XL-VCF104M (CO)
XL-VCF104S (CPE)
VDSL2 CO/CPE modem
User’s Guide
VDSL2 Point to Point Solution
VDSL2 (Very-High-Bit-Rate Digital Subscriber Line 2, ITU-T G.993.2 Standard) is an access technology that exploits the
existing infrastructure of copper wires that were originally deployed for POTS
services. It can be deployed from central
offices, from fibre-fed cabinets located near the customer premises, or within buildings.
ITU-T G.993.2 VDSL2 is the newest and most advanced standard of DSL
broadband wireline communications. Designed
to support the wide deployment of Triple Play services such as voice, video, data, high definition television (HDTV) and
interactive gaming, VDSL2 enables operators and carriers to gradually, flexibly, and cost efficiently upgrade existing
xDSL-infrastructure.
ITU-T G.993.2 (VDSL2) is an enhancement to G.993.1 VDSL
that permits the transmission of asymmetric and symmetric
(Full-Duplex) aggregate data rates up to 200 Mbit/s on twisted pairs using a bandwidth up to 30 MHz.
VDSL2 deteriorates quickly from a theoretical maximum of 250 Mbit/s at 'source' to 100 Mbit/s at 0.5 km and 50 Mbit/s at
1 km, but degrades at a much slower rate from there, and still outperforms VDSL
equal to ADSL2+
.
. Starting from 1,6 km its performance is
ADSL-like long reach (LR) performance: ADSL-like long reach performance is one of the key advantages of VDSL2.
LR-VDSL2 enabled systems are capable of supporting speeds of around 1-4 Mbit/s (downstream) over distances of 4 to
5 km, gradually increasing the bit rate up to symmetric 100Mbit/s as loop-length shortens. This means that VDSL2-based
systems, unlike VDSL1 systems, are not limited to short loops or MTU/MDUs only, but can also be used for medium
range applications.
1
CONTENT
1.Unpacking Information ................................................................................... 3
Check List.......................................................................................................... 3
2. Installation ..................................................................................................... 4
Hardware Installation......................................................................................... 4
2.1 Pre-installation Requirements................................................................. 4
General Rules ............................................................................................... 5
Connecting the VDSL2 CO&CPE Modem .................................................... 5
3. Hardware Description .................................................................................... 7
4. Setup the VDSL2 CO&CPE Modem by Web Browser ................................ 10
4.1 Login. .................................................................................................... 10
4.2 Select the Menu Level .......................................................................... 11
4.3 Select Advanced Setup......................................................................... 12
4.4 Select LAN ............................................................................................ 13
5. Building a VDSL2 System .................................................................………16
5.1 Connect the CPE and the CO to the Line............................................. 16
5.2 Connect the CPE and the CO to LAN Devices..................................... 17
5.3 Run Demos and Tests........................................................................... 17
6. Operating the VDSL2 System ..................................................................... 18
6.1 Configuration Settings .......................................................................... 18
6.2 Status Displays ..................................................................................... 26
7. Configuration Interface of the Router .................................................. …….31
7.1 Logging on to the VDSL2 CO&CPE Modem ........................................ 31
7.2 Configuration Menu for Administrators ................................................. 32
Appendix A: Product Features & Specification ................................................ 68
Appendix B: Compliance and Safety Information............................................ 70
2
1.Unpacking Information
Check List
Carefully unpack the package and check its contents against the checklist.
Package Contents
●
VDSL2 Modem (VDSL2 CO Modem / VDSL2 CPE Modem)
●
Two plastic feet
●
User’s Manual
●
AC to DC 12V Power Adapter
●
RJ-45 cable
●
RJ-11 cable
Please inform your dealer immediately for any missing, or damaged parts. If possible, retain the carton,
including the original packing materials, Use them to repack the unit in case there is a need to return for
repair.
3
2. Installation
Hardware Installation
This chapter describes how to install the VDSL2 CO&CPE MODEM and establishes network connections. You
may install the VDSL2 CO&CPE MODEM on any level surface (e.g, a table or shelf). However, please take note of
the following minimum site requirements before you begin.
2.1 Pre-installation Requirements
Before you start actual hardware installation, make sure you can provide the right operating environment, including
power requirements, sufficient physical space, and proximity to other network devices that are to be connected.
Verify the following installation requirement:
●
Power requirements: DC12V/1A or above.
●
The VDSL2 CO&CPE MODEM should be located in a cool dry place, with at least 10cm/4in of space at the front
and back for ventilation.
●
Place the VDSL2 CO&CPE MODEM out of direct sunlight, and away from heat sources or areas with a high
amount of electromagnetic interference.
