Instruction Manual
Rei Beauté
Table of Contents
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Use in Foreign Countries . . . . . . . . . . . . . . . . . . . . . . . 7
Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Before Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Treatment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
How to Use each Treatment Mode . . . . . . . . . . . . . . . 13
After Treatment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Frequently Asked Questions (FAQ) . . . . . . . . . . . . . . 23
After Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Before using this product, please read these instructions
carefully.
Refer to the Safety Precautions section for important information.
Keep this Instruction Manual for future reference.
Please read all instructions carefully for safe and proper use.
Safety Precautions
Use only as directed.
Immediately discontinue use if any malfunction or unusual
reaction to treatment occurs.
Precautions listed in the instruction manual are very important.
For your safety, please follow them carefully.
Precautions are classified as WARNING or CAUTION in order to
clearly specify the level of danger and possible injury or damage
that may occur if the device is misused.
Safety Precautions
WARNING
CAUTION
This symbol shows you what you must NOT do.
This symbol shows you what you must do.
This symbol shows you what you must be careful with.
Improper use of this device may pose a risk of
death or serious injury.
Improper use of this device may result in fire,
injury, or property damage.
WARNING
Do not use near children.
The intense light may cause
serious eye injury.
Do not block the vents.
Blocking the vents may
overheat the unit and cause
smoke or fire.
Do not touch the filter right
after flash emission.
The filter will get very hot after
flash emission. Touching the
filter may cause burns.
Do not emit the flash directly
in or over eyes.
Direct exposure may cause
serious eye injury.
WARNING
Do not use under any of the following conditions as this may
cause malfunction of medical devices:
Do not use in conjunction with any medical electronic equipment
such as a pacemaker, oxygenator, electrocardiograph, etc.
Consult a doctor or the manufacturer of the medical electronic
equipment before using this device.
To avoid accident or injury to your skin or body, do not use
under the following conditions:
· While pregnant or nursing or during menstruation
· While growing or during adolescence
· If you suffer from atopic dermatitis or have unusually sensitive skin
· If you have skin allergies or bleeding diathesis
· If you have skin irritation or redness caused by sunburn
· There is suppuration or inflammation of the skin
· You experience skin irritation caused by cosmetics
· Have itchy pigmentation or pathologic pigmentation
· Have viral warts or melanoderma
· Have abnormal blood pressure
· Have weak skin sensibility
· If you are sick or feeling unwell
· If you have capillary dilatation due to long term use of steroid
hormonal drugs or a disorder of liver function
· If you are under a doctor's care
Do not use if you suffer from any of the following conditions,
or on body areas listed below as this may cause injury:
Acute disorder, febrile disorder, contagion, fissures, unusual warts,
feeling unwell, extremely exhausted, tuberculosis, abnormal blood
pressure, malignancy, heart disease, blood or visceral disease,
epilepsy, photo sensitive, or if you have consumed alcohol or
medication that causes drowsiness.
Do not use on wounds, scars, parts of skin that are darker than your
usual skin tone including tattoos, body painting, dark brown spots, or
moles.
Do not use inside mouth or around the pubic area, lips, mucous
membranes, over the Adam's apple, on eyelids or eyeballs, or
around the eyes.
Do not use on areas where you have had plastic surgery.
Do not use on or around eyebrows, forehead, head, ears, nipples,
areola, inside umbilicus, large veins, or over acne.
If you are not sure, consult your doctor before use.
Safety Precautions
21
Safety Precautions
Do not use the device for
extended periods.
(Not for professional use.)
Allow at least 10 minutes interval
aft er 2 0 m in ut es o f use . No t
fo ll ow ing t hi s in struc ti on m ay
caus e the glass tube to crack or
overheat, or may cause injury.
Do not use the device near
flammabl e s ubs tan ces or
ob je cts suc h as alcoho l,
t h inne r, b e n z e ne, na il
po lish re mover , or sp ray
can s as thi s may ca us e
f i r e , e l e c t r i cal s h o c k
hazard, or injury.
If you do no t h ear the fan
runni ng when u sin g th e
Flash mode, i mmediate ly
discontinue use.
(Hearing a buzzing tone is
normal.)
Con ti nu ed us e of th e dev ic e
und er t his cond itio n may cause
smoke, fire, malfunction, or risk of
injury. Consult your local agent if
repair is needed.
Do no t da mage, m od ify,
be nd by f orce, or bun dle
the cord.
