Yetter 2940 Short Floating Air Adjust Residue Manager User Manual

Loading...

2940 AIR ADJUST RESIDUE MANAGER

OPERATOR’S MANUAL PART IDENTIFICATION

2565-773_REV_C 03/2014

*Patent Pending

YETTER MANUFACTURING CO.

FOUNDED 1930

Colchester, IL 62326-0358 Toll free: 800/447-5777

309/776-3222 (Fax) Website: www.yetterco.com E-mail: info@yetterco.com

FOREWORD

You’ve just joined an exclusive but rapidly growing club.

For our part, we want to welcome you to the group and thank you for buying a Yetter product.

We hope your new Yetter products will help you achieve both goals-increase your productivity and increase your efficiency so that you may generate more profit.

This operator’s manual has been designed into four major sections: Foreword, Safety Precautions, Installation Instructions and Parts Breakdown.

This SAFETY ALERT SYMBOL indicates important safety messages in the manual. When you see this symbol, be alert to the possibility of

PERSONAL INJURY and carefully read the message that follows.

The word NOTE is used to convey information that is out of context with the manual text. It contains special information such as specifications, techniques and reference information of a supplementary nature.

The word IMPORTANT is used in the text when immediate damage will occur to the machine due

to improper technique or operation. Important will apply to the same information as specified by note only of an immediate and urgent nature.

It is the responsibility of the user to read the operator’s manual and comply with the safe and correct operating procedure and to lubricate and maintain the product according to the maintenance schedule in the operator’s manual.

The user is responsible for inspecting his machine and for having parts repaired or replaced when continued use of the product would cause damage or excessive wear to the other parts.

It is the user’s responsibility to deliver his machine to the Yetter dealer who sold him the product for service or replacement of defective parts, which are covered by the warranty policy.

If you are unable to understand or follow the instructions provided in this publication, consult your local Yetter dealer or contact:

YETTER MANUFACTURING CO.

309/776-4111 800/447-5777 309/776-3222 (FAX) Website: www.yetterco.com E-mail: info@yetterco.com

WARRANTY

Yetter Manufacturing warrants all products manufactured and sold by it against defects in material. This warranty being expressly limited to replacement at the factory of such parts or products as shall appear to be defective after inspection. This warranty does not obligate the Company to bear cost of labor in replacement of parts. It is the policy of the Company to make improvements without incurring obligations to add them to any unit already sold. No warranty is made or authorized to be made, other than herein set forth. This warranty is in effect for one year after purchase.

DEALER: ________________________________________

Yetter Manufacturing warrants its own products only and cannot be responsible for damages to equipment on which mounted.

2

SAFETY

A brief description of signal words that may be used in this manual:

CAUTION: Used as a general reminder of good safety practices or to direct attention to unsafe practices.

WARNING: Denotes a specific potential hazard.

DANGER: Denotes the most serious specific potential hazard.

SAFETY PRECAUTIONS

You can make your farm a safer place to live and work if you observe the safety precautions given. Study these precautions carefully and insist that those working with you and for you follow them.

Finally, remember this: an accident is usually caused by someone’s carelessness, neglect or oversight.

WARNING

Never clean, lubricate or adjust a machine that is in motion. Always lower or block the implement before performing service.

If the machine must be serviced in the raised position, jack or block it up to prevent it from accidentally falling and injuring someone.

Do not allow riders on the tractor or implement.

Use speeds and caution dictated by the terrain being traversed. Do not operate on any slope steep enough to cause tipping or loss of control.

Be sure all personnel are clear of the immediate area before operating.

Read and understand the operator’s manual and require all other persons who will operate the equipment to do the same.

Be familiar with all tractor and implement controls and be prepared to stop engine and implements quickly in an emergency.

CAUTION

Consult your implement and tractor operator’s manual for correct and safe operating practices.

Beware of towed implement width and allow safe clearance.

FAILURE TO HEED MAY RESULT IN PERSONAL INJURY OR DEATH.

3

TABLE OF CONTENTS

Introduction……….…………………………………………………………...2

Warranty….…………………………………….……………………………...2

Safety Information.…………………………………………………………....3

Table of Contents……….…………………………………………………….4

Bolt Torque………..….……………………………………………………….5

2940 Air Adjust Components, Kits, Accessories………………………..6-9

Installation Instruction….………..…….………………..…………..…..10-46

Operation…..……………………………...…………………………...…47-58

Maintenance….……………………………..…...……………………….59-65

Parts Identification…….…………...…………………..………….…......66-82

Trouble Shooting………………………….……………………………........83

4

BOLT TORQUE

Mounting bolts and hardware

All hardware used on the 2940 Air Adjust is Grade 5 unless otherwise noted. Grade 5 cap screws are marked with three radial lines on the head. If hardware must be replaced, be sure to replace it with hardware of equal size, strength and thread type. Refer to the torque values chart when tightening hardware.

