English
UC
YIT-W10
Wireless transmitter for iPod
Transmetteur sans fil pour iPod
OWNER’S MANUAL
MODE D’EMPLOI
Français
FCC INFORMATION (for US customers)
1.
IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions
contained in this manual, meets FCC requirements.
Modifications not expressly approved by Yamaha may
void your authority, granted by the FCC, to use the product.
2. IMPORTANT
3. NOTE:
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received including interference that may cause undesired operation.
See user manual instructions if interference to radio reception is suspected.
This equipment compiles with FCC/IC radiation exposure limits set forth for uncontrolled equipment and meets the
FCC radio frequency (RF)
Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. This
equipment has very low levels of RF energy that it deemed to comply without maximum permissive exposure
evaluation (MPE). But it is desirable that it should be installed and operated with at least 20 cm and more between the
radiator and person’s body (excluding extremities: hands, wrists, feet and ankles).
NOTICE
This equipment has been tested and found to comply with the li mits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
FCC WARNING
Change or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to wide slot and fully insert.
This Class B digital apparatus complies with Canadian ICES-003.
:
When connecting this product to accessories and/or
another product use only high quality shielded cables.
Cable/s supplied with this product MUST be used. Follow
all installation instructions. Failure to follow instructions
could void your FCC authorization to use this product in
the USA.
This product has been tested and found to comply with the
requirements listed in FCC Regulations, Part 15 for Class
“B” digital devices. Compliance with these requirements
provides a reasonable level of assurance that your use of
this product in a residential environment will not result in
harmful interference with other electronic devices.
This equipment generates/uses radio frequencies and, if not
installed and used according to the instructions found in the
users manual, may cause interference harmful to the
operation of other electronic devices.
Compliance with FCC regulations does not guarantee
that interference will not occur in all installations. If this
product is found to be the source of interference, which
can be determined by turning the unit “OFF” and “ON”,
please try to eliminate the problem by using one of the
following measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV in terference, relocate/reorient
the antenna. If the antenna lead-in is 300 ohm ribbon
lead, change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local ret ailer a uthorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electron ics Corp.,
U.S.A. 6660 Orangethorpe Ave, Buena Park, CA 90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
1 En
Caution: Read this before operating this unit.
1 To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
2 Locate this unit away from other electrical
appliances, motors, or transformers to avoid
humming sounds.
3 Do not expose this unit to sudden temperature
changes from cold to hot, and do not locate this
unit in an environment with high humidity (i.e. a
room with a humidifier) to prevent condensation
inside this unit, which may cause an electrical
shock, fire, damage to this unit, and/or personal
injury.
4 Avoid installing this unit where foreign object
may fall onto this unit and/or this unit may be
exposed to liquid dripping or splashing. On the
top of this unit, do not place:
–Other components, as they may cause damage and/or
discoloration on the surface of this unit.
–Burning objects (i.e. candles), as they may cause fire,
damage to this unit, and/or personal injury.
–Containers with liq uid in them, as they may fall and
liquid may cause electrical shock to the user and/or
damage to this unit.
5 Do not cover this unit with a newspaper,
tablecloth, curtain, etc. in order not to obstruct
heat radiation. If the temperature inside this unit
rises, it may cause fire, damage to this unit, and/
or personal injury.
6 Do not plug in this unit to a wall outlet until all
connections are complete.
7 Do not use force on switches, knobs and/or cords.
8 When disconnecting the power cable/AC adapter
from the wall outlet, grasp the plug; do not pull
the cable.
9 Do not clean this unit with chemical solvents; this
might damage the finish. Use a clean, dry cloth.
10 Only voltage specified on this unit must be used.
Using this unit with a higher voltage than
specified is dangerous and may cause fire,
damage to this unit, and/or personal injury.
Yamaha will not be held responsible for any
damage resulting from use of this unit with a
voltage other than specified.
11 Do not attempt to modify or fix this unit. Contact
qualified Yamaha service personnel when any
service is needed. The cabinet should never be
opened for any reasons.
