Yetter 2967-014 User Manual

TITAN SERIES

2967-013/2967-014

NARROW ROW SHORT U.N.T.™

RESIDUE MANAGER

OPERATOR’S MANUAL

PART IDENTIFICATION

2565-748_REV_E – 02/14

YETTER MANUFACTURING CO.
FOUNDED 1930

Colchester, IL 62326-0358
Toll free: 800/447-5777
309/776-3222 (Fax)
Website: www.yetterco.com
E-mail: [e-mail]

FOREWORD

You’ve just joined an exclusive but rapidly
growing club.

For our part, we want to welcome you to the
group and thank you for buying a Yetter product.

We hope your new Yetter products will help you
achieve both goals-increase your productivity and
increase your efficiency so that you may generate
more profit.

This operator’s manual has been designed into
four major sections: Foreword, Safety
Precautions, Installation Instructions and Parts

Breakdown.

This SAFETY ALERT SYMBOL

indicates important safety
messages in the manual. When you see this
symbol, be alert to the possibility of PERSONAL
INJURY and carefully read the message that
follows.

The word NOTE is used to convey information
that is out of context with the manual text. It
contains special information such as
specifications, techniques and reference
information of a supplementary nature.

The word IMPORTANT is used in the text when
immediate damage will occur to the machine due

WARRANTY

Yetter Manufacturing warrants all products manufactured and sold by it against defects in material. This
warranty being expressly limited to replacement at the factory of such parts or products as shall appear to be
defective after inspection. This warranty does not obligate the Company to bear cost of labor in replacement of
parts. It is the policy of the Company to make improvements without incurring obligations to add them to any
unit already sold. No warranty is made or authorized to be made, other than herein set forth. This warranty is
in effect for one year after purchase.

DEALER: ________________________________________

Yetter Manufacturing warrants its own products only and cannot be responsible for damages to
equipment on which mounted.

2

to improper technique or operation. Important will
apply to the same information as specified by
note only of an immediate and urgent nature.

It is the responsibility of the user to read the
operator’s manual and comply with the safe and
correct operating procedure and to lubricate and
maintain the product according to the
maintenance schedule in the operator’s manual.

The user is responsible for inspecting his
machine and for having parts repaired or
replaced when continued use of the product
would cause damage or excessive wear to the
other parts.

It is the user’s responsibility to deliver his
machine to the Yetter dealer who sold him the
product for service or replacement of defective
parts, which are covered by the warranty policy.

If you are unable to understand or follow the
instructions provided in this publication, consult
your local Yetter dealer or contact:

YETTER MANUFACTURING CO.

309/776-4111
800/447-5777

309/776-3222 (FAX)

Website: www.yetterco.com

E-mail: [e-mail]

3

TABLE OF CONTENTS

Introduction……………………………………………………………….……2

Warranty……………………………….……………………………………....2

Safety…………………………………………………………………………..3
Table of Contents……………………………………………………………..4
Optional Equipment…………………………………………………………..4
Bolt Torque…………………………………………………………………….5
Installation Instruction……..…….………………..…………..……..…...6-10
Operation…………………………………………………………………11-13

Maintenance……………………………………………………………..14-19

Parts Identification………………………………..………….…….…....20-21

OPTIONAL EQUIPMENT

2967-186 FLOATER WHEEL

L.H. ASSEMBLY SHOWN

(2) REQUIRED PER ROW

4

BOLT TORQUE

Mounting bolts and hardware

Before operating the Titan Residue Manager for the first time, check to be sure that all
hardware is tight. Check all hardware again after approximately 50 hours of operation and
at the beginning of each planting season.

All hardware used on the Titan Residue Manager is Grade 5 unless otherwise noted.
Grade 5 cap screws are marked with three radial lines on the head. If hardware must be
replaced, be sure to replace it with hardware of equal size, strength and thread type. Refer
to the torque values chart when tightening hardware.

Important: Over tightening hardware can cause as much damage as when under
tightening. Tightening hardware beyond the recommended range can reduce its shock load
capacity.

The chart below is a guide for proper torque. Use it unless a specified torque is called out
elsewhere in the manual.
Torque is the force you apply to the wrench handle or the cheater bar, times the length of the
handle or bar.
Use a torque wrench whenever possible.

The following table shows torque in ft. lbs. for coarse thread hardware.

Lubricate all bearings and moving parts as assembled and make certain that they work freely.

WARNING: Never work around the toolbar/implement while in a raised position without using safety
lockups.

CAUTION: The Titan Residue Manager attachments are very heavy. Pay extra attention to lifting
techniques while handling and or maneuvering the opener during assembly. Failure to do so may lead
to personal injury.

5

INSTALLATION INSTRUCTIONS

2967-013

STEP 1. Attach the 2966-200 mount bracket to the planter unit using 3) ½” bolts and lock

nuts.

6

INSTALLATION INSTRUCTIONS

2967-014 NARROW TITAN FOR CNH

STEP 1A. Attach the mount bracket to the planter row unit using: 2) ½” bolts and lock nuts.

7

INSTALLATION INSTRUCTIONS

STEP 2.

335 bushing, 2967-639 adjustment plate and lock nut. On the right side use a 5/8” x 2” bolt, 6000­335 bushing, flat washer and lock nut. Install the ½” x 2” bolt, 2967-622 spacer and lock nut on the
left side to secure the adjustment plate and insert the 2984-326 pin in the adjustment holes and
install the 2570-448 hairpin clip.

Attach the narrow arm to the mount bracket on the left side using a 5/8” x 2” bolt, 6000-

8