Yamaha Audio 01V96 User Manual

Owner’s Manual

Keep This Manual For Future Reference.

E

FCC INFORMATION (U.S.A.)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST
be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with
these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with
other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may
cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all
installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the
problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. Utilize power outlets that are on
different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in
is 300 ohm ribbon lead, change the lead-in to coaxial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer
authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic Service
Division, 6600 Orangethorpe Ave, Buena Park, CA 90620

The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.

WARNING: THIS APPARATUS MUST BE EARTHED

IMPORTANT

THE WIRES IN THIS MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:

GREEN-AND-YELLOW : EARTH

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this apparatus may
not correspond with the coloured markings identifying the terminals in
your plug, proceed as follows:

The wire which is coloured GREEN and YELLOW must be
connected to the terminal in the plug which is marked by the letter E
or by the safety earth symbol or coloured GREEN and YELLOW.

The wire which is coloured BLUE must be connected to the terminal
which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the
terminal which is marked with the letter L or coloured RED.

* This applies only to products distributed by YAMAHA KEMBLE

MUSIC (U.K.) LTD.

NEDERLAND THE NETHERLANDS

● Dit apparaat bevat een lithium batterij voor geheugen
back-up.

ADVARSEL!
Lithiumbatteri—Eksplosionsfare ved fejlagtig
håndtering. Udskiftning må kun ske med batteri
af samme fabrikat og type. Levér det brugte
batteri tilbage til leverandoren.

VARNING
Explosionsfara vid felaktigt batteribyte. Använd
samma batterityp eller en ekvivalent typ som
rekommenderas av apparattillverkaren.
Kassera använt batteri enligt fabrikantens
instruktion.

VAROITUS
Paristo voi räjähtää, jos se on virheellisesti
asennettu. Vaihda paristo ainoastaan
laitevalmistajan suosittelemaan tyyppiin. Hävitä
käytetty paristo valmistajan ohjeiden
mukaisesti.

● This apparatus contains a lithium battery for memory
back-up.

● Raadpleeg uw leverancier over de verwijdering van de
batterij op het moment dat u het apparaat ann het einde
van de levensduur afdankt of de volgende Yamaha Service
Afdeiing:

Yamaha Music Nederland Service Afdeiing
Kanaalweg 18-G, 3526 KL UTRECHT
Te l. 030-2828425

● Gooi de batterij niet weg, maar lever hem in als KCA.

● For the removal of the battery at the moment of the
disposal at the end of the service life please consult your
retailer or Yamaha Service Center as follows:

Yamaha Music Nederland Service Center
Address: Kanaalweg 18-G, 3526 KL

UTRECHT

Te l: 030-2828425

● Do not throw away the battery. Instead, hand it in as small
chemical waste.

• Explanation of Graphical Symbols

The lightning flash with arrowhead symbol

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

The above warning is located on the rear
of the unit

within an equilateral triangle is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.

The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and mainte­nance (servicing) instructions in the literature
accompanying the product.

IMPORTANT SAFETY INSTRUCTIONS

1 Read these instructions.
2Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in

accordance with the manufacturer’s instruc­tions.

8 Do not install near any heat sources such as

radiators, heat registers, stoves, or other appa­ratus (including amplifiers) that produce heat.

9 Do not defeat the safety purpose of the polar-

ized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A
grounding type plug has two blades and a third
grounding prong. The wide blade or the third
prong are provided for your safety. If the pro­vided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete
outlet.

10 Protect the power cord from being walked on or

pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.

11 Only use attachments/accessories specified by

the manufacturer.

12 Use only with the cart, stand,

tripod, bracket, or table spec­ified by the manufacturer, or
sold with the apparatus.
When a cart is used, use cau­tion when moving the cart/
apparatus combination to
avoid injury from tip-over.

13 Unplug this apparatus during lightning storms

or when unused for long periods of time.

14 Refer all servicing to qualified service person-

nel. Servicing is required when the apparatus
has been damaged in any way, such as power­supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or mois­ture, does not operate normally, or has been
dropped.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

iv

Important Information

Important Information

Warnings

•Connect this unit’s power cord only to an AC outlet of the type stated in this Owner’s Man­ual or as marked on the unit. Failure to do so is a fire and electrical shock hazard.

•Do not allow water to enter this unit or allow the unit to become wet. Fire or electrical shock
may result.

•Do not place heavy objects, including this unit, on top of the power cord. A damaged power
cord is a fire and electrical shock hazard. In particular, be careful not to place heavy objects
on a power cord covered by a carpet.

•Do not place a container with liquid or small metal objects on top of this unit. Liquid or
metal objects inside this unit are a fire and electrical shock hazard.

•Do not scratch, bend, twist, pull, or heat the power cord. A damaged power cord is a fire
and electrical shock hazard.

•Do not remove the unit’s cover. You could receive an electrical shock. If you think internal
inspection, maintenance, or repair is necessary, contact your dealer.

•Do not modify the unit. Doing so is a fire and electrical shock hazard.

•If lightning begins to occur, turn off the power switch of the unit as soon as possible, and
unplug the power cable plug from the electrical outlet.

•If there is a possibility of lightning, do not touch the power cable plug if it is still connected.
Doing so may be an electrical shock hazard.

•Use only the included power cord for this unit. Using other types may be a fire and electrical
shock hazard.

•This unit has a slot for installing mini-YGDAI cards. For technical reasons, certain card
combinations are not supported. Before installing any cards, check the Yamaha web site to
if your card is compatible. Installing cards that are not endorsed by Yamaha may cause elec­trical shock, fire, or damage to the unit.

•If the power cord is damaged (i.e., cut or a bare wire is exposed), ask your dealer for a
replacement. Using the unit with a damaged power cord is a fire and electrical shock hazard.

•If you notice any abnormality, such as smoke, odor, or noise, or if a foreign object or liquid
gets inside the unit, turn it off immediately. Remove the power cord from the AC outlet.
Consult your dealer for repair. Using the unit in this condition is a fire and electrical shock
hazard.

• Should this unit be dropped or the cabinet be damaged, turn the power switch off, remove
the power plug from the AC outlet, and contact your dealer. If you continue using the unit
without heeding this instruction, fire or electrical shock may result.

Cautions

•Keep this unit away from the following locations:
—Locations exposed to oil splashes or steam, such as near cooking stoves, humidifiers, etc.
—Unstable surfaces, such as a wobbly table or slope.
—Locations exposed to excessive heat, such as inside a car with all the windows closed, or

places that receive direct sunlight.

