Yanmar MP Service Manual

4.
lnspect the pump housing
(Figure 5-19, (1,2)).
If the pump housing is worn, replace the complete pump assembly.
5.
lnspect the drive gear assembly
(Figure 5-20, (3)),
ports
(Figure 5-21, (1))
(Figure 5-20, (2)),
(Figure 5-21, (3))
FUEL
(Figure 5-20, (I)),
drive pin
seal
(Figure 5-21, (2))
and O-ring seal areas
for wear. If damaged or worn,
replace the complete pump assembly.
PUMP
rotor
oil
Figure
5-1
9
0003559
Figure
Figure
5-20
5-21
mNMAR.
MP
Series
Service
Manual
FUEL
INJECTION
PUMP
Hydraulic Head
1.
Mark the positions of the fuel inlet
(Figure 5-22, (1))
(Figure 5-22, (2))
The delivery valve has many parts that are
small. Do not drop or lose the check
very valve.
2.
Remove each of the delivery valve housings
valves and gaskets
and return fittings and remove.
Figure
5-22
IMPORTANT
(Figure 5-23).
Note: Be careful not to lose the secondary
check balls during disassembly of the delivery valves.
3.
Disassemble each delivery valve
(Figure 5-24).
Note: Keep and identify all parts in order during
disassembly. Do not mix valve parts. If reused, each valve must be reassembled with the original parts and reinstalled in the original port.
1.
Valve Seat
2.
Return Spring
3.
Secondary Check Ball Spring Seat
4.
Secondary Check Ball
5.
Delivery Valve
6.
Primary Spring
7.
Delivery Valve Housing
Figure
5-23
0001
181
Figure
4.
Remove the distribution shaft plug
(Figure 5-25, (I)),
and O-ring
(Figure 5-25, (2)).
Figure
5-24
GO03552b
5-25
MP
Series
Service
Manual
YANMAR,
IMPORTANT
Do not use magnetized tools, as this may cause fuel pump components to become magnetized and attract metal debris.
5.
Remove the distribution shaft
Figure
(Figure 5-26).
5-26
0001
185
FUEL INJECTION PUMP
7.
Note the position of the coolant fitting
(Figure 5-28, (3)) (Figure 5-28,
and fitting. Remove the thermo-element assembly
(Figure 5-28,
timer piston return spring
(Figure 5-28, (7)),
and seal
(Figure 5-28,
and remove the coolant plug
(I)),
gasket
(Figure 5-28, (5)),
(Figure 5-28, (2))
(4)),
which includes the
timer piston
(Figure 5-28, (6))
gaskets
(Figure 5-28, (8))
(9)).
timer housing
Note: Store parts in clean oil to prevent
oxidation.
6.
Remove the plunger and barrel plug
(Figure 5-27,
and copper seal
(I)),
O-ring
(Figure 5-27, (2))
(Figure 5-27, (3)).
Figure
5-27
Figure
0003551
5-28
YANMAR,
MP
series service
Manual
FUEL INJECTION PUMP
Remove the charge pump fuel outlet strainer plug
(Figure 5-29, (1))
(Figure 5-29, (2)).
and gasket
Do not remove the strainer.
Remove the accumulator plug
(Figure 5-29, (3))
spring and piston
washer
(Figure 5-29,
(Figure 5-29,
(4)),
(5,6)).
0003554
Figure 5-29
Remove the four hydraulic head bolts
(Figure 5-30, (1)).
10.
Remove the hydraulic head assembly and
gasket
(Figure 5-31, (1)).
Figure 5-31
Figure 5-30
0001
193A
11.
Use the spring compressor tool
(Figure 5-33, (2))
(Included in Yanmar Special Tool Kit P/N 458091) to compress the plunger spring
retainer
(Figure 5-32, (1))
(Figure 5-33, (1)).
and remove the spring
MP
Series
Figure 5-32
Service
Manual
YANMAR
FUEL INJECTION PUMP
1.
Spring ~etainer
'
2. Spring Compressor Tool
3.
Hydraulic Head
Figure
5-33
12. Remove the control rack return spring
(Figure 5-34, (1)).
14. Remove the spring retainer control sleeve
(Figure 5-36, (2))
(Figure 5-36, (3)).
Figure
Note: Store all valves
(Figure 5-37)
from hydraulic head assembly in clean oil to prevent oxidation.
(Figure 5-36,
and plunger
5-36
removed
(I)),
00001 2 17
0001214a
Figure
5-34
13. Remove the control rack guide and bolts
(Figure 5-35, (1)).
00001215a
Figure
5-35
Figure
5-37
0001220
i
YANMAR.
MP
series service
Manual
FUEL INJECTION PUMP Distribution Shaft. Camshaft and
Roller Lifter Removal
1.
Remove the distribution shaft coupler
(Figure 5-38, (1)).
0001
Figure 5-38
196
3.
Remove the roller lifter alignment pin
(Figure 5-40, (1)) (Figure 5-40,
4.
Remove the roller lifter Retain the shim
the lifter bore.
and O-ring and the link lifter
(2))
and O-ring.
Figure 5-40
(Figure 5-41, (2)).
(Figure 5-41, (1))
-
located in
2.
Remove the distribution shaft retainer bolts
(Figure 5-39, (1)) (Figure 5-39, (2)).
and retainer
.
Figure 5-39
_...
-_
---i_
Figure 5-41
5-22
MP
~er~es ~ervlce
Manual
YANMAFI,
FUEL INJECTION PUMP
Remove the camshaft bearing retainer bolts and retainer
(MP2
camshaft keyway appropriate timing mark on the body
3
4
-
Cylinder Model Cylinder Model
(Figure 5-42, (1)).
Figure 5-42
3
Cylinder Model Pumps)
(Figure 5-43, (1))
(Figure 5-43, (2)) (Figure 5-43,
Align the
with the
or
(3)).
(MP4 Model Pump) (Figure 5-44, (2)) (Figure 5-44, (1))
Lift the distribution shaft slightly and pull out the camshaft
(Figure 5-45, (2))
damaging the camshaft lobes.
Align the camshaft keyway with the embossed mark on the body.
Figure 5-44
(Figure 5-45,
being careful to avoid
(1))
YANMAR*
Figure 5-43
MP
series service
Figure 5-45
Manual
FUEL INJECTION
9.
Remove the distribution shaft assembly
