Page 1
Handbuch
Manual
Manuel
Yakumo 32" LCD TV
LCD TV
DFGB E I
Page 2
Explanation of WARNING Symbols
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence dangerous
voltage within the inside of the product that may be sufficient
level to constitute a risk of electric shock.
English
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and
servicing instructions.
Safety instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this Yakumo 32” LCD TV near water.
6) Clean only with dry cloth. Do not use liquid, alcohol, or aerosol cleaners.
7) Do not block any ventilation openings. Install your Yakumo 32” LCD TV
in a well ventilated area.
8) Keep your Yakumo 32” LCD TV away from moisture, excessive dust
and any heat sources, such as radiators, heat registers, stoves, or any
other apparatus (including amplifiers) that produce heat.
9) Do not remove the back cover. There are no user-serviceable parts
inside.
10) Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the other. A
grounding type plug has two blades and a third grounding prong. The
third prong is provided for your safety. If the provided plug does not fit
into your outlet, consult an electrician for replacement of the obsolete
outlet.
11) Protect the power cord from being walked on or pinched particularly at
plugs, receptacles, and the point where they exit from the Yakumo 32”
LCD TV.
12) Never rest objects on the power cord or place it in high traffic
areas.
13) Only use attachments/accessories specified by the manufacturer.
14) Use only with stand, tripod, bracket, or table specified by the
manufacturer, or sold with the Yakumo 32” LCD TV. When a cart is
used, use caution to avoid injury from tip-over.
15) Unplug this Yakumo 32” LCD TV during lightening storms or when
unused for long periods of time.
Manual
Page 3
16) Refer all servicing to qualified service personnel-- Servicing may be
required if the Yakumo 32” LCD TV has been damaged in any way,
such as power-supply cord or plug damage, liquid has been spilled or
objects have fallen into the Yakumo 32” LCD TV, the Yakumo 32” LCD
TV has been exposed to rain or moisture, does not operate normally, or
has been dropped.
17) Do not expose your Yakumo 32” LCD TV to dripping or splashing, and
do not place objects filled with liquids on it.
Englishnglish
18) The Shock Hazard Marking and Associated Graphical Symbol are
provided on the back panel of unit.
19) This product is only to perform the useful function of entertainment and
should not be used in an industrial application.
20) Wall or ceiling mounting: When mounting the product on a wall or
ceiling, be sure to install the product according to the method
recommended by the manufacturer. Use only the mounting hardware
recommended by the manufacturer. This is a safety feature.
CAUTION: Any damage caused by incorrectly attempting to mount
this Yakumo 32” LCD TV is not covered under the terms of the
manufacturers
warrant
y
.
WARNING: To reduce the risk of fire or electric shock, do not expose
this Yakumo 32” LCD TV to rain or moisture.
According to WEEE regulation , this monitor can't be handled as normal
trash in Europe when it is out of usage. Please refer to the recycle
information from our website to handle it.
www.yakumo.com
Manual
Page 4
Content
PACKAGE CONTENTS AND ACCESSORIES.................................................. 1
FRONT PANEL BUTTONS................................................................................. 2
BACK PANEL BUTTONS and I/O Interfaces...................................................... 3
REMOTE CONTROL ......................................................................................... 4
INSTALLATION .................................................................................................. 8
English
Connecting RF antenna or Cable TV Wire.................................................. 8
Connecting with Stereo Audio Out cable..................................................... 8
Connecting with AV Audio/ Video cable....................................................... 8
Connecting with D-SUB VGA cable-HD compatible .................................. 10
Connecting to the Headphone................................................................... 10
Connecting with PC Audio In cable/ D-SUB Audio-IN ................................11
Connecting to a Computer with HDMI-DVI cable .......................................11
Connecting with the power cord.................................................................11
BASIC OPERATION......................................................................................... 12
Turning on the Yakumo 32” LCD TV.......................................................... 12
Power On/Off ............................................................................................ 12
Select input source.................................................................................... 12
Volume Adjusting....................................................................................... 12
Channel Select.......................................................................................... 12
Sleep Time Setting .................................................................................... 12
PIP and POP Screen................................................................................. 12
Sound........................................................................................................ 13
Video ......................................................................................................... 14
Using OSD Menu ...................................................................................... 14
ADVANCED OPERATION—OSD MENU/ REMOTE CONTROL ..................... 15
Picture Menu ............................................................................................. 15
Sound Menu.............................................................................................. 15
Channel Menu........................................................................................... 17
Option Menu.............................................................................................. 19
PC Menu ................................................................................................... 19
OSD Menu ................................................................................................ 20
TECHNICAL SPECIFICATION......................................................................... 21
SAFETY PRECAUTIONS................................................................................. 22
CARE AND MAINTENANCE ............................................................................ 23
TROUBLESHOOTING ..................................................................................... 23
Manual
Page 5
PACKAGE CONTENTS AND ACCESSORIES
Package contents:
Thank you for purchasing this LCD-TV.