Important: Over tightening hardware can cause as much damage as when under tightening. Tightening hardware beyond the recommended range can reduce its shock load capacity.

The chart below is a guide for proper torque. Use it unless a specified torque is called out elsewhere in the manual.

Torque is the force you apply to the wrench handle or the cheater bar, times the length of the handle or bar.

Use a torque wrench whenever possible.

The following table shows torque in ft. lbs. for coarse thread hardware.

5

2940 AIR ADJUST

Components, Kits, Accessories, & Ordering Numbers

Residue Manager Kits

2940-001 Pneumatic Assembly with choice of wheel kit 2940-002 Pneumatic Narrow Assembly with choice of wheel kit 2940-003 Pneumatic CNH Assembly with choice of wheel kit

2940-004 Pneumatic CNH Narrow Assembly with choice of wheel kit

Control Kits

2940-050 Pneumatic Compressor Kit

 

 

2940-053 Pneumatic Less Tank and Compressor Kit

 

Air Lines and Wiring Kits

For 2940-050 Kit

 

2940-065

 

8 Row—20’ wiring and tubing kit

 

2940-066

 

12

Row—30’ wiring and tubing kit

 

2940-067

 

16

Row—40’ wiring and tubing kit

 

2940-068

 

16

Row—48’ wiring and tubing kit

 

2940-069

 

24

Row—60’-66’ wiring and tubing kit

 

2940-070

 

36

Row—80’-90’ wiring and tubing kit

 

2940-071

 

48

Row—120’ wiring and tubing kit

 

2940-072

 

Split Row/Interplant Kit

 

2940-073

 

Center Tube Extension Kit

 

Air Lines and Wiring Kits

For 2940-053 Kit

 

2940-075

 

8-12 Row--

20/30’ NON-ISO Hydraulic Wiring and Tubing Kit

2940-076

 

16

Row---40/44’ NON ISO Hydraulic Wiring and Tubing Kit

2940-077

 

16-24 Row--

48/60/66’ NON ISO Hydraulic Wiring and Tubing Kit

2940-078

 

36-48 Row---

80/90/120’ NON ISO Hydraulic Wiring and Tubing Kit

2940-079

 

Switch Panel Resisted Adapter-----------------------------

 

2940-083

 

8”X12”/8”X16” Bar Mount Kit for 2940-103

2940-084

 

Universal Hand Rail Mount Kit for 2940-103

2940-085

Compressor Mount Bracket Two Point Hitch Kit for 2940-101

2940-086

Compressor Mount Bracket Draft Tube Kit or Universal Kit for 2940-101

2940-112

VDM 12 Volt Controller

 

 

2940-113

RAM Cab Controller Mount Kit--------------------------------------

 

2940-147

Tee Kit (10 Pieces)

 

 

 

2940-150

Compressor Main Power Cable, 80A Breaker------------------

 

2940-151

10’ Compressor Main Power Cable Extension, 4 Gauge----

 

2940-152

Hitch to switch panel CAN Cable-----------------------------------

 

2940-153

Ignition, power/ground to switch panel (controller)-------------

 

6

 

 

 

 

 

2940 AIR ADJUST

Components, Kits, Accessories, & Ordering Numbers (CON’T)

2940-154

30’

Dump Valve Cable Black----------------------------------------

 

2940-155

30’

Dump Valve Cable White

 

2940-156

15’ Dump Valve Cable Black------------------------------------------

 

2940-157

15’ Dump Valve Cable White

 

2940-158

3” Y Harness Black Connector---------------------------------------

 

2940-159

3” Y Harness White Connector

 

2940-160

5’ Dump Valve Cable White

 

2940-161

5’ Dump Valve Cable Black-------------------------------------------

 

2940-162

Dump Valve Cable Compressor Connector----------------------

 

2940-163

20’ Main Power Extension---------------------------------------------

 

2940-164

5’ CAN AUX to Air Assembly

 

2940-165

10’ CAN AUX to Air Assembly---------------------------------------

 

