YardLine Crestwood Gable User Manual
STOP!
STOP!
16574
Call Us First!
DO NOT RETURN TO STORE.
For immediate help with assembly or product information
call our toll free number:
1-800-844-9273
or email:
customerservice@yardline.net
Our staff is ready to provide assistance
M-F 8:00 AM to 6:00 PM EST
Saturday 8:30 AM to 5:00 PM EST
(This page intentionally left blank.)
A Backyard Products Company
CRESTWOOD GABLE 8' x 14' (244 x 426,7 cm)
ACTUAL FLOOR SIZE IS 96 x 168" (243,8 x 426,7 cm)
KEEP THIS MANUAL FOR FUTURE REFERENCE
16574
05/09/2016
OPTION 1:
DOOR LOCATION
LEFT SIDE OF FRONT WALL
OPTION 2:
DOOR LOCATION
RIGHT SIDE OF FRONT WALL
IMP ORTANT!
READ INSTRUCTIONS THOROUGHLY PRIOR TO BEGINNING ASSEMBLY.
BEFORE YOU BEGIN
• BUILDING RESTRICTIONS AND APPROVALS
Be sure to check with local building department and homeowners association for speci c restrictions and/ or requirements before building.
• ENGINEERED DRAWINGS
Contact our Customer Service Team if engineered drawings are needed to pull local permits.
• SURFACE PREPARATION
To ensure proper assembly you must build your shed on a level surface. Recommended methods and materials to level your shed are
listed on page 9.
• CHECK ALL PARTS
Inventory all parts listed on pages 3 - 7. Contact our Customer Service Team if any parts are missing or damaged.
• ADDITIONAL MATERIALS
You will need additional materials to complete your shed. See page 8 for required and optional materials and quantities.
- CUSTOMER SERVICE -
Call: 1-800-844-9273 email: customerservice@yardline.net
TOOLS
OptionalRequired
❑ Phillips
Screwdriver
❑ Drill / Driver
❑ 1/8" Drill Bit
❑ 1/4" Drill Bit
❑ 5/16" Drill Bit
❑ 1/2" Drill Bit
❑ #2 Philips Drive Bit
❑ Hammer
❑ Level
❑ Pencil
❑ Tape Measure
❑ Square
or
Safety! Always use approved safety glasses during assembly.
HELPFUL REMINDER SYMBOLS
Look for these symbols for helpful reminders throughout this manual.
= Assistance Required; two or more people.
❑ Utility Knife
❑ Shingle Blades
❑ Caulk Gun
❑ Paint Tools
❑ Safety Glasses
❑ Hand Saw
❑ Ladder
❑ Tool Belt/
Nail Pouch
❑ Tin Snips
(for drip edge)
❑ Chalk Line
❑ Nail Gun
• gun nails
❑ Gloves
= Mark part with pencil.
= Ensure squareness.
= Important required step or operation.
= Helpful assembly hint.
BEGIN
FINISH
= Beginning of steps for assembly or installation.
= You have nished the assembly or installation.
= Level
ORIENT LUMBER AND TRIM FOR BEST APPEARANCE
Framing lumber is graded for structural strength and not appearance. Exterior trim is graded for one good side.
Always install the material leaving the best edge and best surface visible. Please remember that these blemishes in no way
negatively affect the strength or integrity of our product. (See Fig. A, B, C.)
A
B C
2
PARTS IDENTIFICATION AND SIZES
3/4"
letters are stamped on some parts.
Part identication
RS
RS
Check these locations for
part stamp.
WOOD SIZE CONVERSION CHART
Nominal Board Size Actual Size
2" x 4"..............1-1/2" x 3-1/2" (3,8 x 8,9 cm)
1" x 4".................3/4" x 3-1/2" (1,9 x 8,9 cm)
2" x 3"..............1-1/2" x 2-1/2" (3,8 x 6,3 cm)
1" x 3".................3/4" x 2-1/2" (3,8 x 6,3 cm)
PARTS LIST
INVENTORY YOUR PARTS before you begin.
We suggest sorting parts by the category they are listed in.