This LCD-TV package comes with:
User’s Guide book
Remote control
Battery AA x 2
Power cable
OPTIONAL
ACCESSORIES:
You can purchase these optional accessories for your
Yakumo 32”
LCD TV:
HDMI cable
S-Video cable
PC Audio cable
VGA cable
SCART cable
Video cable
Component (Ypbpr,Ycbcr) cable
Wall mount kit (Vesa 400x200)
1
Englishnglish
Manual
Page 6
FRONT PANEL BUTTONS
X Y Z [ \ ]
^ _ `
Volume - Down
Volume + Up
On Screen Display Menu On/Off
Channel Down (Scroll Down)
Channel Up (Scroll Up)
Enter
Power ON/OFF
Power LED Indicator
❾ Remote Control Receiver
2
English
Manual
Page 7
BACK PANEL BUTTONS AND I/O INTERFACES
A
B
C
D
E
F
G
H I J K L M N O
A RF Antenna / Cable TV Input
B Composite Video input
C S-Video Input
D Component Video Input (YPbPr/ Ycbcr)
E Audio Input for AV or S-Video Components (left/ right)
F Audio Input for Component Video (left/ right)
G Audio Output (left/ right)
H AC Power Switch (Must be turned on)
I Power Input (AC Input)
J HDMI (support HDCP)
K D-SUB (15 pin) Signal Input from Computer
L Audio Input for VGA
M Headphone Jack
N SCART2 / SCART2-SV Input
O
SCART 1 Input
3
Englishnglish
Manual
Page 8
REMOTE CONTROL
4
English
Manual
Page 9
Remote control button function as follows：
1 POWER Power ON/OFF
2 LED Power LED Indicator
3 MUTE Volume mute ON/OFF
4 SOURCE Input source select (for main screen)
5 INFO Display the current information
6 POP POP ON/OFF
7 PIP PIP ON/OFF
8 P. SOURCE Input source select (for PIP/POP sub-screen)
9 P. SIZE Adjust the size for PIP/POP sub-screen
10 V+ Adjust PIP/POP sub-screen’s volume increasingly
11 V- Adjust PIP/POP sub-screen’s volume decreasingly
12 P+ Select up program for PIP/POP sub-screen
13 P- Select down program for PIP/POP sub-screen
14 SWAP Swap main and sub screen of PIP/ POP
15 P. POS Adjust PIP/POP sub-screen’s position
16 RED Move the cursor (It is active in Name and Teletex function)
17 GREEN In Teletex function: move cursor up
In Name function: add desired channels
18 YELLOW In Teletex function: change from current page to selected page
In Name function: erase desired channels
19 BLUE In Teletex function: go out from CURSOR Mode
In Name function: confirm edited name
20 VOL UP/ DOWN Adjust volume up or down
21 SMART. S Select situation mode for sound
22 SMART. P Select situation mode for picture
23 PROGRAM UP/ DOWN Select up or down programs
24 MENU OSD menu ON/OFF
25 ASPECT Aspect ratio, used to select image size
26 UP/ DOWN/ LEFT/ RIGHT Select or adjust the function of OSD
27 ENTER Confirm the selection
28 AVC The tuner contains automatic volume control circuitry (AVC) to
prevent converter overload
29 M S SOUND Sound select between main screen and sub-screen
30 0~9 NUMBER Switch channel number keys
31 SLEEP Set TV Sleep timer
32 FLASHBACK Return to previos channel
33 DUAL I / II MTS (Multi-Channel TV Sound) select (TV-mode only)
34 FREEZE Freeze picture (TV-mode only)
35-43 TELETEXT FUNCTION
CONTROL button
Please refer to page 6~7 (TV-mode only)
Note: PIP means Picture In Picture, POP means Picture Out Of Picture.
