Yaesu Musen 20445X20 User Manual

Download

Page 1

Set Mode

ApplicationforFCC/IC

FCCID:K6620445X20

IC:511B-20445X20

Set mode option No./

setting Item

9-6 APRS MSG GROUP Set group filter for receiving mes-

9-7 APRS MSG TXT Enter standard message text 1 to

9-8 APRS MUTE Turn on/off the B-band AF muting

9-9 APRS POPUP Set such as a beacon type, mes-

Description of function

sages.

7ch

function when APRS is set.

sage type and time for pop-up display.

Functions Used As Needed

Setting Item

(Bold letters: Default)

G1: ALL******

G2: CQ******* G3: QST****** G4: YAESU**** G5: B1: BLN****** B2: BLN* B3: BLN*

1 to 8 ch –

ON / OFF –

Mic-E: OFF / ALL2s to ALL60s / ALLCNT / BND2s to BND60s /

BNDCNT ALL10s POSITION: OFF / ALL2s to ALL60s / ALLCNT / BND2s to BND60s /

BNDCNT ALL10s WEATHER: OFF / ALL2s to ALL60s / ALLCNT / BND2s to BND60s /

BNDCNT ALL10s OBJECT: OFF / ALL2s to ALL60s / ALLCNT / BND2s to BND60s /

BNDCNT ALL10s ITEM: OFF / ALL2s to ALL60s / ALLCNT / BND2s to BND60s /

BNDCNT ALL10s STATUS: OFF / ALL2s to ALL60s / ALLCNT / BND2s to BND60s /

BNDCNT ALL10s OTHER: OFF / ALL2s to ALL60s / ALLCNT / BND2s to BND60s /

BNDCNT ALL10s MY PACKET: OFF / ALL2s to ALL60s / ALLCNT / BND2s to BND60s /

BNDCNT ALL10s MSG: OFF / ALL2s to ALL60s / ALLCNT / BND2s to BND60s /

BNDCNT ALL10s

Reference

page

–

100

Page 2

Set Mode

ApplicationforFCC/IC

FCCID:K6620445X20

IC:511B-20445X20

Set mode option No./

setting Item

9-9 APRS POPUP Set the beacon type, the message

9-10 APRS RINGER Turn on/off the bell when a bea-

9-11 APRS UNIT Select the units for APRS display. Position: MM.MM' / MM'SS'

9-12 APRS TX DELAY Set the data sending delay time. 100ms / 150ms / 200ms /

Description of function

type and the time of the popup display.

con is received.

GRP: OFF / ALL2s to ALL60s / ALLCNT / BND2s to BND60s /

BLN: OFF / ALL2s to ALL60s / ALLCNT / BND2s to BND60s /

MY MSG: OFF / BND2s to BND60s /

DUP.BCN: OFF / BND2s to BND60s /

DUP.MSG: OFF / BND2s to BND60s /

ACK.REJ: OFF / BND2s to BND60s /

OTHER MSG: OFF / BND2s to BND60s /

Mic-E: ON / OFF POSITION: ON / OFF WEATHER: ON / OFF OBJECT: ON / OFF ITEM: ON / OFF STATUS: ON / OFF OTHER: ON / OFF MY PACKET: ON / OFF MSG: ON / OFF GRP: ON / OFF BLN: ON / OFF MY MSG: ON / OFF DUP.BCN: ON / OFF DUP.MSG: ON / OFF ACK.REJ: ON / OFF OTHER MSG: ON / OFF TX BCN: ON / OFF TX MSG: ON / OFF

Distance: km / mile Speed: km/h / knot / mph Altitude: m / ft Temp: °C / °F Rain: mm / inch Wind: m/s / mph

250ms / 300ms / 400ms / 500ms / 750ms / 1000ms

Setting Item

(Bold letters: Default)

BNDCNT ALL10s

BND10s

Reference

page

–

Functions Used As Needed

–

101

Page 3

Set Mode

ApplicationforFCC/IC

FCCID:K6620445X20

IC:511B-20445X20

Set mode option No./

setting Item

9-13 BEACON INFO Set the transmission beacon in-

9-14 BEACON

INTERVAL

9-15 BEACON STATS

TXT

9-16 BEACON TX Select automatic or manual send-

9-17 COM PORT

SETTING

9-18 DIGI PATH Select a digital repeater route. P1 OFF

Functions Used As Needed

9-19 GPS DATUM Select a datum used for the GPS

9-20 GPS POWER Turn on/off the GPS function. GPS ON / GPS OFF – 9-21 GPS TIME SET Turn on/off the GPS time and date

9-22 GPS UNIT Select the units for GPS display. Position: .MMM' / 'SS''

9-23 CALLSIGN (APRS) Specify the callsign of your sta-

9-24 MY POSITION Set the position for your station. GPS / Lat N * **°**.**' /

9-25 MY SYMBOL Set the symbol for your station. 45 Icon –

Description of function

formation.

Set a beacon automatic sending interval.

Input setting for status text. S.TXT: ON / OFF

ing of beacon. Set the COM port. STATUS: ON / OFF

function.

automatic acquisition function.

tion.

AMBIGUITY:

SPD / CSE: ON / OFF ALTITUDE: ON / OFF

30sec / 1min / 2min / 3min / 5min / 10min / 15min / 20min / 30min / 60min

TX RATE: 1/1 to 1/8 1 to 5 CH

AUTO / MANUAL / SMART –

SPEED:

INPUT: OFF / GPS OUTPUT: OFF / GPS / WAY.P WAYPOINT:

Mic-E: ON / OFF POSIT: ON / OFF WEATHER: ON / OFF OBJECT: ON / OFF ITEM: ON / OFF

P2 1 WIDE1-1 P3 1 WIDE1-1 / 2 WIDE2-1 P4 1 · · · · · · – · · / 2 · · · · · · – · · P5 1 · · · · · · – · · / 2 · · · · · · – · · P6 1 · · · · · · – · · / 2 · · · · · · – · · P7 1 · · · · · · – · · / 2 · · · · · · – · · P8 1 · · · · · · – · · to 8 · · · · · · – · ·

