12' Octagon Wood Gazebo
DESIGN REQUIREMENTS
1. Governing Code:
Including, not limited to: IBC 2015 (ASCE 7-05)
Risk Category: 1
2. Dead Load: 5 psf
4. Ground Snow Load: 30 psf
5. Wind Load:
Basic Wind Speed (V): 110 mph
Exposure Class: B
Open Building, Unrestricted Flow
191 JALYN DRIVE NEW HOLLAND, PA 17557
THIS DRAWING IS THE PROPERTY OF YARD CRAFT,
ANY REPRODUCTION , ALTERNATION, OR USE OF
THIS DRAWING, WITHOUT THE WRITTEN CONSENT
SHALL NOT BE SCALED TO OBTAIN DIMENSIONS.
REPORTED IN WRITTING BEFORE STARTING WORK.
CONTRACTOR:
PH: 1-
866-210-9273
WWW.YARDCRAFT.COM
OF YARD CRAFT, IS PROHIBITED. DRAWINGS
THE CONTRACTORS/DEALERS, AND BUILDERS
INVOLVED ON THIS PROJECT SHALL VERIFY ALL
DIMENSIONS AND CONDITIONS BEFORE
STARTING WORK. ANY DISCEPANCY SHALL BE
YardCraft
DRAWING TITLE:
Cover Page
PROJECT:
12' Octagon Cedar
Gazebo
COMMENTS:
REVISIONS:
DRAWING NUMBER:
DATE:
BY:
10/19/2017
JR.
DATE:
17-284
PAGE:
SCALE:
BY:
1 of 6
1:48
191 JALYN DRIVE NEW HOLLAND, PA 17557
THIS DRAWING IS THE PROPERTY OF YARD CRAFT,
AND REPRODUCTION , ALTERNATION, OR USE OF
THIS DRAWING, WITHOUT THE WRITTEN CONSENT
SHALL NOT BE SCALED TO OBTAIN DIMENSIONS.
STARTING WORK, AND ANY DISCEPANCY SHALL
CONTRACTOR:
PH: 1-
866-210-9273
WWW.YARDCRAFT.COM
OF YARD CRAFT, IS PROHIBITED. DRAWINGS
THE CONTRACTORS/DEALERS, AND BUILDERS
INVOLVED ON THIS PROJECT SHALL VERIFY ALL
DIMENSIONS AND CONDITIONS BEFORE
BE REPORTED IN WRITTING BEFORE STARTING
WORK.
YardCraft
Framing Elevation
13
126
137
52
"
16
9
"
16
5
"
16
(3) Ply 2x4 cedar post,
(3.375"x4.125"), fasten the 2
outside plies to inner ply w/
#8x2 1/2" screw
144
Elevation
(3) Ply 2x4 cedar post,
(3.375"x4.125"), fasten the 2
outside plies to inner ply w/
#8x2 1/2" screw
1
"
16
(2) 2x4 pressure
treated SYP Floor Joist,
fasten together w/
#8x3" screws
2x4 pressure treated
SYP band Board,
fasten to each floor
joist w/ (2) #8x3"
screws
1x4 Cedar Trim
Board, fasten to
band board w/ (3)
#8x1 5/8" screws
55
133
1
"
8
1
"
16
2x4 pressure treated SYP
floor Joist, fasten at each
end w/ #8x3" screws
DRAWING TITLE:
Elevations
PROJECT:
12' Octagon Cedar
Gazebo
COMMENTS:
REVISIONS:
DRAWING NUMBER:
DATE:
17-284
BY:
Post Layout Plan
Floor Framing Plan
DATE:
BY:
10/19/2017
JR.
PAGE:
SCALE:
2 of 6
1:64
1
144
"
4
F
Detail E
B
3
"
59
4
(2) 2x4 SYP rafters, fasten
together w/ #8x2 1/2" screws,
and fasten to post w/ (1)
3/8"Ø threaded rod at each
post
191 JALYN DRIVE NEW HOLLAND, PA 17557
THIS DRAWING IS THE PROPERTY OF YARD CRAFT,
AND REPRODUCTION , ALTERNATION, OR USE OF
THIS DRAWING, WITHOUT THE WRITTEN CONSENT
SHALL NOT BE SCALED TO OBTAIN DIMENSIONS.
STARTING WORK, AND ANY DISCEPANCY SHALL
CONTRACTOR:
PH: 1-
866-210-9273
WWW.YARDCRAFT.COM
OF YARD CRAFT, IS PROHIBITED. DRAWINGS
THE CONTRACTORS/DEALERS, AND BUILDERS
INVOLVED ON THIS PROJECT SHALL VERIFY ALL
DIMENSIONS AND CONDITIONS BEFORE
BE REPORTED IN WRITTING BEFORE STARTING
WORK.
YardCraft
(4) Ply 2x8 SYP compression ring, 2nd ply
fasten to 1st ply w/ #8x2 1/2" screws, 3rd ply
to 2nd ply w/ #8x3" screws, 4th ply to 3rd ply
w/ #8x3" screws.
