CPR INFORMATIQUE
http://yome.ca
317 Taschereau, La Prairie, Québec, J5R 1T4, 1 (877) TON-ORDI
GPS VEHICLE TRACKER
USER MANUAL
Preface
Thank you for purchasing GPS Vehicle Tracker. This manual shows how to operate the device
smoothly and correctly. Make sure to read this manual carefully before using this product. Please note
that specification and information are subject to changes without prior notice in this manual. Any
change will be integrated in the latest release. The manufacturer assumes no responsibility for any
errors or omissions in this document.
1
PDF created with pdfFactory trial version www.pdffactory.com
Content
1 Summary ------------------------------------------------------------------------------------------------- 3
2 Application ------------------------------------------------------------------------------------------------ 3
3 Hardware Description
3.1 Connectors ---------------------------------------------------------------------------------------- 3
3.2 Wires Connection -------------------------------------------------------------------------- ------- 4
3.3 External Relay Connection ---------------------------------------------------------- ------- 4
4 Specifications ---------------------------------------------------------------------------------------- 5
5 SIM Card Installation -------------------------------------------------------------------------- 5
6 Startup ------------------------------------------------------------------------------------- ----------- 6
7 Usage --------------------------------------------------------------------------------------------------- 6
8 Fortifying Mode --------------------------------------------------------------------------------- --------- 6
8.1 Engine Started Alert ---------------------------------------------- --------- -------- 7
8.2 Movement Alert --------------------------------------------------------- --------- -------- 7
8.3 Power Cutoff Alert-------------------------------------------------------- --------- -------- 7
8.4 Application in the Car Alarm System -------- -------- --------- -------- --------- --- 8
8.5 Checking the Working Status ----------------------------------------- --------- -------- 8
9 Tracking Mode -------------------------------------------- --------- -------- -------- -------- 7
9.1 Initialization ---------------------------------- --------- ---------------- -------- 9
9.2 Change Password ---------------------------------- --------- -------- -------- -------- 9
9.3 Authorization ---------------------------------- --------- -------- -------- -------- 9
9.4 Auto-Track ---------------------------------- --------- ------- -------- -------- -------- 9
9.5 Geo-fence ---------------------------------- --------- -------- -------- 9
9.6 Movement Alert ---------------------------------- --------- -------- -------- 11
9.7 Overspeed Alert ---------------------------------- --------- -------- -------- 11
9.8 IMEI Checking ------------------------------ --------- -------- ------- --------- 13
9.9 SOS Function --------------------------------- --------- -------- -------- 13
9.10 Low Battery Alert --------------------------- --------- --------- ------- -------- 13
9.11 SMS Center ------------------------------ --------- -------- -------- ------- 14
10 Monitoring Mode ------------------------------ --------- -------- 14
11 Remote Oil&Electricity Cut-off Function--------------------------------------- --------- -------- 14
12 GPRS Setting ------------------------------------------------------------------- - 15
13 Cautions --------------------------------------------------------------------- 15
14 Faults & Solutions --------------------------------------------------------------------- 16
2
PDF created with pdfFactory trial version www.pdffactory.com
1 Summary
GPS antenna connector
Working based on existing GSM/GPRS network and GPS satellites, this product can
locate and monitor any remote targets by SMS or GPRS,and guard against theft of
Vehicle.
2 Applications
l Rental vehicle / Fleet management etc
l Covert tracking
3 Hardware Description
3.1 Connectors
SIM card slot
GSM antenna connector
USB connector
3
PDF created with pdfFactory trial version www.pdffactory.com
Wires connectors SIM card lockhole
LED indicator
3.2 Wires Connection
1234567
Connect here with the
1. Black wire:-12V;
2. Red wire:+12V;
3. Purple wire:ACC;
4.White wire:connecting guard against theft implement(reserve-wire,it can be
connected or not.)
5.Microphone
6.External-relay connector
7.SOS button
3.3
External relay Connection
External relay
tracker (re. 3.2 Wire 6 )
Wire for car oil connecting
4
PDF created with pdfFactory trial version www.pdffactory.com
4 Specification.
SIM card
lockhole
to open the SIM card slot
Content Specs.
Dimension. 80mm x 60mm x 25mm
Weight 100g
Network GSM/GPRS
Band 850/900/1800/1900Mhz or 900/1800/1900Mhz
GPS chip SIRF3 chip
GPS sensitivity -159dBm
GPS accuracy 5m
Reacquisition 0.1s Cold status 45s
Time To First Fix
Warm status 35s
Hot status 1s
Car charger
Battery Chargeable changeable 3.7V 1100mAh Li-ion battery
Standby 50hours
Storage Temp. -40°C to +85°C
Operation Temp. -20°C to +55°C
Humidity 5%--95% non-condensing
12—24V input
5V output
5 SIM card installation
Make sure that there is no call transfer and call display is on, and PIN code off.
