Yamaha Audio RX-V395RDS User Manual

R X -V 3 9 5

R X -V 3 9 5 R D S

NATURAL SOUND AV RECEIVER

AMPLI-TUNER AUDIO-VIDEO

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

SUPPLIED ACCESSORIES ● After unpacking, check that the following parts are included. ACCESSORIES FOURNIS ● Après le déballage, vérifier que les pièces suivantes sont incluses. MITGELIEFERTE ZUBEHÖRTEILE ● Nach dem Auspacken überprüfen, ob die folgenden Teile vorhanden sind. MEDFÖLJANDE TILLBEHÖR ● Kontrollera efter det apparaten packats upp att följande delar finns med. ACCESSORI IN DOTAZAIONE ● Verificare che tutte le parti seguenti siano contenute nell’imballaggio dell’apparecchio. ACCESORIOS INCLUIDOS ● Desembalar el aparato y verificar que los siguientes accesorios están en la caja. BIJGELEVERDE ACCESSOIRES ● Controleer na het uitpakken of de volgende onderdelen voorhanden zijn.

● Indoor FM Antenna

● Antenne FM intérieure

● UKW-Innenantenne

● FM inomhusantenn

● Antenna FM interna

● Antena FM interior

● FM Binnenantenne

● AM Loop Antenna

● Cadre-antenne AM

● MW-Rahmenantenne

● AM ramantenn

● Antenna AM ad anello

● Antena de cuadro de AM

● AM Lusantenne

● Remote Control Transmitter

● Emetteur de télécommande

● Fernbedienung

● Fjärrkontroll

● Telecomando

● Transmisor de control remoto

● Afstandbediening

TI ME /

LE VE L

–+

P RO GR AM

V CR

RE C /PA US E

D IR BD IR A

P RE SE T

–+

P OW ER /I

S LEE P

D ELA Y /CE NT ER

/R EA R/S W FR

P RO LO GIC

TV /D B S

D ISC

A/ B/C/ D/ E

V OL UM E

TE S T

EF FE CT

O N/O FF

EN H AN C ED

D VD /LD

2 CH /6 CH

P LAY

TA P E

A /B

TU N ER

P LAY

C D

P HO NO

● 75-ohm/300-ohm antenna adapter <U.K. model only>

● Adaptateur d’antenne 75 ohms/300 ohms <Modèle pour le

Royaume-Uni seulement>

● 75 Ohm/300 Ohm Antennenstecker <nur Großbritannien-

Modell>

● 75 ohm/300 ohm antennadapter <Endast modell för

brittisk>

● Adattatore per antenna da 75 e 300 ohm <Solo modello

per la Gran Bretagna>

● Adaptador de antena de 75 ohmios/300 ohmios <Modelo

para Reino Unido sólo>

● 75 ohm/300 ohm antenne-adapter <Alleen modellen voor

Groot-Brittannië>

● Batteries (size AA, R6, UM-3)

● Piles (taille AA, R6, UM-3)

● Batterien (Größe AA, R6, UM-3)

● Batterier (storlek AA, R6, UM-3)

● Batterie (dimensioni AA, R6, UM-3)

● Pilas (tamaño AA, R6, UM-3)

● Batterijen (maat AA, R6, UM-3)

Thank you for selecting this YAMAHA AV receiver.

FEATURES

English

● 5 Speaker Configuration

(Power Amp. Section) Main: 60W + 60W (8Ω) RMS Output

Power, 0.04% THD, 20–20,000 Hz

Center: 60W (8Ω) RMS Output Power,

0.04% THD, 20–20,000 Hz

Rear: 60W + 60W (8Ω) RMS Output

Power, 0.04% THD, 20–20,000 Hz

● Digital Sound Field Processor

● Dolby Pro Logic Surround Decoder

● Theater-like Sound Experience by the

Combination of Dolby Pro Logic and YAMAHA DSP Technology (CINEMA DSP)

● Automatic Input Balance Control for

Dolby Pro Logic Surround

● Test Tone Generator for Easier Speaker

Balance Adjustment

● 3 Center Channel Modes

(NORMAL/WIDE/PHANTOM)

