Yamaha Audio RX-385RDS User Manual

Page 1
RX-485 RDS/385 /385 RDS
Natural Sound Stereo Receiver
Natural Sound Stereoreceiver
Natural Sound Stereoreceiver
Ricevitore stereo a suono naturale
Receptor estéreo de Sonido Natural
Natural Sound Stereo Ontvanger
OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
BRUKSANVISNING
MANUALE DI ISTRUZIONI
MANUAL DE INSTRUCCIONES
GEBRUIKSAANWIJZING
Page 2
SUPPLIED ACCESSORIES ACCESSOIRES FOURNIS MITGELIEFERTE ZUBEHÖRTEILE MEDFÖLJANDE TILLBEHÖR ACCESSORI IN DOTAZIONE ACCESORIOS INCLUIDOS BIJGELEVERDE ACCESSOIRES
After unpacking, check that the following parts are contained.
Après le déballage, vérifier que les pièces suivantes sont incluses.
Nach dem Auspacken überprüfen, ob die folgenden Teile vorhanden sind.
Kontrollera effer det apparaten packats upp att följande delar finns med.
Verificare che tutte le parti seguenti siano contenute nell’imballaggio dell’apparecchio.
Desembale el aparato y verifique que los siguientes accesorios están en la caja.
Controleer na het uitpakken of de volgende onderdelen voorhanden zijn.
Indoor FM Antenna
Antenne FM intérieure
UKW-Innenantenne
FM inomhusantenn
Antenna FM per interni
Antena FM interior
FM Binnenantenne
AM Loop Antenna
Antenne AM à boucle
MW-Rahmenantenne
AM ramantenn
Antenna AM ad anello
Antena de cuadro de AM
AM Lusantenne
Remote Control Transmitter
Emetteur de télécommande
Fernbedienungsgeber
Fjärrkontrollsändare
Telecomando
Transmisor del control remoto
Afstandbediening
RX-485 RDS
Batteries (size AA, R6, UM-3)
Piles (taille AA, R6, UM-3)
Batterien (größ AA, R6, UM-3)
Batterier (storlek AA, R6, UM-3)
Batterie (dimensioni AA, R6, UM-3)
Pilas (tamaño AA, R6, UM-3)
Batterijen (maat AA, R6, UM-3)
RX-385, RX-385 RDS
This product complies with the radio frequency interference requirements of the Council Directive 82/499/EEC and/or 87/308/EEC.
Cet appareil est conforme aux prescriptions de la directive communautaire 87/308/CEE. Diese Geräte entsprechen der EG-Richtlinie 82/499/EWG und/oder 87/308/EWG. Dette apparat overholder det gaeldende EF-direktiv vedrørende radiostøj. Questo apparecchio è conforme al D.M.13 aprile 1989 (Direttiva CEE/87/308) sulla soppressione dei radiodisturbi. Este producto está de acuerdo con los requisitos sobre interferencias de radio frecuencia fijados por el Consejo Directivo
87/308 CEE. Dit product voldoet aan de EEG normen betreffende radio-frekwentie storingen 82/499/EEG en/of 87/308/EEG.
2
Page 3

FEATURES

Thank you for selecting this YAMAHA stereo receiver.

English

RX-485 RDS
65W +65W (8) RMS Output Power,
0.04% THD, 20 – 20,000 Hz
RX-385 and RX-385 RDS
40W +40W (8) RMS Output Power,
0.04% THD, 20 – 20,000 Hz
High Dynamic Power, Low Impedance Drive Capability
Continuously Variable Loudness Control
40-Station Random Preset Tuning
Automatic Preset Tuning
Preset Station Shifting Capability
CONTENTS
IF Count Direct PLL Synthesizer Tuning System
Remote Control Capability
RX-485 RDS and RX-385 RDS only
Multi-Functions for RDS Broadcast Reception
RX-485 RDS only
Pure Direct Switch to Reproduce the Purest Source Sound
Supplied Accessories ......................................2
Caution ............................................................4
Remote Control Transmitter ..........................21
Notes about the Remote Control
Transmitter ....................................................22
Connections ....................................................5
Troubleshooting .............................................23
Operations .......................................................9
Specifications ................................................24
Tuning Operations .........................................12
Preset tuning .................................................13
Receiving RDS Stations
RX-485 RDS and RX-385 RDS only ..........16
How to Use This Manual
This manual describes three YAMAHA receivers, RX-385, RX-385 RDS and RX-485 RDS. There are some differences between those three models. Especially, RX-385 RDS and RX-485 RDS contain the functions for receiving special data on RDS network stations. RX-385, on the other hand, is a receiver with a usual FM/AM tuning function. Several places in the manual refer to differences in features between the three models. Be sure to follow the procedure for the model you are using. * RDS is a data transmitting service system in network which is employed by FM stations. RDS stations are increasing in many
countries (especially in Europe).
3
Page 4
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1. To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2. Install this unit in a cool, dry, clean place – away from windows,
heat sources, sources of excessive vibration, dust, moisture and cold. Avoid sources of humming (transformers, motors). To prevent fire or electrical shock, do not expose the unit to rain or water.
3. Never open the cabinet. If something drops into the set, contact
your dealer.
4. Do not use force on switches, controls or connection wires. When
moving the unit, first disconnect the power plug and the wires connected to other equipment. Never pull the wires themselves.
5. The openings on the cabinet assure proper ventilation of the unit.
If these openings are obstructed, the temperature inside the cabinet will rise rapidly and eventually damage the circuits. Therefore, avoid placing objects against these openings and do not install the unit where the flow of air through the ventilation openings could be impeded.
6. Always set the VOLUME control to “–
source play. Increase the volume gradually to an appropriate level after playback has been started.
” before starting the audio
7. Do not attempt to clean the unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
8. Be sure to read the “TROUBLESHOOTING” section regarding
common operating errors before concluding that the unit is faulty.
9. When not planning to use this unit for long periods of time (ie.,
vacation, etc.), disconnect the AC power plug from the wall outlet.
10.To prevent lightning damage, disconnect the AC power plug and
disconnect the antenna cable when there is an electrical storm.
IMPORTANT
Please record the serial number of this unit in the space below. Serial No.: The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future reference.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
CAUTION (FOR CANADA MODEL)
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT AND FULLY INSERT.
FOR CANADIAN CUSTOMER
THIS DIGITAL APPARATUS DOES NOT EXCEED THE “CLASS B” LIMITS FOR RADIO NOISE EMISSIONS FROM DIGITAL APPARATUS SET OUT IN THE RADIO INTERFERENCE REGULATION OF THE CANADIAN DEPARTMENT OF COMMUNICATIONS.
The apparatus is not disconnected from the AC power source as long as it is connected to the wall outlet, even if the apparatus itself is turned off.
For U.K. customers
If the socket outlets in the home are not suitable for the plug supplied with this appliance, it should be cut off and an appropriate 3 pin plug fitted. For details, refer to the instructions described below. Note: The plug severed from the mains lead must be destroyed, as a plug with bared flexible cord is hazardous if engaged in a live socket outlet.
SPECIAL INSTRUCTIONS FOR U.K. MODEL
11.Grounding or polarization – Precautions should be taken so that
the grounding or polarization of an appliance is not defeated.
12.AC outlet
Do not connect audio equipment to the AC outlet on the rear panel if that equipment requires more power than the outlet is rated to provide.
13.Voltage Selector (General Model only)
The voltage selector on the rear panel of this unit must be set for your local main voltage BEFORE plugging into the AC main supply. Voltages are 110/120/220/240V AC, 50/60 Hz.
IMPORTANT:
The wire in the mains lead are coloured in accordance with the following code:
Blue: NEUTRAL Brown: LIVE
The colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug. Proceed as follows: the wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. Making sure that neither core is connected to the earth terminal of the three pin plug.
FREQUENCY STEP switch (General Model only)
Because the interstation frequency spacing differs in different areas, set the FREQUENCY STEP switch (located at the rear) according to the frequency spacing in your area. Before setting this switch, disconnect the AC power plug of this unit from the AC outlet.
4
Page 5