DRAWING TITLE:
Roof Framing Plan
PROJECT:
B
F
Roof Framing Plan
2x4 SYP fascia, fasten to 2x4 rafter
at each end w/ #8x3" screws
1x4 Cedar Trim, fasten to 2x4
fascia w/ (3) #8x1 1/2" screws
12' Octagon Cedar
Gazebo
COMMENTS:
REVISIONS:
DRAWING NUMBER:
DATE:
BY:
10/19/2017
JR.
DATE:
17-284
PAGE:
SCALE:
BY:
3 of 6
1:32
123
(4) Ply 2x8 SYP compression ring, 2nd ply
fasten to 1st ply w/ #8x2 1/2" screws, 3rd ply
to 2nd ply w/ #8x3" screws, 4th ply to 3rd ply
144
1
"
4
w/ #8x3" screws, and to each ply of rafter
w/ (1) #8x3" screw from bottom
1x6 SYP tongue & groove
decking, fasten to rafters at
12
5.5
18 ga. Roof Bracket, fasten to ceiling
boards and rafters and band board
below w/ (16) 10d nails
T-Rail consisting of a 2x4 flat and 2x2 on
Detail C
15
"
16
edge, fasten together w/ #8x2 1/2"
screws, post is notched 1/8" to accept 2x4
2x6 cedar brace, fasten to
post and T-rail w/ (2) #8x3"
screws, fasten T-rail to post
w/ (2) #8x3" screws
13
"
79
16
2x4 #1 cedar top rail, fasten to post
w/ #8x3" screws, (2) at each end,
post is notched 1/8" to accept this rail
36"
Detail D
2x3 #1 cedar bottom rail. fasten to
post w/ #8x3" screws, (2) at each end
each end w/ (2) 2" nails
(2) 2x4 SYP rafters, fasten
together w/ #8x2 1/2" screws,
and fasten to post w/ (1)
3/8"Ø threaded rod at each
post
1x4 Cedar Trim Board, fasten to
fascia board w/ (3) #8x1 5/8" screws
2x4 SYP fascia, fasten to 2x4 rafter
at each end w/ #8x3" screws
(3) Ply 2x4 cedar post,
(3.375"x4.125"), fasten the 2
outside plies to inner ply w/
#8x2 1/2" screw
1x3 cedar spindles
191 JALYN DRIVE NEW HOLLAND, PA 17557
THIS DRAWING IS THE PROPERTY OF YARD CRAFT,
AND REPRODUCTION , ALTERNATION, OR USE OF
THIS DRAWING, WITHOUT THE WRITTEN CONSENT
SHALL NOT BE SCALED TO OBTAIN DIMENSIONS.
STARTING WORK, AND ANY DISCEPANCY SHALL
CONTRACTOR:
PH: 1-
866-210-9273
WWW.YARDCRAFT.COM
OF YARD CRAFT, IS PROHIBITED. DRAWINGS
THE CONTRACTORS/DEALERS, AND BUILDERS
INVOLVED ON THIS PROJECT SHALL VERIFY ALL
DIMENSIONS AND CONDITIONS BEFORE
BE REPORTED IN WRITTING BEFORE STARTING
WORK.
YardCraft
DRAWING TITLE:
Cross Section With Floor
PROJECT:
12' Octagon Cedar
Gazebo
5/4x6 cedar decking
CROSS SECTION B-B
With Floor
2x4 pressure treated SYP
floor Joist, fasten at each
end w/ #8x3" screws
COMMENTS:
REVISIONS:
DRAWING NUMBER:
BY:
10/19/2017
JR.
DATE:
DATE:
17-284
PAGE:
SCALE:
BY:
4 of 6
1:32
3
2x4 SYP fascia, fasten to 2x4 rafter
at each end w/ #8x3" screws
1x4 Cedar Trim Board, fasten to
fascia board w/ (3) #8x1 5/8" screws
2"
1
"
4
1
"
2
Detail C
18 ga. Roof Bracket, fasten to ceiling
boards and rafters and band board
below w/ (16) 10d nails
(2) 2x4 SYP rafters, fasten
together w/ #8x2 1/2" screws,
and fasten to post w/ (1)
3/8"Ø threaded rod at each
post
Post is notched to accept 2x4
rafter, outside plies of post to
extend to top of rafters
(3) Ply 2x4 cedar post,
(3.375"x4.125"), fasten the 2
outside plies to inner ply w/
#8x2 1/2" screw
191 JALYN DRIVE NEW HOLLAND, PA 17557
THIS DRAWING IS THE PROPERTY OF YARD CRAFT,
AND REPRODUCTION , ALTERNATION, OR USE OF
THIS DRAWING, WITHOUT THE WRITTEN CONSENT
SHALL NOT BE SCALED TO OBTAIN DIMENSIONS.
