CCTV Tester Manual
V
2
.1
0
V
2
.1
0
V
V 2
2 .1
.1 0
0
Thank you for purchasing the CCTV security tester. Please read the manual before using the
CCTV tester and use properly.
For using the CCTV tester safely, please first read the 「 Safety Information 」 carefully in the
manual.
The manual should be kept well in case of reference.
Keep the S/N label for after-sale service within warranty period. Product without S/N label will
be charged for repair service.
If there is any question or problem while using the CCTV tester, or damages occurred on the
product, please contact our technical Department.
Content
Content
Content
Content
1 、 Safety information ............................................................................................................................. 1
2 、 Introduction ....................................................................................................................................... 2
2.1 General .................................................................................................................................... 2
2.2 Features ................................................................................................................................... 2
2.3 Function .................................................................................................................................. 4
2.3.1 Video signal testing .................................................................................................... 4
2.3.2 Video signal level test ................................................................................................ 4
2.3.3 PTZ controller ............................................................................................................ 4
2.3.4 Enhanced Color bar generator .................................................................................... 4
2.3.5 DC12V 1A output power ........................................................................................... 5
2.3.6 Audio testing .............................................................................................................. 5
2.3.7 Cable tester ................................................................................................................ 5
2.3.8 PTZ controller ............................................................................................................ 5
2.3.9 PTZ address scanning ................................................................................................ 5
2.3.10 Image magnification （ 10xZoom ） ......................................................................... 5
2.3.11 Video snapshot ......................................................................................................... 5
2.3.12 Video record ............................................................................................................ 5
2.3.13 Video playback ........................................................................................................ 5
2.3.14 Cable scan (optional function refer to the last page) ................................................. 6
2.3.15 Port flicker ............................................................................................................... 6
2.3.16 IP address scan ......................................................................................................... 6
2.3.17 Link monitor ............................................................................................................ 6
2.3.18 PING test ................................................................................................................. 6
2.3.19 POE tester ................................................................................................................ 6
2.3.20 Digital multimeter (optional function refer to the last page) .................................. 6
2.3.21 Optical Power Meter (optional function refer to the last page) ................................. 7
2.3.22 TDR Break-point and short-circuit measurement (optional function refer to the last
page) ................................................................................................................................... 7
2.3.23 Visual fault detector (optional function refer to the last page) .................................. 7
2.3.24 LED lamp ................................................................................................................ 7
2.3.25 F1 、 F2 User-defined shortcut keys .......................................................................... 7
2.4 Accessories .............................................................................................................................. 8
2.5 Front Panel .............................................................................................................................. 9
3 、 Operation ......................................................................................................................................... 13
3.1 Installing the Battery ............................................................................................................. 13
3.2 Instrument connection ........................................................................................................... 14
3.3 OSD Menu ............................................................................................................................ 14
3.3.1 PTZ controller .......................................................................................................... 15
3.3.2 Color-bar generator .................................................................................................. 18
3.3.3 Video setting ............................................................................................................ 19
3.3.4 PTZ address search .................................................................................................. 20
3.3.5 10x zoom image display and Video out ................................................................... 21
3.3.6 Photograph ............................................................................................................... 22
3.3.7 Video record ............................................................................................................ 22
3.3.8 Record playback ....................................................................................................... 22
3.3.9 Cable Scan （ optional ） ........................................................................................... 23
3.3.10 PING Test .............................................................................................................. 24
3.3.11 Cable tester ............................................................................................................ 25
3.3.12 Port flicker ............................................................................................................. 25
3.3.13 Link monitor .......................................................................................................... 26
3.3.14 IP address scan ....................................................................................................... 27
3.3.15 PoE tester ............................................................................................................... 27
3.3.16 Digital Multimeter （ optional ） ............................................................................. 28
3.3.17 Optical Power Meter （ optional ） .......................................................................... 36
3.3.18 Visual Fault Locator （ optional ） .......................................................................... 37
3.3.19 TDR Tester （ optional ） ........................................................................................ 37
3.3.20 Data monitor .......................................................................................................... 39
3.3.21 Time setting ........................................................................................................... 39
3.3.22 Device setting ........................................................................................................ 40
3.3.23 USB ....................................................................................................................... 41
3.4 DC12V 1A power output ....................................................................................................... 41
3.5 Audio input test ..................................................................................................................... 42
3.6 LED lamp .............................................................................................................................. 42
4 、 Specifications ................................................................................................................................... 42
4.1 General Specifications ........................................................................................................... 42
4.2 Multimeter specifications: ..................................................................................................... 45
4.3 Optical power meter specifications ........................................................................................ 48
4.4 Optional models .................................................................................................................... 48
CCTV
T
ester
User
’
s
CCTV
T
CCTV
CCTV T
1
Safety
1
Safety
1
1 、 Safety
Safety information
information
information
information
ester
T ester
ester User
User
User ’
Manual
’
s
Manual
’ s
s Manual
Manual
Notice
The tester is intended to use in compliance with the local rules of the electrical usage and avoid
to apply at the places which are inapplicable for the use of electrics such as hospital, gas station
etc.