1 x 3 x 5" (2,5 x 7,6 x 12,7 cm) Gauge Block for 3/4" (1,9 cm) measurement
GAA
x1
x2
2 x 4 x 6" (5,1 x 10,2 x 15,2 cm)
PVA
(1,9 cm)
WALLS
RAFTERS
x4
x5
x2
x2
x6
x2
x1
x2
x3
x24
x3
x4
x14
x2
x16
x2
CPA
PWA
AJ
ABA
AO
QT
UX
YFA
TM
TK
SZ
TP
JF
ASA
2 x 4 x 8-1/2" (5,1 x 10,2 x 21,6 cm)
2 x 4 x 10" (5,1 x 10,2 x 25,4 cm)
2 x 4 x 12-1/2" (5,1 x 10,2 x 31,8 cm)
2 x 4 x 20" (5,1 x 10,2 x 50,8 cm)
2 x 4 x 22-1/2" (5,1 x 10,2 x 57,1 cm)
2 x 4 x 35" (5,1 x 10,2 x 88,9 cm)
2 x 4 x 64" (5,1 x 10,2 x 162,6 cm)
2 x 4 x 68-1/2" (5,1 x 10,2 x 174 cm)
2 x 4 x 72" (5,1 x 10,2 x 182,9 cm)
2 x 4 x 80" (5,1 x 10,2 x 203,2 cm)
2 x 4 x 89" (5,1 x 10,2 x 226,1 cm)
2 x 4 x 96" (5,1 x 10,2 x 243,8 cm)
6 x 24" (15,2 x 61 cm) OSB OR WOOD GRAIN
1 x 4 x 60" (1,6 x 10,2 x 152,4 cm)
2 x 4 x 63-7/8" (5,1 x 10,2 x 162,2 cm)
3/8 x 10 x 17" (1 x 25,4 x 43,2 cm)
TRIM
x4
x2
x2
x4
x2
x2
x8
x2
x2
ATA
3/8 x 4-3/4 x 54-5/8" (1 x 12,1 x 138,7 cm)
3/8 x 4-3/4 x 64-1/8" (1 x 12,1 x 162,9 cm)
3/8 x 4-3/4 x 64-1/8" (1 x 12,1 x 162,9 cm)
2 x 4 x 64-1/8" (5,1 x 10,2 x 162,9 cm)
3/8 x 4-7/8 x 73-1/2" (1 x 12,4 x 186,7 cm)
3/8 x 4-3/4 x 77-1/4" (1 x 12,1 x 196,2 cm)
3/8 x 1-3/4 x 81-1/2" (1 x 4,4 x 207 cm)
3/8 x 4-7/8 x 96" (1 x 12,4 x 243,8 cm)
3/8 x 4-3/4 x 96" (1 x 12,1 x 243,8 cm)
3
x3
WINDOW TRIM, DOOR TRIM & SHUTTERS
JTA
19/32 x 6-7/16 x 2" (1,5 x 16,4 x 5,1 cm)
NRA
x3
x4
x1
x4
DJA
AZ
DHA
x1 DDA
x1
AUA
DEAx1
OOx3
x2
x1
LRA
DGR
19/32 x 6-7/16 x 5-1/2" (1,5 x 16,4 x 14 cm)
19/32 x 2-1/2 x 11" (1,5 x 6,3 x 27,9 cm)
19/32 x 2-1/2 x 30-1/8" (1,5 x 6,3 x 76,5 cm)
19/32 x 5-1/2 x 30-1/8" (1,5 x 14 x 76,5 cm)
19/32 x 3-1/2 x 40" (1,5 x 8,9 x 101,6 cm)
19/32 x 2-1/2 x 53" (1,5 x 6,3 x 134,6 cm)
19/32 x 3-1/2 x 55" (1,5 x 8,9 x 139,7 cm)
1-1/4 x 2-1/2 x 69" (3,2 x 6,3 x 175,3 cm)
1 x 4 x 69-3/4" (2,5 x 10,2 x 177,2 cm)
19/32 x 2-1/2 x 70-7/8" (1,5 x 6,3 x 180 cm)
x2
DGL
x1 DFA
x1
ZJ
NOTE: Panel parts are not stamped.