2940-166

VDM Power Cable 40A Breaker, 8 Gauge------------------------

 

2940-167

10’ VDM Power Cable Extension------------------------------------

 

2940-168

20’ VDM Power Cable Extension, 8 Gauge-----------------------

 

7

2940 AIR ADJUST

Components, Kits, Accessories, & Ordering Numbers (CON’T)

2940-169

10’ Cab to Hitch Extension-----------------------------------------------

 

 

2940-170

10’ Can Aux to Air Assembly Extension------------------------------

 

2940-171

30’ Can Aux to Air Assembly Extension

 

2940-336

Dump Valve------------------------------------------------------------------

 

 

 

PART NUMBER

 

A

B

C

DESCRIPTION

 

 

 

 

 

 

3/8 PUSH CONNECT ELBOW

 

 

 

 

 

1/8 NPT MALE-----------------

 

 

 

1/8

 

 

 

 

2940-337

 

NPT

3/8 PCT

 

 

 

 

 

3/8

 

 

 

 

2940-338

 

NPT

3/8 PTC

3/8 PTC

3/8 PUSH CONNECT TEE--

 

 

 

1/8

 

 

3/8 PUSH CONNECT

 

2940-339

 

NPT

3/8 PTC

 

STRAIGHT 1/8 NPT MALE

2940-341

 

 

 

 

TUBING CUTTER-----

 

2940-342

 

 

 

 

BALL VALVE--------

 

8

2940 AIR ADJUST

3/8" OD,TUBING, BLACK

PART NUMBER

QTY (FT)

PACKAGE

2940-345

100

COIL

3/8" OD, TUBING, BLUE

PART NUMBER

QTY (FT)

PACKAGE

2940-346

100

COIL

2940-357

Extreme Air Magnum Compressor Rebuild Kit

2940-367

3/8”OD 250PSI Working Pressure Tubing 25FT Roll

2940-390

Extreme Air Magnum Compressor with Filter Kit

2940-395

Filter Element/Compressor-----------------------------------------

 

2940-396

Filter Pre-Cleaner-Compressor------------------------------------

 

2940-430

20FT CAN AUX to Air Assembly Extension

 

9

SYSTEM REQUIREMENTS

POWER SUPPLY

The 2940 system uses a switched power source. The 2940-153 will need connected to a switched power source. (Connector to the tractor not included)

SWITCHED POWER SOURCE CONNECTOR PART #’S:

JOHN DEERE P/N: RE67013

CNH P/N: 187103A1

FUSE PROTECTION

To protect the Compressor Assembly from damage always ensure the integrity of the integrated 40 amp and/or 80 amp circuit breaker at the tractor cable where connected to the battery in case of short or over-circuit. When connected correctly, the tractor has a fuse to protect the cab controller located in the tractor’s fuse panel.

AIR COMPRESSOR MAINTENANCE

To prolong life expectancy of compressor, clean filter by removing the element from the housing, and tapping it, exposed side down. This will empty the pleats of the filter of collected dust. If the dust has been wet or will not clean out, call Yetter to order a new element. You may lightly blow out the electronic box using an air tool. The housing and filter should be checked every two days of field operation, or more if conditions are very dusty.

FAILURE TO LINE UP TABS WHEN PLUGGING MALE INTO FEMALE CONNECTORS CAN RESULT IN SHORT CIRCUIT

10

2940 AIR ADJUST SYSTEM INFORMATION

The 2940 Air Adjust Residue Manager control system consists of five primary components and kits. These parts include; the Cab Controller, the Air Compressor Assembly, Residue Manager Kit, Tank Mounting Kit and the necessary Wires, Air Lines, and Fittings.

CAB CONTROLLER____________________________________________________________

2940-100

The Cab Controller will use the RAM mount provided for installation in cab. Make adjustments quickly and accurately during planting with the cab controller.

Adjust up and down pressure to create the ideal “ride” or floating position for residue managers. Lift and down pressure settings can be adjusted independently. Down pressure can be increased to fix row cleaner in the rigid position. Five presets can be programmed within the controller for quick changes. Residue Managers can be raised as needed with a push of a button.

AIR COMPRESSOR ASSEMBLY_________________________________________________

2940 Air Adjust requires a stable air supply source that can provide 105 psi of clean, dry air. The ‘clean, dry air’ is a key component of the air supply, moisture within the air supply can shorten the life-cycle of the system.

