Shenzhen Yifang Digital Technology Co., Ltd.
WiFi Infrared universal remote control manual
EFUN
SW85,SW85*(* on behalf of the 0-9,A-Z), 6431N
Existing functions:
1. One-key distribution network ;
2. Remote control by mobile APP;
3. Support remote control air conditioning, TV and set-top box;
4. Learning function expands more categories (38K code-rate signal
learning is supported);
5, 360 ° no dead Angle signal coverage;
6. ALEXA and Google assistant voice control
7. Intelligent scene control;
Follow-up support:
1. Timing via cloud
2. Expand more categories (DVD, fan, power amplifier, etc.)
1
3. Air conditioning study;
4. Set-top box channel error correction feedback;
Usage:
A distribution network,
Default mode:
1. Long press the reset button for 5 seconds, indicator light enters the flash
state;
2. Enter the APP and select "universal remote control" to configure the
network as prompted;
Compatibility mode:
1. Long press the reset button for 5s ,indicator light enters the flash state;
2. Long press the reset button again for 5s ,indicator light will enter the
slow-flashing state;
3. Enter the APP, click "universal remote control" and click the "compatibility
mode" in the upper right corner to configure the network according to the
instructions.
Add fixed remote control
On the basis of the existing classification, fixed category of electric remote
control such as air conditioning remote control, television remote control,
set-top box remote control, etc
The addition method is simple and fast, but limited by the code base data, it
cannot guarantee that the electric appliance is 100% infrared controlled,
and some electrical appliances may be not supported.
2
Step1 Step2 Step3
Step4 Step5 Step6
3
3. Learning function
If you find the remote control can not control the appliance through the
previous method, you can use learning function to make the remote
control gain universal remote control ability to control electrical
appliances.
Note:
1. This version only supports 38K code rate signal learning. If you find
that universal remote control cannot accept the instructions of electric
remote control, maybe the code rate signal of the electric remote control
does not match.
2. When using the learning function, in order to ensure the universal
remote control receives instructions normally, please do not long press
the electric remote control to send out signal to the universal remote
control.Just short press it to send out the signal.
Step1 Step2 Step3
4
Step4 Step5 Step6
If you need to change or add a DIY remote control, click the”edit”
button in the upper right corner of the custom remote control panel to
make change:
5
Status definition of indicator:
Not connected to network: indicator light is always on;
Wait to connect to network: indicator light fast flash/slow flash;
Connect to network and the network is normal: the indicator light is off;
Connect to network and network is abnormal: indicator light is always on.
Transmission data: indicator light flashes once;
Enter the learning mode: the indicator light is always on.
Receiving learning instruction: indicator lights off;
Remarks:[reset mode] long press the reset button;
6
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body.
Loading...