Yamaha Audio 02R96 User Manual

Studio Manager
for
/
Installation Guide
Keep This Manual For Future Reference.
E
Important Information
Exclusion of Certain Liability
Manufacturer, importer, or dealer shall not be liable for any incidental damages including personal injury or any other damages caused by improper use or operation of Studio Man­ager for DM2000 or Studio Manager for 02R96.
Yamaha makes no representations or warranties with regard to the use of the software and documentation and cannot be held responsible for the results of the use of this manual and the software.
Use of the software and this manual is governed by the Software Licensing Agreement which the purchaser fully agrees to upon breaking the seal of the software packaging. (Carefully read the agreement at the end of this manual before installing the software.)
Trademarks
Adobe, Acrobat, and Reader are registered trademarks of Adobe Systems Incorporated. Apple, AppleTalk, and Macintosh are registered trademarks of Apple Computer, Inc. Microsoft and Windows are registered trademarks of Microsoft Corporation. OMS is a reg­istered trademark of Opcode Systems, Inc. Pentium and Celeron are registered trademarks of Intel Corporation. PowerPC is a registered trademark of International Business Machines Corporation. SmartMedia is a trademark of Toshiba America, Inc. All other trademarks are the property of their respective holders and are hereby acknowledged.
Copyright
No part of the Studio Manager for DM2000 or Studio Manager for 02R96 software or its documentation may be reproduced or distributed in any form or by any means without the prior written authorization of Yamaha Corporation.
© 2002 Yamaha Corporation. All rights reserved.
Yamaha Web Site
Information about Studio Manager for DM2000, Studio Manager for 02R96, related prod­ucts, and other Yamaha professional audio equipment is available on the Yamaha Profes­sional Audio Web site at: <http://www.yamaha.co.jp/product/proaudio/homeenglish/navi/index.htm>.
Specifications and external appearance subject to change without notice.
Studio Manager for DM2000/02R96—Installation Guide
ii

Contents

1 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
CD-ROM Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Windows System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Macintosh System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
DM2000/02R96 Hookup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Configuring the DM2000/02R96 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2 Windows Installation . . . . . . . . . . . . . . . . . . . . . . . 5
Acrobat Reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
USB MIDI Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Yamaha CBX Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Studio Manager for DM2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Studio Manager for 02R96 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Card Filer (DM2000 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3 Macintosh Installation . . . . . . . . . . . . . . . . . . . . . . 12
Acrobat Reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
OMS (Open Music System) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
USB MIDI Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Studio Manager for DM2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Studio Manager for 02R96 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Card Filer (DM2000 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Setting up OMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Studio Manager for DM2000/02R96—Installation Guide

1 Getting Started

Introduction

The Yamaha Studio Manager application allows you to control the Yamaha DM2000 Digital Production Console or Yamaha 02R96 Digital Mixing Console from a Windows or Macin­tosh computer.
This
Installation Guide explains how to install Studio Manager for DM2000 and Studio
Manager for 02R96 and the necessary drivers for Windows and Macintosh computers. For information on how to use Studio Manager, refer to the
Owner’s Manual or Studio Manager for 02R96 Owner’s Manual, which are included on the
CD-ROM in PDF format. For operating information on the DM2000 or 02R96, see the
DM2000 Owner’s Manual or 02R96 Owner’s Manual respectively.

