TESTPTZ705ADHS
IP camera tester
User Manual
Content
1 .Safety information ----------------------------------------------------------------------------------------------------- 1
2. IP Camera Tester Introduction --------------------------------------------------------------------------------------- 1
2.1 General ----------------------------------------------------------------------------------------------------------- 1
2.2 Features----------------------------------------------------------------------------------------------------------- 2
2.3 Function ---------------------------------------------------------------------------------------------------------- 5
2.4 Packing list ---------------------------------------------------------------------------------------------------- 12
2.5 Function interface -------------------------------------------------------------------------------------------- 13
3. Operation -------------------------------------------------------------------------------------------------------------- 16
3.1 Installing the Battery ----------------------------------------------------------------------------------------- 16
3.2 Instrument connection --------------------------------------------------------------------------------------- 17
3.2.1 IP camera connection -------------------------------------------------------------------------------------- 17
3.2.2 Analog camera connection ------------------------------------------------------------------------------- 18
3.2.3 HD Coaxial camera connection ------------------------------------------------------------------------- 18
3.2.4 HDMI IN ---------------------------------------------------------------------------------------------------- 19
3.3 OSD menu ----------------------------------------------------------------------------------------------------------- 19
3.3.1 Lite mode& Normal mode ------------------------------------------------------------------------- 20
3.3.2 Drop-down Menu ------------------------------------------------------------------------------------ 23
3.3.3 Short cut-menu --------------------------------------------------------------------------------------- 24
3.3.4 Screen capture ---------------------------------------------------------------------------------------- 25
3.3.5 TesterPlay --------------------------------------------------------------------------------------------- 26
3.3.6 Rapid video ------------------------------------------------------------------------------------------- 27
3.3.7 IP discovery ------------------------------------------------------------------------------------------- 28
3.3.8 Rapid ONVIF test ------------------------------------------------------------------------------------ 29
3.3.9 IP camera test ----------------------------------------------------------------------------------------- 44
3.3.10 HDMI IN --------------------------------------------------------------------------------------------- 46
3.3.11 Video monitor test---------------------------------------------------------------------------------- 50
3.3.12 Color-bar generator (TV OUT) ------------------------------------------------------------------ 59
3.3.13 CVI camera test ------------------------------------------------------------------------------------- 61
3.3.14 TVI camera test ------------------------------------------------------------------------------------- 68
3.3.15 AHD camera test ----------------------------------------------------------------------------------- 70
3.3.16 Network tool ---------------------------------------------------------------------------------------- 71
（1）IP address scan -------------------------------------------------------------------------------------- 71
（2）PING Test -------------------------------------------------------------------------------------------- 72
（3）Network test (Ethernet bandwidth test) --------------------------------------------------------- 72
（4）Port Flashing ----------------------------------------------------------------------------------------- 76
（5）DHCP server ----------------------------------------------------------------------------------------- 77
（6）Trace route ------------------------------------------------------------------------------------------- 77
（7）Link monitor ----------------------------------------------------------------------------------------- 78
3.3.17 Rapid IP Discovery -------------------------------------------------------------------------------- 79
3.3.18 PoE power / DC12V 2A and DC 5V 2A USB power output ------------------------------- 80
3.3.19 Cable Test ------------------------------------------------------------------------------------------ 81
3.3.20 RJ45 cable TDR test ------------------------------------------------------------------------------- 82
3.3.21 PoE Voltage test ------------------------------------------------------------------------------------ 85
3.3.22 12V power input test ------------------------------------------------------------------------------- 86
3.3.23 Audio Record --------------------------------------------------------------------------------------- 86
3.3.24 Data monitor ---------------------------------------------------------------------------------------- 87
3.3.25 Audio player ----------------------------------------------------------------------------------------- 87
3.3.26 Media Player ---------------------------------------------------------------------------------------- 88
3.3.27 RTSP Player ----------------------------------------------------------------------------------------- 88
3.3.28 Hik test tool------------------------------------------------------------------------------------------ 90
3.3.29 Dahua test tool -------------------------------------------------------------------------------------- 92
3.3.30 Update ------------------------------------------------------------------------------------------------ 96
3.3.31 Office ------------------------------------------------------------------------------------------------- 97
3.3.32 LED Flashlight -------------------------------------------------------------------------------------- 97
3.3.33 Browser ---------------------------------------------------------------------------------------------- 98
3.3.34 Notepad:---------------------------------------------------------------------------------------------- 98
3.3.35 System Setting -------------------------------------------------------------------------------------- 99
3.3.36 File explorer ---------------------------------------------------------------------------------------- 104
3.3.37 Theme ----------------------------------------------------------------------------------------------- 105
3. 4 Audio test ---------------------------------------------------------------------------------------------------- 108
3.5 HDMI output ------------------------------------------------------------------------------------------------- 108
3.6 PoE power output -------------------------------------------------------------------------------------------- 108
3.7 DC12V 2A power output ---------------------------------------------------------------------------------- 109
4. Specifications -------------------------------------------------------------------------------------------------------- 111
Page.1.
1 .Safety information
◆ The tester is intended to use in compliance with the local rules of the electrical usage and avoid to
apply at the places which are inapplicable for the use of electrics such as hospital, gas station etc.
◆ To prevent the functional decline or failure, the product should not be sprinkled or damped.
◆ The exposed part of the tester should not be touched by the dust and liquid.
◆ During transportation and use, it is highly recommended to avoid the violent collision and vibration
of the tester, lest damaging components and causing failure.
◆Don’t leave the tester alone while charging and recharging. If the battery is found severely hot, the
tester should be powered off from the electric source at once. The tester should not be charged over 8
hours.
◆ Don’t use the tester where the humidity is high. Once the tester is damp, power off immediately and
move away other connected cables.
◆ The tester should not be used in the environment with the flammable gas.
◆ Do not disassemble the instrument since no component inside can be repaired by the user. If the
disassembly is necessary indeed, please contact with the technician of our company.
◆ The instrument should not be used under the environment with strong electromagnetic interference.
◆ Don’t touch the tester with wet hands or waterish things.
◆ Don’t use the detergent to clean and the dry cloth is suggested to use. If the dirt is not easy to remove,
the soft cloth with water or neutral detergent can be used. But the cloth should be tweaked
sufficiently.
2. IP Camera Tester Introduction
2.1 General
The 7 inch touch screen IP camera monitor is designed for maintenance and installation of IP cameras,
analog cameras, TVI, CVI AHD, cameras, as well as testing 4K H.264 /4k H.265 camera via
mainstream, The 1280x800 resolution enables it to display network HD cameras and analog cameras in
high resolution. The unit supports many ONVIF PTZ and analog PTZ control. The combination of
Page.2.
touch screen and key buttons make the IP camera tester very user- friendly.
The tester is also a great tool for Ethernet network testing. It can test PoE power voltage, PING, and IP
address searching. You can use the blue cable tracer to locate individual connected cables from a bundle
of cables. Test LAN cable for proper connection termination. Other functions include providing 24W
PoE power to your camera, HDMI IN and out, CVBS loop test , testing IP and analog at the same time,
LED Flashlight, DC 12V 2A power output and much more. Its portability, user-friendly design and
many other functions make the IP tester an essential tool for all installers or technicians.
2.2 Features
New 7 inch IPS touch screen cctv tester,1280*800 resolution.
H.265&H.264, 4K display via mainstream.
IP and analog testing at the same time.
In HDMI IN mode, It can converter test from analog to digital with dual test window IP &
HDMI IN or Analog & HDMI IN
RJ45 cable TDR test and cable quality test, to test cable pair status, length, attenuation
reflectivity, impedance, skew and other parameter.
Screen capture, long press the key “enter”, can capture screen interface and save it in any time
12V power input test
“TesterPlay” app, support Tester, PC and mobile phone display at the same time. The android
version mobile phone install “TesterPlay ” app, or install VLC player in the PC, can real-time
receiving screen information from the tester Screen management, change function’s icons order,
create new directory.
Themes: Lite mode and normal mode can select , change the icons and desktop.
background ,change sliding effect etc.
Page.3.
Built in Wi-Fi ,display image from the wireless camera , create WIFI hotspot.