●
Check if network cables and connectors needed for installation are available
4
General Rules
Before making any connections to the VDSL2 CO&CPE MODEM, note the following rules:
●
Ethernet Port (RJ-45)
All network connections to the Modem Ethernet port must be made using Category 5 UTP for 100Mbps;
Category 3,4 UTP for 10Mbps
No more than 100 meters of cabling may be use between the MUX or HUB and an end node.
●
Phone Port (RJ-11)
All Phone set connections to the RJ-11 Port made using 24~26 Gauge phone wiring.
Connecting the VDSL2 CO&CPE MODEM
The VDSL2 CO&CPE MODEM can be controlled by a PC, henceforth, called the "Control PC". For this purpose, you
needa PC with an Ethernet network interface and a DB-9 RS232 serial interface. Two programs are required: A Web
browser is mandatory and a terminal program should be available optionally. The board has several connectors.
4 Ethernet RJ45 jacks (connect LAN devices to route); the Auto MDIX feature of the ports switches automatically
between MDI and MDI-X (MDI = Media Dependant Interface), therefore straight Ethernet cables can be used.
2 x RJ11 jack (LINE Port is for connects VDSL client side to Line Interface, Phone port is for connects phone set or
FAX machine)
1 x Console port (monitoring, access to operating system via shell for firmware downloads, starting drivers and web etc.,)
1 Power Supply (as described above)
5
Figure 2.1 VDSL2 Point to Point application
6
3. H a r d ware Description
This section describes the important parts of the VDSL2 CO&CPE MODEM. It features the front indicators and rear
connectors.
Front Indicators
The following figure shows the front panel.
Figure Chapter 3.1 VDSL2 CO Modem
Figure Chapter 3.2 VDSL2 CPE Modem
7
r
Six LED indicators.
At a quick glance of the front panel, it will be easy to tell if the Modem has power, signal from its Ethernet
RJ-45 port or there is phone line signal RJ-11port
Front Indicators
LED Description and Operation
The Modem has three LED indicators.
LEDs Status Descriptions
PWR
(Ready LED)
E1~E4
(Ethernet
LED)
Link
(VDSL LED)
Steady
Green
Steady
Green
Flashing
(LINK/ACT)
Steady
Green
It will light up (ON) to show that the product is
power good, and system reset OK.
Each RJ-45 station port on the Ethernet is
assigned an LED light for monitoring port “Good
Linkage”. LED is normally OFF after the powe
on operation, but will light up steadily to show
good linkage and flashing to show data
transmission.
RJ11 station port on the VDSL is assigned an
LED light for monitoring port “Good Linkage”.
LED is normally OFF after the power on
operation, but will light up steadily to show good
linkage.
8
Rear Panel
The following figure shows the rear connectors
Figure Chapter 3.3 Rear Connectors
VDSL2 CO&CPE MODEM Rear Connectors
Connectors
Line
Phone
E1~E4 For connecting to a Ethernet equipped device RJ-45
Console port
Power On
Description Type
For connecting to the VDSL Modem Using
a RJ-11 cable
For connecting to the telephone or FaxISDN
Modem
For connecting to PC with RS-232 serial
port over a D-SUB Cable
RJ-11
RJ-11
RS-232
1. Check the adapter is properly connected.
2. Verify the power LED is steadily on.
9
4. Setup the VDSL2 CO&CPE MODEM by Web Browser
The VDSL2 CO&CPE MODEM provides a built-in web browser. You can use Web browser to configure the VDSL2
CO&CPE Modem. First please input the IP address 192.168.16.249 (VDSL2 CO Modem) and 192.168.16.250
(VDSL2 CPE Modem) in the Web page.
4.1 Login.
The password is “admin“.
Figure 4.1 Login
10
4.2 Select the Menu Level
There is a simple Setup Wizard for end users and an Advanced Setup. The focus of this manual is on the Advanced
Setup.
Figure 4.2 Select the Advanced Setup in the Entry Screen
11
4.3 Select Advanced Setup
Select the Advanced Setup. The menu below will be used frequently. As an exercise and an example now the IP
address will be set.
Attention: The settings in the following Chapter 4.4 only need to be performed in order to change LAN settings. Such
a change may be necessary when connecting the VDSL2 CO&CPE Modem for the to a new control PC
and/or in order to turn the IP address changed via a shell command into a default address for the next
restart of the board.
Figure 4.3 Advanced Setup
12
4.4 Select LAN
The menus below will not be used very often. But when connecting the VDSL2 CO&CPE Modem to a new control
PC, you may want to go through the following steps in order to make the IP address previously set by ifconfig in the
terminal console permanent. Or on some later occasion you may want to change it again without using the console.
Then the menu below will help you too.
In order to set the IP address, click on “LAN Settings”.
