installation instructions - Connect the hose to the housing.........................................................................4
IV. Installation instructions - Connect the diverter valve to your faucet.........................................................4-5
V. Start-up and use of your Water Guardian System...........................................................................................5
VI. Filter Life..............................................................................................................................................................6
VII. Instructions for Replacing Your Filter .............................................................................................................6-7
VIII. Product Warranty ............................................................................................................................................. 8
IX. Product Certification ......................................................................................................................................... 8
X. Performance Data Sheet..................................................................................................................................9-11
XI. California Certification.......................................................................................................................................12
XII. Troubleshooting.................................................................................................................................................12
XIII. Questions and Answers.....................................................................................................................................13
Table of Contents
2
Water Guardian Model
Model Numbers MPADC
Housing Composition Polypropylene
Rubber Items Nitrile
Inlet 3/8" stem
Outlet 1/4" stem
Replacement Filter Type CBTAD
Approximate Filter Capacity 750 gallons
Approximate Flow Rate @ 60 psi 0.75 gpm
Maximum Working Pressure 100 psi/7.0 kg/cm2
Minimum Working Pressure 30 psi/2.1 kg/cm2
Maximum Operating Temperature 100F / 38C - for cold water use
Minimum Operating Temperature 32F / 0C
Particle Retention Size 0.5 micron (sub micron)
Certified by: NSF
I. Operation and Maintenance Specifications
Multi-Pure Drinking Water Systems
Thank you for selecting a Multi-Pure Drinking Water System to meet your need for quality drinking water. You have
acquired one of the finest drinking water treatment devices available for the reduction of a wide array of contaminants.
We are confident that your Multi-Pure System will make a difference in your life. Thank you for your business.
INSTALLATION, OPERATION & MAINTENANCE MANUAL
Multi-Pure
Water Guardian Drinking Water
Appliance
The Multi-Pure Water Guardian Drinking Water Appliance, Model
MPADC is designed for use on the countertop next to your sink.
You can connect it to your existing faucet using the high-tech
chrome diverter valve that allows you to easily switch from filtered
to unfiltered water.
NOTE: The filter cartridge is factory-installed inside the unit housing.
Step 1 Determine a desired location on your countertop for the
unit so that the hose can easily be attached to your
faucet.
Step 2 Inspect the unit housing to confirm that the housing top
is securely connected to the bottom. If necessary,
use the hand tool, shipped with the unit, to tighten the
top.
a. With the housing in an upright position, slide the hand
tool over the top so that the ridges on the tool fit into
the grooves on the housing top.
b. Applying steady pressure, turn clockwise to tighten.
Hold the base in place on the countertop while turning
the top.
c. Tighten sufficiently so that the o-ring at the bottom of
the top is not visible. DO NOT OVER TIGHTEN.
housing top
hand tool
housing
base
turn to close
II. Inspect the Housing
3
NOTE: The Water Guardian Drinking Water Appliance is easy to install on most standard faucets.
And, it includes a feature that makes it easy to switch from filtered to unfiltered water.
Step 4 Remove the aerator or screen from the end of your faucet. The water at your sink should
be turned off.
Step 5 Attach the Diverter Valve directly to the faucet spout. If the threads of the Diverter Valve
don't match the threads of your faucet, use one of the adapters provided with your unit.
a. Faucets with Outside Threads: For most faucets with outside threads, the diverter
valve can be attached directly to the faucet. However, if the Diverter Valve is smaller
than your faucet, attach the adapter with inside threads directly to your faucet and then
attach the Diverter Valve to the adapter.
b. Faucets with Inside Threads: If your faucet has threads on the inside, attach one of the two adapters with out-
side threads (choose the appropriate size for your faucet) directly to your faucet and then attach the Diverter
Valve to the adapter.
c. Faucets with No Threads: If your faucet has no threads, you will need to contact your independent dealer.
d. Faucets with Odd Sized Threads: If your faucet does not fit any of the adapters provided with your unit, please
contact your independent dealer.
e. Faucets requiring more clearance for the connection, such as sprayer hose faucets, would use a long adapter
(MC257). See Step 5.e. on next page for installation instructions.
Existing
Faucet
Diverter Valve Attachment
Diverter Valve Attachment
with adapter
Adapters (choose one)
Many installations do not
require an adapter
IV. Connect the Diverter Valve to Your Faucet
Unfiltered
(tap) Water
Spout
Filtered
Water Spout
4
NOTE: The Water Guardian comes with a diverter valve and hose that connects the
drinking water system to your faucet.
