Yamaha Audio RX-V800RDS User Manual

RX-V800RDS

Natural Sound AV Receiver Ampli-tuner audio-vidéo

G B

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

1 To assure the finest performance, please read this

manual carefully. Keep it in a safe place for future reference.

2 Install this unit in a well ventilated, cool, dry, clean

place with at least 30 cm on the top, 20 cm on the right and left, and 10 cm at the back of this unit — away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold.

3 Locate this unit away from other electrical

appliances, motors, or transformers to avoid humming sounds. To prevent fire or electrical shock, do not place this unit where it may get exposed to rain, water, and/or any type of liquid.

4 Do not expose this unit to sudden temperature

changes from cold to hot, and do not locate this unit in a environment with high humidity (i.e. a room with a humidifier) to prevent condensation inside this unit, which may cause an electrical shock, fire, damage to this unit, and/or personal injury.

5 On the top of this unit, do not place:

– Other components, as they may cause damage

and/or discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause

fire, damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may cause

electrical shock to the user and/or damage to this unit.

6 Do not cover this unit with a newspaper, tablecloth,

curtain, etc. in order not to obstruct heat radiation. If the temperature inside this unit rises, it may cause fire, damage to this unit, and/or personal injury.

7 Do not plug in this unit to a wall outlet until all

connections are complete.

8 Do not operate this unit upside-down. It may

overheat, possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cord from the wall

outlet, grasp the plug; do not pull the cord.

11 Do not clean this unit with chemical solvents; this

might damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used.

Using this unit with a higher voltage than specified is dangerous and may cause fire, damage to this unit, and/or personal injury. YAMAHA will not be held responsible for any damage resulting from use of this unit with a voltage other than specified.

13 To prevent damage by lightning, disconnect the

power cord from the wall outlet during an electrical storm.

14 Take care of this unit so that no foreign objects and/

or liquid drops inside this unit.

15 Do not attempt to modify or fix this unit. Contact

qualified YAMAHA service personnel when any service is needed. The cabinet should never be opened for any reasons.

16 When not planning to use this unit for long periods

of time (i.e. vacation), disconnect the AC power plug from the wall outlet.

17 Be sure to read the “TROUBLESHOOTING” section

on common operating errors before concluding that this unit is faulty.

18 Before moving this unit, press STANDBY/ON to set

this unit in the standby mode, and disconnect the AC power plug from the wall outlet.

This unit is not disconnected from the AC power source as long as it is connected to the wall outlet, even if this unit itself is turned off. This state is called the standby mode. In this state, this unit is designed to consume a very small quantity of power.

■ For U.K. customers

If the socket outlets in the home are not suitable for the plug supplied with this appliance, it should be cut off and an appropriate 3 pin plug fitted. For details, refer to the instructions described below.

Note

• The plug severed from the mains lead must be destroyed, as a plug with bared flexible cord is hazardous if engaged in a live socket outlet.

■ Special Instructions for U.K.

Model

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL Brown: LIVE

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. Making sure that neither core is connected to the earth terminal of the three pin plug.

CAUTION

INTRODUCTION

CONTENTS ........................................................... 1

FEATURES ............................................................ 2

GETTING STARTED........................................... 3

Checking the Package Contents ............................... 3

Installing Batteries in the Remote Control ............... 3

CONTROLS AND FUNCTIONS ........................ 4

Front Panel ............................................................... 4

Remote Control ........................................................ 6

Description of the Numeric Buttons......................... 7

Using the Remote Control ........................................ 8

Front Panel Display .................................................. 9

Rear Panel .............................................................. 10

PREPARATION

SPEAKER SETUP .............................................. 11

Speakers to Be Used ............................................... 11

Speaker Placement ................................................. 11

CONNECTIONS ................................................. 12

Before Connecting Components ............................ 12

Connecting Audio Components ............................. 12

Connecting Video Components .............................. 14

Connecting the Speakers ........................................ 16

Connecting to an External Amplifier ..................... 18

Connecting an External Decoder ............................ 18

IMPEDANCE SELECTOR Switch ....................... 19

Connecting the Power Supply Cords...................... 19

ON-SCREEN DISPLAY (OSD) ......................... 20

OSD Modes ............................................................ 20

Selecting the OSD Mode ........................................ 20

SPEAKER MODE SETTINGS ......................... 21

Summary of SPEAKER SET Items

1A through 1E .................................................... 21

ADJUSTING THE SPEAKER

OUTPUT LEVELS ......................................... 22

Before You Begin ................................................... 22

Using the Test Tone (TEST DOLBY SUR.) .......... 22

BASIC OPERATION

BASIC PLAYBACK ............................................ 24

Input Modes and Indications .................................. 26

Selecting a Sound Field Program ........................... 28

Normal Stereo Reproduction .................................. 29

TUNING ............................................................... 30

Connecting the Antennas........................................ 30

Automatic (or Manual) Tuning .............................. 31

Presetting Stations .................................................. 32

Tuning in to a Preset Station .................................. 33

Exchanging Preset Stations .................................... 34

RECEIVING RDS STATIONS .......................... 35

Description of RDS Data ........................................ 35

Changing the RDS Mode ....................................... 35

PTY SEEK Function .............................................. 36

EON Function ........................................................ 37

BASIC RECORDING ......................................... 38

ADVANCED OPERATION

SET MENU .......................................................... 39

Adjusting the Items on the SET MENU................. 39

1 SPEAKER SET (speaker mode settings) ........... 40

2 LOW FRQ TEST ............................................... 42

3 L/R BALANCE (balance of the

left and right main speakers) .............................. 43

4 HP TONE CTRL (headphone tone control)....... 43

5 CENTER GEQ (center graphic equalizer) ......... 43

6 INPUT RENAME .............................................. 44

7 I/O ASSIGNMENT ............................................ 44

8 INPUT MODE (initial input mode) ................... 44

9 PARAM. INI (parameter initialization) ............. 44

10 DOLBY D. SET (Dolby Digital set) ............... 45

11 DTS LFE LEVEL ............................................ 45

12 6.1/ES AUTO ................................................... 45

13 SP DELAY TIME ............................................ 46

14 DISPLAY SET ................................................. 46

15 MEMORY GUARD......................................... 46

ADJUSTING THE LEVEL OF THE EFFECT

SPEAKERS ...................................................... 47

SLEEP TIMER .................................................... 48

Setting the Sleep Timer .......................................... 48

Canceling the Sleep Timer ..................................... 48

REMOTE CONTROL FEATURES .................. 49

Selector Dial ........................................................... 49

Commonly Used Buttons in Any Position of the

Selector Dial ....................................................... 50

Controlling the Components

Connected to This Unit ...................................... 50

Button Names and Functions in Each Position ...... 51

Setting the Manufacturer Code .............................. 54

Programming a New Remote Control Function

(Learn Feature) ................................................... 55

Returning to the Factory Setting ............................ 56

ADDITIONAL INFORMATION

SOUND FIELD PROGRAM ............................. 57

Hi-Fi DSP Programs ............................................... 57

CINEMA DSP Programs ....................................... 58

MOVIE THEATER Programs ................................ 61

SOUND FIELD PROGRAM PARAMETER

EDITING ......................................................... 62

What is a sound field? ............................................ 62

Sound Field Program Parameters ........................... 62

Changing Parameter Settings ................................. 63

Resetting a Parameter to the Factory-set Value ...... 63

Digital Sound Field Parameter Descriptions .......... 64

APPENDIX

TROUBLESHOOTING...................................... 68

SPECIFICATIONS ............................................. 73

INTRODUCTION

PREPARATION

OPERATION

BASIC

OPERATION

ADVANCED

INFORMATION

ADDITIONAL

APPENDIX

English

Thank you for selecting this YAMAHA AV receiver.