STARTING WORK, AND ANY DISCEPANCY SHALL
CONTRACTOR:
PH: 1-
866-210-9273
WWW.YARDCRAFT.COM
OF YARD CRAFT, IS PROHIBITED. DRAWINGS
THE CONTRACTORS/DEALERS, AND BUILDERS
INVOLVED ON THIS PROJECT SHALL VERIFY ALL
DIMENSIONS AND CONDITIONS BEFORE
BE REPORTED IN WRITTING BEFORE STARTING
WORK.
YardCraft
1
"
4
1
1
"
2
Post Bracket Detail
1x4 Cedar Trim
Board, fasten to
band board w/ (3)
#8x1 5/8" screws
Detail D
With Floor
2"x3 1/2"x1 1/2" 18 ga. "L"
bracket, fasten to post w/ (4)
#8x2 1/2" screws, and to floor
w/ (2) #12x4" timberlock
screws
(3) Ply 2x4 cedar post,
(3.375"x4.125"), fasten the 2
outside plies to inner ply w/
#8x2 1/2" screw
2x4 pressure treated SYP
floor Joist, fasten at each
end w/ #8x3" screws
2x4 pressure treated
SYP band Board,
fasten to each floor
joist w/ (2) #8x3"
screws
18 ga. Roof Bracket, fasten to
ceiling boards and rafters and
band board below w/ (16)
10d nails
12"
6"
1x6 SYP tongue & groove
decking, fasten to rafters at
each end w/ (2) 2" nails
1x4 Cedar Trim Board,
fasten to fascia board
w/ (3) #8x1 5/8" screws
Detail E
DRAWING TITLE:
Detail Views
PROJECT:
12' Octagon Cedar
Gazebo
COMMENTS:
REVISIONS:
DRAWING NUMBER:
DATE:
BY:
10/19/2017
JR.
DATE:
17-284
PAGE:
SCALE:
BY:
5 of 6
1:32
119
(4) Ply 2x8 SYP compression ring, 2nd ply
144
18 ga. Roof Bracket, fasten to
ceiling boards and rafters and
band board below w/ (16)
10d nails
12
5.5
1
"
4
fasten to 1st ply w/ #8x2 1/2" screws, 3rd ply
to 2nd ply w/ #8x3" screws, 4th ply to 3rd ply
w/ #8x3" screws, and to each ply of rafter
w/ (1) #8x3" screw from bottom
1x6 SYP tongue & groove
decking, fasten to rafters at
each end w/ (2) 2" nails
(2) 2x4 SYP rafters, fasten
together w/ #8x2 1/2" screws,
and fasten to post w/ (1)
191 JALYN DRIVE NEW HOLLAND, PA 17557
THIS DRAWING IS THE PROPERTY OF YARD CRAFT,
AND REPRODUCTION , ALTERNATION, OR USE OF
THIS DRAWING, WITHOUT THE WRITTEN CONSENT
SHALL NOT BE SCALED TO OBTAIN DIMENSIONS.
STARTING WORK, AND ANY DISCEPANCY SHALL
PH: 1-
866-210-9273
WWW.YARDCRAFT.COM
OF YARD CRAFT, IS PROHIBITED. DRAWINGS
THE CONTRACTORS/DEALERS, AND BUILDERS
INVOLVED ON THIS PROJECT SHALL VERIFY ALL
DIMENSIONS AND CONDITIONS BEFORE
BE REPORTED IN WRITTING BEFORE STARTING
WORK.
3/8"Ø threaded rod at each
15
T-Rail consisting of a 2x4 flat and 2x2 on
5
"
8
edge, fasten together w/ #8x2 1/2"
screws, post is notched 1/8" to accept 2x4
post
1x4 Cedar Trim Board, fasten to
CONTRACTOR:
YardCraft
fascia board w/ (3) #8x1 5/8" screws
5
"
8
13
"
79
16
2x6 cedar brace, fasten to post
and T-rail w/ (2) #8x3" screws, fasten
T-rail to post w/ (2) #8x3" screws
(3) Ply 2x4 cedar post,
(3.375"x4.125"), fasten the 2
outside plies to inner ply w/
#8x2 1/2" screw
DRAWING TITLE:
Cross Section Without Floor
2x4 #1 cedar top rail, fasten to post
w/ #8x3" screws, (2) at each end,
post is notched 1/8" to accept this rail
1x3 cedar spindles
PROJECT:
36"
2x3 #1 cedar bottom rail. fasten to
post w/ #8x3" screws, (2) at each end
(3) Ply 2x4 cedar post,
(3.375"x4.125"), fasten the 2
12' Octagon Cedar
Gazebo
outside plies to inner ply w/
Detail G
#8x2 1/2" screw
COMMENTS:
CROSS SECTION F-F
Without Floor
2"x3 1/2"x1 1/2" 18 ga. "L" bracket, fasten to post
w/ (4) #8x2 1/2" screws, and to Deck or concrete
foundation by others w/ (2) #12x2 1/2" screws
Detail G
Without Floor
REVISIONS:
DRAWING NUMBER:
BY:
10/19/2017
JR.
DATE:
DATE:
17-284
PAGE:
SCALE:
BY:
6 of 6
1:32
Loading...