5
Englishnglish
Manual
Page 10
Teletext function control button
TEXT/ MIX/ PICTURE button
In TV Mode: Press the TEXT/ MIX/ PICTURE button to enter the Teletext mode.
In TELETEXT Mode: Press the button again to superimpose a Teletext Broadcast
onto the screen of current TV program (mixed Mode).
In MIXED Mode: Press the button again to return back to the normal TV Screen
(current program).
INDEX button
Press the Index button to return back to index page.
When you press this button in teletext mode, a CURSOR appears. This cursor
(rectangular box) contains a page number and you can select the desired page
simply by using the four colours.
RED button: Move cursor down.
GREEN button: Move cursor up.
YELLOW button: Change from current page to selected page.
BLUE button: Exit the CURSOR Mode.
LIST button
Press this button you force the Teletext to LIST Mode. It means that row 24 (bottom
row of Teletext) will not have transmitting information, only the pages that you have
previously stored in the memory.
Press LIST button again to exit from LIST Mode to teletext.
REVEAL button
Press this button to display concealed information, such as solutions of riddles or
puzzles.
Press this button again to remove the information from the display.
STORE button
Store current page in List mode.
Press the LIST button to change from FLOF system to LIST Mode.
Press a coloured button corresponding to the coloured brackets on the screen for
page number storage.
Enter the Teletext page number using the 0 ~ 9 digit buttons (enter three digits).
Press the STORE button to memorize the page numbers you require.
6
English
Manual
Page 11
HOLD button
Press this button to remove the information from the display and stop the automatic
page change which will occur if a teletext page consists of 2 or more sub pages.
To continue press this button again. The number of sub pages and the sub page
displayed is, usually, shown on the screen below the time. When this button is
pressed the stop symbol is displayed at the left-top corner of the screen and the
automatic changing is inhibited.
SIZE button
Select double height text under Teletext mode for full screen.
Press this button to enlarge the top half of the page.
Press this button again to enlarge the bottom half of the page.
Press this button again to return to the normal display.
LANGUAGE button
Press this button to select the language of Teletex function between English,
Cyrillic and Arabic.
SUBCODE button
When a selected Teletext page with hidden sub pages or timed pages, these pages can
be seen by the following manner:
Press the sub code button. Screen will show « = = = = »
Enter 4 digits number button corresponding to the sub page desired. E.g. 0010 for
sub page number 10.
Wait until the page appears.
7
Englishnglish
Manual
Page 12
INSTALLATION
Connecting RF antenna or Cable TV Wire
Make sure the power is OFF before installing your Yakumo 32” LCD TV. Connect the
Yakumo 32” LCD TV to TV antenna wire or cable/satellite box with 75-ohm coaxial
cable.
Preset the TV channels into memory with AUTO SCAN function when using an
antenna or cable TV system without a cable connecter box. See page 16.
Connecting with Stereo Audio Out cable
Connect the audio output terminal of the Yakumo 32” LCD TV to audio in
terminal of the
stereo system (stereo system sold separately).
Connecting with AV Audio/ Video cable
Connect Video/ Audio cables from compatible devices into the back panel of
LCD TV.
1) With RCA A/V cable
RF Cable or Adapter
(not supplied)
Stereo system
A
udio in Cable (not supplied)
Video Cable (not supplied)
VCR or DVD Playe
r
8
English
Manual
Page 13
2) Connecting with S-Video cable:
3) Connecting with Component cable (YPbPr,Ycbcr)-HD compatible:
4) Connecting with SCART cable on SCART 1:
5) Connecting with SCART cable on SCART2/ SCART2-SV/ S-Video compatible:
Note:
S-Video Cable (not supplied)
A
udio in Cable
(not supplied)
VCR or DVD Playe
r
YPbPr Cable (not supplied)
A
udio in Cable
(not supplied)
VCR or DVD Player
SCART Cable (not supplied)
VCR or DVD Player
SCART Cable (not supplied)
Set top or DVD Player
Acceptable Signal Available Provided Input Source
SCART1 AV/RGB TV only
SCART2 AV/RGB All (CVBS signal)
SCART2-SV S-Video All (CVBS signal)
9
Englishnglish
Manual
Page 14
6) Connecting with HDMI cable- HD compatible:
Connecting with D-SUB VGA cable-HD compatible
Connect the VGA cable from VGA output of computer to the VGA terminal
input of your LCD TV.