FEATURES

Built-in 5-Channel Power Amplifier

◆ Minimum RMS Output Power

(0.04% THD, 20 Hz – 20 kHz) Main: 100 W + 100 W (8 Ω) Center: 100 W (8 Ω) Rear: 100 W + 100 W (8 Ω)

Multi-Mode Digital Sound Field Processing

◆ Digital Sound Field Processor (DSP)

◆ Dolby Pro Logic Decoder

◆ Dolby Digital/Dolby Digital Matrix 6.1 Decoder

◆ DTS/DTS ES Decoder

◆ CINEMA DSP: Combination of YAMAHA DSP

Technology and Dolby Pro Logic, Dolby Digital or DTS

◆ Virtual CINEMA DSP

◆ SILENT CINEMA DSP

Sophisticated AM/FM Tuner

◆ 40-Station Random Access Preset Tuning

◆ Automatic Preset Tuning

◆ Preset Station Shifting Capability (Preset

Editing)

◆ Multi-Functions for RDS Broadcast Reception

Other Features

◆ 96-kHz/24-bit D/A Converter

◆ “SET MENU” which Provides You with 15 Items

for Optimizing This Unit for Your Audio/Video System

◆ Test Tone Generator for Easier Speaker Balance

Adjustment

◆ 6-Channel External Decoder Input for Other

Future Formats

◆ BASS EXTENSION Button for Reinforcing

Bass Response

◆ On Screen Display Function Helpful in

Controlling This Unit

◆ S Video Signal Input/Output Capability

◆ Component Video Input/Output Capability

◆ Optical and Coaxial Digital Audio Signal Jacks

◆ Sleep Timer

◆ Remote Control with Preset Manufacturer Codes

and “Learning” Capability

• y indicates a tip for your operation.

• Some operations can be performed by using either the buttons on the main unit or on the remote control. In cases when the button names differ between the main unit and the remote control, the button name on the remote control is given in parentheses in this manual.

Manufactured under license from Dolby Laboratories.

Manufactured under license from Digital Theater Systems, Inc. US Pat. No. 5,451,942 and other world-wide patents issued and pending. “DTS”, “DTS Digital Surround” and “DTS ES” are trademarks of Digital Theater Systems, Inc. Copyright 1996 Digital Theater Systems, Inc. All Rights Reserved.

GETTING STARTED

Checking the Package Contents

Check your package to make sure it has the following items.

Remote control

Manganese batteries (4) (AAA, R03, UM-4)

INTRODUCTION PREPARATION

AM loop antenna

Indoor FM antenna

A/B/C/D/E

75-ohm/300-ohm antenna adapter (U.K. model only)

Installing Batteries in the Remote Control

Insert the batteries in the correct direction by aligning the + and – marks on the batteries with the polarity markings (+ and –) inside the battery compartment.

■ Notes on batteries

• Change the batteries periodically.

• Do not use old batteries together with new ones.

• Do not use different types of batteries (such as alkaline and manganese batteries) together. Read the packaging carefully as these different types of batteries may have the same shape and color.

Quick Reference Card

■ Changing batteries

As the batteries lose power, the operating range of the remote control decreases and the indicator does not flash or its light becomes dim. When you notice any of these conditions, change all of the batteries.

If the remote control is without batteries for more than 2 minutes, or if exhausted batteries remain in the remote control, the contents of the memory may be cleared. When the memory is cleared, insert new batteries, set up the manufacturer code and program any acquired functions that may have been cleared.

Note

• If the batteries have leaked, dispose of them immediately. Avoid touching the leaked material or letting it come into contact with clothing, etc. Clean the battery compartment thoroughly before installing new batteries.

OPERAIONT

BASIC

OPERATION

ADVANCED

INFORMATION

ADDITIONAL

APPENDIX

English

Front Panel

CONTROLS AND FUNCTIONS

STANDBY

/ON

SPEAKERS

BASS

EXTENSION

ON OFF

PROCESSOR

DIRECT

89 0

TUNER

DSP

A/B/C/D/E

EFFECT

PRESET/

TUNING

PROGRAM

1 STANDBY/ON

Turns on and sets this unit in the standby mode. When you turn on this unit, you will hear a click and there will be a 4 to 5-second delay before this unit can reproduce sound.

Standby mode

In this mode, this unit consumes a small amount of power to receive infrared-signals from the remote control.

2 Remote control sensor

Receives signals from the remote control.

3 Front panel display

Shows information about the operational status of this unit (see page 9).

4 INPUT MODE

Selects the mode of input for sources that send two or more types of signals to this unit (see page 26). You cannot control the input mode when you select 6CH INPUT as the input source.

5 INPUT l / h

Selects the input source (DVD, D-TV/LD, CBL/SAT, VCR 1, VCR 2/DVR, V-AUX, PHONO, CD, TUNER, CD-R, MD/TAPE) you want to listen to or watch.

INPUT MODE

DIGITAL

PRESET /TUNING

EDIT

PHONES S VIDEO VIDEO

SILENT

MEMORY

FM/AM

MAN'L/AUTO FM

TUNING

RDS MODE

MODE

AUTO/MAN'L MONO

EON PTY SEEK

/FREQ

MODE

L AUDIO R OPTICAL

VIDEO AUX

PRESET

FM/AM

/TUNING

EDIT

iopa

MEMORY

MAN'L/AUTO FM

DIGITAL

SURROUND

START

AUTO/MAN'L MONO

TUNING

MODE

INPUT

RDS MODE

/FREQ

BASS

–

EON PTY SEEK

MODE

VOLUME

START

sdf

6 VOLUME

Controls the output level of all audio channels. This does not affect the REC OUT level.

7 6CH INPUT

Selects the source connected to the 6CH INPUT jacks. The source selected by pressing 6CH INPUT takes priority over the source selected with INPUT l / h (or the input selector buttons).

8 SPEAKERS A/B

Turn on or off the set of main speakers connected to the A and/or B terminals on the rear panel.

9 BASS EXTENSION ON/OFF

When pushed in (ON), this feature boosts the bass frequency of the left and right main channels by +6 dB (60 Hz) while maintaining overall tonal balance. This boost is useful if you do not use a subwoofer. However, this boost may not be noticeable if “1B MAIN SP” on the SET MENU is set to SMALL and “1D LFE/ BASS OUT” is set to SWFR.

0 PROCESSOR DIRECT ON/OFF

When pushed in (ON), BASS, TREBLE, and BASS EXTENSION are bypassed, eliminating any alteration of the original signal.

