XD401
1000 User Digital Biometric ‘Fingerprint’
Access Control & Time/Attendance Unit
OPERATION MANUAL
p 2
I. Introduction …………………………………… 3
1.1 Basic Concepts …………………………………… 4
1.1.1 User Enrollment …………………………………… 4
1.1.2 User Verification …………………………………… 4
1.1.3 Match Threshold Levels …………………………………… 4
1.1.4 User ID Numbers …………………………………… 5
1.1.5 Authority (status) Levels …………………………………… 5
1.1.6 Start-up window …………………………………… 6
1.2 How to place the finger …………………………………… 6
II. Enrollment and Verification Procedures …………………….......... 7
2.1 Enrolling User …………………………………… 7
2.2 Testing an Enrollment …………………………………… 11
2.3 Enrolling a fingerprint for backup ……………………………............ 12
2.4 Verifying Your Identity …………………………………… 12
2.4.1 Fingerprint Verification …………………………………… 12
2.4.2 Password Verification …………………………………… 13
2.4.3 ID & Fingerprint …………………………………… 14
2.5 Hints for Successful Enrollments ……………………………............ 14
III. System Options …………………………………… 15
3.1 System Options …………………………………… 15
3.1.1 Date Time …………………………………… 16
3.1.2 Language …………………………………… 16
3.1.3 Lock Controller …………………………………… 16
3.1.4 Advanced Options …………………………………… 16
3.2 Power Manager …………………………………… 17
3.3 Communication Option …………………………………… 18
3.4 Log Options …………………………………… 18
3.5 Auto Test …………………………………… 19
IV. System Information …………………………………… 19
V. Maintenance …………………………………… 20
TABLE OF CONTENTS
p 3
I. Introduction
This chapter is about the Main Features of the XD401Fingerprint unit.
Product Appearance
Key Controls
• OK - Confirm key: Confirm your present operation.
• MENU - Menu key: Press down the key for seconds to enter the management
interface in the initial status.
•
Cancel key: Cancel your present operation.
• Scrolling up key: Scrolling up the menu
• Scrolling down key: Scrolling down the menu
• IN - Check for ON of work
• OUT - Check OUT of work
• Power key: Control the power on and off
• Door bell
p 4
1.1 Basic Concepts
This section contains definitions and descriptions of the XD401’s features, including:
· User Enrollment
· User Verification
· Match Threshold Levels
· User ID Numbers
· Authority (Status) Levels
The two most important XD401’s Functions are User Enrollment and User Verification.
1.1.1 User Enrollment
• Enrollment is the process to create an ID number and scanning a user’s finger to create
a template three times. This template is associated with a user ID number and stored.
• During user verification, the stored template is compared to the current fingerprint scan
to confirm the user’s identity.
• Enrollment is performed at designated units. The user can verify on the time recorder
that enroll his fingerprint. The enrollment process takes approximately 2 seconds.
• Up to ten fingers can be enrolled for the same ID number, so the user may have more
verifications way.
• Ideally, everyone finger on each hand should be enrolled so that if the user injures the
enrolled finger had, an alternate finger template is available. While recording the finger
type is optional, it is recommended such as left or right index, so that at verification the
user is prompted as to which finger to use.
1.1.2 User Verification
Verification occurs when a user either enters an ID number or places a finger in the
fingerprint sensor, then input password for comparison with the stored template.
1.1.3 Match Threshold Levels
The Mach Threshold is a number that represents the degree to which the verification is
examined to ensure that the person is the person claimed.
The Match Threshold Levels establishes a balance between False Acceptance Rate (FAR)
and False Rejection Rate (FRR). FAR measures how often a non-authorized user is falsely
recognized and granted access to the system. FRR measures how often an enrolled and
p 5
authorized user, who should be granted access to the system, is denied on the basis
that the system did not recognize him.
• You can set match threshold levels on a per-use basis. For the fingerprint verification
is difficult, you can adopt ID & Fingerprint verification (match one to one).
• Raising the threshold increases security, while lowering it increases throughout. The
correct balance is essential.
• For users with worn or damaged fingers, match threshold levels can (and should) be
reduced.
• Different sites have different requirements.
Table 1—1 Suggested Match Threshold Settings
1.1.4 User
ID Number
s
Before beginning fingerprint enrollment, a user is assigned User ID Number. This ID
number is used to call up the fingerprint template each time that verification is
requested.ID numbers are normally called up via the keypad, but they can be called up
through other means such as RF Card.
1.1.5 Authority (status) Levels
XD401 has four authority or status levels:
• Users are people whose identity must be verified, such to gain access to a facility or
to have their attendance recorded.
• Enrollers are Users who are authorized to enroll new users or delete on to the
system.
• Managers can do other operations, except set advanced option and enroll manager’s
authority.
