Yardistry YM11645 Installation And Operating Instructions

12 x 14 Arched Roof Pergola

4.73M

12 x 14 Arched Pergola Room

YM11645

3.7 M

12ft

14 ft

Installation and Operating Instructions – YM11645

Yardistry – North America

Toll Free Customer Support: 1.888.509.4382

[e-mail]
www.yardistrystructures.com

Yardistry / Selwood Products – Europe

Customer Support: [phone]

[e-mail]

www.selwoodproducts.com

1 [e-mail]

Revised 04/08/2013

HEIGHT:

8’ 8or 2.63m

Important Safety Notice!

Yardistry components are intended for privacy, decorative and ornamental use only.

Product is NOT INTENDED for the following:

• A safety barrier to prevent unsupervised access to pools, hot tubs, spas or ponds.

• As load bearing support for a building, structure, heavy objects or swings.

• Used in structures that trap wind, rain or snow that would create extra load on the
product.

Permanent structures may require a building permit. As the purchaser and or installer
of this product you are advised to consult local planning, zoning and building inspection
departments for guidance on applicable building codes and/or zoning requirements.

Wood is NOT ame retardant and will burn. Grills, re pits and chimineas are a re
hazard if placed too close to a Yardistry structure. Consult user’s manual of the grill, re

pit or chimnea for safe distances from combustible materials.

Wear gloves to avoid injury from possible sharp edges of individual elements before
assembly.

During installation, follow all safety warnings provided with your tools and use
OHSA approved safety glasses. Some structures may require two or more people to

install safely.

Check for underground utilities before digging or driving stakes into the ground!

.

General Information

General Information: Wood components are manufactured with Cedar (C. Lanceolata)

which is protected with factory applied water-based stain. Knots, small checks (cracks)
and weathering are naturally occurring and do not affect the strength of the product.
Annual application of a water-based water repellent sealant or stain will help reduce
weathering and checks.

www.yardistrystructures.com

Questions?

Call toll free or write us at:

1 [phone]

[e-mail]

Patents Pending

2 [e-mail]

Limited Warranty

Yardistry warrants that this product is free from defect in materials and workmanship
for a period of one year from the original date of purchase. In addition, all lumber is
warranted for 5 years against rot and decay. This warranty applies to the original owner
and registrant and is non-transferable.

Regular maintenance is required to assure the integrity of your product and is a requirement of
the warranty. This warranty does not cover any inspection cost.

This Limited Warranty does not cover:

• Labor for replacement of any defective item(s);

• Incidental or consequential damages;

• Cosmetic defects which do not affect performance or integrity;

• Vandalism; improper use or installation; acts of nature;

• Actsofnatureincludingbutnotlimitedtowind,storms,hail,oods,excessivewater 
 exposure;

• Minor twisting, warping, checking, or any other natural occurring properties of wood that

do not affect performance or integrity.

Yardistryproductshavebeendesignedforsafetyandquality.Anymodicationsmadetothe

original product could damage the structural integrity of the product leading to failure and

possibleinjury.Yardistrycannotassumeanyresponsibilityformodiedproducts.Furthermore,
modicationvoidsanyandallwarranties.

This product is warranted for RESIDENTIAL USE ONLY. Yardistry disclaims all other
representations and warranties of any kind, express or implied.

This Warranty gives you specic legal rights. You may have other rights as well which vary from state to state or province to
province. This warranty excludes all consequential damages, however, some states do not allow the limitation or exclusion of
consequential damages, and therefore this limitation may not apply to you.

3 [e-mail]

Instructions for Proper Maintenance

Your Yardistry structure is designed and constructed of quality materials. As with all outdoor
products it will weather and wear. To maximize the enjoyment, safety and life of your structure
it is important that you, the owner, properly maintain it.

HARDWARE:

• Check metal parts for rust. If found, sand and repaint using a non-lead paint complying
with 16 CFR 1303.

• Inspect and tighten all hardware after completion of assembly; after rst month of use; and

then annually. Do not over-tighten as to cause crushing and splintering of wood.

• Check for sharp edges or protruding screw threads, add washers if required.

WOOD PARTS:

• Unprotected they will appear weathered over time. Periodic application of an exterior
water repellent or stain (water-based) will help improve appearance and life.

• Check all wood members for deterioration, structural damage and splintering. Sand down
splinters and replace deteriorated wood members. As with all wood, some checking and
small cracks in grain is normal

Assembly Guides

Tools Required:

• Tape Measure

• Carpenters Level

• Standard or Cordless Drill

• #2 Phillips Bit or Screwdriver

• 7/16” Wrench or Socket

Symbols:

Throughout these instructions symbols are provided in the top, right-hand corner of the page.

• Use Help, where this is shown, 2 or 3 people
are required to safely complete this step.
To avoid injury or damage to the assembly
make sure to get some help.

• Pre-drill a pilot hole before fastening
screw or lag to prevent splitting of wood.