–

TREBLE

6CH INPUT

CONTROLS AND FUNCTIONS

q EFFECT

Switches the effect speakers (center and rear) on and off. If you turn off the output of these speakers by using EFFECT, all Dolby Digital and DTS audio signals except for the LFE channel are directed to the main left and right channels. When Dolby Digital or DTS signals are mixed, the left and right main channel signal levels may not match.

w A/B/C/D/E

Selects one of the 5 preset station groups (A to E).

e PROGRAM l / h

Selects the DSP program (see page 28).

r PRESET/TUNING l / h

Selects preset station number 1 to 8 when the colon (:) appears next to the band indication on the front panel display, and selects the tuning frequency when the colon (:) does not appear.

t PHONES jack

Outputs audio signals for private listening with headphones. When you connect headphones, no signals are output to the OUTPUT jacks or to the speakers.

y VIDEO AUX jacks

Inputs audio and video signals from a portable external source such as a game console. To reproduce source signals from these jacks, select V-AUX as the input source.

u PRESET/TUNING (EDIT)

Switches the function of PRESET/TUNING l / h (the colon (:) turns on or off) between selecting a preset station number and tuning. This button is also used to exchange the assignment of two preset stations with each other.

i FM/AM

Switches the reception band between FM and AM.

o MEMORY (MAN’L/AUTO FM)

Stores a station in the memory. Hold down this button for more than 3 seconds to start automatic preset tuning.

p TUNING MODE (AUTO/MAN’L MONO)

Switches the tuning mode between automatic and manual. To select the automatic tuning mode, press this button so that the “AUTO” indicator lights up on the front panel display. To select the manual tuning mode, press this button so that the “AUTO” indicator does not light up.

a RDS MODE/FREQ

When an RDS station is received, press this button to change the display mode among the PS mode, PTY mode, RT mode, CT mode (if the station offers those RDS data services) and/or frequency display mode in turn.

s EON

Press this button to select the desired program type (NEWS, INFO, AFFAIRS, SPORT) when you want to tune in to a radio program of that type automatically.

d PTY SEEK MODE

Press this button to set the unit in the PTY SEEK mode.

f PTY SEEK START

Press this button to begin searching for a station after the desired program type has been selected in the PTY SEEK mode.

g BASS

Adjusts the low-frequency response for the left and right main channels. Turn the control to the right to increase or to the left to decrease the low-frequency response.

h TREBLE

Adjusts the high-frequency response for the left and right main channels. Turn the control to the right to increase or to the left to decrease the high-frequency response.

Note

• If you increase or decrease the high-frequency or the lowfrequency sound to an extreme level, the tonal quality from the center and rear speakers may not match that of the left and right main speakers.

■ Opening and closing the front

panel door

When you are not operating the controls behind the front panel door, close the door.

DIG

ITAL

INTRODUCTION PREPARATION

OPERAIONT

BASIC

OPERATION

ADVANCED

INFORMATION

ADDITIONAL

APPENDIX

To open, press gently on the lower part of the panel.

English

CONTROLS AND FUNCTIONS

Remote Control

This section describes the basic operation of this unit with the remote control. First, set the selector dial to the AMP/ TUN position. See “REMOTE CONTROL FEATURES” on pages 49 to 56 for full details.

1 2

Select the AMP/TUN position.

9 0

EFFECT

See page 7.

4 5

A/B/C/D/E

3 Numeric buttons (Input selector buttons)

These buttons select the input source. See pages 7 and 8 for the numeric buttons.

4 TEST

Outputs the test tone.

5 ON SCREEN

Selects the on-screen display (OSD) mode for your video monitor.

6 j / i

Adjust DSP program parameters and SET MENU items.

7 LEVEL

Selects the effect speaker channel (center, rear and subwoofer) so you can adjust their output level independently.

8 SLEEP

Sets the sleep timer.

9 INPUT

Switches the function of the numeric buttons to the input selector (see page 7).

0 Indicator

Flashes while the remote control is sending signals.

q Selector dial

Turn this dial to select the position for the component to be controlled. (The proper code must be set up for your component. See “Setting the Manufacture Codes” on page 54.) When the position is selected, the remote control is set to that component operation mode.

TV POWER

TV VOLUME

TV INPUT

1 DSP

Switches the function of the numeric buttons to the DSP program selector (see page 7).

2 Indicator window

Shows the name of components which can be controlled.

w A/B/C/D/E, PRESET–/+

These buttons are used to select a preset station. A/B/C/D/E: To select one of 5 preset station groups (A

to E)

PRESET –/+: To select a preset station number (1 to 8)

e u/d

Select DSP program parameters and SET MENU items.

r SET MENU

Enters the SET MENU.

t POWER

Turns on the power of this unit.

y STANDBY

Sets this unit in the standby mode.

CONTROLS AND FUNCTIONS

u VOLUME +/–

Increases or decreases the volume level.

i MUTE

Mutes the sound. Press again to restore the audio output to the previous volume level.

EFFECT

Switches the effect speakers (center and rear) on and off in the following cases:

• When the selector dial is set to the DSP/TUN position.

• While the indicator is lit for about 3 seconds after pressing DSP.

Description of the Numeric Buttons

The numeric buttons function in various ways depending on the position of the selector dial or the combination of other instructions.

■ When selecting an input source

Input selector buttons

■ When selecting a DSP program and turning on or off the effect speakers (center and rear)

A B

DSP program

group buttons

1 Press DSP regardless of the position of the

selector dial.

The indicator lights up for about 3 seconds.

2 You can select a DSP program with the

numeric buttons, turn on or off the effect speakers (center and rear) by pressing EFFECT and turn on or off the Dolby Digital Matrix 6.1 or DTS ES decoder by pressing

6.1/ES while the indicator is lit.

INTRODUCTION PREPARATION

OPERAIONT

BASIC

OPERATION

ADVANCED

1 Press INPUT regardless of the position of

the selector dial.

The indicator lights up for about 3 seconds.

2 You can select an input source with the

numeric buttons while the indicator is lit.

1 Set the selector dial to the DSP/TUN

position.

2 You can select a DSP program directly with

the numeric buttons, turn on or off the effect speakers (center and rear) by pressing EFFECT and turn on or off the Dolby Digital Matrix 6.1 or DTS ES decoder by pressing

6.1/ES.

INFORMATION

ADDITIONAL

APPENDIX

English

CONTROLS AND FUNCTIONS

■ When selecting a preset station number

1 Set code number “0023” in the AMP/TUN (or

DSP/TUN) position.

See page 54 for setting the code.

2 Set the selector dial to the AMP/TUN (or

DSP/TUN) position.

3 You can select a preset station number

directly with the numeric buttons (1 to 8).

See page 34.

Using the Remote Control

STANDBY

/ON

DIGITAL

TUNER

DSP

30° 30°

The remote control transmits a directional infrared beam. Be sure to aim the remote control directly at the remote control sensor on the main unit during operation.

■ Handling the remote control

• Do not spill water or other liquids on the remote control.

• Do not drop the remote control.

• Do not leave or store the remote control in the following types of conditions:

– high humidity or temperature such as near a heater,

stove or bath; – dusty places; or – in places subject to extremely low temperatures.