CONNECTIONS

75
UNBAL
PHONO CD AUX
FM
ANT
GND
AM ANT
TAPE
PB
300-ohm feeder
75-ohm coaxial cable
75-ohm/300-ohm antenna adapter
Ground
Outdoor FM antenna
Indoor FM antenna (included)
Outdoor AM antenna
AM loop antenna (included)
ANTENNA CONNECTIONS
Each antenna should be connected to the designated terminals correctly, referring to the following figure.
Both AM and FM indoor antennas are included with this unit. In general, these antennas will probably provide sufficient signal strength. Nevertheless, a properly installed outdoor antenna will give clearer reception than an indoor one. If you experience poor reception quality, an outdoor antenna may result in improvement.
English
Connecting the AM loop antenna
* The AM loop antenna should be placed apart from the main unit. The antenna may be hung on a wall. * The AM loop antenna should be kept connected, even if an outdoor AM antenna is connected to this unit.
GND terminal
For maximum safety and minimum interference, connect the GND terminal to a good earth ground. A good earth ground is a metal stake driven into moist earth.
Notes
When connecting the indoor FM antenna, make sure that the grooved part of the connector hole is facing downward.
If you need an outdoor FM antenna to improve FM reception quality, either 300-ohm feeder or coaxial cable may be used. In locations troubled by electrical interference, coaxial cable is preferable.
Orient so that the best reception is obtained.
5
Page 6
Before attempting to make any connections to or from this unit, be sure to first switch OFF the power to this unit and to any other
R L
A
B
75
UNBAL
PHONO CD AUX
A
B
FM
ANT
GND
AM
ANT
TAPEPBREC
OUT
TAPE 1
SPEAKERS
Video cassette player etc.
Turntable Compact disc player Tape deck 1
To AC outlet
Speakers A
Right Left
Right Left
Speakers B
TAPEPBREC
OUT
TAPE 2
Tape deck 2
R
L
OUTPUT
GND
REMOTE CONTROL
AUDIO OUT
LINE OUT
LINE IN
OUTPUT
LINE IN
LINE OUT
100W MAX. TOTAL
SWITCHED
AC OUTLETS
REMOTE CONTR0L
PHONO
GND
components to which connections are being made.
AUDIO CONNECTIONS
When making connections between this unit and other components, be sure all connections are made correctly, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Also, refer to the owner’s manual for each component to be connected to this unit.
RX-485 RDS
(Europe model)
6
* : Refer to “ABOUT THE ACCESSORY
TERMINALS” on page 8.
Page 7
RX-385, RX-385 RDS
R L
A
B
75
UNBAL
PHONO CD AUX
A
B
FM
ANT
GND
AM
ANT
TAPEPBREC
OUT
TAPE 1
SPEAKERS
Video cassette player etc.
Turntable Compact disc player Tape deck
To AC outlet
Speakers A
Right Left
Right Left
Speakers B
R
L
OUTPUT
GND
AUDIO OUT
OUTPUT
LINE IN
LINE OUT
100W MAX. TOTAL
SWITCHED
AC OUTLETS
GND
English
(Europe model)
* : Refer to “ABOUT THE ACCESSORY
TERMINALS” on page 8.
7
Page 8
CONNECTING SPEAKERS
Connect the SPEAKERS terminals to your speakers with wire of the proper gauge, cut to be as short as possible. If the connections are faulty, no sound will be heard from the speakers. Make sure that the polarity of the speaker wires is correct, that is, + and – markings are observed. If these wires are reversed, the sound will be unnatural and will lack bass.
Do not let the bare speaker wires touch each other and do not let them touch the metal parts of this unit as this could damage this unit and/or speakers.
One or two speaker systems can be connected to this unit. If you connect only one speaker system, connect it to either the SPEAKERS A or B terminals.
Use speakers with the specified impedance shown on the rear of this unit.
ABOUT THE ACCESSORY TERMINALS
AC OUTLET(S)
(Europe model) ...................................2 SWITCHED OUTLETS
(U.K. model) ..........................................1 SWITCHED OUTLET
Use these to connect the power cords from your components to this unit. The power to the SWITCHED outlets is controlled by this unit’s
POWER switch or the provided remote control transmitter’s POWER key. These outlets will supply power to any
component whenever this unit is turned on. The maximum power (total power consumption of components) that can be connected to the SWITCHED AC
OUTLET(S) is 100 watts.
How to Connect:
Red: positive (+) Black: negative (–)
Press up the tab.
Insert the bare wire.
[Remove approx. 5mm (1/4”) insulation from the speaker wires.] Press down the tab and
secure the wire.
REMOTE CONTROL (PHONO) connector
RX-485 RDS only
If you have a YAMAHA turntable with a terminal for remote control, connect it to this connector by using the cable provided with the turntable. This connection allows you to control the turntable from the provided remote control transmitter.
GND terminal (For turntable use)
Connecting the ground wire of the turntable to this terminal will normally minimize hum, but in some cases better results may be obtained with the ground wire disconnected.
8
Page 9
TAPE 1
MONITOR
COPY
INPUT
AUX TUNER
CD PHONO
TAPE 2
INPUT
AUX TUNER
CD PHONO
TAPE
MONITOR
SPEAKERS
A
B
ON
OFF
ON
OFF
2
— dB
VOLUME
0
POWER
0
— dB
VOLUME
English

