Yamaha RX-10 Owner Manual

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

Natural Sound Stereo Receiver

Ampli-syntoniseur stéréo de la série “Natural Sound”

Natural Sound Stereoreceiver

Ricevitore stereo a suono naturale

Receptor estéreo de Sonido Natural

Natural Sound Stereo Ontvanger

RX-10

SUPPLIED ACCESSORIES

●

After unpacking, check that the following parts are contained.

ACCESSOIRES FOURNIS

●

Après le déballage, vérifier que les pièces suivantes sont incluses.

MITGELIEFERTES ZUBEHOR

●

Nach dem Auspacken überprüfen, ob die folgenden Teile vorhanden sind.

MEDFOLJANDE TILLBEHOR

●

Kontrollera efter det apparaten packats upp att följande delar finns med.

ACCESSORI IN DOTAZIONE

●

Verificare che tutte le parti seguenti siano contenute nell’imballaggio dell’apparecchio.

ACCESORIOS INCLUIDOS

●

Desembale el aparato y verificar que los siguientes accesorios están en la caja.

BIJGELEVERDE ACCESSOIRES

●

Controleer na het uitpakken of de volgende onderdelen voorhanden zijn.

This product complies with the radio frequency interference requirements of the Council Directive 82/499/EEC and/or 87/308/EEC.

Cet appareil est conforme aux prescriptions de la directive communautaire 87/308/CEE. Diese Geräte entsprechen der EG-Richtlinie 82/499/EWG und/oder 87/308/EWG. Dette apparat overholder det gaeldende EF-direktiv vedrørende radiostøj. Questo apparecchio è conforme al D.M.13 aprile 1989 (Direttiva CEE/87/308) sulla soppressione dei radiodisturbi. Este producto está de acuerdo con los requisitos sobre interferencias de radio frecuencia fijados por el Consejo Directivo

87/308 CEE. Dit product voldoet aan de EEG normen betreffende radio-frekwentie storingen 82/499/EEG en/of 87/308/EEG.

●

Batteries (size AA, R6, UM-3)

●

Piles (taille AA, R6, UM-3)

●

Batterien (Größe AA, R6, UM-3)

●

Batterier (storlek AA, R6, UM-3)

●

Batterie (dimensioni AA, R6, UM-3)

●

Pilas (tamaño AA, R6, UM-3)

●

Batterijen (maat AA, R6, UM-3)

●

AM Loop Antenna

●

Antenne AM à boucle

●

MW-Rahmenantenne

●

AM ramantenn

●

Antenna AM ad anello

●

Antena de cuadro de AM

●

AM Lusantenne

●

Remote Control Transmitter

●

Emetteur de télécommande

●

Fernbedienungsgeber

●

Fjärrkontrollsändare

●

Telecomando

●

Transmisor del control remoto

●

Afstandbediening

●

Indoor FM Antenna

●

Antenne FM intérieure

●

UKW-Innenantenne

●

FM inomhusantenn

●

Antenna FM per interni

●

Antena FM interior

●

FM Binnenantenne

English

Supplied Accessories ......................................2

Caution ............................................................4

Connections ....................................................5

Basic Operations .............................................8

Tuning Operations .........................................11

Preset tuning .................................................12

Receiving RDS Stations

(U.K.and Europe models only) ......................15

Remote Control Transmitter ..........................19

Notes about the Remote Control

Transmitter ....................................................20

Troubleshooting .............................................21

Specifications ................................................22

Thank you for selecting this YAMAHA stereo receiver.

FEATURES

CONTENTS

●

50W +50W (8Ω) RMS Output Power,

0.03% THD, 20 – 20,000 Hz

●

High Dynamic Power, Low Impedance Drive Capability

●

Continuously Variable Loudness Control

●

40-Station Random Preset Tuning

●

Automatic Preset Tuning

●

Preset Station Shifting Capability (Preset Editing)

●

IF Count Direct PLL Synthesizer Tuning System

●

Pure Direct Switch to Reproduce the Purest Source Sound

●

Remote Control Capability

<U.K. and Europe models only>

●

Multi-Functions for RDS Broadcast Reception

1. To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2. Install this unit in a cool, dry, clean place – away from windows,

heat sources, sources of excessive vibration, dust, moisture and cold. Avoid sources of humming (transformers, motors). To prevent fire or electrical shock, do not expose the unit to rain or water.

3. Never open the cabinet. If something drops into the set, contact

your dealer.

4. Do not use force on switches, controls or connection wires. When

moving the unit, first disconnect the power plug and the wires connected to other equipment. Never pull the wires themselves.

5. The openings on the cabinet assure proper ventilation of the unit.

If these openings are obstructed, the temperature inside the cabinet will rise rapidly. It may not only damage the unit, but also cause fire. Therefore, avoid placing objects against these openings, and install the unit where the flow of air through the ventilation openings could not be impeded, allowing a space of at least 10 cm above the top panel of the unit.

6. Always set the VOLUME control to “0” before starting the audio

source play. Increase the volume gradually to an appropriate level after playback has been started.

7. Do not attempt to clean the unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

8. Be sure to read the “TROUBLESHOOTING” section regarding

common operating errors before concluding that the unit is faulty.

9. When not planning to use this unit for long periods of time (ie.,

vacation, etc.), disconnect the AC power plug from the wall outlet.

10.To prevent lightning damage, disconnect the AC power plug and

disconnect the antenna cable when there is an electrical storm.

11.Grounding or polarization – Precautions should be taken so that

the grounding or polarization of an appliance is not defeated.

12.AC outlet

Do not connect audio equipment to the AC outlet on the rear panel if that equipment requires more power than the outlet is rated to provide.

