Yeastar Elastix How to Connect Elastix to NeoGate TA FXS Gateway

Page 1
How to Connect Elastix to NeoGate TA FXS Gateway
How to Connect Elastix to NeoGate
TA FXS Gateway
Version: 1.0
Date: 2014.06.06
http://www.yeastar.com 1/15
Page 2
How to Connect Elastix to NeoGate TA FXS Gateway
Table of Contents:
1. Introduction..................................................................................... 3
2. Preparation ...................................................................................... 4
3. VoIP Mode ....................................................................................... 5
4. SPS/SPX Mode ................................................................................. 8
http://www.yeastar.com 2/15
Page 3
How to Connect Elastix to NeoGate TA FXS Gateway
1. Introduction
This application note shows how to connect Elastix to NeoGate TA FXS gateway. This guide has been tested with NeoGate TA3200 and Elastix firmware version:
2.4.0. Two modes are available for NeoGate TA to connect to Elastix, we call them VoIP trunk mode and Service Provider SIP/IAX trunk mode (SPS/SPX).
*You can simply choose one mode to achieve the connection.
Target
After connecting NeoGate TA3200 and Elastix, FXS extensions will be extended on Elastix. Once the FXS ports are connected to Elastix, the phones connected to the FXS ports will be treated as Elastix FXS extensions. The following features can be achieved:
1. Make calls between the analog phone and Elastix SIP extension;
2. Receive incoming calls on the analog phones;
3. Make external calls from the analog phones using trunks on Elastix.
Description
IP address of Elastix: 192.168.5.178 IP address of NeoGate TA3200: 192.168.5.13
Figure 1. Connect Elastix and NeoGate TA3200
http://www.yeastar.com 3/15
Page 4
How to Connect Elastix to NeoGate TA FXS Gateway
2. Preparation
NeoGate TA3200 attempts to contact a DHCP server in your network to obtain valid network settings (e.g., the IP address, subnet mask, default gateway address and DNS address) by default.
Before connecting NeoGate TA3200 to Elastix, you need to set a static IP address from the same LAN with the Elastix.
Steps to set static IP for NeoGate TA3200:
1. Connect one analog phone in one of the FXS ports on NeoGate TA3200;
2. Dial "***" to enter the voice menu;
3. Press "1" to check the IP address;
4. Open the browser and type in the TA3200's IP address to access TA3200;
5. Log in TA3200 and go to SystemNetwork PreferencesLAN Settings, disable DHCP and configure the LAN network, save and apply the changes, reboot NeoGate TA3200 to take effect.
Figure 2. Configure LAN Settings on NeoGate TA3200
http://www.yeastar.com 4/15
Page 5
How to Connect Elastix to NeoGate TA FXS Gateway
3. VoIP Mode
If you choose VoIP mode, the FXS ports will be registered as the Elastix's SIP extensions, whose functions are the same with other SIP extensions on Elastix.
Figure 3. Connect TA3200 and Elastix via VoIP Mode
Step 1. Create a SIP extension on Elastix.
Path: PBXExtensionsAdd Extension
Create an extension on Elastix for the FXS port on the TA3200 which has connected an analog phone. Here we take extension 9000 for example.
Figure 4. Create Extension 9000 on Elastix
Step 2. Configure one VoIP server template on NeoGate TA3200.
http://www.yeastar.com 5/15
Page 6
How to Connect Elastix to NeoGate TA FXS Gateway
Path: GatewayVoIP SettingsVoIP Server Settings
Check "Enable Register", fill in the Elastix IP address; this VoIP server template
will be a VoIP mode template.
Figure 5. Configure the VoIP Server Template as VoIP Mode
Server Name: Elastix Type: SIP Enable Register: checked Transport: UDP Hostname/IP: fill in the Elastix IP address, 192.168.5.178 Domain: fill in the Elastix IP address, 192.168.5.178
Step 3. Edit the Dial Pattern Template
Path: GatewayVoIP SettingsVoIP Server Settings
The default dial pattern is set as ".", which allows you to dial any number out. In this guide, we will remain the default setting. You can change it according to your environment.
http://www.yeastar.com 6/15
Page 7
How to Connect Elastix to NeoGate TA FXS Gateway
Figure 6. Edit Dial Pattern Template
Step 4. Edit the FXS port
Path: GatewayFXS Port ListFXS Port List
Figure 7. Edit the FXS Port
Primary Server: choose Elastix(3)”, the VoIP server template configured in
Step 2.
User Name: the extension username on Elastix, 9000. Authentication Name: the extension authentication name on Elastix, 9000. Password: the authentication password of the extension on Elastix,
pincode9000.