Step 3 To connect the hose to the housing base, insert the tubing on the end of the
hose into the inlet and outlet ports.
a. Insert the larger hose into the bottom port (Inlet connector) by slowly
pushing the stem straight into the connector as far as it will go. Give a
second push to confirm that the stem is fully inserted.
b. Insert the smaller hose into the top port (Outlet connector) by slowly
pushing the stem straight into the connector as far as it will go. Give a
second push to confirm that the stem is fully inserted.
III. Connect the Hose to the Housing
Small hose
Outlet
Inlet
Large hose
bypass
lever
Diverter Valve
Swivel
Attachment
Ring
MC108
MC107
MC106
MC257
Congratulations, your Multi-Pure Water Guardian Drinking Water Appliance has been connected to your faucet and you are
now ready to start-up the unit, as follows:
Step 6 Using a paper towel or cloth, dry off all connections. Also, dry off the drinking water unit.
Step 7 Ensure that all connections are tight (CAUTION: DO NOT OVER TIGHTEN).
Step 8 Before starting the flushing and start-up process, unscrew and remove the aerator
(screen) from the filtered water spout. Rinse out the aerator to remove any debris that
may have collected on the two screens inside it. You will reconnect the aerator upon
completion of the filter flushing process.
Step 9 To purge all air from the unit, turn the housing up
side down and then turn on the water.
Push the bypass lever of the diverter to start the flow of water through the unit. Allow
the water to run through the unit and filtered water spout for one minute. Then close
the bypass lever and shut off the water at the faucet.
Step 10 Turn the unit right side up and place it on your counter and check all connections to
confirm that there are no leaks.
.
Step 11 Turn on the water and push the bypass lever of the diverter valve to again start the flow
of water through the unit.
Step 12 Allow water to run through the unit to waste for approximately 25 minutes to fully flush
the filter and charge the carbon.
Step 13 Push the bypass lever inward to shutoff the flow of water through the Aqua Dome
System. Then shut off the water at your faucet and check for leaks.
Step 14 Lastly, reconnect the aerator to the filtered water spout.
Congratulations, you have completed the installation.
If you have any questions regarding the installation of your
countertop unit, call:
Please call your authorized independent dealer
V. Start-up and Use of Your Countertop Drinking Water System
bypass
lever
Turn Unit upside
down to assure
that all air escapes
from the housing
unfiltered
water
filtered
water
aerator
5
IV. Connect the Diverter Valve to Your Faucet (continued)
Fig. 2
Fig. 1
Step 5.e Instructions for Installing a Long Adapter
The long adapter (MC257) shown in Fig. 1 is used to connect the Hose & Diverter Valve assembly to
your faucet or sprayer hose faucet, needing more clearance for the connection.
1. Remove the aerator or screen from your faucet.
2. Take the long adapter and attach it to the opening of the spout/sprayer then connect the Hose &
Diverter Valve assembly to the adapter (Fig. 2).
3. Position the Drinking Water System on the sink to allow enough room to use the sprayer faucet.
VII. Instructions for Changing Your Filter
REMOVING THE OLD FILTER
1. Remove the shipping materials - plastic wrapper and instruction wrapper.
2. It may be advisable to place a folded towel beneath the housing before
opening it. Or you may place it in your sink or in a pan to open.
3. Confirm that your tap water is off.
4. Open the diverter valve by pushing the bypass lever (Fig. A) so that the
water flows through the unit and the filtered water spout until the flow
stops.
5. When the flow of water stops, then close the diverter by pushing the
bypass valve.
6. With the housing in an upright position, or on its side on a towel, use the
Water Guardian hand tool to open the unit (Fig. B).
a. Slide the hand tool over the housing top so that the ridges on the tool
fit into the grooves on the housing top.
b. Hold the base in place on the countertop and apply steady pressure to
the hand tool to turn the top.
c. Once the top is loose, you can complete the opening process by turn-
ing it with your hand.
7. Remove the housing top from the base (Fig C).
8. Remove the old filter (cartridge) from the unit base by pulling out and slightly twisting the filter until it is released from the base as shown in Fig. D.
Make sure black gasket remains on bottom of housing base.
9. Wrap the used filter in paper and dispose of it in your normal refuse.
10. Clean and rinse out the inside of the housing.
INSTALLING THE NEW FILTER
11. Insert the new filter in the center port of the housing base, twisting slightly,
as shown in Fig. D. Then push straight down on the filter to assure that is
firmly in place.
12. Reconnect the housing top with base (Fig. C).
13. Hand-tighten the housing top by turning it clockwise. The top should be
securely connected to the base so the o-ring at the bottom of the top is not
visible. If necessary, use the hand tool, shipped with your unit, to tighten
the top (Fig. B-1).
a. With the housing in an upright position, slide the hand tool over the top
so that the ridges on the tool fit into the grooves on the housing top.
b. Applying steady pressure, turn clockwise to tighten. Hold the base in
place on the countertop while turning the top.
c. Tighten sufficiently so that the o-ring on the top threads is not visible.