To prevent the functional decline or failure, the product should not be sprinkled or damped.
The exposed part of the tester should not be touched by the dust and liquid.
During transportation and use, it is highly recommended to avoid the violent collision and
vibration of the tester, lest damaging components and causing failure.
Don ’ t leave the tester alone while charging and recharging. If the battery is found severely hot,
the tester should be powered off from the electric source at once. The tester should not be
charged over 8 hours.
Don ’ t use the tester where the humidity is high. Once the tester is damp, power off immediately
and move away other connected cables.
The tester should not be used in the environment with the flammable gas.
Do not disassembl e the instrument since no component inside can be repaired by the user. If the
disassembly is necessary indeed, please contact with the technician of our company.
The instrument should not be used under the environment with strong electromagnetic
interference.
Don ’ t touch the tester with wet hands or waterish things.
Don ’ t use the detergent to clean and the dry cloth is suggested to use. If the dirt is not easy to
remove, the soft cloth with water or neutral detergent can be used. But the cloth should be
tweaked sufficiently.
About
digital
About
About
About digital
Before using, you must select the right input jack, function and range.
Never exceed the protection limit values indicated in specifications for each range of
measurement.
When the meter is linked to a measurement circuit, do not touch unused terminals.
multimeter
digital
multimeter
digital multimeter
multimeter
1
1
1
1
CCTV
T
ester
User
’
s
CCTV
T
CCTV
CCTV T
Do not measure voltage if the voltage on the terminals exceeds 660V above earth ground.
At the manual range, when the value scale to be measured is unknown beforehand, set the range
selector at the highest position.
Always be careful when working with voltages above 60V DC or 4 0V AC, keep fingers behind
the probe barriers while measuring.
Never connect the meter with any voltage source while the function switch is in the current,
resistance, capacitance, diode, continuity, otherwise it will damage the meter.
Never perform capacitance measurements unless the capacitor to be measured has been
discharged fully.
Never measure any of resistance, capacitance, diode or continuity measurements on live circuits.
2
Introduction
2
Introduction
2
2 、 Introduction
Introduction
2.1
General
2.1
General
2.1
2.1 General
General
The new CCTV tester is developed for the On-Site installation and maintenance of IP camera ， analog
camera and network device, with V ideo display ,PTZ control, DC12v output power ,Audio test, Color
generator,RS 485 Data searching and C able testing, which are the same to the previous models. The
new developed functions include POE power supply testing, PING testing , IP address scan, Video
screen shot , Video record, I mage magnification , Port flicker, Cable search , LED lamp etc. The new
tester also has built in TDR cable testing, which is specialized designed for BNC cable testing in the
security monitoring system. This function can accurately measure BNC cable and network cable ’ s break
point and short-circuit location. The new tester designed with easy operation and portability makes it
simple for a cctv technician or install e r to install and maintain CCTV systems, improving work
efficiency by reducing time in the field.
ester
T ester
ester User
User
User ’
Manual
’
s
Manual
’ s
s Manual
Manual
2
2
2
2
CCTV
T
ester
User
’
s
CCTV
T
CCTV
CCTV T
2.2
Features
2.2
Features
2.2
2.2 Features
Features
English , Chinese and other languages optional
3.5 ” TFT-LCD, 480(RGB)x320
LED Lamp ， easy to operat e at night
Micro SD card moveable
User-defined shortcut keys （ F1 and F2 ）
LCD screen brightness/contrast/color Saturation adjustable
Automatically adapts and displays the video format of NTSC/PAL
10xzoom,video image can be magnified to view the details, easy to use
Video record and playback
Snapshot and save the current image as JPG file in the SD card
PING testing ， test IP camera or other network device s ’ ethernet port whether work normally ,
and the IP address whether right
IP address scan, quickly search the IP address for the connected IP camera and other
network devices
POE voltage measurement ， test the PoE switch ’ s voltage to IP cameras, wireless AP device
and other PD devices
Device Port flicker ， easy to find the connected PoE switch port by sending special signals,
the connected PoE port will flicker at special frequency.