Figure 4.4 LAN menu
13
4.4.1 Select LAN Settings and set the IP Address
The form below is used to change the IP address of the LAN port “adm0” in the VDSL2 CO&CPE Modem.
The proposed IP address either is the default address of adm0 or it is the address changed by an ifconfig
command via the shell running in the terminal.
The Subnet Mask display can be ignored.
In case the DHCP checkbox is checked, some additional data and options will be on display (see Chapter
6.2.5.1 on Page 50). The DHCP server is not required to work with VDSL2 in a lab environment. It is
recommended to uncheck the box if it is not unchecked already.
Figure 4.4.1 LAN Settings
14
Now the IP address either may be changed or left as it is. If it has been changed in the form or after it has been
changed using the ifconfig command via the shell running in the terminal, it needs to be stored permanently Hit
the “APPLY” button in order to make the displayed IP address new default address.
4.4.2 Restart the Settings Dialog
After the “APPLY” button has been hit, the displayed IP address “adm0” port will be stored in a non volatile
memory on the VDSL2 CO&CPE Modem. Also, the Ethernet link between the control PC and the VDSL2
CO&CPE Modem will be re-initialized – even if the IP address has not been changed. Refresh the display of
the HTTP browser running on the control PC and login again.
The VDSL2 CO&CPE Modem now is prepared to be controlled by the control PC.
Figure 4.4.2 Login after Storing the IP Address as Default Value
15
5. Building a VDSL2 System
First a quick overview over a complete setup:
Figure 5 VDSL2 Application
5.1 Connect the VDSL2 CO Modem and the VDSL2 CPE Modem to the Line
The objective for VDSL2 is passing data over a twisted pair cable at high speed. In the setup, either such a cable
connects the VDSL2 CO Modem and the VDSL2 CPE Modem, or a line simulator or any other hardware
representation of a cable network, with or without noise injection and crosstalk simulations.
16
5.2 Connect the VDSL2 CO Modem and the VDSL2 CPE Modem to LAN Devices
In the setup, usually a Ethernet tester serves as representation of the LAN side as well as representation of the
WAN side.
5.3 Run Demos and Tests
The Ethernet tester may send data downstream as well as upstream. It also receives the data in order to check
the integrity of the data transmission.
Different data rates can be tested under different line conditions.
17
6. Operating the VDSL2 System
After the VDSL2 system has been set up, you may want to configure the settings which are related to VDSL2.
Configuration of operation modes, test modes (loop back) and the display of status information is supported by an
graphical user interface.
6.1 Configuration Settings
Configure and start the VDSL2 CO Modem and the VDSL2 CPE Modem.
Configuration: As a minimum configuration, usually selecting the bandplan is required.
See Chapter 6.1.3, Profile Configuration.
Next, both sides should be activated from the web interface.
See Chapter 6.1.6, Line Activation
The connection status of the link can be monitored.
See Chapter 6.2.1, Line Status
18
6.1.1 Channel Configuration
Figure 6.1.1 Channel Configuration Menu
19
Channel Configuration Settings
Setting
Description
Channel Number To which bearer channel number shall the settings apply?
Channel 0
Direction To which direction shall the settings apply?
Upstream
Downstream
Min Data Rate Minimum Payload Data Rate
Max Data Rate Maximum Payload Data Rate
Max Int Delay Maximum Interleaver Delay
20
g
Targ
)
6.1.2 Line Configuration
Figure 6.1.2 Line Configuration Menu for SNR Margin Selection
Line Configuration
Settin
Description
Direction Select the target direction.
et SNRM Set the required SNR Margin *10 (50=5dB
21
.
6.1.3 Profile Configuration
Figure 6.1.3 Profile Configuration
22
6.1.4 Band Configuration
Figure 6.1.4 Band Configuration
23
g
g
r
6.1.5 Loop Back
Loop Back
Settin
Channel
Number
Figure 6.1.5 xTC Loop Back Activation/Deactivation Menu
Description
To which bearer channel number shall the settings apply?
Channel 0
xTC Activate or deactivate loopback within the Transmission
Conver
ence laye
.
24
g
A
)
6.1.6 Line Activation
Figure 6.1.6 Activation and Deactivation of the Line
Line Activation/Deactivation
Settin
Line Activate or deactivate the line. (Select the activity and the press
Description
the
PPLY button.
