Yetter 2967-051 User Manual

RESIDUE MANAGER ATTACHMENT

JOHN DEERE MAXEMERGE®2

UNIT MOUNTED

OPERATOR’S MANUAL

YETTER MANUFACTURING CO.
FOUNDED 1930

Colchester, IL 62326-0358
Toll free: 800/447-5777
309/776-3222 (Fax)
Website: www.yetterco.com
E-mail: [e-mail]

FOR

COULTER

PART IDENTIFICATION

FOREWORD

You’ve just joined an exclusive but rapidly
growing club.

For our part, we want to welcome you to the
group and thank you for buying a Yetter product.

We hope your new Yetter implement will help you
achieve both increased productivity and
increased efficiency so that you may generate
more profit. This operator’s manual has been
designed into six major sections.

Foreword, Safety Precautions, assembly
instructions, Operation, parts identification and
troubleshooting.

It is important the owner/operator knows the
implement model number and serial number.
Write the serial and model number in the space
provided and use it in all correspondence when
referring to the implement.

Throughout the manual references may be

made to left side and right side. These

terms are used as viewed from the

operator’s seat facing the front of the tractor.

This SAFETY ALERT SYMBOL indicates

important safety messages in the manual.

When you see this symbol, be alert to the
possibility of PERSONAL INJURY and carefully
read the message that follows.

YETTER MANUFACTURING CO.

309/776-4111
800/447-5777

309/776-3222 (FAX)
Website: www.yetterco.com
E-mail: [e-mail]

WARRANTY POLICY

Yetter Manufacturing warrants all products manufactured and sold by it against defects in material. This warranty being
expressly limited to replacement at the factory of such parts or products as will appear to be defective after inspection.
This warranty does not obligate the Company to bear cost of labor in replacement of parts. It is the policy of the
company to make improvements without incurring obligations to add them to any unit already sold. No warranty is
made or authorized to be made, other than herein set forth. This warranty is in effect for one year after purchase.

Model Number:_________________________

Serial Number:_________________________

Dealer :___________________

The serial and model numbers are located on the top of the left hitch plate.

Yetter Manufacturing warrants its own products only and cannot be responsible for damage to
equipment on which mounted.

2

The word NOTE is used to convey information
that is out of context with the manual text. It
contains special information such as
specifications, techniques, reference information
and other information of a supplementary nature.
The word IMPORTANT is used in the text when
immediate damage will occur to the machine due
to improper technique or operation. Important will
apply to the same information as specified by
note only of an immediate and urgent nature.

It is the responsibility of the user to read the
operator’s manual and comply with the safe and
correct operating procedure and to lubricate and
maintain the product according to the
maintenance schedule in the operator’s manual.

The user is responsible for inspecting his
machine and for having parts repaired or
replaced when continued use of the product
would cause damage or excessive wear to the
other parts.

It is the user’s responsibility to deliver his
machine to the Yetter dealer who sold him the
product for service or replacement of defective
parts that are covered by the warranty policy.

If you are unable to understand or follow the
instructions provided in the publication, consult
you local Yetter dealer or contact:

SAFETY PRECAUTIONS

You can make your farm a safer place to live and work if you observe the safety precautions given. Study
these precautions carefully and insist that those working with you and for you follow them.

Finally, remember this: an accident is usually caused by someone’s carelessness, neglect or oversight.

DANGER

Inspect and replace worn or frayed hydraulic hose, keep all connections tight. Escaping hydraulic fluid
under pressure can have sufficient force to penetrate the skin and cause serious personal injury. Fluid
escaping from a small hole can be almost invisible. Use a piece of cardboard or wood rather than the
hands to search for suspected leaks.

CAUTION

Consult your implement and tractor operator’s manual for correct and safe operating practices. Be aware of
towed implement width and allow safe clearance.

CAUTION: SAFETY SIGNS

Safety decals are placed on the implement to alert the operator and others to the risk of personal injury or
unsafe operation during normal operations and servicing.

1. The safety decals must be kept clean and in good condition to ensure that they are legible.

2. Safety decals must be replaced if they are missing or illegible.

3. When components are replaced during repair or servicing, check that the new components include
the necessary safety signs.

4. Replacement safety decals may be obtained from your local Yetter dealer.

WARNING

Never clean, lubricate or adjust a machine that is in motion. Always install the transport lock pins and bracket when
transporting for any length of time or on public roadways.

