Xtrons DR SERIES User Manual

REV0.0

DR Series User Manual

No boot up.

Fault

Af ter ignition starting
up and power off, all
settings information
were missing.

Poor receive stations
effect

No way to put into
Optical disc

No remote control
action/function

Disc can't play

No action to switch
between Language
and sub-title

No image

Mode screen
dislocation

Functional disorders

Solution

Af ter pressing the RESET key
with a small nib on the face
panel, power on again.

Re-connect the shunting line

Using the same insurance
with main unit to replace

Pop-up the disc in the unit
(device) , then re-insert it
into again.

Checking if the ANT of radio
automatic antenna control
lines ar

e not connected well,
then, please re-check the
antenna and the ground wire
made correct connection all.

replace(change) the battery
of the remote control.

Change the good disc

Using pick up head cleaning
disk to clear the pick up.

Put the face of optical disk
logo upwards and put it into
the device(unit).

No multilingual sub-title's disk .
Can't make switch between
language and sub-title

Re-connect the connection
line.

Calibrate touch screen,press” “
button for 5seconds to calibration
interface.(neednt for capacitive
touch screen).

Af ter pressing the resetting key
of "RESET" with a small nib on
the face panel(plate),to

re-boot up.

Power fuse was burnt.

Reason

The BATT of ACC ignition
positive power linemade
wrong connection.

Other factors caused the
microprocessorincorrect
operation

Low battery in the remote
control

Car antenna didn't go out ,
Poor antenna grounding.

Disc was scratched

The laser head has been
dirty

Optical disk's positive
and negative were
placed reversal(opposite).

There has installed disks
already in the DVD loader
/mechanism.

CD only burned a
language/ sub-title

No making touch screen
calibration ver y well.

No connect the video
cables very well from
main unit to TV.

Other factors caused the
microprocessorincorre

ct

operation

Common Troubleshooting Guide

1、Enter into bluetooth interface,if not paired with mobile phone,will

appear ”no connection”

2、Open mobile phone bluetooth and search device,search name of ”rk-

px3”,click connection.Some mobile phone maybe ask pairing

password,pls input”0000” and complete connection.If connected

successfully,”no connection”will disappear.

3、Synchronous phonebook,in the”phonebook”page,click”download

phonebook”,the phone will appear synchronized request,click”ok”to

complete synchronization.If too many on the phonebook,need to take a

few minutes to download,just wait with patience.

4、Dialing a call,just input phone number on the keyboard directl

y,press

”dial”button will be ok

5、Bluetooth music,on the bluetooth music interface to play music,also

operate”play/pause”,”las/next”functions.

Note:when playiing music,pls open music player on the phone

first,because it cannt open player on the phone,if installed a few

players,just open one of them.

Bluetooth using method

Password：0000

Click“ ” icon on the main UI to enter into the setup interface

1、Click“ ”in the carset interface,and then click“ ”to

enter into steering wheel setting interface.

2、At first,press “ ”button to remove all old datas.

3、Set the buttons as tips on the screen.Note:when prompt press

button the wheel,pls hold 0.5s-1s,cannt relax too early.

4、Press“ ”button to save the settings after the setup completed.

5、When setup errors need to be reset,pls repeat above 2-4 operation.

6、Some cars with CAN-BUS neednt set steering wheel,pls ignore

this part.

Note:make sure”button wire”on the steering wheel connected well with”SWC”
on the unit,as shown below:2 CSW wire connected with anode of steering wheel
button wire,GND conneted with cathode

Steering wheel button settings