● Multi-Functions for RDS Broadcast

Reception

● 40-Station Random Access Preset Tuning

● Automatic Preset Tuning

● Preset Station Shifting Capability (Preset

Editing)

● IF Count Direct PLL Synthesizer Tuning

System

● 6-Channel External Decoder Input for

Dolby Digital, DTS, and Other Future Formats

● Video Signal Input/Output Capability

● SLEEP Timer

● Remote Control Capability

RX-V395RDS only

CONTENTS

SUPPLIED ACCESSORIES............................2

FEA TURES .....................................................3

CAUTION ........................................................4

NOTES ABOUT THE REMOTE CONTROL

TRANSMITTER...............................................5

PROFILE OF THIS UNIT ................................6

SPEAKER SETUP ..........................................7

CONNECTIONS..............................................8

CONTROLS AND THEIR FUNCTIONS ........ 14

SPEAKER BALANCE ADJUSTMENT ..........19

Illustrations in this manual show the RX-V395RDS model. Functions and parts applicable only to the RX-V395RDS are clearly specified.

BASIC OPERATIONS ...................................22

TUNING OPERATIONS ................................26

PRESET TUNING ......................................... 27

RECEIVING RDS STATIONS .......................30

USING DIGITAL SOUND FIELD

PROCESSOR (DSP) .................................... 35

SETTING THE SLEEP TIMER......................39

TROUBLESHOOTING ..................................40

SPECIFICATIONS ........................................41

CAUTION : READ THIS BEFORE OPERATING YOUR UNIT.

1. To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2. Install this unit in a cool, dry, clean place – away from

windows, heat sources, sources of excessive vibration, dust, moisture and cold. Avoid sources of humming (transformers, motors). To prevent fire or electrical shock, do not expose the unit to rain or water.

3. Never open the cabinet. If something drops into the set,

contact your dealer.

4. Do not use force on switches, controls or connection wires.

When moving the unit, first disconnect the power plug and the wires connected to other equipment. Never pull the wires themselves.

5. The openings on the unit cover assure proper ventilation of

the unit. If these openings are obstructed, the temperature inside the unit will rise rapidly. Therefore, avoid placing objects against these openings, and install the unit in a well-ventilated area to prevent fire and damage.

<China, U.K. and Europe models only> Be sure to allow a space of at least 20 cm behind, 20 cm on the both sides and 30 cm above the top panel of the unit to prevent fire and damage.

6. Always set the VOLUME control to “– ∞” before starting

the audio source play. Increase the volume gradually to an appropriate level after playback has been started.

7. Do not attempt to clean the unit with chemical solvents;

this might damage the finish. Use a clean, dry cloth.

8. Be sure to read the “TROUBLESHOOTING” section

regarding common operating errors before concluding that the unit is faulty.

9. When not planning to use this unit for long periods of time

(i.e., vacation, etc.), disconnect the AC power plug from the wall outlet.

IMPORTANT

Please record the serial number of this unit in the space below.

Model: Serial No.: The serial number is located on the rear of the unit.

Retain this Owner’s Manual in a safe place for future reference.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

This unit is not disconnected from the AC power source as long as it is connected to the wall outlet, even if this unit itself is turned off. This state is called the standby mode. In this state, this unit is designed to consume a very small quantity of power.

FREQUENCY STEP switch <China and General models only>

Because the interstation frequency spacing differs in different areas, set the FREQUENCY STEP switch (located on the rear panel) according to the frequency spacing in your area. Before setting this switch, disconnect the AC power plug of this unit from the AC outlet.

For Canadian Customers

To prevent electric shock, match wide blade of plug to wide slot and fully insert.

This Class B digital apparatus complies with CANADIAN ICES-003

10.To prevent lightning damage, disconnect the AC power

plug and antenna cable when there is an electrical storm.

11.Grounding or polarization – Precautions should be taken

so that the grounding or polarization of an appliance is not defeated.