Do not place heavy objects
on the cord or al low i t to
get pi nc h ed in be twe en
other obj ect s a s this may
damage the cord and cause
a fi re or e le ctrical s hock
hazard.
I f an y pr ob l e m occ ur s
d u r ing use , in clu di ng
abnorma l odor, smoke, or
exces s hea t, disco nti nue
use since this may cause
damage or fire.
Do not d rop , h it, or place
heavy objects on the main
un it a s this ma y ca us e a
m alf u nct i on, c r ack the
glass tube, or cause injury.
Do n ot look dir ec tl y into
t h e t r eatment windo w
(f lash) or a llow other s to
look at the emitting flash.
Do no t use t he devic e in
dark pl ac es as t his m ay
cause eye injury or c ause
the device to malfunction.
Do not point the treatment
window at a black object as
this may cause the device
to not work properly.
D o n o t u s e i f th e AC
adapter is damaged or the
wall socket is loose as this
may cause electrical shock
hazard, s ho rt ci rc ui t, or
fir e. Co n su l t you r l oca l
agent for repair.
Do n ot m ove or l ift the
main unit by pulling the AC
adapter.
D oi n g s o m a y c a u s e
el ectrical sh oc k ha zard,
s h o r t ci r c u i t , fire , o r
disconnection.
Use only as directed in this
instruction manual.
Improper use may cause
injury or malfunction.
WARNINGWARNING
Do not allow the main unit,
AC adapter, or cord to get
wet.
Do n ot use or s tore ne ar
water or humid places such
as bath rooms as this may
cause an electri cal shock
hazard , short circuit, fire,
or malfunction.
Use at AC100-240V only.
Make su re the AC adapter
i s fir ml y a n d secu re ly
p l u g g e d i n t o th e wa l l
s ocke t w h ile in u s e t o
a v oid a p ot en tia l fi re ,
electrical shock hazard, or
malfunction.
Use only the supplied AC
adapter to avoid electrical
shock hazard, short circuit,
fire, or malfunction.
C h e c k a n d c l e a n th e
tre a tme n t w i ndo w on a
regular basis to avoid risk
of burns or malfunction.
If any problem occurs
during use, unplug the AC
adapter immediately.
D isc on t i nue u s e if t h e
de vi ce d oe s not operate
pro perly, or emits smoke,
an unusual noise, or odor.
Unp l ug t he A C a d apt e r
from the wall socket when
not in use or when cleaning
t o a v o i d a p o t e n t i a l
el ectrical sh oc k ha zard,
short circuit, or fire.
Do n ot a ll ow c hi ld re n or
di sa bl ed p er so ns to use
the device unattended.
If you are underage, do not
u se w i tho u t a p a ren t' s
pe rmissio n and o nly u se
under parental supervision
to avoid injury.
Do n ot u se an exten si on
cor d a s t his ma y c au s e
da ma ge , overheating , or
fire hazard.
D o n o t d i s a s s e m b l e ,
attempt to repair, or modify
this dev ice in any way as
t h i s ma y c au se a fi re,
electrical shock hazard, or
injury . C onsult you r l ocal
agent if repair is needed.
Hold the hea d o f the plug
in stead of the cord when
unp lu ggi ng th e a dap ter
fr om t he w al l socket. Be
caref ul not to to uc h the
metal prongs or parts . Do
not handle with wet hands.
Dam age to th e c o rd ma y
ca us e an el ec trical sh ock,
short circuit, or fire hazard.
Do no t pla ce the de vic e
near fire, flame, flammable
o b j e c t s, un d e r d i r e c t
s u n l i g h t , or i n h u m i d
p l a c e s s u c h a s t h e
bathroom. Do not dispose
of i n a fi re o r place near
heating equipment as this
may c au se over he at ing,
malfunction, fire hazard, or
explosion.
Safety Precautions
43
Safety Precautions
Ma ke s ur e th e tr ea tm ent
w ind ow i s no t b r oken ,
di st or ted, disc ol or ed , or
damaged.
D o n o t u s e i f you see
damage or broken parts on
t he d evi c e a s t his may
w orse n t he da m a g e o r
cause burns or injury to the
skin or fingers.
Do not use more than once
a day o n th e sam e ar ea.
Excess treatment does not
improve effectiveness.
For best results, follow the
t r e a t m e n t f r e q u e n c y
recommendations (p.12).
D o n ot appl y f lash on
cl othes, ob jects , or yo ur
h e a d hair a s t his may
cause burns, discoloration,
or damage.
