YAMAHA HAF3-S18W User Manual

ARRAY FRAME
HAF3-S18(W)
Thank you for choosing this Yamaha product.
Please read this manual carefully before using it in a speaker installation.
Keep the manual in safe place for future reference.
Package Contents
HAF3-S18(W)
3-1171 Angle indicator plates (2 pcs.)
3-1174 Rear joiner plate (2 pcs.)
3-0235 M10-40mm button head socket screws (14 pcs.)
2-1432 M10 flat washers (16 pcs.)
3-0112 M10 L-key wrench (1 pc.)
Owner’s Manual
NOTE
• Use only the eye bolts included with the speaker unit.
• For information on load limits and the strength of the eyebolt, refer to the owner's manual of the speaker.
EN
PRECAUTIONS
CAUTION
Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the device or other property. These precautions include, but are not limited to, the following:
• Before doing any installation or construction work, consult with an installation expert.
• Make sure that the surface this bracket is being mounted on has the strength to handle the weight of both the speaker and this bracket.
• Use bolts and nuts as well as washers for installation and tighten them firmly so that the speaker is secure and does not move.
• Always loosen the corresponding screw before adjusting the angle or direction of the speaker. Never force this adjustment with the screw still tightened.
• Some fittings may deteriorate over extended periods of time due to wear and/or corrosion. For optimum safety, the installation should be checked thoroughly at regular intervals.
Yamaha cannot be held responsible for damage or injury caused by insufficient strength of the support structure or improper installation.
* Illustrations herein are for explanatory purposes only, and may not match actual appearance during operation.
* Company names and product names herein are trademarks or registered trademarks of their respective companies.
* Specifications and descriptions in this owner's manual are for information purposes only. Yamaha Corp. reserves the right to
change or modify products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer.
PLEASE READ CAREFULLY BEFORE PROCEEDING
* Please keep this manual in a safe place for future reference.
Installation Instructions
1. Flip the speakers upside down. Remove the existing
speaker screws.
2. Determine the splay angle of the speaker and the holes to
use on the front joiner plate.
with the provided screws and flat washers. Install an angle indicator plate on the front inserts using the corresponding holes for the appropriate splay angles with the screws and flat washers. Tighten permanently.
4. Carefully flip the assembly to expose the top of the
speakers.
with the provided screw and flat washer on the center speaker and the two eye bolts on the side speakers. Install an angle indicator plate on the front inserts using the corresponding holes for the appropriate splay angles with the screws and flat washers on the center speaker and the two eye bolts on the side speakers. Tighten permanently.
6. Use the two eye bolts on the rear of the speaker cluster and
the two eye bolts on the front to suspend the speaker cluster.
M10 Flat Washer [TYP]
Angle Indicator Plate (3-1171)[2X]
M10 EyeBolt [4X]
Rear Joiner Plate (3-1174)[2X]
30°
M10 Screw [TYP]
Dimensions
3-1171 Angle Indicator Plate
7.73
3-1174 Rear Joiner Plate
φ.402 28X
3.76
.406 DIA X 30°SLOT 2X
φ.53 2X
20.75
49.48
φ.402
7. For steep tilt angles, move the rear eye bolts to the rear
bottom insert of the speaker cluster and use as a pull back point. Make sure to replace the eye bolts with the provided screws and washers.
90°
90° Maximun Splay Configuration
Tight Pack Configuration
6.78
37.68
40.47
Loading...