Yardistry components are intended for privacy, decorative and ornamental use only.
Product is NOT INTENDED for the following:
• A safety barrier to prevent unsupervised access to pools, hot tubs, spas or ponds.
• As load bearing support for a building, structure, heavy objects or swings.
• Used in structures that trap wind, rain or snow that would create extra load on the
product.
Accumulated snow must be removed from roof.
DO NOT climb or walk on roof for any reason.
Permanent structures may require a building permit. As the purchaser and or installer of this
product you are advised to consult local planning, zoning and building inspection departments for
guidance on applicable building codes and/or zoning requirements.
Wood is NOT ame retardant and will burn. Grills, re pits and chimineas are a re hazard if
placed too close to a Yardistry structure. Consult user’s manual of the grill, re pit or chimnea for
safe distances from combustible materials.
Wear gloves to avoid injury from possible sharp edges of individual elements before assembly.
During installation, follow all safety warnings provided with your tools and use OHSA
approved safety glasses. Some structures may require two or more people to install safely.
Check for underground utilities before digging or driving stakes into the ground!
It is important during assembly to closely follow the instructions, complete the assembly
on a solid level surface and that you follow the instruction to square up, level and anchor the
structure, this will reduce the gap at wood connections during assembly.
General Information
General Information: Wood components are manufactured with Cedar (C. Lanceolata)
which is protected with factory applied water-based stain. Knots, small checks (cracks)
and weathering are naturally occurring and do not affect the strength of the product.
Annual application of a water-based water repellent sealant or stain is important and will
help reduce weathering and checks.
www.yardistrystructures.com
Questions?
Call toll free or write us at:
1 (888) 509-4382
info@yardistrystructures.com
Patents Pending
2 support@yardistrystructures.com
Limited Warranty
Yardistry warrants that this product is free from defect in materials and workmanship for a
period of one (1) year from the original date of purchase. In addition, for any product with
lumber, all lumber is warranted for ve (5) years against rot and decay. This warranty applies
to the original owner and registrant and is non-transferable.
Regular maintenance is required to assure the integrity of your product and is a requirement of
the warranty. This warranty does not cover any inspection costs.
This Limited Warranty does not cover:
• Labour for replacment of any defective item(s);
• Incidental or consequential damages;
• Cosmetic defects which do not affect performance or integrity;
• Vandalism; improper use or installation; acts of nature, including but not limited to wind,
storms, hail, oods, excessive water exposure;
• Minor twisting, warping, checking or any other natural occurring properties of wood that do
not affect performance or integrity.
Yardistry products have been designed for safety and quality. Any modications made to
the original product could damage the structural integrity of the product leading to failure
and possible injury. Yardistry cannot assume any responsibility for modied products.
Furthermore, modication voids any and all warranties.
This product is warranted for RESIDENTIAL USE ONLY. Yardistry disclaims all other
representations and warranties of any kind, express or implied.
This Warranty gives you specic legal rights. You may have other rights as well which vary from state to state
or province to province. This warranty excludes all consequential damages, however, some states/provinces
do not allow the limitation or exclusion of consequential damages, and therefore this limitation may not apply
to you.
3 support@yardistrystructures.com
Instructions for Proper Maintenance
Your Yardistry structure is designed and constructed of quality materials. As with all outdoor
products it will weather and wear. To maximize the enjoyment, safety and life of your structure
it is important that you, the owner, properly maintain it.
HARDWARE:
• Check metal parts for rust. If found, sand and repaint using a non-lead paint complying
with 16 CFR 1303.
• Inspect and tighten all hardware after completion of assembly; after rst month of use; and
then annually. Do not over-tighten as to cause crushing and splintering of wood.
• Check for sharp edges or protruding screw threads, add washers if required.
WOOD PARTS:
• Applying a water repellent or stain (water-based) on a yearly basis is important
maintenance to maintain maximum life and performance of the product.
• Check all wood members for deterioration, structural damage and splintering. Sand down
splinters and replace deteriorated wood members. As with all wood, some checking and
small cracks in grain is normal
• Some gapping may occur at some wood connections.