DO NOT OVER TIGHTEN.
6
Fig. A
Fig.B-2Fig.B-1
Fig. C
Fig. D
bypass
lever
VI. Filter Life
Filter life will vary in proportion to the amount of water used and the level of impurities in the water being processed.
Claims of capacity are not applicable to contaminants reduced by mechanical filtration because of broad variations in the
quality and quantity of physical matter in your drinking water. Your Multi-Pure filter will clog, protecting you from these
contaminants, and your flow rate diminishes. For contaminants reduced by adsorption, filter life/capacity is 750 gallons.
It is recommended that filters be replaced annually or sooner if needed. For optimum performance and to maintain your
warranty, it is essential that the filter be replaced on a regularly scheduled basis as follows: (a) annually; (b) when the
unit's rated capacity (750 gallons) is reached; (c) the flow rate diminishes; (d) the filter becomes saturated with bad
tastes and odors.
RE-STARTING YOUR WATER GUARDIAN UNIT
14. Using a paper towel or cloth, dry off all connections and your drinking water
unit.
15. Ensure that all connections are tight (CAUTION: DO NOT OVER TIGHTEN
- see item #13c).
16. Before starting the flushing and start-up process, unscrew and remove the
aerator (screen) from the filtered water spout (Fig. F). Rinse out the aerator to remove any debris that may have collected on the two screens inside
it. You will reconnect the aerator upon completion of the filter flushing
process (see step #24).
17. To purge all air from the unit, turn the housing upside down and then turn
on the water at your tap faucet (Fig. G).
18. With the unit upside down, push the bypass lever of the diverter to start the
flow of water through the unit (Fig. H). Allow the water to run through the
unit and filtered water spout (without the aerator) for ONE minute. Then
close the bypass lever and shut off the water at the faucet.
19. Turn the unit right side up, place it on your counter and check all connections to confirm that there are no leaks (Fig. I).
20. Turn on the water and push the bypass lever of the diverter valve to again
start the flow of water through the unit (Fig. H).
21. Allow water to run through the unit to waste for approximately 25 minutes to
fully flush the filter and charge the carbon (Fig H).
22. Push the bypass lever inward to shutoff the flow of water through the Aqua
Dome unit.
23. Shut off the water at your faucet and check for leaks.
24. Then reconnect the aerator to the filtered water spout (Fig. F).
You now can resume using your Multi-Pure Drinking Water System
for all your drinking water, cooking, and food preparation needs.
7
Fig. F
Fig. G
Fig. H
Fig. I
Fig. J
Filtered Water
Aerator
Flush
without
filtered
water
aerator
Date of Installation:________________________________________
Fecha de Instalación
Unit Model Number:_______________________________________
Tipo de Unidad
Filter Type:______________________________________________
Tipo de Filtro
Dates of Filter Change / Fechas de Cambio del Filtro
Multi-Pure Drinking Water Systems
Product Performance Tested and Certified
Multi-Pure Drinking Water Systems have been tested and certified by NSF International to comply with NSF/ANSI Standards 42
and 53 for the reduction of specific contaminants being considered as established or potential health hazards.
Standard 42, Aesthetic Effects
System tested and certified by NSF
International against NSF/ANSI
Standard 42 for the reduction of:
Chloramine
Chlorine taste and odor
Nominal Particulate
reduction, class I
Standard 53, Health Effects
System tested and certified by NSF
International against NSF/ANSI
Standard 53 for the reduction of:
Asbestos Chlordane
Cyst Lead
Mercury MTBE
PCB Toxaphene
Turbidity VOC (listed below)
Disinfection By-Products
chloropicrin
haloacetonitriles (HAN):
bromochloroacetonitrile
dibromoacetonitrile
dichloroacetonitrile
trichloroacetonitrile
haloketones (HK):
1,1-dichloro-2-Propanone
1,1-trichloro-2-Propanone
trihalomethanes (THMs;
TTHMs):
bromodichloromethane
bromoform
chloroform
dibromochloromethane
tribromoacetic acid
Chemicals
benzene
carbon tetrachloride
chlorobenzene
1,2-dichloroethane
1,1-dichloroethylene
cis-1,2-dichloroethylene
1,2-dichloropropane
cis-1,3-dichloropropylene
ethylbenzene
hexachlorobutadiene
hexachlorocyclopentadiene
simazine
styrene
1,1,2,2-tetrachloroethane
tetrachloroethylene
toluene
trans-1,2-dichloroethylene
1,2,4-trichlorobenzene
1,1,1-trichloroethane
1,1,2-trichloroethane
trichloroethylene
xylenes (total)
Herbicides
alachlor
atrazine
2,4-D
dinoseb
pentachlorophenol
2,4,5-TP (silvex)
Pesticides
carbofuran
dibromochloropropane
(DBCP)
o-dichlorobenzene
p-dichlorobenzene
endrin
ethylene dibromide (EDB)
heptachlor
heptachlor epoxide
lindane
methoxychlor
Volatile Organic Chemicals (VOC) includes:
8
Filter capacity is
750 gallons, which is
approximately a 12 month supply
depending on local water conditions.