If required to service unit in raised position, be sure to install all transport lock pins and locking bracket.

Be sure the implement is securely locked in the 3-point quick hitch before operating.

Do not allow children to operate this equipment.

Do not allow riders on the tractor or implement.

Use speeds and caution dictated by the terrain being traversed. Do not operate on any slope steep enough to cause
tipping or loss of control.

Be sure all personnel are clear of the immediate area before operating.

Read and understand the operator’s manual and require all other persons who will operate the equipment to do the
same.

In operating on public roadways, where legal, be certain all lighting is operating properly and observe all traffic laws.
Ensure slow moving vehicle emblem on tractor is visible.

Beware of increased stopping distances and control effort when operating with implements attached.

Be familiar with all tractor and implement controls and be prepared to stop engine and implements quickly in an
emergency.

FAILURE TO HEED MAY RESULT IN PERSONAL INJURY OR DEATH

3

OPERATION PRECAUTIONS

STOP

Read this before using the Yetter product.

- MACHINE OPERATION

IMPORTANT: failure to properly set the planter frame height and
levelness can result in less than successful operation of the planter
and the Yetter product and may result in damaged equipment.
operators should read and thoroughly understand the instructions
given prior to using the Yetter product.

NOTE: DO NOT use this product if the planter is not adjusted properly!

Leveling the planter:
With the planter lowered to proper operating height (Usually 20”-22”).
Read the planter operator’s manual for recommended setting. Check to
be sure the toolbar and row unit parallel arms are level fore and aft. Re-
check when the planter is in the field and has been fully loaded with seed,
fertilizer, granular chemicals, etc. Also, a field check with a bubble level on
the frame should be made of the hitch height to ensure level operation front
to back.

It is important for the planter to operate level laterally. Tire pressure must be
maintained at pressures specified by the manufacturer.

Field and actual planting conditions change and will dictate planter frame
heights. You must ensure that the row unit parallel arms are approximately
parallel with the ground.

IMPORTANT: For proper operation of the planter attachments and row
units, it is imperative that the planter toolbars and row unit parallel arms be
level side-to-side and front-to-rear. The toolbar frame should operate at a
20”-22” height from the planting surface
operator’s manual for instructions on how to adjust the frame height and
levelness.

. Check the manufacturer’s

All

4

PLANTER ADJUSTMENT

5

BOLT TORQUE

Mounting bolts and hardware

Before operating the Residue Manager for the first time, check to be sure that all
hardware is tight. Check all hardware again after approximately 50 hours of operation
and at the beginning of each planting season.

All hardware used on the Residue Manager is Grade 5 unless otherwise noted. Grade 5
cap screws are marked with three radial lines on the head. If hardware must be replaced,
be sure to replace it with hardware of equal size, strength and thread type. Refer to the
torque values chart when tightening hardware.

Important: Over tightening hardware can cause as much damage as when
under tightening. Tightening hardware beyond the recommended range can
reduce its shock load capacity.

The chart below is a guide for proper torque. Use it unless a specified torque is called out
elsewhere in the manual.
Torque is the force you apply to the wrench handle or the cheater bar, times the length of the
handle or bar.
Use a torque wrench whenever possible.

The following table shows torque in ft. lbs. for coarse thread hardware.

Lubricate all bearings and moving parts as assembled and make certain that they work freely.

WARNING: Never work around the toolbar/implement while in a raised position without using
safety lockups.

CAUTION: The Residue manager attachments are very heavy. Pay extra attention to lifting
techniques while handling and or maneuvering the opener during assembly. Failure to do so may
lead to personal injury.

6

INSTALLATION

1. Remove metric carriage bolt attaching unit coulter to planter on right hand upper

corner of face of casting. Using ½ x 2” bolt, flat washer and locknut supplied,
attach the small pivot bracket to the unit coulter. Do not fully tighten the bolt yet.

2. Remove the two metric carriage bolts on the left hand side of the coulter and then

attach the adjustment bracket with ½ x 2” bolt, ½ x 2” carriage bolt, flat washers
and locknuts (see illustration).

3. The Combo Arm W.A. is attached to the pivot bracket and adjustment bracket with

5/8 x 2” bolts, 9/16” spacers, flat washers and locknuts.

CAUTION: DO NOT USE SPACER STRAP ON COMBO ARM W.A. AS
A HANDLE, FINGERS MAY BE SERIOUSLY INJURED ON SHARP
EDGE OF BLADE, USE ½” SQ. DRIVE SOCKET TOOLS TO ADJUST
THIS PART.