DIGITAL

SURROUND

–+–

Approximately 6 m (20 feet)

Front Panel Display

CONTROLS AND FUNCTIONS

1 234 wq87

DIGITAL

PRO LOGIC

DSP

6.1/ES PCM

VIRTUAL

ASPB

DTS MOVIE THEATER 1 2 DOLBY DIGITAL PRO LOGIC ENTERTAINMENT

PTY HOLD EON STEREO AUTO NEWS INFO AFFAIRS SPORT

MEMORY TUNED

uyre t

1 t indicator

Lights up when the built-in DTS decoder is on.

2 VIRTUAL indicator

Lights up when using Virtual CINEMA DSP (see page 29).

3 g and o indicators

Light up according to the type of Dolby signals this unit is reproducing. “ g ” lights up when the builtin Dolby Digital decoder is on. “ o ” lights up when the built-in Dolby Pro Logic decoder is on.

4 x indicator

Lights up when you select a DSP program.

5 DSP program indicators

The name of the selected DSP program lights up when the ENTERTAINMENT, MOVIE THEATER 1, MOVIE THEATER 2 or q/DTS SURROUND DSP program is selected.

6 PTY HOLD indicator

Lights up while searching for stations in the PTY SEEK mode.

7 RDS mode indicators

The name(s) of the RDS data offered by the currently received RDS station light(s) up. Illumination of the red indicator next to the RDS data name shows that the corresponding RDS mode is now selected.

8 EON indicator

Lights up when an RDS station that offers the EON data service is being received.

9 STEREO indicator

Lights up when the unit is receiving a strong signal for an FM stereo broadcast while the “AUTO” indicator is lit.

0 AUTO indicator

Shows that this unit is in the automatic tuning mode.

09 5

PTY

SLEEP

VOLUME

dB ms

D-TV/LD

CBL/SAT

VCR 1

VCR2/DVR

V-AUX

apio

q VOLUME level indicator

Indicates the volume level.

w Input source indicator

Shows the current input source with the arrow-shaped cursor.

e c indicator

Lights up when the built-in Dolby Digital Matrix 6.1 or DTS ES decoder is on.

r v indicator

Lights up when this unit is reproducing PCM (pulse code modulation) digital audio signals.

t SP A/B indicator

Lights up according to which set of main speakers is selected. Both indicators light up when both sets of speakers are selected.

y Headphones indicator

Lights up when headphones are connected.

u Multi-information display

Shows the current DSP program name and other information when adjusting or changing settings.

i MEMORY indicator

Flashes to show a station can be stored.

o Program type name indicators

The name of the selected program type lights up when the “EON” indicator lights up.

p TUNED indicator

Lights up when this unit tunes in to a station.

a SLEEP indicator

Lights up while the sleep timer is on.

DVD MD/TAPE CD-R TUNER CD PHONO

INTRODUCTION PREPARATION

OPERAIONT

BASIC

OPERATION

ADVANCED

INFORMATION

ADDITIONAL

APPENDIX

English

CONTROLS AND FUNCTIONS

Rear Panel

DIGITAL OUTPUT AUDIO AUDIO VIDEO

TUNER

MD/ TAPE

ANT

CD-R

GND

OPTICAL

CD-R

ANT

DVD

GND

D-TV

/LD

OPTICAL COAXIAL

CBL /SAT

DIGITAL INPUT 6CH INPUT

L R L

(PLAY)

MD/TAPE

OUT

(REC)

(PLAY)

CD-R

UNBAL.

OUT

(REC)

PHONO

MAIN

SURROUND

SUB

WOOFER

CENTER

S VIDEO VIDEO COMPONENT

DVD

D-TV

/LD

CBL /SAT

VCR 1

OUT

VCR 2

/DVR

OUT

MONITOR

OUT

S VIDEO VIDEO

As this terminal is used for an examination in the factory, do not connect any equipment to this

terminal.

1 DIGITAL INPUT jacks

2 DIGITAL OUTPUT jacks

3 Antenna input terminals

See page 30 for connection information.

4 Audio component jacks

See pages 12 and 13 for connection information.

5 Video component jacks

See pages 14 and 15 for connection information.

6 Speaker terminals

See pages 16 and 17 for connection information.

DVD

D-TV/LD

MONITOR OUT

PR/

PR/ C

PR/

MAIN

CENTER

R L

(SURROUND)

REAR

SPEAKERS OUTPUT

–

R L

–

– –

CENTER

REAR

MAIN

SUB

WOOFER

(SURROUND)

IMPEDANCE SELECTOR

SET BEFORE POWER ON

MAIN A OR B: 4

A + B: 8

CENTER

: 6 : 6

REAR

876

MIN. /SPEAKER MIN. /SPEAKER MIN. /SPEAKER MIN. /SPEAKER

MAINS

100W MAX. TOTAL

MAIN A OR B: 8

A + B:16 CENTER REAR

AC OUTLETS

SWITCHED

MIN. /SPEAKER MIN. /SPEAKER

: 8

MIN. /SPEAKER

: 8

MIN. /SPEAKER

(Europe model)

8 AC power cord

Connect to a power outlet.

9 AC OUTLET(S)

Use these outlets to supply power to your other A/V components (see page 19).

0 6CH INPUT jacks

See pages 13 and 18 for connection information.

q IMPEDANCE SELECTOR switch

Use this switch to match the amplifier output to your speaker impedance. Set this unit in the standby mode before you change the setting of this switch (see page 19).

7 OUTPUT jacks

See page 18 for connection information.

PREPARATION

Speakers to Be Used

SPEAKER SETUP

INTRODUCTION

Speaker Placement

This unit has been designed to provide the best soundfield quality with a 5-speaker system, using left and right main speakers, left and right rear speakers, and a center speaker. If you use different brands of speakers (with different tonal qualities) in your system, the tone of a moving human voice and other types of sound may not shift smoothly. We recommend that you use speakers from the same manufacturer or speakers with the same tonal quality.

The main speakers are used for the main source sound plus the effect sounds. They will probably be the speakers from your present stereo system. The rear speakers are used for the effect and surround sounds, and the center speaker is for the center sounds (dialog, vocals, etc.). If for some reason it is not practical to use a center speaker, you can do without it. Best results, however, are obtained with the full system.

The main speakers should be high-performance models and have enough power-handling capacity to accept the maximum output of your audio system. The other speakers do not have to be equal to the main speakers. For precise sound localization, however, it is ideal to use high-performance models that can reproduce sounds over the full range for the center speaker and the rear speakers.

■ Use of a subwoofer expands your sound field

It is also possible to further expand your system with the addition of a subwoofer. The use of a subwoofer is effective not only for reinforcing bass frequencies from any or all channels, but also for reproducing the LFE (low-frequency effect) channel with high fidelity when the Dolby Digital signal or the DTS signal is played back. The YAMAHA Active Servo Processing Subwoofer System is ideal for natural and lively bass reproduction.

Refer to the following diagram when you place the speakers.

Main speaker (L)

Center speaker

Main speaker (R)

Rear speaker (R)

Subwoofer

1.8 m

Rear speaker (L)

■ Main speakers

Place the left and right main speakers an equal distance from the ideal listening position. The distance of each speaker from each side of the video monitor should be the same.

■ Rear speakers

Place these speakers behind your listening position, facing slightly inwards, nearly 1.8 m (approx. 6 feet) above the floor.