11

2940 AIR ADJUST SYSTEM INFORMATION

RESIDUE MANAGER__________________________________________________________

WIRE, LINES, AND FITTINGS KIT_____________________________________________

12V-DC cables will be used to power the air compressor, cab control, and dump valves. Flexible tubing will be used to move air from the tank to each air bag. Each kit will include pneumatic lines for both circuits, down and lift, as well as the fittings to make

connections and cable ties to securely fasten the lines to the planter.

Note: All 2940 Air Adjust kits include a tubing cutter within the kit.

The 2940-341 cutter should be used for every cut to ensure a clean, square cut.

12

2940 AIR ADJUST SYSTEM INFORMATION

________________________CAB CONTROLLER SERIAL #______________________

Serial # is located on the back of the Cab control. See photo below.

Serial Number Location

Serial # is located on the front of VDM in the compressor assembly. See photo below.

13

2940 AIR ADJUST ASSEMBLY GUIDE OUTLINE

STEP 1: INSTALLING 2940-100 CONTROLLER

Begin by installing the 2940 Air Adjust by mounting the 2940-100 Cab Controller and 2940-133 RAM Mount within the cab of the tractor. Position the Cab Controller within reach during operation without compromising safety or visibility from the cab. Route the 2940-152 cable from the hitch connecting point to the switch panel. Refer to page 15.

STEP 2: INSTALLING COMPRESSOR ASSEMBLY AND POWER SUPPLY CABLES

Begin by locating a suitable mounting location for the compressor assembly. Placement of the compressor assembly will vary on the make and model of the planter. Use mounts supplied or depending on application, different mounts may need to be built. NOTE: Be sure to check clearance of compressor assembly in all locations, especially noting tractor tires and folding/unfolding the planter for transport mode and 2-point top link.

Next, if using the 2940-101 compressor, connect the 2940-150 Compressor Power Cable and 2940-166 VDM Power Cable on the 12V power source from the tractor battery. If using the 2940103, only the 2940-166 VDM Power Cable will be required to be installed on the 12V power source. After cables are properly installed on 12V power source, safely route the power cables to the rear of the tractor in a manner to protect the cables from heat and any pinch points, securing at rear of tractor. Refer to pages 16-25

STEP 3: RESIDUE MANAGER INSTALLATION

Install the 2940-140 Residue Manager Assembly, securing with mounting hardware and then install Wheel Mount Assemblies.

For conventional or larger planters upper holes may be needed. For very shallow planting depths, lower hole settings may need to be used. Refer to the diagram on pages 26-28.

STEP 4: CONNECTING & ROUTING AIR LINES

Install the air lines, down (black) and lift (blue) pressure circuits, to the Air Bags. Route the air lines safely from the Air Bags, avoiding rotating parts and pinch points, then connect to the trunk lines on the planter frame. Route the main trunk line in the direction of the compressor unit to connect with to the Compressor Assembly. Refer to pages 29-45.

STEP 5: DUMP VALVE INSTALLATION

Install the dump valves to the planter as shown in the diagram. Install the wiring harness; route the wiring harness safely from dump valves to the Compressor unit, avoiding rotating parts and pinch points. Refer to page 46.

STEP 6: PERFORM A PRE-OP TEST OF THE SYSTEM

Now that the system is set up, perform a test of the system. Before performing a test, make sure to fully unfold your planter. Begin a Compressor test, Wiring and Plumbing test, and a Leak test on your system. Refer to page 47.

14

INSTALLING THE CAB CONTROLLER

Step 1: Begin installing the 2940 Air Adjust controller once an adequate mounting location has been found, fix the base component of the 2940-113 Mounting Bracket in place. Connect the mount bracket to the rear of the controller.

Step 2: Attach the male end 2 pin connector of the 2940-153 to the female end 2 pin connector on the 2940-100 cab controller. Install connector not provided for your tractor at the bare end of the 2940-153 and connect to tractors switched power source. The cigarette outlet is NOT a switched port on all models of tractors, and therefore should not be used.

Convenience port connector part #’s:

JOHN DEERE PART #: RE67013

CNH PART #: 187103A1

Step 3: Route the 2940-152 hitch to switch panel

wire harness from the rear 6 pin connector of the 2940-100 cab controller to the hitch-point at the rear of the

tractor.

15

INSTALLING 2940 AIR COMPRESSOR ASSEMBLY

Begin by mounting the 2940 Compressor:

Step 1: Every planter/tractor combination will contain its own unique situations in regard to mounting the 2940 Compressor Assembly for clearance and accessibility.

