INSTALLATION & USER MANUAL
Auto Tracking / High Speed PTZ Camera
Thank You for Choosing Our PTZ Camera!
When you open the box:
Check that the packing and the contents are not visibly damaged. Contact the retailer immediately if any parts are
either missing or damaged.
Make sure if the contents are all included as per the packing list.
Do not attempt to use the device with missing or damaged parts. Send the product back in its original packing if it is
damaged.
The information contained in the document is subject to change without notice.
i / i
Table of Contents
1.
Safety Notes --- Important!!!.............................................................................................................................1
2. About The Product............................................................................................................................................2
2.1. Features.................................................................................................................................................. 2
2.2. Functions ................................................................................................................................................ 2
2.3. Technical Parameters ............................................................................................................................. 4
2.3.1.
2.3.2. HITACHI Modules ........................................................................................................................4
3. Installation..........................................................................................................................................................5
3.1. DIP Switch Setting .................................................................................................................................. 5
3.2. Installation............................................................................................................................................... 5
3.2.1.
3.2.2.
3.2.3.
3.2.4.
4. Operation Guide ..............................................................................................................................................12
4.1. Operation At Power Up ..........................................................................................................................12
4.2. How To Use Our Control Keyboard .......................................................................................................12
4.2.1.
4.2.2.
4.2.3.
4.3. Select A Camera....................................................................................................................................13
4.4. Camera Motions.....................................................................................................................................13
4.4.1.
4.4.2.
4.4.3. Focus .........................................................................................................................................14
4.4.4.
4.4.5.
4.5. Function Program Menu.........................................................................................................................15
4.5.1.
4.5.2. Display Setup .............................................................................................................................16
4.5.3.
4.5.4.
4.5.5.
4.6. Special Control Panel Commands .........................................................................................................34
5. Trouble Shooting.............................................................................................................................................35
6. Annex................................................................................................................................................................36
6.1. DIP Switch Chart....................................................................................................................................36
6.2. OSD Menu Diagram...............................................................................................................................41
SONY Modules.............................................................................................................................4
Wall Mount Installation .................................................................................................................5
In-ceiling Mount Installation..........................................................................................................7
Surface Mount Installation..........................................................................................................10
Pole Mount Installation ............................................................................................................... 11
Control Keypad Password And Access ...................................................................................... 12
Control Keypad Command Syntax .............................................................................................12
Control Keypad Command Types ..............................................................................................13
Pan And Tilt................................................................................................................................ 13
Zoom .......................................................................................................................................... 14
IRIS Opening.............................................................................................................................. 14
Preset Positions Programming and Recalling ............................................................................14
Product Information .................................................................................................................... 16
4.5.2.1.
4.5.3.1.
4.5.3.2.
4.5.3.3.
4.5.3.4.
4.5.3.5.
4.5.3.6.
4.5.3.7. Clear Set ...........................................................................................................................24
4.5.3.8.
4.5.4.1.
4.5.4.2.
4.5.4.3. Password ..........................................................................................................................27
4.5.4.4.
4.5.4.5.
4.5.4.6.
4.5.4.7.
Label Position....................................................................................................................17
Main Programming Menu (Dome Settings 1) .............................................................................17
Camera .............................................................................................................................18
Motion ...............................................................................................................................20
Power Up ..........................................................................................................................22
Presets..............................................................................................................................22
Patterns.............................................................................................................................23
Zones ................................................................................................................................24
Preset Number ..................................................................................................................25
Secondary Programming Menu (Dome Settings 2) .................................................................... 25
Alarm Submenu ................................................................................................................25
Addr setting.......................................................................................................................26
Windows Blanking.............................................................................................................28
Heater Setting ...................................................................................................................30
Cruise Setting....................................................................................................................31
Tracking Setting ................................................................................................................31
Dome Label................................................................................................................................33
ii / iii
1. SAFETY NOTES --- IMPORTANT!!!
The following important notes must be followed carefully to run the PTZ camera and respective accessories in total safety.
The camera and relative accessories are called video system
Use the instructions correctly and fully
Read all safety rules and instructions carefully before starting to run the video system.
Follow the instructions in the instruction manual. Pay attention to all warnings on the camera and in the instruction manual.
Keep the safety notes and instructions for future reference.
Attachments & Accessories
Do not use attachments other than those recommended in the instruction manual because this could cause risks to the
products. Only use the recommended accessories for the camera for installation and operation.
Protect the video system
To protect the camera, avoid installing and using it in direct sunlight or any source of bright light. Bright light, like that from
a spotlight, can cause dimming and blurs. A vertical line may appear on the screen. This does not indicate a problem.
Keep it away from rain and dust. Do not touch the zoom lens with your fingers. If needed, use a soft cloth and methylated
spirit to remove traces of dust. Apply a specific cap to protect the zoom lens when the camera is not in use.
Install the camera away from video interference. The pictures could present interference if the leads are arranged near a
TV set or other device. Either move the leads or re-install the device to solve the problem.
Do not use any part of the video system near water, i.e. bathtubs, wash basins, sinks, tubs, on damp surfaces, near
swimming pools, etc. Do not insert objects of any kind through the camera openings to avoid touch live parts: fire and
electrocution risk. Do not pour any kind of liquid on the device.
A switch for performing maintenance operations on the camera must be included. Connect the camera only to the
electrical power supply shown on the ratings plate. Contact your retailer if in doubt.
Lay the power wires keeping them from being trodden on or squeezed by objects placed on top of them. Pay particular
attention to leads near plugs, screws and the product outlet.
Disconnect the power lead and the wiring to protect the camera during electrical storms or when it is left unattended and
not used for a long time. This will prevent damage to the video system in the event of lightening or electrical line overload.
Do not overload the electrical power and the extensions to prevent the risk of fire or electrocution.
Do not place the camera near or over radiators or sources of heat. Check that the area is suitably ventilated before
installing the camera inside partially closed areas (such as recesses, bookshelves and shelves).
Do not position the camera on unsteady trolleys, stands, brackets or tables. The camera could fall and severely injury
adults and children in addition to seriously damaging the product.
Maintenance & Repairs
Always contact a qualified service technician to repair the camera (or any other part of the video system). Unauthorized
opening or removing the lids may cause fire and electrocution risk and other dangers.
Disconnect all electrical parts from the mains before cleaning.
Uses spare parts specified by the manufacturer or spare parts with equivalent characteristics when replacements
required. Unauthorized replacements can cause fires, electrical shocks and other dangers.
After any servicing intervention or repair to the video system, ask the technician to run a safety check to ensure that
everything is working safely.
Damage requiring professional assistance
Disconnect the video system from the power mains and call qualified service personnel in the following cases:
If the power lead or plug is damaged.
If liquid or foreign objects accidentally penetrate inside the device.
If the device was exposed to rain or water.
If the device was dropped, subjected to heavy shocks or if the camera packaging was damaged.
If the device performance changes considerably.
in this section.
1 / 1
2. ABOUT THE PRODUCT
The tracking PTZ is based on our unique motion tracking technology with high position resolution, high speed, low price
and selectable communication protocols. It is widely used in surveillance system as unattended CCTV device.
2.1. FEATURES
Auto tracking of moving object (auto PTZ) based on our motion tracking technology;
Max 36X optical, 0.01Lux of module specifications;
360º horizontal rotation at maximum speed of 240º /sec;
Auto cruise function with 256 preset positions;
Built-in OSD Menu, to change dome parameter, achieve auto scan, and pattern etc;
Features password protection to prevent unauthorized changes to the dome setting;
Windows blanking and tracking boundary for privacy purpose;
EasyClip installation features;
The feature of defining specific activity when the dome parks;
Auto-flip to follow object and surveillance of any subject that is constant and continuous;
The speed can be adjusted automatically according to zooming times;
Auto focus lens and auto white balance, BLC function;
Multi protocol compatible (Pelco-P, Pelco-D etc);
Alarm input, Alarm output, Alarm action.
2.2. FUNCTIONS
Object Tracking
In auto tracking mode, the camera can track a moving object in the target area with auto pan, tilt and zoom which realizes
smart unattended surveillance.
Tracking Cruise
The tracking function can be activated during cruise. At a preset of the cruise list, the camera can track moving objects
automatically.
Soft Address
The camera address can be programmed with built-in OSD menu, and the user does not need to dismount the camera
from field or do any screw work.
Wide Dynamic Range (WDR)
A camera is intended to provide clear images even under back light circumstances where intensity of illumination can vary
excessively, when there are both vary bright and vary dark areas simultaneously in the field of view. WDR enables the
capture and display of both bright areas and dark areas in the same frame, in a way that there are details in both areas,
i.e. bright areas are not saturated, and dark areas are not too dark.
Day/Night Function
The IR cut filter of camera module inside the camera can be removed by sending special command, so that the camera
can change from color to mono. The picture is clear even if the illumination is as low as 0.01Lux.
Wide Dynamic Range (WDR) and Day/Night function are based on the relative modules. Please refer to technical
parameters.
Proportional Pan
Proportional pan automatically reduces or increases the pan and tilt speeds in proportion to the zooming times. At
telephoto zoom settings, the pan and tilt speeds will be slower for a given amount of joystick deflection then at wide zoom
settings. This keeps the image from moving too fast on the monitor when there is a large amount of zoom.
Auto Flip
When the camera tilts downward and goes just beyond the vertical angle, the camera rotates 180º. When the camera
rotates (flips), the camera starts moving upward as you continue to hold joystick in the down position. Once you let go of
the joystick after the dome rotates, joystick control returns to normal operation. The auto-flip feature is useful for following
a person who passes directly beneath the camera.
Save/Call Preset
Preset function is that dome saves current horizontal angle and title angle of pan/tilt, zoom and position parameters into
2 / 2
memory. When necessary dome calls these parameters and adjusts Pan/Tilt and camera to that position. User can save
and call presets easily and promptly by using keyboard controller or infrared controller. The camera supports up to 256
presets.
Lens Control
1) Zoom control
User can adjust zoom wide or tele by controller and get desired image.
2) Focus control
System defaults Auto Focus mode, that is, the lens and camera will automatically adjust the focus to get the best image.
Focus can also be controlled manually from the controller if required. Press Focus Near or Focus Far key to manually
focus. Focus can be manual via keyboard or matrix, please refer to control keyboard or matrix operation manual for
detailed operation. When adjusting position is set with focus status, it goes back to auto focus.
The camera will NOT auto focus in the following status.
Target is not in the center of image.
Targets are in near and far at the same time.
Target is of strong light object. Such as spotlight etc.
Target is behind the glass with water drop or dust.
Target moves too fast.
Large area target such as wall.
Target is too dark or vague.
3) IRIS control
System defaults Auto IRIS. Camera can adjust immediately according to the alteration of back ground illumination so that
a lightness steady image can be achieved.
You may adjust IRIS by controller to get required image brightness, and call back Auto IRIS by controlling the joystick.
Auto White Balance
Camera can automatically adjust white balance (WB) according to the alteration of background lightness to give a true
color image.
Back Light Compensation (BLC)
If a bright backlight presents, the subjects in the picture may appear dark or as a silhouette. Backlight compensation
enhances objects in the center of the picture. The camera uses the center of the picture to adjust the IRIS. If there is a
bright light source outside this area, it will wash out to white. The camera will adjust the IRIS so that the object in the
sensitive area is properly exposed.
Auto Cruise
The preset position is programmed to be recalled in sequence. This feature is called auto cruise. Up to 30 presets can be
saved in each cruise tour.
Patterns
A pattern is a saved, repeating, series of pan, tilt, zoom and preset functions that can be recalled with a command from a
controller or automatically by a programmed function (alarm action or park action or power-up action).
Auto, Random and Frame Scan
Auto Scan: Make the camera scan 360º ranging from the current position.
Random Scan: Make the camera random scan 360º ranging from the current position.
Frame Scan: This feature freezes the scene on the monitor when going to a preset. This allows for smooth transition from
one preset scene to another.
Zones Setting
A zone is a pan area, defined by a left and right limit, on the 360º pan plane. The camera has eight zones, each with a
6-character label.
Alarms Input
The camera has four alarm inputs, which can be programmed as high, medium or low priority. When an alarm is received,
an input signal to the camera triggers the user-defined action (go to preset, run pattern, etc.) programmed for the alarm.