Claims of capacity are not applicable to contami-
nants reduced by mechanical filtration because of
broad variations in the quality and quantity of
physical matter in your drinking water.
IX. Certification
VIII. Warranty
Multi-Pure Warranty: Multi-Pure
Corporation warrants to the original
retail customer its Drinking Water
Systems and components to be free of
defects in material and workmanship
for use under normal care, and will
repair or replace any System at no
charge (excluding transportation to
Multi-Pure headquarters) to the customer during the warranty period. The
Aqua Dome Housing is warranted for
a period of five (5) years; all exterior
hoses and attachments to the System
are warranted for defects in material
and workmanship for one year.
Multi-Pure Solid Carbon Block Filters
are warranted for defects in material
and workmanship for use under normal care. The capacity of the filter
cartridge depends upon the amount of
impurities in the water to be
processed. For optimum performance, it is essential that the Solid
Carbon Block Filter cartridge be
replaced annually or when it has
processed its listed capacity, whichever comes first.
Except as otherwise expressly provided above, Multi-Pure Corporation
makes no warranties, express or
implied, arising by law or otherwise,
including without limitation the implied
warranties of merchantability and fitness for a particular purpose, to any
person. This limited warranty may not
be altered, varied or extended except
by a written instrument executed by
Multi-Pure Corporation. The remedy
of repair or replacement as provided
under this limited warranty is exclusive. In no event shall Multi-Pure
Corporation be liable for any consequential or incidental damages to any
person whether occasioned by negligence of the manufacturer, including
without limitation damages of loss of
use, cost of substitution, property
damage, or other monetary loss.
Warranty is valid only if Drinking Water
System is operated within conditions
listed herein.
Performance Data Sheet
Multi-Pure Drinking Water Systems have been tested and certified under NSF/ANSI Standard Nos. 53 as
shown below. The concentration of the indicated substances in water entering the system was reduced to a
concentration less than or equal to the permissible limit for water leaving the system, as specified in
NSF/ANSI 53, Health Effects.
Substance
Percent
Reduction**
Influent challenge
concentration
(mg/L unless specified)
Maximum permissible
product water
concentration
(mg/L unless specified)
ALACHLOR*
>98%
0.05 0.001
ASBESTOS >99.9%
107 to 108 fibers/L; fibers
greater than 10
micrometers in length
99% reduction
requirement
ATRAZINE*
>97%
0.1 0.003
BENZENE*
>99%
0.081 0.001
BROMODICHLOROM ETHANE (TTHM)*
>99.8%
0.300 +/- 0.30 0.015
BROMOFORM (TTHM)*
>99.8%
0.300 +/- 0.30 0.015
CARBOFURAN (Furadan)*
>99%
0.19 0.001
CARBON TETRACHLORIDE*
98%
0.078 0.0018
CHLORDANE
>99.5%
0.04 +/-10% 0.002
CHLOROBENZENE (Monochlorobenzene)*
>99%
0.077 0.001
CHLOROPICRIN*
99%
0.015 0.0002
CHLOROFORM (TTHM)* (surrogate chemical)
>99.8%
0.300 +/- 0.30 0.015
Cryptosporidium (CYST)
99.95%
minimum 50,000/mL 99.95%
CYST (Giardia; Cryptosporidium; Entamoeba;
Toxoplasma)
99.95% minimum 50,000/mL 99.95%
2, 4-D*
98%
0.110 0.0017
DBCP (see Dibromochloropropane)*
>99%
0.052 0.00002
1,2-DCA (see 1,2-DICHLOROETHANE)*
95%
0.088 0.0048
1,1-DCE (see 1,1-DICHLOROETHYLENE)*
>99%
0.083 0.001
DIBROMOCHLOROM ETHANE (TTHM;
Chlorodibromomethane)*
>99.8% 0.300 +/- 0.30 0.015
DIBROMOCHLOROP ROPANE (DBCP)*
>99%
0.052 0.00002
o-DICHLOROBENZENE (1,2 Dichlorobenzene)*
>99%
0.08 0.001
p-DICHLOROBENZENE (para-Dichlorobenzene)*
>98%
0.04 0.001
1,2-DICHLOROETHANE (1,2-DCA)*
95%
0.088 0.0048
1,1-DICHLOROETHYLENE (1,1-DCE)*
>99%
0.083 0.001
CIS-1,2-DICHLOROETHYLENE*
>99%
0.17 0.0005
TRANS-1,2- DICHLOROETHYLENE*
>99%
0.086 0.001
1,2-DICHLOROP ROPANE (Propylene Dichloride)*
>99%
0.08 0.001
CIS-1,3- DICHLOROPROPYLENE*
>99%
0.079 0.001
DINOSEB*
99%
0.17 0.0002
EDB (see ETHYLENE DIBROMIDE)*
>99%
0.044 0.00002
ENDRIN*
99%
0.053 0.00059
Entamoeba (see CYSTS)