YOU SHOULD EXERCISE YOUR OWN BEST JUDGEMENT TO FIT YOUR SITUATION.

Begin by locating a suitable mounting location for the compressor assembly. Placement of the compressor assembly will vary on the make and model of the planter. Use mounts supplied or depending on application different mounts may need to be built. NOTE: Be sure to check clearance of compressor assembly in all locations, especially noting tractor tires and folding/unfolding the planter for transport mode and 2-point top link.

Next, if using the 2940-101 compressor, connect the 2940-150 Compressor Power Cable and 2940-166 VDM Power Cable on the 12V power source from the tractor battery. If using the 2940-103, only the 2940-166 VDM Power Cable will be required to be installed on the 12V power source. After cables are properly installed on 12V power source, safely route the power cables to the rear of the tractor in a manner to protect the cables from heat and any pinch points, securing at rear of tractor. The 2940 Air Compressor Assembly requires mounting with access to 12V power from the tractor. Optional power cable extensions are available.

Step 2: Visually inspect the proposed mounting location for structural stability and to find signs of wear in that location. Possible obstructions to be aware of include marker arms, liquid fertilizer tanks, rear tires (duals especially) during tight turns, etc…

Step 3: Mark out the position of the Compressor then complete a cycle of folding/unfolding to transport mode and raising/lowering of the planter; as well as, driving in a tight circle in one or both directions, in planting position, to verify or identify obstructions.

Step 4: Once the compressor is mounted, repeat the previous process very cautiously to once again verify that the compressor is clear of obstructions.

Use the illustration with dimensions to identify possible mounting locations on your

specific planter. Both the 2940-101 and 2940-103 require 4” of clearance from each side. (top, bottom, front, back, both sides)

16

INSTALLING 2940 COMPRESSOR ASSEMBLY 2940 AIR COMPRESSOR MOUNTING GUIDE

2940-085 mounting kit is designed for mounting to the 2 point cross hitch on the planter, or require greater elevation of the compressor for clearance reasons.

The most common mounting location for larger planters will be on the draft bar. Use the 2940-086 mounting kit for situations that require mounting elsewhere on the planter than the hitch. This will allow the compressor to be elevated and set back (or forward) to avoid clearance issue.

REFER TO PAGE 77 & 78 FOR PART LIST

17

2940-101 External Lay Out

A.LATCHES (2940-307) FOR CLOSING AIR COMPRESSOR HOUSING LID

B.WHEEL TRACK DOWN PRESSURE PORT- ROUTE BLACK AIR TUBING FROM THE WT PORT TO THE DOWN PRESSURE DUMP VALVE ON CENTER ROWS OF THE PLANTER. THE DOWN PRESSURE PSI ON THE CENTER SECTION RESIDUE MANAGERS CAN BE ADJUSTED SEPARATELY FROM THE WING SECTION RESIDUE MANAGERS DOWN PRESSURE PSI. IF THE WT PORT IS NOT USED, INSTALL THE 2940-352 PLUG TO PREVENT AIR LOSS.

C.RESIDUE DOWN PRESSURE PORT-ROUTE BLACK AIR TUBING FROM THE RD PORT TO THE DOWN PRESSURE DUMP VALVES ON THE WING SECTIONS OF THE PLANTER.

D.RESIDUE UP PRESSURE PORT-ROUTE BLUE AIR TUBING FROM THE RU PORT TO THE UP PRESSURE DUMP VALVES ON EACH SECTION OF THE PLANTER.

18

19

2940-101 Internal Lay Out

A.COMPRESSOR

B.FILTER

C.RELAY

D.STAINLESS STEEL BRAIDED COMPRESSOR LINE

E.CHECK VALVE

F.COMPRESSOR MANIFOLD

G.RELIEF VALVE

H.HIGH PRESSURE RELIEF LINE (2940-435)

I.COMPRESSOR PRESSURE SWITCH

J.LID

K.VALVE

L.WATER SEPARATOR VALVE

20

2940-101 Internal Lay Out

A.PQE

B.MANIFOLD

C.TRANSDUCER

D.REGULATOR

E.POWER INDICATOR

F.COMMUNICATION INDICATOR

G.SYSTEM FAULT INDICATOR

H.PRESSURE ON VALVE

I.VDM

J.J1 PORT-TRANSDUCER/VALVE CONTROL HARNESS

K.J2 PORT-DUMP VALVE CONTROL HARNESS

L.J3 PORT-PQE CONTROL HARNESS

M.J4 PORT-PQE 2 CONTROL PORT

N.J5 PORT-VDM POWER HARNESS

O.J6 PORTCOMMUNICATION CONTROL HARNESS

21

2940-103

2940-103 Compressor Control Module is an assembled unit, (less tank and compressor) that utilizes compressed air supplied by the OEM hydraulic compressor to operate the 2940 Air Adjust Residue Manager. OEM ELECTRIC COMPRESSORS ON PLANTERS

WILL NOT OPERATE YETTER 2940 AIR ADJUST SYSTEMS!