Assembly Guides
Tools Required:
• Tape Measure
• Carpenters Level
• Standard or Cordless Drill
• #2 Phillips Bit or Screwdriver
• 7/16” & 9/16” Wrench
Symbols:
Throughout these instructions symbols are provided in the top, right-hand corner of the page.
• Use Help, where this is shown, 2, 3 or 4
people are required to safely complete
this step. To avoid injury or damage to the
assembly make sure to get some help.
• Pre-drill a pilot hole before fastening
screw or lag to prevent splitting of wood.
• 8’ Step Ladder
• Safety Glasses
• Adult Helper
• Safety Gloves
• Hard Hat
• 6’ Step Ladder x 2
• Square
• Ratchet
• 7/16, 1/2 & 9/16 Socket
• Use a measuring tape to assure proper
location
If you dispose of your Yardistry structure: Please disassemble and dispose of your
unit so that it does not create any unreasonable hazards at the time it is discarded. Be
sure to follow your local waste ordinances.
4 support@yardistrystructures.com
Assembly Tips
Following are some helpful tips to make the assembly process smooth and efcient.
PRE-ASSEMBLIES:
(i.e. Post and Beam Assemblies, Roof Rafter Assembly, etc)
• Work on a raised, solid and at surface such as, a table or saw horse.
• Keep all connections ush where shown in the instructions.
• When assembling the beams keep parts at, straight and snug when
connecting.
METAL PARTS:
• Roong material may have sharp edges, wear safety gloves.
• Remove all plastic covering, on both sides of the metal panels, directly
before installing each piece.
• Place roong material on a non-abrasive surface before and after assembly
as it can bend, dent and scratch easily.
• The roong screws can easily crush the roof panels and roof edges when
using a power drill. We recommend hand tightening the roong screws so
they sit snug and tight to the roong material.
5 support@yardistrystructures.com
Permanent Installation Examples
Note: It is critically important you start with square, solid and level footings, concrete
pad or deck to attach your Pergola Room.
We supply Post Mounts with this structure which gives you the exibility to permanently install your structure
to a pre-existing or new wood or concrete surface.
• The hardware to attach the Post Mount to the structure is included.
• The hardware to mount the structure permanently will need to be purchased separately at your local
hardware store.
If you are mounting to concrete footers see below for the correct locations and placement. Please double
check for possibility of any underground utilities such as gas, telephone, cable or sprinkler lines.
Following are some examples of how to mount the structure to wood or concrete surfaces.
Refer to your local building and city codes, ordinances, neighbourhood covenants, or height restrictions
regarding this type of structure for guidance on acceptable installation requirements.
Concrete Footer
9’ 1-7/8”
2.791 m
Post to Post
Post Mount
8’ 1-3/8”
2.473 m
Plinth to Plinth
Post to Post
9’ 1-7/8”
2.791 m
11’ 7-7/8”
3.553 m
Post to Post
Anchoring Hardware not included
To
Required
Depth
Plinth to Plinth
8’ 1-3/8”
2.473 m
6 support@yardistrystructures.com
Permanent Installation Examples cont.
Concrete Patio [min. 10’ 1-7/8” x 10’ 1-7/8” (3.096 m x 3.096 m)] with 6” (1.83 m) clearance on all sides
Anchoring Hardware not included
Wood Deck [min. 10’ 1-7/8” x 10’ 1-7/8” (3.096 m x 3.096 m)] with 6” (1.83 m) clearance on all sides
Anchoring Hardware not included
Post Mount
Anchoring Hardware (not included)
7 support@yardistrystructures.com
Part Identification ( )
Dimensions are approximate and are shown to assist in the identification of parts for
assembly. Actual dimensions may be smaller or larger.