13.Voltage Selector (General Model only)

The voltage selector on the rear panel of this unit must be set for your local main voltage BEFORE plugging into the AC main supply. Voltages are 110/120/220/240V AC, 50/60 Hz.

IMPORTANT

Please record the serial number of this unit in the space below. Serial No.: The serial number is located on the rear of the unit.

Retain this Owner’s Manual in a safe place for future reference.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS unit TO RAIN OR MOISTURE.

For U.K. customers

If the socket outlets in the home are not suitable for the plug supplied with this appliance, it should be cut off and an appropriate 3 pin plug fitted. For details, refer to the instructions described below. Note: The plug severed from the mains lead must be destroyed, as a plug with bared flexible cord is hazardous if engaged in a live socket outlet.

SPECIAL INSTRUCTIONS FOR U.K.MODEL

IMPORTANT:

The wire in the mains lead are coloured in accordance with the following code:

Blue: NEUTRAL Brown: LIVE

The colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug. Proceed as follows: the wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. Making sure that neither core is connected to the earth terminal of the three pin plug.

FREQUENCY STEP switch (General Model only)

Because the interstation frequency spacing differs in different areas, set the FREQUENCY STEP switch (located at the rear) according to the frequency spacing in your area. Before setting this switch, disconnect the AC power plug of this unit from the AC outlet.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

The apparatus is not disconnected from the AC power source as long as it is connected to the wall outlet, even if the apparatus itself is turned off.

English

ANTENNA CONNECTIONS

●

Each antenna should be connected to the designated terminals correctly, referring to the following figure.

●

Both AM and FM indoor antennas are included with this unit. In general, these antennas will probably provide sufficient signal strength. Nevertheless, a properly installed outdoor antenna will give clearer reception than an indoor one. If you experience poor reception quality, an outdoor antenna may result in improvement.

Connecting the AM loop antenna

* The AM loop antenna should be placed apart from the main unit. The antenna may be hung on a wall. * The AM loop antenna should be kept connected, even if an outdoor AM antenna is connected to this unit.

GND terminal

For maximum safety and minimum interference, connect the GND terminal to a good earth ground. A good earth ground is a metal stake driven into moist earth.

Notes

●

When connecting the indoor FM antenna, insert its connector into the FM ANT terminal firmly.

●

If you need an outdoor FM antenna to improve FM reception quality, either 300-ohm feeder or coaxial cable may be used. In locations troubled by electrical interference, coaxial cable is preferable.

CONNECTIONS

Indoor FM antenna (included)

Ground

Outdoor FM antenna

75-ohm/300-ohm antenna adapter

75-ohm coaxial cable

300-ohm feeder

ANT

UNBAL.

ANT

GND

TAPE

AM loop antenna (included)

Orient so that the best reception is obtained.

➀

➁

➂

Outdoor AM antenna

ANT

UNBAL.

AM ANT

GND

AUDIO SIGNAL

TAPE PB

REC OUT

TAPE 2

TAPE 1

AUX

PHONO

GND

LINE IN

LINE OUT

LINE IN

LINE OUT

OUTPUT

4 4

Connect the SPEAKERS terminals to your speakers with wire of the proper gauge, cut to be as short as possible. If the connections are faulty, no sound will be heard from the speakers. Make sure that the polarity of the speaker wires is correct, that is, + and – markings are observed. If these wires are reversed, the sound will be unnatural and will lack bass.

Do not let the bare speaker wires touch each other and do not let them touch the metal parts of this unit as this could damage this unit and/or speakers.

●

One or two speaker systems can be connected to this unit. If you connect only one speaker system, connect it to either the SPEAKERS A or B terminals.

●

Use speakers with the specified impedance shown on the rear of this unit.

CONNECTING SPEAKERS

A+B:l2ΩMIN. /SPEAKER

A OR B: 6

Ω

MIN. /SPEAKER

SPEAKERS

GND

SWITCHED

100W MAX. TOTAL

LeftRight

Speakers A

Speakers B

Right

Left

* : Refer to “ABOUT THE ACCESSORY

TERMINALS” on page 7.

Before attempting to make any connections to or from this unit, be sure to first switch OFF the power to this unit and to any other components to which connections are being made.

AUDIO CONNECTIONS

When making connections between this unit and other components, be sure all connections are made correctly, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Also, refer to the owner’s manual for each component to be connected to this unit.

* For a system connection with YAMAHA CDX-10 and KX-10 (or KX-W10), connections can be made easily by making sure to

connect the output (or input) terminals of each component to the same-numbered terminals of this unit.

Turntable

Compact disc player

Video cassette player, LD player, etc.

Tape deck 2

Tape deck 1

(General model)

English

How to Connect:

Red: positive (+) Black: negative (–)

➀

Unscrew the knob.

➁

Insert the bare wire. [Remove approx. 5mm (1/4”) insulation from the speaker wires.]

➂

Tighten the knob and secure the wire.

<General model only

Banana Plug connections are also possible. Simply insert the Banana Plug connector into the corresponding terminal.

ABOUT THE ACCESSOR Y TERMINALS

AC OUTLET(S) (SWITCHED)

(Europe and General models)...........2 SWITCHED OUTLETS

(U.K. model) ........................................1 SWITCHED OUTLET

Use these to connect the power cords from your components to this unit. The power to the SWITCHED outlets is controlled by this unit’s POWER switch or the provided remote control transmitter’s POWER key. These outlets will supply power to any component whenever this unit is turned on. The maximum power (total power consumption of components) that can be connected to the SWITCHED AC

OUTLET(S) is 100 watts.

GND terminal (For turntable use)

Connecting the ground wire of the turntable to this terminal will normally minimize hum, but in some cases better results may be obtained with the ground wire disconnected.

GND

+ 16 hidden pages