Yamaha Audio RS150 User Manual

RS150

ASSEMBLY INSTRUCTIONS

INTRODUCTION

Thank you for purchasing the Yamaha Electronic Drum Rack System RS150.
Before using, thoroughly read these assembly instructions, and use this product
safely and correctly.

PRECAUTIONS

Before using, please read this “Assembly In­struction” sheet, and use this product in a safe

and proper manner.
Especially for children, parents or an instructor
should teach the children the proper manner in
which to use the device.

WARNING

Always set the instrument on a flat and solid surface. Placement on a sloping, unstable surface or on steps may result in the
instrument being unstable and overturning.

Make sure all bolts are tightened firmly. Loose bolts may result in the rack overturning or parts dropping causing injury.

When adjusting the height or angle, do not suddenly loosen the bolt. The pad may drop, the rack or pipes may slip, pinching or
causing injury to hands or fingers.

Do not sit or step on the rack. The rack may overturn or be damaged resulting in injury.

Please be careful when children are close to or touching the product. The product has many pipes and arms so careless
movement around the product may result in injury.

When setting the pads and modules, please pay close attention in regards to the handling and setting of cables. Feet may
become entangled in the cables resulting in falls.

CAUTION

If this symbol is ignored and the equipment is used improperly, fatal injury to per-

sons or serious damage could occur.

If this symbol is ignored and the equipment is used improperly, there is a danger

of injury to persons handling the equipment, and material damage could occur.

To prevent against accidents and injury

Please follow the cautions listed below

Caution (including danger, or warning). This
mark indicates cautions in which you should
pay close attention to.

Acts indicated with this icon are prohibited and
should not be attempted.

■ Handling Precautions

• Do not alter the product. Doing so may result in damage or deterioration to the product.

• Do not step on or place heavy objects on the product. It may result in damage.

• Do not use or keep the product in places with extremely high temperature (places in direct sunlight, close to
a heater, in a closed car, etc.) or damp (bathroom, outside on a rainy day, etc.). It may result in deformation,
discoloration, stickiness, damage or deterioration.

•To clean the product, please wipe with a soft cloth or a damp cloth that has been wrung out thoroughly. If the
product is soiled or sticky, use a neutral detergent on a cloth then wipe with a damp cloth that has been
wrung out thoroughly to remove any remaining detergent.
result in discoloration or deformation. Also pay close attention so as not to let the water and detergent come
into contact with the cushions used in the product, it may result in deterioration.

Do not use benzine, thinner or alcohol as it may

■ Inside This Package

Before setup, please make sure that all of the items listed below are present and ac­counted for. If anything is missing, please contact the dealer from whom you purchased
the unit.

* Before assembling the rack stand, make sure all of the parts shown below are included.

◆Piller（L）

◆ModuleHolder

◆TomClampCL-940A（x4）

◆Piller（C）

◆CrossPipe

◆Piller（R）

Leg Connector

◆CenterPipe（A）

Holder Clamp

◆CenterPipe（B）

Holder Clamp

◆CenterPipe（C）

◆CenterPipe（D）

◆CymbalHolderCH745

Do not put your hands or feet under the foot pedal or foot switch. They may be pinched resulting in injury.

Watch your fingers when adjusting clamps. They may become pinched resulting in injury.

Be careful around pipe ends, inside the pipe and screw ends. Metal shavings, etc. may injure your fingers.

Do not attach acoustic drums to the electronic drum rack. Clamps may be damaged and drums may drop, causing injury.

* Specifications are subject to change without notice.

◆CymbalHolderCH740（x2）

◆SmallScrewsM5x8

（ModuleHolderFixingScrewsx4）

◆AssemblyInstructions

（thissheet）

◆CableBand（x10）

■ RS150 Assembly

* Parts for the RS150's main structure have already been assembled before packing. After removing the unit from the box, follow the instructions described below to complete the assembly.

II

A Phillips (+) screwdriver is required when attaching the DTXTREME

After removing the unit from the box, remove all cushion material.