WGS-84 / Tokyo Mean / Tokyo Japan / Tokyo Korea / Tokyo Okinawa

AUTO / MANUAL –

Speed: km/h / Knot / mph Altitude: m / ft

LON* **°**.**' P1 to P10

Setting Item

(Bold letters: Default)

OFF / 1 dig to 4dig

4800 / 9600 / 19200 / 38400

NMEA9 / NMEA6 / NMEA7 /

NMEA8

– –

Reference

page

–

102

Page 4

Set Mode

ApplicationforFCC/IC

FCCID:K6620445X20

IC:511B-20445X20

Set mode option No./

setting Item

9-26 POSITION

COMMENT

9-27 SmartBeaconing Set the smart beaconing function. STATUS:

9-28 TIME ZONE Set the time zone. UTC ±13.0 H / UTC+0:00 –

* For more details of functions, refer to the APRS Section in the instruction manual.

10 SD CARD 10-1 BACKUP Write or read the information

10-2 MEMORY CH Write or read the memory channel

10-3 GROUP ID Write or read GROUP ID infor-

10-4 FORMAT Format the micro SD memory

11 OPTION 11-1 USB CAMERA Set the USB CAMERA image size

12 CALLSIGN Set the CALLSIGN. – 141

Description of function

Set up the position comment function.

about your transceiver into or from the micro SD memory card.

information into or from the micro SD memory card.

mation into or from the micro SD memory card.

card.

and resolution.

Off Duty / En Route / In Service / Returning / Committed / Special / Priority / Custom 0 to 6 / EMERGENCY!

LOW SPD: 2mph to 30mph HIGH SPD: 31mph to 90mph SLOW RATE: 1min to 100min FAST RATE: 10sec to 180sec TURN ANGL: 5° to 90° TURN SLOP: 1 to 255 TURN TIME: 5sec to 180sec

Write to SD / Read from SD 138

Write to SD / Read from SD 139

Format 24

SIZE: 160×120 / 320×240 QUALITY: LOW / NORMAL /

Setting Item

(Bold letters: Default)

OFF / TYPE1 / TYPE2 / TYPE3

HIGH

Reference

page

140

–

Functions Used As Needed

Displaying the GPS screen.

When using the GPS function, you can display the GPS information on the LCD.

Enter the Set mode:

1 Press and hold M for over 1 second. 2 Turn O to select [1 DISPLAY]. 3 Press H. 4 Turn O to select [1 GPS INFO]. 5 Press H to display the GPS information on the LCD.

103

Page 5

Set Mode

ApplicationforFCC/IC

FCCID:K6620445X20

IC:511B-20445X20

Setting the display method of the remote station information

Set the display method of the remote station information when using the GM Function.

Enter the Set mode:

1 Press and hold M for over 1 second. 2 Turn O to select [1 DISPLAY]. 3 Press H. 4 Turn O to select [2 TARGET LOCATION]. 5 Press H. 6 Turn O to select the display method.

COMPASS: Compass appears.

NUMERIC: Longitude and latitude appear.

7 Press p to set the selected display method, and exit from

the Set mode.

Caution

When the NUMERIC is selected, only the location information of the remote station appears on the LCD. The BACKTRACK function is not activated.

Setting the display method for BACKTRACK

You can set the BACKTRACK screen display method.

Enter the Set mode:

1 Press and hold M for over 1 second. 2 Turn O to select [1 DISPLAY]. 3 Press H.

Functions Used As Needed

4 Turn O to select [3 COMPASS]. 5 Press H. 6 Turn O to select the display method.

HEADING UP: Heading direction is indicated upward.

NORTH UP: North direction is indicated upward.

7 Press p to save the selected display setting and exit the

set mode.

104

Page 6

Set Mode

ApplicationforFCC/IC

FCCID:K6620445X20

IC:511B-20445X20

Setting the search channels for the BAND SCOPE function

You can set the number of channels to be displayed for the band scope when the BAND SCOPE function is used.

Enter the Set mode:

1 Press and hold M for over 1 second. 2 Turn O to select [1 DISPLAY]. 3 Press H. 4 Turn O to select [4 BAND SCOPE]. 5 Press H. 6 Turn O to select the number of channels to search for.

11ch / 19ch / 33ch / 49ch / 101ch

Remark Default: 33ch

7 Press p to set the number of channels to search for, and

exit the Set mode.

Changing the Lighting Condition

You can change the LCD and key lighting condition.

Enter the Set mode:

1 Press and hold M for over 1 second. 2 Turn O to select [1 DISPLAY]. 3 Press H. 4 Turn O to select [5 LAMP].

䎶䎨䎷䎝䎃䎃䎔䎃䎧䎬䎶䎳䎯䎤䎼

䎃䎃䎃䎃䎃䎃䎃䎃䎕䎃䎷䎻䎒䎵䎻

䎃䎃䎃䎃䎃䎃䫹䎃䎖䎃䎰䎨䎰䎲䎵䎼䎃䎃䎃䎃䎃䎃䎃䎃䎗䎃䎶䎬䎪䎱䎤䎯䎬䎱䎪

5 Press H. 6 Turn O to select a lighting condition.

Select a lighting condition with reference to the following

table:

Display Lighting Condition

2 SEC (KEY) to 10 SEC (KEY)

CONTINUOUS The LCD and keys light up continuously.

OFF The LCD and keys do not light.

When O dial or a key is pressed, the LCD and keys light up for the set time.

䎘䎃䎯䎤䎰䎳

䎃䎙䎃䎯䎤䎱䎪䎸䎤䎪䎨䎃䎚䎃䎯䎦䎧䎃䎦䎲䎱䎷䎵䎤䎶䎷䎃䎛䎃䎯䎦䎧䎃䎧䎬䎰䎰䎨䎵

䎃䎘䎃䎯䎤䎰䎳

䎃䎃䎃䎃䎃䎮䎨䎼䎃䎘䎃

䏖䏈䏆

Functions Used As Needed

Remark Default: Key, 5 seconds

7 Press p to save the lighting condition, and exit the Set mode.

105

Page 7

Set Mode

ApplicationforFCC/IC

FCCID:K6620445X20

IC:511B-20445X20

Selecting a Display Language

You can select a display language from Japanese and English.