• 8’ Step Ladder

• Safety Glasses

• Adult Helper

• Gloves

• Hard Hat

• Use a measuring tape to assure proper

location

If you dispose of your Yardistry structure: Please disassemble and dispose of your
unit so that it does not create any unreasonable hazards at the time it is discarded. Be
sure to follow your local waste ordinances.

4 [e-mail]

Permanent Installation Examples

20 3/4"

169 11/16"

120"

120"

78 1/2"

78 1/2"

Note: It is critically important you start with square, solid and level footings, concrete
pad or deck to attach your Pergola Room.

We supply Room L-Mounts with this structure which gives you the exibility to permanently install your

structure to a pre-existing or new wood or concrete surface.

• The hardware to attach the Room L-Mount to the structure is included.

• The hardware to mount the structure permanently will need to be purchased separately at your local

hardware store.

If you are mounting to concrete footers see below for the correct locations and placement. Please double
check for possibility of any underground utilities such as gas, telephone, cable or sprinkler lines.

Following are some examples of how to mount the structure to wood or concrete surfaces.

Refer to your local building and city codes, ordinances, neighbourhood covenants, or height restrictions
regarding this type of structure for guidance on accepable installation requirements.

Concrete Footer

Corner Post

Panel Post

2 3/4” 1”

Room L - Mount

Anchoring Hardware not included

16 1/8” - Groove

Room L - Mount

#10 x 1-1/4” Pan Screws Included

1/2

1

”

Panel Post

To
Required
Depth

5 [e-mail]

Permanent Installation Examples cont.

Concrete Patio (min. 10’ 2” x 10’ 2”) with 12” clearance on all sides

#10 x 1-1/4” Pan Screws Included

Anchoring Hardware not included

Wood Deck (min. 10’ 2” x 10’ 2”) with 12” clearance on all sides

#10 x 1-1/4” Pan Screws Included

Anchoring Hardware not included

Post

#10 x 1-1/4”
Pan Screw

Room L-Mount

6 [e-mail]

Beam 20-3/4" (067)

Arch Beam Offset (080)

Arch Beam Front (195)

Arch Beam Centre (079)

Trellis End Short (233)

Corner Post Long

(235)

Long (237)

Arch Gusset Right

L Mount Left

L Mount Right

Beam End 34-1/4" (192)

Beam 105-1/2" (234)

Plinth Short A Assembly (027)

Plinth Short B Assembly (028)

Plinth End Assembly (029)

Arch Gusset Left Long(236)

Plinth Long Assembly (026)

X Insert (183)

Arch Gusset Left

(194)

Trellis End Long (232)

Arch Gusset Right (193)

Cross Brace Insert (189)

Horizontal Insert (185)

Bottom Brace Insert (191)

2 x 3 Trellis Clip

Beam Hanger

Support Beam 105-1/2" (231)

Beam End

10-1/2" (069)

7 [e-mail]

Engineered Panel Post Long (241)

Engineered Panel Corner Post Long (239)

Part Identification ( )

Dimensions are approximate and are shown to assist in the identification of parts for
assembly. Actual dimensions may be smaller or larger.

38.1 x 38.1 x 409.6mm

32pc. (185) -

Horizontal Insert 2 x 2 x 16-1/8" - Box 1

64pc. (183) - X

9pc. (233) -

9pc. (232) -

8pc. (189) -

8pc. (241) -

38.1 x 38.1 x 574.7mm
Insert 2 x 2 x 22-5/8" - Box 1,2,3

38.1 x 63.5 x 1699.7mm

Trellis End Short 2 x 3 x 66 15/16" - Box 2

38.1 x 63.5 x 2554.8mm

Trellis End Long 2 x 3 x 100 -5/8 - Box 1

38.1 x 76.2 x 409.6mm

Cross Brace Insert 2 x 4 x 16-1/8" - Box 3

36 x 69.9 x 2463.8mm

Engineered Panel Post Long 2 x 4 x 97" - Box 2

2pc. (194) -

4pc. (069) -

2pc. (237) -

53.5 x 69.9 x 2463.8mm

8pc. (239) -

36 x 127 x 453.2mm

Arch Gusset Left 2 x 5 x 17-27/32" - Box 3

38.1 x 139.7 x 266.7mm

Beam End 10-1/2" 2 x 6 x 10-1/2" - Box 3

36 x 139.7 x 762mm

Arch Gusset Right Long 2 x 6 x 30" - Box 1

Engineered Panel Corner Post Long 2 x 4 x 97" - Box 2

2pc. (193) -

8pc. (191) -

2pc. (236) -

36 x 127 x 453.2mm

Arch Gusset Right 2 x 5 x 17-27/32" - Box 3

38.1 x 69.9 x 408.9mm

Bottom Brace Insert 2 x 4 x 16-1/8" - Box 3

36 x 139.7 x 762mm

Arch Gusset Left Long 2 x 6 x 30" - Box 1

8 [e-mail]

Part Identification ( )

Dimensions are approximate and are shown to assist in the identification of parts for
assembly. Actual dimensions may be smaller or larger.