—Locations subject to excessive humidity or dust accumulation.

•Hold the power cord plug when disconnecting it from an AC outlet. Never pull the cord. A
damaged power cord is a potential fire and electrical shock hazard.

•Do not touch the power plug with wet hands. Doing so is a potential electrical shock hazard.

01V96—Owner’s Manual

•This unit has ventilation holes along the top, front, rear, and sides to prevent the internal
temperature from rising too high. Do not block them. Blocked ventilation holes are a fire
hazard. In particular, do not operate the unit while it’s on its side, is upside down, or while
it’s covered with a cloth or dust sheet.

•This unit is equipped with a dedicated ground connection to prevent electrical shock.
Before connecting the power plug to an AC outlet, be sure to ground the unit.

•To relocate the unit, turn the power switch off, remove the power plug from the AC outlet,
and remove all connecting cables. Damaged cables may cause fire or electrical shock.

•If you know you will not use this unit for a long period of time, such as when going on vaca­tion, remove the power plug from the AC outlet. Leaving it connected is a potential fire haz­ard.

Operating Notes

• XLR-type connectors are wired as follows: pin 1–ground, pin 2–hot (+), and pin 3–cold (–).

•Insert TRS phone jacks are wired as follows: sleeve–ground, tip–send, and ring–return.

•The performance of components with moving contacts, such switches, rotary controls, fad­ers, and connectors, deteriorates over time. The rate of deterioration depends on the oper­ating environment and is unavoidable. Consult your dealer about replacing defective
components.

•Using a mobile telephone near this unit may induce noise. If noise occurs, use the telephone
away from the unit.

•If the message “WARNING Low Battery!” appears when you turn on this unit, contact your
dealer as soon as possible about replacing the internal data backup battery. The unit will still
operate correctly, but data other than the presets will be lost.

•Before replacing the batteries, back up your data to a memory card, or another unit by using
MIDI Bulk Dump.

•The digital circuits of this unit may induce a slight noise into nearby radios and TVs. If noise
occurs, relocate the affected equipment.

•When you change the wordclock settings on any device in your digital audio system, some
devices may output noise, so turn down your power amps beforehand, otherwise your
speakers may be damaged.

Operating Notes

v

Interference

This unit uses high-frequency digital circuits that may cause interference on radio and tele­vision equipment located nearby. If interference is a problem, relocate the affected equip­ment. Using a mobile telephone near the unit may induce noise. In this case use the
telephone away from the unit.

Exclusion of Certain Responsibility

Manufacturer, importer, or dealer shall not be liable for any incidental damages including
personal injury or any other damages caused by improper use or operation of this unit.

01V96—Owner’s Manual

vi

Important Information

Trademarks

Copyright

ADAT MultiChannel Optical Digital Interface is a trademark and ADAT and Alesis are reg­istered trademarks of Alesis Corporation. Apogee is a trademark of Apogee Electronics, Inc.
Apple, Mac, and Power Macintosh are registered trademarks and Mac OS is a trademark of
Apple Corporation, Inc. HUI is a trademark of Mackie Designs, Inc. Intel and Pentium are
registered trademarks of Intel Corporation. Nuendo is a registered trademark of Steinberg
Media Technologies AG. Pro Tools is a trademark or registered trademark of Digidesign
and/or Avid Technology, Inc. Tascam Digital Interface is a trademark and Tascam and Teac
are registered trademarks of Teac Corporation. Microsoft and Windows are registered
trademarks of Microsoft Corporation, Inc. Waves is a trademark of Waves, Inc. Yamaha is a
trademark of Yamaha Corporation. All other trademarks are the property of their respective
holders and are hereby acknowledged.

No part of this unit, its software, or this Owner’s Manual may be reproduced or distributed
in any form or by any means without the prior written authorization of Yamaha Corpora­tion.

© 2003 Yamaha Corporation. All rights reserved.

Yamaha Web Site

Further information about the 01V96, related products, and other Yamaha professional
audio equipment is available on the Yamaha Professional Audio Web site at:
<http://www.yamahaproaudio.com/>.

Package Contents

• 01V96 Digital Mixing Console

• CD-ROM

•Power cord

•This manual

•Studio Manager Installation Guide

Optional Extras

• RK1 Rack Mount Kit

• mini YGDAI I/O cards

01V96—Owner’s Manual

About this Owner’s Manual

This Owner’s Manual explains how to operate the 01V96 Digital Mixing Console.
The Table of Contents can help you to familiarize yourself with the manual’s organization

and to locate tasks and topics. The index can help you locate specific information.
Before diving in, it’s recommend that you read the “Operating Basics” chapter, starting on

page 27.
Each chapter in this manual discusses a specific section or function of the 01V96. The Input

and Output Channels are explained in the following chapters: “Input Channels,” “Bus
Outs,” and “Aux Outs.” Where possible, these chapters have been organized in order of sig­nal flow, from input to output.

Conventions Used in this Manual

The 01V96 features two types of buttons: physical buttons that you can press (e.g., ENTER
and DISPLAY) and buttons that appear on the display pages. References to physical buttons
are enclosed in square brackets, for example, “press the [ENTER] button.”

References to display page buttons are not emphasized, for example, “move the cursor to the
ON button.”

You can select display pages by using the [DISPLAY] buttons or the Left Tab Scroll, Right
Tab Scroll, and F1–4 buttons below the display. In order to simplify explanations, the pro­cedures reference only the [DISPLAY] button method.

See “Selecting Display Pages” on page 28 for details on all the ways in which you can select
pages.

About this Owner’s Manual

vii

Installing the 01V96

This unit should be placed on a strong and stable surface, that complies with the warnings
and cautions listed in the previous sections.

Always turn the power off when the instrument is not in use.

The illustrations and LCD screens as shown in this owner’s manual are for instructional
purposes only, and may appear somewhat different from those on your instrument.

Copying of the commercially available music sequence data and/or digital audio files is
strictly prohibited except for your personal use.