Link monitor; check the setting IP address whether occupied .
TDR break point and short – circuit measurement( BNC cable, network cable etc )
PTZ address scan, search up the ID of PTZ camera.
Network cable and Telephone cable testing, display the sequence of connection and the NO
of the LAN cable
Support RS232/RS485/RS422 ， Rate 600 ～ 115200bps adjustable
Multi-protocol. Supports more than thirty PTZ protocols. Such as PELCO-P, PELCO-D,
SAMSUNG
ester
T ester
ester User
User
User ’
Manual
’
s
Manual
’ s
s Manual
Manual
3
3
3
3
CCTV
T
ester
User
’
s
CCTV
T
bar
bar
bar generator
ester
T ester
ester User
test
test
test
generator
generator
generator
CCTV
CCTV T
PTZ protocol analysis, control protocol command displays to check RS485 transmission
whether is normal, easy to find the fault device
PTZ control. Pan/tilts the P/T unit, zooms in/out the lens, adjusts the focus, aperture and
sets and the preset position
DC12V 1A power output for camera
Audio input test, test the audio signal from pickup devices
Visual fault locator , to test fiber ’ s bending and breakage
Lithium Ion Polymer Battery .The device employs advanced power control and protection
circuit. The device is high power-efficient, energy saving and environmental protection.
It can last 11 hours for normal use after charging for 4 -5 hours
2.3
Function
2.3
Function
2.3
2.3 Function
Function
2.3.1
2.3.1
2.3.1
2.3.1 Video
The new cctv tester ,built-in high definition 3.5 ” LCD-TFT 480 （ RGB ） x320
full-view display screen, easy and directly displays the camera image quality
Support PAL/NTSC
LCD screen brightness/Contrast/Color Saturation adjustable. Suitable for field construction and
maintenance work
2.3.2
2.3.2
2.3.2
2.3.2 Video
Test video signal strength attenuation, longer video signal cable will cause the image to be dim , and
reduce the image dynamic range, video signal is too strong, it will cause the virtual shadow, and reduce
the sharpness of the image.
It also can real-display the video level value, if out of range, notices will be display in the screen.
2.3.3
2.3.3
2.3.3
2.3.3 PTZ
Display the input video images. Pan/tilt the P/T unit and zoom in/ out the image. Setup the controlling
parameters like protocol, communication port, baud rate, PTZ ID, pan/tilt speed; set and call preset
position.
2.3.4
2.3.4
2.3.4
2.3.4 Enhanced
Video Generating, the PAL/NTSC multi-system color bar video generator (Eight-system switchable,
Video
Video
Video signal
Video
Video
Video signal
PTZ
PTZ
PTZ controller
Enhanced
Enhanced
Enhanced Color
signal
signal
signal testing
signal
signal
signal level
controller
controller
controller
Color
Color
Color bar
testing
testing
testing
level
level
level test
User
User ’
Manual
’
s
Manual
’ s
s Manual
Manual
4
4
4
4
CCTV
T
ester
User
’
s
CCTV
T
power
power
power
ester
T ester
ester User
10xZoom
10xZoom
10xZoom ）
CCTV
CCTV T
transmit/receive eight-system colorful imagines). By receiving the video color bar to test the video
channel whether transmit normally. And judge whether the color is different, because of the
transmission loss or interference, it suitable for Video transmission of the field tests, such as optical
video transmitter and receiver , video cable etc.
The new function color bar can test the image whether shift.
The color bar (red, green, blue, white, black) test the monitor whether have white or black dot etc.
2.3.5
2.3.5
2.3.5
2.3.5 DC12V
Power the camera with DC12V (1A) power output from the tester. It is helpful for demo and testing
when the power supply is not available .
2.3.6
2.3.6
2.3.6
2.3.6 Audio
Test the audio input from pickup devices. Connect the tester and pickup device with the audio cable.
2.3.7
2.3.7
2.3.7
2.3.7 Cable
Test LAN cable or telephone cable.
Connect LAN cable or telephone cable with the CCTV tester and cable tester. And then the connecting
status, cable type and the sequence of wires will be displayed, as well as the serial number of the cable
tester kit.
2.3.8
2.3.8
2.3.8
2.3.8 PTZ
Search the Control protocol code from Multifunction keyboard or DVR by RS485 /RS232 interface, test
the PTZ control command data whether received anomaly and RS485/RS232 data transmission.