(Figure 5-46).
PUMP
0001210
FUEL PUMP REASSEMBLY
Distribution Shaft and Camshaft
1.
Invert the pump body and apply assembly grease to the distribution shaft and gears
(Figure 5-47,
pump body.
Note: Check that the distribution shaft rotates
freely after installation.
(1))
before installing it into the
Figure
5-46
Figure
2.
Apply assembly grease to the camshaft lobes, bushing journal and ball bearing.
5-47
0001237
5-24
MP
series service
Manual
YA
NMAR
FUEL
INJECTION
PUMP
3.
With the distribution shaft gear touching the pump body, insert the camshaft into the body. During installation prevent the cam lobes from hitting the distribution shaft gear and the camshaft key from hitting the camshaft bushing.
(Figure 5-48).
Note: 4-cylinder camshafts require special care
during reassembly due to tight tolerances.
4. Install the camshaft bearing retainer and bolts
(Figure 5-49,
(8
-
10
N.m).
-
.
(1))
and tighten to
6
-
7
ft-lb.
Figure
5-48
0001
239
Figure
5-49
VANMAR.
MP
series service
Manual
5-25
FUEL INJECTION PUMP
Gear
Alignment
Note: Verify model of fuel injection pump before proceeding
1.
Rotate the camshaft to the correct angle (aligning keyway to marks) for the model pump being serviced
(Figure
5-50)
and hold in position.
2. Look through the charge pump opening in the case and slightly lift the distribution shaft and rotate to align the distribution shaft gear and camshaft gears marks. Once the marks are aligned, do not raise the distribution shaft too far or the gears will disengage and misalign.
3.
The gears are properly aligned when the gear marks are aligned, the distribution shaft drive lugs are in parallel alignment with the retainer screws and the camshaft keyway is at proper angle from step
4.
While holding the gear alignment, install the distribution shaft retaining plate and tighten screws to
6 - 7
ft-lb.
(8
-
10
N-m).
5.
Verify proper gear alignment by checking gear timing marks for proper alignment.
Distribution Shaft Angle
Camshaft Angle MP2
-
3
Cyl.
Camshaft Angle MP2
-
4
Cyl.
1.
'.
PI
1.
Retaining Plate
0003556A
0001207BB W1207B
3.
Housing Timing Marks
2. Distribution Drive Shaft Lugs 4. Camshaft Key Camshaft Angle MP4
0001 207CC
Figure
5-50
MP
Series
Service
Manual
YANMAR,
FUEL INJECTION PUMP
Roller Lifter
1.
lnstall the link lifter
O-ring.
2.
Install the roller lifter
groove on the side of the lifter aligned with the
lifter alignment pin hole.
(Figure 5-51, (1))
(Figure 5-51, (2))
Figure
5-51
and
with the
0001248A
Plunger and Control Rack
1.
Install the plunger
head assembly.
(Figure 5-53, (1))
Figure
5-53
into the
3.
With roller lifter groove aligned, install the roller
lifter alignment pin
tighten the pin by hand
(Figure 5-52, (1)).
(4
mm hex wrench)
Slowly
while turning camshaft to ensure the lifter
moves freely with pin in position. Torque the pin
to
3
-
4
ft-lb.
(4
-
5
N-m). Lifter must move freely
after pin is torqued.
Figure
5-52
0001249
2.
Install the control sleeve
(Figure 5-55, (2))
aligning the plunger identification marking
(example:
(Figure 5-54, (2))
1.
Upper Lead
2.
Ball Marking
3.
Sub-lead
"W4")
(Figure 5-54, (4))
of the control sleeve.
4.
Identification
Figure
5-54
with the ball
YANMAR.
MP
series service
Manual
FUEL INJECTION PUMP
3. Install the spring retainer
-
--
1.
Spring Retainer
2.
Control Sleeve
--
-
(Figure
3. Plunger
Figure 5-55
5-55,
(1)).
00001217
5.
Installing the slide into the spring retainer
(Figure
5-57,
(I)), (Figure
5-58,
Figure 5-57
(1)).
0000 12338
4.
Install the control rack guide
(Figure
5-56,
into the corresponding positions (hole and pin) on the spring retainer see
Figure
5-57
and
(Figure
Figure
5-56,
5-58.
(1)).
Figure 5-56
(2))
Also
00001 233A
Figure 5-58
Install and tighten the four bolts
(Figure
5-59,
(1))
to
2
-
3 ft-lb. (3
-
4
N-m).
MP
Series Service
Figure 5-59
Manual
YANMAR*
00001215a
FUEL INJECTION
9.
7.
Measure the rack (Figure 5-60,
(4))
movement,
the range of rack motion should be The spring must be able to return the rack from
approximately 14 mm of total travel. the maximum decreased fuel position to the
8. Measure rack backlash, the total backlash should be equal to or less than 0.008 in. (0.2 mm). If the backlash is excessive, replace the rack assembly and control sleeve.
Install the rack return spring (Figure 5-61,
maximum increased fuel position.
Figure 5-61
10. Install the plunger spring (Figure 5-62, (1)) and spring retainer (Figure 5-62,
(2)).
Use the spring compressor tool (Figure 5-63, (2)) (Included in Yanmar Special Tool Kit
PIN
458091) to compress the plunger spring and install the spring retainer.
PUMP
(1)).
1. Control Rack 4. Rack Guide 5. Upper Spring
2.
Control Sleeve Retainer
3.
Rack Auxiliary
6.
Distribution Shaft
Spring Sleeve
Figure 5-60
OKl12128
Figure 5-62
YANMAR,,
MP
Series Service Manual
FUEL
INJECTION
PUMP
0001213
1. Spring Retainer
2.
Spring Compressor Tool
3. Hydraulic Head
Figure
5-631
