with 5” Dash Monitor
BT54860/BT54998
TABLE OF CONTENTS
1. Introduction ...............................................................................................................................................................................1
2. Package Contents ...................................................................................................................................................................2
3. Product Specications .......................................................................................................................................................... 3
4. Installation Guide ....................................................................................................................................................................3
5. Settings and Operation ........................................................................................................................................................ 9
6. Safety Information ................................................................................................................................................................12
7. Maintenance & Warranty ....................................................................................................................................................14
8. General Information ............................................................................................................................................................19
1
Please read all of the installation instructions carefully before installing the product. Improper
installation will void manufacturer’s warranty. The installation instructions do not apply to all types
of vehicles, and are written as guidelines to assist in installing the system.
Consult an experienced technician if you are not comfortable installing the product. You can also
contact Winplus at 866.294.9244 to speak to one of our installation specialists if you have any
specic questions regarding the Backup Camera.
BEFORE using the Backup Camera, please read the safety information provided in this user
manual. ALWAYS use the product as outlined in this user manual.
Please make sure to read and understand all local laws and regulations regarding cameras and their
use in a vehicle. Laws vary by state.
1. INTRODUCTION
2
1. 5” Dash Monitor
2. 1 Backup Camera
3. 12V/24V Power Adapter for Monitor
4. Hardwire Cable for Monitor
5. Suction Cup Mount for Monitor
6. Install Kit
7. Optional 12V/24V Power Adapter for
the Camera
8. User’s Manual
9. Quick Install Guide
10. Professional Installation Oer
(For US only)
2. PACKAGE CONTENTS
7.
8.
9.
10.
6. 1.
2.
3.
4.
5.
3
1. Frequency: 2.4GHz
2. Operating Voltage: DC 12V / 24V
3. Operating Temperature: -10~+50°C
4. Maximum Signal Range: 30 feet/10Metres
(without Interference or Obstruction)
5. Camera Water Resistance: IP67 rating
DASH MONITOR INSTALLATION
1. Stick the Suction Cup Mount on the windshield and adjust to your desired position.
2. Hook the Dash Monitor on to the windshield mount.
3. Remove the Yada Dash Monitor protective overlay.
4. Now power the monitor:
a. 12V/24V Power Adapter
Take the 12V/24V Power Adapter and plug adapter into the right side of the Yada Dash
Monitor. Plug the other end into 12V/24V power port in your car.
b. Hard wire
Take the Hard Wire Power Adapter and plug adapter into the right side of the Yada Dash
Monitor. Run cable to fuse box and connect to fused accessory power source. Refer to
your vehicle owner manual for location of available accessory fuses.
5. At this time, the Yada Dash Monitor is ready to be automatically powered on when the vehicle
engine starts.
Warning: Many vehicles provide constant power to the 12V outlet. If your outlet provides constant
power, please remember to unplug the monitor when not in use to avoid draining the vehicle
battery.
3. PRODUCT SPECIFICATIONS
4. INSTALLATION GUIDE
4
BACKUP CAMERA INSTALLATION - Hardwire Power
This installation is based on powering the Camera over the reverse tail lights. When installed as
directed, the camera image will only appear when the vehicle is in reverse.
Caution: This unit is designed to operate on a 12V/24V DC NEGATIVE GROUND electrical system.
Connecting to other types of electrical systems will cause damage to your vehicle. Please contact
the manufacturer if you are unaware of the system type in your vehicle.
1. Remove your license plate
2. Determine the best route for the Camera Cable from the top of your license plate to the inside
of the vehicle. You may need to drill a small hole in the panel behind where the license plate is
situated.
3. Take the Camera and run the cable through the Rubber Ring Grommet, then from the outside of
your car to the inside. Pull the cable through so that there is a small amount of slack and you can
still move the Camera around the license plate.
4. Locate the reverse taillights wiring behind your reverse light. You may need to remove the
interior panel in order to locate. You only need to attach the Camera to ONE of the reverse
lights, not both. If you cannot manually locate the taillight cables, please contact the vehicle
manufacturer or reference a wiring diagram for your vehicle.
Hardwire cable for Camera
Camera cable
Reverse Light Power Wires
5
5. At your taillight, remove the light bulb socket from the reverse light housing.
6. Determine the reverse light power wires for your car, designating the positive and negative
wires. If you are not sure of which are the power wires, then please contact your vehicle
manufacturer or reference a wiring diagram for your vehicle.
7. Connecting the Camera Power Cable:
a. Take the open wire end of this cable, and connect it to the power wires of your car (as
determined in step 4). Using the Snap Lock Splice Connectors, connect the Camera’s
Red wire to reverse light’s Positive wire. Connect the Camera’s Black Wire to reverse
light’s Negative wire.
b. Use pliers to squeeze the metal tabs of the Snap Lock Splice Connectors and ensure a
solid connection, then snap the plastic cover closed.
8. While sitting in the driver’s seat of the car with the key in the accessory position. The monitor
will automatically start when connected to a power source. If when you place the vehicle in
reverse there is no image, go to the section “Settings and Operation” for more information.
9. Put the vehicle in reverse. If you have a clear picture, put the vehicle back in park and turn the
key to the o position. You are now ready for nal steps.
10. Use the provided Zip ties to secure wires neatly within your car.
11. Replace the light socket back into the reverse light housing.
12. Replace any interior panels that may have been removed to access the taillight and close your
trunk or rear hatch.
13. Standing with the license plate in one hand and the Camera in the other hand, slide the Camera
along the top of the license plate in order to determine the placement. Best placement is in the
center of the license plate. If you have a rear hatch handle you may need to remove the Camera
bracket, turn the bracket upside down and reattach to the Camera. You would then mount the
Camera from the bottom of the license plate.
14. Peel o the lining of the double-sided tape already attached to the Camera and press rmly to
the license plate to secure the Camera. Make sure the back of the license plate is clean before
attaching double-sided tape.
15. Press the license plate and the Camera mounting rmly to the car to secure and get full contact
between the license plate and the double-sided tape. Screw the license plate back onto the rear
of your vehicle.
6
16. Once license plate and Camera are secure, you can adjust the vertical angle of the Camera to your
specic need.
17. As a last check, note the position of the view from the Camera when you place the vehicle in reverse.
Adjust the angle of the Camera as necessary to achieve the best rear view.
WARNING:
Do not attach the 12/24V Direct Power Adapter to the Hardwire Adapter at any time. Only one power
option can be used with the Camera.
DIESEL INSTRUCTION:
Temporarily connect the Camera following the wiring instructions above. Then check the Camera image
for rolling lines with vehicle running. If there are no rolling lines, permanently install the components
and wiring. If rolling lines occur you will need to run a power wire directly to the battery post instead of
using the reverse lights. Then the power line will need to be cut and run to a switch near the driver so the
Camera can be switched on/o. Without a switch the Camera would drain the battery and possibly burn
out the Camera. Be sure to use a fuse when connecting to the battery post.
12V/24V Power
Adapter for Camera
Hardwire cable
for Camera
Loading...