12.Do not connect audio equipment to the AC outlet on the

rear panel if the equipment requires more power than the outlet is rated to provide.

13.Voltage Selector <China and General models only>

The voltage selector on the rear panel of this unit must be set for your local main voltage BEFORE plugging into the AC power supply. Voltages are 110/120/220/240 V AC, 50/60 Hz.

For U.K. customers

Special Instructions for U.K. Model

English

If the socket outlets in the home are not suitable for the plug supplied with this appliance, it should be cut off and an appropriate 3 pin plug fitted. For details, refer to the instructions described on the right.

Note: The plug severed from the mains lead must be destroyed, as a plug with bared flexible cord is hazardous if engaged in a live socket outlet.

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL Brown: LIVE

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. Making sure that neither core is connected to the earth terminal of the three pin plug.

NOTES ABOUT THE REMOTE CONTROL TRANSMITTER

Battery installation

Battery replacement

When you notice a decrease in the operating range of the remote control transmitter, the batteries are weak. Replace both batteries with new ones.

Notes

● Use only AA, R6, UM-3 batteries for replacement.

● Be sure the polarities are correct. (See the illustration inside

the battery compartment.)

● Remove the batteries if the remote control transmitter will

not be used for an extended period of time.

● If batteries leak, dispose of them immediately. Avoid

touching the leaked material or letting it come in contact with clothing, etc. Clean the battery compartment thoroughly before installing new batteries.

Remote control transmitter operation range

–dB

Remote control sensor

Within approximately 6 m (19.7 feet)

30°

Notes

● There should be no large obstacles between the remote

control transmitter and the main unit.

● If the remote control sensor is directly illuminated by strong

lighting (especially an inverter type of fluorescent lamp, etc.), it might cause the remote control transmitter not to work correctly. In this case, reposition the main unit to avoid direct lighting.

30°

PROFILE OF THIS UNIT

You are the proud owner of a Yamaha stereo receiver – an extremely sophisticated audio component. The Digital Sound Field Processor (DSP) built into this unit takes advantage of Yamaha’s undisputed leadership in the field of digital audio processing to bring you a whole new world of listening experiences. Follow the instructions in this manual carefully when setting up your system, and this unit will sonically transform your room into a wide range of listening environments – movie theater, concert hall, and so on. In addition, you get incredible realism from sources encoded with Dolby Surround using the built-in Dolby Pro Logic Surround decoder. Please read this owner’s manual carefully and store it in a safe place for later reference.

Digital Sound Field Processing

What is it that makes live music so good? Today’s advanced sound reproduction technology lets you get extremely close to the sound of a live performance, but chances are you’ll still notice something missing: the acoustic environment of the live concert hall. Extensive research into the exact nature of the sonic reflections that create the ambience of a large hall has made it possible for Yamaha engineers to bring you this same sound in your own listening room, so you’ll feel all the sound of a live concert.

Dolby Pro Logic Surround

This unit employs a Dolby Pro Logic Surround decoder similar to professional Dolby Stereo decoders used in many movie theaters. By using the Dolby Pro Logic Surround decoder, you can experience the dramatic realism and impact of Dolby Surround movie theater sound in your own home. Dolby Pro Logic employs a four channel five speaker system. The Pro Logic Surround system divides the input signal into four levels: the left and right main channels, the center channel (used for dialog), and the rear surround sound channel (used for sound effects, background noise, and other ambient noises). The center channel allows listeners seated in even less-than-ideal positions to hear the dialog originating from the action on the screen while experiencing good stereo imaging. Dolby Surround is encoded on the sound track of pre-recorded video tapes, laser discs, and some TV/cable broadcasts. When you play a source encoded with Dolby Surround on this unit, the Dolby Pro Logic Surround decoder decodes the signal and distributes the surround-sound effects.

Furthermore, our technicians, armed with sophisticated measuring equipment, have even made it possible to capture the acoustics of a variety of venues such as an actual concert hall, theater, etc. to allow you to accurately recreate one of several actual live performance environments, all in your own home.