■ Center speaker

Align the front face of the center speaker with the front face of your video monitor. Place the speaker as close to the monitor as possible, such as directly over or under the monitor and centrally between the main speakers.

Note

• If the center speaker is not used, the center channel sound will be heard from the left and right main speakers. In this case, “1A CENTER SP” on the SET MENU is set to NONE (see page 41 for details).

PREPARATION

BASIC OPERA-

TION

OPERATION

ADVANCED

INFORMATION

ADDITIONAL

■ Subwoofer

The position of the subwoofer is not so critical, because low bass sounds are not highly directional. But it is better to place the subwoofer near the main speakers. Turn it slightly toward the center of the room to reduce the wall reflections.

CAUTION

Some types of speakers interfere with a video monitor. If this problem occurs, move the speakers away from the monitor. If you cannot avoid installing the center speaker or subwoofer near the video monitor, use a magnetically shielded speaker.

APPENDIX

English

CONNECTIONS

Before Connecting Components

CAUTION

Never connect this unit and other components to mains power until all connections between components have been completed.

• Be sure all connections are made correctly, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Some components require different connection methods and have different jack names. Refer to the operation instructions for each component to be connected to this unit.

• When you connect other YAMAHA audio components (such as a tape deck, MD recorder and CD player or changer), connect them to the jack with the same number labels as !, #, $ etc. YAMAHA applies this labeling system to all its products.

• After you have completed all connections, check them again to make sure they are correct.

Connecting Audio Components

■ Connecting to digital jacks

This unit has digital jacks for direct transmission of digital signals through either coaxial or fiber optic cables. You can use the digital jacks to input PCM, Dolby Digital and DTS bitstreams. When you connect components to both the COAXIAL and OPTICAL jacks, priority is given to the input signals from the COAXIAL jack. All digital input jacks are acceptable for 96-kHz sampling digital signals (see page 25 for details).

• You can designate the input for each digital jack according to

your component by using “7 I/O ASSIGNMENT” on the SET MENU (see page 44 for details).

About the dust protection cap

Pull out the cap from the optical jack before you connect the fiber optic cable. Do not discard the cap. When you are not using the optical jack, be sure to put the cap back in place. This cap protects the jack from dust.

Note

• The OPTICAL jacks on this unit conform to the EIA standard.

If you use a fiber optic cable that does not conform to this standard, this unit may not function properly.

■ Connecting a turntable

PHONO jacks are for connecting a turntable with an MM or high-output MC cartridge. If you have a turntable with a low-output MC cartridge, use an inline boosting transformer or MC-head amplifier when connecting to these jacks.

• The GND terminal does not electrically ground the turntable. It

simply reduces noise in the signal. In some cases, you may hear less noise if you do not connect to the GND terminal.

■ Connecting a CD player

• The COAXIAL CD and OPTICAL CD jacks are available for a CD player which has coaxial or optical digital output jacks.

• When you connect a CD player to both the COAXIAL CD and OPTICAL CD jacks, priority is given to the input signals from the COAXIAL CD jack.

■ Connecting an MD recorder, tape

deck or CD recorder

• Only digital signals input from a source such as a CD or DVD are output from the DIGITAL OUTPUT jacks.

• When you connect your recording component to both the analog and digital input and output jacks, the priority is given to the digital signal.

• You can connect an MD recorder to any digital input jack by using “7 I/O ASSIGNMENT” on the SET MENU (see page 44).

Notes

• When you connect a recording component to this unit, keep its power on while using this unit. If the power is off, this unit may distort the sound from other components.

• When you record from a source component connected to this unit while this unit is set in the standby mode, the recorded sound may be distorted. To avoid this problem, turn on this unit.

OPTICAL INPUT

MD recorder or

tape deck

OPTICAL INPUT

CD recorder

CONNECTIONS

OPTICAL OUTPUT

INTRODUCTION

OPTICAL OUTPUT

CD player

COAXIAL OUTPUT

INPUT OUTPUT INPUTOUTPUT

OUTPUT

(Europe model)

GND

OUTPUT

DIGITAL OUTPUT AUDIO AUDIO VIDEO

MD/ TAPE

ANT

CD-R

GND

OPTICAL

CD-R

ANT

DVD

GND

D-TV

/LD

OPTICAL COAXIAL

CBL /SAT

DIGITAL INPUT 6CH INPUT

L R

TUNER

UNBAL.

(PLAY)

MD/TAPE

OUT

(REC)

(PLAY)

CD-R

OUT

(REC)

PHONO

MAIN

SURROUND

CENTER

L R L

SUB

WOOFER

SUBWOOFER OUTPUT

CENTER OUTPUT

S VIDEO VIDEO COMPONENT

DVD

D-TV

/LD

CBL /SAT

VCR 1

OUT

VCR 2

/DVR

OUT

MONITOR

OUT

S VIDEO VIDEO

L R

External decoder

DVD

P C

PR/

D-TV/LD

B/ B

PR/ C

MONITOR OUT

PR/ C

SURROUND OUTPUT

See page 18.

L R

MAIN OUTPUT

PREPARATION

BASIC OPERA-

TION

OPERATION

ADVANCED

INFORMATION

ADDITIONAL

Turntable

indicates signal direction

indicates left analog cables

indicates right analog cables

indicates optical cables

indicates coaxial cables

APPENDIX

English

CONNECTIONS

Connecting Video Components

■ About the video jacks

There are three types of video jacks. Video signals input through the VIDEO jacks are the conventional composit video signals. Video signals input through the S VIDEO jacks are separated into luminance (Y) and color (C) video signals. The S-video signals achieve high-quality color reproduction. Video signals input through the COMPONENT VIDEO jacks are separated into luminance (Y) and color difference (P into three for each signal. The description of the component video jacks may be different depending on the component (e.g. Y, C

, CR/Y, PB, PR/Y, B-Y, R-Y etc.). Component video signals provide the best quality in picture reproduction.

If your video component has an S-video output or component video output, you can connect it to this unit. Connect the S-video signal output jack on your video component to the S VIDEO jack or connect the component signal output jacks on your video component to the COMPONENT VIDEO jacks.

VIDEO jack (composite)

S VIDEO jack COMPONENT VIDEO

PB/ CB

PR/ CR

jacks

Notes

• Use a commercially available S-video cable when connecting to the S VIDEO jack, and commercially available video cables when connecting to the COMPONENT VIDEO jacks.

• When you are using the COMPONENT VIDEO jacks, check the details in the owner’s manual that came with the component being connected.

, PR/CR) video signals. The jacks are also separated

B/CB

• Each type of video jack works independently. Signals input through the composite video, S-video and component jacks are output through the corresponding composite video, S-video, and component jacks, respectively.

• If you make S-video connections to this unit, it is not necessary to make composite video connections. If both types of connections are made, this unit gives priority to the S-video signal.

• You can designate the input for the COMPONENT VIDEO A and B jacks according to your component by using “7 I/O ASSIGNMENT” on the SET MENU (see page 44 for details).

■ Video monitor with a 21-pin connector

Make a connection as shown on page 15 with a commercially available SCART-plug connector cable.

■ VIDEO AUX jacks (on the front panel)

S VIDEO VIDEO

L AUDIO R OPTICAL

VIDEO AUX

These jacks are used to connect any video input source such as a game console to this unit.

