Yetter 2967-024 User Manual

RESIDUE MANAGER

CNH PLANTER UNITS

OPERATOR’S MANUAL

PART IDENTIFICATION

YETTER MANUFACTURING CO.
FOUNDED 1930

Colchester, IL 62326-0358
Toll free: 800/447-5777
309/776-3222 (Fax)
Website: www.yetterco.com
E-mail: [e-mail]

TITAN

FOR

2967-023/024

FOREWORD

You’ve just joined an exclusive but rapidly
growing club.

For our part, we want to welcome you to the
group and thank you for buying a Yetter product.

We hope your new Yetter products will help you
achieve both goals-increase your productivity and
increase your efficiency so that you may generate
more profit.

This operator’s manual has been designed into
four major sections: Foreword, Safety
Precautions, Installation Instructions and Parts
Breakdown.

This SAFETY ALERT SYMBOL

indicates important safety messages in

the manual. When you see this

symbol, be alert to the possibility of

PERSONAL INJURY and carefully

read the message that follows.

The word NOTE is used to convey information
that is out of context with the manual text. It
contains special information such as
specifications, techniques and reference
information of a supplementary nature.

The word IMPORTANT is used in the text when
immediate damage will occur to the machine due

to improper technique or operation. Important will
apply to the same information as specified by
note only of an immediate and urgent nature.

It is the responsibility of the user to read the
operator’s manual and comply with the safe and
correct operating procedure and to lubricate and
maintain the product according to the
maintenance schedule in the operator’s manual.

The user is responsible for inspecting his
machine and for having parts repaired or
replaced when continued use of the product
would cause damage or excessive wear to the
other parts.

It is the user’s responsibility to deliver his
machine to the Yetter dealer who sold him the
product for service or replacement of defective
parts, which are covered by the warranty policy.

If you are unable to understand or follow the
instructions provided in this publication, consult
your local Yetter dealer or contact:

YETTER MANUFACTURING CO.

309/776-4111
800/447-5777

309/776-3222 (FAX)
Website: www.yetterco.com
E-mail: [e-mail]

WARRANTY

Yetter Manufacturing warrants all products manufactured and sold by it against defects in material. This
warranty being expressly limited to replacement at the factory of such parts or products as shall appear to
be defective after inspection. This warranty does not obligate the Company to bear cost of labor in
replacement of parts. It is the policy of the Company to make improvements without incurring obligations to
add them to any unit already sold. No warranty is made or authorized to be made, other than herein set
forth. This warranty is in effect for one year after purchase.

DEALER: ________________________________________

Yetter Manufacturing warrants its own products only and cannot be responsible for damages to
equipment on which mounted.

2

TABLE OF CONTENTS

Introduction…………………………………………………………..pg.2
Warranty……………………………….……………………………..pg.2
Table of Contents……………………………………………………pg.3
Optional Equipment………………………………………………….pg.3
Safety Information…………………………………………………...pg.4
Bolt Torque…………………………………………………………...pg.5
Use Guide/Troubleshooting………………………………………...pg.6-7

Installation Instruction……..…….………………..…………..…….pg.8-10
Operation……………………………...……………………………..pg.11
Maintenance………………………..………………………………..pg.12-17

Parts Identification………………………………..………….……...pg.18-19

OPTIONAL EQUIPMENT

2967-186 FLOATER WHEEL

L.H. ASSEMBLY SHOWN

(2) REQUIRED PER ROW

3

SAFETY

A brief description of signal words that may be used in this manual:

CAUTION: Used as a general reminder of good safety practices or to direct attention to unsafe practices.

WARNING: Denotes a specific potential hazard.

DANGER: Denotes the most serious specific potential hazard.

SAFETY PRECAUTIONS

You can make your farm a safer place to live and work if you observe the safety precautions given. Study
these precautions carefully and insist that those working with you and for you follow them.

Finally, remember this: an accident is usually caused by someone’s carelessness, neglect or oversight.

WARNING

Never clean, lubricate or adjust a machine that is in motion. Always lower or block the implement before
performing service.

If the machine must be serviced in the raised position, jack or block it up to prevent it from accidentally
falling and injuring someone.

Do not allow riders on the tractor or implement.

Use speeds and caution dictated by the terrain being traversed. Do not operate on any slope steep enough
to cause tipping or loss of control.

Be sure all personnel are clear of the immediate area before operating.

Read and understand the operator’s manual and require all other persons who will operate the equipment
to do the same.

Be familiar with all tractor and implement controls and be prepared to stop engine and implements quickly in
an emergency.

CAUTION

Consult your implement and tractor operator’s manual for correct and safe operating practices.

Beware of towed implement width and allow safe clearance.

FAILURE TO HEED MAY RESULT IN PERSONAL INJURY OR DEATH.

4

BOLT TORQUE

Mounting bolts and hardware

Before operating the Titan Residue Manager for the first time, check to be sure that all
hardware is tight. Check all hardware again after approximately 50 hours of operation
and at the beginning of each planting season.

All hardware used on the Titan Residue Manager is Grade 5 unless otherwise noted.
Grade 5 cap screws are marked with three radial lines on the head. If hardware must be
replaced, be sure to replace it with hardware of equal size, strength and thread type.
Refer to the torque values chart when tightening hardware.

Important: Over tightening hardware can cause as much damage as when
under tightening. Tightening hardware beyond the recommended range can
reduce its shock load capacity.

The chart below is a guide for proper torque. Use it unless a specified torque is called out
elsewhere in the manual.
Torque is the force you apply to the wrench handle or the cheater bar, times the length of the
handle or bar.
Use a torque wrench whenever possible.

The following table shows torque in ft. lbs. for coarse thread hardware.

Lubricate all bearings and moving parts as assembled and make certain that they work freely.

WARNING: Never work around the toolbar/implement while in a raised position without using
safety lockups.

CAUTION: The Residue manager attachments are very heavy. Pay extra attention to lifting
techniques while handling and or maneuvering the opener during assembly. Failure to do so may
lead to personal injury.

5

OPERATION/USE GUIDE/TROUBLESHOOTING

IMPORTANT: Please check the amount of travel that the planter row unit has

before going to the field to plant.

NOTE: The recommended height of a level planter toolbar frame is 20”-22”. Always

visually check seed spacing and depth-calibrate your equipment if necessary.

Figure A. – The planter hitch and frame are both 20” off the ground. To ensure this, visually check to see

that the planter boxes are level and that the planter unit parallel arms are also parallel with the ground.

When using planter attachments located in front of the planter unit, this setting is very important.

Figure B. – The planter hitch is set too low while the planter frame remains at 20” off the ground! Notice

from the illustration that the unit mounted coulter is running deeper in the ground than the planter unit. This
condition can result in the formation of an air pocket below the seedbed, which will in turn dramatically
decrease seed growth.

NOTE: Both illustrations are strictly for reference only. They are intended to show that
proper adjustment of the hitch height is critical. Consult your planter operator’s manual for the
proper height adjustment of the hitch.

6