Do n ot a pply perfum e or
makeup on areas that have
ju st b een treat ed a s this
may cause skin problems.
(N ot including skin car e
products for moisturizing.)
Do not wipe the device with
solvents such as alcohol,
t h inne r, b e n z e ne, na il
polish remover, as this may
c a use d a ma g e t o t h e
surface of the main unit.
Tr eatment a re as m ay b e
slightly over lapped during
a treatment.
Do no t pla ce the de vic e
n e a r o b j e c t s th at a r e
suscept ible to magnetism
as this may cause damage
to the objects, or result in a
malfunction of the device.
Do not apply antiperspirant
r i ght af te r p e rfor mi ng
tr eatme nt on unde ra rms.
R efra in f rom us e u nti l
red ness completely fades
away.
Do not use out of doors or
un de r direct sunlight a s
this may cause malfunction
or the device may not work
properly.
D o not us e on pe ts o r
animals as this may cause
injury.
D o n o t u se i f y o u a r e
exp er ien ci ng sk in ra sh,
irr i tat ion , o r it c hi n ess .
Dis co nti n u e us e i f you
ex perience an a bn or ma l
ski n r eac t io n d u ri n g o r
after treatment.
Use a mo i s tu ri zer o n a
daily basis to prevent your
skin fr om ov er dry in g. If
yo ur skin i s too d ry, you
m a y n o t ge t t h e b e s t
results.
Brush away any hair debris
on th e s kin as t his ma y
cau s e y our sk in t o f eel
mor e he a t d uri n g f l as h
emission.
CAUTIONCAUTION
Always shave the treatment
area before applying flash
tre a tme n t. If y ou a pp l y
flash to skin with long hair
remaining, hair debris may
adh er e t o the t rea tm ent
wi ndow an d cause burns
o n t he w ind ow . Gen t ly
rem ove hair de bris or dirt
from the treatment window
using a cotton tip.
A l w a ys r e f e r to Af t e r
Treat men t section i n this
instruct ion ma nual (p.19)
aft er ea ch us e. Re mov e
hair debris and cosmetics
fr om the ma in u nit sin ce
this may cause skin burns,
a mal fu n c tion , o r ski n
irritation.
U se o nly i n t he pro p e r
operational environmental
temperature of 5°C - 35°C.
Check the te mperature of
the environment you are in
before using the device to
prevent pos sib le damage
or malfunction.
NOTE: If there is a sudden
change i n t emp erature, it
may take some time for the
device to adapt to the new
environment.
Avoid sun or UV exposure
to ar eas t hat h ave b een
treated for at least 24 hours
after treatment. If redness
rem ai n s aft er 24 ho urs ,
c o ntin ue t o av oi d s u n
e x p o s u r e . Al s o a p p l y
su nscre en to p rotect the
skin duri ng the treatment
pe riod to avoi d poten tial
skin problems.
If your s ki n con ti nues to
fee l warm after treatment,
you can cool down the skin
com pl ete l y w it h a c old
towel.
S kin may r ema i n w a r m
after treatment depending
on your body condition or
o n h o w th e de vi c e h a s
b e en u se d. I f th e sk in
warmth bothers you, follow
instructions (p.14 sec.7) to
treat the symptom.
If th is sympt om do es not
i mpro ve , c onsu lt y o ur
doctor.
Av oi d ex er ci se , ba th in g
in a hot tu b, o r drink in g
alcohol until the day after a
t r eatme nt a s thi s ma y
cause skin irritation.
Safety Precautions
Always us e an in te ns ity
le vel tha t is s ui table for
your skin. Refer to “How to
set the Flash level” (p.11)
If using the device for the first
time, or until you get used to
using the device, always start
from level 1.
Make su re th er e are n ot
any dark or blac k objects,
cos met i cs , d i rt , or ha ir
debri s o n the attac hment
bef o re u se as t his ma y
cause skin burns, damage
the attachment, or lead to a
possible malfunction.
65
Use in Foreign Countries
WARNING
Use in Foreign Countries
Use at AC 100 -240V only to av oid a potential fir e or electrical
shock hazard.
Be sure to check the plug shape and the voltage before using.
Us ing t his d ev ice w ith a n impro per p lug o r at th e inc orrec t
voltage may cause overheating, fire, or malfunction.
NOTE: This product can be operated at 100-240V. If the plug of the
supplied AC adapter does not match the plug of your location, use a
plug adapter (not provided).