This Dolby Pro Logic Surround Decoder employs a digital signal processing system. This system improves the stability of sound at each channel and minimizes crosstalk between channels, so that positioning of sounds around the room is more accurate compared with conventional analog signal processing systems. In addition, this unit features a built-in automatic input balance control. This always assures you the best performance without manual adjustment.

Manufactured under license from Dolby Laboratories. “Dolby”, “AC-3”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories.

Dolby Pro Logic Surround + DSP

A Dolby Surround sound system shows its full ability in a large movie theater, because movie sounds are originally designed to be reproduced in a large movie theater using many speakers. It is difficult to create a sound environment similar to that of a movie theater in your listening room, because the room size, materials of inside walls, the number of speakers, etc. of your listening room is much different from those of a movie theater. Yamaha DSP technology made it possible to present you with nearly the same sound experience as that of a large movie theater in your listening room by compensating for lack of presence and dynamics in your listening room with its original digital sound fields combined with Dolby Surround sound field.

The combination of Dolby Pro Logic Surround and DSP is used on the sound field program “

C IN E M A D S P

The YAMAHA “CINEMA DSP” logo indicates these programs are created by the combination of Dolby Pro Logic and YAMAHA DSP technology.

PRO LOGIC ENHANCED”.

SPEAKER SETUP

SPEAKERS TO BE USED

This unit is designed to provide the best sound-field quality with a 5 speaker configuration. The most effective speakers to use with this unit are main speakers, rear speakers and a center speaker. You may omit the center speaker. (Refer to the “4-Speaker Configuration” shown below.) The main speakers are used for the majority of the sound output as well as effect sounds. The rear speakers are used for the effect and surround sounds, and the center speaker is for the center sounds (dialog, etc.) within programs encoded with Dolby Surround. The center speaker needs to be equal in power to the main speakers, though the rear speakers should be slightly lower in power. However, all the speakers should have high enough power handling to accept the maximum output of this unit.

SPEAKER CONFIGURATION

English

5-Speaker Configuration

This configuration is the most effective and recommended one. In this configuration, the center speaker is necessary as well as the rear speakers. If the program DOLBY PRO LOGIC or DOLBY PRO LOGIC ENHANCED is selected, conversations will be output from the center speaker and the ambience will be excellent.

● Set the center channel mode to the “NORMAL” or “WIDE”

position. (For details, refer to page 20.)

Main L

Surround sound

Rear L

Center

Dialogue

Main R Main L

Rear R

SPEAKER PLACEMENT

4-Speaker Configuration

The center speaker is not used in this configuration. If the program DOLBY PRO LOGIC or DOLBY PRO LOGIC ENHANCED is selected, the center sound is output from the left and the right main speakers. However, the sound effect of other programs can be the same as that of the 5-speaker configuration.

● Be sure to set the center channel mode to the “PHANTOM”

position. (For details, refer to page 20.)

Main R

Dialogue

Surround sound

Rear L

Rear R

The recommended 5-speaker configuration requires a pair of main speakers, a center speaker, and a pair of rear speakers (sometimes referred to as surround speakers). When arranging your speakers, refer to the illustration and information below.

Main R

Center

Main L

TV set

Rear R

Rear L

Main: Position the main speakers at equal distances away

from the listening position and at equal distances on either side of the center speaker.

Rear: Position rear speakers directly behind the listening

position at a height of approximately 1.8m (6 feet) up from the floor, facing slightly inward. If the speakers cannot be placed behind the listening position, they may also be placed at the side of the listening position, facing toward the listening position.

Center: Position the center speaker directly in front of the

listening position between the main speakers. (When placing on or near a television, use a magnetically shielded speaker to avoid unwanted interference.)

CONNECTIONS

CONNECTIONS WITH OTHER COMPONENTS

Never plug in this unit and other components until all connections are completed.

When making connections between this unit and other components, be sure all connections are made correctly; that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Also, refer to the owner’s manual for each component to be connected to this unit. * If you have YAMAHA components numbered as 1, 3, 4, etc. on the rear panel, connections can be made easily by connecting

the output (or input) terminals of each component to the same-numbered terminals on this unit.