OPERATIONS

3
1, 6
TO PLAY A SOURCE
1
Set to the “∞” position.
2
Select a desired input source.
3
RX-485 RDS
4
7
Select the speakers to be used.
4
* If you use two speaker systems, press both the A and B
switches.
Play the source. (For detailed information on the tuning
5
operations, refer to the page 12.)
6
RX-385, RX-385 RDS
* The name of the selected input source will appear in the
display.
* Note that pressing on each input selector button selects
the source which is connected to the corresponding input terminals on the rear panel.
Adjust to the desired output level.
If desired, adjust the BASS, TREBLE, BALANCE and
7
LOUDNESS controls, etc. (Refer to page 11.)
Notes
RX-485 RDS only
If you select AUX, TUNER, CD or PHONO, be sure that TAPE 1 and/or TAPE 2 are not being selected.
If you select TAPE 1 and TAPE 2 at the same time, the result will be the sound from the tape deck 1.
For TAPE 1 and TAPE 2, whenever the button is pressed, the corresponding input source is selected or canceled alternately.
RX-385 and RX-385 RDS only
If both TAPE MONITOR and another input selector button are selected, TAPE MONITOR has priority.
9
Page 10
TAPE 1
MONITOR
COPY
INPUT
AUX TUNER
CD PHONO
TAPE 2
COPY
TAPE 1
MONITOR
INPUT
AUX TUNER
CD PHONO
TAPE 2
1, 4
INPUT
AUX TUNER
CD PHONO
TAPE
MONITOR
INPUT
AUX TUNER
CD PHONO
TAPE
MONITOR
2
TO RECORD A SOURCE TO TAPE
RX-485 RDS
1
Select the source to be recorded.
* To dub from tape to tape, refer to the “Notes” shown
below.
* When you select AUX, TUNER, CD or PHONO, be sure
that TAPE 1 and/or TAPE 2 are not also selected.
2
Play the source and then turn the VOLUME control up to confirm the input source. (For detailed information on the tuning operations, refer to the page 12.)
3
Begin recording on the tape deck.
4
To monitor the audio signals being recorded, press the input selector button for the tape deck being used to make the recording.
TO RECORD A SOURCE TO TAPE
RX-385, RX-385 RDS
1
Select the source to be recorded.
* When you select AUX, TUNER, CD or PHONO, be sure
that TAPE MONITOR is not also selected.
2
Play the source and then turn the VOLUME control up to confirm the input source. (For detailed information on the tuning operations, refer to the page 12.)
3
Begin recording on the tape deck.
4
To monitor the audio signals being recorded, press the
TAPE MONITOR.
Notes
VOLUME, BASS, TREBLE, BALANCE and LOUDNESS control settings have no effect on the material being recorded.
To dub from tape to tape, only the following method of dubbing can be performed.
SOURCE
Tape deck connected to
the TAPE 2 terminals.
RECORDER
Tape deck connected to
the TAPE 1 terminals.
10
Note VOLUME, BASS, TREBLE, BALANCE and LOUDNESS
control settings have no effect on the material being recorded.
Page 11
Adjusting the BALANCE control Selecting the SPEAKER system
BALANCE
0
L5
5R
BASS
DEFEAT
5 +
5
TREBLE
DEFEAT
5 +
5
LOUDNESS
FLAT
30dB I0
LOUDNESS
FLAT
30dB I0
SPEAKERS
A
B
ON
OFF
ON
OFF
PHONES
PURE DIRECT
0
— dB
VOLUME
English
Adjust the balance of the output volume to the left and right speakers to compensate for sound imbalance caused from speaker location or listening room conditions.
Adjusting the BASS and TREBLE controls
BASS : Turn this clockwise to increase (or counter-
clockwise to decrease) the low frequency response.
TREBLE : Turn this clockwise to increase (or counter-
clockwise to decrease) the high frequency response.
Because one or two speaker systems can be connected to this unit, the SPEAKERS switches allow you to select speaker system A or B, or both at once.
Adjusting the continuously variable LOUDNESS control
This control provides compensation for the human ears’ loss of sensitivity to high and low-frequency ranges at low volume. This control is adjustable to retain full tonal range at any volume level.
1
Set to the “FLAT” position.
2
Set to the loudest listening level that you would listen to.
Using the PURE DIRECT switch
RX-485 RDS only
You can enjoy the purest possible sound from your audio sources by setting this switch ON. By doing so, the audio signal bypasses the BASS, TREBLE, BALANCE and LOUDNESS controls, eliminating any alterations to the audio signal.
3
Turn so that the desired volume can be achieved.
When you listen with headphones
Connect the headphones to the PHONES jack. When listening with headphones privately, set both the SPEAKERS A and B switches to the OFF position.
11
Page 12
FM/AM
AM
FM