01V96—Owner’s Manual

8

Contents

Contents

1 Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2 Control Surface & Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Control Surface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Installing an Optional Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

3 Operating Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

About the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Selecting Display Pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Display Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Selecting Layers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Selecting Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Selecting Fader Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Metering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

4 Connections and Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Wordclock Connections and Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Input and Output Patching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

5 Tutorial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Connections and Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Initial Track Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Overdubbing to Other Tracks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Mixing Recorded Tracks into Stereo (Mixdown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

6 Analog I/O & Digital I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Analog Inputs & Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Digital Inputs & Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Converting Sampling Rates of Signals Received at I/O Card Inputs . . . . . . . . . . 72

Monitoring Digital Input Channel Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Dithering Digital Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Setting the Transfer Format for Higher Sampling Rates . . . . . . . . . . . . . . . . . . . . . . . 75

7 Input Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

About Input Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Setting the Input Channels from the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Setting the Input Channels from the Control Surface . . . . . . . . . . . . . . . . . . . . . . . . . 90

Pairing Input Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

Naming Input Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

8 Bus Outs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

About Stereo Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

Bus Out 1–8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98

Setting the Stereo Out and Bus Out 1–8 from the Display . . . . . . . . . . . . . . . . . . . . . 99

Setting the Stereo Out and Bus Out 1–8 from the Control Surface . . . . . . . . . . . . . . 104

Pairing Buses or Aux Sends . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105

Attenuating Output Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106

Naming the Stereo Out and Bus Outs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107

9 Aux Outs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109

Aux Out 1–8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109

Setting Aux Out 1–8 from the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110

Viewing Aux Out settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

Setting Aux Out 1–8 from the Control Surface . . . . . . . . . . . . . . . . . . . . . . . . . . . 113

01V96—Owner’s Manual

Contents

Setting Aux Send Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113

Viewing Aux Send Settings for Multiple Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117

Panning Aux Sends . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119

Copying Channel Fader Positions to Aux Sends . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120

10 Input & Output Patching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121

Input Patching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121

Output Patching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123

Patching Direct Outs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125

Insert Patching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127

11 Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131

Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131

Monitor and Solo Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132

Using the Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133

Using the Solo Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134

12 Surround Pan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135

Using Surround Pan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135

Setting Up and Selecting Surround Pan Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . 136

Surround Panning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141

13 Grouping Channels & Linking Parameters . . . . . . . . . . . . . . . . . . 147

Grouping & Linking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147

Using Fader Groups and Mute Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148

Linking EQ and Compressor Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150

9

14 Internal Effects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153

About the Internal Effects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153

Using Effects Processors via Aux Sends . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154

Inserting the Internal Effects into Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156

Editing Effects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157

About Plug-Ins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159

15 Scene Memories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161

About Scene Memories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161

What is Stored in a Scene? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161

About Scene Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162

Storing & Recalling Scenes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163

Auto Scene Memory Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165

Fading Scenes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166

Recalling Scenes Safely . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168

Sorting Scenes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169

16 Libraries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171

About the Libraries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171

General Library Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171

Using Libraries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173

17 Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185

About Remote Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185

Pro Tools Remote Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186

Nuendo Remote Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202

Other DAW Remote Layers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202

MIDI Remote Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203

Machine Control Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208

01V96—Owner’s Manual

10

Contents

18 MIDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211

MIDI & the 01V96 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211

MIDI Port Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212

Assigning Scenes to Program Changes for Remote Recall . . . . . . . . . . . . . . . . . . 215

Assigning Parameters to Control Changes for Real-time Control . . . . . . . . . . . . 216

Controlling Parameters by Using Parameter Changes . . . . . . . . . . . . . . . . . . . . . 221

Transmitting Parameter Settings via MIDI (Bulk Dump) . . . . . . . . . . . . . . . . . . . . . . 222

19 Other Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225

Changing the Input and Output Channel Names . . . . . . . . . . . . . . . . . . . . . . . . . 225

Setting Preferences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 226

Creating a Custom Layer by Combining Channels (User Assignable Layer) . . . 229

Using the Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230

Using the User Defined Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 231

Using Operation Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233

Cascading Consoles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234

Checking the Battery and the System Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 238

Initializing the 01V96 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 239

Calibrating the Faders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240

Appendix A: Parameter Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 241

USER DEFINED KEYS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 241

USER DEFINED KEYS Initial Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243

Input Patch Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243

Initial Input Patch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 245

Output Patch Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 247

Initial Output Patch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 249

User Defined Remote Layer Initial Bank Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250

Effects Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 254

Preset EQ Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274

Preset Gate Parameters (fs = 44.1 kHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 278

Preset Compressor Parameters (fs = 44.1 kHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . 278

Appendix B: Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283

General Spec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283

Libraries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 288

Analog Input Spec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 289

Analog Output Specs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 289

Digital Input Spec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 290

Digital Output Spec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 290

I/O SLOT Spec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 290

CONTROL I/O Spec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291

Appendix C: MIDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 292

Scene Memory to Program Change Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 292

Initial Parameter to Control Change Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 293

MIDI Data Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309

Appendix D: Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 323

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 324

01V96—Owner’s Manual

■

■

■

1 Welcome

Thank you for choosing the Yamaha 01V96 Digital Mixing Console.
The compact 01V96 Digital Console features 24-bit/96 kHz digital audio processing with-

out compromise, as well as 40-channel simultaneous mixing. The 01V96 covers a broad
range of needs and applications, including multi-track recording, 2-channel mixdown, and
cutting-edge surround sound production. This integrated, comprehensive audio system
features remote control function for DAWs (Digital Audio Workstations) as popularized by
the DM2000 and 02R96 Digital Mixing Consoles.

The 01V96 offers the following features:

Hardware Features

• 100-mm motorized faders x 17

•Faders can set levels for Input Channels, Aux send levels, and Bus Outs.

•Four selectable software layers determine the function of channel faders.

• 320 x 240 dot LCD display

•Buttons and controls in the SELECTED CHANNEL section enable direct editing of

channel EQ parameters.

•8 USER-DEFINED KEYS enable you to assign functions to control 01V96 internal

parameters.

•ADAT optical connectors

•Expansion slot for optional digital I/O, AD, and DA cards.

Welcome

11

1

Welcome

Sonic Specifications

• Linear 24-bit, 128-times oversampling A/D converters

• Linear 24-bit, 128-times oversampling D/A converters

• 20 Hz through 40 kHz frequency response at 96 kHz sampling rate.

• 106 dB typical dynamic range

• 32-bit internal signal processing (58-bit accumulator)

Inputs and Outputs

• 12 mic/line inputs with switchable +48 V phantom power and 4 line inputs

• 12 analog inserts

•Any Bus Outs or Channel Inserts can be routed to four Omni Outs.

•Individual outputs for Stereo Out and Monitor Out

•Analog 2TR In and Out for use with Tape In and Out signals

•An optional card installed in the slot permits a maximum of 16 inputs/outputs.

•Digital 2TR In and Out for consumer-format digital audio signals

•Double Channel support for recording and playing at 88.2/96 kHz on 44.1/48 kHz leg-

acy multi-track digital recorders.