Turntable

GND

OUTPUT

Monitor TV TV/Satellite tuner Video cassette recorder

VIDEO IN

VIDEO OUT

AUDIO OUT

VIDEO OUT

AUDIO OUT

AUDIO IN

MA IN LEVEL

-10 dB 0dB

RX-V395RDS

only

A N T

G N D

A N T

F M

A M

75 ΩUNBAL.

5 0 k Hz

1 0 0 k Hz

/1 0 k H z

F M / A M

F R EQ U E N C Y

S T E P

6CH DISCRETE IN PUT

M A IN

C E N T E R

S U B

W O O F E R

C D

VIDEO IN

S U R R O U N D

M O N I T O R

O U T

A U D IO S IG N A L

T A P E /M D

IN OU T

(R EC )(P LA Y )

V I D E O S IG N A L

D V D / LD

T V /D B S

D V D / LD T V /D B S

V O L TA G E S E LE C T O R

IM P E D A N C E S E LE C T O R

S ET BE F OR E P O W ER ON

V C R

O U T

(S U R R O U N D )

V C R

O U T

R E A R

A O R B

M A IN

A B

C EN T ER R EA R

M A IN

A O R B

A B:1 6ΩM IN . /S P EA K E R

C EN T ER R EA R

: 4ΩM IN . /S P EA K E R : 8ΩM IN . /S P EA K E R

: 6Ω

M IN . /S P EA K E R

: 6Ω

M IN . /S P EA K E R

: 8ΩM IN . /S P EA K E R

: 8Ω

M IN . /S P EA K E R

: 8Ω

M IN . /S P EA K E R

A C O U T L E T S

I00 W M AX. TOTAL

SWI TCHED

G N D

P H O N O

/ 9 kH z

T o AC outlet

LINE OUT

OUTPUT

LINE IN

VIDEO OUT

AUDIO OUT

CD player

Tape deck, MD recorder, etc.

*1 Ground (GND) terminal (For turntable use)

Connecting the ground wire of the turntable to the GND terminal will normally minimize hum, but in some cases better results may be obtained with the ground wire disconnected.

*2 Voltage Selector <China and General models only>

The voltage selector on the rear panel of this unit must be set for your local main voltage BEFORE plugging into the AC power supply. Voltages are 110/120/220/240 V AC, 50/60 Hz.

*3 MAIN LEVEL Switch RX-V395RDS only

Normally set to “0 dB”. If desired, you can decrease the output level of the MAIN SPEAKERS terminals by 10 dB by setting this switch to “–10 dB”.

LD player, DVD player, etc.

*4 AC OUTLETS (SWITCHED)

<Europe, Canada, U.S.A., China and General models>

.....................................................2 SWITCHED OUTLETS

<U.K. and Australia models>.......... 1 SWITCHED OUTLET

Use these to connect the power cords from your components to this unit. The power to the SWITCHED AC OUTLETS is controlled by this unit’s STANDBY/ON switch or the provided remote

control transmitter’s POWER supply power to any component whenever this unit is turned on. The maximum power (total power consumption of components) that can be connected to the SWITCHED AC OUTLETS is 100 watts.

/I key. These outlets will

Connecting an external decoder for Dolby Digital, DTS and other future formats or a DVD player , etc.

If you have a separate Dolby Digital, DTS or other format decoder, or if you have a DVD player or other component which incorporates a Dolby Digital, DTS, or other format decoder, its 6 channel discrete outputs can be connected to the 6CH DISCRETE INPUT terminals of this unit.

(Example)

6 C H D IS C R E T E O U T P U T

CENTER SURROUN DM AIN

Dolby Digital decoder

English

M A IN

G N D

P H O N O

A N T

G N D

A N T

F M

A M

75 ΩUNBAL.