Main plug configurations and countries of use
Type Plug Configuration Countries of Use
A
B3
BF
C
US, Canada, Hawaii, Spain, Guam,
Saipan, Thailand, Korea, Taiwan, China,
Philippines, Vietnam, Brazil, Turkey, etc.
UK, Switzerland, China, Hong Kong,
India, Singapore, Philippines, Egypt,
South Africa, etc.
Canada, UK, Switzerland, Thailand,
Korea, Singapore, China, Hong Kong,
Egypt, South Africa, etc.
Italy, Holland, Switzerland, Spain,
Germany, France, India, Thailand, Korea,
China, Hong Kong, Malaysia, Turkey, etc.
UK, France, Australia, New Zealand,
O
The plug configuration and voltage varies depending on the region and
the type of accommodation. Always be sure to check for compatibility
before using the device.
Fo r infor mation ab out p lu g ada pt ers, co nsult a travel agency o r a
consumer electronics retailer.
Korea, Taiwan, China, Philippines,
Argentina, etc.
Main Unit
Product Description
Glass Tube
(Flash)
Treatment
Window
(Shown in grey)
* Yellow Clear
Glass
Accessories
Filter
Emission
Button
Cool Plate
(For skin cooling)
Standby Lamp
Product Description
Vents
* Do not block
AC Adapter Socket
AC AdapterFace Attachment
AC Adapter
Adapter Plug
* Design and specifications of the main unit and accessories
are subject to change for improvements without prior notice.
87
Operation Panel
Before Use
Level
Indicator
Lamp
Before Use
Level Down
Button
Standby
Lamp
Level Up
Button
Mode Lamp
Power / Cool Button
Emission
Button
Power / Cool Button
ON: Press and hold (approx. 3 sec.) to turn ON
(Level 1 lamp will be solid green)
COOL: Press (approx. 1 sec.) to switch to Cool Mode
(Mode Lamp is solid blue)
OFF: Press (approx. 3 sec.) to turn OFF
(Lamps are off)
The fan will run for about 90 seconds after power is turned off.
Do not unplug the AC adapter until the fan stops running.
Level UP and Level DOWN Buttons
Set the treatment intensity. There are 5 adjustable levels.
With each press of a Level button, the corresponding Level lamp will turn
solid green. At maximum, all 5 Level lamps will be lit.
The higher the level, the more warmth you may feel when using Flash.
Be sure to start from Level 1 until you get used to treatment.
Standby Lamp
Lamp off: The unit is in standby (waiting), or the treatment window is not
entirely covering the treatment area.
Solid green: Treatment window is properly touching the skin and pressing
the Emission button will emit flash.
You will hear two short beep tones when the unit is ready for treatment.
Preparing for Treatment
Follow these instructions before every treatment for best results.
Shave the treatment area with your own shaver.
1
Unwanted hair or debris on the skin surface may cause burns.
Do not pluck or wax unwanted hair on areas you wish to treat.
Make sure the attachment and treatment window are clean,
2
free of dirt and debris, undamaged, and in good condition.
Always clean the treatment window if it is dirty to prevent malfunction,
deterioration, burns, injury, and skin irritation.
Refer to the section “How to Clean” (p.19) for details on cleaning.
Before Use
109
Set the Flash Level
Set to a level at which you feel a mild sensation of warmth
or heat. Do not use at a level that is intolerable.
Adjust the Flash level according to the treatment area.
Do not set the flash level high for those with dark skin tone or
recently tanned skin. Doing so may cause skin irritation.
Before Use
Test the Flash on a patch of skin
Please follow these instructions prior to your first treatment.
Press and hold Power / Cool button for approx. 3 seconds
1
to turn on the power.
Body: No attachment needed.
Face: Use the Face attachment.
* When using the Face attachment, attach it to the treatment
head after turning on the power.
Test the flash on a patch of skin near the area you plan to
2
treat starting at Level 1.
See section “How to Use Flash Mode” on p.13.
Wait 24 hours and then examine the treatment area.
3
If the skin appears normal (skin condition without any redness,
blisters, or burns), then start your first treatment.
Treatment
Treatment Steps
< Body Care >
①
Shave →
②
Apply flash treatment →
③
Cool down the treatment area using Cool mode
NOTE: If unwanted hair is longer than 1mm, always shave first before
performing flash treatment.
