1GE+WIFI EPON ONU User Manual
1GE+WIFI EPON ONU
USER MANUAL
1GE+WIFI EPON ONU User Manual
Contents
Contents ...................................................................................................................................... I
Chapter 1 Product Introduction
...................................................................................... 1
1.1 Product Description....................................................................................................... 1
1.2 Special features ............................................................................................................. 1
1.3 Technical Parameter ..................................................................................................... 2
1.4 Application chart ............................................................................................................ 2
1.5 Panel description ........................................................................................................... 3
Chapter 2 Quick Installation
............................................................................................ 5
2.1 Standard Packing Contents ......................................................................................... 5
2.2 Quick Installation ........................................................................................................... 5
Chapter 3 Configuration
.................................................................................................... 7
3.1 Login ................................................................................................................................ 7
3.2 Status .............................................................................................................................. 7
3.2.1 Device Information .................................................................................................... 7
3.2.2 WAN Connection Info ............................................................................................... 8
3.2.3 User Information ....................................................................................................... 9
3.2.4 Remote Management Status .................................................................................... 10
3.3 Network ......................................................................................................................... 11
3.3.1 Internet ..................................................................................................................... 11
3.3.2 LAN ......................................................................................................................... 13
3.3.3 WLAN Configuration .............................................................................................. 16
3.3.4 Remote Management ............................................................................................... 17
3.3.5 QoS .......................................................................................................................... 19
3.3.6 Time Configuration ................................................................................................. 21
3.3.7 Router Configuration ............................................................................................... 21
3.4 Security ......................................................................................................................... 22
3.4.1 WAN Access Configuration ..................................................................................... 22
3.4.2 Firewall .................................................................................................................... 23
Page I
1GE+WIFI EPON ONU User Manual
3.4.3 MAC Filter .............................................................................................................. 24
3.4.4 Port Filter ................................................................................................................. 24
3.5 Application .................................................................................................................... 25
3.5.1 DDNS Configuration ............................................................................................... 25
3.5.2 Advanced NAT Configuration ................................................................................. 25
3.5.3 UPNP Configuration ................................................................................................ 27
3.5.4 IGMP Configuration ................................................................................................ 28
3.5.5 MLD Configuration ................................................................................................. 29
3.5.6 Other ........................................................................................................................ 30
3.6 Management ................................................................................................................ 30
3.6.1 User Management .................................................................................................... 30
3.6.2 Device Management ................................................................................................ 31
3.6.3 Log File Configuration ............................................................................................ 33
3.7 Diagnosis ...................................................................................................................... 33
3.7.1 Network Diagnosis .................................................................................................. 33
3.8 Help ............................................................................................................................... 35
Chapter 4 Examples
......................................................................................................... 36
4.1 Internet service ............................................................................................................ 36
4.1.1 Requirement ............................................................................................................ 36
4.1.2 Steps ........................................................................................................................ 36
4.2 IPTV service ................................................................................................................. 41
4.2.1 Requirement ............................................................................................................ 41
4.2.2 Steps ........................................................................................................................ 41
Chapter 5 FAQ
................................................................................................................... 44
Page II
1GE+WIFI EPON ONU USER MANUAL
Chapter 1 Product Introduction
1.1 Product Description
Thank you for choosing the 1GE+WIFI EPON ONU. The terminal devices are designed for
fulfilling FTTH and triple play service demand of fixed network operators or cable operators. The
box is based on the mature Gigabit EPON technology, which have high ratio of performance to
price, and the technology of Layer 2/3. They are highly reliable and easy to maintain, with
guaranteed QoS for different service. And they are fully compliant with technical regulations such
as IEEE802.3ah and technical requirement of EPON Equipment (V2.1 and above version) from
China Telecom.
1.2 Special features
Figure 1-1: 1GE+WIFI EPON ONU
Plug and play, integrated auto detecting, auto configuration, and auto firmware upgrade
technology.
Support OAM remote configuration and maintenance.
Support rich VLAN, DHCP Server and IGMP snooping multicast feature.