OPTICAL OUT

AUDIO OUT R

AUDIO OUT L

VIDEO OUT

S VIDEO OUT

Game console

Note

• If your LD player has an Dolby Digital RF signal output jack, connect it to this unit through an RF demodulator (separately purchased).

RF OUTPUT

LD player

COMPONENT OUTPUT

AUDIO OUTPUT

OPTICAL OUTPUT

TV/digital TV or

LD player

OPTICAL OUTPUT

DVD player

CONNECTIONS

INTRODUCTION

COMPONENT OUTPUT

RF INPUT

RF demodulator

S VIDEO OUTPUT

AUDIO OUTPUT

DIGITAL OUTPUT AUDIO AUDIO VIDEO

OUTPUT

TUNER

MD/ TAPE

ANT

CD-R

GND

OPTICAL

CD-R

ANT

DVD

GND

D-TV

/LD

OPTICAL COAXIAL

CBL /SAT

DIGITAL INPUT 6CH INPUT

UNBAL.

(PLAY)

MD/TAPE

OUT

(REC)

(PLAY)

CD-R

OUT

(REC)

PHONO

MAIN

SURROUND

CENTER

WOOFER

L R L

SUB

VIDEO

S VIDEO VIDEO COMPONENT

DVD

D-TV

/LD

CBL

/SAT

VCR 1

OUT

VCR 2

/DVR

OUT

MONITOR

OUT

S VIDEO VIDEO

S S

S VIDEO OUTPUT

VIDEO OUTPUT

Cable TV or

Satellite tuner

COAXIAL OUTPUT

S VIDEO OUTPUT

AUDIO INPUT

AUDIO OUTPUT

DVD

P C

PR/ C

D-TV/LD

P C

PR/

MONITOR OUT

PR/ C

S VIDEO INPUT

VIDEO OUTPUT

VCR 1 or VCR 2/

DVR (digital

video recorder)

VIDEO

OUTPUT

(Europe model)

*1 You can connect the Dolby

Digital RF signal output of your LD player to the COAXIAL jack by using “7 I/O ASSIGNMENT” on the SET MENU (see page 44).

VIDEO INPUT

PREPARATION

BASIC OPERA-

TION

OPERATION

ADVANCED

INFORMATION

ADDITIONAL

APPENDIX

indicates signal direction

indicates left analog cables

indicates right analog cables

indicates optical cables

indicates coaxial cables

indicates video cables

indicates S-video cables

No connection

SCART-plug

VIDEO INPUT

S VIDEO INPUT

English

COMPONENT INPUT

Video monitor

CONNECTIONS

Connecting the Speakers

Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be unnatural and lack bass.

CAUTION

• Use speakers with the specified impedance shown on the rear panel of this unit.

• Do not let the bare speaker wires touch each other and do not let them touch any metal part of this unit. This could damage the unit and/or speakers.

If necessary, use the SET MENU to change the speaker mode settings according to the number and size of the speakers in your configuration after you finish connecting your speakers.

■ Speaker cables

A speaker cord is actually a pair of insulated cables

10 mm (3/8”)

running side by side. One of the cables is colored or shaped differently, perhaps with a stripe, groove or ridge.

1 Remove approx. 10 mm (3/8”) of insulation

from each of the speaker cables.

2 Twist the exposed wires of the cable

together to prevent short circuits.

■ Connecting to the SPEAKERS terminals

Red: positive (+) Black: negative (–)

1 Unscrew the knob. 2 Insert one bare wire into the hole in the side

of each terminal.

3 Tighten the knob to secure the wire.

■ MAIN SPEAKERS terminals

One or two speaker systems can be connected to these terminals. If you use only one speaker system, connect it to either of the MAIN A or B terminals.

■ REAR SPEAKERS terminals

A rear speaker system can be connected to these terminals.

■ CENTER SPEAKER terminals

A center speaker can be connected to these terminals.

CONNECTIONS

SPEAKERS OUTPUT

MAIN

CENTER

REAR

(SURROUND)

MAIN

CENTER

SUB

WOOFER

R L

–

R L

–

– –

REAR

(SURROUND)

MAIN A OR B: 4

MIN. /SPEAKER

A + B: 8

MIN. /SPEAKER

CENTER

: 6

MIN. /SPEAKER

REAR

: 6

MIN. /SPEAKER

MAIN A OR B: 8

MIN. /SPEAKER

A + B:16

MIN. /SPEAKER

CENTER

: 8

MIN. /SPEAKER

REAR

: 8

MIN. /SPEAKER

IMPEDANCE SELECTOR

SET BEFORE POWER ON

SWITCHED

100W MAX. TOTAL

AC OUTLETS

MAINS

Main speakers A

Right Left

Main speakers B

INTRODUCTION

Right Left

(Europe model)

PREPARATION

BASIC OPERA-

TION

Center speaker Rear speakers

OPERATION

ADVANCED

Subwoofer connection

See “SUBWOOFER jack” on page 18.

Right Left

Subwoofer

system

INFORMATION

ADDITIONAL

APPENDIX

English

CONNECTIONS

Connecting to an External Amplifier

If you want to increase the power output to the speakers, or want to use another amplifier, connect an external amplifier to the OUTPUT jacks as follows.

Note

• When RCA pin plugs are connected to the OUTPUT jacks for output to an external amplifier, it is not necessary to use the corresponding SPEAKERS terminals.

1 MAIN jacks

Main channel line output jacks.

Note

• The signals output through these jacks are affected by the BASS, TREBLE and BASS EXTENSION settings.

R L

CENTER

REAR

OUTPUT

MAIN

WOOFER

(SURROUND)

SUB

Connecting an External Decoder

This unit is equipped with 6 additional input jacks (left and right MAIN, CENTER, left and right SURROUND and SUBWOOFER) for discrete multi-channel input from an external decoder, sound processor or pre-amplifier.

Connect the output jacks on your external decoder to the 6CH INPUT jacks. Be sure to match the left and right outputs to the left and right input jacks for the main and surround channels.

Notes

• When you select 6CH INPUT as the input source, this unit automatically turns off the digital sound field processor, and you cannot listen to DSP programs.

• When you select 6CH INPUT as the input source, changing items 1A to 1E on the SET MENU is not affected.

2 SUBWOOFER jack

When using a subwoofer with built-in amplifier, including the YAMAHA Active Servo Processing Subwoofer System, connect the input jack of the subwoofer system to this jack. Low bass signals distributed from the main, center and/or rear channels are directed to this jack. (The cut-off frequency of this jack is 90 Hz.) The LFE (lowfrequency effect) signals generated when Dolby Digital or DTS is decoded are also directed if they are assigned to this jack.

Notes

• Adjust the volume level of the subwoofer with the control on the subwoofer. The subwoofer volume cannot be adjusted from this unit.

• Depending on the settings of “1 SPEAKER SET”, “10A LFE LEVEL” and “11 DTS LFE LEVEL” on the SET MENU, some signals may not be output from the SUBWOOFER jack.

3 CENTER jack

Center channel line output jack.

4 REAR (SURROUND) jacks

Rear channel line output jacks.