5 0 k Hz

/ 9 kH z

1 0 0 k Hz

/1 0 k H z

F M / A M

F R EQ U E N C Y

S T E P

S U B

W O O F E R

6CH DISCRETE IN PUT

S U R R O U N D

C E N T E R

S U B

W O O F E R

C D

T A P E /M D

IN OU T

M O N I T O R

D V D / LD

O U T

A U D IO S IG N A L

D V D / LD T V /D B S

(R EC )(P LA Y )

V I D E O S IG N A L

T V /D B S

DIGITAL IN

DIGITAL OUT

V C R

O U T

V C R

O U T

DOLBY DIGITAL RF (AC-3 RF) IN

RF Demodulator

DOLBY DIGITAL RF (AC-3 RF) OUT

VIDEO OUT AUDIO OUT

Notes

● The laserdisc player (or other unit) must be also connected

to the DVD/LD (or TV/DBS) AUDIO SIGNAL input terminals of this unit to play a source encoded with Dolby Pro Logic Surround or in normal stereo (or monaural).

● The discrete signals input to this unit cannot be recorded by

a tape deck, MD recorder or VCR. To record a source played on the laserdisc player (or another unit), it must be connected to the DVD/LD (or TV/DBS) AUDIO/VIDEO SIGNAL input terminals of this unit.

Laserdisc player or other unit with Dolby Digital RF (AC-3 RF) output

● If you made no connection to the SUB WOOFER input

terminal of this unit or you will not use a subwoofer, you should be able to make a setting on the decoder to distribute SUB WOOFER channel signals to the right and left MAIN output terminals.

For details, refer to the owner’s manual supplied with the

decoder.

CONNECTING SPEAKERS

Main speakers A

Right Left

Subwoofer system

O U T P U T

S U B

W O O F ER

S P E A K E R S

M A IN

C E N T E R

C A U T I O N

S E E IN S T R U C T IO N M A N U A L F O R C O R R EC T S ET T IN G .

R E A R

(S U R R O U N D )

Left

IM P E D A N C E S E LE C T O R

S ET BE F OR E P O W ER ON

A O R B

: 4ΩM IN . /S P EA K E R

M A IN

A B

: 8ΩM IN . /S P EA K E R

C EN T ER

: 6Ω

M IN . /S P EA K E R

: 6Ω

M IN . /S P EA K E R

R EA R

M A IN

A O R B

: 8ΩM IN . /S P EA K E R

A B:1 6ΩM IN . /S P EA K E R

: 8Ω

M IN . /S P EA K E R

C EN T ER R EA R

: 8Ω

M IN . /S P EA K E R

Main speakers B

Right

Center speaker

Note

Use speakers with the specified impedance shown on the rear of this unit.

Note on main speaker connections:

One or two speaker systems can be connected to this unit. If you use only one speaker system, connect it to either the

SPEAKERS A or B terminals.

Note on subwoofer connection:

You may wish to add a subwoofer to reinforce low frequencies or to output low bass sound from the subwoofer channel when reproducing discrete signals. Connect the SUBWOOFER OUTPUT terminal of this unit to the input terminal of the subwoofer amplifier, and connect the speaker terminals of the subwoofer amplifier to the subwoofer. With some subwoofers, including the Yamaha Active Servo Processing Subwoofer System, the amplifier and subwoofer are in the same unit.

Right Left

Rear speakers

How to Connect:

Connect the SPEAKERS terminals to your speakers with wire of the proper gauge, cut as short as possible. If the connections are faulty, no sound will be heard from the speakers. Make sure that the polarity of the speaker wires is correct, that is the + and – markings are observed. If these wires are reversed, the sound will be unnatural and lack bass.

Caution Do not let the bare speaker wires touch each other or any metal part of this unit. This could damage this unit and/or speakers.

English

To connect to the MAIN SPEAKERS terminals

Red: positive (+) Black: negative (–)

1 Unscrew the knob.

To connect to the REAR and CENTER SPEAKERS terminals

Red: positive (+) Black: negative (–)

2 Insert the bare wire.

[Remove approx. 5mm (1/4”) insulation from the speaker wires.]

3 Tighten the knob and

secure the wire.

1 Press the tab.

2 Insert the bare wire.

[Remove approx. 5mm (1/4”) insulation from the speaker wires.]