Fully compatibility with OLT based on Broadcom/PMC/Cortina chipset.
Support NAT, Firewall function.
The WAN port supports bridge or router mode.
Page 1
1GE+WIFI EPON ONU USER MANUAL
1.3 Technical Parameter
Technical items
PON interface 1EPON connector, SC single-mode/single-fiber, symmetric 1.25Gbps
Wavelength Tx1310nm,Rx 1490nm
Optical interface SC/PC connector
Interface
Wireless
Indicator
Operating condition
Storing condition
Power supply DC 12V,0.5A
Power consumption
1* 10/100/1000Mbps auto adaptive Ethernet interfaces. Full /Half Duplex,
RJ45 connectors.
Compliant with IEEE802.11b/g/n, 300Mbps, 2T2R 1 internal antenna, 1
external antenna
5 indicators，POWER、LOS、REG、LINK/ACT、SYS
-5
℃～55℃，
-30
℃～60℃，
≤
6W
10%～90%（non-condenseing）
10%～90%（non-condenseing）
Descriptions
Dimension
Net weight 0.13Kg
120mm×78mm×30mm
1.4 Application chart
（
L×W×H）
Page 2
1GE+WIFI EPON ONU USER MANUAL
Figure 1-2: Application chart
1.5 Panel description
Interface panel
Name Function
ON/OFF Power switch.
POWER Connect with power adaptor.
RST
LAN Ethernet port.
PON EPON interface, SC/PC type, single mode optical fiber cable.
Indication Panel
Figure 1-3: Interface panel
Reset button. Press down less than 10s to restart ONU and more
than 10s to restore factory default.
Figure 1-4: Indication panel
LED Mark Status
Page 3
Description
1GE+WIFI EPON ONU USER MANUAL
On T
he
WiFi
runs normal.
OFF
The
WiFi
is powered down.
Blink
Port is sending or/and receiving data.
ON The device is registered to the EPON system.
OFF
Device is not registered to the EPON system.
Blink
Device is registering.
Blink
Device does not receive optical signals.
ON The device is powered up.
OFF
The device is powered down.
WiFi WiFi
ON Port is connected properly.
Ethernet LINK/ACT
Registration
REG
Optical
LOS
signal
Power POWER
Off
Port connection exception or not connected.
OFF Device has received optical signals.
Page 4
1GE+WIFI EPON ONU USER MANUAL
Chapter 2 Quick Installation
2.1 Standard Packing Contents
When you receive our products, please check carefully to make sure that our products
whether have some defects or not. If something wrong with shipping, please contact carrier;
other damage or lack of some parts, please contact with dealer.
Contents Description
ONU 1 pc
Power Adapter 1 pc
User Manual 1 pc
2.2 Quick Installation
1. Connecting the optical fiber cable to the unit.
a) Remove the protective cap of the optical fiber.
b) Clean the end of the optical fiber with an optical fiber end cleaner.
c) Remove the protective cap of the ONU optical interface (PON interface). Connect the
fiber to the PON port on the unit.
Note: When measuring the optical power before connecting to the ONU, it is
recommended to use a PON Inline Power Meter.
While connecting, please note:
Keep the optical connector and the optical fiber clean.
Make sure there are no tight bends in the fiber and that the bending diameter is greater
than 6cm. Otherwise, the optical signal loss may be increased, to the extent that signal
may be unavailable.
Cover all optic ports and connectors with protective cap to guard against dust and
moisture when the fiber is not used.
2. Apply power to the unit. Push the power button.
3. After the ONU is power ON, Indicators should light up as for normal operation. Check
whether the PON interface status LED (PON) is on continuously. If it is, the connection is
normal; otherwise there is either problem of the physical connection or the optical level at
Page 5
1GE+WIFI EPON ONU USER MANUAL
either end. This may be caused by either too much or too little attenuation over the optical
fiber. Please refer to the Layout Description section of this installation manual for normal
LED activity.
4. Check all signal levels and services on all the ONU communication ports.
Unit Installation Adjustment
Installing the ONU on a horizontal surface (Bench top)
Put the ONU on a clean, flat, sturdy bench top. You must keep the clearance for all sides
of the unit to more than 10cm for heat dissipation.