TUNING OPERATIONS

FM/AM
TUNING
MODE
AUTO/MAN’L
MONO
TUNING
MODE
AUTO/MAN’L
MONO
TUNING
DOWN
UP
TUNING
DOWN
UP
STEREO
0
MHz
40 6020l00
FM
➀➁
STEREO
0
MHz
20
l00
FM
AUTO TUNING
AM
FM
Normally, if station signals are strong and there is no interference, quick automatic-search tuning (AUTOMATIC TUNING) is possible. However, if signals of the station you want to select are weak, you must tune to it manually (MANUAL TUNING).
3
2
1
AUTOMATIC TUNING MANUAL TUNING
1 Select the reception band (FM or AM) while watching
the display.
or
2
3
To tune to a higher frequency, press the right side once. To tune to a lower frequency, press the left side once. * If the station where tuning search stopped is not the
desired one, press again.
* If the tuning search does not stop at the desired station
(because the signals of the station are weak), change to the MANUAL TUNING method.
1 Select the reception band (FM or AM) while watching
the display.
or
2
“AUTO TUNING” goes off.
3 Tune to a desired station manually.
* To continue tuning search, press and hold the button.
Note
If you tune to an FM station manually, it is received in monaural mode automatically to increase the signal quality.
Display information
RX-385
RX-485 RDS, RX-385 RDS
12
Displays the band and frequency of the received station.
RX-485 RDS and RX-385 RDS only
If an RDS station is received, the frequency is then replaced by the station name. (However, if the PS data cannot be received within 5 seconds, “NO PS” flashes, and then it returns to the frequency display.) Refer to page 17 for details.
Illuminates when an FM stereo broadcast is received in
stereo. Indicates the signal level of the received station.
Page 13
MEMORY
MAN’L/AUTO FM
MEMORY
MAN’L/AUTO FM
PRESET
MEMORY
FM
A/B/C/D/E
PRESET
MEMORY
FM
A/B/C/D/E
PRESET
MEMORY
FM
PRESET
STATIONS
DOWN
UP
PRESET
STATIONS
DOWN
UP
AUTO TUNING
PRESET
STEREO
0
MHz
40 6020l00
FM
AUTO TUNING
PRESET
STEREO
0
MHz
20
l00
FM