Enter the Set mode:

1 Press and hold M for over 1 second. 2 Turn O to select [1 DISPLAY]. 3 Press H. 4 Turn O to select [6 LANGUAGE]. 5 Press H. 6 Turn O to select a language.

Select [JAPANESE] or [ENGLISH].

Remark Default: Japanese

7 Press p to save the selected display language, and exit

the Set mode.

Adjusting the LCD Contrast Level

You can adjust the LCD contrast level.

Enter the Set mode:

1 Press and hold M for over 1 second. 2 Turn O to select [1 DISPLAY]. 3 Press H. 4 Turn O to select [7 LCD CONTRAST]. 5 Press H.

Functions Used As Needed

6 Turn O to select a contrast level.

Select from among LEVEL 1 (LIGHT) to LEVEL 15 (DARK).

Remark Default: LEVEL 7

7 Press p to save the selected contrast, and exit the Set

mode.

䎶䎨䎷䎝䎃䎃䎔䎃䎧䎬䎶䎳䎯䎤䎼

䎃䎃䎃䎃䎃䎃䎃䎃䎕䎃䎷䎻䎒䎵䎻䎃䎃䎃䎃䎃䎃䫹䎃䎖䎃䎰䎨䎰䎲䎵䎼䎃䎃䎃䎃䎃䎃䎃䎃䎗䎃䎶䎬䎪䎱䎤䎯䎬䎱䎪

䎙䎃䎯䎤䎱䎪䎸䎤䎪䎨

䎃䎚䎃䎯䎦䎧䎃䎦䎲䎱䎷䎵䎤䎶䎷䎃䎛䎃䎯䎦䎧䎃䎧䎬䎰䎰䎨䎵䎃䎜䎃䎲䎳䎨䎱䎬䎱䎪䎃䎰䎨䎶䎶䎤䎪䎨

䎃䎙䎃䎯䎤䎱䎪䎸䎤䎪䎨

䎃䎃䎃䎃䎃䎨䎱䎪䎯䎬䎶䎫䎃

䎶䎨䎷䎝䎃䎃䎔䎃䎧䎬䎶䎳䎯䎤䎼

䎃䎃䎃䎃䎃䎃䎃䎃䎕䎃䎷䎻䎒䎵䎻䎃䎃䎃䎃䎃䎃䫹䎃䎖䎃䎰䎨䎰䎲䎵䎼䎃䎃䎃䎃䎃䎃䎃䎃䎗䎃䎶䎬䎪䎱䎤䎯䎬䎱䎪

䎚䎃䎯䎦䎧䎃䎦䎲䎱䎷䎵䎤䎶䎷

䎃䎛䎃䎯䎦䎧䎃䎧䎬䎰䎰䎨䎵䎃䎜䎃䎲䎳䎨䎱䎬䎱䎪䎃䎰䎨䎶䎶䎤䎪䎨䎔䎓䎃䎶䎨䎱䎶䎲䎵䎃䎬䎱䎩䎲

䎃䎚䎃䎯䎦䎧䎃䎦䎲䎱䎷䎵䎤䎶䎷

䎃䎃䎃䎃䎃䎯䎨䎹䎨䎯䎃䎚䎃

106

Page 8

Set Mode

ApplicationforFCC/IC

FCCID:K6620445X20

IC:511B-20445X20

Adjusting the LCD Backlight and Keypad Key Light Brightness Level

You can adjust the brightness level of the LCD backlight and keypad key light.

Enter the Set mode:

1 Press and hold M for over 1 second. 2 Turn O to select [1 DISPLAY]. 3 Press H. 4 Turn O to select [8 LCD DIMMER].

䎶䎨䎷䎝䎃䎃䎔䎃䎧䎬䎶䎳䎯䎤䎼

䎃䎃䎃䎃䎃䎃䎃䎃䎕䎃䎷䎻䎒䎵䎻䎃䎃䎃䎃䎃䎃䫹䎃䎖䎃䎰䎨䎰䎲䎵䎼䎃䎃䎃䎃䎃䎃䎃䎃䎗䎃䎶䎬䎪䎱䎤䎯䎬䎱䎪

5 Press H. 6 Turn O to select a brightness level.

You can select from LEVEL 1 (DARK) to LEVEL 6 (BRIGHT).

Remark Default: LEVEL 6

䎛䎃䎯䎦䎧䎃䎧䎬䎰䎰䎨䎵

䎃䎜䎃䎲䎳䎨䎱䎬䎱䎪䎃䎰䎨䎶䎶䎤䎪䎨䎔䎓䎃䎶䎨䎱䎶䎲䎵䎃䎬䎱䎩䎲䎔䎔䎃䎃䎶䙵䎰䎨䎷䎨䎵䎃䎶䎼䎰䎥䎲䎯

7 Press p to save the selected display brightness level, and

exit the Set mode.

䎃䎛䎃䎯䎦䎧䎃䎧䎬䎰䎰䎨䎵

䎃䎃䎃䎃䎃䎃䎯䎨䎹䎨䎯䎃䎙䎃

Changing the Opening Message Displayed Immediately after Power-on

You can select the message displayed under the “YAESU” logo from among four types: “no message”, “power supply voltage”, “message comprising up to 16 characters”, and “callsign”.

Enter the Set mode:

1 Press and hold M for over 1 second. 2 Turn O to select [1 DISPLAY]. 3 Press H. 4 Turn O to select [9 OPENING MESSAGE]. 5 Press H.

Functions Used As Needed

107

Page 9

Set Mode

ApplicationforFCC/IC

FCCID:K6620445X20

IC:511B-20445X20

6 Turn O to select the display method.

Select a message type with reference to the following table:

Remark Default: CALLSIGN

Display Display Condition

NORMAL The YAESU logo appears immediately after power-on.

OFF Immediately after power-on, the reception frequency, etc. appear without display-

DC The power supply voltage and time appear immediately after power-on.