Installing the ONU on a vertical surface (Hanging on a wall)
You can install the ONU on a vertical surface by using the mounting holes on the bottom
of the ONU chassis and two flat-head wood screws.
a) Insert the screws into the wall. The screw positions must be in the same horizontal line
and the distance between them must be 145mm. Reserved at least 6mm between the
screw caps and the wall.
b) Hang the ONU on the screws through the mounting holes.
Page 6
1GE+WIFI EPON ONU USER MANUAL
Chapter 3 Configuration
After finishing the basic connection configuration, you can use its basic function. In order
to satisfy individuation service requirements, this charter provides the user parameter
modification and individuation configuration description.
3.1 Login
The device is configured by the web interface. The following steps will enable you to login:
1、 Conform “2.2 Quick Installation” to install;
2、 The device default IP is 192.168.1.1;
3、 Open your web browser, type the device IP in address bar;
4、 Entry of the user name and password will be prompted. Enter the default login user name
and password.
By default, there are two user levels for management. Administration level user name is
"admin", password is "admin" . Normal level user name is "user", password is "user".
Figure 3-1: Login
3.2 Status
This part shows the main information of product.
3.2.1 Device Information
This page shows the
device basic information, such as Device Model, Device ID,
Page 7
Hardware
1GE+WIFI EPON ONU USER MANUAL
Version, Software Version.
Figure 3-2: Device Information
3.2.2 WAN Connection Info
3.2.2.1 IPv4 connection Information
This page shows IPv4 WAN connection information you have configured.
Figure 3-3: WAN Information IPv4
3.2.2.2 IPv6 connection Information
This page shows IPv6 WAN connection information you have configured.
Page 8
1GE+WIFI EPON ONU USER MANUAL
Figure 3-4: WAN information IPv6
3.2.2.3 EPON Inform
This page shows the PON information, such as Connection Info, Link performance
statistics, Warning and power, temperature, voltage, Biascurrent.
Figure 3-5: EPON Information
3.2.3 User Information
3.2.3.1 WLAN Interface Information
This page shows WLAN interface information.
Page 9
1GE+WIFI EPON ONU USER MANUAL
Figure 3-6: WLAN Interface Information
3.2.3.2 LAN Interface Information
This page shows the Ethernet port information, including Gateway Info, Receive/Send Info,
LAN Device Info.
Figure 3-7: LAN Interface Information
3.2.4 Remote Management Status
3.2.4.1 TR069 Connection Status
This page shows the Remote Connection status.
Page 10
1GE+WIFI EPON ONU USER MANUAL
Figure 3-8: TR069 Connection Status
3.2.4.2 TR069 Configuration Status
This page shows the Remote Configuration status.
Figure 3-9: TR069 Configuration State
3.3 Network
3.3.1 Internet
This page allows the user to configure WAN connections. You can only configure route
mode WAN connections here. The device default settings is bridge mode .
Page 11
1GE+WIFI EPON ONU USER MANUAL
Figure 3-10: WAN Connection
Parameter Illustration
The list of WAN connection name that has been created.
If you want to create a new WAN connection, please select “Create
WAN Connection” and input other Parameter at the same time and
then click “Create” button. If you want to edit WAN connection,
Connection Name
please select the wan connect name you want to edit and change
some Parameter and then click “Modify” button. If you want to
delete one connection, please select the wan connection you want
to delete and then click “Delete” button.
New Connection Name Name of new connection that you want to create.
Bridge/Route. The device works on route mode with this WAN
Mode
connection.
IP Protocol Mode IPv4/IPv6
WAN ip mode DHCP/Static/PPPoE
Checked indicates NAT function is enabled. Unchecked indicates
Enable NAT
NAT function is disabled.
Checked indicates the packets are transmitted by the PON port
Enable VLAN
VLAN
take VLAN tag. Unchecked indicates the packets are transmitted
by the PON port don’t take VLAN tag.