•You can cascade two 01V96s while remaining in the digital domain.

•Input patches enable assignment of input signals to desired signal paths.

•Output patches enable assignment of Bus Out signals and Input Channel Direct Outs to

desired output jacks.

01V96—Owner’s Manual

■

■

■

■

■

12

Chapter 1—Welcome

Channel Configuration

• 32 Input Channels and four ST IN channels can be mixed at a time. Group multiple
channels and pair channels for stereo.

•Eight Bus Outs and eight Aux Sends. Bus Outs 1-8 can be routed to Stereo Buses for use
as Group Buses.

•Channel library for storing and recalling the channel settings for each Input Channel
and Output Channel

•Four-band EQ on each channel

•Dynamics processors on all channels (excluding ST IN channels)

•Dynamics processor settings and EQ settings can be stored in libraries and recalled.

Effects

•Four high-quality multi-channel effects (Apply effects via Aux Sends or Channel
Inserts)

• Effect library for storing and recalling effect settings.

Scene Memory

•Scene memories for storing and recalling mix settings as Scenes

Surround Sound

•Supports 3-1, 5.1, and 6.1 channel surround sound production

•Surround channel outputs can be assigned to suit connected devices.

Remote Control

•Control and manage your 01V96 from your Mac or PC using bundled Studio Manager
software.

•Remote Layer for remote control of Pro Tools, Nuendo, and other DAWs that support
the Pro Tools protocol

•Control an external recorder via MMC commands.

■ MIDI

•Equipped with MIDI ports and a USB port for computer connection

•Scene recall and mix parameter changes via MIDI

01V96—Owner’s Manual

Control Surface & Rear Panel 13

SOLO SOLO

ON ON

SOLOONSOLOONSOLOONSOLOONSOLOONSOLOONSOLOONSOLOONSOLOONSOLOONSOLOONSOLOONSOLOONSOLO

ON

SOLOONSOLO

ONON

PEAK

SIGNAL

PEAK

SIGNAL

PEAK
SIGNAL

PEAK
SIGNAL

PEAK
SIGNAL

PEAK
SIGNAL

PEAK
SIGNAL

PEAK
SIGNAL

PEAK
SIGNAL

PEAK
SIGNAL

PEAK
SIGNAL

PEAK
SIGNAL

PEAK
SIGNAL

PEAK
SIGNAL

1-16 17-32 MASTER REMOTE

LAYER

SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SELSEL

ST IN

ENTER

EQUALIZER

HIGH

HIGH-MID

LOW-MID

LOW

Q

FREQUENCY

GAIN

STEREO

SELECTED CHANNEL

PAN

DEC INC

SOLO CLEAR

RECALL

STORE

SCENE MEMORY

PHONES

MONITOR

OUT

MONITOR
2TR IN

CH15

/

16

2TR IN

LEVEL

PHONES

LEVEL

0

10

0

10

+4

-26

GAIN

+4

-26

GAIN

+4

-26

GAIN

GAIN

+4

-26

GAIN

20dB

-16

-60

GAIN

20dB

-16

-60

GAIN

20dB20dB20dB20dB20dB20dB20dB20dB20dB20dB

-16

-60

GAIN

-16

-60

GAIN

-16

-60

GAIN

-16

-60

GAIN

-16

-60

GAIN

-16

-60

GAIN

-16

-60

GAIN

-16

-60

GAIN

-16

-60

GAIN

-16

-60

PAD

FADER MODE

DISPLAY ACCESS

AUX 1

AUX 1 AUX 2 AUX 3 AUX 4 AUX 5 AUX 6 AUX 7 AUX 8 BUS 1 BUS 2 BUS 3 BUS 4 BUS 5 BUS 6 BUS 7 BUS 8

AUX 2 AUX 3 AUX 4

AUX 8AUX 7AUX 6AUX 5

HOME (METER)

DYNAMICS

EQ EFFECT VIEW

PATCH

UTILITYMIDISCENE

DIO/SETUP

/ INSERT/

DELAY

PAN/

ROUTING

PAIR/

GROUP

ABABABABABABABABABABABA

B

16

1513

121110987643215

14

INSERT I

/

O INSERT I/O INSERT I/O INSERT I/O INSERT I/O INSERT I/O INSERT I/O INSERT I/O INSERT I/O INSERT I/OINSERT I/O INSERT I/O

L

R

IN OUT

2TR

-10dBV (UNBAL)

PHANTOM +48V

CH9-12CH5-8CH1-4

INPUT

(BAL)

INSERT

OUTIN

(UNBAL)

ST IN 1 ST IN 2

USER DEFINED

KEYS

12

34

56

78

55

5

+10

5

1010

10

1515

15

2020

20

303030

30

4040

40

5050

50

6060

7070

20

30

40

40

50

50

60
70

00

5

10

15

20

0

0

5

+10

5

10

15

30

20

30

40

40

50

50

60
70

20

30

40

40

50

50

60
70

20

30

40

40

50

50

60
70

20

30

40

40

50

50

60
70

20

30

40

40

50

50

60
70

15

0

5

10

15

20

0

5

+10

5

10

0

30

15

5

10

15

20

0

5

+10

5

10

0

30

15

5

10

15

20

0

5

+10

5

10

0

30

15

5

10

15

20

0

5

+10

5

10

0

30

15

20

30

40

40

50

50

60
70

30

15

20

30

40

40

20

30

40

20

30

40

20

30

40

50

50505050

20

30

40

50

20

30

40

50

60
70

40

50

60
70

40

50

60
70

40

50

60
70

40

50

60
70

40

50

60
70

40

50

60
70

40

50

60
70

30

15

5

10

15

20

0

5

+10

5

10

0

5

10

15

20

0

5

+10

5

10

0

5

10

15

20

0

30

5

10

15

20

0

30

5

10

15

20

0

30

5

10

15

20

0

30

5

10

15

20

0

303030

5

10

15

20

0

5

10

15

20

0

5

10

15

20

0

5

+10

5

10

0

15

5

+10

5

10

0

15

5

+10

5

10

0

15

5

+10

5

10

0

15

20

30

40

50

15 15

20

30

40

50

15

5

+10

5

10

0

5

+10

5

10

0

5

+10

5

10

0

5

+10

5

10

0

123456

123456

7

891011 12

7

891011 12

13 14 15 16

13 14 15 16

32313029282726252423222120191817

STEREO

13 14 15 16

OVER

0

-3

-6

-9

-12

-15

-18

-24

-30

-36

-48

AD Input Section (p. 14)