CD-ROM Contents

Windows
Getting Started
Studio Manager for DM2000
1
Folder Software Description
1,
Acroread\English
SM_\DM2000
SM_\02R96
Mididrv_ Yamaha CBX Driver
USBdrv_
USBdrv2k_
Card_
1. For details on using this software, refer to the PDF manual after installation.
2. This software is not supported by Yamaha.
Acrobat Reader
Studio Manager for DM2000
Studio Manager for 02R96
Yamaha USB MIDI Driver (Windows 98, Me)
Yamaha USB MIDI Driver (Windows 2000, XP)
Card Filer
2
1
Adobe Acrobat Reader software for viewing the PDF format manuals.
1
Yamaha Studio Manager for DM2000
1
Yamaha Studio Manager for 02R96
Yamaha serial driver. Necessary if you are con­necting to a serial port on your PC.
Yamaha USB driver. Necessary if you are con­necting to a USB port on your PC.
Yamaha utility for transferring and managing data stored on the DM2000’s SmartMedia card.
Macintosh
Folder Software Description
1,
Acroread\English
SM_\DM2000
SM_\02R96
OMS_
USBdrv_ YAMAHA USB MIDI Driver
Card_
1. For details on using this software, refer to the PDF manual after installation.
2. This software is not supported by Yamaha.
Acrobat Reader
Studio Manager for DM2000
Studio Manager for 02R96
Open Music System (OMS)
1, 2
2.3.8
OMS Setup for YAMAHA
Card Filer
2
1
Adobe Acrobat Reader software for viewing the PDF format manuals.
1
Yamaha Studio Manager for DM2000
1
Yamaha Studio Manager for 02R96
Opcode driver software for use with MIDI applications on Macintosh computers.
OMS studio setup files for use with the DM2000 and 02R96.
Yamaha USB driver. Necessary if you are con­necting to a USB port on your Macintosh com­puter.
Yamaha utility for transferring and managing data stored on the DM2000’s SmartMedia card.
Studio Manager for DM2000/02R96—Installation Guide
OS
OS
OS
OS
2
Chapter 1—Getting Started

Windows System Requirements

The system requirements of your operating system may be different to those listed here.
Studio Manager for DM2000/Studio Manager for 02R96
Computer
Memory
Hard Disk
Display
Card Filer (DM2000 only)
Computer
Memory
Hard Disk
Display
A PC with a 433 MHz or faster Intel Pentium or Celeron family processor
Windows 98SE, Me, 2000, XP Home Edition, XP Professional
128 MB or more
20 MB or more of free space
1024 x 768 pixels, 256 colors or higher 1280 x 1024, High Color 16-bit recommended (If you use display settings of 1024 x 768, turn on the Task Bar’s Auto-hide option.)
A PC with a 100 MHz or faster Intel Pentium or Celeron family processor
Windows 95, 98, 98SE, Me, NT4.0, 2000, XP Home Edition, XP Professional
8 MB or more
2 MB or more of free space
800 x 600 pixels, 256 colors or higher
Yamaha USB MIDI Driver
Computer
Memory
Hard Disk
A PC with a 166 MHz or faster Intel Pentium or Celeron family processor and a USB port
Windows 98, 98SE, Me, 2000, XP Home Edition, XP Professional
32 MB or more
2 MB or more of free space
Yamaha CBX Driver
Windows 95, 98, 98SE, Me, NT4.0, 2000, XP Home Edition, XP Professional
System requirements for software not listed here can be found on the CD-ROM.
Studio Manager for DM2000/02R96—Installation Guide
OS
OS
OS

Macintosh System Requirements

The system requirements of your operating system may be different to those listed here.
Studio Manager for DM2000/Studio Manager for 02R96
Computer
Memory
Hard Disk
Display
Other
Note: If you are using a PowerBook on battery power, open the Energy Save control panel, and in Advanced Settings, Additional Power Savings, turn off Allow processor cycling.
Card Filer (DM2000 only)
Computer
Memory
Hard Disk
Display
A Macintosh G3/233 MHz or better and a USB port
Mac OS 8.6 to 9.2.2 (Mac OS X not supported)
50 MB or more of free memory (Virtual memory must be turned off)
7 MB or more
1024 x 768 pixels, 256 colors or higher 1280 x 1024, 32,000 colors recommended
OMS 2.3.3 or later
A Macintosh computer with a PowerPC processor or better
Mac OS 7.5 to 9.2.2 (Mac OS X not supported)
8 MB or more of free memory
6 MB or more
800 x 600 pixels, 256 colors or higher
Macintosh System Requirements
3
Yamaha USB MIDI Driver
Computer
Memory
Hard Disk
System requirements for software not listed here can be found on the CD-ROM.
A Macintosh computer with a PowerPC processor or better and a USB port
Mac OS 8.6 to 9.2.2 (Mac OS X not supported)
64 MB or more (recommended: 128 MB or more)
2 MB or more
Studio Manager for DM2000/02R96—Installation Guide
4
Chapter 1—Getting Started