Input the VLAN ID you want to set. Range is 0~4094. Input 0
VLAN ID
means don’t use any VLAN.
802.1P Select VLAN priority you want to set. Range is 0~7.
Page 12
1GE+WIFI EPON ONU USER MANUAL
MTU
Max transfer unit. Default Value (in Byte):
1500(static/DHCP) or 1492(PPPoE).
Username PPPOE account.
PPP
Password PPPOE password.
Method of WAN connection Obtains IP address. If link type is
IP Type/PPP TransType
PPP, PPP TransType will be PPPOE; if link type is IP, IP Type will
be static or DHCP.
Service mode indicates what the wan connection is used for.
Service Mode
There are INTERET and TR069 for choosing.
3.3.2 LAN
This page supports the management of the ONU's IP address, dynamic address
management, including dynamic address distribution and relevant parameters distribution,
such as lease time, address range, DHCP Proxy, etc.
3.2.3.1 LAN IPv4 Address Settings
Figure 3-11: LAN IPv4 Address Settings
Page 13
1GE+WIFI EPON ONU USER MANUAL
Figure 3-12: Edit DHCP IP Pool
Parameter Illustration
LAN IP Address LAN IP address.
Subnet Mask LAN IP mask.
Enable DHCP Server Enable ONU DHCP server.
Start IP Address The start IP address of DHCP IP pool.
End IP Address The end IP address of DHCP IP pool.
Lease Time Lease time of the IP address.
Manual DNS Checked indicates using LAN IP as DNS server. Enable indicates you
should fill in DNS server in the textbox manually.
Enable DHCP Proxy The DHCP server ip address.
Page 14
1GE+WIFI EPON ONU USER MANUAL
3.2.3.2 LAN IPv6 Address Settings
Figure 3-13: LAN IPv6 Address Settings
3.2.3.3 LAN IPv6 DHCP configuration
Figure 3-14: LAN IPv6 DHCP configuration
Page 15
1GE+WIFI EPON ONU USER MANUAL
3.2.3.4 RA Configuration
Figure 3-15: RA Configuration
3.3.3 WLAN Configuration
Figure 3-16: WLAN Configuration
Page 16
1GE+WIFI EPON ONU USER MANUAL
Figure 3-17: WLAN Advanced Configuration
3.3.4 Remote Management
3.3.4.1 ITMS Server
Figure 3-18: ITMS Server
Page 17
1GE+WIFI EPON ONU USER MANUAL
3.3.4.2 Upload CA Certificate
Figure 3-19: Upload CA Certificate
3.3.4.3 LOID
This page allows the user to configure LOID and password which are used for registering to
OLT.
Figure 3-20: LOID settings
Page 18
1GE+WIFI EPON ONU USER MANUAL
3.3.5 QoS
3.3.5.1 Policy Configuration
This page allows the user to configure QoS.
Figure 3-21: Policy Configuration
3.3.5.2 QoS Classify
Figure 3-22: QoS Classify
Page 19
1GE+WIFI EPON ONU USER MANUAL
Figure 3-23: QoS Classify Edit
3.3.5.3 TC
Figure 3-24: Traffic Flow Control Information
Page 20
1GE+WIFI EPON ONU USER MANUAL
3.3.6 Time Configuration
Figure 3-25: Timer Server
3.3.7 Router Configuration
This page allows the user to configure static routing.
3.3.7.1 RIP
This page allows the user to
3.3.7.2 Static Route
configure RIP
Figure 3-26: RIP
.
This page allows the user to specify a WAN connection as the Route Interface, then configure
destination IP, mask and gateway.
Page 21
1GE+WIFI EPON ONU USER MANUAL
Figure 3-27: Static Route
Parameter Illustration
DestNet
Subnet Mask
Gateway
Interface
Destination network address
The Mask of destination network address.
Gateway IP address of static routing.
Select WAN connection as static routing interface.
3.4 Security
3.4.1 WAN Access Configuration
This page allows the user to set WAN Access Configuration.