< Face Care >
①
Attach Face Attachment and then perform flash treatment →
②
Remove Face Attachment →
③
Cool down the treatment area using Cool mode
NOTE: Shave long unwanted hair, unwanted dark hair, and hair
around the mouth before performing flash treatment.
Frequency of Treatment
Treatment
During first 2 months
Every 2 weeks Once in 4-8 weeks
Do not apply flash on the same area more than once a day.
The results vary from person to person and depend on which body area is treated.
If you are not satisfied with the results, continue to treat every 2 weeks for more
than 2 months until you see the desired results.
This device is not designed for permanent hair removal.
If regular treatment is discontinued, it may be difficult to see results and you may
find that unwanted hair will gradually grow back.
Do not use more often than the recommended frequency of
treatment above.
If you wish to treat the area more than the recommended treatment
CAUTION
frequency, always check your skin condition before and during use.
Do not apply flash on the same area more than once per day as this
may cause skin irritation or damage.
After 2 months of treatment
1211
How to use Flash Mode
Plug the AC adaptor into the adapter plug socket and then
1
into the wall socket.
Press and hold the Power/Cool button (approx. 3 seconds)
2
to turn on the power
When using an attachment, first turn on the power and then attach
the attachment.
Treatment
Level 1 indicator lamp will turn on solid green.
When the power is on, you will hear a humming sound from the
internal fan. This is normal.
Press the Level UP or Level DOWN buttons to set the
3
treatment level.
This device offers 5 intensity levels for Flash treatment.
Always start from level 1 until you get used to treatment.
When you hear two short beep tones, the device is ready for
treatment.
How to Use Each Mode
Place the treatment window flat against the skin and press
4
the emission button.
The flash will only emit if the standby lamp turns solid green.
Continue pressing the emission button to switch to repeat flash
emission mode (p.15).
Do not look directly into the treatment window when applying
flash.
Apply to skin as shown above.
Move the treatment window to the next
5
adjacent area after each flash to continue
applying treatment to the entire area.
Move to the next area after each flash even
when using repeat flash emission mode.
The treatment window is the size of the area
that will receive each flash emission.
Press and hold the Power/Cool button (approx. 3 seconds)
6
to turn off the power.
All the lamps will turn off when the power is off
The fan will run for about 90 seconds after power is turned off.
Do not unplug the AC adapter until the fan stops running.
If the skin remains hot after the treatment, use the Cool
7
mode or a refrigerant or cold towel to cool down the
treatment area. Then apply a moisturizer to soothe the
treatment area.
When you are finished, unplug the AC adaptor from the
8
wall socket and clean the main unit and attachment.
Follow instructions for “How to Clean” described on p.19. Clean
the unit and accessories after every use.
Do not bathe (showering is OK), exercise, or drink alcohol after
any treatment session until the next day.
Treatment
This device has a built-in safety feature which only allows the flash to
work when the treatment window is completely flat against the skin
and blocking ambient light. Never use in a dark room since this may
defeat the safety feature and could harm your eyes.
The device may not operate properly under direct sunlight.
The power will automatically turn off 20 minutes after turning on the
power. Allow at least a 10 minute interval before the next use to avoid
malfunction.
The device cannot be used in a dark room.
At higher intensity levels, the standby time (waiting period) will be
longer.
1413
< About Single/Repeat Emission Mode >
If you continue to press the emission button, the flash will repeatedly emit
automatically each time the device is ready to flash again. Glide the
treatment window (without lifting) to a new area after each flash.
Do not use in dark areas; this may cause eye injury.
Do not emit flash directly into eyes; may cause eye injury.
Do not emit the flash on your head hair when using the
device on the face. Pull your hair back to keep hair away from
your face during treatment.
Do not touch the filter after use as this may cause burns
and injury to fingers.
Treatment
WARNING
Do not use on these areas to avoid skin problems or injuries:
Wounds (scars, or parts of skin that are darker than your
usual skin tone)
Eyeballs
Eyelids, or around eyes
Pimples
Brown spots, moles
Eyebrows, forehead, head hair
Tanned skin
How to use the Cool Mode
Cool down the treatment area after a flash treatment.
Press Power/Cool button for approximately 1 second to
1
switch to Cool mode while the device is turned on.
The Mode lamp will turn on solid blue.
Apply Cool Plate to the treatment area.
2
Move the device in the direction shown in
the figure at right.
Cool mode does not have adjustable
temperature level settings.