Computer up to 1360 x 768 is the preferred resolution.
Connecting to the Headphone
Connect the headphone to the headphone output terminal of the Yakumo 32”
LCD TV.
(Headphone sold separately)
(DVD Player should
have the HDMI
Output terminal)
VCR or DVD Playe
r
HDMI Cable (not supplied)
PC
VGA 15 Pin Cable (not supplied)
Headphone
(not supplied)
10
English
Manual
Page 15
Connecting with PC Audio In cable/ D-SUB Audio-IN
Connect the Audio In cable (green) from audio output of your computer to the
audio input terminal (green) of the Yakumo 32” LCD TV.
PC
Connecting with the power cord
Connect the power cord to the power cord connector on the back of your
Yakumo 32” LCD TV, and plug the other end of the power cord into a correctly
grounded electrical outlet.
PC Audio Out Connection (not supplied)
AC Switch
Switch to ON
A
C wall Switch
11
Englishnglish
Manual
Page 16
BASIC OPERATION
To operate your Yakumo 32” LCD TV, you may use the TV remote control or
upper panel buttons to select input source, change channels, or adjust volume.
Turning on the Yakumo 32”
LCD TV
Before using the Yakumo 32” LCD TV:
1. Insert the power cord.
2. Connect external components.
3. Turn on Main Power Switch, located on the rear of the cabinet (If the
Yakumo 32” LCD TV will not be used for a long period of time, please turn
it off).
Power On/Off
To turn the Yakumo 32” LCD TV on/off :
Press POWER button on the bottom of the cabinet or press POWER key on
your remote control to turn on/off the TV. The power LED indicator lights when
the Yakumo 32” LCD TV is on.
Select input source
Press SOURCE key and use ◄► to select the required input source between
D-SUB, HDMI, TV, Video, S-Video, Component, SCART1, SCART2,
SCART2-SV...
To confirm the selection, press (ENTER).
V olume Adjusting
Press VOL▲▼ to adjust volume.
To silence volume, press MUTE.
If you want to restore volume, press MUTE again, or press VOL▲▼ directly.
Channel Select
Press number keys, PROGRAM ▲▼ keys, or CH-/+ buttons to select the
desired channels.
Ex: the desired channel is 8--press 8 only.
Ex: the desired channel is 80--Press 8, then press 0.
Return to previous channel, press FLASHBACK key.
Sleep Time Setting
Repeatedly press SLEEP key to set the off timer. The function is used to
automatically shut off the Yakumo 32” LCD TV after a preset period of time
passed.
There are several times for choice -- 15min, 30min, 45min, and 60min.
To cancel Sleep Time function, choose 0 min.
PIP and POP Screen
Display PIP Screen and POP Screen
PIP screen and POP screen allow you watch two screens from different
sources at the same time.
NOTE: PIP is picture in picture; POP is picture out of picture.
Press PIP or POP key on remote control to display main and sub-screen at
the same time.
12
English
Manual
Page 17
PIP Screen :
POP Screen：
PIP/POP Input Source Select
1. Press P. SOURCE to select input source for sub-screen as following,
Main Screen Input Source of Sub-Screen
D-SUB/ TV/ Video/ S-Video/ SCART1/ SCART2/
SCART2-SV
D-SUB/ HDMI/ Component
D-SUB/ HDMI/ Component TV/ Video/ S-Video / SCART1/ SCART2/
SCART2-SV
2. Press ENTER to confirm selection.
PIP Size Select
Press P.SIZE to select the size of sub-screen. The function is only available
in PIP.
Swap main and sub screen of PIP/ POP
Press SWAP to exchange main-screen to sub-screen.
PIP Position
To setup the position of sub-screen. This function is only available in PIP.
Adjust Volume of Sub-screen
Press V+ and V- to adjust volume of sub-screen.
Select Program for Sub-screen
Press P+ and P- to select the program of sub-screen. (TV mode only)
Sound
Sound Mode Select
Continue to press SMART.S to select the sound mode between Movie,
Music, Speech, and User.