Figure 3-28: Firewall
Page 22
1GE+WIFI EPON ONU USER MANUAL
3.4.2 Firewall
3.4.2.1 Security Level
This page allows the user to set the level of the firewall (IPv4) .
Figure 3-29: Security Level
3.4.2.2 Attack Protection Configuration
This page allows the user to set the protection against DOS attacks.
Figure 3-30: Attack Protection Configuration
Parameter Illustration
Enable Anti-Hacking
Anti-Hacking Protection switch.
Protection
Firewall Level Low: Allow all inner or outer hosts to access.
Page 23
1GE+WIFI EPON ONU USER MANUAL
Middle: Allow inner or outer hosts which are limited by the rules
that have been created to access.
High: Forbid ICMP Input, Forbid Port Scan, Denial of Service
protections.
3.4.3 MAC Filter
This page allows the user to set the relevant parameters of the MAC filter function. The
user interface will display the MAC Filter rules after setting completed.
Figure 3-31: MAC Filter
3.4.4 Port Filter
This page allows the user to set the port filter.
Figure 3-32: Port Filter
Page 24
1GE+WIFI EPON ONU USER MANUAL
3.5 Application
3.5.1 DDNS Configuration
This page allows the user to set DDNS configuration.
Figure 3-33: DDNS Configuration
3.5.2 Advanced NAT Configuration
This page allows the user to set Advanced NAT configuration.
3.5.2.1 ALG Configuration
Figure 3-34: ALG Configuration
Page 25
1GE+WIFI EPON ONU USER MANUAL
3.5.2.2 DMZ Configuration
Figure 3-35: DMZ Configuration
3.5.2.3 NAT Configuration
Figure 3-36: NAT Configuration
Page 26
1GE+WIFI EPON ONU USER MANUAL
3.5.3 UPNP Configuration
3.5.3.1 UPNP Configuration
Figure 3-37: UPNP Configuration
3.5.3.2 DLNA Configuration
Figure 3-38: DLNA Configuration
Page 27
1GE+WIFI EPON ONU USER MANUAL
3.5.4 IGMP Configuration
3.5.4.1 IGMP SNOOPING
3.5.4.2 IGMP Proxy
Figure 3-39: IGMP SNOOPING
Figure 3-40: IGMP Proxy
Page 28
1GE+WIFI EPON ONU USER MANUAL
3.5.5 MLD Configuration
3.5.5.1 MLD SNOOPING Configuration
Figure 3-41: MLD SNOOPING Configuration
Parameter Illustration
Disable Disable IGMP. Multicast streams will flood to LAN port.
Enable snooping mode. Multicast streams will transmit to LAN
Enable
port when there is a member join the group.
3.5.5.2 MLD Proxy Configuration
Figure 3-42: MLD Proxy Configuration
Page 29
1GE+WIFI EPON ONU USER MANUAL
3.5.6 Other
3.5.6.1 IPTV
Figure 3-43: IPTV
3.6 Management
3.6.1 User Management
This page allows the user to change username or password. There are two User level
accounts: admin and user.
The admin account is able to access and modify all settings of ONU. It also can modify
user account’s username and password.
The user account can only be used to view configurations, status and configure few
parameters.
Page 30
1GE+WIFI EPON ONU USER MANUAL
Figure 3-44: User management
3.6.2 Device Management
3.6.2.1 Reboot
This page allows the user to reboot the device or restore factory default. The process of
reboot will take several minutes.
Figure 3-45: Reboot
3.6.2.2 Upgrade
This page allows the user to update the software of the device. Click the “browse” button to
select the software and then click the “Update” button to update.
Figure 3-46: Upgrade
Page 31
1GE+WIFI EPON ONU USER MANUAL
3.6.2.3 Restore Default
Figure 3-47: Restore Default
3.6.2.4 Config File Management
This page allows the user to backup and restore the configurations.
Figure 3-48: Config File Management
Parameter Illustration
Download Backup configurations to local computer.
Upload Restore configurations from local computer.
