Page 1
ML115VS-49-1B
CLINTON SERVICE GUIDE
MODEL 115VS-FOTA-KS
FOR
YAMATO FD-62
DRILLING INSTRUCTIONS
CHAIN CUTTER MODEL 115VS FOTA
TAP GUIDE HOLES
(LARGE HOLES)
SHOULDER SCREW
WASHER & NUT
1. PLACE THE DRILL JIG ON THE MACHINE AS SHOWN.
2. ALIGN THE TOP OF THE DRILL JIG WITH THE TOP OF THE
MACHINE BED.
3.TIGHTEN THE LOCKNUT ON END OF SHOULDER SCREW.
4. DRILL (2) TWO HOLES MARKED "A" WITH #29 DRILL
(30-2130-29) SUPPLIED.
5. LOOSEN THE LOCKNUT AND REALIGN THE JIG SO THE
TAPPING GUIDE HOLES WILL ALIGN WITH THE DRILLED HOLES.
6. TAP THE HOLES WITH AN 8-32 TAP (30-1266-01) USING THE TAP GUIDE
HOLES TO GUIDE THE TAP STRAIGHT.
7. REMOVE THE DRILL JIG.
80-0245-01
DRILL JIG
Page 2
INSTALLATION INSTRUCTIONS
ML115VS-49-2A
FILTER, OILER, REGULATOR & GAUGE ASSEMÂBLY
80-0181-01
80-0181-10
02-2756-01
HOUSING
SWITCH ASSEMBLY
11-0429-03
30-0570-01
CLAMP
33-1506-01
HEX NUT
02-2757-01
COVER
33-0106-04
SCREW
33-0106-06
SCREW
33-1906-01
INT. LOCK WASHER
11-0341-01
SWITCH ASS'Y.
MOVABLE BLADE
NOTES:
1. ASSEMBLE MOVABLE BLADE
01-9448-01 WITH SCREWS
(2) 33-3106-04 AND LOCK
WASHERS (2) 33-1806-01.
2. DO NOT TIGHTEN MOVABLE
BLADE SCREWS AT THIS
TIME.
REFER TO ALIGNMENT
ADJUSTMENT.
33-3106-04
SCREW
33-1806-01
LOCK WASHER
01-9448-01
MOVABLE BLADE
INS-570-3D
INS-2297
STATIONARY BLADE
02-2752-01
BLADE SUPPORT
02-0501-01
GUARD
33-3108-04
SCREW
33-1808-01
LOCK WASHER
NOTE:
ASSEMBLE STATIONARY
BLADE AS SHOWN
INS-2396
33-3108-08
SCREW
02-2754-01
MOUNTING PLATE
33-1808-01
LOCK WASHER
33-3108-12
SCREW
01-9447-01
STATIONARY BLADE
INS-2390
Page 3
ADJUSTMENTS
ML115VS-49-3A
WARNING!!
RADIAL
33-3108-08
SCREW
01-3051-01
SCREW
33-3106-08
ADJUSTING SCREWS
NOTES:
1. LOOSEN SCREW 01-3051-01
AND 33-3108-08 AND ROTATE
ASSEMBLY FOR PROPER
ENGAGEMENT.
2. LOOSEN SCREWS 33-3106-08
AND ADJUST MOVABLE BLADE
AGAINST STATIONARY BLADE
AND LOCK IN PLACE.
TO PREVENT SERIOUS INJURY, DISCONNECT AIR
SUPPLY BEFORE MAKING ANY ADJUSTMENTS.
ALIGNMENT
02-0034-01
ADJUSTING
SCREW
33-3106-04
SCREW
30-2489-01
SET SCREW
CHECK ALIGNMENT
BETWEEN BLADES
AND ADJUST FOR
1/32" OVERLAP
NOTE:
LOOSEN SET SCREW 30-2489-01
AND ADJUST SCREW 02-0034-01
COUNTER-CLOCKWISE FOR
MORE CUTTING EDGE
ENGAGEMENT.
AIR CIRCUIT DIAGRAM
ML115VS-9E
4 WAY AIR VALVE, KNEE OPERATED
80-0185-01
INS-619-1A
Page 4
Loading...