MESSAGE A message comprising up to 16 characters ap-

CALLSIGN Your callsign appears immediately after power-on.

ing an opening message.

pears immediately after power-on. Pressing H displays the message registration screen. Enter a message to be displayed following the procedure described in “Assigning a Name to a Memory Channel” (See page 47).

7 Press p to save the selected display method, and exit from the Set mode.

Measuring the Battery Voltage and the Transceiver Temperature Power Supply Voltage Measurement Function/Temperature Measurement Function

You can measure the battery voltage and the temperature inside the transceiver. When the optional external power supply adapter with a cigarette plug (SDD-13) is connected, the power supply voltage of this adapter is measured.

Enter the Set mode:

1 Press and hold M for over 1 second. 2 Turn O to select [1 DISPLAY].

Functions Used As Needed

3 Press H. 4 Turn O to select [10 SENSOR INFO].

䎶䎨䎷䎝䎃䎃䎔䎃䎧䎬䎶䎳䎯䎤䎼

䎃䎃䎃䎃䎃䎃䎃䎃䎕䎃䎷䎻䎒䎵䎻䎃䎃䎃䎃䎃䎃䫹䎃䎖䎃䎰䎨䎰䎲䎵䎼

䎃䎃䎃䎃䎃䎃䎃䎃䎗䎃䎶䎬䎪䎱䎤䎯䎬䎱䎪

5 Press H.

The voltage and temperature appear on the LCD.

Remark When the temperature appears on the LCD, pressing V

toggles the unit of temperature display between °C and °F.

7 Press M. 8 Press p to exit from the Set mode.

䎔䎓䎃䎶䎨䎱䎶䎲䎵䎃䎬䎱䎩䎲

䎔䎔䎃䎃䎶䙵䎰䎨䎷䎨䎵䎃䎶䎼䎰䎥䎲䎯䎃䎔䎃䎪䎳䎶䎃䎬䎱䎩䎲䎃䎕䎃䎷䎤䎵䎪䎨䎷䎃䎯䎲䎦䎤䎷䎬䎲䎱

䎔䎓䎃䎶䎨䎱䎶䎲䎵䎃䎬䎱䎩䎲

108

䎃䎃䎃䎃䎹䎲䎯䎷䫹䎝䎃䎃䎃䎃䎯䏌䏗䎃䎃䎚䎑䎗䎹䎃䎃䎃䎃䎃䎷䎨䎰䎳䫹䎝䎃䎃䎃䎃䎃䎃䎚䎚䫹 q䎩

䎃

Page 10

Set Mode

///

ApplicationforFCC/IC

FCCID:K6620445X20

IC:511B-20445X20

Tips

• The display changes as follows depending on the type of the power supply used. Battery pack: “Lit” Battery case: “Dry” External power supply adapter: “Ext”

• During mono band reception, the voltage can be displayed on the LCD constantly (See page 27).

• This function displays the temperature inside the transceiver.

• In a situation where the temperature inside of the transceiver does not rise (e.g., standby reception), you can know the approximate outside temperature from the temperature displayed on the LCD.

Changing the Display Pattern of the PO Meter

You can select a display pattern of the S/PO meter from among four types.

Enter the Set mode:

1 Press and hold M for over 1 second. 2 Turn O to select [1 DISPLAY]. 3 Press H. 4 Turn O to select [11 S-METER SYMBOL]. 5 Press H. 6 Turn O to select a display pattern.

Remark Default:

7 Press p to save the selected display pattern, and exit from

the Set mode.

Switching between AM Antennas

You can switch antennas when listening to AM broadcast stations. For details, see “Switching between AM Antennas” on page 33.

Reducing receiver sensitivity Attenuator (ATT) Function

If the signal from the remote station is too strong or, a strong signal is present nearby that interferes with reception, use the attenuator (ATT) function.

Enter the Set mode:

1 Press and hold M for over 1 second. 2 Turn O to select [2 TX/RX]. 3 Press H.

Functions Used As Needed

109

Page 11

Set Mode

ApplicationforFCC/IC

FCCID:K6620445X20

IC:511B-20445X20

4 Turn O to select [1 MODE]. 5 Press H. 6 Turn O to select [2 ANTENNA ATT]. 7 Press H. 8 Turn O to select [ON].

Remark Default: OFF

9 Press p to save the attenuator function setting, and exit

the Set mode.

Tip

• The amount of attenuation by the attenuator (ATT) is about 10 dB.

Setting the transmission modulation level

You can set the transmission modulation level to half of its usual level. Set [OFF] for normal amateur operation.

Enter the Set mode:

1 Press and hold M for over 1 second. 2 Turn O to select [2 TX/RX]. 3 Press H. 4 Turn O to select [1 MODE]. 5 Press H. 6 Turn O to select [3 HALF DEVIATION]. 7 Press H.

Functions Used As Needed

8 Turn O to select [ON]

Remark Default: OFF

9 Press p to save the transmission modulation level is set,

and exit the Set mode.

110

Page 12

Set Mode

ApplicationforFCC/IC

FCCID:K6620445X20

IC:511B-20445X20

Changing the mode manually

Manually switch to an optimum mode (radio wave type) according to the frequency band. For more details, see “Changing the Mode Manually” on page 38.

Switching between digital and analog mode

You can set digital and analog mode switching and digital transmission mode.

Enter the Set mode:

1 Press and hold M for over 1 second. 2 Turn O to select [2 TX/RX]. 3 Press H. 4 Turn O to select [2 DIGITAL]. 5 Press H. 6 Turn O to select [1 DIGITAL MODE]. 7 Press H. 8 Turn O to select [MODE]. 9 Press H. 10

Turn O to select your desired mode.

DIGITAL: Transmit and receive in the digital mode.

ANALOG: Transmit and receive in the analog mode.

AMS (Automatic Mode Select):

Tune to the transmission and reception mode of the remote

station from which a signal is automatically received.

11 Press M. 12

Turn O to select [DIGI TX].

Press H.

Turn O to select a reception mode.