139.7 x 139.7 x 2235.2mm (5½ x 5½ x 88")
4pc. (752) -
Y70131-752
Post
34.9 x 165.1 x 926.9mm (1-3/8 x 6-1/2 x 36-1/2")
4pc. (740) -
Short Right Gusset
Y70131-740
31.8 x 127 x 385.8mm (1-1/4 x 5 x 15-3/16")
8pc. (727) -
Inside Short Beam
Y50131-727
31.8 x 127 x 2235.2mm (1-1/4 x 5 x 88")
4pc. (728) -
Inside Long Beam
Y50131-728
31.8 x 127 x 1497mm (1-1/4 x 5 x 58-15/16")
4pc. (726) -
Right Outside Beam
Y50131-726
31.8 x 127 x 1497mm (1-1/4 x 5 x 58-15/16")
4pc. (725) -
Left Outside Beam
Y50131-725
34.9 x 165.1 x 926.9mm (1-3/8 x 6-1/2 x 36-1/2")
4pc. (739) -
Short Left Gusset
Y70131-739
19.1 x 127 x 177.8mm (3/4 x 5 x 7")
16pc. (738) -
Plinth
Y50131-738
28.6 x 69.9 x 2234.5mm (1-1/8 x 2-3/4 x 88")
4pc. (733) -
Strap Long
Y50131-733
28.6 x 69.9 x 1112.5mm (1-1/8 x 2-3/4 x 43-3/4")
4pc. (732) -
Short Strap
Y50131-732
28.6 x 69.9 x 1570mm (1-1/8 x 2-3/4 x 61-13/16")
4pc. (736) -
Rafter
Y50131-736
25.4 x 80 x 2137mm (1 x 3-1/8 x 84-1/8")
4pc. (737) -
Corner RT
Y50131-737
25.4 x 80 x 2137mm (1 x 3-1/8 x 84-1/8")
4pc. (729) -
Corner LT
Y50131-729
28.6 x 69.9 x 1530.8mm (1-1/8 x 2-3/4 x 60-1/4")
4pc. (731) -
Fascia Left Short
Y50131-731
28.6 x 69.9 x 1530.8mm (1-1/8 x 2-3/4 x 60-1/4")
4pc. (730) -
Fascia Right Short
Y50131-730
28.6 x 69.9 x 858mm (1-1/8 x 2-3/4 x 33-3/4")
4pc. (735) -
Rafter Short Left
Y50131-735
28.6 x 69.9 x 858mm (1-1/8 x 2-3/4 x 33-3/4")
4pc. (734) -
Rafter Short Right
Y50131-734
8 support@yardistrystructures.com
Hardware Identification ( )
4pc.
- Short Panel Left
(Y01033-223)
Dimensions are approximate and are shown to assist in the identification of
parts for assembly. Actual dimensions may be smaller or larger.
4pc.
- Long Panel Right
(Y01033-224)
4pc.
- Long Panel Left
(Y01033-222)
8pc.
Ridge Clip 85.25 - (Y01033-227)
4pc.
Ridge Cap 85 - (Y01033-231)
4pc.
Roof Edge Right 59 7/16 - (Y01033-229)
4pc.
Roof Edge Left 59-7/16 - (Y01033-228)
Bracket LT Set (2Pk)
1pc.
- Weather Seal
Ridge Clip 85¼ (8Pk)
(Y70818-232)
1pc.
- Gazebo ID Plaque
(Y70800-104)
1pc.
Mount Set (8Pk)
- Post
(Y70819-109)
2pc.
Hook
(Y00418-050)
1pc.
- 45º Twist
(Y70829-191)
1pc.
- Corner Cap Set (4Pk)
(Y70833-226)
- 50mm
4pc.
(Y01000-094)
1pc.
- Rafter/Beam
Bracket Set (12Pk)
(Y70829-230)
- Short Panel Right
(Y01033-225)
1pc.
Bracket RT Set (2Pk)
(Y70829-192)
1pc.
Carriage Bolt
(Y07490-260)
1pc.
Peak Post
(Y09490-001)
1pc.
Peak Cap
(Y01033-095)
- 45º Twist
1pc.
Spring Clip
1pc.
1/4" Nut
(Y08490-200)
1pc.
- Roof Peak Set
(Y70829-221)
1pc.
- Roof Panel Set
(Y70833-233)
2pc.
Roof Peak Bracket
(Y00429-068)
1pc.