Rapid video, auto scan the IP camera address, via one key to view the image.
Screen lock : password lock and pattern lock are optional.
Office, quick office app (support excel, word, ppt format) doc. Editable.
Rapid IP scan , auto scan whole network or other network device ‘s IP address.
CVBS loop test , tester can receive and send the color bar generator ,to check BNC cable.
Traffic monitoring of the tester "Lan port", display network port or WIFI connection
real-time .upload and download speeds and other network parameters.
Shortcut button, drop-down menu ,PoE power switch ,IP setting, WLAN switch , HDMI IN
functions,screen lock, password lock screen or pattern lock etc.
IP discovery, do not need to know the first two digits of camera’s IP address , it can auto-scan
the whole network segment IP, and auto-modify tester’s IP address.
Rapid ONVIF, search camera quickly, auto log in and display image from the camera, activate
Hikvision camera.
Hik test tool app is design for activating and debugging Hikvision camera, can auto-identify
unactivated hikvision camera, also can display image from the Hikvision camera.
DH test tool app is design for Dahua Camera test, and modify IP, user name and password parameters etc.
ONVIF camera test, support 4K.
It is used unique hardware decoding, display image from the 4K camera via mainstream.
You can select sub-stream to test higher resolution camera.
ONVIF IP camera video testing.
Compatible with H.265/H.264/MPEG4/MJPEG IP cameras, such as Dahua, HIKVISION, and
ACTI Customized service are available.
Built in Wi-Fi, can receive image from wireless camera, as well as ONVIF and customized IP
cameras.
HD CVI camera image display, zoom, video record and playback ,Coaxial PTZ control and call
camera OSD menu
Page.4.
HD TVI camera image display, zoom, video record and playback ,Coaxial PTZ control and call
camera OSD menu
AHD camera image display, zoom, video record and playback, Coaxial PTZ control and call
camera OSD menu
HDMI signal output, supports up to 1080P.
Analog camera image display, auto adapt and display the video format of NTSC/PAL.
Support more than 30 protocols, such as PELCO-P,PELCO-D,SAMSUNG etc.
Video image digital zoom to view the image in greater detail.
Snapshot function allows you to save the current image as a JPG file in the SD card.
Built in enhanced image generator, send the color, pure blue and black image, test monitor
transmission channel and debug display device, observe whether there are light spots or black
spots on the monitor.
LED Flashlight.
8GB Micro SD card included.
LCD screen brightness/contrast/color Saturation adjustable.
Enhanced Color bar generator, PAL/NTSC multi-system color bar video generator (Eight-system
switchable, transmit/receive eight-system colorful images).
Ping test, PING is the most conventional network debugging tools; it is used for testing if the
connected IP camera or other network equipment’s Ethernet port is working normally and the IP
address is correct.
In digital IP surveillance applications, if the IP camera’s IP address is not known, the device
cannot be used. An IP address scan can quickly search for the connected IP camera or other
network device’s IP address.
The PoE voltage test can test for PoE voltage when a POE switch is supplying POE power to IP
camera.
Cable test , Test LAN cable or telephone cable,UTP cable etc ,cable type and the sequence of
wires will be displayed.
Support RS485,rate 600 ～ 115200bps adjustable.
Page.5.
PTZ protocol analysis, control protocol command displays to check RS485 transmission
whether is normal, easy to find the fault device.
PTZ control. Pan/tilts the P/T unit, zooms in/out the lens, adjusts the focus, aperture and
sets and the preset position.
DC5V 2A power output for USB charging (No USB data exchange, voltage only)
PoE power output, supply temporary power for PoE camera.
DC5V 2A power output, as a power bank.
Audio input and output, test and output the audio signal.
7.4V Lithium Ion Polymer Battery ,Working time lasts 10 hours, after charging for 6 ~7 hours.
2.3 Function
H.265 mainstream test
With the new hardware decoding, display the image from the 4 K H. 265 camera.
IPS display and touch screen operation
7 inch IPS touch screen cctv tester , 1280*800 resolution.
Intelligent interface
You can select “Lite mode or “Normal mode”. In normal mode, self-define desktop, press functions
icons to enter screen management status. You can move the icon to any pages; self-define the number of
icons in any page,Make interface sample and individuality.
HDMI HD digital signal input
HDMI digital input , support resolution 720×480p /720×576p /1280×720p /1920×1080p
/1024×768p/1280×1024p /1280×900p /1440×900p. Digital video recorder and other devices can display
images of the tester through the HDMI input.
Page.6.
RJ45 cable TDR test
RJ45 cable TDR test and cable quality test, to test cable pair status, length, attenuation reflectivity,
impedance, skew and other parameter.
Screen capture
Screen capture, long press the key “enter”, can capture screen interface and save it in any time
12V power input test
show the current adaptor input voltage and power.
TesterPlay
“TesterPlay” app, support Tester, PC and mobile phone display at the same time. The android version
mobile phone install “TesterPlay ” app, or install VLC player in the PC, can real-time receiving screen
information from the tester
It can converter test from analog to digital with dual test window IP & CVBS.
Dual test window ,IP & HDMI IN or Analog & HDMI IN.
Theme
Set function apps background, you can select 4 different colors at the same time. Set the desktop and
application interface background, you can choose pure colors or custom pictures. You also can change
RGB to set color. When you choose sliding effect, "three-dimensional, folding, left and right folding,
rotation, ombre effect" are optional.
Rapid video
Auto scans whole network IP address, by one key to detect all network cameras and auto display the
images.
Wireless WIFI
Built in Wi-Fi, can receive WIFI network camera images (ONVIF or customized camera) or network
Page.7.
data, etc. create Wi-Fi hotspot.
Screen lock
You can choose password Lock screen, pattern Lock screen or “NO”.
Office Software
Built in Quick office app ,can edit the documents, spreadsheets, and presentations etc.
Speed IP exploration
Search IP address of the connected IP camera or other network equipments in whole network segment.
Traffic monitoring
Traffic monitoring of the tester "LAN port", display network port or WIFI connection real-time upload
and download speeds and other network parameters.
Drop-down menu
Press and slide at right top right corner twice to open shortcut menu. The shortcut menu includes POE
power output, IP settings, Wi-Fi, HDMI IN, CVBS, Video OUT, LAN, Brightness, settings etc.
CVBS loop test
“TV out” testing app, it can send and receive color bar generator through the tester’s video out and
video in”.
IP discovery
IP discovery, do not need to know the first two digits of camera’s IP address , it can auto-scan the
whole network segment IP, and auto-modify tester’s IP address.
Rapid ONVIF
Rapid ONVIF, search camera quickly, auto log in and display image from the camera, activate
Hikvision camera.
Hik test tool
Page.8.
Hik test tool app is design for activating and debugging Hikvision camera, can auto-identify unactivated
hikvision camera, also can display image from the Hikvision camera.
DH test tool
DH test tool app is design for Dahua Camera image test, modify IP, user name and password
parameters etc.
IP camera test
The device is designed for ONVIF IP camera testing. It can display the image from an IP camera and
change the IP address.
The 7 inch 1280x800 screen display allows the user to view the image with a sufficient screen size.
With the ONVIF tool, you can display the image from an IP camera and use the PTZ functions.
Currently the IP camera tester supports more than 80 brands IP cameras, such as ACTi, Dahua,
Hikvision, Samsung, Honeywell and many more.
OEM service is available. Users can send us the IP camera for our engineers try to add the protocols to
the tester, or send us the mobile apps (Android version. APK files) to install in the tester.
Analog camera test
Supports PAL & NTSC formats. The LCD screen's back light brightness, video image brightness,
contrast and color saturation are all adjustable.
PTZ controller
Displays and allows for analysis of analog video and controls Pan/tilt/zoom function of PTZ analog
cameras. For PTZ testing, setup the controlling parameters from the meter to match those of the camera:
e.g. PTZ protocol (PELCO-D, etc.), communication port (RS-485, etc.), baud rate, PTZ camera ID and
pan/tilt speed.
Enhanced Color bar generator
The tester sends out color bars via its BNC output to the monitor. This is used to test for a problem in
Page.9.
the cable going from the camera back to the monitoring area.
12VDC 2A power output port and 5VDC 2A USB power port
The unit can power a camera with its DC 12V 2A power output. Also included is a built in DC 5V 2A
power output port used to charge USB devices. NOTE: This USB port is for charging only and has no
ability to transfer data.
Audio testing
Test the audio from mic level input devices. Connect the tester and mic level device with the audio
cable. Supports audio recording and output. to monitor and / or record audio.
Cable tester
Test LAN cable or telephone cable.
Connect LAN cable or telephone cable with the CCTV tester and cable tester. And then the connecting
status, cable type and the sequence of wires will be displayed, as well as display the serial number of
the cable tester kit.
PTZ data analysis
Search the Control protocol code from Multifunction keyboard or DVR by RS485 interface, test the
PTZ control command data whether received anomaly and RS485 data transmission.
Screen displays 16 hexadecimal codes such as
PELCO-P:A0 00（Add） xx xxxxxx AF xx
PELCO-D:FF 01（Add）xx xxxxxxxx
Digital Image zoom on the monitor
Set image zoom up to 4X to get a closer look at all the image detail. Supports analog and many IP
cameras
Video screenshot, record and playback
Capture the video image displayed and save as a JPEG file. You can also record and save the current
video to the SD card. The recorded files can play directly via Media player or under the function of
“Playback”.
Page.10.
Improvement color bar generator
Video generating, the PAL/NTSC multi-system color bar video generator and pure blue /black colorful
images, by receiving the video color bar to test the video channel whether transmit normally. And judge
whether the color is different, because of the transmission loss or interference, it suitable for Video
transmission of the field tests, such as optical video transmitter and receiver, video cable etc.
The new function color bar can test the image whether shift.
The color bar (red, green, blue, white, black) test the monitor whether have white or black dot etc.
DHCP dynamic address assignment
Built in DHCP server: Dynamically assign IP address for the IP camera or network device.
Access the dynamic IP address
The IP tester can directly access a dynamic IP address assigned from its DHCP server and use it as the
tester’s IP address. No need to set a IP address manually.
Multiple network IP Cameras Test
Supports Multi- segmented Static IP address setting which can simultaneously test different segments of
IP network Cameras.
IP address scan
The IP address scan can quickly search for connected IP cameras or another network device IP address.
PING Test
PING is the most conventional network debugging tool,it is used for testing if the connected IP camera
or other network equipment is working normally and the IP address is correct.
Port Finder
The tester will send signals to make the connected PoE port flicker at a set frequency. This will enable
the installer to easily and quickly find the connected port for an Ethernet cable.
PoE Test
Page.11.
Test the PoE voltage from a PoE switch. The unit will clearly display the voltage for each wire in an
Ethernet cable.
LED Flashlight
Press the LED On/Off button to use the LED flashlight.
WIFI
With built in WIFI, you can view the video from a wireless camera (ONVIF or customized camera) or
connect to a Wireless network.
CVI camera test
HD CVI video surveillance testing, support720p 25,30,50,60fps / 1080p 25,30fps / 2560x1440P
25/30 fps, when CVI signal input, HD CVI camera image display, zoom, view photos, video
record and playback, Coaxial PTZ control and call up the camera OSD menu.
TVI camera test
HD TVI video surveillance testing, support720p 25,30,50,60fps/ 1080p 25,30fps/ 2048x1536P
18fps/ 2688x1520P 15fps/ 2560x1944P 12.5fps, when TVI signal input , HD TVI camera image
display, zoom ,view photos ,video record and playback .Coaxial PTZ control and call up the
camera OSD menu.
AHD camera test
AHD video surveillance testing, support 720p 25,30fps/ 1080p 25,30fps/ 2048x1536P 18,2
5,30fps/ 2560x1440P 15,25,30fps,when AHD signal input , AHD camera image display, z
oom ,view photos ,video record and playback ,Coaxial PTZ control and call up the came
ra OSD menu.
PoE power supply
Supports PoE 802.3at power at 48V and up to 24W.
HDMI signal output
Page.12.
The HDMI output port supports up to 1080p 60Hz resolution output.
Network bandwidth testing
The network bandwidth test needs two IP tester meters to test bandwidth: one as a transmitter, the other
as a receiver.
Screen image rotates 180 degrees
You can manually rotate the display 180 degrees using the settings.
FTP Server
Start the tester’s Wi-Fi or connect the tester’s LAN port to the network. Once the tester is online, start
its FTP Server and directly access files from the tester’s SD card. This also allows for the user to
upgrade the tester firmware.
2.4 Packing list
1). Tester
2). Adaptor DC12V 2A
3) Network cable tester
4) Polymer lithium ion battery (7.4V DC 5400mAh)
5). BNC cable
6). RS485 cable
7). Output Power cable
8). Audio cable
9). Safety cord
10). Tool bag
11). Manual
12).8GB SD card
Page.13.
2.5 Function interface
Page.14.
1
Press more than 2 seconds, turn on or off the device ,short press to turn on or off
the menu display
2 Menu key
3 4xzoom the image displays.
4 Far focus: Focus the image faraway
5 Near focus: Focus the image nearby
6 TELE: zoom in the image
7 WIDE: zoom out the image
8 Open/set ,Confirm the setting of parameters, open or enlarge the aperture
9
Return/Close : Return or cancel while setting parameters of the menu, close or
decrease the aperture
10 Upward, set function or add parameter. Tilt the PTZ upward
11
Rightward, select the parameter whose value will be changed. Add the value of the
parameter. Pan the PTZ right
12
Downward, set function or reduce the value of the parameter. Tilt the PTZ
downward
13 Leftward, select the parameter whose value will be changed
14 Confirm key
15
Return/Close : Return or cancel while setting parameters of the menu, close or
decrease the aperture
16 Patch
17
The charge indicator: it lights red while the battery is being charged. As the
charging is complete, the indicator turns off automatically
18 The RS485 data transmission indicator: it lights red while the data is being
Page.15.
transmitted
19 The data received indicator: it lights red while the data is being received
20 The power indicator: it lights green while the tester is powered on by the adapter
Top interface
Bottom interface
21
DC12V2A power output , for provisional DC power supply
22
HDMI IN
23
CVBS IN/AHD /TVI/CVI Coaxial interface /（BNC interface）
24
Video signal output（BNC interface）/ cable tracer interface
25
LED lamp
26
RS485 Interface: RS485communication for the PTZ
27
HDMI output interface
28
Micro SD card moveable,(comes with 8GB, supports up to 32GB)
Page.16.
29
UTP cable port: UTP cable tester port/ Cable tracer port
30
PSE power sourcing equipment. Tests PoE voltage
31
PoE power supply output or LAN test port (Use to test PoE or non-PoE IP camera)
32
Audio output and earphone interface
33
Audio input
34
USB 5V 2A power output (used only for power, not data)
35
DC12V2A charging interface
36
DC12V2A power output , for provisional DC power supply
3. Operation
3.1 Installing the Battery
The tester has built-in lithium ion polymer rechargeable battery. The battery cable inside battery
cabin should be disconnected for safety during transportation!
Prior to the use of the instrument, the battery cables inside the battery cabin should be well
connected.
Usually it doesn’t need to disconnect the cable at the normal use
Pressing the key continuously can power on or off the tester.
Notice:Pls use the original adaptor and connected cable of the device!
When the battery icon is full or the charge indicator turns off automatically, indicate the battery
charging is completed.
Notice: When the Charge Indicator turns off, the battery is approximately 90% charged.
The charging time can be extended for about 1 hour and the charging time within 12 hours will not
damage the battery.
Notice :Press the key several seconds to restore the default settings when the
instrument works abnormally.
Page.17.
3.2 Instrument connection
3.2.1 IP camera connection
Power an IP camera with an independent power supply, then connect the IP camera to the IPC tester’s
LAN port, if the link indicator of the tester’s LAN port is green and the data indicator flickers, it means
the IP camera and the IPC tester are communicating. If the two indicators don’t flicker, check if the IP
camera is powered on or the network cable is not functioning properly.
Note:1) If the IP camera requires PoE power, then connect the IP camera to the IP tester’s LAN port .
The tester will supply PoE Power for the IP camera. Click on the icon POE to turn the PoE Power off or
on.
2) If use the tester’s menu to turn off the tester’s PoE power supply, the PoE switch and the power
sourcing equipment are allowed to connect to the tester’s PSE port, and the PoE power will be supplied
to the IP camera by the tester’s LAN port. On this condition, the tester cannot receive data from IP
camera, but the computer connected to the PoE switch can receive the data via the the tester.
Warning: PoE switch or PSE power sourcing equipment only can be connected to tester “PSE
IN” port, otherwise will damage the tester.
Page.18.
3.2.2 Analog camera connection
(1) ) Connect the camera's video output to the IP tester’s VIDEO IN. The image will display on the
tester after pushing the PTZ icon.
(2) CCTV IP Tester “VIDEO OUT” interface connect to the Video input of monitor and optical video
transmitter and receiver, the image display on the tester and monitor.
(3) Connect the camera or the speed dome RS485 controller cable to the tester RS485
interface .(Note :positive and negative connection of the cable)
3.2.3 HD Coaxial camera connection
* CVI, TVI, AHD camera are classified as HD coaxial cameras. Hereby the following instruction of
how to connect CVI, TVI, and AHD camera to the tester.
Page.19.
(1) Connect the CVI camera's video output to the IP tester’s “CVI IN” interface, the image will display
on the tester. The tester only come with CVI input interface. There is no CVI output interface.
(2) Connect the CVI camera or the speed dome RS485 controller cable to the tester RS485 interface.
3.2.4 HDMI IN
DVR or other device’s HDMI in port connect to tester’s HDMI in port, the meter will display input
image
3.3 OSD menu
Press the key 2 seconds to turn on
Press the key again to turn off
Page.20.
short press the key to enter sleep mode, press it again to test.
If tester works abnormally and cannot be turned off , Press the key several seconds to turn off,
the tester reset.
3.3.1 Lite mode& Normal mode
Lite mode: You can easy find corresponding apps
In Lite mode, Press the icon several seconds, can move the icon to other apps
Page.21.
In lite mode, click the finger icon in the lower right corner to release lock icon, move icons and
change function icons sequence.
Normal mode
Tap the screen and slide left or right to change menu.
In normal mode, press icon several seconds, go screen management status. Change icons sequence and
move it to common tools bar.
Page.22.
You can move the icon to any pages; self-define the number of icons in any page. Make interface
sample and individuality.
Create New Folder: Drag the icon to the folder in top right corner, enter the folder name. Icon will be
auto placed in the new named folder.
Page.23.
Press the folder several seconds, to change the folder name, you can move the icon out of folder, the
folder will be auto deleted until move out all icons.
Select Icons to enter, if quit, please click
Click SD card, install or remove SD card.
3.3.2 Drop-down Menu
Press and slide at right top right corner twice to open shortcut menu. The shortcut menu includes POE
power output, IP settings, Wi-Fi, HDMI IN, CVBS, Video OUT, LAN, Brightness, settings etc.
Page.24.
HDMI: Click HDMI IN to enter,In HDMI IN mode, it can converter test from analog to digital
with dual test window IP & HDMIN or Analog & HDMI in.
CVBS: Click icon “CVBS “to enter, you can test IP and analog camera at the same time.
Video OUT: Click Video OUT to enter floating window, connecting the BNC cable to tester
and appears analog video monitor interface, it can test circuit and BNC cable whether normal.
LAN: Display network port or WIFI connection real-time upload and download speeds and
other network parameters.
Brightness: Set brightness.
Settings: Enter settings interface.
IP: Enter IP Settings interface.
POE power output: Turn on or off the tester “PoE power “app.
WLAN: Turn on WLAN net and displays current WLAN status.
3.3.3 Short cut-menu
You can call shortcut –menu by press tester’s “menu” key, you can self- define shortcut -menu
Page.25.
Press the key“ ”, you can turn on it, and switch functions, then press to enter app, tap
other area on the screen, to exit the menu
Short cut-menu setting, you can long press any app in the all applications list ,it will auto move to
shortcut menu . If delete any app in the short cut – menu ,please select a app and press several
seconds ,it will be deleted.
3.3.4 Screen capture
long press the key “enter”, can capture screen interface and save it in any time.
Page.26.
You can go file management to view “file management –sdcard- Pictures—Screenshots
3.3.5 TesterPlay
Mobile screen projection (Only for android version)
The meter creates WIFI hotspot, connect mobile phone to the tester’s WIFI hotspot, or the tester
and mobile phone connect to the same Wi-fi network. Tap icon “ ”, then select
“TesterPlay” app to enter, the meter generates two-dimensional code, Please use mobile phone
scan it, then download and install the client software, you can view the screen real-time
projection.
PC screen projection：
Install VLC player in the PC, turn on the VLC player "Media - Open Network Streaming", and
input the RTSP address of on the top instrument two-dimensional code, click "play" to view the
screen real-time projection.
Page.27.
3.3.6 Rapid video
Press enter function, one key to detect all network cameras and auto play the images.
Page.28.
Auto log in and display camera image. Detailed operation refer to ONVIF function.
After enter ONVIF app, Click Refresh to search ip address.
3.3.7 IP discovery
Page.29.
Press IP discovery ,tester auto-scan the whole network segment IP, as well as auto-modify the
tester‘s IP to the same network segment with the scanned camera's IP.
Local IP：Tester’s IP address, Tester can auto-modify the tester‘s IP to the same network segment with
the scanned camera's IP
Discovery IP：Connected tester equipment’s IP address. If the camera connected to the tester directly,
tester will display the camera’s IP address, if tester connects to Local Area Network, it displays the
current IP address.
Temp IIP：after searching IP address, the modified tester’s IP address will not be saved, if you do not
select “Temp IP,” the modified tester’s IP address will auto-save after searching.
Start：PING function, Click "Start", can PING camera’s IP,
Rapid ONVIF:Rapid ONVIF Quick link
IPC TEST: IPC TEST Quick link
Applicability：Using IP discovery app ,you don’t need to know the first two digits of camera’s IP
address , it can auto-scan the whole network segment IP, and auto-modify tester’s IP address , greatly
improved engineering efficiency .
3.3.8 Rapid ONVIF test
Page.30.
Rapid ONVIF can display 4K H.265/H.264 camera image by tester mainstream, one key to activate
Hikvision camera.
Press enter ONVIF function, the meter auto scan all ONVIF cameras in different network
segments. It lists cameras name and IP address on the Left of screen. Tester can auto login camera and
display camera image. Factory default use admin password to auto login, if you modified the password,
then default use the modified password to log in.
If you select ONVIF Rapid mode, the meter automatically scan different network segments for ONVIF
cameras. It lists the camera name and IP address on the Device List. Tester can auto login camera and
display camera image.
Page.31.
Click the button “Refresh”, tester will scan the ONVIF camera again. Click the newly displayed ONVIF
camera on the “Device List“. The tester will show the IP camera’s relative information and settings.
Activate HIKVISION Camera: When connected unactivated HIKVISION Camera, tester can auto
recognized ,And prompt "The camera is not active, you need to activate it", click "OK" to start activate .
Enter a new password for the camera
When comes out “activate success” prompt, click login to display camera image.
Page.32.
Pop-up settings menu when click the “ONVIF setting ”icon in the upper left corner
Across network segments scan: After open this function , enter “Setting”-“IP Settings”-“Advanced”to
add other network segments IP, Rapid ONVIF function can across network segments to scan camera’s
IP.
Page.33.
Auto Login : After open this function, tester can auto login camera and display camera image. (The
login password is the same with last time, the first time using password is the default password
"admin")
Video transmission protocol: UTP and TCP protocol.
Open password cracker : Cracks password of cameras.
View manual : Open Manual.
Restore Defaults: Revert “Rapid ONVIF” to default settings.
Confirm : Save the modified parameters.
Click “MENU”icon to open camera setting .
While in the “Live video” menu, click “Video Menu” at the top right of the image to access the
following tools: Snapshot, Record, Photo, Playback, PTZ and Settings
Page.34.
ONVIF PTZ control: Tap the image in the direction you want the PTZ camera to move. Tap the left
side of the image to move left, right to go right, up to go up and down to go down. Compatible IP PTZ
cameras will rotate accordingly. PTZ rotation direction is displayed on top left corner of the image.
IP camera video settings: Click “Video Set” to enter the IP camera’s encoder and resolution settings.
Make the desired changes and click “OK “to save.
Page.35.
Image setting: Click “Imaging Set” to adjust image brightness, saturation, contrast, sharpness and
backlight compensation mode.
Profiles：Click “profiles"，can view video streaming current configuration files, as well as switch
between Major stream and minor stream.
Page.36.
Preview pictures：Quickly preview and zoom in or out pictures, automatically and manual refresh.
Identification: click “Identification” to view information of the camera.
Page.37.
Time set: click “Time set”, Select " Manual set" to set up the time of camera.
Maintenance: For camera software reset or restore to factory settings.
Page.38.
User Set: Modify camera user name ,password etc parameters
Network setting：Click “Network Set “to change the IP address. Some cameras cannot support change
IP address, so there is no change after saving.
Page.39.
Zoom in image :press the key to enter the zoom mode. Press it again to exit zoom mode.When
the image is enlarged tap left, right, up or down on the image to move the whole image on the screen
When the image is enlarged, if not operate on touch screen, it can operate by the keyboard ,press the
key to zoon in , press the key to zoom out ,press upward and downward key to
move image.
If it is network video input to the tester, as the tester supports resolution up to 1080p, the input image
will be very clear after it is enlarged. This is greatly helpful for the installers to ensure the IP camera’s
video coverage and decide the IP camera’s install site.
Image can only be enlarged on SD mode (The icon “ONVIF”is SD mode.)
Select relative function on the bottom Toolbar to operate, “Snapshot“ , “Record”, “Photos ”,
“Video playback”, “Storage set”, “PTZ control” etc.
Page.40.
Snapshot：Click bottom “snapshot” to screenshot the image and store it to SD card.
if select manual storage, appears dialog box “Input Name” , user-defined the files name(by Chinese
character, English letter ,or digit ) to save in SD card, if select “Auto- storage”，the tester auto stores the
files after snapshot.
Record：When you click bottom the “Record” icon, video starts recording. A red recording icon appears
on the screen and begins to flash and a timer appears indicating the time elapsed for the video. Click on
the “Stop” icon to stop recording and save the video file to the SD card.
Playback：Click the “Playback” icon to view saved videos. Double click the video you want to play.
Click to return to the last menu.
Page.41.
To rename or delete a photo, click and hold on the file until this screen appears:
Video files can play in the Video player on the main menu.
PTZ
Set preset position :Move the camera to preset position, enter the preset number on the Bottom right
corner to complete position preset.
Call the preset position : Select the preset number on the left, click "Call"to call preset.
Page.42.
PTZ Speed set : Horizontal and Vertical Speed set.
RTSP: Get RTSP address of the current camera
Doc: Auto generate test reports document of camera, click "generate document”. Click Preview to view
the report document.
Page.43.
Enter the camera test information, click "Generate Document" to complete the report.
Click “Doc” menu again, you can preview the report document.
Icons description: the description of function icons on the bottom toolbar.
Page.44.
3.3.9 IP camera test
Display image from the 4K H.265 camera by mainstream
Click icon to enter IP camera test
Note: Currently, the IPC Test App only supports some brands’ specific IP cameras,these include
specific models made by ACTI, AXIS, Dahua, Hikvision, Samsung, and many more. If the camera is
not fully integrated, please use the ONVIF or RTSP apps.
IPC test interface
Local IP: This is the tester’s IP address. Click “Edit“ to enter “IP setting“ and change the tester ‘s IP
address settings.
IP camera type : Click on the IP Camera type to select the Manufacturer and model number of the
integrated IP camera.
“Manual”：Click IP camera type, list Honeywell , Kodak,Tiandy, Aipu-waton, ACTi,WoshiDA IP
camera etc. If the brand has offered official original protocols, pls select camera type, input IP camera
address ,user name and password ,click” official” to enter the camera image display interface(Currently,
only support DAHUA official protocols )
Page.45.
Stream code: When test camera via RTSP, you can select mainstream or sub stream to test (if camera’s
RTSP have not been start or without, it will tip “auto match fail, please witch to manually selecting
IP Camera's IP: Enter the IP camera’s IP address manually or click “Search” to auto-scan for the IP
camera’s IP address. It is better to directly connect the IP camera to the tester so the
search results will only display the camera’s IP address. If the tester is connected to a
PoE switch, it will find and display several IP address.
Page.46.
IPC User Name: Enter IP camera’s user name.
IPC Password: Enter IP camera’s login password.
IPC Port :: When you select the IP camera type, it will default the camera’s port number and doesn’t
need to be changed.
After all settings are completed, click “Enter” to view the live video.
If IP address setting has error or IP camera is not connected.. The tester prompts “Network Error”
Click to quit from image display and return to IP camera test interface.
Once you are viewing video on the IPC Test app, you will see the “Video Menu” icon on the top
right. This button will give you access to Snapshot, Record, Photo, Playback, PTZ, and Set. Please refer
to the ONVIF section to use these functions.
3.3.10 HDMI IN
HDMI in HD signal test, Tap icon “ ”to enter
When tester receives HDMI in image, the top tool bar shows the resolution of this image. You can
select “resolution ”to set resolution in the setting menu .Tap screen by twice, full image display.
Support resolution below
720×480p /720×576p /1280×720p /1920×1080p /1024×768p/1280×1024p /1280×900p /1440×900p
Page.47.
(1) Snapshot
Click the icon “Snapshot “, when the video in, to take a picture and save the current video frame in the
SD card as JPEG file.
If the unit is set to the manual mode an “Input Name” pop up box will appear and you can enter a title
for the snapshot. If the unit is set up to automatically set file names, this box will not pop up.
Page.48.
(2) Video record
When you click the “Record” icon, video starts recording. A red recording icon appears on the screen
and begins to flash and a timer appears indicating the time elapsed for the video. Click on the “Record”
icon again to stop recording and save the video file to the SD card.
if select manual storage, before recording begins ,appears dialog box “Input Name” ,user-defined the
files name(by Chinese character, English letter ,or digit) to store in SD card , tester will hereby store the
files in SD card after recording . if select “Auto-storage ,tester will auto store the files in SD card after
recording .
(3)Photo
Click the icon “photo” to enter, click the selected thumbnail photo to display it on the screen.
Double-tap the image you want to view to make it full screen. Double-click again the photo to return.
Page.49.
To rename or delete an image, click and hold on the file until this screen below appears
Click to close and return to PTZ controller.
(4) Recorded video playback
Click the “Playback” icon to view your recorded videos. Tap on the video file image you want to watch.
Page.50.
To rename or delete a video, click and hold on the file until this screen appears:
Video files also can play in the main menu “Video Player".
3.3.11 Video monitor test
Analog camera test and PTZ control, click icon to enter
Display the input video image, click the top menu bar icon to enter video level meter,
(PEAK level, SYNC level, COLOR BURST measurement)
Page.51.
Select relative function on the right side Toolbar to operate , functions including “Photos”, “Snapshot” ,
“Record” , “Playback” , “PTZ” , “Set” ,
Click , or press to quit.
Click the screen twice quickly, can be full zoom in on the touch screen.
(1) PTZ controller parameter setting
Select and click icon “PTZ”, to enter PTZ setting:
A. Protocol
Use the up and down arrow keys to move the yellow cursor to the “protocol ”, set corresponding
Protocol and support more than thirty PTZ protocols. Such as
Pelco-D,Samsung,Yaan,LiLin,CSR600,Panasonic,Sony-EVI etc.
B. Port
Click and move, to “port” Select the communication port for the PTZ camera controlling (RS485)
C. Baud
Move the yellow cursor to “Baud”, Select the baud rate according to baud rate of the PTZ
camera.(150/300/600/1200/2400/4800/9600/19200/57600/115200)
D. Address
Set the ID according the ID of PTZ camera (0~254), the setting address data must be consistent the
Page.52.
speed dome address.
E. Pan speed: Set the pan speed of PTZ camera (0~63)
F. Tilt speed: Set the tilt speed of PTZ camera (0~63)
G. Set preset position (Set PS)
Click and select “Set PS”, set and save preset position number(1~128),
H. Call the preset position (Go ps)
Click and select “Set PS”, set and save preset position number (1~128), click “sure” to save,
Call some special preset number, can call the dome camera menu
Check and set the protocols, address, interface and baud, all must be consistent with the dome camera,
then the IPC tester can test .After setting the parameter, the tester can control the PTZ and lens
To control PTZ by screen touch:
Tap left, right, upward and downward on the touch screen to control the PTZ rotation direction. By two
fingers move outward and inward on the touch screen to zoom in and out the PTZ.
PTZ Control:
Press the key control the PTZ direction of rotation
Press the key or , to switch on or turn off the aperture.
Press the key or , adjust the focus manually
Press the key or , manually adjust the zoom
Page.53.
(2) Video and storage setting
Click icon “set”,to enter and set analog video image brightness , contrast, color saturation, as well as the
file storage way after snapshot and recording, support auto-storage and manual storage.
When select manual storage, user can name and store the files.
(3) 4 x zoom image display and Video out
When image input, press to enter “zoom”, press it again to quit.
Using the touch screen to control PTZ camera movement:
Tap left, right, upward or downward on the video image to move the PTZ camera in a desired direction.
Stretch two fingers outward or inward on the touch screen to zoom the image in or out.
Page.54.
If not use touch screen to operate, press the key to zoom out , press the key to
zoom in, press upward and downward key to move the image
For analog video input, as the resolution is 720*480, it is normal that the zoom in image is not
clear. But for network digital video input, as it supports resolution up to 1280*960, the zoom in image
is still very clear. This is very helpful for IP camera installation.
(4) Snapshot
Click the icon “Snapshot “, when the video in, to take a picture and save the current video frame in the
SD card as JPEG file.
If the unit is set to the manual mode an “Input Name” pop up box will appear and you can enter a title
for the snapshot. If the unit is set up to automatically set file names, this box will not pop up.
(5) Video record
When you click the “Record” icon, video starts recording. A red recording icon appears on the screen
and begins to flash and a timer appears indicating the time elapsed for the video. Click on the “Record”
icon again to stop recording and save the video file to the SD card.
if select manual storage, before recording begins ,appears dialog box “Input Name” ,user-defined the
files name(by Chinese character, English letter ,or digit) to store in SD card , tester will hereby store the
files in SD card after recording . if select “Auto-storage ,tester will auto store the files in SD card after
recording .
Page.55.
(6)Photo
Click the icon “photo” to enter, click the selected thumbnail photo to display it on the screen.
Double-tap the image you want to view to make it full screen. Double-click again the photo to return.
To rename or delete an image, click and hold on the file until this screen below appears
Page.56.
Click to close and return to PTZ controller.
(7) Recorded video playback
Click the “Playback” icon to view your recorded videos. Tap on the video file image you want to watch.
To rename or delete a video, click and hold on the file until this screen appears:
Page.57.
Video files also can play in the main menu “Video Player".
(8) Video level meter
Click the icon to enter, the IP camera tester has adopted hardware high-speed sampling and
processing technology, can perform both NTSC and PAL video amplitude signal measurements for
PEAK to PEAK, SYNC levels and COLOR BURST chroma level. When an analog signal is fed into
the meter, the tester displays the measurements on the bottom left corner of the screen
Page.58.
While in PAL format, the unit will be mV, While in NTSC format, it will be IRE.
Video signal PEAK to PEAK level:
For NTSC format, the video signal level is 140±15IRE
For PAL format, the video signal level is 1000±200mV
If the level is too low, it will cause the image to lose quality and limit the distance it will travel over
cable. If the level is too high, it will distort the image.
SYNC level: Tests the amplitude of the video sync pulse to verify if the video level is correct.
For NTSC format, the SYNC level is 40 ± 5IRE
For PAL format, the SYNC level is 300 ± 35mV
If the level is too low, it will cause the image to not frame out properly. If the level is too high, it will
lead to a poor quality image.
COLOR BURST level: Testing the color burst level will determine if the burst signal is sufficient to
trigger the displays color producing circuit. Burst will diminish in amplitude over longer cable runs and
can get fall below the threshold for the video display to show a color image.
NTSC
Video signal level
140±15IRE
Chroma level( COLOR BURST)
40±5IRE
SYNC signal level
40±5IRE
PAL
Video signal level
1000±200mV
Chroma level( COLOR BURST)
300±35mV
SYNC signal level
300±35mV
Page.59.
For NTSC format, the Chroma standard level is 40 IRE
For PAL format, the Chroma standard level is 280mV
If the Chroma level is too low, the color will not be as deep, and some details of the image will become
lighter. If the Chroma level is too high, there will be distortions on the image. If the coaxial cable is too
long, it will reduce the chroma level.
Image loop test：Test video optical transmitter and receiver and video cable, connect one end to the
tester “VIDEO OUT” port ,and the other end connected to “VIDEO IN” port, the signal send via
“VIDEO OUT” port ,and received via “VIDEO IN” port , If the testing is ok, the tester displays several
gradually dwindling photos on the desktop.
3.3.12 Color-bar generator (TV OUT)
Click to enter, the tester sends the color bars from the “Video out” port ,Click the icon “PAL”,
select “PAL/NTSC” output formats
Click the selected color-bars, testing image or single bar ( red, green, blue, white or black). Double click
to full display on the screen and output, click to return main menu.
Application
Page.60.
BNC loop test: Tester can send and receive color bar generator through the tester’s “video out and
video in” port, it is for testing transmission channels, such as video Optical, video cables etc. The tester
“VIDEO OUT” port to connect optical terminal’s sending port, and “VIDEO IN” Port to optical
terminal’ s connect its receiving port.
A. When maintaining the dome camera, the tester sends out the color bar by its BNC output to the
monitor at the monitoring center. If the monitor receive the color bar, it means the video transmit
channel works normally. Meanwhile on the basis of the received color bar, the monitoring center can
judge if transmission has loss or interference.
B. The tester sends out the pure color bar (such as white and black color), to test the monitor whether
has bright or black dots
C. The tester sends out video signal image to test if the image received by the monitor has excursion.
Page.61.
3.3.13 CVI camera test
HD CVI camera, CVI dome camera test and PTZ control, click icon to enter
When HD CVI signal input, the tester will display the image resolution on the top bar. Double-taps on
the screen to make the image displayed full screen.
The tester supports resolution as follows
1280x720P 25FPS / 1280x720P 30FPS / 1280x720P 50FPS / 1280x720P 60FPS
1920x1080P 25FPS / 1920x1080P 30FPS
2560x1440P 25FPS/2560x1440P 30FPS
Page.62.
（1）PTZ control
1.1 Coaxial PTZ control
Click the icon“PTZ”on the right toolbar to do the corresponding setting.
“Port”: select coaxial control
Enter PTZ address to perform parameters setting
Operation instructions, please refer to “3.3.1 PTZ (1) Video monitor test”
The PTZ address in the tester must be consistent with the dome camera or decoder, then the IPC
tester can test .After setting the parameter, the tester can control the PTZ and lens.
Page.63.
To control PTZ by screen touch:
Tap left, right, upward and downward on the touch screen to control the PTZ rotation direction, PTZ
cameras will rotate accordingly. By two fingers move outward and inward on the touch screen to zoom
in and out the PTZ.
To control PTZ by key buttons
Press arrow keys to control to control the PTZ direction of
rotation
Press the key to switch on or turn off the aperture.
Press the key , adjust the focus manually
Press the key , manually adjust the zoom
Set preset position
Setup preset position, move the PTZ camera to the preset position, the Tap it and input preset position
number. Tap “Set position” to complete set preset position
Page.64.
Call preset position
Tap the preset position:
Tap the preset position area, input preset position number. Tap “call position” to complete call preset
position.
Page.65.
1.2 RS485 control
Operation instructions, please refer to “3.3.1 PTZ (1) PTZ control parameters setting”
（2）Coaxial camera menu setting
Tap icon “UTC””, select “menu setting” to enter the dome camera menu.
Input calling dome camera menu address code, after finishing the parameter settings, you can press the
key or click the icon to call the dome camera menu .
Page.66.
Press arrow keys to set
(3) Snapshot, record, photo viewer and video play back, please refer to “3.3.1 PTZ (1) Video monitor
test”
Tap “close menu” or press the key “ ”to close camera menu.
Page.67.
(4) Save setting
Click icon “Set” on the right toolbar to enter storage setting.
Support auto-storage and manual storage.
When select manual storage, user can name and store the files.
Page.68.
3.3.14 TVI camera test
HD TVI camera, TVI dome camera test and PTZ control, Click icon to enter
When HD TVI signal input, the tester will display the image resolution on the top bar. Double-taps on
the screen to make the image displayed full screen.
The tester supports resolution as follows:
1280x720P 25FPS / 1280x720P30FPS / 1280x720P 50FPS / 1280x720P 60FPS
1920x1080P 25FPS / 1920x1080P 30FPS / 1920x1080P 50FPS / 1920x1080P 60FPS
2048x1536P 18 FPS /2688x1520P 15 FPS /2560x1944P 12.5 FPS
Page.69.
Coaxial camera menu settings
Tap icon “UTC”, select “menu setting” to enter the dome camera menu.
Input calling dome camera menu address code, after finishing the parameter settings, you can press the
key or click the icon to call the dome camera menu.
More operation instructions (such as PTZ control, coaxial camera menu setting ,snapshot, recording and
playback etc), please refer to“3.3.6 CVI camera test”.
Page.70.
3.3.15 AHD camera test
AHD camera, AHD dome camera test and PTZ control, Click icon to enter
When AHD signal input, the tester will display the image resolution on the top bar. Double-taps on the
screen to make the image displayed full screen.
The tester supports resolution as follows:
1280x720P 25FPS / 1280x720P 30FPS / 1920x1080P 25FPS / 1920x1080P 30FPS
2048x1536P 18 FPS/2048x1536P 25 FPS/2048x1536P 30 FPS
2560x1440P 15 FPS/2560x1440P 25 FPS/2560x1440P 30 FPS
Page.71.
(1) Coaxial PTZ control
UTC control : select “PTZ control or PTZ control-2”(AHD camera has two different order ,if select
“PTZ” cannot control , pls go “PTZ-2” )
If to coaxial PTZ control the AHD camera, no parameters setting is needed.
More operation instructions please refer to “3.3.6 CVI camera test”
3.3.16 Network tool
（1）IP address scan
Connect the cable to the LAN port, click icon to enter, Set your IP address search range by
changing the Start and End IP addresses. Click the “Start” button to scan the IP address range. You can
also input an IP address in the Port Number Scan to scan for open ports.
Page.72.
（2）PING Test
PING is the most conventional network debugging tool; it is used for testing if the connected IP camera
or other network equipment’s Ethernet port is working normally and the IP address is correct
Connect a network cable to the LAN port and click the icon to open the PING tool. You can set
your LOCAL (native) IP address, Remote IP address (e.g. IP camera), Packet count, Packet Size, Packet
time and Timeout. Press “Start” to start pinging. If the IP camera or network device is not configured
properly or not plugged in, it will say “Destination host unreachable,” or have 100% packet loss. If the
tester connects to the device, the send and receive packets will have a 0% packet loss.
Application: PING testing is the most conventional network debugging tools. It is used for testing if
the connected IP camera or other network equipment’s Ethernet port is working normally and the IP
address is correct.
It’s normal that the first data packet will be lost when test start.
（3）Network test (Ethernet bandwidth test)
Network test (Ethernet bandwidth test)
To use the Network tester, you will need two IP testers. One is used as a Server and the other as a Client.
Both devices must be on the same network segment in order to communicate. Click the icon to
open the Network Tester app.
Page.73.
When test, need a tester or a computer installed Network Test Software as the Server, the other tester
sends packet test. The two testers must be in the same network segment.
a).Start the server: Click “Start Server” button to use the tester as a Server. It will display its IP
address at the top of the screen.
b). Start send packet test: Using the other IP tester, type in the Server's IP address at the top right
corner of the screen. This app is used to send packets for network speed testing. Click the “Start” button
to send the packets and start testing.
Page.74.
Network bandwidth testing can also be tested with a computer using compatible network bandwidth
testing software. Install network bandwidth testing software on a computer, as a test Client or Server, to
do the mutual testing with the tester. If use computer as the server, the computer IP address
is :192.168.0.39
Tester as Client, tester’s IP address is:192.168.0.238. The Server and the Client are at the same network
segment, but with different IP address. Input Server’s IP address 192.168.0.39 in the tester and click
“Start” to test network bandwidth.
Page.75.
Or use tester as a Server, computer as test Client（select Client, input tester’s IP address to test）
When use tester as Server,shows results:
Page.76.
（4）Port Flashing
Connect a network cable to the meter’s “LAN” port, click the icon to open the Port Flashing
app. Click “Start”. The IP tester sends a unique signal to make the connected LAN port of the switch
flash.
If the tester and PoE switch are connected well, the LAN port of POE switch flash at special frequency,
If not, no any changes on the LAN port
Application:
The tester will send special signals to make the connected LAN port flicker at special frequency, which
will enable the installers to easily and quickly find the connected Ethernet cable. This function can
Page.77.
prevent mistakenly insertion or disconnection non-corresponding cable to artificially interrupt network
connection.
（5）DHCP server
Click on the DHCP icon to open the DHCP server app. Select the “Start” check box at the top and make
any desired changes to the network settings. Click “Save” to start assigning dynamic IP addresses for
IP cameras and other networked devices. Click the “Refresh” button to check your Client list.
（6）Trace route
It is used to determine path of the IP packet access target.
Note: Trace route testing results only for reference, for accurate test route tracking, Pls use professional
Ethernet tester.
Click to enter trace route
Input tracking IP address or domain name in the Remote Host IP. Set maximum hop count, normally
default is 30
Page.78.
Click “start” to trace the goal address
（7）Link monitor
Click the icon to open the Link Monitor app. This app is used to see if an IP address is occupied
by other network devices. This will avoid new address conflicts
Click “Add” and enter the desired IP address. To test different network segments, click the “Settings”
icon on the main menu and go to IP Settings and make the desired changes. Once the desired IP
addresses are added to the Link Monitor list, click “Start”. If the IP address status shows a check mark
the IP address is occupied. If the IP address status shows an X the IP address is available. Click “Stop”
Page.79.
to stop the testing
Application:
Add an IP camera or other network device to the current network group, the new IP address must not be
occupied, otherwise it will cause IP conflicts and stop the equipment normal working. Link monitor can
check if the new setting IP address is occupied.
3.3.17 Rapid IP Discovery
Connect the cable to tester’s Lan port. Press to enter Rapid IP Discovery app.
Click “Start “to search all IP address of connected equipments in whole network segment.
Click “Stop “to stop work.
Page.80.
3.3.18 PoE power / DC12V 2A and DC 5V 2A USB power output
When the tester is turned on, the 12VDC and 5VDC power output functions are automatically turned on.
If the IP tester is turned off, the 5VDC USB can still be used to power an external USB device.
To use the PoE Power Output function, click on the icon and change the switch “ON” or “OFF”.
The IP camera needs to be connected to the LAN port before you turn PoE Power on. If the IP camera
Supports PoE, the PoE power is delivered via pins 1, 2, 3, and 6 on the LAN port. The IP tester will
display “48V ON” at the top of the screen when the POE power is still on.
Note:
1. Don’t input power into the “DC12/2A OUTPUT” port.
2. Don’t output this DC12V/2A power to the DC12V/IN port of the IP camera tester to avoid destroy
3. The IPC tester power output is close to 2A, if the IP camera’s power is over 2V, the tester will auto
enter protection mode. Disconnect all the connections of the tester and then connect the tester with
power adaptor to resume the tester.
4. Before turning on the PoE power output, please make sure the IP camera supports PoE power.
Otherwise it may damage the IP camera.
5. Make sure you plug in your IP camera to the LAN port prior to turning on PoE power
6. Make sure the tester is full charged or more than 80% charged, otherwise the tester will shows
“low power”, “not able to supply power”.
Page.81.
3.3.19 Cable Test
Click icon to enter
Test LAN cable or telephone cable.
Connect LAN cable or telephone cable with the CCTV tester and cable tester. And then the
connecting status, cable type and the sequence of wires as well as the serial number of the cable tester
kit will be displayed.
The number of the cable tester is 255.
If need several different number other types cable testers, should pay the additional cost.
Cable test
Tap "cable test sketch map" ,pop up Straight-through cable and crossover cable skectch, It is for line
sequence reference ,when the crystal on the first pressure in the twisted-pair
Page.82.
3.3.20 RJ45 cable TDR test
Connect cable to tester’s LAN port, click icon “ ” to enter RJ45 cable TDR test app.
Single test: test cable status, length and attenuation.
Repeat test: continue to test cable status, length and attenuation.
Status: after link up, screen display “online”, if not link up or open circuit, screen display ”open
circuit”, if cable pair is short circuit, screen display “short circuit”
Length: the max test length is 180 meters, when cable is open circuit or short circuit, can test the
cable length, if screen display “online”, the testing result would be not accurate.
Cable quality test: Green is good quality cable, Yellow is Poor quality cable, Red is water
poured cable, the attenuation value will be displayed when cable over 10 meters
Page.83.
Advanced Test: test cable pair status, length, attenuation, reflectivity, impedance, skew and
other parameter.
Attenuation reflectivity: after link up, if reflectivity value is 0, it is the best quality
communication
Impedance: after link up ,if the impedance value is 100 Ω,it is the best quality communication,
the range is generally in 85-135 Ω
Skew: After 1000M link up, when skew value is 0ns,it is the best quality communication, if over
50ns, will cause a Bit Error Rate in the transmission.
Page.84.
Connection diagram
Cable sequence diagram:
A straight- through and cross-over cable diagram, the cable sequence display for reference
Click “Help”, check the instruction of all parameters.
Page.85.
3.3.21 PoE Voltage test
Click icon to enter PoE voltage measurement
Connect a network cable from a PoE switch to the IP tester’s PSE IN port. Connect an IP camera or
other PoE using node to IP tester’s LAN port, the PoE voltage and the cable’s pin connection status
show on the screen.
Note: This test if for measuring the voltage being drawn by the PoE node and the IP
tester must be between the PoE switch and the PoE node for this test to work.
Note: The PoE switch must be connected to the PSE IN port. The powered device such as IP
camera or other PoE node must be connected to the LAN port.
Note: Do not connect PoE power supply equipment (such as a PoE switch) to the tester’s
UTP/SCAN port; otherwise it will damage the tester.
PSE transmission
When PoE / PSE voltage testing, PoE/PSE conntect to the tester's PSE "IN" port , the camera connetct
to tester's Lan port , tester not only can transmit voltage to supply power for camera ,but also transmit
data at the same time. as well as the computer connect to the PoE/PSE, it can log in connected tester's
PoE camera.
Page.86.
3.3.22 12V power input test
Connect 12V power adaptor to tester’s charging port, then click icon “PoE” to enter voltage
measurement app ,screen show the current adaptor input voltage and power. Note: the current
12V input measured power is the battery charging power and the device working power,the
measured power will change depending on the different of battery power and backlight
brightness.
Warning: Not allow connect device with input power over 17V to tester “12V
IN“port,otherwiseit will damage the machine.
3.3.23 Audio Record
Connect an audio device to the IP tester’s audio input port. Click the icon to enter the Audio
Recorder app. Click the red button to stop, and the unit will prompt you to save the recording
Page.87.
3.3.24 Data monitor
Pls click icon to enter
Click “Setting” to choose the baud rate of RS485; it must be the same as the DVR or the Control
keyboard .The DVR or Control keyboard send the code to the tester, if it can be read, the protocol will
shown on the upper right, like Pelco D, if not, like P:---
While the tester receives the code, press the key to empty.
Though the RS485 port, display the PTZ control code of the multifunctional keyboard or the DVR.
Controller can check the status of the RS485 transmission through the code on the display. (The RS485
communication rate must be the same.)
Application: Check the RS485 communication states of the video optical transmitter whether normal.
Engineer can analyze the protocol and check the data through the displayed code.
3.3.25 Audio player
Click the icon to enter . The audio player only supports MP3 format Audio files.
Page.88.
3.3.26 Media Player
Click the icon to enter
The Media player can browse video and image files. It supports the video formats of MP4, H.264,
MPEG4, and MKV. The IP tester recorded files can play directly via the Media player. The Media
player will automatically display the video files from the SD card. Click on the desired file to play.
Click RETURN to exit.
To rename or delete an existing file, press the file name for a few seconds until the screen below
appears. You can then rename or delete the file by pressing the desired option.
3.3.27 RTSP Player
The RTSP Player app will allow you to view the RTSP video stream from an IP camera. If you were
unable to view your camera via the ONVIF or IPC Test apps, it is possible your camera will have an
Page.89.
RTSP stream and you can view live video.
From the main menu, select the “APP Tool” folder and then select the “RTSP Player” to open the app.
If the IP camera uses MJPEG, select the RTSP icon. If the IP camera uses H.264, select the “RTSP HD”
icon.
Local IP: This is the IP testers IP address.
RTSP Add: This is where you can manually enter the IP camera’s RTSP URL or click on Search to
search the network for cameras that use an RTSP stream.
IPC Username: Enter the IP camera’s user name.
IPC Password: Enter the IP camera’s password.
Once you have entered all the necessary information, select Enter at the bottom left to view the RTSP
stream.
Page.90.
Note: in the event the ip tester does not auto detect the rtsp stream, refer to the specific camera
manufacturer for the specific rtsp stream url. you may find this on line with a search of the
camera model number and the word rtsp.
3.3.28 Hik test tool
Hik test tool app is design for activating and debugging Hikvision camera, can auto-identify
unactivated hikvision camera, also can display image from the Hikvision camera.
Tap icon to enter
1. Hikvision activation：When connect the unactivated Hikvison camera to the tester, it will auto
identify and display “Unactivate” at safety mode. Select needed activate the camera, click bottom
right corner button “Enable”, pop-up “the camera is not activate, activate now”?
2.Input password：Input new password, tap “ok” to activate
Page.91.
3. Confirm activation
After activating the camera, the program default modifies the camera IP. Activated multiple cameras in
the local area Network, and pop-up menu to modify IP, improve project efficiency.
Play: display image from the camera
Modify network information: Change the camera IP address, subnet mask and gateway etc.
Page.92.
Modify user information: Modify the camera's user name and password.
Factory Reset：Camera factory reset
3.3.29 Dahua test tool
Dahua test tool is developed for installation and debugging of the Dahua IP camera, it can display
image, and modify IP, user name and password etc. Making Dahua camera test more convenient and
quickly.
Page.93.
Click “DH” icon , to enter Dahua test tool.
Select the camera of the online detection menu, if the camera support non-verification login, you can
click “play” directly, and view the image.
Pop up stream menu, select mainstream or second stream to test
Page.94.
If the camera not supports non-verification login, pls select “camera” of online detection menu, and
input correct user name and password, then click “log in”. After logging successful, you can test it.
Play: select mainstream or seconded stream, IP camera live video display.
Modify network information: modify camera parameter, such as ip address, subnet mask, gateway etc.
Page.95.
Modify user information: modify camera user name and password, which is onvif, Dahua test tool, IPC
TESTE user name and password, not web user name and password.
Factory reset setting: camera will be soft reset, and the device’s user name, password and network set
be saved. Other settings information is factory reset.
Page.96.
3.3.30 Update
Copy the downloaded update file to SD card "update" directory, if no directory, please create one.
Click the icon to open the Update menu. Select “Local Update” to update via the SD card or
select “Online Update” to check for updates on the internet. If there are applications that need updating,
the applications will be displayed on the
If there are update programs, applications will be listed in the interface, click related applications, update to the
latest version.
Update online: Before using online update, need enter settings-user management to register first.
Loading...