1

Setting up the parts

2

Follow the setup order (q~o) in the diagrams shown below.

q Temporarily remove the leg connector from pillar (R).
w Attach center pipe (D) to pillar (R) and pillar (C), and secure.
e Reattach the leg connector.

r Attach the cross pipe to the leg connector.
t Attach center pipe (C) to pillar (L) and pillar (C), and secure.

Caution : Make sure the bolts marked with a " " are loosened before setting up.

Piller (L)

i

Holder Clamp Holder Clamp

Module Holder

Center Pipe (A)

u

Piller (C)

Holder Clamp

Center Pipe (B)

Holder Clamp

t

Caution

$

Center Pipe (C)

y

w

Leg (L)

Leg (C)

Center Pipe (D)

Cross Pipe

Leg (R)

S. Please prepare one before starting assembly.

y Attach center pipe (B) to pillar (R) and pillar (C), and secure.
u Attach center pipe (A) to pillar (L) and pillar (C), and secure.
i Attach the module holder to pillar (L), and secure.
o Attach the cymbal holders and tom clamps to the holder clamps, and secure.

Cymbal Holder

(CH740)

Piller (R)

Leg Connector

Remove temporarily.

q

Tighten knob of

e

leg connector

r

Leg Connector

Cymbal Holder

Tom Clamp

(CL-940A)

o

(CH740)

Tom Clamp

(CL-940A)

o

o

o

Holder Clamp

Holder Clamp

Memory Clamps

Using the memory clamps let you obtain the same
height setting for all future setups.

Cymbal Holder

(CH745)

Tom Clamp

(CL-940A)

o

o

■ Optional Parts

● Pad and Drum Trigger Grouping

II

q DTXTREME

Drum Trigger Module

S

w PCY130/130S

Cymbal Pad

e PCY150S

Cymbal Pad

r RHH130

Real Hi-hat Pad

■ Set up example

Satellite Speaker

q

PCY130S

w

PCY150S

e

Satellite Speaker

w

PCY130

t TP100

Drum Pad

u KP65

Kick Pad

y TP120SD

Drum Pad

i Foot Pedal

* DFP-9310 etc.

o Snare Stand

*SS652 etc.

● Monitor System and Attachement Grouping

• SPAT1

(1 set L/R units)

• CYAT150

!0 Hi-hat Stand

*HS-740 etc.

• TPCL150

r

!0

y

o

t

t

u

i

• MS50DR

• Sub Woofer

amp unit

Attaching the DTXTREME IIS

3

• Satellite
Speakers

• MS100DR

• Sub Woofer

3-1 Remove the module holder from the holder clamp, and

use the supplied screws to attach the DTXTREME

Make sure only the supplied screws are used. Using any
other screws may result in the unit falling off the holder
or damage.

3-2 Slide the module holder, with the DTXTREME

attached, into the holder clamp.

II

amp unit

II

S.

S already

• Satellite
Speakers

Sub Woofer amp unit

Attaching the cymbal pads

4

Attach the cymbal pads to the cymbal holders and adjust their
position, then secure in place. (Please refer to the Owner's
Manual that came with the cymbal pads on attaching the cym­bal pads.)

Attaching the drum pads

5

Attach the drum pads to the tom clamp and adjust their posi­tion, then secure in place.

DTXTREME

Module
Holder

Maker sure all bolts on clamps, pads, etc., are tightened firmly.
However, loose or over-tightened bolts may result in the part falling off and/or damage. Please use caution.
After assembly is complete, setup the kick pad, real hi-hat pad, etc., and connect the cables. Use the supplied cable bands to secure the cables
to the frame pipes to keep cables out of the way during performance.
If the rack is moved even after setup is complete, make sure the bolts are loosened before moving the rack.

II

Step 3-1

S

Step 3-2

Holder Clamp

Step 3

Step 5

Drum Pad

Step 4

Felt

Cymbal Pad
(PCY130/130S/150S)

Anti-swivel brace
(supplied with the
(PCY130/130S/150S)

Printed in Indonesia

WG24090