Sound Source Select
Continue to press M S Sound to select the sound source between main
screen and sub-screen.
MTS Select
Press DUAL I / II key to set up MTS system.
The function is to provide multi-channel TV sound. MTS can receive Dual,
Stereo, SAP (Secondary Audio Program), or Mono sound. SAP feature
permits the TV station to broadcast other information, such as audio in
13
Englishnglish
Manual
Page 18
another language. With Dual sound, you can enjoy the main sound (normal
program soundtrack) and the second language at the same time.
**Choose the available sound output for channels that is preset by TV
broadcasting station.
Program’s sound setting Exchangeable sound output
dual dual I, dual II
stereo stereo, mono
mono mono
Video
Picture Mode Select
Continue to press SMART.P key to select picture mode between Movie,
Vivid, User, and Standard.
Aspect Ratio Select
Continue to press ASPECT key to select image size between Zoom1,
Zoom2, Normal, Panorama, and Full.
In POP screen, image size of main screen is only for Full.
Freeze Picture
Press FREEZE key to freeze picture. However, the sound still continues.
(TV mode only)
Using OSD Menu
You are able to use On Screen Display (OSD) menus to adjust various settings
by using your remote control or menu button on the top of the Yakumo 32” LCD
TV.
The basic operation is as following:
Press MENU to display OSD menu.
Use ▲▼ to move cursor bar up and down to select OSD menu page or
adjusting items.
Press ENTER to confirm selection.
Press ◄► to adjust levels or select the items.
Press MENU again to exit current OSD page.
PS. In OSD page, if the item is with an arrow ►, it indicates that there is a
sub-OSD page with it. You have to press ◄ or ► to get into sub-OSD page.
However, if the item is with two arrows ◄(selection)►, it means that user may
just press ◄► to select the selection. There is no sub-OSD page with it.
14
English
Manual
Page 19
ADVANCED OPERATION—OSD MENU/ REMOTE CONTROL
Picture Menu
— Adjusting the picture
It is active in TV/ Video/ S-Video / Component/ SCART1/ SCART2/ SCART2-SV and
HDMI source.
Contrast: To adjust contrast of video.
Brightness: To adjust luminance of video.
Colour: To adjust colour.
Tint: To adjust tint level.
Sharpness: To adjust picture sharpness.
Fresh Tone: To adjust colour of skin.
Colour Temp.: To select colour Temp. by pressing ◄►—warm redder, normal neutral,
or cool bluer.
Reset: Press ENTER to reset all the settings in Picture page.
Sound Menu
—To adjust sound
It is active in all input sources.
Source: To select the sound source from main screen or sub screen by pressing ◄►.
Note: It is available in SCART1/ SCART2/ SCART2-SV. However, in other input
15
sources, it is only active when in PIP/POP condition.
Englishnglish
Manual
Page 20
Bass: To adjust bass (It is active in TV/ SCART1/ SCART2/ SCART2-SV. However, in
other input sources, it is only active when sound mode is in “User” condition).
Treble: To adjust the treble (It is active in TV/ SCART1/ SCART2/ SCART2-SV.
However, in other input sources, it is only active when sound mode is in “User”
condition).
Balance: To adjust left and right audio balance.
Reset: Press ENTER to reset all the settings in Sound page.
Channel Menu
—To setup for TV
English
It is only active in TV source.
Auto Scan: To automatically preset the channels into TVs memory by pressing ◄►.
Kindly suggest you auto scan all the channels before watching your TV for the first
time.
Note: After auto scan all the channels, you need not to do it again when turning
on your TV next time.
Manual Store: The function is to give a minute search for possible existing hem in
memory.
1. Press ◄ or ► to get into “Manual Store.”
2. Move the cursor to “Prog. No, “ and select the desired channel position with ◄►.
3. Move the cursor to “System,“ and select the system according to your local area
with◄►.
4. Move your cursor to “Search,” and search the detectable channels with ◄►.
5. Move your cursor to “Fine Tune,” and adjust the picture with ◄►.
6. Move to Store, then Store the instruction with ENTER .
Note: The channel will be stored instead of the former program.