11. Install the distribution shaft coupler
(Figure 5-64, (1)).
13. Install the original plunger shim(s) (Figure 5-66, (1)) inside the lifter.
Figure
5-66
14. Install the hydraulic head assembly and temporarily tighten the
(6
mm hex) head bolts
evenly in the order as shown (Figure 5-67, (1,
2,
3,4)) until the surfaces of the head and.the
pump body contact each other. Then tighten to torque of
(MP2 - 13 - 16 ft-lb. (18 - 22 N.m)) (MP4 - 21
-
24
ft-lb.
(28
-
32 N-m)) in a diagonal
order.
Figure
12.
Install a new head gasket (Figure 5-65, (1)).
Figure.
5-64
5-65
Figure
0001259
5-67
5-30
MP
series
service
Manual
YANMAR,
FUEL INJECTION PUMP
Plunger (Bottom Clearance) Measurement
The MP fuel pump injection timing is set by adjusting the plunger height. This is accomplished
using shims in the roller lifter body to move the plunger up or down (bottom clearance) from the
camshaft base circle.
Note: Do not use the ball tip on the dial
indicator when measuring, use the dial indicator extension alone.
1. Mount the dial indicator (from Yanmar Special Tool Kit PIN 458091) in the adapter and thread into barrel.
2.
Position the camshaft with the roller lifter at the
bottom of the cam profile.
3. Remove the dial indicator and adapter and zero
5-68,
the dial indicator (Figure specified spacer (Figure size spacer can be found in the calibration data sheet (bottom clearance [mm]) for each pump number.
(1)) using the
5-68,
(2)).
The correct
5. Using shims from the shim kit in the Yanmar Parts Catalog (MP2
-
PIN 158553-51250),
(MP4 - PIN 129906-51 400), increase or
5-69,
decrease the shim pack (Figure
(3))
the roller lifter bore to obtain the zero mark
(+
0.03 mm) on the dial indicator.
in
0001314AA
1. Dial Indicator 3. Flat Surface
2. Plunger Spacer
Figure
5-68
4. Reinstall the dial indicator (Figure into the barrel (Figure
5-69,
(1)) and record the
measurement.
5-69,
(4))
1. Barrel
U
4. Dial Indicator
0001315A
2. Plunger 5. Plunger
3.
Shim(s) Adjustment
Dimension
Figure
5-69
"An
YANMAR,
MP
series
service
Manual
FUEL INJECTION PUMP Hydraulic Head and Valve(s)
Reassembly
1.
Set the camshaft to the correct angle as used during the gear alignment.
2. Lubricate the distribution shaft.
3.
Align the drive lugs on the bottom of the distribution shaft and install to engage the distribution shaft coupler.
Note: The flat on the distribution shaft
(Figure 5-70, (1))
engine side of the pump (or away from
the accumulator piston side).
4. Install the distribution shaft plug
(Figure 5-70, (3))
and tighten to
11
should face toward the
and O-ring
ft-lb. (15 N-m).
(Figure 5-70,
(2))
Install new delivery valve seat seal(s)
(Figure 5-71, (1)).
Figure 5-71
Assemble and install each delivery valve
(Figure
housing to
5-72).Tighten each delivery valve
30
-
33
ft-lb. (40 - 45 N.m).
M01274
Figure 5-70
Note: Some old style hydraulic heads have a
distribution shaft plug with a flat bottom. The replacement will require a new plug to allow clearance for the taller distribution shaft. The parts catalog lists the new plug with a machined recess on the bottom.
5-32
1.
Valve Seat
2.
Return Spring
3.
Secondary Check Ball Spring Seat
4. Secondary Check Ball
5.
Delivery Valve
6.
Primary Spring
7.
Delivery Valve Housing
Figure 5-72
7.
Install the charge pump fuel outlet strainer gasket
(Figure 5-73, (1))
16
(Figure 5-73,
-
21 ft-lb. (25
MP
series service
(2))
and tighten the plug
to
-
29
N.m).
Manual
VANMAR.
FUEL
INJECTION
PUMP
8.
lnstall the accumulator piston
and check that it moves freely. lnstall the spring
(Figure 5-73, (5)),
tighten the plug to
37
-
4lft-lb. (50 - 55 N.m).
9.
lnstall a new timer housing seal
(Figure 5-74,
seal
(Figure 5-73, (3))
Figure 5-73
(1))
(Figure 5-73, (6))
(Figure 5-73,
(4))
and
10. lnstall a new seal head. lnstall new O-rings
the timer housing the timer housing tightening to
30 - 33
11. lnstall the timer spring piston
ft-lb.
(Figure 5-75, (5))
(Figure 5-75,
(Figure 5-75, (7))
(40
-
45 N-m).
(9))
into the
(Figure 5-75,
and install
(Figure 5-75, (6))
into the housing.
(8))
and
on
Figure 5-74
Figure 5-75
0001279
YANMARe
MP
Series
Service
Manual
5-33
FUEL INJECTION PUMP
12. Install a new O-ring thermo-element to 22 - 26 ft-lb. (30 - 35
(Figure 5-76, (2))
(Figure 5-76, (1))
N-m).
Do not over-torque.
Figure 5-76
13. lnstall the engine coolant fitting
(Figure 5-75, (3))
and seals in their original
position.
on the
and tighten
Charge Pump
Note: If charge pump was disassembled for
inspection, clean all parts thoroughly before reassembly. If any part is suspected of damage or failure, replace
the complete pump assembly.
1. lnstall and align pump gears into pump housing.
2. lnstall the new pump housing O-ring
(Figure 5-78, (2))
into groove and assembly pump housings. Tighten the two pump housing screws
-
7
ft-lb. (8 - 10 N-m).
6
(Figure 5-78,
(Figure 5-78, (1))
(5
mm hex)
(3))
to
14. lnstall the coolant plug
(Figure 5-75, (1))
