Yifang Digital Technology SH320, SH360 User Manual
u
e
5
w
+
m
c
a
U
M
+
a
s
s
,
e
e
e
w
v
s
v
About
Thank yo
transform
more qu
888-415-
To set up
O
NEXTURN
for purchasing
your life and
stions, please
177 or visit us
your new NEXT
ner’s
Smart Kit
the NEXTURN
aking it easier
ontact our Cu
t www.nexturnu
RN+ Smart Kit
anual
Smart Kit! W
nd more conv
tomer Service
a.com
please follow b
hope this Kit
nient. If you ha
Representative
low instruction
1. Packing Contents
Unpack your NEXTURN+ Smart Kit to check the following parts and
accessories are enclosed:
Box Content picture describe
ill
e
at
.
①
②
③
④
X1 Smart
Zigbee
Gateway
X1 IR motion
sensor
X1 Smart
converter
X1 Smart plug
Connect your smart kit to network
Detect any motion around sensor
Switch your bulb remotely
Can be turn on/off remotely
1
2. Getting Started
Step 1 Configure the Smart Gateway
Note: To setup your smart gateway, you need to get the following things
ready
Available wireless network (WiFi Router)
●
● 1pcs Ethernet cable
● Smart phone or tablet
Features
X1 Door/
⑤
window sensor
X1 wireless
⑥
switch
⑦
X1 IP Camera
Detect door/window open/close state
Switch smart converter and plug
4 1pcs Smart plug
Remotely monitor your home or office
2
2. Check that the Internet access is available at your home;
3. Connect the attached power adapter to the Smart Gateway for power
supply.
4. Connect the smart gateway to the router via a Ethernet cable.
5. Push the register button to register gateway to network.
6. Connect smart phone or tablet to the WiFi router, which has been
connected with gateway.
Tips: Locate your smart kits within a range of 20 meters around the smart
gateway.
1. Power socket--connect DC adapter for power supply;
2. Ethernet jack--connect Ethernet cable
3. Reset button--reset the device (restore factory defaults) if
necessary;
4. Register button – register gateway to network
5. Antenna
Procedures
1. Open box ①,take out the gateway, and get a adapter which use for
gateway in box ②
3
Step2 NEXTURN+ APP
1. Connect your smart phone or tablet to the WiFi router, which has been
connected with gateway, go to APP store to find “NEXTURN+” APP ,
download and install it in your smart phone or tablet.
2. Run “NEXTURN+” APP, star to register a new account, and
“NEXTURN+” will send a confirm email to you, confirm it to sign in
“NEXTURN+”
3. Then follow the APP guide, add gateway and other smart kit devices.
Tips: 1.smart kit devices will connect to zigbee gateway automatically when
you power them
2. If the device has been registered to another gateway before, use the
magnetic rod to touch the device at the designated point for seconds. The
network indicator blinks a few times, indicating it start to register to a new
gateway.
4
Step 3 Add the IR motion sensor to the Network
1.Open box ②,take out the IR motion sensor.
2. Install one AAA battery into it.
3. Fix the IR motion sensor to one available location (e.g. the wall).
4. Run the “NEXTURN+” APP, go to “find devices” page, tap “find device”
button, it will appear on the found device list. Select it and tap Register
button.
5. After done, you can detect any motion around sensor.
Step 4 Add the Smart converter to the Network
1.Open box ③,take out the smart converter
2. Remove the ordinary bulb at your home from the socket, then install the
smart bulb converter into the socket, and power on it.
3. Run the “NEXTURN+” APP, go to “find devices” page, tap “find device”
button, it will appear on the Found Device List. Select it and tap Register
button.
4. After done, you can turn on/ off your lamp with your smart phone.
Step 5 Add the Smart plug to the Network
1.Open box ④,take out the smart plug
2. Plug the Smart plug into a wall outlet to power it.
3. Run the “NEXTURN+” APP, go to “find devices” page, tap “find device”
button, it will appear on the Found Device List. Select it and tap Register
button.
4. After done, you can switch on/off the plug and monitor the data of the
current and power consumption etc.
5
Step 6 Add the door/window sensor to the Network.
1.Open box ⑤,take out the door/window sensor, and get one AAA battery
from box ②
Remarks: The door/window sensor assembly is made up of a main unit and a
magnetic bar.
2. Install one AAA battery into the mains unit.
3. Fix the mains unit to one available location (e.g. the wall), and the stick the
magnetic bar on the opposite location, such as the door or window.
Note: a. When fixing the main unit and the magnetic bar, make sure they
have been aligned in correct direction according to the marked orientation.
b. The normal responding distance between the two parts is no more
than 4mm.
4. Run the “NEXTURN+” APP, go to “find devices” page, tap “find device”
button, it will appear on the Found Device List. Select it and tap Register
button.
5. After done, you can monitor door/window open/close state
Note: To check the energy level of the battery, press the button on the mains
unit. If the LED is on, showing that the battery energy is sufficient; if the LED
fails to light, indicating that the battery has been exhausted, and should be
replaced with a new one.
Step 7 Add the wireless switch to the Network
1. Open box ⑥, take out the wireless switch, and get one AAA battery from
6
box ②
2. Install one AAA battery into the wireless switch
3. Run the “NEXTURN+” APP, go to “find devices” page, tap “find device”
button, it will appear on the Found Device List. Select it and tap Register
button.
4. After done, push down the top housing of the wireless switch to switch the
working status of the designated device.
Step 8 Add the IP Camera to the Network
Open box ⑦,take out the gateway, and get a adapter which use for the
camera in box ②
1. Insert a TF card(4G+,class6+) into slot at camera back.
2. Go to APP store to find “nexturn cam” APP , download and install it
in your smart phone or tablet.
3 .Connect the IP camera to the attached power adapter, then press and
hold down the “Set” button for about5 seconds，The LED blink slowly a few
times, indicating the it is staying in network loading process;
4. Enter the W -LAN settings on your smart phone or tablet, then select the
item “MT5650-XXXXXX” from the list and tap to connect. then run “nexturn
cam” APP, tap , open "camera setup" page.tap , it will get the
camera CID automatically, and chose the WIFI router which smart gateway
has connected to, tap to finish setting.
7
8
Loading...