Steps:
1. Use a pen to open the SIM card slot
2. Put a SIM card into the slot.
3.Insert the slot with SIM card into the tracker.
Use a pen point in the
5
PDF created with pdfFactory trial version www.pdffactory.com
Open the SIM card slot
Put a SIM card into the slot.
Insert the slot with SIM card into the tracker.
6 Startup
l Put the SIM card in place,the LED indicator will flash after several
seconds.(NOTE:The tracker turns on atuomatically while the sim card slot be
inserted,and the tracker turns off automatically while the sim card slot take out.)
l After connecting the wires with the tracker and the car,then you can see the LED
indicator flashs green arounds the wires connector(re.3.1 wires connector)
l In 40-60 seconds, the unit will start to work and receive the GSM signals as well as
the GPS signals.When this unit receives GPS signals normally, you can use it and
do all the following settings.
7 Usage
The tracker has three working modes: Fortifying mode, Tracking mode and Monitoring
mode.
8 Fortifying Mode
When turn on the tracker, the default mode is Fortify mode.In fortifying mode, you can
call the tracker to activate the “protection” for your loved car or vehicle. The indicator will
flash every 4 seconds when the “protection “ is activated.
While the “protection” will be deactivated when you dial up the tracker again, the indicator
will flash every 1 second when the deactivation is done.
6
PDF created with pdfFactory trial version www.pdffactory.com
Remark: If ACC is connected, then you can not activate the “protection” for your car. The
tracker will be triggered to send an alert under one of following conditions:
8.1 Engine Started Alert
In fortifying mode, the tracker will start the ACC examine automatically. It will warn up
the user when the engine is started.
Alert SMS format: fortify! + lat./long.
It will keep sending such an alert every 3 minutes, you can send message to stop it.
8.2 Movement Alert
This function is using for the owner to get an alert when the tracker moves out of a
restricted district (500m radius),
Response SMS format: moved!+lat./long..
It will keep sending such an alert every 3 minutes, you can send message to stop it.
8.3 Power Cutoff Alert
In this mode, the tracker will warn up the user automatically when the main power is cut
off unwontedly,such as if someone cut the wire connected the car with the device, it will
alert “Battery with coordinates”.
Alert SMS format: battery! + lat./long.
It will keep sending such an alert every 3 minutes, you can send message to stop it.
NOTE: These three alerts only occurred when the “ protection ” is activated in fortifying
mode.
7
PDF created with pdfFactory trial version www.pdffactory.com
8.4
Application in the Car Alarm System
If your car equipped with a car alarm system,you can connect the white wire(re.3.2
wire4) to the positive wire of microphone on the car alarm.The authorized number will
receive an alert if the car alarm sounds more than 10 seconds
.
Alert SMS format:
lat: 22.567835N long: 114.051397E speed: 000.0 23/12/09 01:55 bat:F Signal:F
Trigger imei:356895033307722
8.5 Checking the Working Status ( fortify or no fortify )
You can send SMS command message to tracker, it will report “ fortifying “ or “ no fortify
“ to you.
Reply message means out of Fortifying mode, Reply message means under Fortifying
mode.
When the tracker is in tracking mode or monitoring mode, send a SMS command
message to switch to the "Fortifying mode", under fortifying mode, make a call to
activate the protection of your loved ones or car
9 Tracking Mode
9.1 Initialization
Send SMS message to the unit, it will reply “begin ok” and initialize all the settings.
9.2 Change the Password
Send SMS message change the password.
Remark:
9.2.1 Be sure keep the new password in mind, you have to upload the software to
restore the original setting in case of losing the new password.
8
PDF created with pdfFactory trial version www.pdffactory.com
9.3 Authorization
There are only 5 numbers able to be authorized numbers.
9.3.1 Setup:Send SMS message phone number to set up the first
authorized number.The other authorized numbers should be setup by the first
authorized number. If the number is successfully authorized, the unit will reply SMS as
“admin ok!”.
9.3.2 Cancel:Send SMS message number to delete the authorized number.
9.3.4 When an authorized number dials up the unit, it will hang up and report a real-time
Geo-info as below:
Lat: 22.566901 long: 114.051258 speed: 0.00 14/08/09 06.54 bat:F Signal:F help me
imei:354776031555474
Lat: 22.566901 long: 114.051258==Coordinate
0.00 == speed
14/08/09 06.54== Date&Time
bat:F == battery power is full,while ‘L’means battery power is low
Signal:F == Full GPS signal ‘L’ means no GPS signal
help me == the SOS message, this section is blank for tracking message
354776031555474== IMEI
9.4 Auto-Track
This function is using for the user to receive SMS with Geo-info in a certain time.
9
PDF created with pdfFactory trial version www.pdffactory.com
9.4.1 Set up: Send SMS message to the unit, it will report the Geo-info at 30s intervals
for 5 times.(s: second, m: minute, h: hour).You will receive a reply as “t030s005n OK” if
the setting is successful. The setting must be in 3 digits and at maximum 255 in value.