2.3.9
2.3.9
2.3.9
2.3.9 PTZ
Search up the ID of PTZ camera. Help the engineer search the speed dome address quickly.
2.3.10
2.3.10
2.3.10
2.3.10 Image
Set image 10x zoom, can view and display the details by 1x 、 2x 、 3x 、 4x 、 5x 、 6x - 10X zoom in the
monitor and tester.
2.3.11
2.3.11
2.3.11
2.3.11 Video
Capture the video image and save the current video frames as JPEG file
DC12V
DC12V
DC12V 1A
Audio
Audio
Audio testing
Cable
Cable
Cable tester
PTZ
PTZ
PTZ controller
Screen displays 16 hexadecimal codes such as
PELCO-P ： A0 00 （ Add ） xx xxxxxx AF xx
PELCO-D ： FF 01 （ A dd ） xx xxxxxxxx
PTZ
PTZ
PTZ address
1A
output
1A
output
1A output
output power
testing
testing
testing
tester
tester
tester
controller
controller
controller
address
address
address scanning
Image
Image
Image magnification
Video
Video
Video snapshot
scanning
scanning
scanning
magnification
magnification
magnification （ 10xZoom
snapshot
snapshot
snapshot
User
User ’
Manual
’
s
Manual
’ s
s Manual
Manual
5
5
5
5
CCTV
CCTV
CCTV
CCTV T
T
ester
T
ester
T ester
ester User
User
User
User ’
’
s
Manual
’
s
Manual
’ s
s Manual
Manual
2.3.12
2.3.12
2.3.12
2.3.12 Video
Record and save the current video in the SD card
2.3.13
2.3.13
2.3.13
2.3.13 Video
Video image and record files are saved in the SD card. Storage file directory can be created according
to the date
2.3.14
2.3.14
2.3.14
2.3.14 Cable
Send the specific signal, easy to find the connected cable.
2.3.15
2.3.15
2.3.15
2.3.15 Port
The tester will send special signals to make the connected PO E port flicker at special frequency, which
will enable the installers to easily and quickly find the connected ethernet cable. This function can
prevent mistakenly insertion or disconnection non-corresponding cable to artificially interrupt network
connection.
2.3.16
2.3.16
2.3.16
2.3.16 IP
In digital IP surveillance applications, if IP camera ’ s IP address is not clear or forgotten; the device
cannot be used . IP address scan can quickly search the connected IP camera or other network device ’ s
IP address.
2.3.17
2.3.17
2.3.17
2.3.17 Link
To add an IP camera or other network device to the current network group, the new IP address must not
be occupied, otherwise it will cause IP conflicts and stop the equipment normal working. Link monitor
can check if the new setting IP address is occupied.
2.3.18
2.3.18
2.3.18
2.3.18 PING
PING is the most conventional network debugging tools; It is used for testing if the connected IP
camera or other network equipment ’ s ethernet port is working normally and the IP address is correct.
2.3.19
2.3.19
2.3.19
2.3.19 P
It can test the PoE voltage when the POE switch is supplying the POE power to IP camera. It can
clearly display the power+ and power- on the ethernet cable pins, each cable pin ’ s voltage and the
failure connection of cable pin series numbers.
2.3.20
2.3.20
2.3.20
2.3.20 D
page
page
page
page )
)
)
)
Video
Video
Video r
Video
Video
Video playback
Cable
Cable
Cable scan
Port
Port
Port flicker
IP
IP
IP address
Link
Link
Link monitor
PING
PING
PING test
P
O
E
P
O
E
P O
O E
E test
D
igital
D
igital
D igital
igital multimeter
flicker
flicker
flicker
address
address
address scan
monitor
monitor
monitor
test
test
test
test
test
test er
r
r
r ecord
playback
playback
playback
scan
scan
scan (
ecord
ecord
ecord
(
optional
(
optional
( optional
optional function
scan
scan
scan
er
er
er
multimeter
multimeter
multimeter (
function
function
function refer
(
optional
(
optional
( optional
optional function
refer
refer
refer to
function
function
function refer
to
to
to the
refer
refer
refer to
the
last
the
the last
page
last
page
last page
page )
to
the
to
to the
last
the
last
the last
last
)
)
)
6
6
6
6
CCTV
T
ester
User
’
s
CCTV
T
T ester
Meter
Meter
Meter (
and
and
and short-circuit
locator
locator
locator (
ester
ester User
(
optional
(
optional
( optional
optional function
short-circuit
short-circuit
short-circuit measurement
to
the
to
the
to the
the last
(
(
( optional
shortcut
shortcut
shortcut keys
CCTV
CCTV T
CCTV Tester built in highly stable and reliable 33/4 digit (6600) digital multimeter. It is used for the
DC and AC voltage measurement , AC and DC current measurement , Resistance measurement,
Continuity test, Diode measurements, Capacitance measurement, Auto/ Manual measuring range
switching, relative value measurement and locking . It is easy operation and professionally accurate.