Auxiliary Output
An auxiliary output is a programmable signal from the camera back box that can trigger another device to operate. An
auxiliary output is programmable to trigger from an alarm or from a controller.
3 / 3
Password Protection
The camera features password protection to prevent unauthorized changes to the camera settings. You can open the
System Information and Display Setup Screens, but cannot access any of the camera Settings menus.
Windows Blanking
A set window can be saved so that it is the only blanked tilt area of the scene. All other parts of the tilt area of the scene
will be visible.
Windows blanking is only available for Sony Modules at present.
2.3. TECHNICAL PARAMETERS
2.3.1. SONY MODULES
Model FCB-EX45C (18X) FCB-EX480C (18X) FCB-EX980 (26X) FCB-EX1010 (36X)
Function Object auto tracking
Signal Format PAL/NTSC
Image Sensor ¼ inch color CCD
H. Resolution 480 TVL 530TVL
Video Out 1.0±0.2V
P/T Speed
S/N Ratio ≥50DB
AGC Auto/Manual
BLC Auto/Manual
Sensitivity 1Lux 0.01Lux
IR cut Filter No Yes
Wide Dynamic Range (WDR) No Yes
LENS F1.4-F3.0 f=4.1-73.8mm
Optical Zoom 18X 26X 36X
Digital Zoom 12X
Pan:0.05º～240º/sec;Tilt:0.03º～160º/sec
P-P
Table 1: Sony Modules
F1.6-F3.8
f=3.5-91mm
F 1.6-4.5
f=3.4-122.4mm
2.3.2. HITACHI MODULES
Model VK-S858 (23X) VK-S634 (30X) VK-S654 (35X)
Function Object auto tracking
Signal Format PAL/NTSC(selectable)
Image Sensor ¼ inch color CCD
H. Resolution 540TVL
Video Out 1.0±0.2V
P/T Speed
S/N Ratio ≥50DB
AGC Auto/Manual
BLC Auto/Manual
Sensitivity 0.01Lux 0.001Lux
IR cut Filter Yes
Wide Dynamic Range (WDR) Yes
LENS F1.6-F3.7 f=3.6-82.8mm
Optical Zoom 23X 30X 35X
Digital Zoom 8X
Pan:0.05º～240º/sec;Ttil:0.03º～160º/sec
P-P
F1.4- F4.6
f=3.4-102mm
Table 2: Hitachi Modules
F1.4- F4.2
f=3.4-119mm
The specifications are subject to change without notice.
4 / 4
3. INSTALLATION
This section contains detailed instructions for installing the camera. These instructions assume that the installer has a
good knowledge of installation techniques and is capable of adopting safe installation methods.
3.1. DIP SWITCH SETTING
Before installing the camera drive, check the DIP switches; configure the receiver address, communication protocol, and
baud rate setting. Pic. 1 shows switches position and default settings. SW1 switches (1bit) and SW2 switches (1, 2, and 7
bit) are set to the ON position. For normal user, setting switches to default position is enough.
Pic. 1 Switch Position
The camera can be controlled via various communication protocols by setting SW1 switches(1, 2, 3,and 4) and operate at
1200bps, 2400bps, 4800bps, 9600bps and 19200bps baud rate by setting SW1 switches(5, 6, 7, and 8). Refer to Table 3:
SWITCH1 SETTING for communication protocol and baud rate settings, do not set the switches to reserved position. Pic.
2 shows the default settings for the DIP switches.
Pic. 2 Default settings of DIP switches
Please refer to Table 29: SWITCH1 SETTING and Table 30: SWITCH2 SETTING in Section 6.1 to set baud rate, and
communication protocol type and camera address.
Always use the “PELCO P” or “PELCO D” protocols.
Do not use address “0” with the “PELCO P” or “PELCO D” protocols.
3.2. INSTALLATION
The camera has four types of mountings: wall mount, in-ceiling mount, surface mount, and pole mount. Please make sure
which type you are installing.
3.2.1. WALL MOUNT INSTALLATION (WITH POWER BOX)
Step 1. Install the power box on wall
Install the power box to the wall with 4 screws.
Pic. 3
5 / 5
When installing outdoors, make sure installation is properly sealed to keep moisture out.
To install the ptz camera with no power box, install the bracket directly onto the wall and then go to Pic 6.
Pic. 4
Pull the cables (of video, alarm, control etc.) through the cable hole of the power box and do necessary connections. The
cables are supplied by user.
Pic. 5
Refer to the instructions supplied with the bracket. Take out cables for the dome through the bracket. And install the
bracket to the power box. See Pic. 5
Pic. 6
Press the thumb fastener and open the hinged door to the back box. Take out hole of pin. Screw the metal cover into the
bracket. See Pic. 6.
Pic. 7
Connect cables to hole of pin. Insert the pin inside the back box. When finished, close the door to the back box and turn
on the power. The LED will light up. See Pic. 7.
If the LED does not light up, refer to Section 5: Trouble Shooting.
Step 2. Install dome drive
6 / 6
Pic. 8
Set the DIP switches for SW1 and SW2 at the bottom of the dome drive for the appropriate receiver address,
communication protocol, and baud rate. Refer to the labels on the dome drive or DIP SWITCH SET at the beginning of
this manual.
Remove cover of camera and sponge. See Pic. 8.
Pic. 9
Line up link card and faucet of the back board of the dome. Push the dome drive in. See Pic. 9.
Step 3. Install lower dome.
Pic. 10
Take out a screw from lower dome. Link cables, screw, and lower dome. See Pic. 10.
Pic. 11
Line up the mounting screw holes, and install the two mounting screws. Push the lower dome inside the back box. See
Pic. 11.
Pic. 12
Screw the two mounting screws, and screws in the bracket. See Pic. 12.
3.2.2. IN-CEILING MOUNT INSTALLATION
7 / 7
Step 1. Prepare In-ceiling
Pic. 13
Locate the center point of the in-ceiling mounting location. Insert the compass tool into the hole. Draw a circle on the
ceiling using the compass tool and a pencil. See Pic. 14 (Left).
Cut the circle out of the ceiling tile. See Pic. 14 (Right).
Pic. 14
Put the reinforcing metal plate (see following pic.) on top of the ceiling (behind the ceiling) with the two circles aligned
vertically.
Pic. 15
Step 2. Install back box
Take out bracket from back box. Insert the back box into ceiling. See Pic. 16.
Install a safety chain/cable (not supplied) that can stand up to 32 pounds (14.6kg). Press the thumb fastener and open the
hinged door to the back box. Take out hole of pin. See Pic. 17
Pic. 16
8 / 8
Pic. 17
Pull cables into the back box through the plastic panel. Connect cables to hole of pin. See Pic. 18
Pic. 18
Insert the hole of pin inside the back box. When finished, close the door to the back box and turn on the power. The LED
will light up. See Pic. 19.
Pic. 19
If the LED does not light up, refer to Section 5: Trouble Shooting.
Step 3. Install dome drive
Set the DIP switches for SW1 and SW2 at the bottom of the camera drive for the appropriate receiver address,
communication protocol, and baud rate. Refer to the labels on the camera drive or DIP SWITCH SET in this manual.
Remove cover of camera and sponge. See Pic. 20
Pic. 20
Line up link card and faucet of the back board of the dome. Push the dome drive in. See Pic. 21
Pic. 21
Step 4. Install lower dome
9 / 9
Pic. 22
Take out a screw from lower dome. Link cables, screw, and lower dome. See Pic. 22.
Pic. 23
Line up the snaps on trim ring with the mounting screws on the back box. Snap the trim ring into the plastic snap washers
on the mounting screws. See Pic. 23.
3.2.3. SURFACE MOUNT INSTALLATION
Step 1. Install back board of surface mount
Pic. 24
Locate the back board of the camera location. Drill a hole in the ceiling using a drill. Insert the screw and back board into
the hole. See Pic. 24
Pic. 25
Press the thumb fastener and open the hinged door to the back box. Take out hole of pin. See Pic. 26.
Pic. 26
Pull cables into the back box into the plastic panel. Connect cables to hole of pin. Insert the hole of pin inside the back
board. When finished, close the door to the back board and turn on the power. The LED will light up. See Pic. 26.
10 / 10
If the LED does not light up, refer to Section 5: Trouble Shooting.
Step 2. Install dome drive
Set the DIP switches for SW1 and SW2 on the bottom of the dome drive for the appropriate receiver address,
communication protocol, and baud rate. Refer to the labels on the dome drive or DIP SWITCH SET in this manual.
Pic. 27
Line up link card and faucet of the back board of the dome. Push the dome drive in. See Pic. 27.
Step 3. Install dome flange
Snip a flake piece. Keep three flanges away from two clamps on the back board. See Pic. 28.
Pic. 28
Pic. 29
Push the flange of dome into the back board. Take out the membrane on the clarty flake of the dome drive. See Pic. 29.
3.2.4. POLE MOUNT INSTALLATION
See Section 3.2.1
Wall Mount Installation.
11 / 11
4. OPERATION GUIDE
4.1. OPERATION AT POWER UP
The camera employs the default settings the first time it is switched on. Changes to the settings will be permanently
stored and will be made available the next time the camera is switched on. You can return to the default settings by
means of the appropriate menu option at any time.
The camera will work as follows when it is switched on.
The camera will run a calibration procedure and a message showing the following information will appear on the video
output OSD (On Screen Display): protocol, communication parameters, and camera address and software version.
PROTOCOL: PELCO-D
COM: 9600, N, 8, 1
ADDR: 1
SOFTWARE VERSION V4.3.3
Check that the data are suitable for operation. Otherwise, refer to the section in this document that shows how to install
the camera correctly.
At the end of the calibration step, the camera will switch to stand-by as programmed (POWER UP ACTION in DOME
SETTINGS1 > POWER UP). The camera will continue working this way until any command is received from the keypad.
The camera during this phase can be pointed to a fixed point or pan across the field. Refer to the detailed described in the
POWER UP ACTION menu section for more details.
4.2. HOW TO USE OUR CONTROL KEYBOARD
The camera is ready to receive commands from our control keyboard (see figure below) after connecting.
4.2.1. CONTROL KEYPAD PASSWORD AND ACCESS
The system will wait for the password to be entered after being switched on.
The control panel requires a 6-digit password.
The entered digits will be replaced by a “*” symbol on the screen for privacy.
Access to the menu is gained after entering all the digits correctly.
Refer to the corresponding manual for using the control panel.
The default user password is “000000”.
It is advisable to change the default password to prevent intrusions.
Do not lose or forget the programmed password.
Take note of the new password and keep it in a safe place.
4.2.2. CONTROL KEYPAD COMMAND SYNTAX
Controls can use the joystick, single keys or key combinations. The key command syntax is shown below.
Key command syntax
The syntax used in this manual for controls using keys consists of various elements (words and three digit numbers).
Each command is always in braces and each element is separated by commas. Each word or decimal digit used in the
syntax is identified by a corresponding key on our control panel. Words can be enclosed in round brackets, square
brackets or no brackets. Three digit decimals are never enclosed in brackets.
The following words only can be used: PRESET
, ENTER. The decimal digits are: 0, 1, 2, 3, 4, 5, 6, 7, 8, and 9.
SCAN
, CALL, ESC, OPEN, CLOSE, NEAR, FAR, ZOOM OUT, ZOOM IN, CAM, MON,
12 / 12
Some application examples of controls are shown in detail below.
Using the joystick
A command can also be given simply by moving the joystick because this generates actions on the camera or OSD (On
Screen Display) menu.
Using a single key
Pressing a single key can cause camera action. For example, the following command will zoom out of the frame.
Underling indicates the key is in use.
ZOOM OUT
Key combinations
Pressing a key combination in rapid sequence extents the command set. For example, the following command (select
camera address 1) is performed by pressing the following keys:
CAM
+ 1 + ENTER
4.2.3. CONTROL KEYPAD COMMAND TYPES
There are four command types:
Select camera,
Move camera (tilt and pan, zoom, adjust focus and IRIS opening, go to preset positions),
Adjust camera operation mode using menus,
Various quick controls operable from the control panel.
The method for accessing these controls will be shown in detail in the following paragraphs.