x2
x2
x1
AED
2 x 3 x 21-3/4" (5,1 x 7,6 x 55,2 cm)
19/32 x 2-1/2 x 70-7/8" (1,5 x 6,3 x 180 cm)
19/32 x 3-1/2 x 72" (1,5 x 8,9 x 182,9 cm)
19/32 x 2-1/2 x 72" (3,2 x 6,3 x 182,9 cm)
LOFT & SHELVES
7/16 x 10-1/2 x 89" (1,1 x 26,7 x 226,1 cm)
7/16 x 26-5/8 x 89" (1,1 x 67,6 x 226,1 cm)
x5
x1
PT
TP
2 x 3 x 96" (5,1 x 7,6 x 243,8 cm)
2 x 4 x 96" (5,1 x 10,2 x 243,8 cm)
4
WALL PANELS & DOORS
NOTE: Panel parts are not stamped.
x5
3/8 x 48 x 84"
(1 x 121,9 x 213,4 cm)
x1
3/8 x 48 x 84"
(1 x 121,9 x 213,4 cm)
x1
3/8 x 23-7/8 x 84"
(1 x 60,6 x 213,4 cm)
x1
3/8 x 48 x 84"
(1 x 121,9 x 213,4 cm)
x2
3/8 x 11-7/8 x 84"
(1 x 30,2 x 213,4 cm)
x1
3/8 x 48 x 84"
(1 x 121,9 x 213,4 cm)
x1
3/8 x 48 x 84"
(1 x 121,9 x 213,4 cm)
x1
3/8 x 48 x 84"
(1 x 121,9 x 213,4 cm)
x2
x2
UNIVERSAL DOOR
Right / Left
x1
Painted
on Ends
5
Black
Painted
Green on End
Red on End
x1
LEFT DOORx1RIGHT DOOR
Painted
x2
2 x 4 x 72" (5,1 x 10,2 x 182,9 cm)
x12
2 x 4 x 93" (5,1 x 10,2 x 236,2 cm)
x2
2 x 4 x 96" (5,1 x 10,2 x 243,8 cm)
FLOOR PARTS
NOTE: Panel parts are not stamped.Floor panels are 5/8" (1,6 cm) thick.
Look for
TREATED
Stamp
x1
5/8 x 23-7/8 x 96"
(1,5 x 60,6 x 243,8 cm)
x2
7/16 x 15-7/8 x 23-7/8"
(1,1 x 40,3 x 60,6 cm)
x2
7/16 x 15-7/8 x 48"
(1,1 x 40,3 x 121,9 cm)
x2
7/16 x 15-7/8 x 96"
(1,1 x 40,3 x 243,8 cm)
x3
5/8 x 48 x 96"
(1,5 x 121,9 x 243,8 cm)
ROOF PANELS
NOTE: Panel parts are not stamped.Roof panels are 7/16" (1,1 cm) thick.
x2
7/16 x 48 x 71-7/8"
(1,1 x 121,9 x 182,6 cm)
x2
7/16 x 48 x 96"
(1,1 x 121,9 x 243,8 cm)
6
x130
x335
x113
x30
x27
x100
x25
x7
x4
FASTENERS & HARDWARE
FASTENER/HARDWARE BAG
1-1/2" (3 ,8 cm)
2" (5,1 cm)
3" (7,6 cm)
2" (5,0 cm)
1-5/8" (4,1 cm)
3/4" (1,9 cm)
1" (2,5 cm)
Boxes
2" (5,1 cm)
Boxes
3" (7,6 cm)
x2
VENT/ DOOR HARDWARE/ WINDOWS
Window
22-1/4 x 29-3/4"
(56,5 x 75,6 cm)
Vent with Frame
T-Handle
x2
x1
4-1/2" Shaft
x1
5-1/2" Shaft
x4
1-1/2" (3,8 cm)
(2 screws in each package)
Decorative Hinges
x6
Spring Bolt
x2
x8
1" (2,5 cm)
(4 screws in each package)
x2
x18
1" (2,5 cm)
7
ADDITIONAL MATERIALS
FOUNDATION OR FLOOR MATERIALS
• This shed does not include any leveling materials.
• See the FLOOR LEVELING section on page 9 for recommended methods and suggested materials to properly level your oor,
as this will vary depending on your specic site.
• If you choose to install your kit on a concrete slab refer to page 10.