2940-103 MOUNTING GUIDE

22

2940-103 External Lay Out

A.WHEEL TRACK DOWN PRESSURE PORT- ROUTE BLACK AIR TUBING FROM THE WT PORT TO THE DOWN PRESSURE DUMP VALVE ON CENTER ROWS OF THE PLANTER. THE DOWN PRESSURE PSI ON THE CENTER SECTION RESIDUE MANAGERS CAN BE ADJUSTED SEPARATELY FROM THE WING SECTION RESIDUE MANAGERS DOWN PRESSURE PSI. IF THE WT PORT IS NOT USED, INSTALL THE 2940-352 PLUG TO PREVENT AIR LOSS.

B.RESIDUE DOWN PRESSURE PORT-ROUTE BLACK AIR TUBING FROM THE RD PORT TO THE DOWN PRESSURE DUMP VALVES ON THE WING SECTIONS OF THE PLANTER.

C.RESIDUE UP PRESSURE PORT-ROUTE BLUE AIR TUBING FROM THE RU PORT TO THE UP PRESSURE DUMP VALVES ON EACH SECTION OF THE PLANTER.

D.12 PIN DEUTSCH CONNECTOR (BLACK)-DEPENDING ON APPLICATION, CONNECT THE 2940-164, 2940-165 CAN AUX CABLE,OR 2940-170, 2940-171, OR 2940-430 CAN AUX TO AIR ASSEMBLY EXTENSIONS, AND ROUTE TO REAR OF TRACTOR. (MAKE SURE TABS OF

MALE END LINE UP WITH SLOTS IN FEMALE END)

E.12 PIN DEUTSCH CONNECTOR (GRAY)- CONNECT THE 2940-162 DUMP VALVE CABLE AND ROUTE TO THE DUMP VALVES VIA COLOR CODED (WHITE CABLES FOR UP PRESSURE DUMP VALVES AND BLACK FOR DOWN PRESSURE DUMP VALVES) DUMP VALVE EXTENSIONS AND “Y” HARNESSES. (MAKE SURE TABS OF MALE END LINE UP WITH SLOTS IN FEMALE END)

F.MAIN AIR SUPPLY INLET-PLUMB THE AIR LINE FROM HYDRAULIC COMPRESSOR ON PLANTER TO THE INLET AT THE WATER SEPARATOR, THE OUTLET AT THE REGULATOR WILL THEN CONNECT TO THIS PORT.

G.ACCESSORY AIR OUTPUT-BRASS CAP CAN BE REMOVED TO INSTALL FITTING FOR MISCELLANEOUS USES. (EX-AIR TOOLS) DO NOT REMOVE WHEN PRESSURIZED!

H.DUMP INLET-INSTALL THE ¼” AIR TUBING FROM BOTTOM OF WATER SEPARATOR TO THIS PORT.

I.DUMP EXHAUST- INSTALL THE ¼” AIR TUBING IN THIS PORT AND ROUTE TOWARD GROUND. (WILL DRAIN CONDENSATION FROM WATER SEPARATOR)

23

2940-103 Internal Lay Out

24

Connecting Air Supply from Hydraulic Compressor to 2940-103 Compressor Control Module

2940-415 Water Separator Lay Out

25

INSTALLING 2940 AIR ADJUST RESIDUE MANAGER KITS

READ BEFORE BEGINNING INSTALLATION

ENGAGE THE CYLINDER STOPS ON THE PLANTER LIFT WHEELS TO “LOCK” THE PLANTER IN THE UP POSITION

Installation overview:

Prior to installing check the freedom of motion of the row cleaner.

The installation process should be done with the planter raised, half folded for transport, and the row units fully extended down.

Install the 2940 Residue Manager Mounting Bracket Assembly centered on the planter row unit with provided hardware.

26

+ 60 hidden pages