4.3. SELECT A CAMERA
The camera to be controlled must be selected first. For example, the following command selects camera 1:
+ 1 + ENTER
CAM
After this operation, the message CAM 1 will appear on the control panel display.
4.4. CAMERA MOTIONS
After selecting a camera, it can be moved either directly using the control panel as described below:
Panning (horizontal) and tilting (vertical).
Zooming, focusing and IRIS opening.
Preset positions programming and recalling.
These functions can be directly accessed using a single key or joystick or a simple key combination.
4.4.1. PAN AND TILT
The camera may be moved using our keyboard controller. Move the joystick vertically to tilt the camera and horizontally to
pan it.
The maximum pan span is from 0º to 360º with continuous rotation. The maximum tilt span is from -5º (camera in vertical
position) and 92º.
The panning and tilting speed can be modulated by operating the joystick appropriately.
Note that the maximum speed that can be obtained by operating the joystick is not always equal to that programmed in
the working settings. This in fact depends on the value of the PROPORTIONAL PAN setting in the MOTION menu and the
zoom. If the option is ON, the maximum rotation speed which can be obtained using the joystick is proportional to the
magnification used to obtain the best frame.
Panning (horizontal)
Tip the joystick rightwards to turn the camera horizontally clockwise and tip it leftwards to turn it anticlockwise.
If no advanced options are set (e.g. range limits set enabled), the camera can be turned continuously without
13 / 13
interruptions.
The pan span may be limited between two angles in SETTING1 > MOTION > MANUAL LIMIT.
Tilting (vertical)
Tip the joystick upwards to turn the camera vertically upwards and tip it downwards to turn the camera downwards. The
camera rotation is limited upwards by the horizontal plane or downwards by the vertical axis.
Performance will change considerably near the vertical axis according to whether the AUTO FLIP is on or not (default
setting is on).
With AUTO FLIP off, the camera will stop in perfectly vertical position and will stop turning when the joystick is tipped
downwards.
With AUTO FLIP on, the camera will proceed over the vertical axis when the joystick is tipped downwards. This is
because, when the vertical axis is reached, the camera flips automatically by 180 degrees and resumes the initial
trajectory.
The AUTO FLIP function can be used to follow a subject arriving in a certain direction passes under the camera and
continues in a straight line. To do this, hold the joystick tipped downwards following the movement of the subject. Observe
that in this case the joystick performance after the camera passes over the vertical axis opposite to the normal axis
because tipping the joystick downwards will turn the camera upwards.
Normal operation of the joystick will be resumed as soon as the downward tip is interrupted (also only for an instant). At
this point, to follow the subject in the same direction, you will need to tip the joystick upwards, as you would normally.
4.4.2. ZOOM
The camera frame may be adjusted by using the ZOOM IN
detail; use ZOOM OUT
Zoom can be set as per the zoom specifications of relative modules, combined between optical zoom and digital zoom.
Refer to the specific section for programming the function.
to zoom out.
and ZOOM OUT commands. Use ZOOM IN to zoom into the
4.4.3. FOCUS
The camera focus may be adjusted manually using the NEAR
As the auto focus function is always on, a manual setting made using NEAR and FAR will be kept only until a pan, tilt or
zoom command is used. In this case, auto focus will adjust focus automatically again.
Refer to the specific section for additional details on focusing and on the various options.
and FAR controls.
The auto focus function cannot work correctly in the following cases:
The object to be focused on is not in the middle of the image.
There are far and near objects in the frame.
Bright light is shining on the subject.
The subject is behind a glass pane covered in drops or dust.
The subject is moving very quickly.
The subject is not well lit.
The subject is too big.
4.4.4. IRIS OPENING
The IRIS opening may be controlled manually using the OPEN
The manual setting made using OPEN
automatic IRIS opening option is enabled (the default setting is on). In this case, the opening will be controlling
automatically again.
Refer to the specific section for additional details on IRIS opening adjustment
and CLOSE will be kept only until a pan, tilt or zoom command is used if the
4.4.5. PRESET POSITIONS PROGRAMMING AND RECALLING
and CLOSE commands.
14 / 14
The camera can store up to 256 panning, tilting and zooming configurations (called preset positions) which can be
recalled at any time. The manual focusing and IRIS opening settings cannot be stored.
When storing presets, it is important to remember that some are reserved and cannot be either stored or used fo r
positioning the camera.
Presets from 80 to 99, Presets from 100 to 103, 170 to 173
The following examples show how to program the free Presets and recall them.
Example: programming preset number 32
1) Position the camera in a certain pan, tilt and zoom configuration.
2) Enter the command PRESET
From this moment on, simply enter the command CALL + 32 + ENTER to move the camera to the preset position.
+ 32 + ENTER.
The saved value will be written over if the setting is reprogrammed.
The Presets are saved in a permanent memory area of the camera where they are maintain ed also when pow er
is disconnected. However, RESTORE FACTORY DEFAULT will delete all preset values.
Press PRESET + 83 + ENTER to delete all the saved presets.
The Presets store the coordinates according to an angular reference system. Therefore, the reference system
zero point may become misaligned with the camera mecha nics after prolonged use of the tilting and panning
functions. Minor inaccuracies in preset positions may occur. In this case, calibrate the angular coordinate system
using the REBOOT SYSTEM command. This calibration is automatically run when the camera is switched on.
4.5. FUNCTION PROGRAM MENU
Use the following control panel command to access the function programming menu.
PRESET
At this point, if no password is required for access, the following first level menu will appear on the screen:
+ 95 + ENTER
MAIN MENU
< SYSTEM INFORMATION >
< DISPLAY SETUP >
< DOME SETTINGS 1 >
< DOME SETTINGS 2 >
< DOME LABEL >
RESET CAMERA
REBOOT SYSTEM
LANGUAGE ENGLISH
EXIT
Screen 1: Main Menu
Otherwise, if a password is required, the following prompt will appear.
PLEASE INPUT PASSWORD
PASSWORD
1 2 3 4 5 6 7 8 9 0
▲
CLEAR
ENTER
EXIT
Screen 2: Password Protection
The password is a numeric combination (max. 4 digits).
Select the password digits by moving the joystick in the horizontal direction. Symbol “▲” indicates the digit which will be
entered.
Press OPEN
The entered numbers will be replaced by a “*” symbol on the screen for privacy.
to enter the selected digit.
15 / 15
Select ENTER
and press OPEN to access the first level menu after entering all the digits correctly.
The default password is “0000”.
It is advisable to change the default password to prevent intrusions.
Do not lose or forget the programmed password.
Take note of the new password and keep it in a safe place.
Simply move the joystick vertically to scroll the menu and point the cursor to the menu item to be selected: at this point,
select OPEN
Simply press BACK and use OPEN to go back to the previous level menu.
To completely exit a menu on any level, simply select EXIT and use the OPEN command.
Option Value Explanation
SYSTEM INFORMATION
DISPLAY SETUP
DOME SETTINGS 1
DOME SETTINGS 2
DOME LABEL
RESET CAMERA
REBOOT SYSTEM
LANGUAGE ENGLISH
4.5.1. PRODUCT INFORMATION
In the first level menu, select SYSTEM INFORMATION to display information concerning the protocol, the camera address,
the presetting number, the language of use and the measured temperature. The information in this menu cannot be
edited.
4.5.2. DISPLAY SETUP
The DISPLAY SETUP menu is used to enable the labels to be displayed for the various camera functions.
to access the selected second level.
COM 2400,N,8,1
ADDRESS 1
PROTOCOL PELCO-D
PRESETS 256
LANGUAGE ENGLISH
TEMPERATURE 36°C
SOFTWARE VERSION V4.3.3
BACK
EXIT
Screen 3: System Info
PRESET LABEL ON
ZONE LABEL ON
ZOOM ON
P/T DEG ON
DOME LABEL ON
<LABEL POSITION>
TEMPERATURE OFF
BACK
EXIT
Screen 4: Display Menu
Product information menu (refer to Section 4.5.1).
Display menu (refer to Section 4.5.2).
Main programming menu (refer to Section 4.5.3).
Secondary programming menu (refer to Section 4.5.4).
Menu for associating the text to be associated to the camera (refer
Section 4.5.5).
This function reset the device without clearing the settings
performed by the user. Resets the camera menu settings, except
for the password.
This function restarts the device without clearing the settings
performed by the user. The camera is repositioned.
Menus in English.
Table 3
SYSTEM INFORMATION
DISPLAY SETUP
16 / 16
Option Value Explanation
PRESET LABEL ON/OFF
ZONE LABEL ON/OFF
ZOOM ON/OFF
P/T DEG ON/OFF
DOME LABEL ON/OFF
LABEL POSITION
TEMPERATURE ON/FF
4.5.2.1. LABEL POSITION
The labels may be positioned where required on the screen.
To establish a position:
1) Point the cursor to the label to be moved by moving the joystick vertically.
2) Press OPEN
3) Symbol “■” will appear.
4) Position the entire label in the chosen position using the joystick.
5) Press OPEN
6) Repeat this operation for each label.
7) Point the cursor “►” to SAVE and press OPEN
.
Show or hide presetting labels (max. 64).
Show or hide zone labels.
Show or hide zoom labels.
Show or hide camera pan/tilt labels. The coordinates refer to the
monitor centre.
Show or hide dome labels.
Label positioning submenu (refer to Section 4.5.2.1)
Show or high the camera temperature.
Table 4
ZONE DOME PRESET
SAVE
RESET
P/T DEG ZOOM
Screen 5: Label Position
.
4.5.3. MAIN PROGRAMMING MENU (DOME SETTINGS 1)
In the first level menu, select <DOME SETTINGS 1> and the corresponding submenus to access the main menus.
<CAMERA>
<MOTION>
<POWER UP>
<PRESETS>
<PATTERNS>
<ZONES>
<CLEAR SET>
TOTAL PRESETS NUMBER 256
BACK
EXIT
DOME SETTINGS1
Screen 6: Dome Settings 1
Option Value Explanation
CAMERA
MOTION
POWER UP
PRESETS
PATTERNS
ZONES
CLEAR SET
TOTAL PRESET NUMBER 40/64/256
Camera parameter programming submenu (refer to Section
4.5.3.1)
Camera motion parameter programming submenu (refer to Section
4.5.3.2)
Power up parameter submenu (refer to Section 4.5.3.3)
Preset parameter submenu (refer to Section 4.5.3.4)
Pattern parameter submenu (refer to Section 4.5.3.5)
Zone parameter programming submenu (refer to Section 4.5.3.6)
Clear settings submenu (refer to Section 4.5.3.7)
Maximum number of Presets. Always enter 256 (refer to Section
17 / 17
4.5.3.8)
Table 5
4.5.3.1. CAMERA
The first level of this menu contains the following options grouped as shown in the following table.
To edit the value, simply select the required menu item using the joystick with vertical movements and the OPEN
Then edit as required. Select BACK/EXIT to close the item.
CAMERA
DIGITAL ZOOM OFF
BACKLIGHT COMP OFF
<PROGRAM AE MODE>
<ADDITIONAL>
WIDE DYNAMIC RANGE OFF
BACK
EXIT
Screen 7: Camera (Sub-Menu)
Option Value Explanation
button.
DIGITAL ZOOM ON/OFF
BACK LIGHT COMP ON/OFF
PROGRAM AE MODE
ADDITIONAL
WIDE DYNAMIC RANGE ON/OFF
PROGRAM AE CONTROL submenu - Automatic Exposure settings
Option Value Explanation
Switch digital zoom ON or OFF.
Switch back light compensation ON and OFF. The BACK LIGHT
COMPENSATION function is useful for improving visibility when the
background light is very bright.
Automatic exposure submenu (see below)
Additional settings submenu (see below).
Activate WDR feature of the camera. This is only available on related
optical modules.
Table 6
PROGRAM AE CONTROL
AE MODE AUTO
LOW LIGHT MODE AUTO
LOW LIGHT LIMIT 1/50
IRIS LEVEL F2.0
AGC LEVEL 0DB
BRIGHT LEVEL 0DB/F2.0
SPOT AE OFF
BACK
EXIT
Screen 8: Program AE Control
In this mode:
- The shutter opening time cannot be set and is
AE MODE
AUTO
automatically adjusted.
- Auto IRIS opening is automatically adjusted.
- Gain control is automatic (AGC ON).
In this mode:
- The shutter opening time may be varied as programmed
SHUTTER
in the “LOW LIGHT LIMIT” menu.
- Auto IRIS opening is automatically adjusted.
- Gain control is automatic (AGC ON).
18 / 17
In this mode:
- The IRIS opening time is fixed to 1/50 second.
IRIS
- The auto IRIS opening is manually varied in the “IRIS
LEVEL” menu.
- Gain control is automatic (AGC ON).
In this mode:
- The shutter opening time may be varied as programmed
in the “LOW LIGHT LIMIT” menu.
MANUAL
- The auto IRIS opening is manually varied in the “IRIS
LEVEL” menu.
- AGC gain control is variable as programmed in the “AGC
LEVEL” menu. All items may be accessed in this mode.
In this mode:
- The IRIS opening time is fixed to 1/50 second.
BRIGHT
- The auto IRIS opening is manually varied in the “BRIGHT
LEVEL” menu.
- Gain control is off (0 dB).
This parameter is as follows:
- AUTO: uses a fixed maximum IRIS opening (1/50 second).
- MANUAL: increases camera sensitivity to the detriment of
LOW LIGHT MODE AUTO/MANUAL
1/2, 1/3, 1/6, 1/12,
1/25, 1/50, 1/75,
1/100, 1/120, 1/150,
LOW LIGHT LIMIT
IRIS LEVEL
AGC LEVEL
BRIGHT LEVEL 0DB ~ 28DB
SPOT AE ON/OFF
1/215, 1/300, 1/425,
1/600, 1/1000,
1/1250, 1/1750,
1/2500, 1/3500,
1/6000, 1/10000 OF
SECOND
F2.0, F1.6, F1.4,
OFF, F22, F19, F16,
F14, F11, F 9.6,
F8.0, F6.8, F5.6,
F4.8, F4.0, F3.4,
F2.8, F2.4
-3DB, 0DB, 2 DB, 4 DB,
6DB, 8 DB, 10 DB, 12
DB, 14 DB, 16 DB, 18
DB, 20 DB, 22 DB, 24
DB, 26 DB, 28 DB
refreshing frequency (frame rate) using the “LOW LIGHT
LIMIT” value.
These adjustments are possible only in “MANUAL” or
“SHUTTER” mode.
This selects the maximum opening of the IRIS. It is used to
manually set the IRIS opening time.
These adjustments are possible only in “MANUAL” or
“SHUTTER” mode.
Manual IRIS adjustment (parameter F).
It is used to manually set the IRIS opening time.
These adjustments are possible only in “MANUAL” or “IRIS”
mode.
It is possible to automatically control gain (AGC) to one of the
indicated values.
This selection is used to manually set the video signal gain.
These adjustments are possible only in “MANUAL” mode.
This function adjusts the camera gain and the IRIS opening
using a special algorithm which may be programmed by the
user. Exposure is controlled by the gain in low light condition
and by the IRIS opening in bright light conditions.
The function may be used only if “AE MODE” is set to
BRIGHT”.
“
If this function is on, the adjustments only use the middle part
of the image.
Table 7
The following items cannot be accessed in if “AE MODE” is set to “AUTO”:
LOW LIGHT MODE (fixed to “MANUAL”)
LOW LIGHT LIMIT
IRIS LEVEL
AGC LEVEL
BRIGHT LEVEL
ADDITIONAL sub-menu - Other program settings.
19 / 19
IR SW MODE AUTO
IR STATUS COLOR
AUTO IRIS ON
SHARPNESS ON
SHARPNESS LEVEL 5
AUTO WHITE BALANCE AUTO
R GAIN 214
B GAIN 164
BACK
EXIT
ADDITIONAL
Screen 9: Additional Sub-Menu
Option Value Explanation
The opening and closing of the IR filter which adjusts the
Day & Night vision of the camera may be controlled in
IR SW MODE AUTO/MANUAL
IR STATUS COLOR, B/W
AUTO IRIS ON/OFF
SHARPNESS ON/OFF
SHARPNESS LEVEL 0 ~ 15
ATW
AUTO
AUTO WHITE BALANCE
OUT
IN
MAN
R GAIN 0 ~ 255
MANUAL mode. The MANUAL option enables the possibility
to adjust the IR STATUS parameter (color, B/W). In AUTO
mode, the switch is automatic according to the lighting.
Day & Night camera configuration.
The auto IRIS may operate automatically (ON) or at a
predetermined level in the “IRIS LEVEL” menu. If
enabled manually, this function will remain operative until
the camera performs an angular movement of less than
15 degrees. It will switch automatically.
The sharpness of the image may be adjusted
automatically (ON) or to a level defined in the
“SHARPNESS LEVEL” menu.
Sharpness can be programmed in the range from 1 to 15
(15 corresponds to maximum sharpness).
White Balance (WB) is performed in auto tracking mode
(Auto Tracking White). This mode automatically
balances the white level by analyzing a wide range of
colors, i.e. all those with temperatures comprised in the
range between 2000K and 10000K.
This mode automatically adjusts the white balance by
analyzing a more restricted range with respect to the
previous option i.e. those with temperatures in the range
from 3000K and 7500K.
This function automatically balances the whites for
outdoor use.
This function automatically balances the whites for indoor
use.
In this mode, white balancing may be performed by
manually selecting the amount of red (R GAIN) and blue
(B GAIN).
Adjust the red components using these values.
B GAIN 0 ~ 255
4.5.3.2. MOTION
Adjust the blue components using these values.
Table 8
20 / 20
AUTO FLIP ON
PROPORTIONAL PAN ON
PARK TIME 15S
PARK ACTION NONE
SCAN SPEED<DEG/S> 1
<SET SCAN>
<MANUAL LIMIT>
<SET AZIMUTH ZERO>
<CLEAR AZIMUTH ZERO>
BACK
EXIT
Screen 10: Motion Sub-Menu
Option Value Explanation
AUTO FLIP ON/OFF
PROPORTIONAL PAN ON/OFF
PARK TIME 15 S ~ 12 H
NONE
AUTO SCAN
MOTION
When this option is on, the movements of a subject moving
underneath the camera can be followed by moving the
joystick vertically only. This is possible because after
reaching vertical position, the camera will automatically pan
by 180 degrees to be repositioned and resume the tilt stroke.
If this mode is active, the pan and tilt speed applied by the
keypad is proportional to the set zoom so that the movement
speed decreases when the zoom increases.
With this function, the camera will resume the function defined
in ”PARK ACTION” by specifying a value (in 1s, 1m, 1h steps)
following a stop or interruption of the performed function after
the programmed time.
No action is performed at the end of the park time.
The camera performs an auto scan at the end of the park
time: the camera performs a 360 horizontal scan operation.
RANDOM SCAN
FRAME SCAN
PRESET 1/PRESET 8
PARK ACTION
SCAN SPEED <DEG/S> 1 ~ 32 DEG./S
SET SCAN
MANUAL LIMIT ON/OFF
SET AZIMUTH ZERO
PATTERN 1 ~ 4
CRUISE
REPEAT LAST
HOME N TRA
CRUISE TRA
The camera performs a random scan at the end of the park
time: the camera performs a random 360 degree scan
pausing for approximately 2” every 142°.
The camera performs a frame scan at the end of the park
time: the horizontal scan is performed in the
The camera goes to preset 1 or preset 8 at the end of the park
time.
The camera performs one of the 4 patterns at the end of the
park time (command sequence continuously performed).
The camera performs a cruise (preset sequence) at the end of
the park time: the camera runs a cycle of up to 30 preset
positions.
The camera simply resumes the operation it was performing
before being interrupted at the end of the park time.
The camera goes to preset 1 and starts tracking at the end of
the park time.
The camera performs a cruise with tracking on at the end of
park time.
This will specify the rotation speed for automatic horizontal
scans.
This submenu set the limits for horizontal pan movements of
the camera. The limits are long applicable in FRAME SCAN
mode (see below).
If this option is ON, horizontal automatically scanning is
performed within the right and left scanning limits open.
To set the left and right scanning limit, position the camera at
the required pan angle and press OPEN
A preset position may be called up outside these scanning
limits.
This sets the pan zero position (see below).
SET SCAN limits.
to set.
21 / 21
CLEAR AZIMUTH ZERO
SET SCAN submenu
This includes a number of settings related to the programming of horizontal FRAME SCAN limits.
1) Press “►” on “SET SCAN STOPS”.
2) Press OPEN to confirm.
3) Go to the required position with the joystick to set the left scanning limit.
4) Press OPEN to confirm.
5) Go to the required position with the joystick to set the right scanning limit.
6) Press OPEN to confirm, Press CLOSE to cancel the operation.
7) Point the cursor “►” to “CLEAR SCAN STOPS” and press OPEN
SET AZIMUTH ZERO submenu
This includes the settings related to programming of the pan zero position.
1) Go to the required position with the joystick to set zero position.
2) Press OPEN
CLEAR AZIMUTH ZERO submenu
This includes the settings related to deleting the pan zero position.
1) Press OPEN to confirm.
2) Press CLOSE
4.5.3.3. POWER UP
Option Value Explanation
POWER UP ACTION
4.5.3.4. PRESETS
to confirm; Press CLOSE to cancel the operation.
to cancel the operation.
POWER UP ACTION NONE
BACK
EXIT
Screen 11: Power UP Sub-Menu
NONE
AUTO SCAN
RANDOM SCAN
FRAME SCAN
PRESET 1/ PRESET 8
PATTERN 1 ~ 4
CRUISE
HOME N TRA
CRUISE TRA
This is used to delete the zero settings (see below).
Table 9
to delete the programmed positions.
POWER UP
No action is performed at the end of power up.
The camera performs an auto scan at the end of power up: the
camera performs a 360 horizontal scan operation.
The camera performs a random scan at the end of power up:
the camera performs a random 360° scan pausing for
approximately 2” every 142°.
The camera performs a frame scan at the end of power up:
the horizontal scan is performed in the SET SCAN limits.
The camera goes to preset 1 or 8 at the end of power up.
The camera performs one of the 4 patterns at the end of
power up.
The camera performs a cruise at the end of power up: the
camera runs a cycle consisting of up to 30 preset positions.
The camera goes to preset 1 and starts tracking at the end of
power up.
The camera performs a cruise with tracking on at the end of
power up.
Table 10
The camera will start a scanning cycle when a presetting or pattern is recalled. This scanning cycl e may be
interrupted simply by moving the joystick.
22 / 22
PRESET NUMBER 1
…PRESET NOT DEFINED…
<EDIT PRESET LABEL>
<EDIT PRESET POSITION>
<CLEAR CURRENT PRESET>
BACK
EXIT
Option Value Explanation
PRESET NUMBER 1-64
EDIT PRESET LABEL
EDIT PRESET POSITION
CLEAR CURRENT PRESET
EDIT PRESET LABEL submenu
This includes the operations needed for associating a label to a presetting.
1) Use the joystick to point the cursor to ”EDIT PRESET LABEL” option.
2) Press OPEN
3) Point the cursor to the first character to the use and press OPEN
4) After writing the text, point the cursor to OK and press OPEN
4.5.3.5. PATTERNS
. The following menu will appear on the display:
PRESET NUMBER 1
PRESET LABEL 1 - - - - -
0 1 2 3 4 5 6 7 8 9 Y Z y z
A B C D E F G H I J K L M N O P Q R S T U V W X
a b c d e f g h I j k l m n o p q r s t u v w x
OK CANCEL
SPACE BACKSPACE`
Screen 13: Preset Label Sub-Menu
PATTERN NUMBER 1
<PROGRAM PATTERN>
<CLEAR CURRENT PATTERN>
BACK
EXIT
PRESETS
Screen 12: Presets
This option is used to select a presetting for entering a
descriptive label. This operation is allowed for up to 64
Presets.
Press the OPEN
of the presetting to the stored. Press OPEN
This submenu is used to access writing mode for associating
a label to a presetting (see below).
This submenu is used to position and save the current
position.
The submenu is used to delete the current prest.
Table 11
PATTERNS
button and use the joystick to set the number
. Point the cursor to “BACKSPACE” to delete it.
to save and go back to the main screen.
to confirm.
Screen 14: Patterns Sub-Menu
A pattern is a sequence of movements and functions which may be stored and repeated manually or automatically.
Option Value Explanation
PATTERN NUMBER 1 ~ 4
PROGRAM PATTERN
CLEAR CURRENT PATTERN
PROGRAM PATTERN submenu
This includes all the operations needed to program a pattern.
This option is used to select a pattern.
This submenu is used to program a pattern (see below)
This submenu is used to delete current pattern.
Table 12
23 / 23
1) Use the joystick to point the cursor to the ”PATTERN NUMBER” option.
2) Select the required pattern and press OPEN
3) Position the cursor under ”PROGRAM PATTERN” option and press the OPEN
The number of actions available (including zoom operations) for programming the Pattern is shown in percentage form on
the screen while they are each being programmed. 100 operations are available for each pattern.
4.5.3.6. ZONES
ZONE NUMBER 1
…ZONE NOT DEFINED…
<EDIT ZONE LABEL>
<EDIT ZONE>
ENABLE ZONE ON
<CLEAR CURRENT ZONE >
BACK
EXIT
A zone is a space defined on the display by the user. It may be associated to a label. Up to 8 zones may be defined.
Option Value Explanation
ZONE NUMBER 1 ~ 8
EDIT ZONE LABEL
EDIT ZONE
ENABLE ZONE ON/OFF
CLEAR CURRENT ZONE
EDIT ZONE LABEL submenu
This includes the operations needed to enter labels to be associated to zones.
1) Use the joystick to point the cursor to the ”EDIT ZONE LABEL” option.
2) Press OPEN
3) Point the cursor to the first character to be used and press OPEN
4) After writing the text, point the cursor to OK and press OPEN
EDIT ZONE submenu
This includes all the operations needed to program a zone.
1) Press “►” on “EDIT ZONE”.
2) Press OPEN
3) Use the joystick to point to the required position to define the left limit of the zone to be created.
4) Press OPEN to confirm. Press CLOSE to cancel the operation.
5) Use the joystick to point to the required position to define the right limit of the zone to be created.
6) Press OPEN to confirm. Press CLOSE to cancel the operation.
7) Press CLOSE
4.5.3.7. CLEAR SET
. The following menu will appear on the display:
to confirm.
to cancel the operation.
ZONE LABEL 1 - - - - 0 1 2 3 4 5 6 7 8 9 Y Z y z
A B C D E F G H I J K L M N O P Q R S T U V W X
a b c d e f g h I j k l m n o p q r s t u v w x
OK CANCEL
SPACE BACKSPACE
Screen 16: Zone Label Sub-Menu
.
ZONES
Screen 15: ZONES Sub-Menu
This option is used to select a zone.
Press the OPEN
zone number. Press OPEN
This submenu is used to associate a label to a zone (see
below).
This submenu is used to create a zone (see below).
This is used to enable/disable each zone selected in the
“ZONE NUMBER” field.
This submenu is used to delete the zone selected in the “ZONE
NUMBER” field (see below).
Table 13
ZONE NUMBER 1
button and use the joystick to set the required
. Point the cursor to “BACKSPACE” to delete it.
to save and go back to the main screen.
button.
to confirm.
24 / 24
CLEAR SET
CLEAR ZONES
CLEAR PRESETS
CLEAR PATTERNS
RESTORE FACTORY DEFAULT
BACK
EXIT
Screen 17: Clear Set Sub-Menu
This menu is used to delete the settings of several elements at one time.
Option Value Explanation
CLEAR ZONES
CLEAR PRESETS
CLEAR PATTERNS
RESTORE FACTORY
DEFAULT
4.5.3.8. PRESET NUMBER
This option can be used to set the number of Presets which may be used.
1) Point the cursor to “►” “PRESET NUMBER”.
2) Press ENTER.
3) Move the joystick vertically and select “256”.
4) Press ENTER to confirm.
This option is used to delete all the zone settings.
This is used to delete all the Presets.
This is used to delete all the pattern settings.
This performs a total reset and loads the default settings. The
operations may take a few seconds (approximately 20
seconds): the message “WAIT” will appear on the monitor.
Table 14
Do not change the setting (“256”).
4.5.4. SECONDARY PROGRAMMING MENU (DOME SETTINGS 2)
In the first level menu, select <DOME SETTINGS 2> and the corresponding submenus to access the other menus.
<ALARMS>
<ADDR SETTING>
<PASSWORD>
<WINDOWS BLANKING>
<HEATER SETTING>
<CRUISE SETTING>
<TRACKING SETTING>
BACK
EXIT
Option Value Explanation
ALARMS
ADDR SETTING
PASSWORD
WINDOWS BLANKING
HEATER SETTING
CRUISE SETTING
TRACKING SETTING
4.5.4.1. ALARMS
The camera has 4 alarm inputs and 2 alarm outputs. The actions defined by the user may be associated to an alarm.
DOME SETTINGS 2
Screen 18: Dome Settings 2
Alarm submenu (refer to Section 4.5.4.1)
Address setting submenu (refer to Section 4.5.4.2)
Password submenu (refer to Section 4.5.4.3)
Windows blanking submenu (refer to Section 4.5.4.4)
Heater use submenu (refer to Section 4.5.4.5)
Cruise programming submenu (refer to Section 4.5.4.6)
Automatic tracking submenu (refer to Section 4.5.4.7)
Table 15
25 / 25
ALARM NUMBER 1
SEQUENCE(SECS) 1
ALARM ACT CRUISE
ACTIVATE AUX OFF
<CLEAR SET>
DWELL TIME<SECS>1 0
DWELL TIME<SECS>2 0
BACK
EXIT
Screen 19: Alarms Sub-Menu
Option Value Explanation
ALARM NUMBER 1 ~ 4
SEQUENCE (SECS) 1 ~ 250
NONE
AUTO SCAN
RANDOM SCAN
FRAME SCAN
PRESET
ALARM ACT
ACTIVATE AUX
CLEAR SETTINGS
PATTERN 1
PATTERN 2
PATTERN 3
PATTERN 4
CRUISE
TRACKING
PRESET N TRA
CRUISE TRA
OFF
1
2
ALARMS
This option allows selecting one of the 4 alarm inputs.
Duration time (in seconds) of the action related to each alarm
when several alarms occur at the same time.
No action is performed on alarm.
The camera performs an auto scan on alarm: the camera
performs a 360 horizontal scan operation.
The camera performs a random scan on alarm: the camera
performs a random 360° scan pausing for approximately 2” every
142°.
The camera performs a frame scan on alarm: the horizontal scan
is performed in the SET SCAN limits.
The camera goes to related preset on alarm.
The camera performs pattern action 1 on alarm.
The camera performs pattern action 2 on alarm.
The camera performs pattern action 3 on alarm.
The camera performs pattern action 4 on alarm.
The camera performs a cruise on alarm: the camera runs a cycle
consisting of up to 30 preset positions.
The camera performs tracking action on alarm.
The camera goes to related preset and starts tracking function.
The camera performs a cruise with tracking on alarm.
No action occurs after the alarm.
Output 1 is on.
Output 2 is on.
This submenu is used to delete the alarm programming (see
below).
DWELL TIME<SECS>1 0 ~ 255
DWELL TIME<SECS>2 0 ~ 255
The duration of related alarm output
The duration of related alarm output
Table 16
If an alarm is triggered during any automatic operation of the camera (Pattern, Auto Tracking, etc.), the operation
in progress is stopped and the camera executes the action that has been set in the ALARM ACT
In the event of Preset action, the camera moves to the preset position. Then, if the option PARK ACTION is
set to execute an action, the action will be executed after the PARK TIME period has expired.
In the event of "TRACKING" action, the camera executes the tracking function starting from the preset
position that has been associated with the alarm. Once the tracking action has finished, the camera
executes the action set in the option PARK ACTION.
In the event of "PATTERN, AUTO SCAN, RANDOM SCAN, FRAME SCAN, CRUISE" actions, the action is
executed by the camera permanently and can only be stopped by one of the following actions: any
command sent by a controller or any alarm event.
4.5.4.2. ADDR SETTING
26 / 26
menu:
The soft address is the address programmed by built-in software. The hard address is the address programmed by the
hardware SWITCH 2.
ADDR TYPE HARD
ADDR SOFT 255
ADDR HARD 0
BACK
EXIT
ADDR SETTING
Screen 20: Alarm Settings
Option Value Explanation
This option is used to program the type of address in current
ADDR TYPE SOFT, HARD
ADDR SOFT 0~255
ADDR HARD
application.
Press the OPEN
Press OPEN
The option is used to change the soft address.
This option shows the hard address number. It is the address
of the SW2 (Switch Setting 2).
Table 17
button and use the joystick to select the value.
to confirm.
The camera needs a reboot for the new address to take effect. W hen the hard address is different from that of
last power up, the hard address will be applicable and the camera address will be hard type.
4.5.4.3. PASSWORD
ENABLE PASSWORD OFF
<EDIT PASSWORD>
BACK
EXIT
Screen 21: Password Sub-Menu
Option Value Explanation
PASSWORD
ENABLE PASSWORD ON/OFF
EDIT PASSWORD
The password is a numeric combination (max. 10 digits).
This enables the password.
This is the password entry procedure.
Table 18
The default password is “0000”.
It is advisable to change the default password to prevent intrusions.
Do not lose or forget the programmed password.
Take note of the new password and keep it in a safe place.
PASSWORD
1 2 3 4 5 6 7 8 9 0
CLEAR
ENTER
BACK
1) Select the password digits by moving the joystick in the horizontal direction. Symbol “▲” indicates the digit which will
be entered.
2) Press OPEN
3) The entered numbers will be replaced by a “*” symbol on the screen for privacy.
to enter the selected digit.
INPUT OLD PASSWORD
Screen 22: Edit Password
27 / 27
4) Enter all the digits correctly and select ENTER
5) During the password change procedure you will be asked to enter the old password. Enter the new password and
enter it again for confirmation.
4.5.4.4. WINDOWS BLANKING
to confirm.
Windows blanking is only available for Sony Modules at present.
The camera can be used to define up to eight privacy zones which blank out certain areas of the screen concealing them
from the operator’s sight.
A privacy zone appears as a grey or black rectangle associated to a certain pan, tilt and zoom position of a camera. This
association is used to move, expand and compress the rectangle according to how the pan, tilt or zoom settings are
changed.
STYLE GRAY
BLANK ALL ABOVE OFF
BLANK ALL BELOW OFF
<SET WINDOWS>
SET MASK COLOR 4
BACK
EXIT
Option Value Explanation
WINDOWS BLANKING
Screen 23: Windows Blanking
There are two ways to blank out the zone to be masked: either
STYLE GRAY/SMEAR
BLANK ALL ABOVE OFF, 0~80
BLANK ALL BELOW OFF, 0~80
SET WINDOWS
SET MASK COLOR 0 ~ 13
using a grey window which entirely conceals the area or by
using a semi-transparent smear window which shows the scene
without details.
Blanks out the upper part of the frame shown on the monitor.
The value means the beginning degree of the vertical position.
Blanks out the lower part of the frame shown on the monitor. The
value means the beginning degree of the vertical position.
The submenu is used to position and configure the privacy
zones (see below).
This is used to select the blanking window color:
0 → black
1 ~ 6 → grey (1 dark; 6 light)
7 → white
8 → red
9 → green
10 → blue
11 → cyan
12 → yellow
13 → magenta
Table 19
The two blanking bands (upper & lower) may coexist at the same time.
The two blanking bands (upper & lower) cannot coexist at the same time in presence of a privacy zone.
A band will automatically be removed if both bands are enabled and a priv acy zone is activated.
If an attempt to activate a blanking band is attempted with a privacy zone active, the privacy zone will remain
active to the detriment of the blank.
Blanking parameters
BLANK ALL ABOVE BLANK ALL BELOW
OFF No blanking OFF No blanking
0 -5º~10º 0 5º~92º
10 -5º~25º 10 -5º~92º
28 / 28
20 -5º~35º 20 5º~92º
30 -5º~45º 30 15º~92º
40 -5º~55º 40 25º~92º
50 -5º~65º 50 35º~92º
60 -5º~75º 60 45º~92º
70 -5º~85º 70 55º~92º
80 -5º~95º 80 70º~92º
Table 20
The coordinates shown on the monitor refer to the central point of the monitor (where the diagonals meet).
SET WINDOWS submenu
This includes the operations needed to position and configure the privacy zones.
WINDOWS NUMBER 1
<EDIT WINDOW LOCATION>
<EDIT WINDOW ZOOM >
ENABLE WINDOW OFF
CLEAR CURRENT WINDOW
BACK
EXIT
SET WINDOWS
Screen 24: Set Windows Sub-Menu
Option Value Explanation
WINDOWS NUMBER 1~ 8
EDIT WINDOW LOCATION
EDIT WINDOW ZOOM
ENABLE WINDOW ON/OFF
CLEAR CURRENT WINDOW
EDIT WINDOW LOCATION submenu
This menu may be used to define the position of the privacy zones to be created.
1) Press “►” on “EDIT WINDOW LOCATION”.
2) Press OPEN
3) A cross-shaped pointer will appear on the monitor: this pointer will correspond to the middle of the privacy zones
being created.
4) Point the cross-shaped cursor to the required position by moving the joystick in the vertical and horizontal directions.
5) Press OPEN
6) Use the joystick to obtain the required dimensions of the privacy zone:
a) move leftwards to increase the left and right edges of the blanking zone
b) move rightwards to decrease the left and right edges of the blanking zone
c) move upwards to increase the upper and lower edges of the blanking zone
d) move downwards to decrease the upper and lower edges of the blanking zone
7) Press OPEN
8) At this point, either select a new privacy zone or select CLOSE
. The following screen will appear.
. A square will appear on the monitor (with the previously defined features).
to confirm after reaching the required dimensions.
IRIS OPEN TO CONTINUE
IRIS CLOSE TO CANCEL
Screen 25: Edit Window Location Sub-Menu
This option is used to select one of the 8 privacy zones
(WINDOWS).
This option is used to activate the privacy zone positioning
procedure (see below).
This option sets the zoom level over which the created privacy
zone will be visible.
This switches the privacy zone selected in WINDOW NUMBER on
and off.
This deletes the privacy zone selected in WINDOW NUMBER.
Table 21
EDIT WINDOW LOCATION
to quit the menu.
29 / 29
It is preferable to set the privacy zones with a zoom level of 1x.
Remarks on Privacy Zones
Privacy zones can be programmed (and therefore the menu can be opened) in optical zoom
situations only. The privacy zone works also in digital zoom conditions.
The privacy zone rectangle will move on the screen when panning and tilting. Zooming will expand
and contract the rectangle.
The rectangle will expand twice in the vertical direction and four times in the horizontal position to
avoid viewing protected areas when panning, tilting and zooming.
After panning and tilting, the privacy zone rectangle will shift and return to the correct dimensions.
After zooming, the rectangle will remain either contracted or expanded according to the applied zoom
(regardless of the x2 or x4 factor applied while zooming).
It is advisable to make the privacy areas slightly larger than the area to be concealed.
Privacy zones can only be rectangular or squares, but several rectangles can be placed to mask the
area as required.
EDIT WINDOW ZOOM submenu
This menu item is used to define the zoom level at which the privacy zone becomes visible after defining the color and the
position of the privacy zone.
1) Press “►” on “EDIT WINDOW ZOOM”.
2) Press OPEN
3) Press OPEN
4) Use the joystick to obtain the required zoom level over which the privacy zone will become visible:
a) Turn clockwise to increase the zoom level
b) Turn anticlockwise to decrease the zoom level
5) Press OPEN to confirm.
4.5.4.5. HEATER SETTING
Option Value Explanation
, the following screen will appear.
EDIT WINDOW ZOOM
IRIS OPEN TO CONTINUE
IRIS CLOSE TO CANCEL
Screen 26: Edit Window Zoom
and start the zoom setting procedure. The newly created privacy zone will appear on the monitor.
HEATER SETTING
HEATER DISPLAY ON
HEATER MODE AUTO
TEMPERATURE SET 33℃
BACK
EXIT
Screen 27: Heater Setting
HEATER DISPLAY ON/OFF
AUTO
HEATER MODE
OFF
ON
TEMPERATURE SET -99 ~ +99
This switches the heater status display on and off. The
message “HEATER” will appear when the heater is on.
Heater operating mode: when set to ”AUTO”, the heater is
operated when the outside temperature is lower than the
setting made in the following menu.
The heater is always off.
The heater is always on.
Temperature threshold in °C under which the heater is
activated. Recommended values 18 - 20 °C
Table 22
30 / 30
4.5.4.6. CRUISE SETTING
CRUISE
DWELL TIME<SECS> 7
PRESET LIST 1
1 ON 0 OFF
1234567890 <PRESET 1-10>
0110010111
BACK
EXIT
Screen 28: Cruise
The CRUISE function is used to make the camera run a cycle consisting of up to 30 preset positions.
This menu item is used to enable each of the preset positions used in the cruise cycle.
For the cruise cycle to be effective, the preset positions must be actually stored.
Option Value Explanation
DWELL TIME <SECS> 5 ~ 250
PRESET LIST 1 ~ 3
4.5.4.7. TRACKING SETTING
DEFAULT SETTING
SIZE SENS MEDIUM
GRAY SENS MEDIUM
LOST ACT STOP TRACK
ZOOM SETTING ON
WAIT TIME<S> 40
<TRACKING BOUNDARY>
AUX OFF
TRACKING SPEED AUTO
TRACKING TIME<M> AUTO
BACK
EXIT
Screen 29: Tracking Setting Sub-Menu
The auto tracking function is used to automatically track moving objects by detecting grayscale variations in the frame.
Option Value Explanation
DEFAULT SETTING
SIZE SENS LARGE/MEDIUM/SMALL
GRAY SENS HIGH/MEDIUM/LOW
LOST ACT
HOME N TRA
KEEP TRACK
Duration (in seconds) of the dwelling time on each presetting.
Value 1 selects the first group of Presets from 1 to 10, value 2
selects the second group from 11 to 20, value 3 the third
group from 21 to 30.
The following 10 digits (1/10) are used to switch the
corresponding preset in the corresponding ten (1-10, 11-20,
21-30) either on or off (1=ON; 0=OFF).
Table 23
TRACKING SETTING
This function is used to load the auto tracking default
settings.
This option defines the total dimensions of the object to be
tracked. The parameters are LARGE/MEDIUM/SMALL. An
object larger than one fourth of the screen is LARGE. An
object smaller than one eighth of the screen is SMALL.
This option determines the auto tracking sensitivity. The
sensitivity measures the grey scale variations of a certain
point in the frame in the unit of time.
This option is used to establish the action to be performed
if the camera loses the tracked object: the HOME N TRA
option goes to preset 1 and starts tracking.
The KEEP TRACK option keeps the camera in the position
reached and the tracking function is kept on waiting for an
object to be intercepted again.
31 / 31
STOP TRACK
ZOOM SETTING OFF, 1 ~ 18
WAIT TIME
TRACKING BOUNDARY UP/DOWN/LEFT/RIGHT
AUX OFF, 1, 2
TRACKING SPEED AUTO, 1 ~ 63
TRACKING TIME
TRACKING BOUNDARY submenu
Operations needed to establish an intervention zone for the tracking function.
Option Value Explanation
BOUNDARY LIMIT ON/OFF
CLEAR BOUNDARY
LEFT LIMIT ON/OFF
RIGHT LIMIT ON/OFF
UP LIMIT ON/OFF
DOWN LIMIT ON/OFF
5, 10, 15, 20, 25,
30, 35, 40 SECONDS
AUTO,1~15
(MINUTES)
TRACKING BOUNDARY
BOUNDARY LIMIT OFF
CLEAR BOUNDARY
LEFT LIMIT OFF
RIGHT LIMIT OFF
UP LIMIT OFF
DOWN LIMIT OFF
BACK
EXIT
Screen 30: Tracking Boundary Sub-Menu
The STOP TRACK option leaves the camera in the position
reached and deactivates the tracking function.
This option determines the maximum zoom value that the
camera may use for tracking the object.
This option determines the time which must elapse before
performing LOST ACT.
This option is used to define the zone in which the camera
performs the tracking.
This option is used to activate one of the 2 alarm outputs if
the tracking function is on (OFF = no active alarm output).
This option establishes the camera movement speed. If
AUTO is selected, the camera is automatically “adapted” to
the motion of the target. The 1~63 options allow selecting
the expected speed of the object to be tracked (1 slow, 63
fast).
This option allows setting the max. tracking duration, in
minutes, during which the camera automatically tracks
moving objects.
Once the tracking time has expired, the camera exits the
tracking mode, waiting for further commands
Table 24
This switches tracking function intervention zone on and off.
This deletes the intervention area.
Left limit of the intervention zone.
Right limit of the intervention zone.
Up limit of the intervention zone.
Low limit of the intervention zone.
Table 25
Tracking during Cruise is now available to all models of tracking pt z. When the camera is cruising among saved
presets, it will detect and follow moving object automatically when it stops at a specific preset. W hen the moving
object gets out of view for pre-defined interval, the camera will go back to its previously stopped preset and cruise
to the next preset again.
Enter DOME SETTINGS 1 > MOTION > PARK ACTION, set it as REPEAT LAST
Go to DOME SETTINGS 2 > TRACKING SETTING > LOST ACT, set it as STOP TRACK
Go to DOME SETTINGS 2 > CRUISE > DWELL TIME, set it as 8 and program the preset list
PRESET
+ 92 + ENTER to start the function.
32 / 32
Advice for Correct Auto Tracking Use
General warnings
The tracking function should mainly be used in indoor environments.
Provide the best lighting possible in the detection zone: in poor lighting conditions, the inevitable
presence of noise on the image makes grayscale variations extremely critical. In poor lighting
conditions, the camera may easily loose the tracked object.
If IR illuminators are used, remember that:
The camera must be programmed to operate in B/W only (SETTINGS 1/CAMERA/ADDITIONAL
menu) because the Slow Shutter will make tracking unreliable in color mode
The lighting entirely covers the frame where motion is tracked, possibly by restricting the range of
action of the camera in tracking mode (using the TRACKING BOUNDARY option).
Avoid background objects in the frame which could trick the motion detector, such as for example
Venetian blinds, gates, doors with grid and objects with very marked, contrasting contours. A
chequerboard background is certainly the worst condition for satisfactory operation.
Do not use the privacy zone function in frames where auto tracking is used: the privacy zone can trick
the auto tracking function.
Do not use the auto tracking function if the object to be tracked and/or monitored moves too fast.
Recommended control parameters
SIZE SENS: select SMALL particularly in poor lighting conditions to improve performance.
GRAY SENS: most false alarms are caused by the tracking of unexpected objects. For this reason, it is
preferable to select low sensitivity.
ZOOM SETTING: it is advisable to use the lowest possible zoom values. Excessive detail makes tracking
difficult (the movement must be fastener and consequently or the risk of loosing the object is much higher).
WAIT TIME: particularly, in the case of poor lighting conditions or frames with interference, it is preferable to
set the lowest possible time to prevent the camera from constantly tracking unexpected objects (e.g. “video
noise” in the frame).
TRACKING SPEED: the AUTO setting should always be preferred, unless the object to be tracked does not
always move at low, constant speed.
TRACKING BOUNDARY: it is strong advised to delimit the tracking zone, avoiding including unnecessary
parts in the frame.
4.5.5. DOME LABEL
<EDIT DOME LABEL>
<CLEAR DOME LABEL>
BACK
EXIT
Screen 31: Dome Label Menu
Option Value Explanation
EDIT DOME LABEL
CLEAR DOME LABEL
EDIT DOME LABEL submenu
The operations needed to associate a label to a camera are:
1) Use the joystick to point the cursor to the ”EDIT DOME LABEL” option.
2) Press OPEN
. The following menu will appear on the display:
DOME LABEL
This submenu is used to access writing mode for associating
a camera label (see below).
This submenu allows deleting the label associated to the
camera (see below).
Table 26
33 / 33
DOME LABEL
0 1 2 3 4 5 6 7 8 9 Y Z y z
A B C D E F G H I J K L M N O P Q R S T U V W X
a b c d e f g h I j k l m n o p q r s t u v w x
OK CANCEL
SPACE BACKSPACE
3) Point the cursor to the first character to be used and press OPEN. Point the cursor to “BACKSPACE” to delete it.
4) After writing the text, point the cursor to OK and press OPEN
EDIT DOME LABEL
Screen 32: Edit Dome Label
to save and go back to the main screen.
4.6. SPECIAL CONTROL PANEL COMMANDS
The camera can be programmed and operated using various quick control panel commands.
Control panel command Function
PRESET + 95 + ENTER
PRESET + XXX + ENTER
CALL + XXX + ENTER
CALL + 80 + ENTER
CALL + 82 + ENTER
CALL + 83 + ENTER
PRESET + 84 + ENTER
PRESET + 85 + ENTER
PRESET + 86 + ENTER
PRESET + 87 + ENTER
CALL + 84 + ENTER
CALL + 85 + ENTER
CALL + 86 + ENTER
CALL + 87 + ENTER
CALL + 88 + ENTER
CALL + 89 + ENTER
CALL + 92 + ENTER
CALL + 93 + ENTER
CALL + 94 + ENTER
CALL + 97 + ENTER
CALL + 98 + ENTER
CALL + 99 + ENTER
Access main menu
Store preset position (Preset) xxx.
Recall preset position (Preset) xxx.
Start the tracking function
Start the cruise function
Delete all Presets
Store pattern 1
Store pattern 2
Store pattern 3
Store pattern 4
Start pattern 1
Start pattern 2
Start pattern 3
Start pattern 4
Start park action function
Stop park action function
Start cruise with tracking function activated
Call the menu of boundary setting
Start/Stop wide dynamic range function
Start random scan function
Start frame scan function
Start auto scan function
Table 27
When storing Presets, it is important to remember that some are reserved and cannot be either stored or used for
positioning the camera.
Presets from 80 to 99, Presets from 100 to 103, 170 to 173.
34 / 34
5. TROUBLE SHOOTING
Problem Possib le Reason Solution
Wrong wire connections Check and reconnect wires
Power on normally but no video
signal
Pan/Tilt not initializing when
power on
Video is not stable
Control center is not stable RS485 wiring error Check and reconnect the RS485
Wrong or bad power source Change power source
Fuse broken. Change fuse
Power cable is disconnected Reconnect power wiring
Address, protocol, and baud rate is not
correctly set
RS485 cable is not correctly connected Check and reconnect RS485 cable
Video cable is wrong Check and reconnect video
Power source is wrong Change the power source
Table 28
Check and set the parameters
again.
35 / 35
6. ANNEX
6.1. DIP SWITCH CHART
POS 1 2 3 4 DESCRIPTION
COMM
PTOL
POS DESCRIPTION 5 6 7 8
BAUD
RATE
(BPS)
Address 1 2 3 4 5 6 7 8
0 OFF OFF OFF OFF OFF OFF OFF OFF
1 ON OFF OFF OFF OFF OFF OFF OFF
2 OFF ON OFF OFF OFF OFF OFF OFF
3 ON ON OFF OFF OFF OFF OFF OFF
4 OFF OFF ON OFF OFF OFF OFF OFF
5 ON OFF ON OFF OFF OFF OFF OFF
6 OFF ON ON OFF OFF OFF OFF OFF
7 ON ON ON OFF OFF OFF OFF OFF
8 OFF OFF OFF ON OFF OFF OFF OFF
9 ON OFF OFF ON OFF OFF OFF OFF
10 OFF ON OFF ON OFF OFF OFF OFF
11 ON ON OFF ON OFF OFF OFF OFF
12 OFF OFF ON ON OFF OFF OFF OFF
13 ON OFF ON ON OFF OFF OFF OFF
14 OFF ON ON ON OFF OFF OFF OFF
15 ON ON ON ON OFF OFF OFF OFF
16 OFF OFF OFF OFF ON OFF OFF OFF
17 ON OFF OFF OFF ON OFF OFF OFF
18 OFF ON OFF OFF ON OFF OFF OFF
19 ON ON OFF OFF ON OFF OFF OFF
20 OFF OFF ON OFF ON OFF OFF OFF
21 ON OFF ON OFF ON OFF OFF OFF
22 OFF ON ON OFF ON OFF OFF OFF
23 ON ON ON OFF ON OFF OFF OFF
24 OFF OFF OFF ON ON OFF OFF OFF
25 ON OFF OFF ON ON OFF OFF OFF
26 OFF ON OFF ON ON OFF OFF OFF
27 ON ON OFF ON ON OFF OFF OFF
28 OFF OFF ON ON ON OFF OFF OFF
29 ON OFF ON ON ON OFF OFF OFF
30 OFF ON ON ON ON OFF OFF OFF
31 ON ON ON ON ON OFF OFF OFF
32 OFF OFF OFF OFF OFF ON OFF OFF
ON OFF OFF OFF USER
OFF ON OFF OFF PELCO-P
ON ON OFF OFF PELCO-D
OFF OFF ON OFF DAHUA
1200 ON OFF OFF OFF
2400 OFF ON OFF OFF
4800 ON ON OFF OFF
9600 OFF OFF ON OFF
19200 ON OFF ON OFF
Reserved for future use …
Table 29: SWITCH1 SETTING
36 / 36
33 ON OFF OFF OFF OFF ON OFF OFF
34 OFF ON OFF OFF OFF ON OFF OFF
35 ON ON OFF OFF OFF ON OFF OFF
36 OFF OFF ON OFF OFF ON OFF OFF
37 ON OFF ON OFF OFF ON OFF OFF
38 OFF ON ON OFF OFF ON OFF OFF
39 ON ON ON OFF OFF ON OFF OFF
40 OFF OFF OFF ON OFF ON OFF OFF
41 ON OFF OFF ON OFF ON OFF OFF
42 OFF ON OFF ON OFF ON OFF OFF
43 ON ON OFF ON OFF ON OFF OFF
44 OFF OFF ON ON OFF ON OFF OFF
45 ON OFF ON ON OFF ON OFF OFF
46 OFF ON ON ON OFF ON OFF OFF
47 ON ON ON ON OFF ON OFF OFF
48 OFF OFF OFF OFF ON ON OFF OFF
49 ON OFF OFF OFF ON ON OFF OFF
50 OFF ON OFF OFF ON ON OFF OFF
51 ON ON OFF OFF ON ON OFF OFF
52 OFF OFF ON OFF ON ON OFF OFF
53 ON OFF ON OFF ON ON OFF OFF
54 OFF ON ON OFF ON ON OFF OFF
55 ON ON ON OFF ON ON OFF OFF
56 OFF OFF OFF ON ON ON OFF OFF
57 ON OFF OFF ON ON ON OFF OFF
58 OFF ON OFF ON ON ON OFF OFF
59 ON ON OFF ON ON ON OFF OFF
60 OFF OFF ON ON ON ON OFF OFF
61 ON OFF ON ON ON ON OFF OFF
62 OFF ON ON ON ON ON OFF OFF
63 ON ON ON ON ON ON OFF OFF
64 OFF OFF OFF OFF OFF OFF ON OFF
65 ON OFF OFF OFF OFF OFF ON OFF
66 OFF ON OFF OFF OFF OFF ON OFF
67 ON ON OFF OFF OFF OFF ON OFF
68 OFF OFF ON OFF OFF OFF ON OFF
69 ON OFF ON OFF OFF OFF ON OFF
70 OFF ON ON OFF OFF OFF ON OFF
71 ON ON ON OFF OFF OFF ON OFF
72 OFF OFF OFF ON OFF OFF ON OFF
73 ON OFF OFF ON OFF OFF ON OFF
74 OFF ON OFF ON OFF OFF ON OFF
75 ON ON OFF ON OFF OFF ON OFF
76 OFF OFF ON ON OFF OFF ON OFF
77 ON OFF ON ON OFF OFF ON OFF
78 OFF ON ON ON OFF OFF ON OFF
79 ON ON ON ON OFF OFF ON OFF
80 OFF OFF OFF OFF ON OFF ON OFF
81 ON OFF OFF OFF ON OFF ON OFF
82 OFF ON OFF OFF ON OFF ON OFF
83 ON ON OFF OFF ON OFF ON OFF
37 / 37
84 OFF OFF ON OFF ON OFF ON OFF
85 ON OFF ON OFF ON OFF ON OFF
86 OFF ON ON OFF ON OFF ON OFF
87 ON ON ON OFF ON OFF ON OFF
88 OFF OFF OFF ON ON OFF ON OFF
89 ON OFF OFF ON ON OFF ON OFF
90 OFF ON OFF ON ON OFF ON OFF
91 ON ON OFF ON ON OFF ON OFF
92 OFF OFF ON ON ON OFF ON OFF
93 ON OFF ON ON ON OFF ON OFF
94 OFF ON ON ON ON OFF ON OFF
95 ON ON ON ON ON OFF ON OFF
96 OFF OFF OFF OFF OFF ON ON OFF
97 ON OFF OFF OFF OFF ON ON OFF
98 OFF ON OFF OFF OFF ON ON OFF
99 ON ON OFF OFF OFF ON ON OFF
100 OFF OFF ON OFF OFF ON ON OFF
101 ON OFF ON OFF OFF ON ON OFF
102 OFF ON ON OFF OFF ON ON OFF
103 ON ON ON OFF OFF ON ON OFF
104 OFF OFF OFF ON OFF ON ON OFF
105 ON OFF OFF ON OFF ON ON OFF
106 OFF ON OFF ON OFF ON ON OFF
107 ON ON OFF ON OFF ON ON OFF
108 OFF OFF ON ON OFF ON ON OFF
109 ON OFF ON ON OFF ON ON OFF
110 OFF ON ON ON OFF ON ON OFF
111 ON ON ON ON OFF ON ON OFF
112 OFF OFF OFF OFF ON ON ON OFF
113 ON OFF OFF OFF ON ON ON OFF
114 OFF ON OFF OFF ON ON ON OFF
115 ON ON OFF OFF ON ON ON OFF
116 OFF OFF ON OFF ON ON ON OFF
117 ON OFF ON OFF ON ON ON OFF
118 OFF ON ON OFF ON ON ON OFF
119 ON ON ON OFF ON ON ON OFF
120 OFF OFF OFF ON ON ON ON OFF
121 ON OFF OFF ON ON ON ON OFF
122 OFF ON OFF ON ON ON ON OFF
123 ON ON OFF ON ON ON ON OFF
124 OFF OFF ON ON ON ON ON OFF
125 ON OFF ON ON ON ON ON OFF
126 OFF ON ON ON ON ON ON OFF
127 ON ON ON ON ON ON ON OFF
128 OFF OFF OFF OFF OFF OFF OFF ON
129 ON OFF OFF OFF OFF OFF OFF ON
130 OFF ON OFF OFF OFF OFF OFF ON
131 ON ON OFF OFF OFF OFF OFF ON
132 OFF OFF ON OFF OFF OFF OFF ON
133 ON OFF ON OFF OFF OFF OFF ON
134 OFF ON ON OFF OFF OFF OFF ON
38 / 38
135 ON ON ON OFF OFF OFF OFF ON
136 OFF OFF OFF ON OFF OFF OFF ON
137 ON OFF OFF ON OFF OFF OFF ON
138 OFF ON OFF ON OFF OFF OFF ON
139 ON ON OFF ON OFF OFF OFF ON
140 OFF OFF ON ON OFF OFF OFF ON
141 ON OFF ON ON OFF OFF OFF ON
142 OFF ON ON ON OFF OFF OFF ON
143 ON ON ON ON OFF OFF OFF ON
144 OFF OFF OFF OFF ON OFF OFF ON
145 ON OFF OFF OFF ON OFF OFF ON