2.3.21
2.3.21
2.3.21
2.3.21 O
last
last
last
last page
The New tester adopts the most advanced handheld instrument specific integrated chip , a chieve
ultra-low power operation, with the 3.5 TFT-LCD High-definition screen display ， f ive wavelength
calibration points 1625nm 、 1550nm 、 1490nm 、 1310nm 、 1300nm 、 850nm.Linear or nonlinear
optical power display, it can measure the optical power value, and also be used for Relative
measurement of optical fiber link loss. It is necessary tool for fibre-optic communication , cable
television system and security system maintenance .
2.3.2
2.3.2
2.3.2
2.3.2 2
(
optional
(
optional
(
( optional
optional function
New function: TDR cable testing, accurately measure BNC cable, network cable, control cable
break-point and short-circuits location. It improves working efficiency.
2.3.2
2.3.2
2.3.2
2.3.2 3
last
last
last
last page
Visual Fault Locator with 650nm wavelength can emit red laser sources to test multi-mode and single
mode fiber ’ s bending and breakage, and Continuous light-emitting and 1HZ, 2Hz modulating light
output. It is indispensable tool in fiber project constructing, fiber net-work maintaining, optical
component manufacture and research .
2.3.2
2.3.2
2.3.2
2.3.2 4
It is useful for the Engineer to install and maintain security system at night. LED On /Off pressing
button , easy operation.
2.3.2
2.3.2
2.3.2
2.3.2 5
The user-defined shortcut key is designed for improving the efficiency for the engineer, anytime press,
easy to operate.
page
page
page )
2
2
2 TDR
3
3
3 Visual
page
page
page )
4
4
4 LED
5
5
5 F1
O
ptical
O
ptical
O ptical
ptical Power
TDR
TDR
TDR b
Visual
Visual
Visual fault
LED
LED
LED lamp
F1
F1
F1 、 F2
)
)
)
b
reak-point
b
reak-point
b reak-point
reak-point and
function
function
function refer
)
)
)
lamp
lamp
lamp
F2
F2
F2 User-defined
Power
Power
Power Meter
fault
fault
fault locator
User-defined
User-defined
User-defined shortcut
refer
refer
refer to
User
User ’
optional
optional
optional function
Manual
’
s
Manual
’ s
s Manual
Manual
last
last
last page
keys
keys
keys
function
function
function refer
page
page
page )
function
function
function refer
refer
refer
refer to
measurement
measurement
measurement
)
)
)
refer
refer
refer to
to
the
to
the
to the
the
to
the
to
the
to the
the
7
7
7
7
CCTV
T
ester
User
’
s
CCTV
T
CCTV
CCTV T
2.4
Accessories
2.4
Accessories
2.4
2.4 Accessories
Accessories
1). CCTV tester
2). Power Supply DC5V 1.2 ～ 1.5A （ with USB cable ）
3). Cable test box or wire tracer
4). Lithium Ion Polymer Battery （ 3.7V DC 3000mAh ）
5). BNC cable
6). RS485 cable
7) SC, ST connector (Only for the optical power meter models)
8) Multimeter test leads one pair of red and black (only for the Multimeter models)
9). Power cable
10). Audio cable
11). TDR alligator clamp （ only for TDR models ）
12). Safety cord
13). Tool bag
14). Instruction Manual
ester
T ester
ester User
User
User ’
Manual
’
s
Manual
’ s
s Manual
Manual
8
8
8
8
2.5
Front
2.5
Front
2.5
2.5 Front
Front Panel
Panel
Panel
Panel
CCTV
CCTV
CCTV
CCTV T
T
ester
T
ester
T ester
ester User
User
User
User ’
’
s
Manual
’
s
Manual
’ s
s Manual
Manual
9
9
9
9
CCTV
T
ester
User
’
s
CCTV
T
CCTV
CCTV T
1 OSD menu
2
3 The data-transmission indicator: it lights red while the data is being transmitted
4 The data-reception indicator: it lights red while the data is being received.
5 The power indicator: it lights green while the tester is powered on.
6 Set key, press it to enter sub-menu to set the parameters of functions.
7
8 Confirm/Open : Confirm the setting of parameters ； open or enlarge the aperture 。
9
10
11 User-defined key （ User setting function, the default is “ PTZ controller ” ）
12 LED Lamp
13
14
15
16 Leftward: Enter the sub-menu or select the parameter whose value will be changed.
The charge indicator: it lights red while the battery is being charged. As the charging
is complete, the indicator turns off automatically.
Press more than 2 seconds, turn on or off the device ,short press to turn on or off the
menu display
Return/Close : Return or cancel while setting parameters of the menu, close or
decrease the aperture
Upward: Select the item which will be set or add the value of the parameter. Tilt the
PTZ upward.
Rightward ， Enter the sub-menu or select the parameter whose value will be changed.
Add the value of the parameter. Pan the PTZ right.
Voltage, current, resistance and capacitance measuring, continuity testing, diode
testing.
Downward: Select the item which will be set or reduce the value of the parameter.
Tilt the PTZ downward.
ester
T ester
ester User
User
User ’
Manual
’
s
Manual
’ s
s Manual
Manual
10
10
10
10
CCTV
T
ester
T
ester
T ester
ester User
User
User
User ’
CCTV
CCTV
CCTV T
Reduce the value of the parameter. Pan the PTZ left.
17 Video record
18 Snapshot （ capture video image ）
19 10xzoom the image display and video out
20 WIDE: zoom in the image
21 Near focus: Focus the image nearby.
22 Far focus: Focus the image faraway.
23 Menu key
24 TELE: zoom out the image
’
s
Manual
’
s
Manual
’ s
s Manual
Manual
11
11
11
11
CCTV
CCTV
CCTV
CCTV T
T
ester
T
ester
T ester
ester User
User
User
User ’
’
s
Manual
’
s
Manual
’ s
s Manual
Manual
Without TDR test ing
26 Video input (BNC input interface): Inputs the video
27 Video output (BNC output interface): Outputs the video
28 TDR cable break point and short circuit test
29 Output DC12V1A power, for provisional DC test supply
30 RS232 interface: RS232 communication for the PTZ
31 LED lamp
32 R S485/422 Interface: RS485/RS422 communication for the PTZ
33 Network cable /Telephone cable interface test
34 USB data /charge interface
35 Moveable MicroSD card
36 Ethernet power supply output/Network testing interface
37 Ethernet power supply input interface
38 Audio input: test the pickup and other audio equipments on the front-end
With TDR test ing
12
12
12
12
CCTV
T
ester
User
’
s
CCTV
T
T ester
Battery
Battery
Battery
adaptor
adaptor
adaptor and
ester
ester User
and
connected
and
connected
and connected
connected cable
CCTV
CCTV T
39 Reset the default settings of parameters.
40 Optical power meter interface ( Optional )
41 Visual Fault Locator with 650nm wavelength , can emit red laser sources to test
multi-mode and single mode fiber ’ s bending and breakage
3
Operation
3
Operation
3
3 、 Operation
Operation
3.1
Installing
3.1
Installing
3.1
3.1 Installing
Installing the
The tester has built-in lithium ion polymer rechargeable battery. The battery cable inside battery
cabin should be disconnected for safety during transportation!
Prior to the use of the instrument, the battery cables inside the battery cabin should be well
connected.
Usually it does n ’ t need to disconnect the cable at the normal use
Pressing key continuously can power on or off the tester.
Notice
Pls
use
Pls
Pls use
use
use the
the
the
the original
Notice
Notice
Notice ： Pls
At the first time of use, the batteries should be completely exhausted and then recharged for 4 or
5 hours.
The Charge Indicator lights red when charging the battery, the charge indicator turns off
automatically when the charging is completed.
the
the
the Battery
original
original
original adaptor
User
User ’
Manual
’
s
Manual
’ s
s Manual
Manual
cable
cable
cable of
of
the
of
the
of the
the device
device
device
device
Notice: When the Charge Indicator turns off, the battery is approximately 90%
charged. The charging time can be extended for about 1 hour and the charging time within 8
hours will not damage the battery.
Press the RESET key at the left of the instrument to restore the default settings when the
instrument works abnormally.
Multimeter: the red and black multimeter pen must insert the corresponding port.
13
13
13
13
3.2
Instrument
3.2
Instrument
3.2
3.2 Instrument
Instrument connection
CCTV
T
CCTV
CCTV
CCTV T
connection
connection
connection
ester
T
ester
T ester
ester User
User
User
User ’
’
s
Manual
’
s
Manual
’ s
s Manual
Manual
.
.
The camera or dome video output is connected to CCTV Tester VIDEO IN ， the image display
⑴ .
.
on the tester .
.
.
CCTV Tester “ VIDEO OUT ” interface connect to the Video input of monitor and optical
⑵ .
.
video transmitter and receiver , the image display on the tester and monitor
.
.
⑶ .
. Connect the camera or the speed dome RS485 controller cable to the tester RS485
interface ,(Note positive and negative connection of the cable).Support R S 232 PTZ
controller ,connect the RS232cable to RS232 interface of the tester
14
14
14
14
CCTV
T
ester
User
’
s
CCTV
T
CCTV
CCTV T
3.3
OSD
3.3
3.3
3.3 OSD
Press the key to turn on.
Press the key again to turn off, also can set time off
Enter the menu ,choose one function to enter , short press the key ,Close the menu bar at
Press the key to enter the menu ， Continuously press quickly switch to the
In various functional mode, press the key Set the various parameter values
When turn it on, press the key , to enter the function menu, continuously press the
Press the key to switch the menu ， the square ,different square means
Press the key select the different function icon, then press the key to enter
Menu
OSD
Menu
OSD Menu
Menu
the top of the screen, full screen display, press it again, turn it on
desired function menu . Anytime, press this key to enter the menu.
key , select different function, and press the key to enter.
different interface
ester
T ester
ester User
User
User ’
Manual
’
s
Manual
’ s
s Manual
Manual
First page menu Second page menu Third page menu
3.3.1
3.3.1
3.3.1
3.3.1 PTZ
Display the input video images. Press the key to enter the menus and set Parameter .Pan/tilt
the P/T unit and zoom in/ out the image. Setup the controlling parameters like protocol, communication
port, baud rate, PTZ ID, pan/tilt speed; set and call preset position.
Display the input image; press the key closed the top
menu, display full screen image
Enter PTZ controller, if no video input, the screen display “ No
video “ .
PTZ
controller
PTZ
controller
PTZ controller
controller
15
15
15
15
CCTV
T
ester
User
’
s
CCTV
T
CCTV
CCTV T
PTZ
controller
PTZ
controller
PTZ
PTZ controller
controller parameter
In the “ PTZ CONTROLLER ” mode （ as shown above ） ， press the key to enter the parameter
setting .
press the key 、 ,move the yellow cursor to select
Press the key or , change the parameter values. Then press the key to save and
return.
If no change, Press the key to return setting, and then press the key return the PTZ
controller function.
A.
Protocol
A.
Protocol
A.
A. Protocol
Protocol
Use the up and down arrow keys to move the yellow cursor to
protocol
protocol
the
"
protocol
protocol", set corresponding Protocol ,Support more than
thirty PTZ protocols. Such as Pelco-D 、 Samsung 、 Yaan 、 LiLin
CSR600 、 Panasonic 、 Sony-EVI etc.
B.
Port
B.
Port
B.
B. Port
Port
parameter
parameter
parameter setting
setting
setting
setting
Move the yellow cursor to “ port ",
(RS232/422/485)
C.
Baud
C.
Baud
C.
C. Baud
Baud
Move the yellow cursor to"Baud ” ， Select the baud rate according to baud rate of the PTZ
camera.( 600/1200/2400/4800/9600/19200 /57600/115200 bps)
D.
Address
D.
Address
D.
D. Address
Address
Set the ID according the ID of PTZ camera (0~254), the setting address data must be consistent the
speed dome address.
E.
Pan
speed:
E.
Pan
E.
E. Pan
Pan speed:
F.
Tilt
F.
Tilt
F.
F. Tilt
Tilt speed:
G.
Set
G.
Set
G.
G. Set
Set preset
Move the yellow cursor to “ SET PS ” ， set and save preset position number(1~128),Press the key
Set
speed:
Set
speed: Set
Set the pan speed of PTZ camera (0~63)
speed:
speed:
speed: Set the tilt speed of PTZ camera (0~63)
preset
position
(Set
preset
position
preset position
position (Set
(Set
(Set PS)
PS)
PS)
PS)
ester
T ester
ester User
Select the communication port for the PTZ camera controlling
User
User ’
Manual
’
s
Manual
’ s
s Manual
Manual
、
16
16
16
16
CCTV
T
ester
User
’
s
CCTV
T
CCTV
CCTV T
to accelerate the value changing, then press the key to save, Press to quit.