DM2000/02R96 Hookup

The following illustration shows the three hookup methods that can be used to connect the DM2000/02R96 to your computer: serial, USB, or MIDI.
2.
DM2000/02R96 rear panel Mac or PC
Serial1.
(Yamaha CCJ-Mac
or equivalent)
Serial cable
(Yamaha CCJ-PC2
or equivalent)
Mac serial port
PC serial port
USB
USB port
USB cable
3.
MIDI
MIDI cables
Note: Before you connect to serial or MIDI ports, turn off the DM2000/02R96 and your computer.
Configuring the DM2000/02R96
On the DM2000/02R96, use the DISPLAY ACCESS [SETUP] button to locate the MIDI/TO HOST Setup page. Under “Studio Manager,” select a port and assign an ID to the DM2000/02R96. If you are using a serial connection, set the TO HOST SERIAL options as necessary (i.e., “PC-2” for a Windows PC, or “Mac” for a Macintosh computer). Refer to the
DM2000 Owner's Manual or 02R96 Owner's Manual for more information.
MIDI interface
Studio Manager for DM2000/02R96—Installation Guide

2 Windows Installation

Acrobat Reader

To view the Studio Manager for DM2000 Owner’s Manual or Studio Manager for 02R96
Owner’s Manual,
included on the CD-ROM. If you already have this software installed, skip this section.
1
Start your computer and Windows, and insert the included CD-ROM into your computer’s CD-ROM drive.
2
On the CD-ROM, double-click the “Acroread_” folder.
This folder contains Acrobat software in several languages.
3
Double-click the folder of the language you want to install.
4
Double-click “ar500***.exe.” (“***” indicates the selected language.)
5
Follow the on-screen instructions to install the software.
For instructions on using Acrobat Reader, choose Reader Help from Acrobat Reader’s Help menu.
you’ll need to install the Adobe Acrobat Reader software, which is
Windows Installation
5