3 Release the tab and

secure the wire.

<U.S.A., Canada, Australia, China and General models only>

Banana Plug connections are also possible. Simply insert the Banana Plug connector into the corresponding terminal.

SUBWOOFER OUTPUT terminal

O U T P U T

S U B

W O O F E R

This terminal is for connecting to the input terminal of an amplifier driving a subwoofer. This terminal outputs low frequencies from the main and center channels. (The cut-off frequency of signals output from this terminal is 150 Hz.) When 6 channel discrete signals are input to this unit and are selected as the input source, this terminal outputs signals from the subwoofer channel.

IMPEDANCE SELECTOR switch

Be sure to switch this only when the power to this unit is not on. Select the position whose requirements your speaker system meets.

WARNING Do not change the IMPEDANCE SELECTOR switch setting while the power to this unit is on, otherwise this unit may be damaged.

IF THIS UNIT FAILS TO TURN ON WHEN THE STANDBY/ ON SWITCH IS PRESSED, the IMPEDANCE SELECTOR switch may not be set to either end closely. If so, set the switch to either end closely.

V O L TA G E S E LE C T O R

IM P E D A N C E S E LE C T O R

S ET BE F O RE P O W ER O N

A O R B

: 4ΩM IN . /S P EA K E R

M A IN

A B

: 8ΩM IN . /S P EA K E R

C EN T ER

: 6Ω

M IN . /S P EA K E R

: 6Ω

M IN . /S P EA K E R

R EA R

M A IN

A O R B

: 8ΩM IN . /S P EA K E R

A B:1 6ΩM IN . /S P EA K E R

: 8Ω

M IN . /S P EA K E R

C EN T ER R EA R

: 8Ω

M IN . /S P EA K E R

A C O U T L E T S

(Left position)

Main: If you use one pair of main speakers, the impedance

of each speaker must be 4Ω or higher. If you use two pairs of main speakers, the impedance of each speaker must be 8Ω or higher.

Center: The impedance of the speaker must be 6Ω or higher. Rear: The impedance of each speaker must be 6Ω or

higher.

(Right position)

Main: <Except for Canada model>

If you use one pair of main speakers, the impedance of each speaker must be 8Ω or higher. If you use two pairs of main speakers, the impedance of each speaker must be 16Ω or higher. <Canada model only> The impedance of each speaker must be 8Ω or higher.

Center: The impedance of the speaker must be 8Ω or higher. Rear: The impedance of each speaker must be 8Ω or

higher.

I00 W M AX. TOTAL

SWI TCHED

IMPEDANCE SELECTOR

ANTENNA CONNECTIONS

● Each antenna should be connected to the designated terminals correctly, referring to the following diagram.

● Both AM and FM indoor antennas are included with this unit. In general, these antennas will probably provide sufficient signal

strength. Nevertheless, a properly installed outdoor antenna will give clearer reception than an indoor one. If you experience poor reception quality, an outdoor antenna may result in improvement.

English

Outdoor FM antenna

75-ohm/300-ohm antenna adapter

75-ohm coaxial cable

75-ohm/300-ohm antenna adapter

300-ohm feeder

Indoor FM antenna (included)

Outdoor AM antenna

AM loop antenna

75 Ω

UNBAL.

F M

A N T

G N D

A M

A N T

(included)

Ground

Connecting the AM loop antenna

12 3

Orient so that the best reception is obtained.

* The AM loop antenna should be placed apart from the main unit. The antenna may be hung on a wall. * The AM loop antenna should be kept connected, even if an outdoor AM antenna is connected to this unit.

GND terminal

For maximum safety and minimum interference, connect the GND terminal to a good earth ground. A good earth ground is a metal stake driven into moist earth.

Notes

● When connecting the indoor FM

antenna, insert its connector into the FM ANT terminal firmly.

● If you need an outdoor

FM antenna to improve FM reception quality, either 300-ohm feeder or coaxial cable

may be used. In locations troubled by electrical interference, coaxial cable is preferable.

+ 30 hidden pages