99.95%
minimum 50,000/mL 99.95%
ETHYLBENZENE*
>99%
0.088 0.001
ETHYLENE DIBROMIDE (EDB)*
>99%
0.044 0.00002
Furadan (see CARBOFURAN)*
>99%
0.19 0.001
**Percent reduction reflects actual performance of Multi-Pure product as specifically tested (at 200% of capacity, i.e.
1500 gallons). Percent reduction shown for VOCs* reflects the allowable claims for Volatile Organic
Chemicals/Compounds as per Tables. Chloroform was used as a surrogate for VOC reduction claims: the Multi-Pure
Systems’ actual reduction rate of Chloroform was >99.8% as tested (at 200% of capacity).
9
X.
For Model No. MPADC
Substance
Percent
Reduction**
Influent challenge
concentration
(mg/L unless specified)
Maximum permissible
product water
concentration
(mg/L unless specified)
Giardia Lamblia (see CYST)
>99.95%
minimum 50,000/mL 99.95%
HALOACETONITRILES ( HAN)*
BROMOCHLOROACETONITRILE
98%
0.022 0.0005
DIBROMOACETONITRILE
98%
0.024 0.0006
DICHLOROACETONITRILE
98%
0.0096 0.0002
TRICHLOROACETONITRILE
98%
0.015 0.0003
HALOKETONES (HK):*
1,1-DICHLORO-2-PROPANONE
99%
0.0072 0.0001
1,1,1-TRICHLORO-2-PROPANONE
96%
0.0082 0.0003
HEPTACHLOR*
>99%
0.25 0.00001
HEPTACHLOR EPOXIDE*
98%
0.0107 0.0002
HEXACHLOROBUTADIENE (Perchlorobutadiene)*
>98%
0.044 0.001
HEXACHLOROCYCLOPENTADIENE*
>99%
0.060 0.000002
LEAD (pH 6.5)
>99.3%
0.15 +/- 10% 0.010
LEAD (pH 8.5)
>99.3%
0.15 +/- 10% 0.010
LINDANE*
>99%
0.055 0.00001
MERCURY (pH 6.5)
>99%
0.006 +/- 10% 0.002
MERCURY (pH 8.5)
>99%
0.006 +/- 10% 0.002
METHOXYCHLOR*
>99%
0.050 0.0001
Methylbenzene (see TOLUENE)*
>99%
0.078 0.001
Monochlorobenzene (see CHLOROBENZENE)*
>99%
0.077 0.001
MTBE (methyl tert-butyl ether)
>96.6%
0.015 +/- 20% 0.005
POLYCHLORINATED BIPHENYLS (PCBs , Aroclor 1260)
>99.9%
0.01 +/- 10% 0.0005
PCE (see TETRACHLOROETHYLENE)*
>99%
0.081 0.001
PENTACHLOROPHENOL*
>99%
0.096 0.001
Perchlorobutadiene (see HEXACHLOROBUTADIENE)*
>98%
0.044 0.001
Propylene Dichloride (see 1,2 -DICHLOROPROPANE)*
>99%
0.080 0.001
SIMAZINE*
>97%
0.120 0.004
Silvex (see 2,4,5-TP)*
99%
0.270 0.0016
STYRENE (Vinylbenzene)*
>99%
0.15 0.0005
1,1,1-TCA (see 1,1,1 - TRICHLOROETHANE)*
95%
0.084 0.0046
TCE (se e TRICHLOROETHYLENE)*
>99%
0.180 0.0010
1,1,2 ,2- TETRACHLOROETHANE*
>99%
0.081 0.001
TETRACHLOROETHYLENE*
>99%
0.081 0.001
TOLUENE (Methylbenzene)*
>99%
0.078 0.001
TOXAPHENE
>92.9%
0.015 +/- 10% 0.003
Toxoplasma (see CYSTS)
99.95%
minimum 50,000/mL 99.95%
2,4,5-TP (Silvex)*
99%
0.270 0.0016
TRIBROMOACETIC ACID* 0.042 0.001
1,2,4 TRICHLOROBENZENE (Unsymtrichlorobenzene)*
>99%
0.160 0.0005
1,1,1 -TRICHLOROETHANE (1,1,1-TCA)*
95%
0.084 0.0046
1,1,2 -TRICHLOROETHANE*
>99%
0.150 0.0005
TRICHLOROETHYLENE (TCE)*
>99%
0.180 0.0010
TRIHALOMETHANES (TTHM) (Chloroform; Bromoform;
Bromodichloromethane; Dibromochloromethane)
>99.8% 0.300 +/- 0.30 0.015
TURBIDITY
>99%
11 +/- 1 NTU 0.5 NTU
y (
TRICHLOROBENZENE)*
>99%
0.160 0.0005
Vinylbenzene (see STYRENE)*
>99%
0.150 0.0005
XYLENES (TOTAL)*
>99%
0.070 0.001
10
N
OTES:
1. Multi-Pure Drinking Water Systems have been certified, as indicated, by NSF International for compliance to NSF/ANSI Standard Nos. 42 & 53.
