OWNER’S MANUAL
WWW.YBIKE.CO.ZA
IMPORTANT SAFETY NOTICE
WARNING
SAFETY PRECAUTIONS:
DO NOT use this product on slippery, wet, or uneven ground with gravel.
DO NOT ride this product with one or no hands. The handlebars should be held tightly with two hands.
1
Children riding this product should have constant adult supervision. A responsible adult must inspect
the product thoroughly prior to use to ensure that all parts are correctly assembled and tightened to
prevent accidents.
Always ensure proper protective gear is worn such as a helmet, elbow and kneepads as well as the
appropriate clothing e.g. a long sleeve shirt, gloves, long pants, and trainers or closed footwear. Do
not allow your child to ride this product barefoot or in sandals.
DO NOT allow the product the be used during dusk or in the dark. Only allow usage in good lighting
to avoid accidents.
Riding this product can be a hazardous activity and precautions should be taken to avoid dangerous
situations. Be sure to read the entire manual before riding. Please pay close attention to the following
precautionary measures:
WARNING! This bike is intended to be assembled by an adult.
WARNING
ALWAYS follow and obey the local traffic laws.
Injury may occur if these precautions are not observed.
2
The product should only be used on flat and level ground. DO NOT ride the balance bike on slopes.
DO NOT go down a long descending slope or hill. Please be careful when passing these areas.
Ensure that the product’s handlebar is securely fixed and that it moves smoothly by turning it left and
right before allowing your child to use the product.
DO NOT use attachments not included in packaging or attempt to do any modifications yourself as
this may compromise the safety of the product.
Make sure all components are assembled correctly and securely before allowing your child to use
the product.
Never allow more than one child to ride on the product at any time.
NOTE: Any photos or decals of the YBIKE TOYNI used in the owner’s manual are intended for reference
purposes only. There may be some differences to the unit you purchased.
TOYNI PARTS LIST & COMPONENTS
3
No. NAME
1 MAIN BODY
3
2
4
5
6
7
8
9
10
11
2 X BACK WHEELS
WHEEL FORK
FRONT WHEEL
2 X SHAFT CAPS
FORK BOLT - M6 x 175mm
FRONT WHEEL BOLT - M6 x 130mm
HANDLEBAR
2 X BOLT CAPS
2 X ALLEN KEYS
SHAFT
3
1
2
6
7
8
9
4
10
11
5
Open the box and take out all of its contents. Make sure all of the
parts and components listed below are included:
ENLARGED FOR EASE OF
REFERENCE
ASSEMBLY INSTRUCTIONS
1. Front Wheel Fork Assembly
4
Position the Wheel Fork (No. 2)
and Handlebar (No. 9) into the
hole in The Main Body (No. 1)
as shown. Ensure that the
Wheel Fork is correctly positioned inside the Handlebar.
Push the Fork Bolt (No. 6) down
the hole from the top of the
Handlebar (No. 9) and
through the Wheel Fork (No.2).
1
2
6
9
10
10
8
2
9
NOTE: The Front Wheel Fork
(No. 2) must be positioned
with the steering guide
facing forward as shown
above.
Screw the Bolt Cap (No.8) into
the bottom end of the Fork Bolt
(No.6) and tighten using the
Allen Keys (No.10).
(Do not over tighten bolts as this may cause damage.)
ASSEMBLY INSTRUCTIONS
5
Position the Front Wheel (No.4)
between the arms of the Wheel
Fork (No.2) with their holes
aligned.
Push the Front Wheel Bolt (No.7)
through the holes in the Fork
and Wheel.
Screw the Bolt Cap (No.8) into
the threaded end of the Front
Wheel Bolt (No.7) and tighten
using the Allen Keys (No.10).
2. Front Wheel Assembly
(Do not over tighten bolts as this may cause damage.)
2
10
7
8
10
4
ASSEMBLY INSTRUCTIONS
6
Back Wheel Assembly
Push the Shaft (No.11) through
the hole at the back of the Main
Body (No.1).
Screw the Shaft Caps (No.5) onto
either ends of the Shaft (No.11).
Ensure that they are tightly
fastened.
NOTE: The Shaft (No.11) has rectangular
details. Ensure that it is correctly
positioned when pushing it through the
Main Body (No.1) & Back Wheels (No.3).
NOTE: Wheels can be attached in the beginner’s or the
advanced balancing position. Refer to page 7 for
position details.*
*Wheels shown above in Advanced Balancing Position
3
1
5
5
3
11
Position Back Wheels (No.3) onto
the Shaft on either side of the
Main Body (No.1). Make sure that
the Shaft protrudes slightly from
the Wheels as shown.
BALANCING SETTINGS
7
HOW TO CHANGE THE BALANCING SETTING ON YOUR TOYNI:
Unscrew and remove the Shaft Caps (No.5)*. Remove the Back
Wheels, flip, reposition onto Shaft and reattach Shaft Caps (No.5)
*Refer to page 6 for Assembly Diagram.
BEGINNER BALANCING SETTING ADVANCED BALANCING SETTING
50mm
155mm
CHECK BEFORE RIDING
1. Check that all the bolts are securely tightened.
3. Check that the wheels can spin smoothly and that each part
is securely fixed.
4. Finally, after checking the above points, you can now start
riding your new balance bike.
WARNING! This product must be assembled by an adult. Read the
manufacturer’s instructions before using. Keep the instructions safe
for future reference.
ENJOY YOUR YBIKE TOYNI
8
2. Check that the handlebar is securely fastened and that it
moves smoothly.
WWW.YBIKE.CO.ZA
Loading...