25
6.2 Status Displays
6.2.1 Line Status
The following status messages may occur: not_initialized, exception, idle request, idle, silent request, silent, handshake,
full init, discovery, training, analysis, exchange, showtime no sync, showtime tc sync, fast retrain, lowpower l2,
loopdiagnostic, loopdiagnostic complete, resync, test, lowpower l3, unknown
Figure 6.2.1 Line Status Display: Actual SNR
26
6.2.2 Channel Status
Figure 6.2.2 Channel Status Display: Data Rate, Delay, Error Counters and Impulse Noise Protection
27
6.2.3 XTC Status
Figure 6.2.3 Display of xTC Status
28
6.2.4 Version Info
Figure 6.2.4 Display of Version Data
29
6.2.5 Graphs
Figure 6.2.5 Display of SNR per Carrier
30
7. Configuration Interface of the Router
This section explains how to configure the router section of the VDSL2 CO&CPE Modem using its web-based
configuration.
The parts of the circuitry as well as the router configuration menu has been ported from that of the reference kit to the
VDSL2 CO&CPE Modem reference board. As for the menu, There are only a few differences:
●
The “adm1” port now is the port to the VDSL2 side. The port on the LAN is “adm0”. It supports four Ethernet
connections.
●
The IP addresses are used in this chapter are different from the examples in the previous chapters.
●
The password used in this chapter is different from the examples in the previous chapters.
●
The VDSL2 CO&CPE Modem of course has no menu option for VDSL settings. The VDSL2 CO&CPE Modem has
a VDSL menu which is described in Chapter 6. Also the entry menu (Chapter 4.2) has different “looks” tailored to
the VDSL2 CO&CPE Modem.
7.1 Logging on to the VDSL2 CO&CPE Modem
To log on to the VDSL2 CO&CPE Modem Web Application, you must have a valid password. The Administrator
creates the log on user with its password. When you log on to the VDSL2 CO&CPE Modem Web Application, the
USER LOGIN window is displayed as shown in Figure 7.1.
Figure 7.1 VDSL2 CO&CPE Modem Web Application
31
In the USER LOGIN window:
1. Enter the password in the Password text box. For an Admin user, the default password is “admin”.
2. Click LOGIN to begin the configuration or click CANCEL in the USER LOGIN window to cancel this log on operation.
7.2 Configuration Menu for Administrators
This chapter is only for Administrators.
The Homepage is the first screen displayed when a user logs on to the VDSL2 CO&CPE Modem Web Application.
The VDSL2 CO&CPE Modem Web Application is categorized into two modules:
1. Setup Wizard — An easy-to-use setup wizard provides the most common configurations.
2. Advanced Setup — Advanced setup features allow the user to configure all the functions that are supported by the
VDSL2 CO&CPE Modem like Firewall, routing, and UPnP.
7.2.1 Setup Wizard
The Setup Wizard is designed for ease-of-use in order to quickly configure the most common settings. The Admin can
view the Setup Wizard link in the homepage. The wizard’s first step that allows the admin to configure the system
host settings displayed as shown in Figure 7.2.1.
Figure 7.2.1 Setup Wizard’s First Step
There are five steps to complete the wizard. Follow the instructions given in each step and enter the desired settings.
32
7.2.2 Advanced Setup
Click on the Advanced Setup link in the homepage in case you want to configure a wider range of settings. The
following configuration options are displayed in the left navigation bar, as shown in Figure 7.2.2:
• System
•
•
•
•
•
•
WAN
LAN
NAT
Firewall
Route
UpnP
Figure 7.2.2 Advanced Setup
33
7.2.3 System
The System link can be viewed in the left navigation bar. The following are the options available under System, as
shown in Figure 7.2.3 :
• Host Name
•
System Time
•
Administrator Settings
•
Firmware Upgrade
•
System Status
• S
ystem Log
•
Reset
Figure 7.2.3 System in the Left Navigator Bar
34
7.2.3.1 Host Name
To configure System settings, the user has to enter host and domain name. Click on the Host Name config link in the left
navigation bar. A screen is displayed as shown in Figure 7.2.3.1:
Figure 7.2.3.1 Host Name Configuration
The screen contains the following details:
Fields in Hostname
Field Description
Host Name Enter the host name of the VDSL2 CO&CPE Modem.
Domain Name Enter the domain name of the VDSL2 CO&CPE Modem.
35
r
Click CANCEL to exit from this page without saving the changes.
Click APPLY to save the information that has been entered.
7.2.3.2 System Time
To configure the system time zone, click on the System Time link in the left navigation bar. A screen is displayed as
shown in Figure 7.2.3.2:
Figure 7.2.3.2 System Time Configuration
The screen contains the following details:
Fields in System Time
Field Description
Set Time Zone Synchronize the system clock with the SNTP serve
.
Click CANCEL to exit from this page without saving the changes.
Click APPLY to save the information that has been entered.
36
7.2.3.3 Administrator Settings
To add a user or change user’s password, click on the Administrator Settings link in the left navigation bar. A screen is
displayed as shown in Figure 7.2.3.3.