2. The Multi-Pure Drinking Water Systems have been certified by the State of California Department of Health Services for the reduction of specific
contaminants listed herein.
3. Chloroform was used as a surrogate for claims of reduction of VOCs. Multi-Pure Systems tested at >99.8% actual reduction of Chloroform. Percent
reduction shown herein reflects the allowable claims for VOCs as per tables in the Standard.
4. Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.
Systems certified for cyst reduction may be used on disinfected water that may contain filterable cysts.
5. Filter life will vary in proportion to the amount of water used and the level of impurities in the water being processed. For optimum performance, it is
essential that the filter be replaced on a regularly scheduled basis as follows: (a) annually; (b) when the unit’s rated capacity has been reached; (c)
the flow rate diminishes; (d) the filter becomes saturated with bad tastes and odors.
6. Multi-Pure’s Aqua Dome Housing is warranted for a period of 5 years. All exterior hoses and attachments to the System are warranted for one year.
Please see the Owner’s Manual for complete product guarantee and warranty information.
7. Please see the Owner’s Manual for installation instructions and operating procedures.
8. In compliance with New York law, it is recommended that before purchasing a water treatment system, NY residents have their water supply tested
to determine their actual water treatment needs. Please compare the capabilities of the Multi-Pure unit with your actual water treatment needs.
9. Check for compliance with state and local laws and regulations.
10. While testing was performed under standard laboratory conditions, actual performance may vary.
11. The list of substances which the treatment device reduces does not necessarily mean that these substances are present in your tap water.
Operational Specifications MPADC
Approximate Servic e Capacity (5) 750 gallons
Replacement Filter Type Model No. CBTAD
Approximate Flow Rate @ 60 psi
0.75 gpm
Maximum Water Pressure
100 psi/7.0 kg/cm2
Minimum Water Pressure
30 psi/2.1 kg/cm2
Maximum Operating Temperature
100°F/38°C
for cold water use only
Minimum Operating Temperature 32°F/0°C
Warranty on Housing
5 years
Note: This addresses the U.S. Environmental Protection Agency (EPA) Primary and Secondary Drinking Water Regulations in effect at its time of publication, they relate to Multi-Pure’s performance in conformance to the industry performance criteria. These regulations are continually being updated at the
Federal level. Accordingly, this list of MCLs will be reviewed and amended when appropriate. Please see sales brochure for list of product certifications.
11
Model Nos: MPADC
Substance
Percent
Reduction**
Influent challenge
concentration
(mg/L unless specified)
Maximum permissible
product water
concentration
(mg/L unless specified)
CHLORAMINE as Aesthetic Effect (As
Monochloramine)
>97% 3.0 mg/L +/- 10% 0.5 mg/L
CHLORINE as Aesthetic Effect
99%
2.0 Mg/L +/- 10% > or = 50%
PARTICULATE, (Nominal Particulate Reduction, Class
I, Particles 0.5 TO <1 UM
Class I > 99% At Least 10,000 particles/m L > or = 85%
NSF/ANSI 42 - Aesthetic Effects
The System has been tested according to NSF/ANSI Standard 42 for the reduction of the following substances. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to
the permissible limit for water leaving the system.
California Certification
12
XI.
Problem Cause Remedy
Taste/Odor (general)
The carbon block f ilter may become saturated w ith
the taste and odors it adsorbs.