USB MIDI Driver

If you are connecting the DM2000/02R96 to a USB port on your computer, you’ll need to install the Yamaha USB driver. If you already have this software installed, skip this section.
The procedure for installing the Yamaha USB driver depends on the version of Windows that you are using.
Windows 98 & 98SE, see page 6
Windows Me, see page 8
Windows 2000, see page 9
Windows XP, see page 10
Computer
Studio
Manager
Driver
USB cable
DM2000/02R96
Studio Manager for DM2000/02R96—Installation Guide
6
Chapter 2—Windows Installation
Windows 98 & 98SE
1
Start your computer and Windows, and insert the included CD-ROM into your computer’s CD-ROM drive.
2
Turn off the DM2000/02R96 and use a USB cable to connect the USB TO HOST port on the DM2000/02R96 to a USB port on your computer.
3
Turn on the DM2000/02R96.
The Add New Hardware Wizard appears. If it doesn’t appear, try disconnecting and recon­necting the USB cable. Alternatively, open the Add New Hardware control panel.
4
Click Next.
The following window appears.
5
Select “Search for the best driver for your device (Recommended),” and then click Next.
Studio Manager for DM2000/02R96—Installation Guide
USB MIDI Driver
The following window appears.
6
Select “Specify a location,” and specify “D:\USBdrv_” (replacing “D” with the drive letter of your CD-ROM drive), and then click Next.
When the driver is located, “YAMAHA USB MIDI Driver” is displayed, as shown below.
7
7
Click Next.
Note: You may be prompted to insert your Windows CD-ROM. Do not insert it! Click OK, and in the “Copy files from” section of the subsequent dialog box, enter “D:\USBdrv_” (replac­ing “D” with the drive letter of your CD-ROM drive), and then click OK.
The driver is installed, and the following window appears when the installation is complete.
8
Click Finish, and then restart your computer.
Studio Manager for DM2000/02R96—Installation Guide
8
Chapter 2—Windows Installation
Windows Me
1 Start your computer and Windows, and insert the included CD-ROM into
your computer’s CD-ROM drive.
2 Turn off the DM2000/02R96 and use a USB cable to connect the USB TO
HOST port on the DM2000/02R96 to a USB port on your computer.
3 Turn on the DM2000/02R96.
The Add New Hardware Wizard appears. If it doesn’t appear, try disconnecting and recon­necting the USB cable. Alternatively, open the Add New Hardware control panel.
4 Select “Automatic search for a better driver (Recommended),” and then click
Next.
Windows Me should be able to locate the driver automatically, in which case you can pro­ceed to Step 5. If the driver cannot be located, select “Specify the location of the driver (Advanced),” click Next, specify your CD-ROM drive (e.g., D:\USBdrv_), and then con­tinue as prompted.
The following window appears when the installation is complete.
5 Click Finish, and then restart your computer.
Studio Manager for DM2000/02R96—Installation Guide
USB MIDI Driver 9
Windows 2000
1 Start your computer and Windows, log on as the Administrator, and then
insert the included CD-ROM into your computer’s CD-ROM drive.
2 Go to My Computer–>Control Panel–>System–>Hardware–>Driver Sign-
ing–>File Signature Verification, select “Ignore—Install all files, regardless of file signature,” and then click OK.
3 Turn off the DM2000/02R96 and use a USB cable to connect the USB TO
HOST port on the DM2000/02R96 to a USB port on your computer.
4 Turn on the DM2000/02R96.
The Found New Hardware Wizard appears.
5 Click Next.
6 Select “Search for a suitable driver for my device (Recommended),” and then
click Next.
7 In the subsequent window, select “CD-ROM drives” only, and then click Next.
Note: You may be prompted to insert your Windows CD-ROM. Do not insert it! Click OK, and in the “Copy files from” section of the subsequent dialog box, enter “D:\USBdrv2k_” (replacing “D” with the drive letter of your CD-ROM drive), and then click OK.
The driver is installed, and the message “Completing the Found New Hardware Wizard” appears.
8 Click Finish, and then restart your computer.
Studio Manager for DM2000/02R96—Installation Guide
10 Chapter 2—Windows Installation
Windows XP
1 Start your computer and Windows, and insert the included CD-ROM into
your computer’s CD-ROM drive.
2 Click the Start button, and then click Control Panel.
If the Control Panel window appears as shown below, click “Switch to Classic View” on the left side of the window in order to see all the control panels.
3 Go to System Hardware–>Driver signatures–>Driver signature options,
select “Ignore—Install software without asking for confirmation,” and then click OK.
4 Click OK to close the System Properties window, and then click the Close but-
ton to close the Control Panel window.
5 Turn off the DM2000/02R96 and use a USB cable to connect the USB TO
HOST port on the DM2000/02R96 to a USB port on your computer.
6 Turn on the DM2000/02R96.
The Found New Hardware Wizard appears.
7 Select “Install software automatically (recommended) (I),” and then click
Next.
The driver is installed, and the message “Completing the Found New Hardware Wizard” appears.
8 Click Finish, and then restart your computer.
Studio Manager for DM2000/02R96—Installation Guide

Yamaha CBX Driver

If you are connecting the DM2000/02R96 to a serial port on your computer, you’ll need to install the Yamaha CBX driver. If you already have this software installed, skip this section.
1 Double-click the “Mididrv_” folder on the CD-ROM.
2 Double-click “Setup.exe.”
3 Follow the on-screen instructions to install the software.

Studio Manager for DM2000

1 Double-click the “SM_” folder on the CD-ROM.
2 Double-click the “DM2000” folder.
3 Double-click “Setup.exe.”
4 Follow the on-screen instructions to install the software.

Studio Manager for 02R96

1 Double-click the “SM_” folder on the CD-ROM.
Yamaha CBX Driver 11
2 Double-click the “02R96” folder.
3 Double-click “Setup.exe.”
4 Follow the on-screen instructions to install the software.