Figure 7.2.3.3 Administrator Settings Configuration
While adding a user, each user must be assigned a separate port. Hence the number of users that can be added to the
system depends on the number of ports available on the VDSL2 CO&CPE Modem.
37
r
T
The screen contains the following details:
Fields in User Setting
Field
Description
Current
Password
Password This is the password of the login administrator.
Re-type
Password
Auto-Logout
ime
Click CANCEL to exit from this page without saving the changes.
Click APPLY to save the information that has been entered.
This is the password associated with the administrator. This is enabled only for the
use
Administrator login.
This is the password verification.
The auto-logout time, at least one minute.
38
7.2.3.4 Device Mode
The ADM5120 network processor used in the reference system is able to act as either a switch or a router. Clicking on
Device Mode on the left navigation bar allows the user to change the mode of operation, as shown in the following figure.
Figure 7.2.3.4 Device Mode
39
7.2.3.5 Firmware Upgrade
To update the system firmware, click on the Firmware Upgrade link in the left navigation bar. A screen is displayed as
shown in Figure 34. NEW Image JTC
Figure 7.2.3.5 Firmware Update
The screen contains the following detail:
Click Browse to select a specified file name to change the File Name.
Click APPLY to start the firmware update.
40
7.2.3.6 System Status
To view system status, click on the System Status link in the left navigation bar. A screen is displayed as shown in
Figure 7.2.3.6. NEW IMAGE JTC
Figure 7.2.3.6 Status Window
This screen displays the status of certain important system parameters. It also offers control over the current DHCP lease
for the IP Address.
Click Release to release IP Address for the WAN interface.
Click Renew to renew the IP Address for the WAN interface.
41
7.2.3.7 System Log
To view the system logs, click on the System log link in the left navigation bar. A screen is displayed as shown in
Figure 7.2.3.7.
Figure 7.2.3.7 Security Logs
The screen contains the following details:
Fields in Security Logs
Field Description
Log File This lists all the system
events.
Click Download to download the log file to the computer.
42
Click Clear to clear this page.
Click Refresh to retrieve system event and update the log file.
7.2.3.8 Reset
To restart the system, click on the Reset link in the left navigation bar. A screen is displayed as shown in Figure 7.2.3.8.
Figure 7.2.3.8 Reset VDSL2 CO&CPE Modem
Click Reset to restart the system.
43
7.2.4 WAN
The WAN settings can be viewed in the left navigation bar. The following are the options available under WAN, as shown
Figure 7.2.4:
• Dynamic IP
•
Static IP
•
PPPoE
•
DNS
Figure 7.2.4 WAN Setting in Left Navigator Bar
44
7.2.4.1 Dynamic IP
To configure the WAN interface to dynamically obtain an IP Address, click on the Dynamic IP link in the left navigation bar.
A screen is displayed as shown in Figure 7.2.4.1.
Figure 7.2.4.1 Dynamic IP Configuration
The screen contains the following details:
Click APPLY to save the information that has been entered.
Click CANCEL to exit from this page.
45
7.2.4.2 Static IP
To configure the WAN interface to use a Static IP Address, click on the Static IP link in the left navigation bar. A screen is
displayed as shown in Figure 7.2.4.2.
Figure 7.2.4.2 Static IP Configuration
The screen contains the following details:
Fields in Static IP
Field
Description
IP Address assigned by your ISP Enter the IP Address of VDSL2 CO&CPE
Modem.
Subnet Mask Enter the Subnet Mask of VDSL2 CO&CPE
Modem.
46
Fields in Static IP (cont’d)
Description
Field
ISP Gateway Address Enter the Gateway address of the VDSL2
Does ISP provide more IP
Address
CO&CPE MODEM.
Provides more IP Addresses of the WAN
interface. Select the check box to enable this
option. A screen is displayed as shown in Figure
41. Click Add to add IP Address and Subnet
Mask.
47
g
7.2.4.3 PPPoE
To configure the WAN interface to use PPPoE, click on the PPPoE link in the left navigation bar. A screen is displayed as
shown in Figure 7.2.4.3.
Figure 7.2.4.3 PPPoE Configuration
The screen contains the following details:
Fields in PPPoE
Field Description
User Name Enter a name to use the PPPoE session.
Password Enter the password of the login user.
Retype Password Enter the password a
Service Name Enter a service name.
ain to reconfirm.
48
y
f
Fields in PPPoE (cont’d)
Description
Field
MTU Enter the maximum connection units of the
PPPoE. The MTU range is 1400 to 1492 bytes.
B
default, it is 1492.