DN: Usual digital communication mode. Conversation is

infrequently interrupted even under low power level.

VW: (Voice Wide) Full rate high quality sound mode This is the transmission function

to prioritize the sound quality when the communication condition of the remote station is relatively good.

Press p to save the setting and exit the Set mode.

Functions Used As Needed

111

Page 13

Set Mode

ApplicationforFCC/IC

FCCID:K6620445X20

IC:511B-20445X20

Setting the AMS transmission mode

When operating in the AMS function, the transmit mode may be selected:

1 Press and hold M for over 1 second. 2 Turn O to select [2 TX/RX]. 3 Press H. 4 Turn O to select [2 DIGITAL]. 5 Press H. 6 Turn O to select [1 DIGITAL MODE]. 7 Press H. 8 Turn O to select [AMS MODE]. 9 Press H. 10

Turn O to select the AMS transmit mode.

TX M: The operating mode is automatically selected

from four communication modes to match the received signal. Pressing the Microphone [PTT] momentarily, toggles between the Digital and Analog communication modes.

TX FM: The RX mode is automatically selected from the

four communication modes to match the received signal. The TX mode is automatically changed to the “FM” mode.

TX DN: The RX mode is automatically selected from the

four communication modes to match the received signal. The TX mode is automatically changed to the “DN” mode.

TX VW: The RX mode is automatically selected from the four communication modes

Functions Used As Needed

AUTO: The RX and TX operating mode is automatically selected from the four

Remarks • Default: TX M

• Blink “

Press p to save the setting and exit the Set mode.

to match the received signal. The TX mode is automatically changed to the “VW” mode.

communication modes to match the received signal.

▎” : TX M

▎

Blink “

OO” : TX FM / TX DN / TX VW

The OO symbol display differs according to the received signal.

112

Page 14

Setting the squelch type for the digital mode

ApplicationforFCC/IC

FCCID:K6620445X20

IC:511B-20445X20

You can set the squelch type for the digital mode.

Enter the Set mode:

1 Press and hold M for over 1 second. 2 Turn O to select [2 TX/RX]. 3 Press H. 4 Turn O to select [2 DIGITAL]. 5 Press H. 6 Turn O to select [2 SQL TYPE]. 7 Press H. 8 Turn O to select [SQL TYPE]. 9 Press H. 10

Turn O to select a squelch type.

OFF: Voice is always output upon receiving a digital signal

from a Yaesu transceiver.

CODE: Voice is output only when receiving a signal with a

corresponding SQL CODE.

BREAK: Voice is output regardless of any squelch code

when the remote station transmits with BREAK set.

11 Press M. 12

Turn O to select [SQL CODE].

Press H.

Turn O to enter a code.

You can enter SQL CODE of 126 types from 001 to 126.

Press p to save the SQL CODE setting and exit the Set mode.

Set Mode

Setting the pop up time of the remote station information

You can set the time duration to display the remote station information, such as callsign, on the LCD.

Enter the Set mode:

1 Press and hold M for over 1 second. 2 Turn O to select [2 TX/RX]. 3 Press H. 4 Turn O to select [2 DIGITAL]. 5 Press H.

Functions Used As Needed

113

Page 15

Set Mode

ApplicationforFCC/IC

FCCID:K6620445X20

IC:511B-20445X20

6 Turn O to select [3 DIGI POPUP]. 7 Press H. 8 Turn O to select the display method.

OFF: Does not display the remote station information.

BND2s to 60s: Set the time to display the remote station

information (2 to 60 seconds).

BNDCNT: Always display the remote station information.

Remark Default: 10 seconds

9 Press p to save the pop up time setting and exit the Set mode.

Setting the Standby Beep

When communicating in a digital mode, a beep is sounded after the end of the other stations transmission.

1 Press and hold M for over 1 second. 2 Turn O to select [2 TX/RX]. 3 Press H. 4 Turn O to select [2 DIGITAL]. 5 Press H. 6 Turn O to select [5 STANDBY BEEP]. 7 Press H. 8 Turn O to select [OFF]/[ON].

OFF: Disable the STANDBY BEEP feature.

ON: Enable the STANDBY BEEP feature.

Remark Default: ON

9 Press p to exit from the Set mode.

Functions Used As Needed

114

Page 16

Displaying the version of the DSP program

䎶䎨䎷䎝䎃䎃䎕䎃䎷䎻䎒䎵䎻

䎃䎃䎃䎃䎃䎃䎃䎃䎖䎃䎰䎨䎰䎲䎵䎼䎃䎃䎃䎃䎃䎃䎃䎃䎗䎃䎶䎬䎪䎱䎤䎯䎬䎱䎪䎃䎃䎃䎃䎃䎃䎃䎃䎘䎃䎶䎦䎤䎱

ApplicationforFCC/IC

FCCID:K6620445X20

IC:511B-20445X20

You can check the DSP program version of the built in digital unit of the transceiver.

First enter the digital mode, and then enter the Set mode:

1 Press and hold M for over 1 second. 2 Turn O to select [2 TX/RX]. 3 Press H. 4 Turn O to select [2 DIGITAL]. 5 Press H. 6 Turn O to select [6 DSP Ver]. 7 Press H.

The version of the DSP program appears on the LCD.

8 Press p to exit from the Set mode.

Adjusting the microphone sensitivity Microphone Gain

You can adjust the input level of the built-in microphone or an optional external microphone.

Enter the Set mode:

1 Press and hold M for over 1 second. 2 Turn O to select [2 TX/RX]. 3 Press H. 4 Turn O to select [3 AUDIO]. 5 Press H. 6 Turn O to select [1 MIC GAIN].

䎖䎃䎤䎸䎧䎬䎲

䎔䎃䎰䎲䎧䎨

䎃䎕䎃䎧䎬䎪䎬䎷䎤䎯

7 Press H. 8 Turn O to select a microphone sensitivity level.

Select a microphone gain level from the following:

LEVEL 1 (Lowest sensitivity) to LEVEL 9 (Highest sensitivity)

Remark Default: LEVEL 5

䎔䎃䎰䎬䎦䎃䎃䎪䎤䎬䎱

䎕䎃䎰䎸䎷䎨䎃䎖䎃䎵䎻䎃䎤䎩䎃䎧䎸䎤䎯䎃䎗䎃䎃䎹䎲䎯䎃䎰䎲䎧䎨

9 Press M twice.

The selected microphone gain level is set.