REINFORCED WOOD FLOOR FRAME (OPTIONAL)
IMPORTANT! Depending on your specic use you may want to construct a heavy duty oor frame by adding additional oor joists
(shown below as shaded). Below is a list of additional materials (not included):
2 x 4 x 8' (5 x 10 x 243,8 cm) Treated Lumber
x3
Cut to (3) 2 x 4 x 93" (5 x 10 x 236,2 cm)
ea. 3" (7,6 cm) Hot Dipped Galvanized Nails
x12
Optional 12" (30,5 cm) spacing
Standard 16" (40,7 cm) spacing
COMPLETING YOUR SHED
You will need these additional materials:
3-TAB SHINGLES ............................. 7 Bundles
PAINT FOR SIDING .......................... 3 Gallons
Use 100% acrylic latex exterior paint. (2) coats recommended.
CAULK ................................................. 2 Tubes
Use acrylic latex exterior caulk that is paintable.
1" GALVANIZED ROOFING NAILS.... 3 Lbs
For shingles.
PAINT FOR TRIM .......................... 3 Quarts
Use 100% acrylic latex exterior paint.
WOOD GLUE ....................... Exterior Rated
OPTIONAL MATERIALS
DRIP EDGE ..................... 60 Feet #15 ROOFING FELT
To cover 160 Sq. Ft. of roof area.
1" GALVANIZED ROOFING NAILS.........1/4 Lb
For roong felt.
REFER TO THE BACK OF THIS MANUAL AND THE MANUFACTURER’S INSTRUCTIONS FOR
INSTALLATION OF SHINGLES, DRIP EDGE AND FELT.
8
OPTIONAL WOOD FRAME FLOOR LEVELING OPTIONS
There are multiple ways to level your oor frame. Our recommended leveling method is shown below.
Leveling materials are not included in this kit.
PREFERRED METHOD - 4x4 TREATED RUNNERS (Typical for 8' x 14' Kit)
Runners are generally 12" (30,5 cm) from
ends of oor frame and under seams.
Measurements to
centers of 4x4's.
• 3" Screws angled into 4x4.
• (2) at each point frame
and 4x4 touch.
MATERIAL REQUIRED
16"
(40,6 cm)
12"
(30,5 cm)
Fasteners for Frame to 4"x 4".
(3" Screws shown as one option.)
Minimum 3" screws / exterior grade.
DOOR
12"
(30,5 cm)
4" x 4" x 14' (10,2 x 10,2 x 426,7 cm) Treated Lumber
x2
x48
Use only wood treated for ground contact and fasteners approved for use with treated wood.
Always support frame seams.
Gravel
LEVELING METHODS
12"
2" Block
Maximum between leveling
material locations.
48"
Gravel
2x4 Treated Lumber
Shingle
Level
4" Block
4x4 Runner
12"
8" Block
Shingle
Do not exceed 16".
• Level under 4x4 runners only.
• Locate leveling material 12" from ends of runners and no more than 48" apart.
• Asphalt shingles should be used between 4x4 runners and blocks or treated lumber. Never use
shingles in direct contact with ground.
• For best results and aiding in water drainage use gravel under each concrete block.
3" (7,6 cm)
LEVELING MATERIALS
Gravel
Solid Masonry Blocks in 1", 2", 4" or 8" thickness
2x4 Treated Lumber
Asphalt Shingles
Leveling higher than 16" not recommended.
CONCRETE
• If you are building your shed on a concrete foundation see the following page.
9
CONCRETE FOUNDATION
DOUBLE
DOOR
SINGL E
DOOR
Your kit contains all materials to construct a wooden oor. If you choose to install your kit
on a concrete slab refer to the diagram below.
Treated Sill Plate
Caulk between sill
plate and concrete.
C
B
3-1/2"
(8,9 cm)
A
4"
(10,2 cm)
AActual Size B CBuilding Size
8' x 14' (243,8 x 365,8 cm)
Requires:
Allow new concrete slabs to cure for at least seven (7) days.
• A treated 2 x 4" (5,1 x 10,2 cm) sill plate is required when installing your shed on concrete.
Hint: Purchase full length treated lumber.
• Use a high quality exterior grade caulk beneath all sill plates.
• Fasten 2 x 4" (5,1 x 10,2 cm) sill plates to slab using approved concrete anchors (fasteners not included).
• Check local code for concrete foundation requirements.