Card Filer (DM2000 only)

1 Double-click the “Card_” folder on the CD-ROM.
2 Double-click “Setup.exe.”
3 Follow the on-screen instructions to install the software.
See the Card Filer Manual PDF, which is installed in the same folder as Card Filer, for infor­mation on using Card Filer.
Studio Manager for DM2000/02R96—Installation Guide
12 Chapter 3—Macintosh Installation

3 Macintosh Installation

Acrobat Reader

To view the Studio Manager for DM2000 Owner’s Manual or Studio Manager for 02R96 Owner’s Manual, you’ll need to install the Adobe Acrobat Reader software, which is
included on the CD-ROM. If you already have this software installed, skip this section.
1 Start your Macintosh, and insert the included CD-ROM into your computer’s
CD-ROM drive.
2 Double-click the “Acroread_” folder on the CD-ROM.
This folder contains Acrobat software in several languages.
3 Double-click the folder of the language you want to install.
4 Double-click “Reader Installer.”
(The name of the installer depends on the language selected.)
5 Follow the on-screen instructions to install the software.
For instructions on using Acrobat Reader, choose Reader Guide from Acrobat Reader’s Help menu.

OMS (Open Music System)

Studio Manager requires OMS 2.3.3 or later in order to work on Macintosh computers. OMS 2.3.8 is included on the CD-ROM. If you already have this software installed, skip this section.
1 Start your Macintosh, and insert the included CD-ROM into your computer’s
CD-ROM drive.
2 Double-click the “OMS_” folder on the CD-ROM.
3 Double-click “Install OMS 2.3.8.”
4 Follow the on-screen instructions to install the software.
5 When the installation is complete, click Restart.
Note: Once the installation is complete, you may receive an error message warning that the installer did not quit. In this case, choose Quit from the File menu to quit the installer, then restart your computer.
6 Copy the “OMS_2.3_Mac.pdf” from the “OMS_” folder on the CD-ROM to
the “Opcode:OMS Applications” folder on your hard disk.
This file contains information on using and configuring OMS.
Studio Manager for DM2000/02R96—Installation Guide

USB MIDI Driver

If you are connecting the DM2000/02R96 to a USB port on your computer, you’ll need to install the Yamaha USB driver. If you already have this software installed, skip this section.
USB MIDI Driver 13
Computer
Studio
Manager
OMS
USB cable
Driver
DM2000/02R96
1 Start your Macintosh, and insert the included CD-ROM into your computer’s
CD-ROM drive.
2 Double-click the “USBdrv_” folder on the CD-ROM.
3 Double-click “Install USB MIDI Driver.”
The Install USB MIDI Driver window appears, as shown below.
Normally there’s no need to set the Install Location, because the startup disk is selected by default. To select another disk, click the Switch Disk button. Although you can choose a folder from the pop-up menu, the files are installed in the specified disk’s System Folder regardless, so you can ignore that setting.
4 Click Install, and follow the on-screen instructions to install the software.
5 When the installation is complete, click Restart.

Studio Manager for DM2000

1 Start your Macintosh, and insert the included CD-ROM into your computer’s
CD-ROM drive.
2 Double-click the “SM_” folder on the CD-ROM.
3 Double-click the “DM2000” folder.
4 Double-click “Install Studio Manager.”
5 Follow the on-screen instructions to install the software.
Studio Manager for DM2000/02R96—Installation Guide
14 Chapter 3—Macintosh Installation

Studio Manager for 02R96

1 Start your Macintosh, and insert the included CD-ROM into your computer’s
CD-ROM drive.
2 Double-click the “SM_” folder on the CD-ROM.
3 Double-click the “02R96” folder.
4 Double-click “Install Studio Manager.”
5 Follow the on-screen instructions to install the software.

Card Filer (DM2000 only)

1 Start your Macintosh, and insert the included CD-ROM into your computer’s
CD-ROM drive.
2 Double-click the “Card_” folder on the CD-ROM.
3 Double-click “Install Card Filer.”
4 Follow the on-screen instructions to install the software.
See the “CardFilerManual.pdf,” which is installed in the same folder as Card Filer, for infor­mation on using Card Filer.