9.4.2 Send SMS message to the unit, it will reply SMS heaps of times. You will receive a
reply as the setting is successful.
9.4.3 Cancel: Send message to delete the “ auto track “.
Remark: the interval must not be less than 30s.
9.5 Geo-fence
Set up a geo-fence for the unit to restrict its movement within a district. The unit will
send message to the authorized numbers when it moves out of this district.
Notes: This function will be invalid if the unit moves outside the district. You need to
re-set it if you want this function again.
9.5.1 Setup:Send SMS message to the unit to set the restricted district.
Remark :The first latitude&longitude is coordinate of the top left corner of the Geo-fence,
while the second latitude&longitude is the coordinate of the bottom right corner.
9.5.2 Cancel:Send SMS message to deactivate this function..
9.5.3 Response SMS format: stockade!+geo-info. It will alarm one time in each setting.
9.6 Movement Alert
This function is using for the owner to get alarm when the tracker moves out of a
restricted district.
10
PDF created with pdfFactory trial version www.pdffactory.com
9.6.1
Setup: Send SMS message to the unit to set the movement alert.
9.6.2
Cancel: Send SMS message to deactivate the movement alert.
This function will be out of effect after the unit moves outside the district.
Response SMS format: move!+geo-info. It will alarm one time in each setting.
9.7 Overspeed Alert:
This function is using for the owner to control the target’s speed.
9.7.1 Setup: Send SMS message to the unit (suppose the speed is 80km/h), and it will
reply “speed ok!”. When the target moves exceeding 80 km/h, the unit will send SMS
speed+080!+Geo-info to the authorized numbers. It will keep sending such an alert
every 3 minutes.
9.7.2 Cancel: Send SMS message to deactivate the overspeed alert
Remark: It is recommended that the speed alarm is set at not less than 50km/h. For
below that rate, it may cause the excursion of the GPS signal influenced by clounds etc.
Response SMS format: speed+080!+Geo-info (suppose the speed is 80km/h).
The tracker will check the speed in 3 minutes interval and alarm if it is overspeed.
9.8 IMEI Checking:
Send SMS message to the unit to check the IMEI number of the unit.
9.9 SOS Button
Press the SOS for 3 second, it will send “help me !+ Geo-info” to all the authorized
numbers every 3 minutes. It will stop sending such a SMS when one of the authorized
number reply SMS message to the tracker.
11
PDF created with pdfFactory trial version www.pdffactory.com
9.10 Low Battery Alert
It begins to send SMS to the user every 30minutes when the the battery voltage is lower
than 3.7V.
SMS format: low battery+Geo-info.
9.11 SMS Center ( or appointed number)
9.11.1 Setup: Send SMS message phone number to setup the SMS center.
If the SMS center is set up, when an authorized number sends SMS or makes a calll to
the tracker, the tracker will reply a SMS with Geo-info & authorized number to SMS
center.
9.11.2 Cancel: Send SMS message to cancel the SMS center.
Response SMS format: authorized number+Geo-info
Note:
◆The SMS message must in Text format, can’t be identified for PDU format.
◆Power on the tracker outdoor when use the tracker for the first time, it can search the
GPS signal nearby, it also greatly shorten the time of searching the GPS signal for the
future use.
10 Monitoring Mode(voice surveillance mode)
Send SMS message, the response from the tracker is “monitor ok” then
you can hear the voice around the tracker after your call。
12
PDF created with pdfFactory trial version www.pdffactory.com
11 Remote Oil&Electricity Cut-off Function
This function is using for the car owner to send a SMS remotely to stop a moving vehicle.
11.1 Setup: Send SMS command message to the tracker to cut off the oil and electricity
of the car to stop the car.
Reply format: powercar ok. You will receive such a reply if the setting is successful.
11.2
Cancel: Send SMS command message to the tracker to restart the car again.
Reply format: powercar ok. You will receive such a reply if the setting is successful.
13 Cautions
Please comply with the instructions to extend the unit life:
1. Keep the unit dry. Any liquid, i.e. rain, moisture, may destroy or damage the inside
circuitry.
2. Don’t use & store the unit in dusty places.
3. Don’t put the unit in overheated or overcooled places.
4. Handle carefully. Don’t vibrate or shake it violently.
5. Clear the unit with a piece of dry cloth. Don’t clean in chemicals, detergent.
6. Don’t paint the unit, this may cause some foreign materials left in between the parts.
7. Don’t disassemble or refit the unit.
8. Please use the battery and charger provided by manufacturer. Using other batteries
and chargers will cause unwanted situation.
9. Don’t dismount the antenna randomly, or use other antennas. This may interfere the
transmission, and increase the radiation as well.
13
PDF created with pdfFactory trial version www.pdffactory.com
Loading...