tighten to 16 - 18 ft-lb. (22 - 25 N-m). Do not over-torque.
15. lnstall the fuel return inlet fittings
(Figure 5-77, (I)),
(Figure 5-77, (2))
seals and plugs
to positions marked in disassembly.
Figure. 5-77
and
and
0003559A
Figure 5-78
lnstall new charge pump housing O-rings
(Figure 5-79, (1)).
5-34
MP
Series
Figure 5-79
Service
Manual
YANMAR,
4. Install the charge pump tighten the four mount screws to
6
-
7
ft-lb. (8
-
10
(Figure 5-80, (1))
N.m).
Figure
5-80
(Figure 5-80,
Governor Installation
1.
Install the governor weight assembly and nut
(Figure 5-81, (1))
camshaft
.
to the fuel injection pump
and
(2))
FUEL
2.
Attach a stop to the camshaft. Tighten the governor weight nut 58
-
62
ft-lb.
(79
-
sleeve.
Note: Be careful not to bend or damage the
governor housing gasket.
3.
Align and install a new governor housing gasket
(Figure 5-83,
(1)).
INJECTION
(Figure 5-82, (1))
84 N-m). Install the governor
Figure
5-82
to
0001251a
PUMP
YANMAR,
Figure
MP
Series
5-81
Service
Manual
Figure
5-83
000
13Wa
5-35
FUEL INJECTION
4.
Turn the link lifter plate counterclockwise to the
PUMP
6 o'clock position and install the governor assembly and link into the pump body (Figure 5-84).
00013Ma
Figure 5-84
Note: Do not force the link during installation,
as damage can occur to the link and control rack pin.
Note: Figure 5-85 illustrates the governor link
connection to the control rack. The actual connection is blind, therefore this
illustration is used to assist during
assembly.
5. While installing the governor assembly, slide the link lifter as shown (Figure
5-85,4), to allow the link to slide in to align with the control rack pin.
1.
Control Rack
4.
During Assembly
2. Governor Link 5. During Operation
3. Link Lifter
Figure 5-85
6. Install two governor housing bolts by hand to hold the governor in place.
7.
While pushing the governor lever assembly to the full stop position through the stop solenoid opening, rotate the link lifter clockwise to the
12 o'clock position.
8.
Verify the link installation by watching plunger rotation from the top of the hydraulic head. The plunger should rotate in both directions while moving the control rack in and out.
9.
Install a new copper seal (Figure 5-86, plunger and barrel plug (Figure 5-86, O-ring (Figure 5-86,
-
(MP2
22 - 26 ft-lb. (30 - 35 N.m))
(2)).
Tighten to
(3)),
(1))
and
(MP4 - 33 - 37 ft-lb. (45 - 50 N.m)).
5-36
MP
Series Service
Figure 5-86
Manual
YANmAR
FUEL
PUMP
10. Tighten the link lifter retainer bolt
(Figure
5-87,
(1))
to
6-
7
ft-lb (8 - 10 N.m). stop solenoid and install the stop solenoid to
OD01 304a
Figure 5-87
11. Install the governor housing screws and tighten to
6
-
7
ft-lb (8 - 10 N-m)
(Figure
5-88).
12. Install a new O-ring
(Figure
5-89,
(1))
the governor housing. Tighten the solenoid
6
-
7
ft-lb
(8
-
10
bolts to
N-m).
Figure 5-89
13.
Pre-set the adjustment of the angleich assembly, by loosing the angleich lock nut
(Figure
5-90,
(1)).
to the
0001
306a
.
.
YANMAR.
Figure 5-88
MP
series service
Manual
0001305a
0001
306C
Figure
5-90
14. Turn the angleich adjustment screw in until it contacts the governor lever and then back out one-quarter
(114) turn.
15. Tighten the angleich lock nut.
5-37
I
FUEL INJECTION PUMP
16.
Install a new governor housing cover gasket
(Figure 5-91).
Figure 5-91
17.
Install the governor housing cover to the case
(Figure 5-92).
cover bolts to
Tighten the governor housing
6
-
7
ft-lb
(8
-
10
N-m).
0001307a
5-38
Figure 5-92
0001 308a
MP
series service
Manual
YANMAR*
Section
6
ADJUSTMENT
Page
Introduction Setup and Inspection Adjustment
Component Identification
High Rated Fuel Delivery
Torque Fuel Delivery
Reverse Angleich Spring Adjustment Low
Start Fuel Delivery
Ultra-Low Speed Delivery Stop Fuel Delivery
Tamper-Proof Cap Installation
Fuel Pump Timing Index Stamping Identification
................................................................................
.......................................................................
......................................................................................
...........................................................
Idle Fuel Delivery
..............................................................
................................................................
.................................................................
........................................
Idle Fuel Delivery
...............................................................
.....................................................................
........................................................
.....................................................................
...................................................
......................
6-3 6-3 6-4
6-4 6-4 6-4 6-5 6-5 6-6 6-6 6-6 6-6 6-7 6-7
YANMAR
.
MP
Series
Service
Manual
ADJUSTMENT
This Page Intentionally Left Blank
MP Series Service
Manual
YANMAR.
ADJUSTMENT

