Yeoman 280, 210, 200, 220, 270 User Manual
...
Elegance by Haas & Sohn
Freestanding
Multi-Fuel Stove
INSTALLATION, SERVICING
AND USER INSTRUCTIONS
Models 200 / 210 / 220 / 240 / 250 / 270 / 280
This product is for use only in Great Britain and Ireland (GB, IE)
These instructions are to be left with the customer
carefully and kept in a safe place.
They will be necessary when servicing the appliance.
IMPORTANT
Before installation of this product please read these instructions fully.
The installer should complete the commissioning sheet at the star
, should be read
t of the User Instr
PM173 Issue 2 (August 2006)
uctions.
Contents
elcome to Yeoman
W
ommissioning Data
C
echnical Specification
T
SITE REQUIREMENTS
tove Dimensions
S
earth Dimensions
H
Walls adjacent to Hearths 7
PRE-INSTALLATION CHECKS
Flue or Chimney 8
Additional Ventilation 9
3
4
5
6
7
INSTALLATION INSTRUCTIONS
Installing the Stove 10
Commissioning 11
OPERATING INSTRUCTIONS
General 12
Using the stove for the first time 12
Burning Wood 12
Burning Solid Fuel 13
Ash Removal 13
Recommended Fuels 14
MAINTENANCE AND SERVICING
General Cleaning 15
Cleaning Glass 15
Chimney Sweeping 15
Annual Service 15
2
Welcome to Yeoman
Your new Elegance multi-fuel stove is perhaps the most
advanced design of modern stoves. Owning such a stove
shows appreciation for e
Please read your manual thoroughly, its purpose is to
familiarise you with your stove, and give guidelines for its
installation, operation and maintenance. If after reading this
manual you need further information, please do not hesitate
to contact your Yeoman dealer.
xceptional quality.
IMPORTANT NOTICE
If your stove is installed correctly
of excellent service for which it was designed. This appliance
must be installed by a HETAS registered installer (GB only).
, it will give you many years
WARNING
All types of heating appliance can be potentially dangerous.
Correct installation and operating procedures must be
observed when fitting this stove. Some parts of your stove are
protected on their surface with heat proof paint. When the
stove is first used it is normal for it to emit some light smoke,
with an unpleasant smell. Though unpleasant, this is non
toxic and is produced only whilst the stove paint fully cures.
e recommend that you ventilate the room until this
W
disappears.
3
FOR YOUR RECORDS
o assist us in any Guarantee claim please complete the following information:-
T
YEOMAN DEALER APPLIANCE WAS PURCHASED FROM
Name: ..................................................................................................................................................................................................
Address:...............................................................................................................................................................................................
............................................................................................................................................................................................................
.
Telephone number:
....................................................................................................................................................
ESSENTIAL INFORMATION - MUST BE COMPLETED
Date installed:......................................................................................................................................................................................
Model Description:..............................................................................................................................................................................
Serial number:
..........................................................................................................................................................
INSTALLATION ENGINEER
Company name:...................................................................................................................................................................................
Address:...............................................................................................................................................................................................
.............................................................................................................................................................................................................
Telephone number:
....................................................................................................................................................................
COMMISSIONING CHECKS (TO BE COMPLETED AND SIGNED)
Is flue system correct for the appliance
Flue swept and soundness test complete YES NO
Smoke test completed on installed appliance YES NO
Spillage test completed YES NO
Use of appliance and operation of controls explained YES NO
Instruction books handed to customer YES NO
Signature: ........................................................................................................ Print name:
YES NO
4
......................................................
Model
Elegance 200 YM-EL200
Elegance 210 YM-EL210
Elegance 220 YM-EL220
Elegance 240 YM-EL240
Elegance 250 YM-EL250
Elegance 270 YM-EL270
Elegance 280 YM-EL280
TECHNICAL SPECIFICATION
Elegance 200
Elegance 210
Elegance 220
Elegance 240
Elegance 250
Elegance 270
Elegance 280
Nominal Heat Output kW
Flue Draught at Nominal Heat
Output
Flue Gas Mass Flow g/s
Flue Gas Temperature at
Spigot/Socket
Flue Outlet Size
Flue Position
Weight kg
Recommended Fuels
mm Wg
Inch Wg
°C
mm
inch
Wood
Solid Fuel
4.9 4.9 7 4.9 6 6 8
1.5 1.5 1.5 1.5 1.5 1.5 1.5
0.06 0.06 0.06 0.06 0.06 0.06 0.06
6.3 6.3 6.3 6.8 6.8 6.8 7.4
290 290 290 290 290 290 270
150 150 150 150 150 150 150
6 6 6 6 6 6 6
Top
Only
76 81 85 75 90 103 155
Top
Only
Seasoned wood (less than 20% moisture content).