16
Manual
Page 21
Name: To enter a name for program with 0~9, +-. /, and A~Z. Press ◄ or ► to get into
“Name.”
English
1. To enter a name:
Press red key (on the remote control) to move your cursor to “Name.”
Use ▲▼ to select the desired letter and use◄► to move the cursor to enter next
letter. To confirm the name, press blue key.
2. To Erase/ Add channels:
Use ▲▼ to select the desired channel.
Press yellow key to erase the channel or press green key to add it.
When using PROGRAM▲▼ key, the channels you erased will be passed over. You
may press green key to add the erased channels or use Auto Scan function to
re-present them.
Sort: To exchange one channel with another. Press ◄ or ► to get into “Sort.
If you want to exchange channel 1 with channel 2:
1. Move your cursor to “From” and press ◄► to select channel 1.
2. Move your cursor to “To,” and press ◄► to select channel 2.
3. Move your cursor to “Store,” and confirm the instruction with Enter .
4. Press MENU to exit.
17
Manual
Page 22
Option Menu
When input source is TV/ AV/ SV/ HD/ When input source is D-SUB/ HDMI:
SCART1/ SCART2/ SCART2-SV/ HDMI:
English
Main Source: To select the input source for main screen between TV, Video, S-Video,
Component, SCART1, SCART2, SCART2-SV, D-SUB, and HDMI with ◄►.
H-Position: To adjust the horizontal position of the video with ◄►.
V-Position: To adjust the vertical position of the video with ◄►.
Language: To select the OSD language between English, French, German, Spanish,
Italian, Dutch, etc ◄►.
Reset: Press ENTER to reset all the settings in Option page.
PC Menu
—to Adjust for PC
It is only active in D-SUB
When input source is D-SUB:
Auto Adjust: Auto adjust picture’s horizontal position, vertical position, fine tune,
and H-Size with ◄►.
Contrast: To adjust foreground luminance of video.
Brightness: To adjust background luminance of video.
H-Position: To adjust horizontal position of video.
V-Position: To adjust vertical position of video.
Clock: To adjust delay time of clock in order to reduce the noise of picture.
Phase: To adjust delay time of phase in order to reduce the noise of picture.
18
Manual
Page 23
Colour Mode: To adjust colour temperature.
English
1. Press ◄ or ► to get into Colour Mode.
2. Use ◄►to select between Cool, sRGB, User, Normal, and Warm.
3. When select “User,” it allows you separately adjust the colour of red, green, and
blue.
Reset: Press ENTER to reset all the settings in PC page.
OSD Menu
—To setup OSD window
It is active in all input sources except HDMI source.
H-Position: To adjust the OSD horizontal position with ◄►.
V- Position: To adjust the OSD vertical position with ◄►.
Duration: To automatically shut off the OSD after a preset period of time passed.
Use ◄►to preset the time from 5 to 60 seconds.
Halftone: To adjust background transparency of OSD.
Reset: Press ENTER to reset all the settings in OSD page.
19
Manual
Page 24
TECHNICAL SPECIFICATION
Type 31.51” TFT Active Matrix
0.51075(H) x 0.51075(V) mm pixel pitch
Color Filter RGB vertical stripe
LCD
Glass surface Anti-Glare
RGB RGB analog (0.7/1.0 Vp-p, 75 ohms)
Separate Sync,
fh: 30-80 kHz, fv:50-75 Hz
RF TV system Antenna / PAL
Input signal
Video 1 composite RCA, 1 S-Video, 1 YPbPr
component, HDMI, 2 SCART
Audio 1 mini-stereo, 2 pair pf RCA (L/R) stereo
Compatibility PC Up to 1360 x 768 Non-interlaced
Resolution Recommended
and supported
1360 x 768 @ 60 Hz
1280 x 1024 @ 60 Hz, 75 Hz
1024 x 768 @ 60, 75 Hz
800 x 600 @ 60, 75 Hz
640 x 480 @ 60, 75 Hz
Speaker Output 10W x 2
Audio Output 1 pair of RCA (L/R) stereo jack
Power Voltage 100-240 VAC, 50/60 Hz (auto switch)
Display area Full Scan 697.68 mm (H) x 392.25 mm (V)
27.5” (H) x 15.4” (V)
Temperature 32°F to + 104°F ( 0°C to + 40°C)
Humanity 10% to 65% (no condensation)
Operating
conditions
Altitude To 10,000 feet (3,000m)
Temperature -4°F to + 140°F (-20°C to + 60°C)
Humanity 10% to 90% (no condensation)
Storage condition
Altitude To 40,000 feet (12,000m)
Dimensions Physical 807.7mm (W) x 646.2mm (H) x 210mm (D)
31.8’’ (W) x 25.4’’ (H) x 8.3’’ (D)
Weight Net 21.8 kg (48.0 Ib)
Regulations CE, Class B
On < 200 W (green LED) Power saving modes
Active Off < 5 W (red LED)
Preset Timing Mode (Pre-adjusted to GTF® 1360 x 768 @ 60 Hz)
Warning: Do not set the graphics card in your computer to exceed these refresh rates;
doing so may result in permanent damage to the LCD TV
English
20
Manual
Page 25
SAFETY PRECAUTIONS
This
Yakumo 32”
LCD TV is manufactured and tested to insure the user’s
safety. Improper use or installation may result danger to the
Yakumo 32”
LCD
TV as well as to the user. Carefully go over the following WARNINGS before
installation and keep this guide handy.