INTRODUCTION

3. Mount the fuel injection pump
(Figure
6-2)
on
the pump tester platform.
This section of the Service
Manual
describes the adjustment procedures necessary to setup and adjust the fuel injection pump and governor.
The fuel injection pump delivery must be calibrated, whenever the pump is disassembled.
A
fuel pump test bench
make the necessary adjustments.
(Figure 6-1)
is required to
Figure
6-2
4. Remove the oil fill plug on the top of the
I
I
SETUP AND INSPECTION
1.
Verify adjusting nozzle assembly and injection
governor case. Fill with about 6.75
oz (200 cc) of pump oil or
(Figure 6-3,
(1))
the pump
engine oil.
I
starting pressure.
Figure
2.
Inspect the high pressure injection line.
Inner diameter
x
Outer diameter
Minimum bending radius
length
6-1
0.24 (6.0 x 600 mm)
0.08
in.
(2.0 mm)
x
23.62
in.
0.98
(25
mm)
in.
Figure
5.
Securely tighten all fuel lines to the fuel pump
6-3
and tester.
6. Set the oil feed pressure
(1
2.8-4.3 psi
9.6 - 29.4 kPa, 0.2 - 0.3 kgf/cm2),
temperature at 40 * 2°C
Figure
(Figure 6-4)
(1
04 3.6"F).
6-4
at
7. Operate the pump tester to purge the fuel lines of all air.
YANMAR
MP
series service
Manual
ADJUSTMENT
ADJUSTMENT
The adjustment of fuel delivery requires correct specifications. Before performing any of the adjustments in this section, obtain the correct calibration data sheet for the fuel injection pump
being tested. Contact your Yanmar Fuel Injection Equipment Central Distributor to obtain the data
sheet. Adjustments must be performed in the following
order when adjusting the governor:
1.
High ldle Fuel Delivery
2.

Rated Fuel Delivery

3.
Torque Fuel Delivery
4. Reverse Angleich Spring Adjustment
5.
Low ldle Fuel Delivery
6.
Starting Fuel Delivery
7.
Stop Fuel Delivery
8.
Re-check Rated Fuel Delivery
9.
Tamper-Proof Cap Installation
High ldle Fuel Delivery
1. Set the fuel pump speed at the high idle speed specified.
2.
Set the control lever idle position while turning the high idle speed limit bolt injection amount.
3.
Tighten the lock nut after completing the adjustment to lock the high idle speed limit bolt from turning.
(See Calibration Data Sheet).
(Figure 6-5, (6)
(Figure 6-5,
(3))
to obtain the specified
(See Calibration Data Sheet).
to the high
Rated Fuel Delivery
The MP2 pump has a rated fuel limiter adjustment assembly
1. Remove the tamper-proof cap and screw in the fuel limiter assembly contacts the governor tension lever and then
back off one-quarter
Figure 6-6
as standard equipment.
(Figure 6-6, (1))
(114) turn.
until it
Component Identification
1. Rated Fuel Limiter Adjustment Assembly
2. Starting Fuel Adjustment Assembly
3.
High ldle Speed Limit Bolt
4. Reverse Angleich Adjustment Assembly
5.
Low ldle Speed Limit Bolt
6.
Control Lever
Figure
6-5
Figure
2.
Set the pump speed at the rated speed
Calibration Data Sheet)
lever until it contacts the high idle speed limit
(Figure
bolt
3.
Adjust the rated injection amount by turning the fuel limiter assembly to obtain the correct specification,
Calibration Data Sheet).
6-5,
(3)).
6-6
and move the control
(Figure 6-6, (1))
(See
in or out
0003465m
(see
MP
Series Service
Manual
ADJUSTMENT

