Yeacomm YF-P11 LTE Wireless Terminal User manual
Thanks for choosing Yeacomm 4G wireless router, please read and keep the user ’s manual carefully. It is more convenient for you to use our router.
We reserve the right to amend the technical parameters of the user ’s manual. We will improve the user ’s manual and adjust the printing errors in time without notification
in advance. All rights are reserved.
1. Main Technology Parameters
Working temps : -30℃ -- +60℃
Relative humidity : 5%--95%S
Working frequency could be customized.
Frequency : FDD: B1/B2/B3/B5/B7/B8/B12/B17/B20, B4/B28 (Optional)
TDD Band 38/39/40/41, B42/B43(optional)
WCDMA: 900/2100Mhz, 850/900/1900/2100Mhz(Optional)
GSM: 850/900/1800/1900Mhz
Frequency can be customized according to your requirements
Power supply : input AC :100V~240V，50Hz~60Hz
Output DC: 15V, 500mA
Rate of uplink and downlink :
LTE(Category 4): DL 150Mb/s；UL 50Mb/s
2. Installation
2.1.
Picture shows below. When you hear a “click” sound, it means that the USIM card has been installed successfully.
2.2. Use Cate5e cable to connect the POE’s CPE port and outdoor router L AN port.
2.3. placed the set outside at open space, the front direction toward the base station and fixed well .
2.4. Use POE Power supply connect External power outlet, the system will automatically pow er on after connected, about 1~2 minutes.
Attention ;
1) Please do not insert USIM card when connecting with the external power supply
2) Please do not contact with the mental surface when removing the USIM card, it will da mage the card.
3) Please use the original standard power adapter.
3. About Terminal
The terminal can work under the LTE network, only suppor ts data and SMS service and doesn’t support voice business.
3.1. Equipment connection diagram。
3.1.1. interface introduction
Port type
Port function
remarks
SIM
Install USIM card interface, please
follow the instructions install USIM
card, stick the waterproof stickers
after installed card
Please do not insert or take out the SIM card when the power
on.
LAN
Ethernet port， U se to connect
router WAN/POE port
PC and outdoor router should use Cate5 connect, and the
distance should within 50 meters.
3.2. Indicator
Type
Status
Description
RF
All off
no signal (the signal status can be checked
by terminal configuration page)
One on
The signal is poor
Two on
Signal is moderate
Three on
Signal is good
All on
Signal is very good
SYS
Off
Power abnormal, the router power off
On
Power normal, the router power on
SIM
Off
No SIM orCan not read SIM
On
Terminalread the SIM normally
ETH
Off
Terminaldoesn't link with PC
On
Terminalhave link with PC
RUN
Off
Terminalis doesn't running
On
Terminalis running
4. Access internet
The router support standard internet cable to connect computer, do not need any driver; Support Windows XP, Windows 7,Windows 8,MAC OS, Linux, Android and so on;
Please confirm the set has been installed well ad the manual before access the internet.
4.1. Access PC
The router support standard internet cable to connect computer, No matter what way to connect, please make sure to set the mode: obtain IP address as automatically.
4.2. Access terminal
Please enter”192.168.0.1” in the IE browser after the computer obtain the IP address .Then input the “user name ” and “password" to access the router
configuration page. Default “user name” and “password“both are admin.
Log into the device configuration page below browsers are recommende d:
● at least IE 7.0 ● at least Firefox 3.0
● at least Safari 4.0 ● at least Opera 10.0
● at least Chrome 10.0
5. Router setting
Please make sure that the router is in normal running and is connected with the computer when configure router. A part of the configure parameters have to set under
operators advise, if take the error parameters, the internet would be out of service. Long press “reset” button restore to factor y settings.
Menu 1
Menu 2
description
System
status
Home gateway
information status
Youcan check the router running status info, such as running hours, LTE
network info, SIM info, WAN, LAN info , WLAN info and so on .
Online terminal
status
Check the user’s info who has connected with the terminal, including MAC
address, IP address and so on
TrafficStatistics
Check all the traffic status since the first running time, specific traffic
information is according to the operator’s d ata.
Version info
Check the router's software and hardware version number.
LTE info
Check LTE details info, including frequency, cell, RSRP, SINR, RSRQ etc.
Device
Setting
WAN Setting
Network selection: wireless network and PLMN mode optional
User can select 4G/3G/2G networks. 4G is the fastest, 3G medium, 2G slowest. If
in multiple selection can set the priority network, the router could register to
the priority network once it is the fastest. Default setting is in multiple
selections, 4G preferred.
PLMN is the default setting. User can activated manual option if necessar y.
Manual option needs searching the available PLMN in advance.
IPV4 / IPV6: Set router IP stack support model. The default setting is IPV 4 /
IPV6 dual stack.
APN: Set the access name when you dial. The setting needs follow operator’s
requirement, any change may lead to being unable to access to the internet .
Not recommend changing it.
PIN code: Set USIM card PIN1 and PUK. If the USIM card enable PINI code or
PUK code, then you need to fill in the appropriate PINI code .Otherwise, the
router will not dial .
MTU: Set the MTU parameters of the router network port. Do not recommend
to change, otherwise it will cause abnormal network. It needs professional
selection
DNS setting :set the DNS server address .
WLAN Setting
WLAN setting: Turnon/off function of WIFI, view / change WIFI SSID, password,
encryption, channel etc. User can modify router WIFI SSID, password and
encryption methods. It takes the current channel in use. Channel could be
modified.
DHCP
DHCP: Set the router’s DHCP info and IP info, once turn off the DHCP, the user
has to set IP manually, and it can not obtain the IP automatically.
Keep address: Reserved address is only effective when you enable DHCP ser ver,
click [Add] button to formulate MAC address binding fixed IP address, this I P
address will only be assigned to the MAC address which the computer belongs.
IPV6 set
Setting IPV6 address allocation, PNAT function.
SMS
function
New message
Youcan edit new message and send it
In box
Check received message
Draft
Check edited but not send message
Sent
Check the message sent message
Firewall
Filtering Rules
Ports filtering: Set the ports which need to be filtered
IP address filtering: Set the IP address which need to be filtered.
MAC address filtering：Set the MAC address which needs to be filtered.
URL Filtering: Set the website which needs to be filtered.
MAC binding: Set binding IP and MAC address.
Default rules: Set other filtering r ules which has not included here.
Speed limit
Setting speed limit rule, only IP address limit currently
System
manage
ment
System setting
Change Password: Change password logging into the router configuration
page.
Change user name: change the log on user name.
Reboot setting: reboot setting.
System Time: Set the router system time.
System log
Check system work log
Reboot
Support reset router
System update
When the system update, you must download the updated file to your
computer .The device supports tar.gz or tar.lzma format update file, you need to
unzip the file .After the computer has obtained the upgrade files, update files
need to upload to the device first, meanwhile also need to upload MD5
verification code during the upgrade. After uploading, you can click to upgrade
system. The system upgrade will not remove your previous profile
Module update
Update the LTE module software
Configurable
update
Update router system setting
Restart device
User can restart router
Online help
View self-help files for router
Loading...