96" x 168" (243,8 x 426,7 cm)
2" x 4" x 14' (5,1 x 10,2 x 365,8 cm)
x2
x2
2" x 4" x 8' (5,1 x 10,2 x 244 cm)
Caulk
x1
96" (243,8 cm)
MUST be treated lumber.
MUST be treated lumber.
161" (408,9 cm)
168" (426,7 cm)
NOTES
10
FLOOR FRAME
PARTS REQUIRED:
x12
2 x 4 x 93" (5,1 x 10,2 x 236,2 cm)
x2
2 x 4 x 96" (5,1 x 10,2 x 243,8 cm)
x2
BEGIN
Orient parts as shown on at surface. Measure and mark.
1
Use two 3" nails at each mark.
FINISH
You have nished your oor frame. Proceed to level and square frame.
72"
(182,9 cm)
2 x 4 x 72" (5,1 x 10,2 x 182,9 cm)
168"
(426,7 cm)
160"
(406,4 cm)
x44
144"
(365,8 cm)
HINT:
For easier nailing
stand on frame.
128"
(325,1 cm)
112"
(284,5 cm)
Look for
TREATED
Stamp
(243,8 cm)
(243,8 cm)
96"
96"
3" (7,6 cm)
80"
(203,2 cm)
64"
(162,6 cm)
48"
(121,9 cm)
32"
(81,3 cm)
(40,6 cm)
16"
96"
(243,8 cm)
Flush
Flush
93"
(236,2 cm)
(182,9 cm)
72"
TOENAILING
Center
on marks
96"
(243,8 cm)
Flush
Flush
11
LEVEL AND SQUARE FLOOR FRAME
DOUBLE
DOOR
SINGL E
DOOR
Before attaching oor decking, it is important to level and square the oor frame.
A level and square oor frame is required to correctly construct your shed.
BEGIN
1
See page 9 for the preferred oor leveling method.
2
Use level and check the frame is level before applying oor panels.
Check for frame squareness by measuring diagonally across corners. If the measurements are the
same, the frame is square. The diagonal measurement will be approximately 193-1/2" (491,5 cm).
When the frame is level and square secure one side of frame to the 4x4 runners using one fastener at
3
ends of each runner. Move to the opposite end of the frame. Secure the frame to 4x4 runners with one
fastener at ends of each runner making sure the frame remains square
FINISH
Once the oor frame is level and square fasten the frame to the 4x4 runners at each point the frame
4
contacts the 4x4 runners.
First, secure
at ends with
one fastener.
(Fig. A).
193-1/2"
(491,5 cm)
Fig. A
193-1/2"
(491,5 cm)
Second, secure
at ends with
one fastener.
12
FLOOR PANELS
PARTS REQUIRED:
x1
BEGIN
Ensure your oor frame is square by installing one panel and squaring frame.
Attach the 48 x 96" panel with the rough side up (painted-grid lines side) with the 48" edge and corner
1
ush to the oor frame (Fig A). Secure panel with two 2" nails in the corners.
Move to the opposite side.
2
Using the long edge of the panel as a lever,
move the panel side-to-side until the top corner is ush
to the oor frame (Fig. B).
Secure panel with two 2" nails in the corners.
5/8 x 48 x 96"
(1,6 x 121,9 x 243,8 cm)
Fig. A
Fig. B
x219
2" (5,1 cm)
(2) Nails
3/4"
(1,9 cm)
Flush
3
Continue attaching the panel using 2" nails 6" apart on edges and 12" apart inside panel.
Use a chalk line or use pre-painted grid lines to nail into joists under panel.
6"
(15,2 cm)
Grid lines up
2" (5,1 cm)
Nails
12"
(30,5 cm)
3/4"
(1,9 cm)
(2) Nails
Flush
Flush
13
Flush
FLOOR PANELS
PARTS REQUIRED:
x1
x2
4
Flush
Continue installing panels with rough side up (painted grid lines).
Use a chalk line or use pre-painted grid lines on panel for 2" nails 6" apart on edges,
and 12" apart inside panels.
23 -7/ 8"
(60,6 cm)
5/8" x 23-7/8" x 96" (1,6 x 60,6 x 243,8 cm)
5/8" x 48" x 96" (1,6 x 121,9 x 243,8 cm)
48"
(121,9 cm)
2" (5,1 cm)
48"
(121,9 cm)
12"
(30,5 cm)
Flush Flush Flush Flush
6"
(15,2 cm)
Grid lines up
FINISH
You have nished attaching your oor panels.