• Supervisors are Users who access to all functions and change all setup in the system.
Note: Without Manager and Supervisor status in the system, the Enroller will enroll
them. And if there isn’t a Supervisor in the system, the Manager will enroll him.
FRR FAR One-to-many One-to-one
High Low 45 25
Middle Middle 35 15
Low High 25 10
p 6
1.1.6 Start-up window
Click the power button and the screen showed on, a display of a window was called the
Start-up window. The following appears:
1.2 How to place the finger
1.
The correct way is:
Place a finger flat on the sensor surface
Place it to the center of the sensor surface
2. The wrong way is:
Vertical Offset
Inclined Lower
Note: Please adopt the correct way to place the finger. Xvision is not responsible for the
malfunctioning results arising from improper pressing manners. Our company reserve
ultimate the interpreting and modifying right for this.
Welcome
-
-
p 7
II. Enrollment and Verification Procedures
This chapter describes how to enroll and verify users on the XD401 unit.
The following topics are included:
· Enrolling User
· Testing an Enrollment
· Enrolling a User with the Display Finger Option On
· Verifying Your Identity
· Hints for Successful Enrollments
Note: You must have Enroller, Manager, or Supervisor status to enroll users. For
information on status levels, see “Authority (Status) Levels” on 1.1.5.
2.1 Enrolling Users
If this is the first enrollment in a new or empty system, everyone will become an enroller.
If there is a manager in the system, you will have Manager status to enroll a new user.
There are three ways of enrollment, fingerprint enrollment, password enrollment,
fingerprint & password are suitable for three differences crowds.
•
Fingerprint enrollment suited the most people who have better quality fingerprints;
• Fingerprint & Password suited few people who enrolling successful, but verification
was difficult;
• Password enrollment suited 1% people who verification unsuccessful.
To start the enrollment process, identify yourself firstly - press [Menu], enter your ID
number or fingerprint, and then verify your identity.
Note: If this is the first enrollment in a new or empty system, you will not be prompted for
verification.
The following message appears on the display:
Menu
Ź User Manage
Options
Sys Info
p 8
Press [OK], access the User Manager, the following message display:
Press [OK], access the User Enrollment, the following message display:
1.
Fingerprint Enrollment
(1) Access the Enroll Fingerprint to press [OK], the following display:
(2) Press [OK], the following
appears:
(3) Input the enrolling
number (the range is 1 to
65534), press [OK], the
following appears:
User Manage
ŹEnroll User
Enroll Admin
Enroll User
ŹEnroll FP
Enroll Pwd
N
ew Enroll
Enroll No 00001
ESC OK
[ ], the following appears:
N
ew Enroll
Enroll No 00008
ESC OK
N
ew Enroll
Place Finger…
ESC
p 9
(4) If the test is successful three times in a row, the following appears:
Note: 07711-1: The last number 1 means the first fingerprint.
Press [OK], the previous message continues to be displayed while the template is created.
If your identity cannot be verified, you are prompted to try again. And you must restart the
verification procedure (step 3).
2. Password Enrollment
(1) Access the password enrollment, press [OK], the following appears:
(2) Press [OK], the following appears:
(3) Input the enroll number (the range is 1 to 65534), press [OK], the following appears:
Note:
T
he password range is
1 to 5.
N
ew Enroll
00008-1
ESC OK [Save]
T
Enroll Pwd
New Enroll?
ESC OK
N
ew Enroll
Enroll No 00008
ESC OK
N
ew Enroll
Input Pwd *****
p 10
(4) Input the password, press [OK], the following appears:
(5) Input the password again, press [OK], the following appears:
Note: 00008-P: The last letter P means password.
Press [OK], the previous message continues to be displayed while the template is created.
3.Fingerprint & P
asswor
d
(1) Access the Fingerprint& Password, press [OK], the following appears:
(2) Press [OK], the following appears:
(3) Input the password
(range is 1 to 65534),
press
[OK], the following appears:
N
ew Enrollment
Input Pwd: *****
Pwd Affirm: *****
ESC OK
N
ew Enroll
00008-P
FP & Pwd
New Enroll
N
ew Enroll
Enroll No 00008
N
ew Enroll
Please finger…
p 11
(4) If the test is successful three times in a row, the following appears:
(5) Input your password, the following appears:
(6) Input the password again, press [OK], the following appears:
Note: 00008-1P: The second from the last 1 means one fingerprint. The last letter P means
password.
Press [OK], the previous message continues to be displayed while the template is created.
2.2 Testing an Enrollment
Ask the users to place their finger to perform a test verification. If the test was successful,
you will adopt Fingerprint enrollment. If the poor quality of fingerprint, you will be
recommended to use Fingerprint & Password.