Maximum Idle Time This is the period of time required to keep the
connection alive if no packets are transmitted. I
no packets are transmitted between LAN port
and WAN port or between VDSL2 CO&CPE
MODEM and WAN, the connection is
disconnected after the 'Maximum idle time.
If the Auto-reconnect check box is selected, the
PPP connection is re-established if there is
some data that is received from the upper layers
to be transmitted on this link.
Click CANCEL to exit from this page without saving the changes.
Click APPLY to save the information that has been entered.
49
7.2.4.4 DNS
To configure the DNS address, click on the DNS link in the left navigation bar. A screen is displayed as shown in
Figure 7.2.4.4:
Figure 7.2.4.4 DNS Configuration
The screen contains the following details:
Fields in DNS
Field Description
Domain Name Server(DNS) Address Enter the DNS address of the primary DNS server.
Secondary DNS Address(optional) Enter the address of the secondary DNS server, if
available.
Click CANCEL to exit from this page without saving the changes.
Click APPLY to save the information that has been entered.
50
7.2.5 LAN
The LAN Setting can be viewed in the left navigation bar. The following are the options available under LAN, as shown in
Figure 7.2.5:
• LAN Settings
•
DHCP Client List
Figure 7.2.5 LAN in Left Navigator Bar
51
7.2.5.1 LAN Settings
Attention: For the VDSL2 CO&CPE MODEM it is recommended to select a simple IP setting suitable to controlled lab
environments. Set a static IP address and don’t use DHCP. The required steps are explained in Chapter 4.4
on Page 14!
To configure the LAN interface, click on the LAN Settings link in the left navigation bar. A screen is displayed as shown in
Figure 7.2.5.1 in case of the VDSL2 CO&CPE Modem.
Figure 7.2.5.1 LAN Settings
The screen contains the following details:
Fields in LAN Settings
Field
Description
IP Address Enter the LAN interface IP Address of VDSL2
CO&CPE MODEM.
Subnet Mask Enter the LAN Subnet Mask of VDSL2 CO&CPE
MODEM.
The Gateway acts as DHCP
Server
Enable or disables the DHCP Server of the VDSL2
CO&CPE MODEM. Select the check-box to enable
this option.
52
Click CANCEL to exit from this page without saving the changes.
Click APPLY to save the information that has been entered.
7.2.5.2 DHCP Client List
To view the DHCP client list, click on the DHCP Client List link in the left navigation bar. A screen is displayed to list all
DHCP client connection with IP Address and MAC Address as shown in Figure 7.2.5.2.
Figure 7.2.5.2 DHCP Client List
53
7.2.6 NAT
The NAT Settings can be viewed in the left navigation bar. The following are the options available under NAT, as shown in
Figure 7.2.6:
• Virtual Server
•
Port Mapping
•
DMZ
Figure 7.2.6 NAT in Left Navigator Bar
54
r
y
T
y
y
r
y
r
7.2.6.1 Virtual Server
To configure virtual server, click on the Virtual Server link in the left navigation bar. A screen is displayed as shown in
Figure 7.2.6.1:
Figure 7.2.6.1 Virtual Server Configuration
The screen contains the following details:
Fields in Virtual Server
Field
Description
Private IP Enter a private IPAddress of specified ent
Private Port Enter a private Port number of the specified entry.
pe Select virtual server protocol t
pe of the specified ent
Public Port Enter a public port number of the internet user to access
the virtual serve
.
Enabled Enable the specified entry of the virtual server.
Click CANCEL to exit from this page without saving the changes.
Click APPLY to save the information that has been entered.
55
.
.
A
7.2.6.2 Port Mapping
To configure Port Mapping, click on the Port Mapping link in the left navigation bar. A screen is displayed as shown in
Figure 7.2.6.2:
Figure 7.2.6.2 Port Mapping Configuration
The screen contains the following details:
Fields in Port Mapping
Field
Description
Server IP Enter the IPAddress of a specified local machine.
Mapping Port
Enabled Enable a specified entry of the Port Mapping.
Click CANCEL to exit from this page without saving the changes.
Click APPLY to save the information that has been entered.
ssign a range of port or specific port number to route the packets.
56
A
7.2.6.3 DMZ
To configure the DMZ, click on the DMZ link in the left navigation bar. A screen is displayed as shown in Figure 7.2.6.3:
Figure 7.2.6.3 DMZ Configuration
The screen contains the following details:
Fields in DMZ
Field Description
Enable Enable or disable the DMZ setting of VDSL2 CO&CPE
IP
ddress Enter IPAddress of the DMZ host.
MODEM. Select the check box to enable this option.
Click CANCEL to exit from this page without saving the changes.
Click APPLY to save the information that has been entered.
