Yamaha Audio SPM-10TV User Manual

SPEAKER BRACKETS

Special for use with NS-10MM

SPM-10TV

Thank you for selecting this Yamaha SPM-10TV speaker mounting brackets. This model is designed specially for use with
Yamaha NS-10MM speaker system.

n PRECAUTIONS

Read the following precautions carefully before mounting
your NS-10MM using these brackets.

● Do not use these brackets for mounting speakers other
than NS-10MM.

● Mount these brackets on a TV rack etc. firmly by using
commercially available wood screws.
Mount the brackets properly and securely by following this
manual. If the brackets are mounted improperly, they may
fall down and you may be injured.

● Use commercially available wood screws which is proper
for using on the board of TV rack. If you use a wood
screw which is longer than the thickness of board and it is
tightened through the board, you may injure yourself in
the hand when you insert a hand into the TV rack.

● If your TV is a revolving type, mount the speakers and the
brackets so that they will not touch the TV when the TV is
revolved.

● Make sure to place these brackets on a flat surface. If
placed on an uneven surface, they may fall down and you
may be injured.

● To avoid accidents resulting from tripping over loose
speaker cables, fix them to the wall.

● Do not attempt to clean the brackets with chemical
solvents as this might damage the finish. To clean, wipe
with a dry, soft cloth.

● To prevent the brackets from discoloring or being
corroded, do not place the brackets where they will be
exposed to direct sunlight or excessive humidity.

● Secure placement or installation is the owner’s
responsibility. YAMAHA shall not be liable for any
accident caused by improper placement or
installation of the brackets.

n MOUNTING SPEAKERS

Notes

● Mount the speaker to the bracket so that the speaker
faces the front as figured below.

● Make mounting by using the provided bolts and washers.
For tightening bolts, use the provided hexagonal wrench.

Procedure

1.Put the provided pads A on the bracket as figured below.

(Put the pad A carefully. Putting and removing the pad
repeatedly may tear it off.)

2.Before mounting the speaker to the bracket, insert a bolt

and a washer into the hole on the bottom of the speaker
which is closer to the TV, and tighten the bolt to about
80%.

3.Pass the head of the bolt tightened on the speaker

through the hole (marked *on the figure above) on the
bracket, and slide the head of the bolt to the narrow part
of the hole.

4.Mount the speaker to the bracket by inserting a bolt and a

washer into the other hole as figured below.

5.Tighten both bolts fully.

Pad A

INSTALLATION MANUAL

Pad A

*

n ACCESSORIES

Pad A x 4
(VV777700)

Pad B x 1
(VV777800)

Hexagonal wrench x 1
(VV778000)

Two-sided tape x 2
(VV876500)

Bolt (diam. 4 mm) x 4
(VB514900)

Washer (diam. 4 mm) x 4
(ET500040, black)

Logo plate x 2
(VV777900)

Washer
(diam. 4 mm)

Bolt
(diam. 4 mm)

(Right side)

n PLACING THE BRACKETS

60

B5.5

B5.5

B5.5

B5.5

B5.5

B5.5

60

150 70

244.4

60

70

180

1.Put the provided pads B to parts of the bracket or the

speaker where the TV touches as figured right. (This can
prevent sound from vibrating.)

2.Put the provided two-sided tape*

1

on the bottom surface

of the bracket as figured right.

3.Place the bracket on the TV rack and press it down to fix it

on the TV rack with the two-sided tape temporarily.

4.Fix the bracket on the TV rack firmly by using wood

screws*2, and then place the TV on it.

5.Remove the paper on the reverse side of the provided

logo plate, and put the plate on any desired part of the
bracket.

1

: If you remove the two-sided tape put on the TV rack,

*

remove it carefully so that the dressed outer layer of the
rack is not peeled off or a mark from the tape is not left
on the rack.

2

: Wood screws are not provided. Use commercially

*

available wood screws with a diameter of 3.5 mm to 4
mm.

Wood screws

Pad B

Two-sided tape

Bracket

TV rack

Wood

3.5 mm to 4 mm

Note

Do not mount the brackets on a TV rack whose board is thin
or hollow. If wood screws are used on such a board,
sufficient stability and security will not be obtained.

n DIMENSIONS n SPECIFICATIONS

Top

Front

Unit: mm

Side

Dimensions (W x H x D) ...................... 244.4 x 180 x 70 mm

Weight .............................................. 0.5 kg/pc. (1 lbs. 2 oz.)

(9-5/8” x 7-1/16” x 2-3/4”)

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA