Page 1
420F and 429F Series Trim
Installation Instructions
For use with Yale® 7000, 2100, 1800
and 1500 Series Exit Devices
(Wood and Metal Doors)
2-1/2"
Attention Installer
Any retrofit or other field modification to a fire rated opening can
potentially impact the fire rating of the opening, and Yale Locks &
Hardware makes no representations or warranties concerning
what such impact may be in any specific situation. When
retrofitting any portion of an existing fire rated opening, or
specifying and installing a new fire-rated opening, please consult
with a code specialist or local code official (Authority Having
Jurisdiction) to ensure compliance with all applicable codes and
ratings.
429F Series
Dummy Trim
Handed (RHR or LHR)
Rigid Lever
An ASSA ABLOY Group brand
9-1/2"
420F Series
Blank Trim
Non-Handed
80-8470-0420-000 (01-13)
Page 2
Outside Door
Face
5/16" (8) Dia.
1/2" (13) Dia.
1/2" (13) Dia. Thru
CAUTION: Office copiers and
facsimile machines may change
the size of a drawing and make
the template inaccurate to use as
a door marker.
If this is not the original template
packed with the trim, use only the
holes on the door (do not use
template as a door marker).
C
L
HORIZONTAL
REFERENCE
C
(Device and Trim)
L
420F
429F
An ASSA ABLOY Group brand
2
80-8470-0420-000 (01-13)
Page 3
Trim Components
420F Series
Blank Trim
Escutcheon Assembly
2 STUDS TOWARDS
LOCK EDGE
(2) 1/4-20 Pan Head
Machine Screws
Packed with device
2 STUDS AWAY
2 STUDS AWAY
FROM LOCK EDGE
FROM LOCK EDGE
429F Series
Dummy Trim
Escutcheon Assembly
Lever is handed RHR (shown) or LHR
To Change Handing:
Remove cotter pin, nut, hub, and gear. Rotate
lever for opposite handing. Reassemble gear
with teeth engaging set screw to lock lever in
place. Reassemble hub, nut, and cotter pin.
(2) #14 Finishing Washers
(2) 1/4-20 Oval Head
(2) 1/4-20 Oval Head
Machine Screws
Machine Screws
2 STUDS TOWARDS
LOCK EDGE
(2) 1/4-20 Pan Head
Machine Screws
Packed with device
An ASSA ABLOY Group brand
(2) #14 Finishing Washers
2 STUDS AWAY
2 STUDS AWAY
FROM LOCK EDGE
FROM LOCK EDGE
(2) 1/4-20 Oval Head
(2) 1/4-20 Oval Head
Machine Screws
Machine Screws
80-8470-0420-000 (01-13)
3
Page 4
Installation Instructions
1. Check box for contents. See page 3 for components
and instructions.
2. After marking door inside face for device location
(Device Instructions), transfer Vertical Reference
Centerline from inside to outside door face. Follow
steps 2a and 2b below.
3. Transfer Horizontal Reference Centerline from inside
to outside door face.
4. Align trim template and tape to outside door face.
CAUTION: Office copiers and facsimile machines
may change the size of a drawing and make the
template inaccurate to use as a door marker. If this is
not the original template packed with the trim, use
only the dimensions written on the template to locate
the holes on the door (do not use the template as a
door marker).
5. Spot holes and prepare door for trim.
6. Mount trim to door thru holes "B". Fasten finger tight
only with (2) screws and washers seating on door as
shown in Figure 1.
7. Continue as shown in device instructions.
Device is bolted
to trim using
holes "A" (closest
A
to door lock edge).
A
(2) Screws and
washers bolt trim
to door using
holes "B".
Product Support Tel 800.438.1951 • www.yalelocks.com
Yale Locks & Hardware is a division of Yale Security Inc., an ASSA ABLOY Group company.
Yale® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company. Other products' brand names may be trademarks or registered trademarks of their
respective owners and are mentioned for reference purposes only. These materials are protected under U.S. copyright laws. All contents current at time of publication.
Yale Security Inc. reserves the right to change availability of any item in this catalog, its design, construction, and/or its materials.
All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.
Copyright © 2008, 2013, Yale Security Inc., an ASSA ABLOY Group company.
4
An ASSA ABLOY Group brand
80-8470-0420-000 (01-13)
Loading...