57
7.2.7 Firewall
The Firewall Settings can be viewed in the left navigation bar. The following are the options available under Firewall, as
shown in Figure 7.2.7:
• Firewall Options
•
MAC Control
•
Client Filter
Figure 7.2.7 Firewall in Left Navigator Bar
58
r
A
r
W
A
W
A
7.2.7.1 Firewall Options
To enable the firewall options, click on the Firewall Options link in the left navigation bar. A screen is displayed as shown
in Figure 7.2.7.1:
Figure 7.2.7.1 Firewall Options Configuration
The screen contains the following details:
Fields in Firewall Options
Field Description
Enable Hacke
Discard PING from
Discard PING the Gateway Select the check box to drop all PING to VDSL2 CO&CPE
Drop Port Scan Select the check box to drop all the port scan packets.
Click APPLY to save the information that has been entered.
ttack Protect Select the check box to log and drop all the hacke
N Select the check box to drop all PING from the
MODEM packet for the LAN side.
59
attack events.
N side.
A
7.2.7.2 MAC Control
To configure MAC Control, click on the MAC Control link in the left navigation bar. A screen is displayed as shown in
Figure 7.2.7.2:
Figure 7.2.7.2 MAC Control Configuration
The screen contains the following details:
Fields in MAC Control
Field Description
MAC
Block Connection to Internet Enable or disable block status. If the check box is
MAC Address Assign the blocking MAC address for local
Click Add to add the specified MAC address entry in the list.
ddress Control Enable or disable the MAC address control.
selected, it blocks the specified MAC address.
machine.
60
7.2.7.3 Client Filter
To enable Client Filter, click on the Client Filter link in the left navigation bar. A screen is displayed as shown in
Figure 7.2.7.3.
Figure 7.2.7.3 Client Filter Configuration
61
A
W
A
The screen contains the following details:
Fields in Client Filter
Field
Description
Enable Client Filter Enable or disable the Client Filter feature of VDSL2
CO&CPE MODEM. Select the check box to enable
this option.
IP Enter the filter IP Address range of the local
machines under VDSL2 CO&CPE MODEM.
Port Enter the filter Port number range of the local
machines under VDSL2 CO&CPE MODEM.
Type Select TCP or UDP to filter the protocol type
packets from the local machines.
Enable Provides more IP
ddresses of the
N interface.
Click CANCEL to exit from this page without saving the changes.
Click APPLY to save the information that has been entered.
62
7.2.8 Route Settings
The Route Settings can be viewed in the left navigation bar. The following are the options available under Route, as
shown in Figure 7.2.8:
• Static Routing
•
Routing Table List
Figure 7.2.8 Route in Left Navigator Bar
63
A
r
y
r
r
7.2.8.1 Static Routing
To setup Static Routing, click on the Static Routing link in the left navigation bar. A screen is displayed as shown in
Figure 7.2.8.1.
Figure 7.2.8.1 Static Routing Configuration
The screen contains the following details:
Fields in Static Routing
Field Description
Destination LAN IP Enter the IP
ddress of routing ent
.
Subnet Mask Enter the Subnet Mask of routing entry.
Gateway Ente
Click Add to add the information that has been entered.
the Gateway address of routing ent
64
y.
7.2.8.2 Routing Table List
To view the Routing entry table list of VDSL2 CO&CPE MODEM, click on the Routing Table by link in the left navigation
bar.
A screen is displayed as shown in Figure 7.2.8.2.
Figure 7.2.8.2 Routing Table List
The screen contains the following details:
Click Refresh to update currently routing list of the VDSL2 CO&CPE MODEM.
65
7.2.9 UPnP Settings
The UPnP Settings can be viewed in the left navigation bar. The following are the options available under UPnP, as
shown in Figure 7.2.8:
Settings
Figure 7.2.9 UPnP in Left Navigator Bar
66
7.2.9.1 Settings
To enable or disable the UPnP Settings, click on the Settings link in the left navigation bar. A screen is displayed as
shown in Figure 7.2.9.1.
Figure 7.2.9.1 UPnP Configuration
The screen contains the following details:
Table 22 Fields in UPnP Settings
Description
Field
Enable UpnP To enable or disable UPnP Setting. Select the check box to
Enable or Disable the UPnP function of VDSL2 CO&CPE
MODEM.
Click CANCEL to exit from this page without saving the changes.
Click APPLY at any time during configuration to save the information that you have entered.