PRESET TUNING

MANUAL PRESET TUNING
This unit can store station frequencies selected by tuning operation. With this function, you can recall any desired station by only selecting the preset station number where it is stored. Up to 40 stations (8 stations x 5 pages) can be stored.
3, 11
2, 5
4, 22
To store stations To recall a preset station
English
1 Tune to a desired station.
(Refer to the previous page for tuning procedures.)
2
Flashes on and off for about 5 seconds.
3 Select a desired page (A – E) of preset stations while
watching the display.
Select a preset station number (1–8) while watching the
4
display before “MEMORY” goes off from the display.
5
RX-385
11 Select the page where the preset station is stored.
22
Select the preset station number.
Notes
A new setting can be programmed in place of the former one.
For presets, the setting of the reception mode (stereo or monaural) is stored along with the station frequency.
Memory back-up
The memory back-up circuit prevents the programmed data from being lost even if the POWER switch is set off or the power plug is disconnected from the AC outlet or the power is cut due to temporary power failure. If, however, the power is cut for more than one week, the memory may be erased. If so, it can be re-programmed by simply following the PRESET TUNING steps.
Shows the displayed station has been programmed to A1.
RX-485 RDS, RX-385 RDS
Shows the displayed station has been programmed to A1.
* In the same way, program other stations to A2, A3 ... A8. * You can program more stations on other pages in the
same way by selecting other pages in step 3.
13
Page 14
AUTOMATIC PRESET TUNING
FM/AM
FM
MEMORY
MAN’L/AUTO FM
PRESET
MEMORY
AUTO TUNING
You can also make use of an automatic preset tuning function for FM stations only. By this function, this unit performs automatic tuning and stores FM stations with strong signals sequentially. Up to 40 stations are stored automatically in the same way as in the manual preset tuning method on page 13.
RX-485 RDS and RX-385 RDS only
* Only RDS stations can be stored by this function.
2
1
To store stations
When the automatic preset tuning is finished
1
2
Press and hold for about 3 seconds.
The display shows the frequency of the last preset station. Check the contents and the number of preset stations by following the procedure of the section “To recall a preset station” on page 13.
To recall a preset station
Simply follow the procedure of the section “To recall a preset station” on page 13.
RX-485 RDS and RX-385 RDS only
* A recalled station is shown by the frequency or station name
on the display.
and
Flashes. Flashes.
After 5 seconds, the automatic preset tuning begins from A1. Received stations are programmed to A1, A2 ... A8 sequentially. * If more than 8 stations are received, they are also
programmed to the preset station numbers on other pages (B, C, D and E) in that order.
If you want to store the first station received by the automatic preset tuning to a desired preset station number.
If, for example, you want to store the received first station to C5, select “C5” by using the A/B/C/D/E button and the PRESET STATIONS button soon after the display begins flashing on/off in step 2. After a few seconds, the automatic preset tuning begins. The received first station is stored to C5, and next stations to C6, C7 ... sequentially. If stations are stored up to E8, the automatic preset tuning is finished automatically.
Notes
You can replace a preset station by another FM or AM station manually by simply following the procedure of the section “To store stations” on page 13.
RX-385 only
If the number of received stations is not enough to be stored up to E8, the search is finished automatically when it reaches the highest frequency after searching through all frequencies.
With this function, only FM stations with sufficient signal strength are stored automatically. If the station you want to program is week in signal strength, tune to it in monaural manually and program it by following the procedure of the section “To store stations” on page 13.
RX-485 RDS and RX-385 RDS only
The automatic preset tuning search will be performed through all RDS network frequencies until stations are stored up to E8. If the number of received stations is not enough to be stored up to E8, the search is finished automatically after searching through all frequencies.
With this function, only RDS stations with sufficient signal strength are stored automatically. If the station you want to program is weak in signal strength, tune to it in monaural manually and program it by following the procedure of the section “To store stations” on page 13. * There may be a case that this function cannot receive a
station which could be received by the automatic tuning method. This is because this function receives a large volume of PI (Program Identification) data along with the station.
14
Page 15
EXCHANGING PRESET STATIONS
EDIT
EDIT
You can exchange the places of two preset stations each other by easy operations.
2, 4
Example)
If you want to shift the preset station on E1 to A5, and vice versa.
English
1 Recall the preset station on E1 (by following the method
of “To recall a preset station” on page 13).
2
Flashes
3 Next, recall the preset station on A5 by following the
same method with step 1.
Flashes
4
Shows the exchange of stations is completed.
15
Page 16
RECEIVING RDS STATIONS
RX-485 RDS
RDS (Radio Data System) is a data transmission system gradually being introduced by FM stations in many countries. Stations using this system transmit an inaudible stream of data in addition to the normal radio signal. RDS data contains various information, such as AF (Alternative Frequencies for the same program station), PI (Program Identification), PS (Program Service station name), PTY (Program Type name), etc. RDS function is carried out among the network stations. * This unit utilizes AF, PI, PS and PTY to receive RDS broadcast stations.
and
RX-385 RDS
only
Displaying RDS data
This unit can be turned into the following two modes to display RDS data.
PS (Program Service station name) mode:
Displays the name of the RDS station now being received instead of the frequency.
PTY (Program Type name) mode:
Displays the program type of the RDS station now being received. There are 15 program types to classify RDS stations as follows.
News:
NEWS
AFFAIRS
INFO
Short accounts of facts, events and publicly expressed views, reportage and actuality.
Current affairs:
Topical program expanding or enlarging upon the news, generally in different presentation style or concept, including documentary debate, or analysis
Information:
Program whose purpose is to impart advice in the widest sense, including meteorological reports and forecasts, consumer affairs, medical help, etc.
VARIED
POP M
ROCK M
BBC R3
Varied:
Used for mainly speech-based programs usually of light-entertainment nature, not covered by above categories. Examples are: quizzes, panel games, personality interviews, comedy and satire.
Pop:
Commercial music, which would generally be considered to be of current popular appeal, often featuring in current or recent record sales charts.
Rock:
Contemporary modern music, usually written and performed by young musicians.
Sport:
SPORT
EDUCATE
DRAMA
CULTURE
SCIENCE
Program concerned with any aspect of sport.
Education:
Program intended primarily to educate, of which the formal element is fundamental.
Drama:
All radio plays and serials.
Culture:
Programs concerned with any aspect of national or regional culture, including religious affairs, philosophy, social science, language, theatre, etc.
Science:
Programs about the natural sciences and technology.
16
MOR M
LIGHT M
CLASSICS
OTHER M
M.O.R.:
(Middle of the Road Music). Common term to describe music considered to be “easy­listening”, as opposed to Pop, Rock or Classical. Music in this category is often but not always, vocal, and usually of short duration (<5 min.)
Light classics:
Classical Musical for general, rather than specialist appreciation. Examples of music in this category are instrumental music, and vocal or choral works.
Serious classics:
Performances of major orchestral works, symphonies, chamber music etc., and including Grand Opera.
Other music:
Musical styles not fitting into any of the above categories. Particularly used for specialist music, of which Jazz, Rhythm & Blues, Folk, Country, and Reggae are examples.
Page 17
To turn the unit into the PS mode or PTY mode
FREQ/PS/PTY SHIFT ENTER
PS/PTY SEEK
Press the FREQ/PS/PTY button. Whenever pressed, the mode changes into the PS mode, PTY mode and returns to usual mode in turn. * When an RDS station is received, the display is automatically turned into the PS mode. Do not press the FREQ/PS/PTY button
until the display is turned into the PS mode. If the button is pressed before the display mode is changed, it may occur that “NO PS” flashes on the display. This is because the unit has not received all of the RDS data on the station yet.
PS mode The name of the station being received is displayed.
If the station is not an RDS station, “NO PS” flashes on the display and then returns to usual mode.
PTY mode A program type for the station being received is displayed.
If the RDS station does not employ the PTY data service, “NO PTY” flashes on the display and then returns to the PS mode. If the station is not an RDS station, “NO PTY” flashes on the display and then returns to usual mode.
English
Usual mode The frequency of the station being received is displayed.
Note
When PS or PTY data reception is not possible due to poor reception conditions, “NO PS” or “NO PTY” flashes on the display in each mode. In such a case, press the TUNING MODE button so that “AUTO TUNING” goes off from the display. Though the reception mode is changed to monaural by this operation, when you changes to the PS or PTY mode, PS or PTY data may be displayed.
17
Page 18
Calling a preset RDS station by the station name (PS SEEK)
FM/AM
FM
ENTER
FREQ/PS/PTY SHIFT ENTER
PS/PTY SEEK
FREQ/PS/PTY SHIFT ENTER
PS/PTY SEEK
PRESET
STATIONS
DOWN
UP
FREQ/PS/PTY SHIFT ENTER
PS/PTY SEEK
TUNING
DOWN
UP
FREQ/PS/PTY SHIFT ENTER
PS/PTY SEEK
You can call a desired RDS station stored in this unit by only inputting the name of the station in the PS mode. By this operation, this unit searches all preset stations for the station. You do not have to input a full name, even only the first letter can be used for calling. As many as 8 letters and/or numerals can be selected for inputting a name.
8
4
1
1
2 Turn the unit into the PS mode.
A station name is displayed or “NO PS” flashes.
* If “NO PS” flashes, proceed to the next step while flashing.
If “NO PS” disappears before you proceed to the next step, press the FREQ/PS/PTY button again.
2, 3, 5, 7
6 Repeat steps 4 and 5 for other letters and/or numerals,
if necessary.
7 When inputting the name is finished, press the ENTER
button.
Flashes.
3
Flashes.
4 Select the first letter or numeral of the station name.
* By pressing the TUNING button repeatedly or by pressing
and holding it, the display will change letters and numerals in sequence.
* If you will not input the second letter, skip to step 7.
5 When the first letter or numeral of the station name
appears, press the SHIFT button to proceed to the selection of the next letter or numeral.
18
“A” will flash on the second letter or numeral position.
8
Press once.
The unit begins searching for the station, and it is continued until the station is found.
You do not have to input a full name for searching for the station
You may input only the first letter of the station name. If doing so, you can skip steps 5 and 6. In step 8, the unit searches for and calls a nearest station which has the letter you input. If the station is not the desired one, press the PRESET STATIONS button again. The unit will begin searching for another station which has the same letter.
To cancel this function
Press the AF, FREQ/PS/PTY, SHIFT, ENTER, FM/AM or MEMORY button.
Notes
If no station is found by this function after searching all preset stations, “NO PS” flashes for about 3 seconds on the display, and then it returns to the mode which had been obtained before the searching was performed.
This function is useful especially for calling a station with weak signals which cannot be received by the automatic tuning method. By only storing such a station, you can call it any time easily.
Page 19
Calling a preset RDS station by the program type (PTY SEEK)
FREQ/PS/PTY SHIFT ENTER
PS/PTY SEEK
FREQ/PS/PTY SHIFT ENTER
PS/PTY SEEK
PRESET
STATIONS
DOWN
UP
FREQ/PS/PTY SHIFT ENTER
PS/PTY SEEK
TUNING
DOWN
UP
By designating a program type, the unit automatically searches all preset stations for RDS stations of that program type. * There are 15 program types to classify RDS stations. For details, refer to page 16.
5
3
1, 2, 4
English
1 Turn the unit into the PTY mode.
Press once or twice until a program type is displayed or “NO PTY” flashes.
* If “NO PTY” flashes, proceed to the next step while
flashing. If “NO PTY” disappears before you proceed to the next step, press the FREQ/PS/PTY button once or twice.
2
The program type of the station now being received or “NEWS” flashes on the display.
3 Select the desired program type.
4 When the desired program type appears, press the
ENTER button.
ENTER
Flashes.
5
Press once.
The unit begins searching all preset stations, and calls a station of the program type if such a station is found.
* When the right side of the PRESET STATIONS button is
pressed, the search is performed from “A1” toward higher numbers of the preset stations (A1, A2 ... A8, B1, B2, ...). If, however, “A3” is currently being called for example, the search begins from the next station “A4”. When the left side of the PRESET STATIONS button is pressed, the search is performed in reverse order.
If the called station is not the desired one, press the PRESET STATIONS button again to search for another station of the same program type.
* By pressing the TUNING button repeatedly or by pressing
and holding it, the display will change program types in sequence.
To cancel this function
Press the AF, FREQ/PS/PTY, SHIFT, ENTER, FM/AM or MEMORY button.
Note
If no station is found by this function, after searching all preset stations, “NO PTY” flashes for about 3 seconds on the display, and then it returns to the mode which had been obtained before the searching was performed.
19
Page 20
Calling the best quality RDS station which broadcasts the
same program (AF SEEK)
This function automatically searches for and calls another RDS station of the best reception quality which broadcasts the same program now you are listening to. This function utilizes AF (Alternative Frequencies for the same program station) and PI (Program Identification) of RDS data service. The search is carried out among the RDS network stations.
2, 3
1 Tune to a desired RDS station.
* Wait for about 10 seconds before proceeding to the
next step. This is for making this unit carry out searching more stations.
2
The unit searches network stations for other stations with the same program. * If the station is not an RDS station, or there is no other
Stations with the same program are all stored and numbered from the best quality station in sequence.
AF
station with the same program, “NO AF” flashes.
3 If desired, you can call the second station by pressing
the AF button.
AF
Whenever the AF button is pressed, stored stations are called in sequence. When pressed after the last station is selected, the first one is restored.
To cancel this function
Press a button other than the AF button. All of the stored stations will be also cleared.
When the search is finished, the best quality station is called.
20
Page 21