Briquette smokeless fuel suitable for closed appliances.
(Ancit - Phurnacite - T
Top
Only
Top
Only
aybrite - Homefire Ovals).
Top
Only
Top
Only
Only
Top
5
SITE REQUIREMENTS
efore installation of this product please read these
B
nstructions fully.
i
It is very important to also understand the requirements
f the UK Building Regulations (England and Wales -
o
ocument J / Scotland - Part F), along with any local
D
egulations and working practices that may apply. Should
r
any conflict occur between these instructions and these
regulations then the regulations shall apply.
he Elegance Stove should be fitted by a HETAS (GB
T
nly) registered installer, or approved by your local
o
building control officer. Your Yeoman dealer should be
able to arrange this service for you.
our building insurance company may also require you to
Y
nform them that you have installed a new heating
i
appliance, so check with your insurers that your cover is
still valid after installing the Elegance Stove.
All electrical connections should meet the requirements
of UK Building Regulations (England and Wales Document P / Scotland - Part N).
Your local Building Control Office would be happy to
advise, should questions arise regarding the requirements
of the regulations.
ELEGANCE STOVE DIMENSIONS
Elegance 200
When completing the installation and building works you
should comply with your responsibilities under the Health
and Safety at Work Acts, and any new regulations, which
may be introduced during the lifetime of these
instructions.
A faulty installation could cause danger to the
inhabitants and structure of the building.
Elegance 220
Elegance 210
Elegance 240
6
SITE REQUIREMENTS
Elegance 250
Elegance 280
Elegance 270
7
SITE REQUIREMENTS
dditional information covering the installation of the
A
legance stove may be found in the British Standard:
E
BS8303.
HEARTH DIMENSIONS
The appliance must stand on a constructional hearth
with the minimum dimensions as shown in diagram
elow.
b
WALLS ADJACENT TO HEARTHS
50mm minimum
1
50mm minimum
1
Solid, non combustable
aterial e.g concrete or
m
asonry
m
150mm
minimum
C
A
Yeoman Elegance
C
150mm
minimum
Wall Thickness W
If you are fitting the appliance into an existing hearth
setting, check that it complies with the current
construction regulations and is at least the minimum sizes
shown.
If you have no existing fireplace or chimney, it is possible
to construct a suitable non-combustible housing and
hearth setting. However this should be constructed to
comply with the requirements of both current national
and local regulations with the design approved by your
local building control officer
. Masonry chimney systems
built with clay or concrete liners or pre-fabricated block
systems should be constructed in accordance with B
6461 : Part 1. F
actory made insulated systems should
comply with BS 4543 : Part 2 and be installed to BS 7566
: Parts 1 to 4.
Remember that any new chimney added to your property
may also require planning permission.
225mm
inimum
Constructional
hearth 840mm
inimum
m
m
Location of hearth
or Elegance Stove
Where the hearth
abuts a wall and the
Elegance Stove is
not more than
50mm from the
Change in level to
mark safe perimeter
Solid, non-combustible material
Thickness (W)
200mm
150mm
minimum
At least 300mm
above the
Elegance Stove
and 1200mm
above the hearth
Constructional
earth 840mm
h
minimum
Height (A)
wall
Where the hearth
abuts a wall and the
Elegance Stove is
more than 50mm
75mm
but not more than
300mm from the
S
wall
At least 300mm
above the
Elegance Stove
and 1200mm
above the hearth
Where the hearth
t least 300mm
does not abut a wall
and is no more
75mm
A
above the hearth
than 150mm from
the wall
Note: there is no requirement for protection of
the wall where C is more than 150mm
8
Loading...