Peak Loop
(Y20018-003)
9 support@yardistrystructures.com
Hardware Identification ( )
Dimensions are approximate and are shown to assist in the identification of
parts for assembly. Actual dimensions may be smaller or larger.
12pc.
1/4 x 2-3/4 Hex Bolt - (Y07718-223)
12pc.
1/4 x 2" Hex Bolt - (Y07718-220)
16pc.
8pc.
24pc.
98pc.
Hex Bolt
Lag Screw
Lag Screw
Pan Screw
5/16 x 3-1/4"
5/16 x 4-3/4"
1/4" x 1-15/16" No.12 Shank
#10 x 1-1/4"
- (Y07718-331)
- (Y06218-343)
(Y06491-711)
36pc.
Hex Bolt
- (Y06218-219)
160pc.
Wood Screw
5/16 x 1-1/4" - (Y07718-311)
1
p
(
c
Y
.
0
-
0
1
4
/
0
8
0
"
-
D
0
0
r
ill
2
)
B
it
#8 x 1-1/2"
(Y06091-512)
72pc.
Wood Screw
24pc.
Wood Screw
3/8 x 1-1/4" Large Washer
16pc.
(Y05118-811)
#8 x 2 1/4"
#8 x 2" - (Y06091-520)
- (Y06091-521)
24pc.
- 1/4" Lock Nut
(Y08318-203)
8pc.
- 3/8" Lock Nut
(Y08318-803)
32pc.
(Y06091-003)
Wood Screw #7 x 3/4"
1pc.
- Hex Driver (Y00400-004)
1pc.
#2 x 2" Robertson Driver (Y00400-005)
168pc.
Hex Roofing Screw
#8x 1"
(Y06733-510)
8pc.
52pc.
5/16" Lock Washer
(Y05318-300)
24pc.
Sheet Metal Screw
Hex Bolt
3/8 x 8-1/2"
(Y07718-882)
#8 x 3/4"
52pc.
1/4-5/16 x 1-1/4" Large Washer
132pc.
(Y05118-311)
10 support@yardistrystructures.com
(
Y06433-503)
5/16 - T-Nut
(Y08518-300)
Step 1: Inventory Parts - Read This Before Starting Assembly
STOPSTOPSTOPSTOP
A. This is the time for you to inventory all your hardware, wood and accessories,
referencing the parts identication sheets. This will assist you with your assembly.
• Each step indicates which bolts and/or screws you will need for assembly, as well as
any at washers, lock washers, t-nuts or lock nuts.
B. If there are any missing or damaged pieces or you need assistance with
assembly please contact the consumer relations department directly. Call us
before going back to the store.
1-888-509-4382
support@yardistrystructures.com
C. Read the assembly manual completely, paying special attention to ANSI warnings;
notes; and safety/maintenance information on pages 1 - 4.
• Follow the instructions in order.
• This structure is designed to be assembled and installed ideally by four people,
DO NOT attempt to install alone.
• Consider the slope of elevation where you plan to install the structure. Also, check for
gas, telephone, other utilities or sprinkler line locations prior to excavating any holes.
D.Before you discard your cartons ll out the form below.
• The carton I.D. stamp is located on the end of each carton.
• Please retain this information for future reference. You will need this information if you
contact the Consumer Relations Department.
PRODUCT NUMBER: YM11756
CARTON I.D. STAMP: __ __ __ __ __ ___ (Box 1)
CARTON I.D. STAMP: __ __ __ __ __ ___ (Box 2)
CARTON I.D. STAMP: __ __ __ __ __ ___ (Box 3)
11 support@yardistrystructures.com
Step 2: Post Assemblies
A: At the bottom of each (752) Post insert two 5/16” T-Nuts as shown in g. 2.1 and 2.2.
B: At the bottom of each (752) Post place two Post Mounts tight to the bottom and inside faces as shown in g. 2.1
and 2.2. Loosely attach with one 5/16 x 1-1/4” Hex Bolt (with 5/16” lock washer and 1/4-5/16” large washer) per
mount so they connect to the T-Nuts.