N
ew Enroll
Input Pwd: *****
N
ew Enroll
Input Pwd: *****
Pwd Affirm: *****
N
ew Enroll
00008-1P
p 12
2.3 Enrolling a User with the Display Finger Option On ( for backup)
Press [ESC] to the Display Finger Option On, the following appears:
Note: Where system memory permits, it is advisable to have at least two fingers enrolled
for a long-term user.
2.4 Verifying Your Identity
If visitors use XD401 to verify their identity, the system defaults to three ways of
verification: Fingerprint verification, Password verification, ID number & Fingerprint. The
following appears:
2.4.1 Fingerprint
Verification
Place the finger on the sensor surface, the following appears:
It continues for about 0.5 seconds. If the test is successful, it will say “Thank you”, the
following appears:
N
ew Enroll
Enroll No 00008
Esc Ok
Display
Enroll No 00008
Esc Ok
ESC
g
FP Verify
Please Move Finger
FP Verify
Enroll No 00008
Verified!
p 13
If your identity cannot be verified, you are prompted to try again, the following appears:
It continues for about 0.5
seconds, return to the
start-up window.
2.4.2 Password Verification
To start the enrollment process, enter your ID number, the following appears:
Press [OK], the following appears:
Input correct password, press [OK], the following appears:
If the password cannot be verified, the following appears:
FP Verify
Place Finger Agn
1:1 FP Verify
Enroll No 8
ESC OK [Pwd]
Pwd Affirm
Enroll No 8
Input Pwd: *****
Pwd Affirm
Enroll No 00008
Verified!
Pwd Affirm
No 8
Error pwd !
p 14
2.4.3 ID number & Fingerprint
To start the enrollment
process, enter your ID
number, the following
appears:
If your identity is verified,
the following appears:
2.5 Hints for Successful Enrollments
The fingerprint is of good quality, the verification speed will be fast; Otherwise, it will
verify slowly or occur to FRR.
Table 2-1 Enrolled unsuccessful or the fingerprint of poor quality
1:1 FP Verify
Enroll No 8
ESC OK [Pwd]
P
1:1 FP Verify
Enroll No 8
ESC OK [Pwd]
P
1 1 FP Verify
Enroll No 00008
Verified!
1
Dry or dirty fingerprints
• If the fingerprint is dry, you can adopt the way of wetting up the finger,
such as breatheing at the finger’s tip. Pls. keep your finger in clean.
Have no enough to
bring pressure
The user should place a finger firmly and squarely on the sensor surface.
How to select the
finger?
• Recommend to left or right index or middle finger.
• Use fingerprints of good quality, without worn or hurt.
• The user usually selects the forefinger, if it was of a poor quality, you will
be recommended to middle finger or ring finger.
• If the user’s finger is less, you will select the thumb.
How to place the
finger?
• Place your finger firmly and touch the sensor surface must be over 2/3.
• The fingerprint does not touch upright on the sensor surface. Do not touch
the finger too fast; Do not move the finger on the sensor surface.
The influence of the
fingerprints change
• For users with worn or damaged fingers, the identification can be
influenced.
• If the finger quality was poor, you will select password verification.
Others
• However, few people’s fingerprint quality is too poor to verify the
fingerprint in gear. Please use ID & fingerprint verification, and the Match
Threshold Levels can be reduced or use password verification.
p 15
III. System Options
Press the [Menu], then verify your identity. The following appears:
Access Options, press [OK], the following appears:
The following topics included:
· System Options
· Power Manage
· Communication Options
· Log Options
· Auto Test.
3.1 System Options
Access System Opt, the following appears:
The setup facility covers four areas:
System Options
,
Language, Lock and Advanced
Options.
Menu
User Manage
Options
Sys Info
Options
System Opt
Power Mng
Comm Opt
System Opt
Date Time
Language ENG
Lock No
p 16
3.1.1 Date Time
Access Date Time, the following appears:
3.1.2 Changing the Default Language
Access Language, press [OK], it defaults to SCH. Press to select another language. The
XD401 unit comes with three built-in languages, simplified Chinese, traditional Chinese,
and English for all displays. Select the language that you will use, press [OK], then Press
[ESC] to return the Options. The system will ask for confirmation of the displayed
language. Press [OK] to accept the language displayed.
3.1.3 Lock Controller
It defaults to close the lock signal output in the system. If you use access control feature,
you will change [No] to [Yes], press [OK] to confirm, and then press [ESC] to return the
Options. The system will ask for confirmation of the displayed controller, press [OK] to
confirm.
3.1.4 Advanced Options
Access Advanced Option, press [OK], the following appears:
Press and to scroll up or down the screen to select the option.
• Restore Default: restore all setup information to default.
• Clear all Data: delete all enrolling fingerprints and logs.
• Delete Logs: delete all logs of flash disk.