REMOTE CONTROL TRANSMITTER

POWER SLEEP
PLAY/CUT
PHONO
SKIP PLAY CD
SEARCH PAUSE/STOP DISC SKIP
+
A/B/C/D/E
TUNER
DIR A
DECK A/B
DIR B TAPE 1
TAPE 2
REC/PAUSE
STOP
REC MUTE
AUX
VOLUME
+
PRESET
PLAY
The remote control transmitter provided with this unit is designed to control all the most commonly used functions of the unit. If the CD player, turntable and tape deck connected to this unit are YAMAHA components, then this remote control transmitter will also control various functions of each component.
KEY FUNCTIONS
English
For Control of This Unit
The power to the receiver is automatically turned off one hour after this key is
Turns the power on/off.
pressed (so that “SLEEP” illuminates on the display).
Selects preset station number
+ : Selects higher preset station number.: Selects lower preset station number.
Selects input source.
A/B/C/D/E: Selects the page (A – E) of
preset stations.
Turns the volume level up/down.
For Other Component Control
Identify the remote control transmitter keys with your component’s keys. If these keys are identical, their function will be the same. On each key function, refer to the corresponding instruction on your component’s manual.
Starts/stops record play on turntable.
POWER SLEEP
SKIP PLAY CD
PLAY/CUT
PHONO
Controls compact disc player. * DISC SKIP is applicable only to
compact disc changer.
Illustrations : RX-485 RDS
* PLAY/CUT is equipped only on RX-485 RDS. * TAPE 1 and TAPE 2 are equipped only on RX-485 RDS. On RX-385 and RX-385 RDS, they are replaced by TAPE only.
SEARCH PAUSE/STOP DISC SKIP
PRESET
+
A/B/C/D/E
DIR A
DECK A/B
DIR B TAPE 1
PLAY
REC/PAUSE
STOP
REC MUTE
VOLUME
TUNER
TAPE 2
AUX
+
Controls tape deck. * DIR A, B and DECK A/B are
applicable only to double cassette tape deck.
* For a single cassette deck with
automatic reverse function, pressing DIR A will reverse the direction of tape running.
21
Page 22
2
3
1
30°
30°
STANDBY mode (Europe model only) While the power is on, pressing the POWER key on the remote control transmitter switches the unit to the STANDBY mode. (In this mode, the standby indicator on the front panel is half illuminated.)
POWER on mode

NOTES ABOUT THE REMOTE CONTROL TRANSMITTER

Battery installation
Battery replacement
If you find that the remote control transmitter must be used closer to the main unit, the batteries are weak. Replace both batteries with new ones.
Notes
Use only AA, R6, UM-3 batteries for replacement.
Be sure the polarities are correct. (See the illustration inside the battery compartment.)
Remove the batteries if the remote control transmitter will not be used for an extended period of time.
If batteries leak, dispose of them immediately. Avoid touching the leaked material or letting it come in contact with clothing, etc. Clean the battery compartment thoroughly before installing new batteries.
Remote control transmitter operation range
Remote control sensor
Notes
There should be no large obstacles between the remote control transmitter and the main unit.
If the remote control sensor is directly illuminated by strong lighting (especially an inverter type of fluorescent lamp etc.), it might cause the remote control transmitter not to work correctly. In this case, reposition the main unit to avoid direct lighting.
STANDBY mode
Within approximately 7 m (23 feet)
22
Page 23