Press and hold the Power/Cool button for approximately 3
3
seconds to turn off Cool mode if you wish to finish.
The solid blue lamp will turn off when Cool mode is off.
If you wish to apply another flash treatment to a different area, press
the Power/Cool button for approximately 1 second to switch back to
flash mode.
Do not use Cool mode successively.
If not allowed to rest between applications, the Cool Plate will
CAUTION
not fully reach its proper cooling state. Allow at least a 10
minute interval before next use.
Treatment
1615
Tips for Each Treatment Area
Follow these tips for application to different treatment areas:
Underarm Treatment
Remove all cosmetics, antiperspirants, perfumes, and lotions before
treatment.
Use a mirror for an easier view of the treatment area. Stretch the skin with
your fingers where skin is loose.
You may feel heat if loose skin gets near to the treatment window.
Face Treatment
Always use the Face Attachment when treating facial areas.
Avoid sun exposure right after treatment and also avoid getting a tan
Treatment Area Tips
during the treatment period.
Stretch narrow or angled areas such as around the mouth which may be
more difficult to reach for treatment (e.g. moustache or beard).
* Never look directly into the flash.
Bikini Line Treatment
Use lower levels on areas that have more pigmentation (parts of skin that
are darker than your usual skin tone).
*Always start from level 1 if you are treating for the first time or unfamiliar
with use.
Arms / Legs Treatment
Skin over bone or lumpy areas may be sensitive compared to other body
areas and may be more likely to result in some redness.
In such cases, cool down the treatment area by using the Cool mode and
apply a moisturizer after treatment.
WARNING
Do not use on these areas to avoid skin problems or injuries:
Wounds (scars, or parts of skin that are darker than your
usual skin tone)
Eyeballs
Eyelids, or around eyes
Pimples
Brown spots, moles
Eyebrows, forehead, head hair
Tanned skin
About the Face Attachment
Proper treatment on the face or small areas can be performed by
attaching the face attachment to the device.
The Face attachment is always recommended for use on facial hair.
Attaching and Removing Face Attachment
Always attach or remove the Face attachment while the power is ON.
Fasten the Face Attachment to the treatment window as shown in the
figure below. The attachment will magnetically stay in place.
Make sure the Face Attachment is securely attached to the device.
Hold the attachment carefully when removing.
Face Attachment
Recommended Attachment for Treatment Areas
Area
Face
Underarms
Arms
Legs
Fingers
◆
◆
◆
FaceNo Attachment
◆
◆
Using Attachments
1817
After Treatment
How to Clean Attachment and Main Unit
Treatment window and cool plate must be cleaned every time after
each treatment.
Clean the main unit regularly to avoid malfunction or operation failure.
Always turn off the power and unplug the AC adapter from the main unit
and from the wall socket before cleaning.
Cleaning Treatment Window and Face Attachment
Use a wrung cloth to clean dirt, skin care product, or hair
1
debris from attachment, treatment window, and cool plate.
After Treatment
Gently remove any skin care product or dirt that may be on the inner
edges of the treatment window opening by using a cotton tip.
Also clean any dirt in the areas of contact between the treatment
head and Face Attachment with a wrung cloth.
Remove skin care or hair debris or dirt on the yellow glass
2
filter with a soft cloth or cotton tip.
Remove finger prints and keep the filter clean. Dirt or debris may
cause the filter to overheat, degrade performance of the flash, lead to
a malfunction, or cause skin irritation.
Remove any dirt or debris from the attachment filter as well.
Cleaning the Main Unit
Use a wrung cloth to clean dirt from the surface.
1
Use a sponge or cloth with diluted mild detergent
for heavy dirt.
Never wipe the device with solvents such as
alcohol, thinner, benzene, or nail polish remover.
WARNING
CAUTION
Unplug the AC adapter from the wall socket when cleaning.
Cleaning with the adapter attached may cause electrical
shock hazard, short circuit, or fire.
Keep water from entering inside the unit as this may cause
electrical shock hazard, short circuit, or fire.
Never use solvents such as alcohol, thinner, benzene, or nail
polish remover.
Do not leave or store the device with skin care product or
lotion residue remaining on the device.
How to Store
If you will not be using the device for an extended period, clean the main
unit and the attachment before storing.
When not in use, turn off the power, unplug the AC adapter from the wall
socket, and store in a clean, dry location.
Do not use or leave the device near stoves or heaters, under direct
sunlight, in humid places such as the bathroom, or in an unstable place.