Torque Fuel Delivery

Torque fuel delivery adjustment requires adjustment of the fuel limiter torque spring
(Figure
1.
If the fuel limiter assembly has a torque spring:
6-7,
(3))
or angleich, when applicable.
Set the pump speed at the torque rise speed
(See Calibration Data Sheet)
and move the
control lever until it contacts the high idle speed
limit bolt.
Screw in the fuel limiter torque spring adjustment screw the specified injection amount
Data Sheet)
(Figure
6-7,
(4))
(See Calibration
and fasten the lock nut.
to obtain

Reverse Angleich Spring Adjustment

Note:) Do not thread past the reverse angleich
lever or the reverse angleich lever will move in a direction of fuel reduction.
1.
With the pump stopped, remove the governor housing rear cover
(Figure
the angleich assembly
contact is just made with the reverse angleich lever
(Figure
6-9,
(4)).
2. Shift the control lever to the high idle position. Set the fuel pump speed to the specified torque rise
RPM
number.
Sheet).
(See Calibration Data
6-9,
(Figure
(1))
6-8,
and adjust
(1))
until
0003465p
Figure
6-7
If the fuel limiter assembly does not have torque
spring:
See
Reverse Angleich Spring Adjustment
this page.
on
Figure
3.
Set the angleich assembly to the specified injection quantity.
(See Calibration Data Sheet).
4. Tighten the lock nut
-
29.4
N-m
24.5
(2.5
6-8
(Figure
-
3.0
kgf.m).
6-8,
(2))
00034651
to
YANMAR,
MP
series service
Manual
ADJUSTMENT
5.
Recheck the rated fuel delivery.

Start Fuel Delivery

1.
Set the pump speed at the specified starting injection RPM and set the control lever at the high idle position.
2.
Turn the starting fuel adjustment bolt
(Figure 6-1 1, (1))
injection amount.
3.
Tighten the locknut install the hex cap.
(see Calibration Data Sheet),
to obtain the specified
(See Calibration Data Sheet)
(Figure 6-1 1, (2))
and
(3)
1.
Governor Rear
3.
Governor Tension
Cover Lever
2.
Reverse Angleich
4.
Reverse Angleich
Spring Lever
Figure
6-9
Low Idle Fuel Delivery
1.
Set the pump speed at the low idle pump speed
(see Calibration Data Sheet)
lever
(Figure 6-10, (1))
2.
Turn the low idle speed limit bolt
(Figure 6-10, (2)
delivery amount.
3.
Tighten the lock nut.
to achieve the correct idling
(See Calibration Data Sheet)
with the control
in the idle position.
0003465h
000
1324
Figure
6-1 1

Ultra-Low Speed Delivery

1.
Set the pump speed at
50
RPM and check the ultra-low speed setting injection volume specification.
(See Calibration Data Sheet)
Note: The Ultra Low Speed Test checks the
condition of the plunger and barrel.
Delivery below specifications indicates
excessive leakage.

Stop Fuel Delivery

Set the control lever at the high idle position.
1.
Set the pump speed at specified high idle speed
Sheet)
and check that the (governor cut out)
injection amount reduces to zero.
Calibration Data Sheet)
2.
Set the pump at the rated speed and turn off the stop solenoid and check that the injection amount reduces to zero.
50
RPM higher than the
(see Calibration Data
(See
Figure
6-1
0
MP
Series
Service
Manual
YANMAR.
ADJUSTMENT
Note: There are a few turbo charged engines
that incorporate a boost compensator on the governor assembly. Additional calibration data, procedures and adjustments can be found in the calibration data field of the Yanmar
Distributor Web Site.

Tamper-Proof Cap Installation

1. Install a new tab washer tamper-proof cap
(Figure 6-1
limiter assembly.
2.
Install a new tamper-proof cap
(Figure 6-13, (1))
on the high idle adjustment
assembly.
(Figure 6-1 2, (1))
2,
(2))
on the fuel
and
Fuel Pump Timing lndex Stamping Identification
The timing index numbers stamped on the original fuel pump hydraulic head are needed for the engine
technician to set fuel injection timing. Replacement hydraulic heads do not have the
necessary timing index numbers stamped on the engine side boss like the original fuel pumps. The timing index numbers are needed to properly set injection timing when reinstalling the fuel injection
pump. Upon completion of fuel pump repairs when the
is
hydraulic head number must be manually stamped
(Figure 6-14, (1))
of the hydraulic head.
replaced the correct timing index
onto the boss on the engine side
Figure
Figure
6-12
6-13
0003465q
.
-
Figure
6-14
T
0004666
The correct timing index number can be found on the Yanmar Distributor Web Site under the "F.I.E." heading or under the document search function.
Use category F.I.E. to locate the timing lndex Information for replacement of the MP Fuel Injection Pump. ISD-05-001, Page
4.
,
YANMAR.
MP
Series
Service
Manual
ADJUSTMENT
This
Page Intentionally Left Blank
MP
Series Service
Manual
YANMAR*
Section
7
FUEL INJECTION
NOZZLE
Page
Introduction Specifications Nozzle Body Identification Number Special Torque Chart Special Service Tools Measuring Instruments
Fuel Injection Nozzle 7-5
Operation Disassembly Cleaning Inspection Reassembly Opening Pressure Adjustment Injection Test
......................................................................................
.................................................................................
.................................................
..................................................................
......................................................................
....................................................................
.......................................................................
...................................................................................
..............................................................................
..................................................................................
..................................................................................
...............................................................................
...................................................
............................................................................
7-2 7-2 7-3 7-4 7-4 7-4
7-5 7-6 7-7 7-7 7-8 7-8 7-8
FUEL INJECTION NOZZLE