䎃䎔䎃䎰䎬䎦䎃䎪䎤䎬䎱

䎃䎃䎃䎃䎃䎃䎯䎨䎹䎨䎯䎃䎘

Set Mode

Functions Used As Needed

115

Page 17

Set Mode

ApplicationforFCC/IC

FCCID:K6620445X20

IC:511B-20445X20

Press p to exit the Set mode.

Tips

• Increasing the microphone gain excessively can distort the sound or pick up the surrounding noise, impairing intelligibility.

• Be sure to adjust the microphone gain whenever you change microphones.

Muting Voice

In the dual reception mode, the audio being received on the non-operating band is muted when a signal is herd on the operating band. For more details, see “Muting Audio” on page 35.

Simultaneously radio broadcast reception

Set the mute time of the simultaneous broadcast reception. For more details, see “AF-DUAL Function” for simultaneously monitoring the amateur frequency while listening to the broadcast radio.

Changing the sound volume setting method

You can set the sound volume adjustment mode to be automatically canceled after about 3 seconds, after pressing v and then adjusting the sound volume with O.

Enter the Set mode:

1 Press and hold M for over 1 second. 2 Turn O to select [2 TX/RX]. 3 Press H. 4 Turn O to select [3 AUDIO]. 5 Press H. 6 Turn O to select [4 VOL MODE].

Functions Used As Needed

7 Press H. 8 Turn O to select [AUTO BACK].

Remark Default: NORMAL Tip Usually adjust the sound volume by turning O while pressing

v. If the [AUTO BACK] is selected, the sound volume adjustment mode will be automatically canceled after you have pressed v to enter the sound volume adjustment mode and

return to the frequency display screen.

9 Press p to exit the Set mode.

116

Page 18

Set Mode

ApplicationforFCC/IC

FCCID:K6620445X20

IC:511B-20445X20

Setting memory bank link

You can link multiple registered memory banks, and also recall a frequently used memory bank immediately

Enter the Set mode:

1 Press and hold M for over 1 second. 2 Turn O to select [3 MEMORY]. 3 Press H. 4 Turn O to select [1 BANK LINK]. 5 Press H. 6 Turn O to select a memory bank to link. 7 Press B.

The cursor moves to the position (such as BANK1) to set

link.

8 Turn O to select [ON].

Remark Default: OFF

9 Press B. 10

Also set link to other memory banks.

Set link to each memory bank from memory bank 1 through

memory bank 24 by repeating step 6 to 9.

11 Press H.

The memory bank link is set.

Press p.

Exits from the Set mode.

Assigning a name to a memory bank

A memory bank can be assigned a name with up to 16 characters. For more details, see “Assigning Name to Memory Bank” on page 49.

Assigning a name to a memory channel

Memory channels and home channels may be assigned a name (memory tag) such as a callsign or broadcast station name. For more details, see “Using Memory Tag” on page 46.

Functions Used As Needed

117

Page 19

Set Mode

ApplicationforFCC/IC

FCCID:K6620445X20

IC:511B-20445X20

Prohibiting registration to memory channel Memory Channel Protect Function

A memory channel may be protected so that a new frequency or memory channel tag name cannot be registered to it.

Enter the Set mode:

1 Press and hold M for over 1 second. 2 Turn O to select [3 MEMORY]. 3 Press H. 4 Turn O to select [4 MEMORY PROTECT]. 5 Press H. 6 Turn O to select [ON].

Any registration to the memory channel is prohibited.

Remark Default: OFF

7 Press p to save the memory channel protect, and exit the

Set mode.

Setting memory skip function

Set the scan method for scanning memory channels. For more details, see “Specifying a Skip/Selected Memory Channel” on page 60.

Registering to a memory channel with the lowest memory channel number Memory Channel Write Function

When registering to a memory channel. you can display an unregistered memory channel with the lowest memory channel number.

Enter the Set mode:

Functions Used As Needed

1 Press and hold M for over 1 second. 2 Turn O to select [3 MEMORY]. 3 Press H. 4 Turn O to select [6 MEMORY WRITE]. 5 Press H. 6 Turn O to select [LOWER].

A memory channel with the lowest memory channel number

appears on the LCD.

Remark Default: NEXT

7 Press p to set the memory channel registration to the

lowest unregistered memory channel number, and exit from the Set mode.

118

Page 20

Notifying a call from a remote station by the bell

䎶䎨䎷䎝䎃䎃䎗䎃䎶䎬䎪䎱䎤䎯䎬䎱䎪

䎃䎃䎃䎃䎃䎃䎃䎃䎘䎃䎶䎦䎤䎱䎃䎃䎃䎃䎃䎃䫹䎙䎃䎪䎰䎃䎃䎃䎃䎃䎃䎃䎃䎚䎃䎺䎬䎵䎨䎶䙵䎻

ApplicationforFCC/IC

FCCID:K6620445X20

IC:511B-20445X20

Notifies you of a call from a remote station by the bell. See “Notification of a Call from a Remote Station by the Bell” on page 89.

Selecting a DCS code

Select the DCS code from 104 codes from 023 to 754. For more details, see “Setting a DCS Code” on page 86.

Transmit and receive a DCS Code with a inverted phase DCS INVERSION Function

You can transmit and receive a DCS code with an inverted phase when using the digital code squelch function.

Enter the Set mode:

1 Press and hold M for over 1 second. 2 Turn O to select [4 SIGNALING]. 3 Press H. 4 Turn O to select [3 DCS INVERSION].

䎶䎨䎷䎝䎃䎃䎗䎃䎶䎬䎪䎱䎤䎯䎬䎱䎪

䎃䎃䎃䎃䎃䎃䎃䎃䎘䎃䎶䎦䎤䎱䎃䎃䎃䎃䎃䎃䫹䎙䎃䎪䎰䎃䎃䎃䎃䎃䎃䎃䎃䎚䎃䎺䎬䎵䎨䎶䙵䎻

5 Press H. 6 Turn O to select a phase.

When a phase is selected for the reception side, the phase

for transmission side is automatically determined.

Reception: [Homeomorphic], [Both Phase],

[Inverted Phase], [Homeomorphic], [Both Phase], [Inverted Phase]

Transmission: [Homeomorphic], [Inverted Phase],

[Inverted Phase], [Inverted Phase], [Homeomorphic], [Homeomorphic]

Remark Default: Reception [Homeomorphic], Transmission [Homeomorphic]

䎖䎃䎃䎧䎦䎶䎃䎃䎬䎱䎹䎨䎵䎶䎬䎲䎱

䎗䎃䎃䎧䎷䎰䎩䎃䎃䎰䎲䎧䎨䎘䫹䎧䎷䎰䎩䎃䎃䎶䎨䎯䎨䎦䎷

䎙䫹䎳䎤䎪䎨䎵

䎃䎖䎃䎧䎦䎶䎃䎃䎬䎱䎹䎨䎵䎶䎬䎲䎱

䎃䎃䎃䎃䎃䎃䎵䎻䙵䎱䎲䎵䎰䎤䎯䎃䎃䎃䎃䎃䎃䎃䎷䎻䙵䎱䎲䎵䎰䎤䎯

7 Press p.

The phase of DCS code is set, and exits from the Set mode.

Set Mode

Functions Used As Needed

119

Page 21

Set Mode

ApplicationforFCC/IC

FCCID:K6620445X20

IC:511B-20445X20

Setting the transmission method of the DTMF code

Set the transmission method of the registered DTMF code. For more details, see “Sending the Registered DTMF Code” on page 80.

Setting DTMF code

The maximum of 16 digit DTMF code can be registered for a telephone number to make a call through the public telephone line from a phone patch. For more details, see “Using DTMF Function” on page 79.

Calling only a specific station New Pager Function

When using transceivers with your friends, specifying personal codes allows only a specific station to be called. For more details, see “Calling Only a Specific Station New Pager Function” on page 90.

Enabling no-communication squelch function PR FREQUENCY Function

You can set a no-communication squelch frequency in steps of 100 Hz within the range from 300 Hz to 3000 Hz.

Enter the Set mode:

1 Press and hold M for over 1 second. 2 Turn O to select [4 SIGNALING]. 3 Press H. 4 Turn O to select [7 PR FREQUENCY]. 5 Press H. 6 Turn O to tune in to a frequency.

Functions Used As Needed

Select no-communication squelch frequency in steps of 100

Hz.

Remark Default: 1600 Hz

7 Press p to set the no-communication squelch function,

and exit the Set mode.

120

Page 22

Set Mode

ApplicationforFCC/IC

FCCID:K6620445X20

IC:511B-20445X20

Adjusting the squelch level SQL LEVEL Function

You can set squelch level to mute the raspy noise heard.

Enter the Set mode:

1 Press and hold M for over 1 second. 2 Turn O to select [4 SIGNALING]. 3 Press H. 4 Turn O to select [8 SQL LEVEL].

䎶䎨䎷䎝䎃䎃䎗䎃䎶䎬䎪䎱䎤䎯䎬䎱䎪

䎃䎃䎃䎃䎃䎃䎃䎃䎘䎃䎶䎦䎤䎱䎃䎃䎃䎃䎃䎃䫹䎙䎃䎪䎰䎃䎃䎃䎃䎃䎃䎃䎃䎚䎃䎺䎬䎵䎨䎶䙵䎻

5 Press H. 6 Turn O to select a squelch level.

Select from among LEVEL 0 to LEVEL 15.

The higher the squelch level, the greater the noise reduction.

Remark Default: LEVEL 1

7 Press p to save the selected squelch type, and exit the Set

mode.

䎛䎃䎶䎴䎯䎃䎃䎯䎨䎹䎨䎯

䎜䎃䎶䎴䎯䎃䎶䙵䎰䎨䎷䎨䎵䎔䎓䎃䎶䎴䎯䎃䎃䎨䎻䎳䎤䎱䎷䎬䎲䎱䎔䎔䎃䎶䎴䎯䎃䎃䎷䎼䎳䎨

䎃䎛䎃䎶䎴䎯䎃䎃䎯䎨䎹䎨䎯

䎃䎃䎃䎃䎯䎨䎹䎨䎯䎃䎔䎃

Setting the signal strength to output sound S Meter Squelch Function

You can set A-Band and B-Band individually to output the sound only when receiving a signal stronger than signal strength level set to the S-Meter Level.

1 Select a band as an operating band. 2 Press and hold M for over 1 second to enter the Set

mode.

3 Turn O to select [4 SIGNALING]. 4 Press H. 5 Turn O to select [9 SQL S-METER]. 6 Press H. 7 Turn O to select a setting value.

Select a S-Meter level with reference to the table shown

below.

Remark Default: OFF

8 Press p to save the selected S-Meter level, and exit the

Set mode.

Functions Used As Needed

121

Page 23

Set Mode

ApplicationforFCC/IC

FCCID:K6620445X20

IC:511B-20445X20

Display S-Meter Display Operating Status

OFF No display

S-Meter squelch function is OFF. (By default, S-Meter squelch function is set to OFF.)

Level 1

Level 2

Level 3

Level 4

Level 5

Level 6

Level 7

Level 8

Level 9

Outputs the sound of signal stronger than the S-Meter level 1.

Outputs the sound of signal stronger than the S-Meter level 2.

Outputs the sound of signal stronger than the S-Meter level 3.

Outputs the sound of signal stronger than the S-Meter level 4.

Outputs the sound of signal stronger than the S-Meter level 5.

Outputs the sound of signal stronger than the S-Meter level 6.

Outputs the sound of signal stronger than the S-Meter level 7.

Outputs the sound of signal stronger than the S-Meter level 8.