Change the filter
Rotten egg odor
Typically a sign of H2S (hydr ogen sulfide) gas
w hich can occ ur at any time.
It is recommended that y ou keep two filter cartr idges
on hand. When one becomes saturated w ith odor,
remove it and allow it to dry upside (threaded-hole)
dow n on a paper tow el. The sulfur gas w ill dissipate,
allow ing the cartridge to be reused. Rotating
cartr idges in this manner w ill, in some cas es, help
extend the life of the filter.
Odor & odd color on car tridge
H2S (hydrogen sulf ide) c aused by iron
(orange/br ownish) , manganese (blac kish), and/or
decaying organisms (s limy/blotchy colors) can
cause rotten egg-type odor.
Change of f ilter cartridge is the only recommended
cours e of action.
“Milky” color in w ater
Higher than normal w ater press ure through the
System w ill create small bubbles. Air bubbles do
not effect the performance of the system. Air can
be trapped inside the lid of the hous ing.
For a countertop ins tallation, turn on the w ater and
engage the diverter valve w hile reduc ing the w ater
flow slightly. For a below the sink installation, adjust
the w ater press ure at the feedw ater adapter below
the sink. Turn on the ledge fauc et or diverter v alve
and let w ater run for 3 to 5 minutes af ter installation or
filter c hange.
Flow r ate is s low
Solids: The filter is designed to bec ome r estricted
in its flow rate w hen the filter becomes clogged
w ith particulate and other contaminants. When
your w ater f low rate slow s to the point that it is
inconvenient to us e, it is time to change your filter.
It is recommended that f ilters be replaced at least
every tw elve months or when its c apacity is reac hed,
w hichev er comes f irs t. If w ater pressure is too low ,
adjust w ater press ure to 60 psi. If other f aucets or
sprinklers ar e on turn off other running w ater.
Water dripping fr om fauc et assembly Adjustment of water flow is needed.
Below sink units - remove the fauc et handle by firs t
removing the spout (pull str aight up) and then s lide the
handle off the faucet base. Then turn the small t-bar
about one half tur n to tighten the f aucet ass embly .
Water is black Carbon dust
Allow w ater to run through the unit to w aste f or
approximately 20 minutes to flush the f ilter and c harge
the carbon.
XII. Troubleshooting
XIII. Questions and Answers
13
Question Answer
Comments
Will low pH or acid water affect the MultiPure filter?
No.
Mineral components express ed as acidity
and alkalinity determine pH. Neutrality is 7;
below 7 is acidity; above 7 is alkalinity.
Does de ionized w ater or soft water have
any affect on Multi-Pure water?
No. N/A
Can the Multi-Pure System be connected to
an automatic ice-maker?
The below sink models can be connected to
both your sink and refrigerator, to any type of
water dispenser or ice-maker. You can use
the same unit installed under your sink to
also filter the water at your refrigerator.
To connect a single Drinking Water System
to both your sink and refrigerator, request an
"ice-maker tee" on the order form.
Can the Multi-Pure System be us ed during
an emergency or when the water is turned
off?
Yes, you can hand pump or siphon water
through the Multi-Pure Sys tem during an
emergency. CAUTION -- the Multi-Pure
Sys tem is not intended to be used where the
water is microbiologically unsafe or with
water of unknown quality without adequate
disinfection before or after the unit.
If water source is questionably
contaminated, it should be disinfected prior
to use. Add ¼ tsp of household bleach per
gallon of water; the Multi-Pure System will
remove this solution from the water. Hand
pump kits are available from Multi-Pure.
What causes "white" particles to appear in
Multi-Pure w ater when it is frozen or
boiled?
The natural minerals in the Multi-Pure water
solidify when the water is frozen, and those
minerals appear as white flakes or specks
when the ice melts.
Natural minerals are beneficial to good
health and their existence in drinking water
(in normal quantities) should not cause any
alarm. Minerals can be removed by Reverse
Osmosis technology, which is also available
from Multi-Pure on request.
Why does the Multi-Pure System reduce
Volatile Organic Chemicals, but not natural
minerals?
Minerals are totally dissolved in solution and
do not have an actual phys ical size; thus, the
minerals pass through the filter unchanged.
The materials used in Multi-Pure Drinking
Water Sys tems are specially selected for
their ability to react with the chemicals in the
water, but not with natural minerals that are
beneficial to good health.
Should se diment be removed with a
standard filter first?
In areas with excessive sedimentation,
prefiltration will help extend the operational
efficiency of the Multi-Pure cartridge;
however, in most areas this is not
necessary.
The Multi-Pure System contains a triple filter.