4pc. (067) -

38.1 x 139.7 x 527.1mm

Beam 20-3/4" 2 x 6 x 20-3/4" - Box 3

38.1 x 139.7 x 1866.9mm

4pc. (231) -

Support Beam 2 x 6 x 73-1/2" - Box 2

38.1 x 241.3 x 3048.0mm

2pc. (195) -

2pc. (080) -

Arch Beam Front - Box 3

38.1 x 241.3 x 3048.0mm
Arch Beam Offset - Box 3

4pc. (192) -

38.1 x 139.7 x 870mm

Beam End 34-1/4" 2 x 6 x 34-1/4" - Box 3

8pc. (029) -

34.9 x 152.4 x 141.3mm

2pc. (079) -

2pc. (234) -

4pc. (235) -

Plinth End Assembly - Box 1

38.1 x 241.3 x 3048.0mm

Arch Beam Centre - Box 3

38.1 x 139.7 x 2679.7mm
Beam 105-1/2" 2 x 6 x 105-1/2" - Box 1

69.9 x 69.9 x 2463.8mm
Corner Post Long 3 x 3 x 97" - Box 2

4pc. (027) -

34.9 x 152.4 x 492.1mm
Plinth Short A Assemlby - Box 1

34.9 x 152.4 x 598.5mm

8pc. (026) -

9 [e-mail]

Plinth Long Assembly - Box 1

4pc. (028) -

34.9 x 152.4 x 492.1mm
Plinth Short B Assembly - Box 1

Hardware Identification ( )

Dimensions are approximate and are shown to assist in the identification of
parts for assembly. Actual dimensions may be smaller or larger.

9pc. H2

4pc.

G10

4pc. G5

8pc.

G22

4pc.

z

- Hex Bolt

- Hex Bolt

- Hex Bolt

- Hex Bolt

- Hex Bolt

1/4 x 2" - (Y07416-920)

5/16 x 3" - (Y07416-330)

5/16 x 4-1/2"

- (Y07416-342)

5/16 x 5" - (Y07416-350)

5/16 x 6"

- (Y07416-360)

94pc. -S12

113pc. S24

152pc.

90pc.

18pc.

FW1

(Y05416-201)

Pan Screw

- Wood Screw

S4

- Wood Screw

S3

Wood Screw

- 1/4" Flat Washer

#10 x 1-1/4"

- (Y06416-911)

#10 x 4" - (Y06416-940)

#8 x 3" - (Y06416-530)

#8 x 2 1/2"

- (Y06416-522)

D4

1pc.

- #2 x 2" Roberston Driver (9200014)

96pc.

TS Trim Screw #6 x 30mm - (Y06416-930)

-

9pc.

- 1/4" Lock Nut

(Y08416-202)

1
p

(

c

Y

.

0

-

0

1

4

/

0

8

0

"

-

D

0

r

0

ill

2

)

B
it

LW2

20pc.

20pc.

FW2

- 5/16" Flat Washer

(Y05416-203)

10 [e-mail]

- 5/16" Lock Washer

(Y05416-300)

20pc.

(Y08416-300)

TN2 -

5/16 - T-Nut

1pc.

YP1 -

X Insert Pin

(Y70814-001) (34 PK)

Hardware Identification ( )

8

pc

.

­L

M

o

u

n

t

L

e

f

t

­(

Y

0

0

4

1

9

-

0

0

4

)

Dimensions are approximate and are shown to assist in the identification of
parts for assembly. Actual dimensions may be smaller or larger.

8

pc

.

­L

M

o

u

n

t

Ri

g

h

t

­(

Y

0

0

4

1

9

-

0

0

5

)

9 pc.

- 2 x 3 Trellis Clip

(Y00413-001)

4 pc.

- Beam Hanger

(Y00413-011)

11 [e-mail]

Step 1: Inventory Parts - Read This Before Starting Assembly

STOP STOPSTOP STOP

A. This is the time for you to inventory all your hardware, wood and accessories,

referencing the parts identication sheets. This will assist you with your assembly.

• Each step indicates which bolts and/or screws you will need for assembly, as well as
any at washers, lock washers, t-nuts or lock nuts.

B. If there are any missing or damaged pieces or you need assistance with

assembly please contact the consumer relations department directly. Call us
before going back to the store.

1-888-509-4382

[e-mail]

C. Read the assembly manual completely, paying special attention to ANSI warnings;

notes; and safety/maintenance information on pages 1 - 4.

• Follow the instructions in order.

• This structure is designed to be assembled and installed ideally by two people,
DO NOT attempt to install alone.

• Consider the slope of elevation where you plan to install the structure. Also, check for

gas, telephone, other utilities or sprinkler line locations prior to excavating any holes.

D. Before you discard your cartons ll out the form below.

• The carton I.D. stamp is located on the end of each carton.

• Please retain this information for future reference. You will need this information if you
contact the Consumer Relations Department.

PRODUCT NUMBER: YM11645

CARTON I.D. STAMP: __ __ __ __ __ ___ (Box 1)

CARTON I.D. STAMP: __ __ __ __ __ ___ (Box 2)

CARTON I.D. STAMP: __ __ __ __ __ ___ (Box 3)

12 [e-mail]