14
IMPORTANT!
DOUBLE
DOOR
SINGL E
DOOR
Check the oor frame is level after installing oor panels.
Re-level if needed.
HINT:
GABLE END
WALL
• The oor should be used as a stable work surface for wall construction.
• Organize your assembly procedure during the build process
to avoid over-handling of the walls.
BACK WALL
BACK WALL
FRONT WALL
(Your door location may vary.)
GABLE DOOR
WALL
15
RAFTER ASSEMBLY
¸
PARTS REQUIRED:
x3
CPA
2 x 4 x 8-1/2" (5,1 x 10,2 x 21,6 cm)
x6
You will build a rafter jig using the oor and three CPA parts as shown.
BEGIN
Secure one CPA ush to the oor deck using two 3" screws.
1
Measure over 96-3/4" and install a second CPA ush to the oor deck. CPA will overhang the oor.
Secure using two 3" screws.
Measure over 48" and up 35-3/16" from the oor edges and secure CPA using two 3" screws.
2
Check CPA is 35-3/16" at both ends for squareness.
96"
(243,8 cm)
Floor Width
Fig. A
CPA
48"
(122 cm)
3" (7,6 cm)
(2) 3" (7,6 cm)
Screws
in each CPA
Flush Flush
35-3/16"
(89,4 cm)
35-3/16"
(89,4 cm)
There will be an
overhang on
this end.
3/4"
(1,9 cm)
CPA CPA
96-3/4"
(245,7 cm)
IMPORTANT MEASUREMENT !!
Fig. B
FINISH
You have nished rafter jig. Proceed to assemble your rafters.
16
RAFTER ASSEMBLY
¸
PARTS REQUIRED:
x14
6 x 24" (15,2 x 61 cm)
x16
2 x 4 x 63-7/8" (5,1 x 10,2 x 162,2 cm)
OSB OR WOOD GRAIN
ASA
x 16
1-5/8" (4,1 cm)
x 168
2" (5,1 cm)
You will build 8 rafters - Six with 2 gussets and Two with only 1 gusset.
BEGIN
Place two rafters ASA into the jig as shown.
1
Keep ASA rm against outside CPA's as shown (Fig.A) and push rafters tight to the middle CPA . Rafters should
touch at tips (Fig. A).
Apply glue to rafters where gusset will attach (Fig. B).
Place gusset onto ASA holding a 1/4" gap from edge (Fig. C) and keeping rafters rm as instructed. Secure
gusset using one 1-5/8" screw into each rafter. HINT: These screws will help hold the measurements when you
nail on gussets.
Use ten 2" nails to nish securing the gusset to the rafters to pattern shown in Fig. C.
1/4" (1,9 cm)
GAP
Fig. A
1/4" (1,9 cm)
GAP
1-5/8" (4,1 cm)
Screw
ASA x2
Keep rafters rmly against CPA at both ends when securing gusset.
Flip rafters over and attach a second gusset using glue and (12) 2" nails. No need to use jig for this gusset.
2
3
Repeat Steps 1 - 2 to assemble fi v e more rafters with 2 gussets.
4
Repeat Step 1 to assemble two more rafters with only
Remove CPA's from oor.
1 gusset.
Fig. B
Glue where
gusset installs
ASA x2
96-3/4"
(245,7 cm)
1/4" (1,9 cm)
GAP
1/4" (1,9 cm)
GAP
FINISH
You have nished assembling your rafters.
Fig. C
17
GABLE DOOR WALL
PARTS REQUIRED:
x3
PWA
2 x 4 x 10" (5,1 x 10,2 x 25,4 cm)
x2
TK
2 x 4 x 80" (5 x 10,2 x 203,2 cm)
x1
SZ
2 x 4 x 89" (5 x 10,2 x 226,1 cm)
BEGIN
1
Orient parts on edge on oor. Measure and mark.
Use two 3" nails at each mark.
x2
AJ
2 x 4 x 12-1/2" (5,1 x 10,2 x 31,8 cm)
UX
x1
2 x 4 x 64" (5,1 x 10,2 x 162,6 cm)
89"
(226,1 cm)
77-1/4"
(196,2 cm)
68-1/2"
(174 cm)
SZ
x24
44-1/2"
(113 cm)
3" (7,6 cm)
HINT:
For easier nailing
stand on frame.