Setting up OMS

The “OMS Setup for YAMAHA” folder on the included CD-ROM contains OMS studio setup files for use with the DM2000 and 02R96.
1 Turn off the DM2000/02R96 and use a USB cable to connect the USB TO
HOST port on the DM2000/02R96 to a USB port on your computer.
If you are connecting to the SERIAL TO HOST port, use a serial cable to connect the Printer or Modem port on your computer.
2 Turn on the DM2000/02R96.
3 Start your Macintosh, and insert the included CD-ROM into your computer’s
CD-ROM drive.
4 Open the “OMS_” folder on the CD-ROM, and then open the “OMS Setup
for YAMAHA” folder.
This folder contains six OMS studio setup files.
DM2000-USB
DM2000-Modem
DM2000-Printer
02R96-USB
02R96-Modem
02R96-Printer
5 Copy the required file to your computer’s hard disk, and then double-click it.
Studio Manager for DM2000/02R96—Installation Guide
Setting up OMS 15
OMS Setup starts and the Studio Setup file window appears, as shown by this example, which is the DM2000-USB studio setup.
The symbol next to the setup name in the title bar indicates that this is the current Studio Setup.
6 If the symbol is not displayed, choose Make
Current from the File menu, and then save the setup.
Note: If you are using the Modem or Printer port, go to OMS Setup Preferences and turn off “Use Apple SerialDMA driver when available.”
After completing the above setup, the DM2000 will be the only MIDI device in the current OMS studio setup. In order to use other MIDI devices, or to add an additional DM2000, you must create a new studio setup. See the “OMS_2.3_Mac.pdf” for more information.
Studio Manager for DM2000/02R96—Installation Guide
16 Chapter 4—Troubleshooting