IMPEDANCE SELECTOR Switch

CONNECTIONS

WARNING

Do not change the IMPEDANCE SELECTOR switch setting while the power of this unit is on, otherwise the unit may be damaged. If this unit fails to turn on when STANDBY/ON (or POWER) is pressed, the IMPEDANCE SELECTOR switch may not be fully slid to either position. If so, slide the switch to either position fully when this unit is in the standby mode.

Select the left or right position according to the impedance of the speakers in your system. Be sure to move this switch only when this unit is in the standby mode.

(Europe model)

MAINS

AC OUTLETS

SWITCHED

100W MAX. TOTAL

IMPEDANCE SELECTOR

SET BEFORE POWER ON

MAIN A OR B: 4

MIN. /SPEAKER

MAIN A OR B: 8

A + B: 8 CENTER REAR

MIN. /SPEAKER

: 6

MIN. /SPEAKER

: 6

MIN. /SPEAKER

A + B:16 CENTER REAR

MIN. /SPEAKER MIN. /SPEAKER

: 8

MIN. /SPEAKER

: 8

MIN. /SPEAKER

IMPEDANCE SELECTOR

Switch position

Left

Right

Speaker Impedance level

If you use one set of main speakers, the impedance of each speaker must be 4 Ω or higher.

Main

If you use two sets of main speakers, the impedance of each speaker must be 8 Ω or higher.

Center

Rear

The impedance must be 6 Ω or higher.

The impedance of each speaker must be 6 Ω or higher.

If you use one set of main speakers, the impedance of

Main

each speaker must be 8 Ω or higher.

If you use two sets of main speakers, the impedance of each speaker must be 16 Ω or higher.

Center

Rear

The impedance must be 8 Ω or higher.

The impedance of each speaker must be 8 Ω or higher.

INTRODUCTION

PREPARATION

OPERAIONT

BASIC

OPERATION

ADVANCED

Connecting the Power Supply Cords

After completing all connections, connect the AC power cord to an AC power outlet. Disconnect the AC power cord if you will not use this unit for a long period of time.

■ AC OUTLET(S) (SWITCHED)

Europe model ............................................... 2 OUTLETS

U.K. model ..................................................... 1 OUTLET

Use these outlets to connect the power cords from your components to this unit. The power to the AC OUTLET(S) is controlled by this unit’s STANDBY/ON (or POWER and STANDBY). These outlets will supply power to any connected component whenever this unit is turned on. The maximum power (total power consumption of components) that can be connected to the AC OUTLET(S) is 100 W.

IMPEDANCE SELECTOR

SET BEFORE POWER ON

MAIN A OR B: 4

A + B: 8

CENTER

: 6 : 6

REAR

MIN. /SPEAKER MIN. /SPEAKER MIN. /SPEAKER MIN. /SPEAKER

MAINS

MAIN A OR B: 8

A + B:16 CENTER REAR

SWITCHED

(Europe model)

AC OUTLETS

SWITCHED

100W MAX. TOTAL

MIN. /SPEAKER MIN. /SPEAKER

: 8

MIN. /SPEAKER

: 8

MIN. /SPEAKER

To AC outlet

INFORMATION

ADDITIONAL

APPENDIX

English

ON-SCREEN DISPLAY (OSD)

You can display the operation information for this unit on a video monitor. If you display the SET MENU and DSP program parameter settings on a monitor, it is much easier to see the available options and parameters than it is by reading this information on the front panel display.

• If a video source is being reproduced, the OSD is superimposed over the image.

• The OSD signal is not output to the REC OUT jack, and will not be recorded with any video signal.

• You can set the OSD to turn on (blue background) or off when a video source is not being reproduced (or the source component is turned off) by using “14 DISPLAY SET” on the SET MENU (see page 46).

OSD Modes

You can change the amount of information the OSD shows.

Full display

This mode always shows the DSP program parameter settings on the video monitor (see page 63).

Short display

This mode briefly shows the same contents as the front panel display at the bottom of the screen and then disappears.

Display off

This mode briefly shows the “DISPLAY OFF” message at the bottom of the screen and then disappears. Afterwards, no changes to operations appear on the monitor except those of the ON SCREEN button.

P01 CONCERT HALL

INIT. DLY ROOM SIZE 1.0 LIVENESS

45ms

P01 CONCERT HALL

Selecting the OSD Mode

1 When you turn on the power, the video

monitor and front panel display show the level of the main volume for a few seconds and then switch to show the current DSP program.

2 Press ON SCREEN on the remote control

repeatedly to change the display mode.

The OSD mode changes in the following order: full display, short display, and display off.

Notes

• If you choose a video input source that has a component connected to both the S VIDEO IN and composite VIDEO IN jacks, and both the S VIDEO OUT and composite VIDEO OUT jacks are connected to a video monitor, the video signal is output to both the S VIDEO OUT and VIDEO OUT jacks. However, the OSD is carried only on the S-video signal. If no video signal is input, the OSD is carried on both the S-video and composite video signals.

• If your video monitor is connected only to the COMPONENT VIDEO jacks of this unit, the OSD is not shown. Make sure to connect your video monitor to the COMPONENT VIDEO jacks and either VIDEO or S VIDEO jacks if you want to see the OSD.

• Playing back video software that has an anti-copy signal or video signals with a lot of noise may produce unstable images.

Full display Short display

• When you choose the full display mode, INPUT l / h,

VOLUME and some other types of operation information are displayed at the bottom of the screen in the same format as that for the front panel display.

• The SET MENU and test tone display appear regardless of the OSD mode.

SPEAKER MODE SETTINGS

This unit has 5 SPEAKER SET items on the SET MENU that you must set according to the number of speakers in your configuration and their size. The following table summarizes these SPEAKER SET items, and shows the initial settings as well as other possible settings. If the initial settings are not appropriate for your speaker configuration, change the settings on the SET MENU (see page 39).

Summary of SPEAKER SET Items 1A through 1E

Item Description Initial setting

1A CENTER SP Selects the center channel output mode according to the size of the center speaker.

The possible settings are LRG (large), SML (small) and NONE.

1B MAIN SP Selects the main channel output mode according to the size of the main speakers.

The possible settings are LARGE and SMALL.

1C REAR L/R SP Selects the rear channel output mode according to the size of the rear speakers.

The possible settings are LRG (large), SML (small) and NONE.

1D LFE/BASS OUT Selects a speaker for the LFE signal output and low bass signal.

The possible settings are SWFR (subwoofer), MAIN, and BOTH.

1E MAIN LEVEL Selects the output level for the main channel signal.

The possible settings are Normal and –10 dB.

LRG

LARGE

LRG

BOTH

Normal

INTRODUCTION

PREPARATION

OPERAIONT

BASIC

OPERATION

ADVANCED

INFORMATION

ADDITIONAL

APPENDIX

English

ADJUSTING THE SPEAKER OUTPUT LEVELS

This section explains how to adjust the speaker output levels by using the test tone generator. When this adjustment is made, the output level heard at the listening position will be the same from each speaker. This is important for the best performance of the digital sound field processor, the Dolby Pro Logic decoder, Dolby Digital decoder and DTS decoder.

Note

• Since this unit cannot enter the test mode while headphones are connected to this unit, be sure to unplug the headphones from the PHONES jack when using the test tone.