SELECTED
CHANNEL
Section (p. 20)

Monitor Out
& Head­phones Sec­tion (p. 15)

SOLO Section
(p. 22)

Channel Strip Section (p. 16) STEREO Section (p. 16) USER DEFINED KEYS

Section (p. 21)

Data Entry
Section (p. 22)

LAYER Section
(p. 19)

SCENE MEMORY Section (p. 21)

Display Section
(p. 19)

DISPLAY ACCESS
Section (p. 18)

ST IN Section
(p. 17)

FADER MODE
Section (p. 17)

2 Control Surface & Rear Panel

Control Surface

2

Control Surface & Rear Panel

01V96—Owner’s Manual

14 Chapter 2—Control Surface & Rear Panel

AD Input Section

CH1-4

121110943215

1513

1

3

4

5
6
7

OUTIN

(UNBAL)

A

A

B

INPUT

(BAL)

INSERT

PAD

B

/

O INSERT I/O INSERT I/O INSERT I/O INSERT I/O INSERT I/O INSERT I/O INSERT I/O INSERT I/O

INSERT I

-60

-16
GAIN

PEAK
SIGNAL

A

B

-60

-16
GAIN

PEAK
SIGNAL

A

A

B

B

-16
GAIN

PEAK
SIGNAL

GAIN

PEAK
SIGNAL

-60

-60

-16

-60

-16
GAIN

PEAK
SIGNAL

A

A

B

B

20dB20dB20dB20dB20dB20dB20dB

-60

-16

-16

PEAK
SIGNAL

GAIN

PEAK
SIGNAL

GAIN

A INPUT connectors A/B

INPUT A connectors are balanced XLR-3-31-type connectors that accept line-level and
microphone signals. Each of the phantom [+48V] switches on the rear panel turns on or off
the +48V phantom power feed to the corresponding input. INPUT B connectors are bal­anced TRS phone-type connectors that accept line-level and microphone signals. The nom­inal signal level of both types of connectors ranges from –60 dB to +4 dB. Phantom power
is not supplied to these connectors.

If you connect cables to INPUT A and INPUT B connectors of the same number, only the
signal from INPUT B is effective.

Male XLR plug

1 (ground)

3 (cold)

A

B

-60

A

B

20dB

20dB

-60

-16

-16
GAIN

GAIN

PEAK
SIGNAL

PEAK
SIGNAL

1/4" TRS phone plug

14

-26

+4

GAIN

-60

-26

+4

GAIN

PEAK

13 14 15 16

SIGNAL

16

CH15/16
2TR IN

-26

+4

GAIN

-26

+4

GAIN

PEAK

SIGNAL

Ring (cold)

2

8

Tip (hot)

2 (hot)

Sleeve (ground)

B INPUT connectors 13–16

These balanced TRS phone-type connectors accept line-level signals. The nominal signal
level ranges from –26 dB to +4 dB. INPUT 15 & 16 connectors are available only when the
AD 15/16 button is turned off (page 15).

C INSERT I/O connectors

These unbalanced TRS phone-type connectors are used for channel insert ins and outs. Use
a split cable to insert an external effects processor to AD input channels.

Tip (send)

Sleeve
(ground)

Tip (return)

Tip (send)

Ring (return)

1/4" phone plug

Sleeve (ground)

Connect to INSERT jack

1/4" phone plug

To processor’s input

1/4" phone plug

Sleeve (ground)

From processor’s output

01V96—Owner’s Manual

Control Surface 15

D PAD switches

These switches turn on or off the 20 dB pad (attenuator) for each AD Input.

E GAIN controls

These controls adjust input sensitivity for each AD Input. Input sensitivity is –16 dB to
–60 dB when the Pad is off, and +4 dB to –40 dB when the Pad is on.

F PEAK indicators

These indicators light up when the input signal level is 3 dB below clipping. Adjust the Pad
switch and GAIN control so that the indicator rarely lights up at signal peak.

G SIGNAL indicators

These indicators light up when the input signal level exceeds –34 dB.

H AD15/16 selector

This button selects AD Input Channel 15 and 16 signals. When the button is turned on
(pushed in), the 2TR IN signals (page 24) are selected. When the button is turned off
(raised), the INPUT 15 and 16 signals are selected.

Monitor Out & Headphones Section

CH9-12CH5-8

PHANTOM +48V

L

1

2

3

IN OUT

2TR

-10dBV (UNBAL)

MONITOR
2TR IN

0

LEVEL

MONITOR

OUT

R

5

PHONES

0

10

10

LEVEL

PHONES

4

2

Control Surface & Rear Panel

A 2TR IN/OUT connectors

These unbalanced RCA phono connectors input and output line-level signals, and are typ­ically used to connect a master recorder.

When the AD15/16 selector in the AD Input section (8) is turned on (pushed in), the sig­nals input at the 2TR IN connectors are routed to AD Input Channels 15 and 16. When the
Monitor Source selector (2) is turned on (pushed in), you can monitor the 2TR IN signals
from the MONITOR OUT connectors.

The 2TR OUT signals are always the same as the STEREO OUT signals.

B Monitor Source selector

This button selects the signals output from the MONITOR OUT connectors on the rear
panel. When this button is turned on (pushed in), you can monitor the signals input from
the 2TR IN connectors. When the button is turned off (raised), you can monitor the Stereo
Out signals or soloed channel signals.

C MONITOR LEVEL control

This control adjusts the monitoring level of the signals output from the MONITOR OUT
connectors.

D PHONES LEVEL control

This control sets the level of the PHONES. (See page 131 for more information on moni­toring through the headphones.)

E PHONES jack

You can connect a set of stereo headphones to this stereo phone jack. The signals output
from the MONITOR OUT connectors are also output from this jack.

01V96—Owner’s Manual

16 Chapter 2—Control Surface & Rear Panel

Channel Strip Section

A [SEL] buttons

These buttons enable you to select desired channels. The [SEL] button indicator for the cur-

1

2

3

4

SEL

SOLO

ON

1

+10

0

5

5

0

10

5

15

20

10

15

30

20

40

50

30

60

40

70

50

1

17

AUX 1

rently-selected channel lights up. The channel selected by each [SEL] button depends on the
layer selected in the LAYER section (see page 19).

These buttons also allow you to create or cancel channel pairs, and add channels to (or
remove them from) Fader, Mute, EQ, and Compressor groups.