Outputs the sound of signal stronger than the S-Meter level 9.

Setting the squelch type for transmission and reception SQL EXPANTION FUNCTION

Squelch types set beforehand can function separately for transmission and reception.

Enter the Set mode:

Functions Used As Needed

1 Press and hold M for over 1 second. 2 Turn O to select [4 SIGNALING]. 3 Press H. 4 Turn O to select [10 SQL EXPANTION]. 5 Press H. 6 Turn O to select [ON].

ON: Use separate squelch for transmission and reception.

OFF: Use the same squelch for transmission and reception.

Remark Default: OFF

7 Press p to save the separate squelch setting, and exit the

Set mode.

122

Page 24

Setting the type of tone squelch

䎶䎨䎷䎝䎃䎃䎗䎃䎶䎬䎪䎱䎤䎯䎬䎱䎪

䎃䎃䎃䎃䎃䎃䎃䎃䎘䎃䎶䎦䎤䎱䎃䎃䎃䎃䎃䎃䫹䎙䎃䎪䎰䎃䎃䎃䎃䎃䎃䎃䎃䎚䎃䎺䎬䎵䎨䎶䙵䎻

ApplicationforFCC/IC

FCCID:K6620445X20

IC:511B-20445X20

Set the tone squelch to open the squelch only when a signal containing the specified frequency tone is received. For more details, see “Using the Tone Squelch Function” on page 84.

Selecting a tone frequency

Select the tone frequency from 50 types between 67.0 MHz and 254.1 MHz. For more details, see “Setting a Tone Frequency” on page 85.

Setting the sound and speed during tone search Tone Search Function

Sound can be muted during tone search. The operation speed of the tone search can also be changed.

Enter the Set mode:

1 Press and hold M for over 1 second. 2 Turn O to select [4 SIGNALING]. 3 Press H. 4 Turn O to select [13 TONE-SRCH].

䎶䎨䎷䎝䎃䎃䎗䎃䎶䎬䎪䎱䎤䎯䎬䎱䎪

䎃䎃䎃䎃䎃䎃䎃䎃䎘䎃䎶䎦䎤䎱䎃䎃䎃䎃䎃䎃䫹䎙䎃䎪䎰䎃䎃䎃䎃䎃䎃䎃䎃䎚䎃䎺䎬䎵䎨䎶䙵䎻

5 Press H twice. 6 Turn O to select MUTE to [ON].

Remark Default: ON

7 Press M.

䎔䎖䎃䎷䎲䎱䎨䙵䎶䎵䎦䎫

䎃䎔䎃䎃䎥䎨䎯䎯䎃䎕䎃䎃䎧䎦䎶䎃䎃䎦䎲䎧䎨䎃䎖䫹䎧䎦䎶䎃䎃䎬䎱䎹䎨䎵䎶䎬䎲䎱

8 Turn O to select [SPPED]. 9 Press H. 10

Turn O to select SPEED to [Rapid].

Remark Default: FAST

Press p to save the Tone Search setting and exit the Set mode.

䎔䎖䎃䎷䎲䎱䎨䙵䎶䎵䎦䎫䎃䎃䎃䎰䎸䎷䎨䎃䎃䎃䎝䎃䎃䎲䎱䎃䎃䎃䎶䎳䎨䎨䎧䎃䎃䎃䎝䎃䎃䎩䎤䎶䎷

Set Mode

Functions Used As Needed

123

Page 25

Set Mode

䎶䎨䎷䎝䎃䎃䎘䎃䎶䎦䎤䎱

䎃䎃䎃䎃䎃䎃䎃䎃䎙䎃䎪䎰䎃䎃䎃䎃䎃䎃䫹䎚䎃䎺䎬䎵䎨䎶䙵䎻

䎃䎃䎃䎃䎃䎃䎃䎃䎛䎃䎦䎲䎱䎩䎬䎪

ApplicationforFCC/IC

FCCID:K6620445X20

IC:511B-20445X20

ON/OFF for the Weather Alert Feature

Setting the Weather Alert Feature, used for notifying storms and hurricanes, ON or OFF.

Enter the Set mode:

1 Press and hold M for over 1 second. 2 Turn O to select [4 SIGNALING]. 3 Press H. 4 Turn O to select [14 WX ALERT]. 5 Press H. 6 Turn O to select [ON].

ON: Enables the Weather Alert Feature.

OFF: Disables the Weather Alert Feature.

Remark Default: OFF

7 Press p to save the Weather Alert ON or OFF setting, and exit the Set mode

Setting the surveillance interval time for priority channels DW TIME Function

When the dual reception function is active, the interval for monitoring the signal of the priority channel can be set.

Enter the Set mode:

1 Press and hold M for over 1 second. 2 Turn O to select [5 SCAN]. 3 Press H. 4 Turn O to select [1 DW TIME].

䎶䎨䎷䎝䎃䎃䎘䎃䎶䎦䎤䎱

䎃䎃䎃䎃䎃䎃䎃䎃䎙䎃䎪䎰䎃䎃䎃䎃䎃䎃䫹䎚䎃䎺䎬䎵䎨䎶䙵䎻

䎃䎃䎃䎃䎃䎃䎃䎃䎛䎃䎦䎲䎱䎩䎬䎪

5 Press H. 6 Turn O to select the monitoring interval.

Interval can be selected from 0.1 SEC to 10 SEC.

Functions Used As Needed

Remark Default: 5 seconds

䎔䎃䎧䎺䎃䎃䎷䎬䎰䎨

䎕䎃䎶䎦䎤䎱䎃䎃䎯䎤䎰䎳

䎃䎖䎃䎶䎦䎤䎱䎃䎃䎵䎨䙵䎶䎷䎤䎵䎷

䎃䎗䎃䎶䎦䎤䎱䎃䎃䎵䎨䎶䎸䎰䎨

7 Press p to save the priority memory channel monitoring

interval setting and exit the Set mode.

䎔䎃䎧䎺䎃䎃䎷䎬䎰䎨

䎃䎃䎃䎃䎃䎘䎑䎓䎃

䏖䏈䏆

124