20-1/2"
(52,1 cm)
11- 3 /4 "
(29,8 cm)
10"
(25 ,4 cm)
PWA x3
3" (7,6 cm)
Nails
UX
80"
(203,2 cm)
TK
64"
(162,6 cm)
AJ AJ
Flush Flush
TK
12-1/2"
(31,8 cm)
12-1/2"
(31,8 cm)
18
GABLE DOOR WALL
PARTS REQUIRED:
x1
48 x 84"
(121,9 x 213,4 cm)
x1 LEFT + 1 RIGHT
2
Place left 48" x 84" panel onto wall frame ush to top of SZ with primed
side up as shown. Secure panel with 2" nails 6" (15,2 cm) apart.
Repeat Step 2 to attach the right 48" x 84" panel.
SZ
3-1/2"
(8,9 cm)
OO
1-1/4 x 2-1/2 x 69" (3,2 x 6,3 x 175,3 cm)
Temporary support
For squareness maintain ush
along panel edges.
48"
(121,9 cm)
3/4"
1,9 cm
x2
(121,9 cm)
Flush
3" (7,6 cm)
x52
2" (5,1 cm)
48"
3-1/2"
(8,9 cm)
6"
(15,2 cm)
Maintain 64" dimension
64"
Maintain
Flush
3" (7,6 cm)
Screws
(162,6 cm)
OO
3-1/2"
(8,9 cm)
Attach OO temporary support using 3" screws into wall frame as shown.
3
FINISH
Primed
side up
You have nished building your gable door wall.
Maintain
Flush
Primed
side up
3-1/2"
(8,9 cm)
19
STOP
AS YOU FACE THE FRONT WALL, CHOOSE YOUR SINGLE DOOR LOCATION -
LEFT OR RIGHT
The single door is a reversible door and can
either be left hand swing or right hand swing,
depending on your preference.
The graphics referenced in this instruction
show the door as a left hand swing.
If you install the door as a right hand swing,
simply mirror the left hand door instructions.
IF YOU CHOOSE TO LOCATE THE DOOR TOWARD THE LEFT
GO TO Page 21 TO BEGIN BUILDING YOUR WALL.
FRO NT WALL
OPTION 1:
DOOR LOCATION
LEFT SIDE OF FRONT WALL
GABLE WALL DOUBLE DOORSIMPORTANT:
If you choose to install your single door
on the right hand side of the shed and with
a right hand swing, note the double doors
and the single door will bump and interfere
with each other if opened at the same time.
Please be aware of this issue.
OPTION 2:
DOOR LOCATION
RIGHT SIDE OF FRONT WALL
IF YOU CHOOSE TO LOCATE THE DOOR TOWARD THE RIGHT
GO TO Page 27 TO BEGIN BUILDING YOUR WALL.
20
FRONT WALL WITH DOOR LEFT
PARTS REQUIRED:
AO
x4
2 x 4 x 22-1/2" (5,1 x 10,2 x 57,1 cm)
x4
TK
2 x 4 x 80" (5,1 x 10,2 x 203,2 cm)
You will build two window frame assemblies (Fig.A).
BEGIN
1
Orient parts on edge on oor. Measure and mark.
Use two 3" nails at each mark.
22-1/2 "
(5 7,1 c m)
x16
3" (7,6 cm)
HINT:
For easier nailing
stand on frame.
3" (7,6 cm)
Nails
Fig. A
AO
80"
(203,2 cm)
TK
1-1/2"
(3,8 cm)
2
Repeat Step 1 to build second window frame.
70"
(177, 8 c m)
40"
(101, 6 c m)
FINISH
4
You have nished your window frame assemblies.
21
FRONT WALL WITH DOOR LEFT
PARTS REQUIRED:
x1
QT
2 x 4 x 35" (5,1 x 10,2 x 88,9 cm)
x1
TM
2 x 4 x 72" (5,1 x 10,2 x 182,9 cm)
x7
TK
2 x 4 x 80" (5,1 x 10,2 x 203,2 cm)
x2
TP
2 x 4 x 96" (5,1 x 10,2 x 243,8 cm)
BEGIN
Orient parts on edge on oor. Measure and mark.