TROUBLESHOOTING

If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and contact your authorized YAMAHA dealer or service center for help.
English
SYMPTOM
The unit fails to turn on when the POWER switch is pressed.
No sound.
The sound suddenly goes off.
Only one side speaker outputs the sound.
AmplifierFMAM
Sound “hums”.
The volume level is low while playing a record.
The volume level cannot be increased, or sound is distorted.
FM stereo reception is noisy.
There is distortion and clear reception cannot be obtained even with a good FM antenna.
A desired station cannot be tuned in with Auto tuning.
A desired station cannot be tuned in with Auto tuning.
There are continuous crackling and hissing noises.
There are buzzing and whining noises (especially in the evening).
The remote control transmitter does not work.
transmitter
Remote control
The sound is degraded when monitoring is performed by using the headphones connected to the compact disc player or cassette deck
Others
which are connected with this unit.
CAUSE
Power cord is not plugged in or is not completely inserted.
Incorrect output cord connections.
Appropriate input selector button is not pressed.
The protection circuit has activated because of short circuit etc.
Incorrect setting of the BALANCE control Incorrect cord connection.
Incorrect cord connections.
No connection from the turntable to the GND terminal.
The record is being played on a turntable with an MC cartridge.
The power to the component connected to the REC OUT terminals of this unit is off.
Because of the characteristics of FM stereo broadcasts, this is limited to cases where the transmitter is too far or the antenna input is poor.
There is multipath interference.
The station is too weak.
Weak signal or loose antenna connections.
Noises will result from ligtning, fluorescent lamps, motors, thermostats and other electrical equipment.
A television set is being used nearby.
Direct sunlight or lighting (of an inverter type of flourescent lamp etc.) is striking the remote control sensor of the main unit.
The batteries of this remote control transmitter are too weak.
The power to this unit is off.
REMEDY
Firmly plug in the power cord.
Connect the cords properly. If the problem persists, the cords may be defective.
Press the appropriate input selector button corresponding to the input source.
Turning the unit off and then on will reset the protection circuit.
Adjust it to the appropriate position. Connect the cord properly. If the problem persists,
the cables may be defective. Firmly connect the audio plugs. If the problem
persists, the cord may be defective. Make the GND connection between the turntable
and this unit. The player should be connected to the receiver
through the MC head amplifier. Turn the power to the component on.
Check the antenna connections. Try using a multiple element FM antenna.
Adjust antenna placement to eliminate multipath interference.
Use Manual tuning mode. Use high quality directional FM antenna.
Use Manual tuning mode. Tighten the AM loop antenna connections and
rotate it for best reception. Use an outdoor antenna and a ground wire. This
will help somewhat but it is difficult to eliminate all noises.
Relocate this unit away from the TV.
Change position of the main unit.
Replace the batteries with new ones.
Turn the power to this unit on.
23
Page 24