C: On each side of the Posts, place one (738) Plinth ush to the bottom and attach with four #8 x 1-1/2” Wood
Screws per plinth. Rounded edges on top. (g. 2.1 and 2.3)
D: From the bottom of each Post Mount attach to posts with two #8 x 1-1/2” Wood Screws per mount and then from
the inside with two #10 x 1-1/4” Pan Screws per mount These screws are installed at a slight angle. Tighten all
bolts. There will be four Post Assemblies. (g. 2.4)
Fig. 2.1
Top
(752)
Post
(752)
Post
Post
Mount
5/16 x 1-1/4”
Hex Bolt
5/16” Lock
Washer
Fig. 2.4
1/4 - 5/16”
Large Washer
Fig. 2.2
5/16” T-Nut (x 2
per Post)
Post
Mount
(752)
Post
Fig. 2.3
Rounded
Edge on Top
(738) Plinth
#8 x 1-1/2”
Wood Screws
(x 4 per Plinth)
(752)
Post
Post
Mount
Post
Mount
Bottom
#10 x 1-1/4” Pan Screws (x 2
per Post Mount, from inside)
#8 x 1-1/2” Wood Screws
(x 2 per Post Mount, from
bottom)
HardwareWood Parts
4 x (752) Post
16 x (738) Plinth
16 x #10 x 1-1/4” Pan Screw
80 x #8 x 1-1/2” Wood Screw
8 x Post Mount
8 x 5/16” T-Nut
8 x 5/16 x 1-1/4” Hex Bolt
(with 5/16” lock washer, 1/4-5/16” large washer)
12 support@yardistrystructures.com
3
3
Step 3: Beam Assembly
Part 1
A: Connect one (725) Left Outside Beam and one (726) Right Outside Beam using two 5/16 x 1-1/4” Hex Bolts
(with 5/16” lock washer, 1/4 - 5/16” large washer and 5/16” t-nut) as shown in g. 3.1 and 3.2.
B: Connect one (727) Inside Short Beam to each end of one (728) Inside Long Beam using two 5/16 x 1-1/4”
Hex Bolts (with 5/16” lock washer, 1/4 - 5/16” large washer and 5/16” t-nut) per end as shown in g. 3.1 and 3.2.
C: Repeat Steps A and B three more times to make four Outside Beam Assemblies and four Inside Beam
Assemblies.
(727) Inside
Short Beam
(728) Inside
Long Beam
(725) Left
Outside Beam
Fig. 3.1
Fig. 3.2
5/16 x 1-1/4”
Hex Bolt
Tight
5/16” Lock
Washer
(727) Inside
Short Beam
5/16”
T-nut
(726) Right
Outside Beam
Make sure bolt heads
are on the outside of
each Beam Assembly
1/4 -5/16”
Large Washer
Wood Parts
4 x (725) Left Outside Beam
4 x (726) Right Outside Beam
8 x (727) Inside Short Beam
4 x (728) Inside Long Beam
13 support@yardistrystructures.com
24 x 5/16 x 1-1/4” Hex Bolt
(5/16” lock washer, 1/4-5/16” large washer, 5/16” t-nut)
Hardware
Step 3: Beam Assembly
Part 2
D: Place one Outside Beam Assembly on one Inside Beam Assembly so the ends are ush. Match the bolt
holes in each (727) Inside Short Beam and (728) Inside Long Beam with the bolt holes in (725) Left Outside
Beam and (726) Right Outside Beam. Attach with 13 #8 x 2-1/4” Wood Screws. (g. 3.3 and 3.4)
E: Repeat Step D three more times to make four Beam Assemblies.
(727)
Outside Beam
Fig. 3.3
Assembly
(727)
(728)
Inside Beam
Assembly
Flush
Flush
Match bolt holes
Outside Beam
Assembly
Fig. 3.4
#8 x 2-1/4” Wood Screws
(x 13 per assembly)
Inside Beam
Assembly
Hardware
52 x #8 x 2-1/4” Wood Screw
14 support@yardistrystructures.com
Loading...
+ 30 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.