Before You Begin

INPUT

VOLUME

6CH INPUT

BASS

TREBLE

–

STANDBY

/ON

SPEAKERS

EXTENSION

DIGITAL

PRESET/

PRESET

A/B/C/D/E

TUNING

BASS

PROCESSOR

ON OFF

TUNER

DIRECT

DSP

/TUNING

EDIT

PHONES S VIDEO VIDEO

EFFECT

PROGRAM

SILENT

INPUT MODE

DIGITAL

SURROUND

TUNING

RDS MODE

MEMORY

EON PTY SEEK

FM/AM

MODE

/FREQ

MAN'L/AUTO FM

AUTO/MAN'L MONO

START

MODE

L AUDIO R OPTICAL

VIDEO AUX

1 Press STANDBY/ON to

turn on the power. Turn on the video monitor.

STANDBY

/ON

Using the Test Tone (TEST DOLBY SUR.)

Use the test tone to balance the output levels of the 5 speakers required for a surround sound system. The adjustment of each speaker output level should be made at your listening position with the remote control. After completing the adjustments, use VOLUME +/– at your listening position to check if the adjustments are satisfactory.

2,6

5 4

1 Set the selector dial to the

AMP/TUN (or DSP/TUN) position.

2 Press TEST to output the test tone.

2 Press SPEAKERS A or B

to select the main

SPEAKERS

speakers to be used.

If you are using two sets of the main speakers, press both A and B.

3 Set BASS and TREBLE on the front panel to

the center position and set BASS EXTENSION to OFF.

BASS

–

TREBLE

–

BASS

EXTENSION

ON OFF

PROCESSOR

DIRECT

Set to OFF.

3 Adjust the volume so you can hear the test

tone.

The test tone is heard from the left main speaker, center speaker, right main speaker, right rear speaker and left rear speaker in order. The tone is produced for 2.5 seconds each time.

LEFT

(TEST LEFT)

(TEST CENTER)

LEFT SURROUND

(TEST L SUR.)

RIGHT

(TEST RIGHT)

CENTER

RIGHT SURROUND

(TEST R SUR.)

CONNECTIONSADJUSTING THE SPEAKER OUTPUT LEVELS

The state of the test tone output is also shown on the monitor by an image of the audio listening room. This is convenient for adjusting each speaker level.

TEST DOLBY SUR.

LEFT

• If “1A CENTER SP” on the SET MENU is set to NONE, the center channel sound is automatically output from the left and right main speakers.

Note

• If the test tone cannot be heard, turn down the volume, set the unit in the standby mode and check the speaker connections.

4 Press LEVEL repeatedly

to select the speaker to be adjusted.

• Once you press LEVEL, you can also select the speaker to be adjusted by pressing d. (Pressing u changes the selection in the reverse order.)

• The tonal quality of the center speaker can be adjusted by using “5 CENTER GEQ” on the SET MENU (see page 43).

• You can increase the output levels of the effect speakers (center, left rear and right rear) to +10 dB. If the output level of these speakers is lower than that of the main speakers even after you have increased the output level of these speakers up to +10 dB, set “1E MAIN LEVEL” on the SET MENU to –10 dB (see page 42). This setting decreases the main speaker output level to about one-third of the normal level. After you have set “1E MAIN LEVEL” on the SET MENU to –10 dB, adjust the levels for the center and rear speakers again.

INTRODUCTION

PREPARATION

OPERAIONT

BASIC

5 Press j / i repeatedly to

adjust the output level of the effect speakers so that the output level coming from each speaker is the same.

While adjusting, the test tone is heard from the selected speaker.

6 When the adjustment is complete, press

TEST.

The test tone stops and the current DSP program appears on the front panel display and on the video monitor.

OPERATION

ADVANCED

INFORMATION

ADDITIONAL

APPENDIX

English

BASIC OPERATION

DIGITAL

DTS MOVIE THEATER 1 DOLBY DIGITAL PRO LOGIC ENTERTAINMENT

DSP

PRO LOGIC

VIRTUAL

PTY

HOLD

EON

STEREO

AUTO NEWS INFO AFFAIRS SPORT MEMORY TUNED

ZONE 2

dB ms

SLEEP

BASIC PLAYBACK

When using the remote control, set the selector dial to the AMP/TUN position.

STANDBY

/ON

SPEAKERS

EXTENSION

DIGITAL

PRESET/

PRESET

A/B/C/D/E

TUNING

BASS

PROCESSOR

ON OFF

TUNER

DIRECT

EFFECT

PROGRAM

DSP

MEMORY

FM/AM

/TUNING

EDIT

MAN'L/AUTO FM

PHONES S VIDEO VIDEO

SILENT

TUNING MODE

AUTO/MAN'L MONO

RDS MODE

/FREQ

EON PTY SEEK

L AUDIO R OPTICAL

VIDEO AUX

INPUT MODE

DIGITAL

SURROUND

MODE

START

353

INPUT

VOLUME

BASS

TREBLE

–

1 Press STANDBY/ON (or POWER) to turn on

the power. Turn on the video monitor.

The front panel display and the video monitor show the level of the main volume for a few seconds and then switch to show the current DSP program.

STANDBY

/ON

2 Press SPEAKERS A or B

to select the main speakers to be used.

If you are using two sets of main speakers, press both A and B.

Remote controlFront panel

SPEAKERS

Front panel

3 Press INPUT l / h repeatedly (or press one

of the input selector buttons) to select the input source.

• The current input source is indicated on the front panel display with an arrow.

6CH INPUT

• The current input source name and input mode appear on the front panel display and on the video monitor for a few seconds.

INPUT

Front panel

VIRTUAL

DIGITAL

PRO LOGIC

DSP

6.1/ES PCM

ASPB

DTS MOVIE THEATER 1 DOLBY DIGITAL PRO LOGIC ENTERTAINMENT

PSPS

PTY

HOLD NEWS INFO AFFAIRS SPORT MEMORY TUNED

PTY

RTRT

EON

STEREO

AUTO

Remote control

ZONE 2 SLEEP

Selected input source

Select this: To reproduce the signal from

this component

DVD: DVD player D-TV/LD: TV or digital TV/LD player CBL/SAT: Cable TV/satellite tuner VCR 1: Video cassette deck 1 VCR 2/DVR: Video cassette deck 2/digital

video recorder

V-AUX: Another A/V component

(connected to the VIDEO AUX

jacks on the front panel) PHONO: Turntable CD: CD player TUNER: AM/FM tuner CD-R: CD recorder MD/TAPE: MD recorder/tape deck

VOLUME

DVD MD/TAPE

D-TV/LD

CD-R

CBL/SAT

TUNER

VCR 1

VCR2/DVR

dB ms

V-AUX

PHONO

+ 58 hidden pages

Yamaha Audio RX-V800RDS User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

INTRODUCTION

CONTENTS

FEATURES

GETTING STARTED

CONTROLS AND FUNCTIONS

PREPARATION

SPEAKER SETUP

CONNECTIONS

ON-SCREEN DISPLAY (OSD)

SPEAKER MODE SETTINGS

ADJUSTING THE SPEAKER OUTPUT LEVELS

BASIC OPERATION

BASIC PLAYBACK