Keep this device out of the reach of children.
Maintenance and Inspection
If you have not used the device for an extended period, inspect it
carefully and check that the device works properly and safely before use.
If there is any evidence of a malfunction, refer to the “Troubleshooting”
section (p.21) before calling for service.
If the device malfunctions, appears damaged, or needs service, please
contact your local distributor.
After Treatment
2019
Troubleshooting
Checklist for Possible Problems
Symptom Possible Cause Solution
Power does not
turn on
Troubleshooting
The power turns off
Flash does not emit
any light
AC adapter is not
connected to main
→ →
unit or wall socket
You did not press
the Power/Cool
→ →
button for 3 seconds
Turned off after 20
minutes from when
→ →
the power was
turned on
You tried to turn on
in a dark area - the
→ →
power will turn off
with a beep (error).
AC adapter is not
connected to wall
→ →
socket or is using an
extension cord
Flash emission
→ →
button not pressed
The device is waiting
→ →
to recharge the flash
Treatment window is
not entirely covering
→ →
the skin surface
Connect AC adapter
to main unit and plug
into wall socket
Press and HOLD
Power/Cool to turn
on the power
Allow the device at
least a 10 minute
interval before the
next use
Use only in a well lit
place; attach Face
Attachment after
power is turned on
Connect AC adapter
and plug directly into
wall socket (do not
use extension cord)
Press the flash
emission button
Wait until you hear
two short beeps
Hold window flat
against skin until the
Standby lamp turns
solid green (p.13)
Symptom Possible Cause Solution
Flash does not emit
any light
Flash treatment
feels too hot or is
painful
The flash is too
bright
The treatment is set
→ →
to Cool Mode
You are using it in a
→ →
dark place
You are using it
→ →
under direct sunlight
The intensity level is
→ →
set too high
Used over once
→ →
daily on same area
Unwanted hair or
debris is left on the
→ →
surface of the skin
Used over tanned
→ →
skin or a mole
The treatment
window is not
→ →
entirely covering the
skin surface
Press Power/Cool
button for 1 sec. to
switch to Flash mode
Use in an area with
brighter lighting
Use where you can
avoid direct sunlight
Press the LEVEL
button to lower level
Don't use more than
once on same area
Remove unwanted
hair and flick away
debris on the skin
Do not treat certain
areas (see p.2)
Hold the treatment
window against the
skin. If you feel the
flash is too bright,
wear sunglasses.
Troubleshooting
Cool plate does not
get cool
You hear a buzzing
sound
You are using the
device successively
→ →
for more than 20 min
Device is not set to
→ →
Cool Mode
This is the internal
fan operating and is
→
normal.
Turn off power and
allow device to rest
for about 10 minutes
Press and hold the
Power/Cool button
for 1 sec. to switch
to Cool mode(Mode
lamp is blue)
2221
FAQ (Frequently Asked Questions)
Q A
Intense, instant light from a Xenon flash lamp.What is Flash?
Will the flash feel
hot, hurt, or will my
skin get red?
What should I do if I
cannot remove dirt
FAQ
from the filter?
How many times can
I use flash treatment
in a day?
Why do I smell
something is burning
right after I use the
flash?
You will feel a mild heat when flash is used but it
does not affect the skin.
Possible reasons the flash may feel hot is
because a longer hair was treated, or you have
recently been tanned. Always shave unwanted
hair and do not get tanned before treatment.
If you experience redness or pain, immediately
discontinue use and cool and moisturize your
skin. If the symptoms do not fade away, consult
a doctor.
If the dirt does not come off even after you
attempt to clean it, consult your local agent.
Do not use the flash more than once over one
area in a day as this can cause skin irritation.
Because the flash has been absorbed by and
heated the hairs you are treating.
If you smell an unusual odor from the device
itself, immediately discontinue use and turn off
the power and then unplug the AC adapter.
Consult your local distributor for advice to avoid
possible skin problems.
After Service
About Disposal
Follow your local government rules for proper disposal of this product.
Recommended Skincare Product
(Sold Separately)
Platinum Esthe RB
Pearl Skin Gelée Lotion with SPF
Soybean extract and moisturizing ingredients will lead to
smooth and moisturized pearly skin.
Suitable for use after hair removal treatment.
Product name: Platinum Esthe RB Pearl Skin Gelée Lotion
Content: 150mL
Made in Japan
After Service
2423
STA170-1-001E
Loading...