Page 32
1GE+WIFI EPON ONU USER MANUAL
3.6.3 Log File Configuration
Figure 3-49: Level
Figure 3-50: Set Loglevel
3.7 Diagnosis
3.7.1 Network Diagnosis
3.7.1.1 PING Diagnosis
This page shows about the ping test. You can diagnose connection status between ONU and
other devices.
Page 33
1GE+WIFI EPON ONU USER MANUAL
Figure 3-51: PING Diagnosis
Parameter Illustration
IP Address or Host Name Input the destination IP you want to ping.
WAN Interface Select the interface you want to test.
3.7.1.2 Tracer Diagnose
Figure 3-52: Tracer Diagnose
Page 34
1GE+WIFI EPON ONU USER MANUAL
3.7.1.3 Manually Inform Use Tr069
Figure 3-53: Manually Inform Use Tr069
3.8 Help
The Help information of ONU displays instruction and prompt of each web UI.
Figure 3-54: Help information
Page 35
1GE+WIFI EPON ONU USER MANUAL
Chapter 4 Examples
4.1 Internet service
There are two configuration methods for Internet service. One works on bridge mode and
another works on route mode.
4.1.1 Requirement
Scenario 1:
ONU works on bridge mode, service VLAN is 10. User gets IP address via DHCP.
Scenario 2:
ONU works on route mode, service VLAN is 10. ONU gets IP address via PPPoE.
4.1.2 Steps
For scenario 1, it doesn’t need to configure anything in ONU side but need to configure
VLAN in OLT side.
For scenario 2, except configuring VLAN in OLT side, it also needs to configure WAN
connection in ONU web.
4.1.2.1 Bridge mode for Internet service
In this example, we take V1600D and Huawei MA5680T for example, to introduce how to
configure Internet service.
1） V1600D Configurations
(1) Create VLAN
epon-olt (config)# vlan 10
epon-olt (config-vlan-10)# exit
(2) Configure uplink port
epon-olt (config)# inter g 0/3
epon-olt (config-if-ge0/3)#switchport hybrid vlan 10 untagged
epon-olt (config-if-ge0/3)#switchport hybrid pvid vlan 10
(3) Configure PON port
epon-olt (config)# inter epon 0/2
epon-olt (config-pon-0/2)# switchport hybrid vlan 10 tagged
(4) Configure ONU bridge mode by ONU web
Page 36
1GE+WIFI EPON ONU USER MANUAL
Figure 4-1: Bridge Mode
Page 37
1GE+WIFI EPON ONU USER MANUAL
Huawei MA5680T Configurations
(1) Create VLAN
MA5680T(config)#vlan 10 smart
(2) Configure uplink port’s VLAN
MA5680T(config)#port vlan 10 0/19 1
MA5680T(config)#interface giu 0/19
MA5680T(config-if-giu-0/19)#native-vlan 1 vlan 10
(3) Configure DBA profile
MA5680T(config)#dba-profile add profile-id 12 profile-name 1GE type3 assure 102400 max
899968
(4) Configure line profile
MA5680T(config)#ont-lineprofile epon profile-id 11 profile-name 1GE
MA5680T(config-epon-lineprofile-11)#llid dba-profile-id 12
MA5680T(config-epon-lineprofile-11)#commit
(5) Configure service profile
MA5680T(config)#ont-srvprofile epon profile-id 6 profile-name 1GE
MA5680T(config-epon-srvprofile-6)#ont-port eth 1
MA5680T(config-epon-srvprofile-6)#commit
(6) Authorize ONU
MA5680T(config)#interface epon 0/5
MA5680T(config-if-epon-0/5)#ont add 1 0 mac-auth 002A-8523-C610 oam ont-lineprofile-id
11 ont-srvprofile-id 6
(7) Configure service-port
MA5680T(config)#service-port 27 vlan 10 epon 0/5/1 ont 0 multi-service user-vlan 10
(8) Configure ONU bridge mode by ONU web
4.1.2.2 Route mode for Internet service
1) Add a WAN connection
Choose “Network > WAN > WAN Connection” in navigation menu. Add a route mode
WAN connection as the following Parameter.
New connection name is INTERNET.