INTRODUCTION

This section of the operation and procedures necessary to disassemble and reassemble the fuel injection nozzles.
Yar~mar MP fuel injection pumps are designed for use on TNV
(Dl) Direct lnjection engines, equipped with hole type nozzles. injection pump equipped engines is provided in the following chart.
Yanmar Engines equipped
Service
Manual
A
list of Yanmar MP fuel
Injection Pumps
3TNV82A
describes the
with
MP Fuel

SPECIFICATIONS

All TNV fuel injectors have a three character
identification mark
(Figure
character starts with
"V"
Figure
or
7-1,
"W.
7-1
(1)).
The first
00041
05
*
Fuel injector identification is critical as each engine has a unique fuel injection pressure. The fuel nozzle is specifically matched to the fuel injector by engine model and engine speed.
Note: Fuel injection pressure of a new fuel injector
is reduced approximately 72.5 psi (0.5
MPa;
5.0 kgf/cm2) after about 5 hours of operation
due to the initial break in of the spring. When adjusting a new fuel injector or after it
has been disassembled for service, adjust
the fuel injector
72.5 psi (0.5
MPa; 5.0 kgf/cm2) higher than
the above standard.
MP
Series Service
Manual
YANMAR*

NOZZLE BODY IDENTIFICATION NUMBER

FUEL INJECTION NOZZLE
The type of nozzle can be determined from the identification number outside of the nozzle body.
0001328
Y DLL A
-
Figure
150
P
7-1
244JO
Design Code Nozzle Size
Spray Angle Mounting Angle of Nozzle on Cylinder Head Code
"A:
No Code: Not At Angle
Type (DLL: Semi-Long Type) YANMAR
(P
Size, S Size)
At Angle
(Figure
7-1, (1))
inscribed on the
YANMAR,
MP
series service
Manual
FUEL INJECTION NOZZLE

SPECIAL TORQUE CHART

Component
Injector Nozzle Case Nut
I
I

SPECIAL SERVICE TOOLS

No.
Fuel Nozzle Mount Plate
1.
Yanmar Part No. 158090-51 700
Ultra-Sonic Parts Cleaner
2.
(Locally Available)
Tool Name
I
Tightening Torque
(39
-
44
N-m;
4-
5 kgf.m)
Application
For holding and protecting fuel nozzle when servicing
For cleaning parts
Lubricating Oil Application
I
(Thread Portion and Seat Surface)
Not Applied
Illustration
@
I
0001340
0004195
Note: Tools not having Yanmar part numbers must be acquired locally.

MEASURING INSTRUMENTS

No.
For observing injection spray pattern of fuel
1.
Fuel Injector Tester (Locally Available)
Note: Tools not having Yanmar part numbers must be acquired locally.
injection nozzle and measuring injection pressure
Application
Illustration Instrument Name
MP
Series Service
Manual
'YANmAR.
FUEL INJECTION NOZZLE

Operation

High pressure fuel from the fuel injection pump
flows through the high pressure pipe into the oil
passage in the nozzle housing and enters the nozzle body reservoir.
When the fuel reaches the specified pressure, it pushes open the nozzle valve (held down by spring pressure) and is injected into the combustion chamber at high pressure. lnjection nozzle opening pressure is adjusted using shims to increase or decrease the spring pressure on the nozzle valve. (See Opening Pressure
Adjustment on page
7-8)
FUEL
INJECTION NOZZLE
As fuel passes through the nozzle, it mix uniformly with the air in the combustion chamber. How well the fuel is mixed with high temperature air directly affects combustion efficiency, engine performance and fuel economy.
Note: Fuel injection nozzles must be kept in top
condition to maintain performance and operating efficiency.
The nozzle valve is automatically closed by the
nozzle spring pressure at the end of the fuel injection pump stroke.
Unused fuel between the nozzle valve and nozzle
body flows from the hole above the nozzle spring through the fuel return fitting and back into the fuel tank.
is
atomized to
1.
Fuel Return Fitting
2.
Nozzle Housing
3.
Nozzle Spring (Non-serviceable)
4.
5.
Figure
Nozzle Spring Seat Fllter
7-2
YAMMAR.
MP
series
service
Manual
1.
Reservoir Port
2.
Nozzle Valve
3.
Fuel Reservoir
4.
5.
6.
Figure
Nozzle Body Injection Port
Spray Angle
7-3
FUEL INJECTION NOZZLE Disassembly
Note: Keep all parts in order by cylinder during
disassembly and reinstall all small parts to their mating part as the components as components are matched.
1. Mount the hole type injection nozzle into the YANMAR special fuel nozzle mount plate
158090-51 700
(Figure
7-4,
(2).
Carefully
mount the holder and nozzle in to a vise
(Figure
7-4,
(3)
to ensure the high pressure
mounting threads are not damaged.
2.
Use a socket wrench
(Figure
7-4,
remove the nozzle nut.
(1))
PIN
to
0001330
Figure
3.
Remove all nozzle components including the
7-4
spring seat and shims.
0002093D
Fuel Return Passage Injector Body
Pressure Adjusting Shims Spring Spring Seat Valve Stop Spacer
Nozzle Valve
Nozzle Body
Nozzle Case Nut
Figure
7-5
MP
Series Service
Manual
YANMAR.
FUEL INJECTION NOZZLE
I
l
I