4. Adjust all parts into position and tighten all mounting bolts and check that the unit

coulter is still centered in front of the opener blades.

5. Insert Combo Adjustment into appropriate hole to hold parts in position and

secure with hairpin cotter. *

6. Attach the spoke wheel to the Combo Arm with ‘D’ bolts supplied. Torque 150

ft.lbs.

NOTE: Do not be alarmed if the resulting fitment is not perfectly centered about the
unit coulter blade. It is acceptable for the wheels to be up to ½” off of centered
perfectly.

* In some situations it may be preferable to replace the pin with a bolt and nut
for more secure attachment.

7

RESIDUE MANAGER WHEEL INSTALLATION

1. If you wish to be able to grease the bearings in the hubs, remove the seal from one side of the bearings as
illustrated before assembly. Otherwise the bearings may be left “sealed for life”.

2. When assembling the spoke wheels, bearing assembly and hubcap, be sure to align the grease transfer hole
in the spoke wheel with the groove in the hubcap and hole in the hub to allow grease passage.

3. Install/assemble the spoke wheels, hubs and caps as shown in illustration opposite. IMPORTANT: THE 2527­530 WASHER MUST BE INSTALLED OR THE WHEEL AND HUB ASSEMBLY WILL FALL OFF DURING
USE. TORQUE 150 FT.LBS.

4. If you have chosen to grease the hubs, do so now that the assembly is complete. Approximately 30 pumps
from a lever style gun to fill the hub with grease.

OPERATION

IMPORTANT: For proper operation, the planter frame must operate level (for, aft and side

ROW CLEANER DO’S AND DON’TS

to side) and at the correct height, typically 20”-22”.

1. DO NOT move soil; Residue Managers are designed to move crop residue only.

2. DO NOT operate planter at slow speeds, ground speed affects how aggressive the
spoke wheels are; operate at sufficient speed (4-6 mph) to maintain good residue
flow.

3. DO NOT expect 100% of crop residue to be cleared, it is not necessary and would
necessitate engaging the soil. The width of path cleared depends on ground
conditions, depth setting and ground speed.

4. DO expect to see wheels occasionally quit turning, indicates ideal (shallow) setting
which is not moving soil.

5. DO adjust toolbar frame height 20”-22” and drawbar to “level” correctly. Very

important to ensure planter opener will follow ground contours properly.

8

MAINTENANCE

BEARING ASSEMBLY AND LUBRICATION

Regularly inspect the residue manager for loose or worn parts. Repair and
replace as needed.

Practice Safety

Understand and practice safe service procedures before doing work. Follow ALL the
operating, maintenance and safety information in the equipment operator manual. Clear
the area of bystanders, especially small children, when performing any maintenance or
adjustments. Keep work area clean and dry. Use adequate lighting for the job. Use only
tools, jacks and hoists of sufficient capacity for the job.
Never lubricate, service, or adjust machine while it is moving. Keep hands, feet, and
clothing from power-driven moving and rotating parts. Disengage all power and operate
controls to relieve pressure. Lower equipment to the ground and stop the engine. Remove
the key. Wait for all moving parts to stop before servicing, adjusting, repairing or
unplugging.
Securely support any machine elements with blocks or safety stands that must be raised
for service work.
Keep all parts in good condition and properly installed. Fix damaged equipment
immediately. Replace worn or broken parts. Remove any buildup of grease, oil, or debris.
Make sure all guards are in place and properly secured when maintenance work is
completed.

Assembly

9

MAINTENANCE

NOTE: Be certain to align the grease fitting with the slot in the wheel and the hubcap so

that the grease can flow freely.

IMPORTANT: THE 2527-530 WASHER MUST BE INSTALLED OR THE WHEEL
AND HUB ASSEMBLY WILL FALL OFF DURING USE.

10

MAINTENANCE

Grease must fill this

Hubcap cavity.

11

MAINTENANCE

Lubrication

CAUTION: To help prevent serious injury or death to you or others caused by
unexpected movement, service machine on a level surface. Lower machine to
ground or sufficiently lock or block raised machine before servicing. If machine
is connected to tractor, engage parking brake and place transmission in
"PARK", shut off engine and remove key. If machine is detached from tractor,
block wheels and use shop stands to prevent movement.