67
Appendix A: Product Features & Specification
Product NameVDSL2 CO&CPE MODEM( VDSL2 Modem)
Features:
Compliant with IEEE 802.3 & 802.3u Ethernet Standards
Compliant with ETSI, ITU, ANSI VDSL standards
Provides 4 x 10/100M auto-sensing RJ-45 Ethernet ports
Supports Bandwidth setup with 100 Mbps VDSL RJ-11 ports
POTS / ISDN Splitter port RJ-11 x 1 (Splitter on board)
Supports auto speed for VDSL2 port
Supports Web management(HTTP)
Supports TFTP
Supports PPPOE
Supports uPnP
Supports NAT/DHCP/DMZ
Supports Firewall
Supports Route & Switch mode
Supports Loop back
Supports SNR indicator
Provides surge protection for VDSL2 port
Specifications:
Compliant with IEEE 802.3 & 802.3u Ethernet Standards
Compliant with ETSI, ITU, ANSI VDSL2 standards
10/100M auto-sensing/auto-MDIX RJ-45 Ethernet ports x 4
VDSL2 RJ-11 port x 1 (VDSL2 CO MODEM / VDSL2 CPE MODEM)
POTS / ISDN Splitter port RJ-11 x 1
Switch method : store and forward
Flow control Full duplex : IEEE 802.3x
68
Half duplex : Back pressure
Driver capable : 100 M: 0.3 Km
Indication LED x 6: Power LED x1
Ethernet Link/Active LED x 4
VDSL Link LED x 1
Console port : RS-232C/115200bps
Dimension: L x W x H = 184mm x 146mm x 40mm(7.2" x 5.74" x 1.57")
Operating temperature: 0°C to 50°C (32 to 122F)
Operating humidity: 10% to 90% (non-condensing)
Storage temperature: -20 to 65°C (-4F to 149F)
AC to DC adapter
Input range: 100VAC~240VAC/50~60Hz
Output: 12VDC/1A
Power consumption : 7.5w
EMI Compliant: CE, FCC, VCCI
Chipset: Infineon
69
Appendix BCompliance and Safety Information
FCC Radio Frequency Interference Statement
This equipment has been tested to comply with the limits for a computing device, pursuant to Part 15 of FCC rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment can generate, use and radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by taking one or more of the following
measures
1.Reorient or relocate the receiving antenna.
2.Increase the distance between the equipment and receiver.
3.The equipment and the receiver should be connected to outlets on separate circuits.
4.Consult the dealer or an experienced radio/television technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
If this telephone equipment causes harm to the telephone network, the telephone company will notify you in
advance that temporary discontinuance of service may be required. But if advance notice isn’t practical, the
telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a
complaint with the FCC if you believe it is necessary.
70
The telephone company may make changes in its facilities, equipment, operations or procedures that could affect
the proper functioning of your equipment. If they do, you will be notified in advance in order for you to make
necessary modifications to maintain uninterrupted service.
This equipment may not be used on coin service provided by the telephone company. Connection to party lines is
subject to state tariffs.
Important Safety Instructions
CautionThe direct plug-in wall transformer serves as the main product for disconnecting. The socket outlet shall be
installed near the product and be readily accessible.
CautionUse only the power supply included with this product. In the event the power supply is lost or damaged
In the United States, use only with CSA certified or UL listed Class 2 power supply, rated 12Vdc 1A or above.
IN Europe, use only with CE certified power supply, rated 12Vdc 1A or above.
Do not use this equipment near water, for example in a wet basement.
Avoid using a telephone during an electrical storm. There may be a remote risk of electrical shock from lightning.
Do not use the telephone to report a gas leak in the vicinity of the leaking area.
If you experience trouble with this unit, please contact customer service at the address and phone listed below. DO
NOT DISASSEMBLE THIS EQUIPMENT. It does not contain any user serviceable components.
FCC Warning
This equipment has been tested to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment can generate, use, and radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at owner’s expense.
71
CE Mark Warning
This is a CE class A product. In a domestic environment, this product may cause radio interference in which case
the user may be required to take adequate measures.
Warranty
The original owner of this package will be free from defects in material and workmanship for one-year parts after
purchase. For the warranty to apply, you must register your purchase by returning the registration card indicating
the date of purchase.
There will be a minimal charge to replace consumable components, such as fuses, power transformers, and
mechanical cooling devices. The warranty will not apply to any products which have been subjected to any misuse,
neglect or accidental damage, or which contain defects which are in any way attributable to improper installation or
to alteration or repairs made or performed by any person not under control of the original owner.
The above warranty is in lieu of any other warranty, whether express, implied, or statutory, including but not limited to
any warranty of merchantability, fitness for a particular purpose, or any warranty arising out of any proposal,
specification, or sample. Shall not be liable for incidental or consequential damages. We neither assumes nor
authorizes any person to assume for it any other liability.
Note: Please do not tear off or remove the warranty sticker as shown, otherwise the warranty will be void
72
.
Loading...