YCL MF601BE Datasheet
Product Specification
MF601BE
Data sheet subject to change without notice RDPS-MF055(R0)09/30/2002
SHEET 1 OF 11
File No RDPS-MF055
Revision R0
System Application Mirco Filter For ADSL CPE Side
Product Type Micro filter
Product Name MF601BE
Date Sep. 30th, 2002
Bert Lin - Design Engineer, R&D_1
Issued By
bert@ycl.com.tw
Roger Wu - Manager, R&D_1
Approved By
roger@ycl.com.tw
Issued Date
YCL Electronics Co., Ltd.
No.95, Feng Jen Road, Feng Shan City, Kaohsiung County, Taiwan, R.O.C.
This controlled document is the property of YCL Electronics Co., Ltd. Any duplication
reproduction or transmission by unauthorized parties without the prior written
permission of YCL Electronics Co., Ltd. is prohibited.
Product Specification
MF601BE
Data sheet subject to change without notice RDPS-MF055(R0)09/30/2002
SHEET 2 OF 11
Table of contents
Item Description Page
1. Introduction ----------------------------------------------- 3
2. Compatibility ----------------------------------------------- 3
3. References ----------------------------------------------- 4
4. Abbreviations ----------------------------------------------- 4
5.
Technical requirements
----------------------------------------------- 5
5.1. Schematic ----------------------------------------------- 5
5.2. ZHP-r definition ----------------------------------------------- 5
5.3. Electrical specification ----------------------------------------------- 6
5.4. DC characteristics ----------------------------------------------- 8
5.5. Test methods ----------------------------------------------- 8
5.5.1 . Off-hook insertion loss ----------------------------------------------- 8
5.5.2 . Return loss
----------------------------------------------- 9
5.5.2.1. Complex* return loss with ATU-R ----------------------------------------------- 9
5.5.2.2. 600 ohm return loss with ATU-R ----------------------------------------------- 9
6 Environmental condition
----------------------------------------------- 10
6.1. Resistibility to overvoltage and
overcurrents
----------------------------------------------- 10
6.2. Climatic condition
----------------------------------------------- 10
6.2.1. Operating temperature
----------------------------------------------- 10
6.2.2. Storage and transport
----------------------------------------------- 10
4.2.3. Operating humidity
----------------------------------------------- 10
7 Reliabilty conditions
----------------------------------------------- 10
7.1.Thermal shock
----------------------------------------------- 10
7.2. Temperature humidity exposure
----------------------------------------------- 10
7.3. Vibration test
----------------------------------------------- 10
8. Mechanical conditions ----------------------------------------------- 11
8.1. Mechanical ----------------------------------------------- 11
8.2. Connector information ----------------------------------------------- 11
Product Specification
MF601BE
Data sheet subject to change without notice RDPS-MF055(R0)09/30/2002
SHEET 3 OF 11
1. Introduction:
The in-Line Micro filter has been specifically designed to implement the functionality of low
pass filter in G.Lite system.G.Lite technology is similar to full rate ADSL in using DMT
technology but operates at a lower data rate of up to 1.5Mbps downstream and 512Kbps
upstream ,depending on line conditions and lengths.ADSL Lite is proposed as a lower speed
version of ADSL that will eliminate the need for telecom to install and maintain a premises
based POTS splitter. It was found necessary to include one or more low pass filters in series
with the POTS terminals in order to reliably achieve maximum data rates.
For POTS voice band service , the low pass filter provide protection from ADSL signal which
may impact through non-line or other effects remote devices(handset, fax, voice band modem
etc)and central office operation . For ADSL signal , it also provide protection from the high
frequency transient and impedance effect that occur during POTS operation(ringing
transients , on-hook,off-hook transient and so on).
Because the POTS splitter connects directly to the subscriber loop media , it must also
provide some protection for externally induced line hits or faults which could damage any
attached equipment or endanger humans interacting with the installed equipment.The circuit
protection will be provided mostly by standard central office line protection means and
additional protection measures built into pots splitter to protect against line overstress which
could damage the splitter itself.
2. Reference:
Ref. 1 : ETS 300 001 Attachment to Public Switched Telephone Network
Ref. 2 : ANSI T1E1.4 G.992.2 Network and Customer Installation Interface
Ref. 3 : ITU-T K20 Resistibility of telecommunication switching
Equipment to overvoltages and overcurrents
Ref. 4 : ITU-T K21 Resistibility of subscribers terminal to overvoltage and
overcurrents
Product Specification
MF601BE
Data sheet subject to change without notice RDPS-MF055(R0)09/30/2002
SHEET 4 OF 11
3. Abbreviations:
ADSL Asymmetric Digital Subscriber Line
CO Central Office
CPE Customer Premise Equipment.
POTS Plain Old Telephone Service
RT Remote Terminal
ADSL-NT Network termination of ADSL
4. Abbreviations:
ADSL Asymmetric Digital Subscriber Line
CO Central Office
CPE Customer Premise Equipment.
POTS Plain Old Telephone Service
RT Remote Terminal
DSL-NT Network Termination of ADSL
Loading...