1
Use two 3" nails at each mark and four 3" nails at seams.
72"
(182,9 cm)
54-1/4"
(137,8 cm)
48"
(121,9 cm)
24"
(61 cm)
17-3 /4"
(4 5,1 cm)
x2
ABA
2 x 4 x 20" (5,1 x 10,2 x 50,8 cm)
(396,2 cm)
144"
96"
(243,8 cm)
(365,8 cm)
TP
156"
x42
x2
CPA
2 x 4 x 8-1/2" (5,1 x 10,2 x 21,6 cm)
168"
(426,7 cm)
3" (7,6 cm)
72"
(182,9) cm)
HINT:
For easier nailing
stand on frame.
TM
80"
(203,2 cm)
ABA
CPA
1-1/2"
(3,8 cm)
QT
35"
(88,9 cm)
(3,8 cm)
1-1/2"
ABA
20"
(50,8 cm)
3" (7,6 cm)
Nails
TOENAILING
1-1/2"
(3,8 cm)
Two 3" Nails at
each location.
TK x7
3" (7,6 cm)
Nails
TP
96"
(243,8 cm)
22
FRONT WALL WITH DOOR LEFT
PARTS REQUIRED:
x2
x1
x2
x2
CPA
2 x 4 x 8-1/2" (5,1 x 10,2 x 21,6 cm)
QT
2 x 4 x 35" (5,1 x 10,2 x 88,9 cm)
YFA
2 x 4 x 68-1/2" (5,1 x 10,2 x 174 cm)
TK
2 x 4 x 80" (5,1 x 10,2 x 203,2 cm)
Place Sub-Assembly in frame as shown. Measure and mark.
2
Use two 3" nails at each mark and four 3" nails at seam.
3
Orient door frame parts on edge on oor as shown. Measure and mark.
Install QT fi rst. Use two 3" nails at each mark as shown.
83-1/4"
(211,5 cm)
60"
12"
(30,5 cm)
(152,4 cm)
108"
(274,3 cm)
120"
(337,2 cm)
Hold Seam
132-3/4"
(304,8 cm)
TK
Flush
x60
Window Frame Assembly
x2
3" (7,6 cm)
Window Frame
Assemblies
HINT:
For easier nailing
stand on frame.
QT
Install QT rst!
TK
YFA
32"
(81,3 cm)
FINISH
You have nished your front wall frame.
3" (7,6 cm)
Nails
TOENAILING
Two nails at
each location.
3" (7,6 cm)
Nails
23
CPA
108"
(274,3 cm)
84-3/4"
(215,3 cm)
59-1/4"
(151,5 cm)
35-1/4"
(89,5 cm)
FRONT WALL WITH DOOR LEFT
PARTS REQUIRED:
x63
GAA
3/4" GAUGE
BLOCK
3/8 x 48 x 84"
x1
BEGIN
Place 48" x 84" window panel onto wall frame ush to top of frame with primed side up as shown.
1
(1 x 121,9 x 213,4 cm)
Use the gauge block to mark the 3/4" measurement on the wall stud.
Secure panel with 2" nails 6" apart on edges and 12" apart inside panel.
BEGIN HERE
For squareness maintain Flush at
top of panel and 3/4" measurement
along panel edge.
3/4"
(1,9 cm)
Flush
Primed
side up
2" (5,1 cm)
12"
(30,5 cm)
3/4" GAUGE
BLOCK
3/8 x 48 x 84"
(1 x 121,9 x 213,4 cm)
6"
(15,2 cm)
24
FRONT WALL WITH DOOR LEFT
PARTS REQUIRED:
x1
2
Place 48 x 84" single door panel onto wall frame ush to top of frame with primed side up as shown.
Use the gauge block to mark the 3/4" measurement on the wall stud.
Secure panel with 2" nails 6" apart on edges
For squareness maintain ush and
3/4" measurement along panel edge.
3/4"
(1,9 cm)
3/8 x 48 x 84"
(1 x 121,9 x 213,4 cm)
Flush
x66
2" (5,1 cm)
GAA
3/4" GAUGE
BLOCK
3/8 x 48 x 84"
(1 x 121,9 x 213,4 cm)
3/4" GAUGE
BLOCK
Primed
side up
Flush
6"
(15,2 cm)
Flush
25
Loading...