2 En
12 When not planning to use this unit for long
periods of time (i.e. vacation), disconnect the AC
power plug from the wall outlet.
13 Be sure to read the “Troubleshooting” section on
common operating errors before concluding that
this unit is faulty.
14 Before moving this unit, turn off this unit, and
disconnect the AC power plug from the wall
outlet.
15 Condensation will form when the surrounding
temperature changes suddenly. Disconnect the
power cable from the outlet, then leave this unit
alone.
16 When using this unit for a long time, this unit may
become warm. Turn the power off, then leave this
unit alone for cooling.
17 Install this unit near the AC outlet and where the
AC power plug can be reached easily.
18 Be sure to use the AC adaptors supplied with this
unit. Using an AC adaptor other than those
provided may cause fire or damage to this unit.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN
OR MOISTURE.
CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein may result
in hazardous radiation exposure.
Radio waves may affect electro-medical devices.
Do not use this unit near medical devices or inside
medical facilities.
Do not use this unit within 22 cm (9 inches) of persons
with a heart pacemaker implant or defibrillator implant.
Even if an iPod or iPhone is not connected to this unit,
this unit is not discon nected from the AC power source
as long as it is connected to the AC wall outlet. In this
state, this unit is designed to consume a very small
quantity of power.
Be sure to use this product only in the country in where
it was purchased.
This transmitter must not be co-located or operated in
conjunction with any other antenna or transmitter.
IMPORTANT
Please record the serial number of this unit in the space below.
MODEL:
Serial No.:
The serial number is located on the rear of the unit. Retain
this Owner’s Manual in a safe place for future reference.
■ Introduction
YIT-W10 is a wireless transmitter designed for iPod
or iPhone series. YIT-W10 employs the Yamaha
“yAired” technology to establish a wireless
connection with another Yamaha product that
supports “yAired” and enables playback of the iPod
or iPhone on your Yamaha product.
Also the charging cradle can be used for charging the
iPod or iPhone, or to play music or movies for an
extended time.
■ Included items
YIT-W10 consists of a transmitter PDX-50TX, a
charging cradle PDX-50BC, and an AC adapter.
Check that you have received all of the following
included items.
Wireless transmitter for iPod x1 (PDX-50TX)
Charging cradle x1 (PDX-50BC)
AC adapter x1 (MU12-2050100-A1)
■ Using YIT-W10
1 Connect the AC adapter to PDX-50BC
(charging cradle) and then connect the
AC plug to the AC wall outlet.
PDX-50BC AC adapter
2 Remove the transparent film on the pad.
3 Connect your iPod or iPhone to PDX-
50TX (transmitter).
The green LED lights up if a wireless connection
between PDX-50TX and another Yamaha
product is established.
OWNER’S MANUAL
YIT-W10
Wireless transmitter for iPod
Transmetteur sans fil pour iPod
OWNER’S MANUAL
MODE D’EMPLOI
UC
English
Français
PDX-50TX
Status LEDs
3 En
LED Status
Off An iPod or iPhone is not
Flashes green
continuously
Flashes green
once
Lights up
green
Lights up
green and
flashes red
Flashes red
(regardless of
green status)
4 Adjust the angle of your iPod or iPhone
so that it is aligned parallel to PDX-50TX.
5 To charge the iPod or iPhone, place it on
PDX-50BC.
connected, or has stopped
playing. However, lights up
for 30 seconds or 2 minutes
(depends on the iPod/iPhone)
after connecting or stopping
playback.
Connection in progress,
please wait.
Adjusting the volume level.
A connection is established.
You are ready to start
playback of iPod on another
Yamaha product.
Flashes red for 2 seconds: An
unsupported iPhone or iPod is
connected.
Keeps flashing red:
Connection failed.
The battery of the iPod or
iPhone is low.
■ Group selection switch
Use this switch to set the group ID. To establish a
wireless connection (yAired) with another Yamaha
product, set both the products to the same group.
Group selection switch
Match the group
selection switch with
the group ID to set.
y
• PDX-50TX supports “1” (A1), “2” (A2), and “3”
(A3) on some Yamaha products that support
“yAired”.