The outside m aterial is a prefilter that helps
protect the solid carbon block surface from
prematurely clogging with large sediment.
Why is the compressed activated carbon
block filtration system more efficient than
activated c arbon (loose granula r)
systems?
Multi-Pure's solid carbon block filters are
compacted into a dense s tructure causing
every molecule of water to be forced through
microscopic pores of carbon, effectively
reducing a wide range of contaminants of
health concern (see Section 3), as well as
adsorbing tastes and odors and removing
particulate m atter rem oved by typical
activated carbon filters.
The Water Quality Association reports that
"an activated carbon filter can reduce
organics and solid particles, as well as
offensive tastes and odors." Only precoat
and solid carbon block filters are engineered
to provide 0.5 micron mechanical filtration.
What is the difference between a "water
softener" a nd the Multi-Pure Drinking
Water System?
Softeners are not used to treat drinking
water; they are used only to change the water
hardness. Softeners put sodium into the
water in exchange for magnesium or
calcium ions. Multi-Pure Drinking Water
Sys tems do not remove diss olved minerals,
so, the pH is not changed. Natural minerals
most often found in water are considered to
be essential to good health.
Soft water is good for bathing and laundering
and may extend the life of hot water heaters
and boilers. However, soft water should not
be used for watering plants or lawns. It is
recommended that you bypass a water
softener when installing your Multi-Pure
Drinking Water System.
Can the Multi-Pure System be used on
untreated water?
If water source is questionable, it should be
disinfected prior to use. Add ¼ tsp of
household bleach per gallon of water; the
Multi-Pure System will remove this solution
from the water. Consult your nearest public
water utility for assis tance or guidelines on
proper treatment of untreated water.
Multi-Pure Systems are designed to be used
on treated water systems; they are not
intended to be used where the water is
microbiologically unsafe or with water of
unknown quality without adequate
disinfection before or after the unit. Systems
certified for cyst reduction may be be used
on disinfected waters that may contain
filterable cys ts.
If you have any questions regarding the installation of your Multi-Pure Drinking Water System or for replacement filters,
Please call your authorized independent dealer
.
F508CB-MPADC/0603
Maintenance Problems
Flushing / disinfecting the unit housing: Multi-
Pure recommends that you not allow water to sit in
a unit for extended periods of time without it being
used. If a unit is left unused for more than 10 days,
it may need to be flushed/disinfected before you
resume use.
Stuck / Sticking Diverter Valve: Normally caused
by a mineral (calcium) buildup around the diverter
stem. There are two methods for solving this problem (Vegetable Oil or Vinegar).
To flush a unit that may be contaminated:
1. Confirm that water is turned off to the unit.
2. Relieve the water pressure (if below sink unit) by opening the unit faucet.
3. Remove and discard the used filter.
4. Clean & rinse out the inside of the housing.
5. Add 5 to 7 drops of bleach, such as Clorox™ or Purex™ (5 ¼% sodium hypochlorite) to the
bottom canister.
6. Reconnect the housing top and bottom without the replacement filter.
7. Turn on water and let unit housing fill up with the water/bleach solution.
8. Allow unit to soak for at least 30 minutes.
a. Countertop Units: To disinfect the spout, place your finger over the tip of the spout and turn
the unit upside down. Repeat this procedure 2 or 3 times during the 30-minute soak period.
b. Below Sink Units: To disinfect the faucet spout, remove the spout and place it in a container
with one-quart of water and bleach (use 5 drops of bleach) and allow to soak for 30 minutes.
9. After the housing has soaked for 30 minutes, disassemble the top and bottom and pour out the
water/bleach solution. Rinse out the inside of the housing.
10. Replace the filter (cartridge) following the instructions with the new filter.
11. Follow the instructions with the replacement filter for reconnecting and flushing your unit.
Vegetable Oil (Using vegetable oil to lubricate the diverter valve does not dissolve the mineral
deposits which build up and cause the sticking; thus it will be necessary to repeat this procedure
from time to time)
1. Unscrew diverter valve from faucet.
2. Pour a little vegetable oil in the inlet hole.
3. Pull the diverter valve stem in/out several times to lubricate it thoroughly.
4. Replace diverter valve on faucet.
Vinegar (Using vinegar to dissolve the mineral deposits may cause discoloration)
1. Unscrew diverter valve from faucet.
2. Soak diverter valve in vinegar for 10 minutes.
3. Rinse and replace diverter valve on faucet.
Diverter Stem Stuck (If diverter stem is not operating properly - sticking)
1. Disconnect diverter valve from faucet.
2. Push pin in -- if you can push the pin easily, there was air in the tubing.
3. Reconnect diverter valve.
Loading...