B [SOLO] buttons

These buttons solo the selected channels. The [SOLO] button indicator of the cur­rently-soloed channel lights up.

C [ON] buttons

These buttons turn the selected channels on or off. The [ON] button indicators for On
channels light up.

D Channel faders

Depending on the button selected in the FADER MODE section (see page 17), these faders
adjust the selected channel input levels or the Bus Out or Aux Out levels.

1

2

3

STEREO Section

A [SEL] button

SEL

ON

0

5

10

15

20

30

40

50

60
70

STEREO

Selects the Stereo Out.

B [ON] button

Tu r ns the Stereo Out on or off.

C [STEREO] fader

This 100mm motorized fader adjusts the final output level of the Stereo Out.

01V96—Owner’s Manual

ST IN Section

Control Surface 17

1

2

3

4

ST IN

SEL SEL

SOLOONSOLO

ON

ST IN 1 ST IN 2

5

A [ST IN] button

This button selects an ST IN channel pair (ST IN Channels 1 & 2 or 3 & 4) which you can
control using the buttons and controls in the ST IN section. The indicators to the right of
the button indicate the available ST IN channels.

B [SEL] buttons

These buttons select the ST IN channel you want to control.

C [SOLO] buttons

These buttons solo the selected ST IN channels.

D [ON] buttons

These buttons turn the ST IN channels on or off.

2

Control Surface & Rear Panel

E Level controls

These controls adjust the ST IN channel levels.

FADER MODE Section

FADER MODE

1

2

A [AUX 1]–[AUX 8] buttons

These buttons enable you to select the Aux Send you wish to control. Pressing one of these
buttons switches the Fader mode (see page 33), and displays the corresponding Aux page.
(The selected button’s indicator lights up.)

You can now adjust the send level of signals routed from Input Channels to the correspond­ing Aux buses by using the faders.

B [HOME] button

This button recalls Meter pages that display Input Channel levels or Output Channel (Bus
Out, Aux Out, Stereo Out) levels (see page 34).

AUX 1 AUX 2 AUX 3 AUX 4

AUX 8AUX 7AUX 6AUX 5

HOME (METER)

01V96—Owner’s Manual

18 Chapter 2—Control Surface & Rear Panel

DISPLAY ACCESS Section

6
5

1 2 3

DISPLAY ACCESS

DIO/SETUP

DIO/SETUP

PAN/

/ INSERT/

ROUTING

DELAY

EQ EFFECT VIEW

DYNAMICS

PAIR/

GROUP

4

UTILITYMIDISCENE

UTILITYMIDISCENE

PATCH

7
8

9 J K L

A [SCENE] button

This button displays a Scene page, enabling you to store and recall Scenes (see page 161).

B [DIO/SETUP] button

This button displays a DIO/Setup page, enabling you to set up the 01V96, including digital
input and output setup and remote control setup (see pgaes 72, 188).

C [MIDI] button

This button displays a MIDI page, enabling you to make MIDI settings (see page 215).

D [UTILITY] button

This button displays a Utility page, enabling you to use the internal oscillators and view
information about installed optional cards.

E [ /INSERT/DELAY] button

This button displays a /INS/DLY page, enabling you to switch the signal phase, set the
signal to be inserted, or set the delay parameters (see pages 79, 127).

F [PAN/ROUTING] button

This button displays a Pan/Route page, enabling you to select a Bus to which the selected
channel signal is routed, adjust the selected channel pan settings, adjust the level of signals
routed from Buses 1–8 to the Stereo Bus, and adjust the stereo or surround pan settings (see
pages 85, 135).

G [PAIR/GROUP] button

This button displays a Pair/Grup page, enabling you to create or cancel channel pairs and
group multiple channel faders or [ON] buttons (see pages 93, 147).

H [PATCH] button

This button displays a Patch page, enabling you to patch input signals and Bus Out signals
to Input channels, or patch signals to the desired output connectors (see page 121).

I [DYNAMICS] button

This button displays a Dynamics page, enabling you to control channel gates and compres­sors (see page 81).

J [EQ] button

This button displays an EQ page, enabling you to set the equalizer and attenuator of the
selected channel (see page 84).

K [EFFECT] button

This button displays an Effect page, enabling you to edit the internal effects processors and
use optional plug-in cards (see page 157).

L [VIEW] button

This button displays a View page, enabling you to view and set mix parameters for a specific
channel (see page 87).

01V96—Owner’s Manual

Control Surface 19

LAYER Section

LAYER

1-16 17-32 MASTER REMOTE

1 2 3

A [1–16]/[17–32] buttons

These buttons select an Input Channel layer as the layer controlled in the Channel Strip sec­tion. When the [1–16] button is turned on, you can control Channels 1–16. When the
[17–32] button is turned on, you can control Channels 17–32. (See page 31 for more infor­mation on the Input Channel layers.)

B [MASTER] button

This button selects the Master Layer as the layer controlled in the Channel Strip section. You
can use this layer to control Bus Outs and AUX Sends. (See page 31 for more information
on the Master layer.)

C [REMOTE] button

This button selects the Remote Layer as the layer controlled in the Channel Strip section.
You can use this layer to control external MIDI devices or computer-based DAWs. (See
page 185 for more information on the Remote layer.)

2

Control Surface & Rear Panel

Tip: The ST IN section is not affected by the layer settings.

Display Section

1

STEREO

5

A Display

This is a 320 x 240 dot LCD display with a backlight.

B Stereo meters

These 12-segment level meters display the final output level of the Stereo Bus.

4

6

OVER

0

-3

-6

-9

-12

-15

-18

-24

-30

-36

-48

2

3

C Contrast control

This control adjusts the display contrast.

D [F1]–[F4] buttons

These buttons select a page from a multi-page screen. Selecting a tab at the bottom of the
screen using one of these buttons displays the corresponding page. (See page 28 for more
information on displaying a page.)

01V96—Owner’s Manual

20 Chapter 2—Control Surface & Rear Panel

E Left Tab Scroll [ ] button
F Right Tab Scroll [ ] button

If there are more pages available than the four whose tabs are currently displayed, use these
buttons to display the additional tabs. These buttons are available only when the left or right
Tab Scroll arrow appears.

SELECTED CHANNEL Section

6

7

8

Tab Scroll arrow

SELECTED CHANNEL

PAN

EQUALIZER

HIGH

Q

HIGH-MID

FREQUENCY

LOW-MID

LOW

GAIN

1

2

3

4

5

A [PAN] control

This control adjusts the pan of the channel selected by the [SEL] button.