4 Troubleshooting

Cannot control the DM2000/02R96 via USB
Have you installed the Yamaha USB MIDI driver (Windows page 5, Mac page 13)?
Is the USB cable connected correctly (page 4)?
Is the DM2000/02R96 configured correctly (page 4)?
Is Studio Manager set to the correct ID? (see the Studio Manager documentation)
Macintosh: Is OMS configured correctly (page 14)? On some systems, the included OMS studio setup files may not work correctly. In this case, you must create a new studio setup. See the “OMS_2.3_Mac.pdf” for more information.
Cannot install the Yamaha USB MIDI Driver
Is the USB cable connected correctly (page 4)?
Try disconnecting the USB cable, and then reconnecting it.
Windows: Is USB enabled? When the DM2000/02R96 is connected to your computer for the first time, if the Add New Hardware Wizard doesn’t appear, it may be because your com­puter’s USB controller is disabled. To check this, open the System control panel, click the Device Manager tab, and check for any crosses (x) or exclamation marks (!) next to the “Universal Serial Bus controllers” and “USB Root Hub” items. If these items do have these marks next to them, your USB controller is disabled. For information on enabling your USB controller, refer to your computer’s documentation.
Windows: If for some reason installation of the Yamaha USB Driver fails, the DM2000/02R96 may be registered as an unknown device and you may not be able to rein­stall the driver until the unknown device is deleted. In this case, open the System control panel, click the Device Manager tab, and select the “View devices by connection” option. If an item called “Other devices” appears in the list, click it. If there’s an item called “Unknown device,” select it and then click the Remove button. Disconnect the USB cable, then recon­nect it, and now try installing the driver again.
OMS stops working after installing the Yamaha USB MIDI Driver
Macintosh: The Yamaha USB MIDI Driver supports Mac OS 8.6 through 9.2.2. If you install it on a computer that is running an earlier version of the Mac OS, OMS will not work cor­rectly. In this case you should remove the Yamaha USB MIDI Driver as explained below.
How to remove & reinstall the Yamaha USB MIDI Driver
Windows 98/Me: Presuming that the Yamaha USB MIDI Driver was installed successfully, and that the DM2000/02R96 has been recognized correctly, the driver can be removed from your computer as follows. Open the System control panel, click the Device Manager tab, select the “YAMAHA USB MIDI Driver,” and then click the Remove button. After deleting the following files, disconnect the USB cable, reconnect it, and then reinstall the driver again.
Windows\Inf\Other\YAMAHADM2000.INF (or YAMAHA02R96.INF) Windows\System\Xgusb.drv Windows\System\Ymidusb.sys
Macintosh: The driver can be removed from your computer by deleting the following files, after which you should restart your computer, reinstall the driver, and then set up OMS.
Studio Manager for DM2000/02R96—Installation Guide
Troubleshooting 17
System Folder:Control Panels:YAMAHA USB MIDI Patch System Folder:Extensions:USB YAMAHA MIDI Diver System Folder:OMS Folder:YAMAHA USB MIDI OMS Driver
Improving performance
If your computer seems unresponsive, make sure it satisfies the system requirements (Win­dows page 2, Mac page 3).
Quit any other applications that you are not using.
Macintosh: Try turning off virtual memory and AppleTalk.
Cannot suspend or resume your computer
Windows: Suspend will not work if there are any MIDI applications open.
Windows 2000: Depending on the USB controller, etc., on some systems, suspend and resume may not work properly. If the DM2000/02R96 stops responding, try disconnecting and reconnecting the USB cable.
Studio Manager for DM2000/02R96—Installation Guide
18
Software Licensing Agreement
The following is a legal agreement between you, the end user, and Yamaha Corporation (“Yamaha”). The enclosed Yamaha software program is licensed by Yamaha to the original purchaser for use only on the terms set forth herein. Please read this licensing agreement with care. Opening this package indicates that you accept all terms outlined herein. If you do not agree to the terms, return this package unopened to Yamaha for a full refund.
GRANT OF LICENSE AND COPYRIGHT: Yamaha grants you, the original purchaser, the right to use one copy of the enclosed software program and data (“SOFTWARE”) on a single-user computer system. You may not use it on more than one computer or computer terminal. The SOFTWARE is owned by Yamaha and is protected by Japanese copyright laws and all applicable international treaty provisions. You are entitled to claim ownership of the media in which the SOFTWARE is included. Therefore, you must treat the SOFTWARE like any other copyrighted materials.
RESTRICTIONS: The SOFTWARE program is copyrighted. You may not engage in reverse engineering or reproduction of the SOFTWARE by other conceivable methods. You may not reproduce, modify, change, rent, lease, resell, or distribute the SOFTWARE in whole or in part, or create derivative works from the SOFTWARE. You may not transmit or network the SOFTWARE with other computers. You may transfer ownership of the SOFT­WARE and the accompanying written materials on a permanent basis provided that you retain no copies and the recipient agrees to the terms of the licensing agreement.
TERMINATION: The licensing condition of the software program becomes effective on the day that you receive the SOFTWARE. If any one of the copyright laws or clauses of the licensing conditions is violated, the licensing agreement shall be terminated automatically without notice from Yamaha. In this case, you must destroy the licensed SOFTWARE and its copies immediately.
PRODUCT WARRANTY: Yamaha warrants to the original purchaser that if the SOFT­WARE, when used in normal conditions, will not perform the functions described in the manual provided by Yamaha, the sole remedy will be that Yamaha will replace any media which proves defective in materials or workmanship on an exchange basis without charge. Except as expressly set forth above, the SOFTWARE is provided “as is,” and no other war­ranties, either expressed or implied, are made with respect to this software, including, with­out limitation the implied warranties of merchantability and fitness for a particular purpose.
LIMITED LIABILITY: Your sole remedies and Yamaha’s entire liability are as set forth above. In no event will Yamaha be liable to you or any other person for any damages, includ­ing without limitation any incidental or consequential damages, expenses, lost profits, lost savings or other damages arising out of the use or inability to use such SOFTWARE even if Yamaha or an authorized dealer has been advised of the possibility of such damages, or for any claim by any other party.
GENERAL: This license agreement shall be interpreted according to and governed by Jap­anese laws.
Studio Manager for DM2000/02R96—Installation Guide
V954150 R0 1 IP 24 Pro Audio & Digital Musical Instrument Division
02 04 1230 AP Printed in Japan
YAMAHA CORPORATION
P.O. Box 3, Hamamatsu, 430-8651, Japan
documentation manual, user maintenance, brochure, user reference, pdf manual
This file has been downloaded from:
User Manual and User Guide for many equipments like mobile phones, photo cameras, monther board, monitors, software, tv, dvd, and othes..
Manual users, user manuals, user guide manual, owners manual, instruction manual, manual owner, manual owner's, manual guide,
manual operation, operating manual, user's manual, operating instructions, manual operators, manual operator, manual product,
Loading...