Dial Pattern Template: choose the Dial Pattern Template:
http://www.yeastar.com 7/15
Page 8
How to Connect Elastix to NeoGate TA FXS Gateway
DialPatternTemplate1(1).
Save and apply the changes, and you will see the port status is “Registered” on "Port Status" page. Path: StatusSystem StatusPort Status
Figure 8. Port Status
Now, you are able to use the analog phone which is connected to NeoGate TA's FXS port 1 to make calls and receive calls.
Note: ALL outgoing calls to Elastix extensions and to external numbers through
trunks on Elastix should match the dial pattern, or calls will fail.
4. SPS/SPX Mode
If you choose this mode to connect NeoGate TA3200 and Elastix, the FXS port will be registered as a Service Provider SIP/IAX (SPS/SPX) trunk to the Elastix. One SPS/SPX trunk to NeoGate TA also should be created on Elastix. In this guide, we use SIP protocol, configure one VoIP server template as SPS mode on NeoGate TA3200 and create one Service Provider SIP trunk on Elastix.
Figure 9. Connect TA3200 and Elastix via SPS Mode
http://www.yeastar.com 8/15
Page 9
How to Connect Elastix to NeoGate TA FXS Gateway
Step 1. Create a Service Provider SIP Trunk on Elastix
Path: PBXTrunksAdd SIP Trunk
Figure 10. Add SIP Trunk
http://www.yeastar.com 9/15
Page 10
How to Connect Elastix to NeoGate TA FXS Gateway
Figure 11. Configure SIP Trunk
PEER Details:
host=192.168.5.13 type=peer qualify=yes disallow=all allow=ulaw,alaw,gsm
After creating the SIP trunk, we can check the status of this trunk, it should be OK. Path: PBXTools Enter the command sip show peers and click Execute, the status will be seen.
http://www.yeastar.com 10/15
Page 11
How to Connect Elastix to NeoGate TA FXS Gateway
Figure 12. SIP Trunk Status
Step 2. Edit one VoIP Server template as SPS mode.
Path: GatewayVoIP SettingsVoIP Server Settings
Do not check "Enable Register", choose SIP protocol, and fill in the Elastix IP
address, the VoIP server template will be configured as SPS mode.
Figure 13. Configure the VoIP Server Template as SPS Mode
Server Name: Elastix Type: SIP Enable Register: DO NOT check Transport: UDP Hostname/IP: fill in Elastix IP address, 192.168.5.178 Domain: fill in Elastix IP address, 192.168.5.178
Step 3. Edit the Dial Pattern Template
http://www.yeastar.com 11/15
Page 12
How to Connect Elastix to NeoGate TA FXS Gateway
Path: GatewayVoIP SettingsVoIP Server Settings
The default dial pattern is set as ".", which allows you to dial any number out. In this guide, we will remain the default setting. You can change it according to your environment.
Figure 14. Edit the Dial Pattern Template
Step 4. Edit the FXS port
Path: GatewayFXS Port ListFXS Port List
Figure 15. Edit the FXS Port
Number: set a number for the FXS port. The number should be different from
the extension numbers on Elastix. Here we set number 100 for FXS port 2.
http://www.yeastar.com 12/15
Page 13
How to Connect Elastix to NeoGate TA FXS Gateway
Primary Server: choose Elastix(4), the VoIP server template configured on
step 2.
Dial Pattern Template: choose the Dial Pattern Template,
DialPatternTemplate1(1).
Note: You don't need to fill in any authentication name and authentication
password on the FXS port edit page if you choose SPS/SPX mode.
After saving and applying the changes, you will see the trunk is OK in “Line Status”. Path: StatusSystem StatusPort Status
Figure 16. FXS Port Status
Step 5. Create an inbound route on Elastix.
Path: PBXInbound RoutesAdd Incoming Route
Choose the inbound destination as IVR, when you call in Elastix from NeoGate TA3200, you will hear the IVR prompt. The inbound route configured here matches DID number 9999, users from NeoGate TA3200 should dial 9999 to reach Elastix.
http://www.yeastar.com 13/15
Page 14
How to Connect Elastix to NeoGate TA FXS Gateway
Figure 17. Add Incoming Route
Step 5. Create one outbound route on Elastix.
To make calls from Elastix to NeoGate TA3200, you need to create one
http://www.yeastar.com 14/15
Page 15
How to Connect Elastix to NeoGate TA FXS Gateway
outbound route on Elastix.
Path: PBXOutbound RoutesAdd Route
Figure 18. Add Outbound Route
Set the prefix as 9, choose the trunk "NeoGate" which is created above, then users should dial 9+number to call the phone which is connected to NeoGate TA3200. In this guide, you should dial 9100 to call the phone which is connected to TA3200 FXS port 2.
<End>
http://www.yeastar.com 15/15
Loading...