B [HIGH] button
C [HIGH-MID] button
D [LOW-MID] button
E [LOW] button

These buttons select the EQ band (HIGH, HIGH-MID, LOW-MID, LOW) of the channel
selected by the [SEL] button. The corresponding button indicator of the currently-selected
band lights up.

F [Q] control

This control adjusts the currently-selected band Q.

G [FREQUENCY] control

This control adjusts the currently-selected band frequency.

H [GAIN] control

This control adjusts the currently-selected band gain.

01V96—Owner’s Manual

SCENE MEMORY Section

Control Surface 21

SCENE MEMORY

STORE

1 3

2

RECALL

A [STORE] button

This button enables you to store the current mix settings. (See page 161 for more informa­tion on Scene Memories.)

B Scene Up [ ] / Down [ ] buttons

These buttons select a Scene to store or recall. Pressing the Scene Up [ ] button increments
the selection; pressing the Scene Down [ ] button decrements the selection. Holding down
either key increments or decrements the selection continuously.

C [RECALL] button

This button recalls the Scene memory selected by the Scene Up [ ] / Down [ ] buttons.

USER DEFINED KEYS Section

USER DEFINED

KEYS

12

34

1

56

2

Control Surface & Rear Panel

78

A [1]–[8] buttons

You can assign any of the 167 functions to these User Defined buttons.

01V96—Owner’s Manual

22 Chapter 2—Control Surface & Rear Panel

Data Entry Section

DEC INC

4

3

1

2

ENTER

A Parameter wheel

This control adjusts the parameter values shown on the display. Turning it clockwise
increases the value; turning it counterclockwise decreases the value. This wheel also enables
you to scroll a displayed list and select a character for entry (see page 30).

B [ENTER] button

This button activates a selected (highlighted) button on the display, and confirms the edited
parameter values.

C [DEC] & [INC] buttons

These buttons increment or decrement a parameter value by one. Pressing the [INC] but­ton increments the value; pressing the [DEC] button decrements the value. Holding down
either key increments or decrements the value continuously.

D Left, Right, Up, Down ([ ]/[ ]/[ ]/[ ]) cursor buttons

These buttons move the cursor around the display pages, or select parameters and options.
Holding down a cursor button moves the cursor continuously in the corresponding direc­tion.

SOLO Section

1

SOLO CLEAR

2

A [SOLO] indicator

This indicator flashes when single or multiple channels are soloed.

B [CLEAR] button

This button “unsolos” all soloed Channels.

01V96—Owner’s Manual

Rear Panel

Rear Panel 23

PHANTOM +48V (p. 23)

Power Section (p. 25)

PHANTOM +48V

AD Output Section
(p. 23)

Digital I/O Section
(p. 24)

SLOT Section (p. 25)

MIDI/Control Section
(p. 25)

2

Control Surface & Rear Panel

3 2 1

A CH1–4 ON/OFF switch
B CH5–8 ON/OFF

switch

C CH9–12 ON/OFF switch

Each of these switches turns on or off the +48V phantom power feed to four corresponding
inputs. When the switches are on, +48V phantom power is supplied to the INPUT A con­nectors.

AD Output Section

321

A MONITOR OUT connectors L/R

These balanced TRS phone-type con­nectors output monitoring signals or
2TR IN signals. The nominal signal
level is +4 dB.

You can select signals using the Mon­itor Source selector.

1/4" TRS phone plug

Ring
(cold)

Sleeve (ground)

Tip (hot)

01V96—Owner’s Manual

24 Chapter 2—Control Surface & Rear Panel

B OMNI OUT connectors 1–4

These balanced TRS phone-type con­nectors output any Bus signals or
channel Direct Out signals. The nom­inal signal level is +4 dB.

C STEREO OUT connectors L/R

These balanced XLR-3-32-type con­nectors output the Stereo Out signals.
The nominal signal level is +4 dB.

Digital I/O Section

1/4" TRS phone plug

Female XLR plug

421 53

Tip (hot)

Ring
(cold)

Sleeve (ground)

2 (hot)

3 (cold)

1 (ground)

A WORD CLOCK OUT connector

This BNC connector outputs a wordclock signal from the 01V96 to a connected external
device.

B WORD CLOCK IN connector

This BNC connector inputs a wordclock signal from a connected external device to the
01V96.

C ADAT IN/OUT connectors

These optical TOSLINK connectors input and output ADAT digital audio signals.

D 2TR OUT DIGITAL COAXIAL

This RCA phono connector outputs consumer format (IEC-60958) digital audio. The con­nector is typically used to connect the digital stereo input (consumer format) of a DAT
recorder, MD recorder, or CD recorder.

E 2TR IN DIGITAL COAXIAL

This RCA phono connector accepts consumer format (IEC-60958) digital audio. The con­nector is typically used to connect the digital stereo output (consumer format) of a DAT
recorder, MD recorder, or CD recorder.

01V96—Owner’s Manual

Rear Panel 25

MIDI/Control Section

21

A MIDI IN/THRU/OUT ports

These standard MIDI IN, OUT and THRU ports enable you to connect the 01V96 to other
MIDI equipment.

B TO HOST USB port

This USB port enables you to connect a computer equipped with a USB port.

SLOT Section

2

Control Surface & Rear Panel

1

A SLOT

You can insert optional mini-YGDAI cards into this slot. (See page 26 for information on
installing these cards.)

Power Section

21

A POWER ON/OFF switch

This switch turns the power to the 01V96 on or off.

Note: To prevent loud clicks and thumps in your speakers, turn on your audio equipment in
the following order (reverse this order when turning the equipment off )—sound sources, mul­titrack and master recorders, 01V96, monitoring power amplifiers.

B AC IN connector

This connector enables you to connect the 01V96 to an AC outlet via the supplied power
cord.

01V96—Owner’s Manual

26 Chapter 2—Control Surface & Rear Panel

Installing an Optional Card

Visit the following Yamaha Pro Audio web site to ensure that the card you are installing is
supported by the 01V96.

<http://www.yamahaproaudio.com/>.

Follow the steps below to install an optional mini-YGDAI card.

1 Make sure that the power to the 01V96 is turned off.

2 Undo the two fixing screws and remove the slot cover, as shown below.

Keep the cover and fixing screws in a safe place for future use.

3 Insert the card between the guide rails and slide it all the way into the slot,

as shown below.