■ Disconnecting the iPod or iPhone
To disconnect the iPod or iPhone from PDX-50TX
(transmitter), pull the iPod or iPhone upward.
y
• Disconnection may be difficult under low
temperature. In this case, do not disconnect the
iPod or iPhone by force; loosen off the tab on the
back of PDX-50TX to make the disconnection
easier.
4 En
■ Troubleshooting
Refer to the table below if the unit does not function properly. If the problem you are experiencing is not listed
below, or if the instruction below does not help, contact the nearest authorized Yamaha dealer or service center.
Problem Cause Remedy
No sound. PDX-50TX and another Yamaha
Controlling
volume on the iPod
or iPhone does not
work.
product are not connected since they
are set to different groups.
The signals are obstructed because
there is an obstacle between the
transmitting-side product and this
unit.
There is a device (microwave oven,
wireless LAN, etc.) outputting signals
in 2.4 GHz frequency band nearby.
The iPod or iPhone is not connected
to PDX-50TX firmly.
The firmware of the iPod or iPhone is
not updated.
The signal from PDX-50TX is
blocked by your body or metallic
objects, etc.
The battery of iPod or iPhone is low. Charge the iPod or iPhone.
The volume is turned down. Turn up the volume.
It is in the process of a connection. Please wait for a while.
The protection circuitry has been
activated by excessive volume.
The iPod or iPhone being used is not
supported by this unit.
The iPod or iPhone is not connected
to PDX-50TX firmly.
Set both PDX-50TX and another
Yamaha product to the same group.
Remove the obstacle.
Move this unit to another position.
If the device is IEEE802.11ncompliant, change the channel
setting of the device so as not to
affect the unit.
Move PDX-50TX away from the
device.
Connect the iPod or iPhone firmly.
Download the latest iTunes software
to update the firmware of the iPod or
iPhone. For details, refer to the
owner’s manual supplied with your
iPod or iPhone.
Change the way of holding,
orientation, or position of PDX50TX to avoid the object blocking
the signal.
Turn down the volume.
Use an iPod or iPhone supported by
this product.
Connect the iPod or iPhone firmly.
5 En
■ Specifications
Supported iPod
....iPod (5th ge neration), iPod classic, iPod nano,
Supported iPhone
...............................................iPhone, iPhone 3G,
Power supply ................................AC 120 V, 60 Hz
Power consumption ...........................................4 W
Power consumption without connecting
iPod/iPhone..................................... less than 1 W
Transmission range
.........Approx. 20 m (66 ft) (without interference)
Maximum playback duration
..........Approx. 10 hours (from full charged iPod)
Dimensions (W x D x H)
PDX-50TX...........................45.4 x 21.6 x 81 mm
PDX-50BC............................. 56 × 20.5 × 74 mm
Weight
PDX-50TX......................................29 g (1.02 oz)
PDX-50BC...................................29.5 g (1.04 oz)
This unit does not support iPod (4th generation or
before), iPod without Dock connector, iPod photo
and iPod mini.
* Specifications are subject to change without notice
iPhone 3GS (as of August 2009)
(1-29/32 × 7/8 × 3-7/32 in)
(2-7/32 × 13/16 × 2-15/16 in)
iPod touch
The “ ” and “yAired” are
trademarks of Yamaha Corporation.
iPod™, iPhone
iPod is a trademark of Apple Inc., registered
in the U.S. and other countries.
iPhone is a trademark of Apple Inc.
“Made for iPod” means that an electronic
accessory has been designed to connect
specifically to iPod and has been certified by
the developer to meet Apple performance
standards.
“Works with iPhone” means that an
electronic accessory has been designed to
connect specifically to iPhone and has been
certified by the developer to meet Apple
performance standards.
Apple is not responsible for the operation of
this device or its compliance with safety and
regulatory standards.
™
6 En
Serial No. / No. de série
© 2009 Yamaha Corporation All rights reserved. Printed in Malaysia WT82070
Loading...