Enable VLAN. VLAN ID is 10 and 802.1p is 0.
Service list is INTERNET.
Link type is PPP. And PPPoE username and password both are ppptest.
Other Parameters keep default.
Page 38
1GE+WIFI EPON ONU USER MANUAL
2) Enable DHCP server
Figure 4-2: Add a route WAN connection
Figure 4-3: Enable LAN DHCP server
3) OLT Configurations
V1600D configurations:
(1) Create VLAN
epon-olt (config)# vlan 10
epon-olt (config-vlan-10)# exit
(2) Configure uplink port
epon-olt (config)# inter g 0/3
epon-olt (config-if-ge0/3)#switchport hybrid vlan 10 untagged
epon-olt (config-if-ge0/3)#switchport hybrid pvid vlan 10
Page 39
1GE+WIFI EPON ONU USER MANUAL
(3) Configure PON port
epon-olt (config)# inter epon 0/2
epon-olt (config-pon-0/2)# switchport hybrid vlan 10 tagged
(4) Configure ONU WAN by ONU web
Figure 4-4: Route Mode Static IP
Huawei MA5680T Configurations:
(1) Create VLAN
MA5680T(config)#vlan 10 smart
(2) Configure uplink port VLAN
MA5680T(config)#port vlan 10 0/19 1
MA5680T(config)#interface giu 0/19
MA5680T(config-if-giu-0/19)#native-vlan 1 vlan 10
(3) Configure DBA profile
MA5680T(config)#dba-profile add profile-id 12 profile-name 1GE type3 assure 102400 max
899968
(4) Configure line profile
MA5680T(config)#ont-lineprofile epon profile-id 11 profile-name 1GE
MA5680T(config-epon-lineprofile-11)#llid dba-profile-id 12
MA5680T(config-epon-lineprofile-11)#commit
(5) Configure service profile
MA5680T(config)#ont-srvprofile epon profile-id 6 profile-name 1GE
MA5680T(config-epon-srvprofile-6)#ont-port eth 1
MA5680T(config-epon-srvprofile-6)#commit
(6) Authorize ONU
MA5680T(config)#interface epon 0/5
Page 40
1GE+WIFI EPON ONU USER MANUAL
MA5680T(config-if-epon-0/5)#ont add 1 0 mac-auth 002A-8523-C610 oam ont-lineprofile-id
11 ont-srvprofile-id 6
(7) Configure service-port
MA5680T(config)#service-port 27 vlan 10 epon 0/5/1 ont 0 multi-service user-vlan 10
(8) Configure ONU WAN by ONU web
4.2 IPTV service
4.2.1 Requirement
ONU works on bridge mode, STB gets IP address from DHCP server, IPTV service VLAN is
10.
4.2.2 Steps
In this example, we take V1600D and Huawei MA5680T for example, to introduce how to
configure IPTV service.