CAUTION: Do not clean, lubricate, or adjust machine while in motion.

Use grease based on NLGI consistency numbers and the expected air temperature range
during the service interval.
Use a multi-purpose lithium, water resistant, moderate speed, and NLGI grade #2
grease.
Other greases may be used if they meet the following NLGI Performance

Classification: GC-LB

IMPORTANT: Some types of grease thickener are not compatible with others.
Consult your grease supplier before mixing different types of grease.

Alternative Lubricants

Conditions in certain geographical areas may require special lubricants and lubrication
practices which do not appear in the operator's manual. If there are any questions,
consult Yetter Manufacturing Co. to obtain latest information and recommendation.

PART # DESCRIPTION

OUNCES OF GREASE

2967-404 13” TAPER TOOTH R.M. WHEEL 1.12 OZ
2967-602 13” SHARK TOOTH R.M. WHEEL 1.12 OZ
2967-186 FLOATER WHEEL KIT W/R.M. WHEEL 2.08 OZ
2967-596 HEAVY DUTY OR BEVEL R.M. WHEEL W/

FLOATER WHEEL KIT

2.40 OZ

Storing Lubricants

Your machine can operate at top efficiency only if clean lubricants are used.
Use clean containers to handle all lubricants.
Store them in an area protected from dust, moisture and other contaminants.

12

MAINTENANCE

Lubrication Symbols

Lubricate with grease at hourly interval indicated on symbol.

Lubrication Intervals

IMPORTANT: The recommended service intervals are based on normal conditions;

severe or unusual conditions may require more frequent lubrication.

Perform each lubrication and service procedure at the beginning and end of each season.

Clean grease fittings before using grease gun, to avoid injecting dirt and grit into the
bearing. Replace any lost or broken fittings immediately. If a fitting fails to take grease,
remove and clean thoroughly, replace fitting if necessary. Also check for failure of
adjoining parts.

BEARING REPLACEMENT INSTALLATION

5. If you wish to be able to grease the bearings in the hubs, remove the seal from one
side of the bearings as illustrated before assembly. Otherwise the bearings may
be left “sealed for life”.

6. When assembling the spoke wheels, bearing assembly and hubcap, be sure to
align the grease transfer hole in the spoke wheel with the groove in the hubcap
and hole in the hub to allow grease passage.

7. Install/assemble the wheels, hubs and caps. IMPORTANT: THE 2527-530
WASHER MUST BE INSTALLED OR THE WHEEL AND HUB ASSEMBLY WILL
FALL OFF DURING USE.

8. Grease the wheel/hub/bearing assembly.

13

MAINTENANCE

Storing the Equipment

Store the machine in an area away from human activity

Store machine in RAISED position.

Install service locks on all wheel cylinders.

At the end of the season, the machine should be thoroughly inspected and prepared for
storage. Repair or replace any worn or damaged components to prevent down time at the
start of the next season. Store machine under cover with all parts in operating condition.

• Clean machine thoroughly to remove all dirt, debris and crop residue, which would
hold moisture and cause rusting.

• Inspect machine for worn or broken parts. See your Yetter Farm Equipment dealer
during the off-season so that parts or service can be acquired when machine is not
needed in the field.

• Lubricate bearings as outlined in the Lubrication section

• Paint all parts which are chipped or worn and require repainting.

• Store machine in a clean, dry place with the planting unit out of the sun.

• If the machine cannot be stored inside, cover with a waterproof tarpaulin and tie

securely in place.

• Do not allow children to play on or around the machine

14

RESIDUE MANAGER WHEELS

15

PARTS IDENTIFICATION

16

PARTS IDENTIFICATION

17

NOTES:

18

NOTES:

19

Our name

Is getting known

Just a few years ago, Yetter products were sold primarily to the
Midwest only. Then we embarked on a program of expansion and
moved into the East, the South, the West and now north into Canada.
We’re even getting orders from as far away as Australia and Africa.

So, when you buy Yetter products . . .you’re buying a name that’s
recognized. A name that’s known and respected. A name that’s
become a part of American agriculture and has become synonymous
with quality and satisfaction in the field of conservation tillage.

Thank you.

YETTER MANUFACTURING CO.

Colchester, IL 62326-0358 • 309/776-4111

Toll Free 800/447-5777

Fax [phone]
Website: WWW.YETTERCO.COM
E-MAIL: [e-mail]

2565-354_REV_B • 06/09

20