SPECIFICATIONS

AUDIO SECTION
Minimum RMS Output Power per Channel
8 ohms, 20 Hz to 20 kHz, 0.04% THD
<RX-485 RDS>............................65W+65W
<RX-385/385 RDS>
[U.S.A. and Canada models].......45W+45W
[Australia, U.K., Europe and
General models]..........................40W+40W
6 ohms, 20 Hz to 20 kHz, 0.06% THD
<RX-485 RDS>............................70W+70W
<RX-385/385 RDS>
[U.S.A. and Canada models].......48W+48W
Dynamic Power per Channel (by IHF Dynamic Headroom measuring
method)
<RX-485 RDS>
8/6/4/2 ohms....................95/115/135/150W
<RX-385/385 RDS>
[U.S.A., Canada and General models]
8/6/4/2 ohms..........................69/78/90/98W
[Australia, Europe and U.K. models]
8/6/4/2 ohms..........................68/75/85/95W
DIN Standard Output Power per Channel
4 ohms, 1 kHz, 0.7% THD
[Europe model only]
<RX-485 RDS>......................................85W
<RX-385/385 RDS>...............................55W
IEC Power
<RX-485 RDS>
8 ohms, 1 kHz, 0.04% THD
[Europe model only]..............................75W
<RX-385/385 RDS>
8 ohms, 1 kHz, 0.04% THD
[Europe model only]..............................50W
Damping Factor
8 ohms, 20 Hz to 20 kHz ............................80
Input Sensitivity/Impedance
PHONO MM ......................2.5 mV/47 k-ohms
CD/TAPE/AUX..................150 mV/47 k-ohms
Maximum Input Signal (1 kHz, 0.01% THD)
PHONO MM.........................................80 mV
Headphone Jack Rated Output/Impedance
8 ohms, 20 Hz to 20 kHz, 0.04% THD Output Level
<RX-485 RDS>....................................0.46V
<RX-385/385 RDS>.............................0.45V
Impedance
<RX-485 RDS>.............................390 ohms
<RX-385/385 RDS>......................330 ohms
Frequency Response (20 Hz to 20 kHz)
CD/TAPE/AUX..................................0±0.5 dB
RIAA Equalization Deviation
PHONO MM.....................................0±0.5 dB
Total Harmonic Distortion (20 Hz to 20 kHz)
PHONO MM to REC OUT (1V) ............0.02%
CD/TAPE/AUX to SP OUT
<RX-485 RDS>
(32.5W/8 ohms)....................................0.02%
<RX-385/385 RDS>
(22.5W/8 ohms)....................................0.02%
Signal-to-Noise Ratio (IHF-A Network)
PHONO MM (5 mV Input Shorted)........82 dB
CD/TAPE/AUX (Input Shorted) ...........105 dB
Residual Noise (IHF-A Network)............100 µV
Channel Separation (Vol. –30 dB)
PHONO MM (Input Shorted 1 kHz).......60 dB
CD/TAPE/AUX
(Input 5.1 k-ohms Terminated 1 kHz)....60 dB
Tone Control Characteristics
BASS: Boost/cut .................±10 dB (50 Hz)
(Turnover frequency)
...........................................(350 Hz)
TREBLE: Boost/cut............±10 dB (20 kHz)
(Turnover frequency)
..........................................(3.5 kHz)
Continuous Loudness Control
...............................................– 30 dB (1 kHz)
(Level related equalization)
FM SECTION
Tuning Range
[U.S.A., Canada and General models]
........................................87.5 to 107.9 MHz
[Australia, Europe, U.K. and General
models]...........................87.5 to 108.0 MHz
50 dB Quieting Sensitivity (IHF, 75 ohms)
<RX-485 RDS/385>
[Except Europe model]
Mono...............................1.55 µV (15.1 dBf)
Stereo................................21 µV (37.7 dBf)
<RX-385 RDS>
Mono...............................1.55 µV (15.1 dBf)
Stereo................................21 µV (37.7 dBf)
Usable Sensitivity (75 ohms)
(30 dB S/N Quieting, 1 kHz, 100% mod.)
<RX-485 RDS/385>
[Except Europe model]
............................................0.8 µV (9.3 dBf)
DIN, Mono (S/N 26 dB) [Europe model]
.............................................................0.9 µV
DIN, Stereo (S/N 46 dB) [Europe model]
..............................................................24 µV
<RX-385 RDS>
[Except Europe and U.K. models]
............................................0.8 µV (9.3 dBf)
DIN, Mono (S/N 26 dB)
[Europe and U.K. models] .................0.9 µV
DIN, Stereo (S/N 46 dB)
[Europe and U.K. models] ..................24 µV
Image Response Ratio
<RX-485 RDS/385>
[Except Europe and U.K. models].......45 dB
[Europe model] ...................................80 dB
<RX-385 RDS>
[Except Europeand U.K. models]........45 dB
[Europe and U.K. models]...................80 dB
IF Response Ratio...................................80 dB
Spurious Response Ratio........................70 dB
AM Suppression Ratio.............................55 dB
Capture Ratio..........................................1.5 dB
Alternate Channel Selectivity
<RX-485 RDS/385>
[Except Europe model] .......................85 dB
<RX-385 RDS>
[Except Europe and U.K. models].......85 dB
Selectivity (two signals, 40 kHz Dev.)
<RX-485 RDS/385>
[Europe model] ...................................70 dB
<RX-385 RDS>
[Europe and U.K. models]...................70 dB
Signal-to-Noise Ratio
<RX-485 RDS/385>
(IHF) Mono/Stereo
[Except Europe model].............80 dB/75 dB
(DIN-Weighted, 40 kHz Dev.) Mono/Stereo
[Europe model].........................74 dB/69 dB
<RX-385 RDS>
(IHF) Mono/Stereo
[Except Europe and U.K. models]
.................................................80 dB/75 dB
(DIN-Weighted, 40 kHz Dev.) Mono/Stereo
[Europe and U.K. models]........74 dB/69 dB
Harmonic Distortion
<RX-485 RDS/385>
Mono/Stereo (1 kHz)
Mono/Stereo (40 kHz Dev.)
<RX-385 RDS>
Mono/Stereo (1 kHz)
Mono/Stereo (40 kHz Dev.) Stereo Separation
<RX-485 RDS/385> (1 kHz)................50 dB
24
[Except Europe model]................0.1/0.2%
[Europe model]............................0.1/0.2%
[Except Europe and U.K. models]
....................................................0.1/0.2%
[Europe and U.K. models]...........0.1/0.2%
<RX-385 RDS>
[Except Europe and U.K. models]
(1 kHz)...................................................50 dB
[Europe and U.K. models]
(40 kHz Dev.) ........................................50 dB
Frequency Response
20 Hz to 15 kHz...............................0 ±1.5 dB
AM SECTION
Tuning Range
[U.S.A., Canada and General models]
..........................................530 to 1,710 kHz
[Australia, U.K., Europe and General
models] .............................531 to 1,611 kHz
Usable Sensitivity ..............................100 µV/m
Selectivity.................................................32 dB
Signal-to-Noise Ratio...............................50 dB
Image Response Ratio ............................40 dB
Spurious Response Ratio........................50 dB
Harmonic Distortion...................................0.3%
AUDIO SECTION
Output Level/Impedance
<RX-485 RDS/385>
FM (100% mod., 1 kHz)
[Except Europe model]
......................................500 mV/2.2 k-ohms
[Europe model (40 kHz Dev.)]
......................................400 mV/2.2 k-ohms
AM (30% mod., 400 Hz)
.........................................150 mV/2.2 k-ohms
<RX-385 RDS>
FM (100% mod., 1 kHz)
[Except Europe and U.K. models]
......................................500 mV/2.2 k-ohms
[Europe and U.K. models (40 kHz Dev.)]
......................................400 mV/2.2 k-ohms
AM (30% mod., 400 Hz)
.........................................150 mV/2.2 k-ohms
GENERAL
Power Supply
[U.S.A. and Canada models]
...........................................AC 120V, 60 Hz
[Australia and U.K. models]
...........................................AC 240V, 50 Hz
[Europe model]...................AC 230V, 50 Hz
[General model]
.................AC 110/120/220/240V, 50/60 Hz
Power Consumption
<RX-485 RDS>
[U.S.A. model].....................................155W
[Canada model].....................250 VA, 205W
[Europe, Australia and General models]
............................................................135W
<RX-385/385 RDS>
[Canada model] ..................................170W
[U.S.A., Australia, Europe, U.K. and
General models] .................................120W
AC Outlets
2 SWITCHED OUTLETS
[U.S.A., Canada, Europe and
General models].................100W max. total
1 SWITCHED OUTLET
[Australia and U.K. models]
...........................................100W max. total
Dimensions (W x H x D)
..........................................435 x 126 x 298 mm
(17-1/8” x 4-15/16” x 11-3/4”)
Weight
<RX-485 RDS>.............7.0 kg (15 lbs. 6 oz.)
<RX-385/385 RDS>......6.1 kg (13 lbs. 7 oz.)
Accessories............................AM loop antenna
Indoor FM antenna
Remote control transmitter
Batteries
Specifications are subject to change without notice.
Page 25
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
Page 26
documentation manual, user maintenance, brochure, user reference, pdf manual
This file has been downloaded from:
User Manual and User Guide for many equipments like mobile phones, photo cameras, monther board, monitors, software, tv, dvd, and othes..
Manual users, user manuals, user guide manual, owners manual, instruction manual, manual owner, manual owner's, manual guide,
manual operation, operating manual, user's manual, operating instructions, manual operators, manual operator, manual product,
Loading...