1） V1600D Configurations
(1) Create VLAN
epon-olt (config)# vlan 10
epon-olt (config-vlan-10)# exit
(2) Configure uplink port
epon-olt (config)# interface g 0/5
epon-olt config-if-ge0/5)# switchport hybrid vlan 10 untagged
epon-olt (config-if-ge0/5)#switchport hybrid pvid vlan 10
epon-olt (config-if-ge0/5)# exit
(3) Configure PON port
epon-olt (config)# inter epon 0/1
epon-olt (config-pon-0/1)# switchport hybrid vlan 10 tagged
epon-olt (config-pon-0/1)# ip igmp snooping user-vlan 10 group-vlan 10 tagged
epon-olt (config-pon-0/1)# exit
(4) Enable IGMP Snooping
epon-olt (config)# ip igmp snooping enable
(5) Configure multicast port
epon-olt (config)# ip igmp snooping mrouter vlan 10 interface gigabitethernet 0/5
(6) Configure ONU LAN port
epon-olt (config)# inter epon 0/1
epon-olt (config-pon-0/1)# onu 1 ctc eth 1 mc_vlan add 10
epon-olt (config-pon-0/1)# onu 1 ctc eth 1 mc_tagstrip enable
Page 41
1GE+WIFI EPON ONU USER MANUAL
epon-olt (config-pon-0/1)# exit
(7) Configure ONU VLAN by ONU web
2） Huawei MA5680T Configurations
(1) Create VLAN
MA5680T(config)#vlan 10 smart
(2) Configure uplink port VLAN
MA5680T(config)#port vlan 10 0/19 1
MA5680T(config)#interface giu 0/19
MA5680T(config-if-giu-0/19)#native-vlan 1 vlan 10
(3) Configure DBA profile
MA5680T(config)#dba-profile add profile-id 12 profile-name 1GE type3 assure 102400 max
899968
(4) Configure line profile
MA5680T(config)#ont-lineprofile epon profile-id 11 profile-name 1GE
MA5680T(config-epon-lineprofile-11)#llid dba-profile-id 12
MA5680T(config-epon-lineprofile-11)#commit
(5) Configure service profile
MA5680T(config)#ont-srvprofile epon profile-id 6 profile-name 1GE
MA5680T(config-epon-srvprofile-6)#ont-port eth 1
(6) Configure multicast VLAN and strip attribute
MA5680T(config-epon-srvprofile-6)#port multicast-vlan eth 1 10
MA5680T(config-epon-srvprofile-6)#port eth 1 multicast-tagstrip untag
MA5680T(config-epon-srvprofile-6)#commit
(7) Authorize ONU
MA5680T(config)#interface epon 0/5
MA5680T(config-if-epon-0/5)#ont add 1 0 mac-auth 002A-8523-C610 oam ont-lineprofile-id
11 ont-srvprofile-id 6
(8) Configure ONU VLAN by ONU web
(9) Configure service-port
MA5680T(config)#service-port 27 vlan 10 epon 0/5/1 ont 0 multi-service user-vlan 10
(10) Configure IGMP user
MA5680T(config)#btv
MA5680T(config-bTV)#igmp user add service-port 27 no-auth
(11) Configure multicast VLAN and multicast port
MA5680T(config)#mutlcast-vlan 10
MA5680T(config-mvlan10)#igmp uplink-port 0/19/1
(12) Configure multicast IGMP version
MA5680T(config-mvlan10)#igmp version v2
Page 42
1GE+WIFI EPON ONU USER MANUAL
This operation will delete all programs in current multicast vlan
Are you sure to change current IGMP version? (y/n)[n]: y
(13) Configure IGMP match mode
MA5680T(config-mvlan10)#igmp match mode disable
//disable mode indicates that OLT will match programs automatically according to members’
requirements but not program settings.
(14) Configure IGMP mode
MA5680T(config-mvlan10)#igmp mode proxy
Are you sure to change IGMP mode?(y/n)[n]:y
(15) Configure multicast VLAN member
MA5680T(config-mvlan10)# igmp multicast-vlan member service-port 27
Page 43
1GE+WIFI EPON ONU USER MANUAL
Chapter 5 FAQ
2. Q: All indicators are not lit?
A: (1) Power is off or power adapter is bad.
(2) Indicator LED switch is turned off.
3. Q: Why Los indicator flashes?
A: (1) There is no optical signal. Maybe the fiber is broke down or connection loosened.
(2) Optical power is too low.
(3) The fiber is dusty.
4. Q: LAN indicators are not lit?
A: (1) Indicator LED switch is turned off.
(2) The cable breaks down or connection loosened.
(3) The cable type incorrect or too long.
5. Q: PC can’t visit web UI?
A: (1) PC and ONU are not in the same network fragment. By default, LAN IP is
192.168.1.1/24.
(2) The cable breaks down.
(3) IP conflict or have loopback.
6. Q: User can’t surf the Internet normally.
A: (1) PC has set a wrong IP and gateway or network is bad.
(2) There is loopback or attack in network.
(3) Route mode WAN connection doesn’t get an IP or DNS is disabled.
7. Q: ONU stops to work after working for some time.
A: (1) Power supply is not working properly.
(2) The device overheats.
Page 44
Loading...