English
WARNINGS
This Yakumo 32” LCD TV should be operated only at the correct power sources
indicated on the label on the rear end of the Yakumo 32” LCD TV. If you’re unsure
of the power supply in your residence, consult your local dealer or power
company.
Do not try to repair the
Yakumo 32”
LCD TV yourself as it contains no
user-serviceable parts. The
Yakumo 32”
LCD TV
should only be repaired by a
qualified technician.
Do not remove the
Yakumo 32”
LCD TV cabinet. There is high-voltage parts inside
that may cause electric shock. even when the power cord is disconnected .
Stop using the
Yakumo 32”
LCD TV if the cabinet is damaged. Have it checked by
a service technician.
Put your
Yakumo 32”
LCD TV only in a clean, dry environment. Unplug the
Yakumo 32”
LCD TV immediately if gets wet and consult your service technician.
Always unplug the
Yakumo 32”
LCD TV before cleaning it. Clean the cabinet with
a clean, dry cloth. Apply non-ammonia based cleaner onto the cloth, not directly
onto the glass screen.
Keep the
Yakumo 32”
LCD TV away from magnetic objects, motors, TV sets, and
transformer.
Do not place heavy objects on the cable or power cord.
For PLUG CABLE EQUIPMENT, the Socket-outlet shall be installed near the
equipment and shall be easily accessible.
21
Manual
Page 26
CARE AND MAINTENANCE
Care
Avoid exposing your
Yakumo 32”
LCD TV directly to sunlight or other heat
source.
Place your
Yakumo 32”
LCD TV away from the sun to reduce glare.
Put your
Yakumo 32”
LCD TV in a well ventilated area. Do not place anything
heavy on top of your
Yakumo 32”
LCD TV.
English
Make certain your
Yakumo 32”
LCD TV is installed in a clean and moisture-free
area.
Keep your
Yakumo 32”
LCD TV away from magnets, motors, transformers,
speakers, and TV sets.
Safety Tips
If smoke, abnormal noise or odor came out of your
Yakumo 32”
LCD TV, caution
should be remove the power cord immediately and call your service center.
CAUTION-Never remove the rear cover of your
Yakumo 32”
LCD TV cabinet.
The display unit inside contains high-voltage parts and may cause electric shock
to human bodies.
Never try to repair your
Yakumo 32” LCD TV yourself. Always call your service
center or a qualified technician to fix it.
TROUBLESHOOTING
No power
Make sure A/C power cord is securely connected.
Plug another electrical device into the power outlet to verify that the outlet is
supplying proper voltage.
Power on but no screen image
Make sure the video cable supplied with the TV is tightly secured to the video
output port on back of video source (DVD, VCR…). If not, tightly secure it.
Adjust brightness.
Make sure all signal cables are installed.
Wrong or abnormal colors
If any colors (red, green, blue) are missing, check the video cable to make sure it
is securely connected. Loose or broken pins in the cable connector could cause
an improper connection.
Connect the TV unit to another video source or use another TVs to make sure
the video source was not causing the problem.
22
Manual
Page 27
www.yakumo.com
Loading...