146 OFF ON OFF OFF ON OFF OFF ON
147 ON ON OFF OFF ON OFF OFF ON
148 OFF OFF ON OFF ON OFF OFF ON
149 ON OFF ON OFF ON OFF OFF ON
150 OFF ON ON OFF ON OFF OFF ON
151 ON ON ON OFF ON OFF OFF ON
152 OFF OFF OFF ON ON OFF OFF ON
153 ON OFF OFF ON ON OFF OFF ON
154 OFF ON OFF ON ON OFF OFF ON
155 ON ON OFF ON ON OFF OFF ON
156 OFF OFF ON ON ON OFF OFF ON
157 ON OFF ON ON ON OFF OFF ON
158 OFF ON ON ON ON OFF OFF ON
159 ON ON ON ON ON OFF OFF ON
160 OFF OFF OFF OFF OFF ON OFF ON
161 ON OFF OFF OFF OFF ON OFF ON
162 OFF ON OFF OFF OFF ON OFF ON
163 ON ON OFF OFF OFF ON OFF ON
164 OFF OFF ON OFF OFF ON OFF ON
165 ON OFF ON OFF OFF ON OFF ON
166 OFF ON ON OFF OFF ON OFF ON
167 ON ON ON OFF OFF ON OFF ON
168 OFF OFF OFF ON OFF ON OFF ON
169 ON OFF OFF ON OFF ON OFF ON
170 OFF ON OFF ON OFF ON OFF ON
171 ON ON OFF ON OFF ON OFF ON
172 OFF OFF ON ON OFF ON OFF ON
173 ON OFF ON ON OFF ON OFF ON
174 OFF ON ON ON OFF ON OFF ON
175 ON ON ON ON OFF ON OFF ON
176 OFF OFF OFF OFF ON ON OFF ON
177 ON OFF OFF OFF ON ON OFF ON
178 OFF ON OFF OFF ON ON OFF ON
179 ON ON OFF OFF ON ON OFF ON
180 OFF OFF ON OFF ON ON OFF ON
181 ON OFF ON OFF ON ON OFF ON
182 OFF ON ON OFF ON ON OFF ON
183 ON ON ON OFF ON ON OFF ON
184 OFF OFF OFF ON ON ON OFF ON
185 ON OFF OFF ON ON ON OFF ON
39 / 39
186 OFF ON OFF ON ON ON OFF ON
187 ON ON OFF ON ON ON OFF ON
188 OFF OFF ON ON ON ON OFF ON
189 ON OFF ON ON ON ON OFF ON
190 OFF ON ON ON ON ON OFF ON
191 ON ON ON ON ON ON OFF ON
192 OFF OFF OFF OFF OFF OFF ON ON
193 ON OFF OFF OFF OFF OFF ON ON
194 OFF ON OFF OFF OFF OFF ON ON
195 ON ON OFF OFF OFF OFF ON ON
196 OFF OFF ON OFF OFF OFF ON ON
197 ON OFF ON OFF OFF OFF ON ON
198 OFF ON ON OFF OFF OFF ON ON
199 ON ON ON OFF OFF OFF ON ON
200 OFF OFF OFF ON OFF OFF ON ON
201 ON OFF OFF ON OFF OFF ON ON
202 OFF ON OFF ON OFF OFF ON ON
203 ON ON OFF ON OFF OFF ON ON
204 OFF OFF ON ON OFF OFF ON ON
205 ON OFF ON ON OFF OFF ON ON
206 OFF ON ON ON OFF OFF ON ON
207 ON ON ON ON OFF OFF ON ON
208 OFF OFF OFF OFF ON OFF ON ON
209 ON OFF OFF OFF ON OFF ON ON
210 OFF ON OFF OFF ON OFF ON ON
211 ON ON OFF OFF ON OFF ON ON
212 OFF OFF ON OFF ON OFF ON ON
213 ON OFF ON OFF ON OFF ON ON
214 OFF ON ON OFF ON OFF ON ON
215 ON ON ON OFF ON OFF ON ON
216 OFF OFF OFF ON ON OFF ON ON
217 ON OFF OFF ON ON OFF ON ON
218 OFF ON OFF ON ON OFF ON ON
219 ON ON OFF ON ON OFF ON ON
220 OFF OFF ON ON ON OFF ON ON
221 ON OFF ON ON ON OFF ON ON
222 OFF ON ON ON ON OFF ON ON
223 ON ON ON ON ON OFF ON ON
224 OFF OFF OFF OFF OFF ON ON ON
225 ON OFF OFF OFF OFF ON ON ON
226 OFF ON OFF OFF OFF ON ON ON
227 ON ON OFF OFF OFF ON ON ON
228 OFF OFF ON OFF OFF ON ON ON
229 ON OFF ON OFF OFF ON ON ON
230 OFF ON ON OFF OFF ON ON ON
231 ON ON ON OFF OFF ON ON ON
232 OFF OFF OFF ON OFF ON ON ON
233 ON OFF OFF ON OFF ON ON ON
234 OFF ON OFF ON OFF ON ON ON
235 ON ON OFF ON OFF ON ON ON
236 OFF OFF ON ON OFF ON ON ON
40 / 40
237 ON OFF ON ON OFF ON ON ON
238 OFF ON ON ON OFF ON ON ON
239 ON ON ON ON OFF ON ON ON
240 OFF OFF OFF OFF ON ON ON ON
241 ON OFF OFF OFF ON ON ON ON
242 OFF ON OFF OFF ON ON ON ON
243 ON ON OFF OFF ON ON ON ON
244 OFF OFF ON OFF ON ON ON ON
245 ON OFF ON OFF ON ON ON ON
246 OFF ON ON OFF ON ON ON ON
247 ON ON ON OFF ON ON ON ON
248 OFF OFF OFF ON ON ON ON ON
249 ON OFF OFF ON ON ON ON ON
250 OFF ON OFF ON ON ON ON ON
251 ON ON OFF ON ON ON ON ON
252 OFF OFF ON ON ON ON ON ON
253 ON OFF ON ON ON ON ON ON
254 OFF ON ON ON ON ON ON ON
255 ON ON ON ON ON ON ON ON
6.2. OSD MENU DIAGRAM
Please see the next two pages.
Table 30: SWITCH2 SETTING
41 / 41
(To be continued)
MAIN MENU
< SYSTEM INFORMATION >
< DISPLAY SETUP >
< DOME SETTINGS 1 >
< DOME SETTINGS 2 >
< DOME LABEL >
RESET CAMERA
REBOOT SYSTEM
LANGUAGE
ENGLISH
EXIT
SYSTEM INFORMATION
COM 2400,N,8,1
ADDRESS 1
PROTOCOL PELCO-D
PRESETS 256
LANGUAGE ENGLISH
TEMPERATURE 36°C
SOFTWARE VERSION V4.3.3
BACK
EXIT
DISPLAY SETUP
PRESET LABEL ON
ZONE LABEL ON
ZOOM ON
P/T DEG ON
DOME LABEL ON
<LABEL POSITION>
TEMPERATURE OFF
BACK
EXIT
DOME SETTINGS1
<CAMERA>
<MOTION>
<POWER UP>
<PRESETS>
<PATTERNS>
<ZONES>
<CLEAR SET>
TOTAL PRESETS NUMBER 256
BACK
EXIT
DOME SETTINGS 2
<ALARMS>
<ADDR SETTING>
<PASSWORD>
<WINDOWS BLANKING>
<HEATER SETTING>
<CRUISE SETTING>
<TRACKING SETTING>
BACK
EXIT
ZONE DOME PRESET
P/T DEG ZOOM
DIGITAL ZOOM OFF
BACKLIGHT COMP OFF
<PROGRAM AE MODE>
<ADDITIONAL>
WIDE DYNAMIC RANGE OFF
BACK
EXIT
AUTO FLIP ON
PROPORTIONAL PAN ON
PARK TIME 15S
PARK ACTION NONE
SCAN SPEED<DEG/S> 1
<SET SCAN>
<MANUAL LIMIT>
<SET AZIMUTH ZERO>
<CLEAR AZIMUTH ZERO>
BACK
EXIT
POWER UP ACTION NONE
BACK
EXIT
PRESET NUMBER 1
…PRESET NOT DEFINED…
<EDIT PRESET LABEL>
<EDIT PRESET POSITION>
<CLEAR CURRENT PRESET>
BACK
EXIT
PATTERN NUMBER 1
<PROGRAM PATTERN>
<CLEAR CURRENT PATTERN>
BACK
EXIT
ZONE NUMBER 1
…ZONE NOT DEFINED…
<EDIT ZONE LABEL>
<EDIT ZONE>
ENABLE ZONE ON
<CLEAR CURRENT ZONE >
BACK
EXIT
CLEAR ZONES
CLEAR PRESETS
CLEAR PATTERNS
RESTORE FACTORY DEFAULT
BACK
EXIT
SAVE
RESET
CAMERA
MOTION
POWER UP
PRESETS
PATTERNS
ZONES
CLEAR SET
PROGRAM AE CONTROL
AE MODE AUTO
LOW LIGHT MODE AUTO
LOW LIGHT LIMIT 1/50
IRIS LEVEL F2.0
AGC LEVEL 0DB
BRIGHT LEVEL 0DB/F2.0
SPOT AE OFF
BACK
EXIT
ADDITIONAL
IR SW MODE AUTO
IR STATUS COLOR
AUTO IRIS ON
SHARPNESS ON
SHARPNESS LEVEL 5
AUTO WHITE BALANCE AUTO
R GAIN 214
B GAIN 164
BACK
EXIT
PRESET NUMBER 1
PRESET LABEL 1 - - - - 0 1 2 3 4 5 6 7 8 9 Y Z y
z
A B C D E F G H I J K L M
N O P Q R S T U V W X
a b c d e f g h I j k l m
n o p q r s t u v w x
OK CANCEL
SP A C E
BACKSPACE`
ZONE NUMBER 1
PRESET LABEL 1 - - - - 0 1 2 3 4 5 6 7 8 9 Y Z y
z
A B C D E F G H I J K L M
N O P Q R S T U V W X
a b c d e f g h I j k l m
n o p q r s t u v w x
OK CANCEL
SP A C E
BACKSPACE`
42 / 42
DOME SETTINGS 2
<ALARMS>
<ADDR SETTING>
<PASSWORD>
<WINDOWS BLANKING>
<HEATER SETTING>
<CRUISE SETTING>
<TRACKING SETTING>
BACK
EXIT
ALARM NUMBER 1
SEQUENCE(SECS) 1
ALARM ACT CRUISE
ACTIVATE AUX OFF
<CLEAR SET>
DWELL TIME<SECS>1 0
DWELL TIME<SECS>2 0
BACK
EXIT
ALARMS
ADDR SETTING
ADDR TYPE HARD
ADDR SOFT 255
ADDR HARD 0
BACK
EXIT
ENABLE PASSWORD OFF
<EDIT PASSWORD>
BACK
EXIT
STYLE GRAY
BLANK ALL ABOVE OFF
BALANK ALL BELOW OFF
<SET WINDOWS>
SET MASK COLOR 4
BACK
EXIT
PASSWORD
WINDOWS BLANKING
SET WINDOWS
WINDOWS NUMBER 1
<EDIT WINDOW LOCATION>
<EDIT WINDOW ZOOM >
ENABLE WINDOW OFF
CLEAR CURRENT WINDOW
BACK
EXIT
HEATER SETTING
HEATER DISPLAY ON
HEATER MODE AUTO
TEMPERATURE SET 33℃
BACK
EXIT
DWELL TIME<SECS> 7
PRESET LIST 1
OFF
1234567890 <PRESET 1-10>
0110010111
BACK
EXIT
DEFAULT SETTING
SIZE SENS MEDIUM
GRAY SENS MEDIUM
LOST ACT STOP TRACK
ZOOM SETTING ON
WAIT TIME<S> 40
<TRACKING BOUNDARY>
AUX OFF
TRACKING SPEED AUTO
TRACKING TIME<M> AUTO
BACK
EXIT
CRUISE
1 ON 0
TRACKING SETTING
EDIT WINDOW ZOOM
IRIS OPEN TO CONTINUE
IRIS CLOSE TO CANCEL
EDIT WINDOW LOCATION
IRIS OPEN TO CONTINUE
IRIS CLOSE TO CANCEL
TRACKING BOUNDARY
BOUNDARY LIMIT OFF
CLEAR BOUNDARY
LEFT LIMIT OFF
RIGHT LIMIT OFF
UP LIMIT OFF
DOWN LIMIT OFF
BACK
EXIT
DOME LABEL
<EDIT DOME LABEL>
<CLEAR DOME LABEL>
BACK
EXIT
EDIT DOME LABEL
DOME LABEL
0 1 2 3 4 5 6 7 8 9 Y Z y
z
A B C D E F G H I J K L M
N O P Q R S T U V W X
a b c d e f g h I j k l m
n o p q r s t u v w x
OK CANCEL
SPACE BACKSPACE
43 / 43
Loading...