You may have to push firmly to fully insert the card into the internal connector.

4 Secure the card using the attached thumbscrews.

Tighten the screws firmly to secure the card. Otherwise, the card may not be grounded cor­rectly.

01V96—Owner’s Manual

3 Operating Basics

This chapter describes basic operations on the 01V96, including how to use the display and
operate the controls on the top panel.

Operating Basics 27

About the Display

The top panel display indicates various parameters that you must set before you can operate
the 01V96. The display indicates the following items:

1Selected

DISPLAY

2Selected

channel

9Page title

KPage area

3Current Scene

3

Operating Basics

4EDIT indicator

5MIDI indicator

6Surround mode indicator

7Sampling rate indicator

8ST IN channel

levels

JChannel name

MTab Scroll arrowsLPage tabs

A Selected DISPLAY

This section indicates the currently-selected display page group.

B Selected channel

This section indicates the Input or Output Channel currently selected by its correspond­ing [SEL] button. The first four characters are the Channel ID (e.g., CH1–CH32,
BUS1–BUS8, AUX1–AUX8, ST-L, ST-R). The second four characters are the channel’s
Short name. You can edit the channel’s Short name if you desire (see page 225).

C Current Scene

This section indicates the number and title of the currently-selected Scene memory (see
page 162). If the selected Scene is write-protected, a padlock icon ( ) appears.

D EDIT indicator

This indicator appears when the current mix settings no longer match those of the Scene
that was most-currently recalled.

E MIDI indicator

This indicator appears when the 01V96 is receiving MIDI data via the MIDI IN port,
USB port, or an installed MY8-mLAN card.

F Surround mode indicator

This indicator identifies the currently-selected Surround mode (ST=stereo, 3-1, 5.1, or

6.1) (see page 135).

01V96—Owner’s Manual

28 Chapter 3—Operating Basics

G Sampling rate indicator

This indicator identifies the 01V96’s current sampling rate: 44.1 kHz (44k), 48 kHz
(48k), 88.2 kHz (88k), or 96 kHz (96k).

H ST IN channel levels

These level controls indicate the level of ST IN channels 1–4.

I Page title

This section indicates the title of the current page.

J Channel name

On certain pages, this area displays the Long name of the currently-selected channel.

K Page area

This page area displays various page contents.

L Page tabs

These tabs enable you to select a display page.

M Tab Scroll arrows

These arrows indicate that more pages are available.

Selecting Display Pages

To select a display page:

1 Press the corresponding button on the top panel to select the desired page

group.

Display pages are grouped by function. To select a page group, press the desired button in
the DISPLAY ACCESS section.

2You can select pages that have currently-displayed tabs by pressing the

[F1]–[F4] buttons.

If the selected display page group contains multiple pages, press the [F1]–[F4] buttons
below the corresponding tab to select a specific page.

3To select a page for which a tab is not currently displayed, press either the

Left or Right [ ]/[ ] Tab Scroll button (depending on where the page is
located) to display the page tab, then press the corresponding [F1]–[F4] but­ton.

If display page groups contain more than four pages, either the left or right arrow appears.
To display the currently-hidden tabs, press the Right or Left [ ]/[ ] Tab Scroll button.

You can also select a page from a page group as follows:

• Selecting the next page in a page group:

Press the button you selected in Step 1 repeatedly. This enables you to select a page that has
a hidden tab.

•To select the previous page in a page group:

Press and hold down the button you selected in Step 1. The screen steps back through the
pages one by one. Release the button when the desired page is displayed. This enables you
to select a page that has a hidden tab.

•To select the first page in the group:

Double-click the button you selected in Step 1.

01V96—Owner’s Manual

4 Press the cursor buttons to move the cursor (a bold frame) to a button,

parameter box, rotary control, or fader so that you can change the value.

Tip: The 01V96 remembers the current page and parameter when you select a new page group.
If you return to the previous page group, the 01V96 displays the correct page, with the same
parameter selected. You can also select a page by using the controls or buttons on the top panel
(see page 226).

Display Interface

This section describes how to use the display interface.

Rotary Controls & Faders

The rotary controls and faders enable you to adjust the contin­uously variable parameter values, including Input Channel lev­els and effects parameters. Press the cursor buttons to move the
cursor to a rotary control or fader you want to adjust, then
rotate the Parameter wheel or press the [INC]/[DEC] buttons
to modify the value.

Display Interface 29

3

Operating Basics

Buttons

The buttons enable you to turn certain functions on
(enabled) or off (disabled). Move the cursor to the appropri­ate button, then press the [ENTER] button to turn the func­tion on (highlighted) or off. The buttons also enable you to
select one of two options or to execute certain functions.

Parameter Boxes

The parameter boxes enable you to select one of multiple
options. Press the cursor buttons to move the cursor to a
parameter box, then rotate the Parameter wheel or press the
[INC]/[DEC] buttons to select the setting.

You may need to press the [ENTER] button to confirm a
change in certain parameter boxes. If you edit a value in this
type of parameter box, the value flashes. Press the [ENTER]
button to confirm the change, and the flashing stops. If you
move the cursor to other parameters while the edited value is
flashing, the edit is cancelled.

01V96—Owner’s Manual

30 Chapter 3—Operating Basics

Confirmation Messages

For certain functions, the 01V96 prompts you for confirmation before executing the func­tions, as shown here.

Move the cursor to YES and press [ENTER] to execute the function, or move the cursor to
NO and press [ENTER] to cancel.

If you take no action for awhile, the confirmation window closes automatically and the
function is not executed.

Title Edit Window

The Title Edit window enables you to enter titles for Scene and library memories. You can
enter 4, 12, or 16 characters, depending on the item.

The figure on the left shows uppercase characters and various punctuation marks. The fig­ure on the right shows lowercase characters and numbers.

Use the cursor buttons to select characters, and press the [ENTER] button to enter them
into the title. The cursor moves to the right automatically as each character is entered. Use
the Parameter wheel to move the cursor within the title.

Use the SHIFT LOCK button to select uppercase or lowercase characters, and use the SPC
button to enter a space.

To insert a space at the cursor position and move subsequent characters to the right, move
the cursor to the INS button and press [ENTER].

To delete the character at the cursor position and move subsequent characters to the left,
move the cursor to the DEL button and press [ENTER].

When you have finished, move the cursor to the OK button, then press [ENTER] to confirm
the title. To cancel the title entry, move the cursor to the CANCEL button, then press
[ENTER].

01V96—Owner’s Manual