• Clear Managers’ rights: change the managers’ rights into ordinary users’ rights.
Date Time
2004-01-02
08:24:35
Adv Option
Restore Deflt
Del Logs
p 17
• Show Score: whether show the quality value of fingerprint in the screen or not;
• Match Threshold Levels: For helping in selecting threshold level settings, see Table
1.1.3.
• Sound: whether use to phonic hint or not.
3.2 Power Manager
Access Power Manage, the following appears:
This product uses smart manage system, supports the time switch and resting features, it
can satisfy the user’s different demands.
• Shutdown: auto shut-off in the timed.
• Power on: auto open-up in the timed.
• Sleep: automatic resting in the timed, press any key to enter working state.
• Idle and Idle Minute: they are related each other, while the idle minute is zero, the idle
is closed; while the idle minute is not zero (unit was minute), for example, it is one
minute, the user does not do anything in one minute, the system will enter the idle
state.
Select Shutdown, press [OK], the following appears:
Press [OK], then enter Shutdown,
press [ESC] to cancel.
Power Mng
Shutdown No
Power On No
Sleep No
Power Mng ł
Sleep No
Idle Off
Idle Min 0
Shutdown
Setup On time Fun?
ESC OK
w
p 18
3.3 Communication Options
Access Comm Opt, the following message appears:
The XD401 supports RS232, RS485, TCP/IP, whether you use Single-Board Computer (SBC)
or Networking Computer.
• Device Number: machine ID, the range is 1 to 255.
• Baud Rate: there are three options, 9600, 38400, 115200; The speed of communication
is fast, recommend to use RS232; The speed of low communication is stable,
recommend to use RS485.
• IP address: it defaults to IP address is 192.168.1.201.
• Ethernet: whether use TCP/IP protocol or not.
• RS232: whether use RS232 or not.
• RS485: whether use RS485 or not.
3.4 Log Options
Access Log Opt, the following message appears:
• Alarm Attendance Log: when the remainder log capacity reached set numerical value,
it will automatically sound a warning that logs were fulled.
• Recheck Minute: Set within compass (Unit: minute). Someone’s enrollment has
enrolled, then, the log twice was not displayed in the system.
Comm Opt
Dev Num 1
Baud Rate 1115200
IP address
Comm Opt ł
Ethernet No
RS232 Yes
RS485 Yes
Log Opt
Alm AttLog 1
ReCheck Min 0
p 19
3.5 Auto Test
Access Auto Test, the following message appears:
In the option, you can run system device test. If the unit breaks down, it can analyse the
cause of the device’s fault and the devices were quickly and easily maintained.
It tests the Memory, LCD, Sound, Fingerprint sensor, keypad and clock. During the course
of the test, you should guarantee the stability of the power. Otherwise, the system’s
hardware was probably damaged, especially if it runs the memory test.
IV. System Information
Access [Menu] to Sys Info, press [OK], the following appears:
It displays user numbers, password numbers,
fingerprint numbers, manager and log numbers in the
screen. You can see some information such as the
remainder log capacity in the memory, the device
capacity, the defaults date, machine number and
manufacturer information are in the system.
Auto Test
Run All Test
Flash Test
Auto Test ł
FP Reader
Key Test
Sys Info
User Cnt 206
FP Cnt 173
Att Log 8046
S
Sys Info
User Cnt 206
FP Cnt 173
Att Log 8046
S
Sys Info
User Cnt 206
FP Cnt 173
Att Log 8046
S
Sys Info
Admin Cnt 0
Pwd User 37
Res. Space In
f
Sys Info ł
Pwd User 37
Res. Space Inf
Dev Info
p 20
V. Trouble shooting
1 Cleaning
From time to time, the optical platen, the keypad and display window require cleaning.
Since working environments differ, it is not possible to define when cleaning should be
performed.
Table 5-1 Cleaning Schedule
2. Cleaning the K
eypad and Display
To clean the keypad and display, use the same cleaning products as for the platen, and
wipe dry.
3 Cleaning the Optical Platen
Clean the optical platen as follows:
• (1) If dusty or gritty, first blow on the platen to clean off any loose particles.
• (2) Spray on a light coating of a window cleaning product or other similar neutral
detergent. Warning: Do not use any other cleaner or the platen may become damaged.
• (3) Using a non-abrasive and lint-free cloth, pat dry. Be careful not to scratch the platen.
If lint particles adhere to the platen surface, blow them off when the platen is dry.
I t em C l ea n i n g F r eq u en c y
Keypad and display window
Cleaning when visibly dirty and hard to read. See cleaning the keypad and
display below.
Do not over clean. The platen is designed to work under greasy or dirty
conditions.
Optical platen
However, do clean if the platen is obstructed or people are reporting
deteriorating performance. See cleaning the Optical Platen below.
Loading...