Cleaning

Note: Before inspecting or assembling, all
components must be washed with clean diesel fuel or standard cleaning solution and completely clean and free of contaminants.
1. Clean carbon from outside of nozzle body using a brass brush.
2.
Clean nozzle opening with small length of
deburred steel 0.0055 in. (0.14 mm) wire
(Figure
3.
Clean nozzle seat with cleaning spray.
Note: An ultra sonic cleaner can be used to
7-6,
(1)).
0001331
Figure
effectively clean the injector body and
inner components after loose material is removed.
7-6
0001
332A
Figure
4.
lnspect the nozzle valve stop for scratches and/or wear at the sealing surfaces on both sides. Check for abnormal wear at stop plate center hole where it makes contact with the
nozzle
(Figure
7-8, (I)), replace if worn.
7-7

Inspection

1. lnspect oil seal surfaces for abnormal scratches or wear, replace as necessary.
2.
lnspect nozzle body for scratches and wear on nozzle body and tip. Replace the nozzle if the nozzle sliding surface or seat are scratched or
abnormally worn.
3.
Rotate and slide the nozzle to check for smooth movement
assembly if the nozzle does not slide smoothly.
(Figure
7-8), replace the nozzle
0001333b
Figure
5. lnspect the nozzle spring, replace it if deformed, or the surface is scratched or rusted.
Figure
6.
lnspect the nozzle oil sealing surface for scratches excessive.
and/or wear, replace it if wear is
7-8
0001530
7-9
YANM'R.
MP
Series Service
Manual
FUEL
INJECTION NOZZLE

Reassembly

The fuel injection nozzle is assembled in the
reverse order of disassembly.
1. Insert the adjusting shims, spring and spring seat in the nozzle holder, mount the nozzle valve stop plate with the pin, insert the nozzle assembly and tighten the nozzle case nut.
2. Use the nozzle holder when tightening the case nut to 28.8
-
32.5 ft-lb (39 - 44 N-m, 4 - 5 kgf.m).

Opening Pressure Adjustment

Mount the fuel injection nozzle on the nozzle tester
(Figure 7-10, (1))
injection opening pressure. If it is not at specified pressure, add or remove adjusting shims to increase or decrease the pressure, see
Specifications
pressures. Note: Adjusting by 0.004 in (0.1 mm) results in
a change in the injection opening pressure of about 290 psi (2
20 kgf/cm2)
and use the handle to measure
on
page
7-2
for fuel injector opening
MPa,

Injection Test

After adjusting the nozzle to the specified opening pressure, check the fuel spray condition and make sure the nozzle does not leak.
1. Check the injection spray condition, by operating the nozzle tester lever once or twice per second to check for abnormal injection.
Correct
Spray from each nozzle hole is uniform. Spray is fully atomized (no streams of fuel). Start and stop of injection is "sharp" (a clean chatter sound should be heard).
Poor
-
Figure
7-1
0
COO1
335
0001337A
Excessive difference in spray angle. lncomplete atomization Causes - lncomplete opening/closing of injection nozzle.
Figure
2.
Check that the nozzle tip is not leaking after two
7-1
1
or three injections, then gradually increase the pressure up to 200 psi (1.38
MPa;
14.06 kg/cm2). Maintain the pressure for 5
seconds and make sure that no oil is dripping
from the opening pass the nozzle.
MP
Series Service
Manual
YANMAIP.
3.
Replace the nozzle assembly after all checks above if:
Leakage is evident.
Spray angle is incorrect. Atomization of fuel is incomplete. Opening and closing of nozzle is incomplete.
FUEL INJECTION NOZZLE
WANMAR.
MP
Series
Service
Manual
7-9
FUEL INJECTION NOZZLE
This Page Intentionally Left Blank
MP
Series Service
Manual
VANMAR,
Section
8
TROUBLESHOOTING
Page
Introduction
Troubleshooting
Preliminary Checks
Fuel System Troubleshooting Chart
......................................................................................
...............................................................................
....................................................................
................................................
8-2 8-2
8-2
8-3
YAMMAR.
MP
Pump
Service
Manual

TROUBLESHOOTING

INTRODUCTION

This section of the the diagnosis of the fuel injection pump and fuel system problems.
Service
Manual
includes troubleshooting procedures and troubleshooting charts used in
TROUBLESHOOTING
Troubleshooting a fuel system related problem involves:
Identifying the problem accurately. Duplicating the problem. Correctly identifying the cause of the problem. Correcting the problem.
Eliminating the cause of the damage.
Repairing the damage. Verify corrections made have corrected the initial problem.
Preliminary
To quickly and accurately troubleshoot fuel system problems, the following preliminary checks should be performed before the fuel injection pump is removed. When possible provide troubleshooting assistance to the customer, before the fuel injection pump is removed. This will prevent unnecessary costs that can result from an incorrect diagnosis.
Checks
If the pump is removed prematurely, the initial cause of the problem may never be known.
Check the mechanical condition of the engine. Check the condition of the fuel type and quality, fuel flow, and fuel pressure throughout the fuel system. Check for restrictions and leaks throughout the fuel system. Verify fuel injection timing is within specifications. Verify fuel nozzle operation and nozzle spray condition.

Fuel Injection Pump Repair

If the fuel injection pump is found to be faulty, remove it from the engine for repair.
It is very important that the root cause of the failure is eliminated before installing and I or repairing the fuel injection pump.
MP Pump
Service
Manual
Loading...