H.
Call
the
preset
position
(Go
H.
Call
the
preset
H.
H. Call
Call the
the preset
Move the yellow cursor to “ Set PS ” , then Setup preset position (1~128),
Press key or to accelerate the value changing.
Press the key to complete preset position setting or press return key to to quit.
Call some special preset number ， can call the dome camera menu
Check and set the protocols, address, interface and baud, must be the same as the dome camera, then
can test and control.
After setting the parameter, the tester can control the PTZ and lens
Press the key to control the PTZ direction of rotation
Press the key or to switch on or turn off the aperture.
Press the key or ,adjust the focus manually
Press the key or ， manually adjust the zoom
1)
Set
1)
Set
1)
1) Set
Set and
Set
PS
Set
PS
Set
Set PS
PS
A. P/T/Z the camera to desired position.
B. Press the key to enter the PTZ controller submenu. Press the key Move the
yellow cursor to “ Set PS ” , Press the key to select the preset position number.
Press enter key to complete preset position setting or preset return the key to give up set
position setting.
preset position
and
and
and go
position
position (Go
go
PS
go
PS
go PS
PS
(Go
(Go ps)
ps)
ps)
ps)
ester
T ester
ester User
User
User ’
Manual
’
s
Manual
’ s
s Manual
Manual
Go
PS:
Go
PS:
Go
Go PS:
PS:
Call the preset position. ( 1 ~128) The PTZ camera will go to the desired preset position.
In “ PTZ Controller" mode,Press the key to t enter PTZ controller submenu. Press the key
Move the yellow cursor to “ GO ps ” , to select the preset position number. Then press the enter key
to complete preset position setting or preset RETURN key to give up preset position setting.
Camera moves to the prese t position immediately, Lens zoom, focus and iris is automatically changed
17
17
17
17
CCTV
T
ester
User
’
s
CCTV
T
CCTV
CCTV T
to the preset parameters, preset the camera image displayed on the monitor.
Tips
Tips
Tips
Tips ： Preset position setting is saved in the domes. (Preset position can be set depending on the dome )
2)
Menu
of
of
of
of Dome
only)
only)
only)
dome
of
dome
of dome
dome
Dome
Dome
Dome (For
(For
(For
(For
2)
Menu
2)
2) Menu
Menu of
Different dome camera factory control system be used different preset position, pls refer to the dome
camera manual. The provided dome camera enter the the menu by calling preset position 64 , t his
example is for reference only
a. Press the key to enter PTZ controller submenu
b.Press the key , select preset position 64
c. Press the key Enter the main menu of the PTZ camera
OSD
Menu
OSD
Menu
OSD
OSD Menu
Menu of
Reference
Reference
Reference
Reference only)
ester
T ester
ester User
User
User ’
Manual
’
s
Manual
’ s
s Manual
Manual
After Calling the dome camera menu , Users can select different function through the arrow keys , the
dome camera menu operation refer to the manual.
3.3.2
3.3.2
3.3.2
3.3.2 Color
Press the key to enter the menu
Press the key to select the bar , and then press the key to enter
Color
Color
Color -
-
bar
generator
-
bar
generator
- bar
bar generator
generator
18
18
18
18
CCTV
T
ester
User
’
s
CCTV
T
CCTV
CCTV T
Test the Color - bar generator, support global PAL / NTSC standard color bar of different output formats
Press the key or ,move the cursor to “ Format ” 、 “ LCD display select ” 、 “ Type ” .select
“ Format ” ， the tester send the color bars from the “ Video out ” port .Press the key or to switching
the video output formats. when select “ LCD ” ， press the key or switching the display content.
Press the to turn off the menu, sending or receiving image to display full screen ； Press it again;
display the Color – bar generator menu.
In the “ color bar generator ” mode, output different standard color bar and received by “ Video IN ”
port ， Display the video input and output .
This feature is available for test monitoring transmission channels, such as optical video transmitter and
receiver , video cables, etc. the “ Video out “ port connect the sending port of the optical video
transmitter , the “ Video in “ port connect the receiving port
Image receiving ： connect the Video OUT port to the Video in port, Video generator send the color bars,
to choose the direction key change “ the display select “ for the “ Video input ” , The screen is in the image
receiving state, if cannot receive the image ,the screen display “ NO VIDEO “ , if received , display the
sending and receiving consistent color bar.
Application
Application
Application
Application ：
A
A
A
A . When maintain the dome camera, send the image to the monitoring center, If the monitoring center
can receive the image, it means that the Video transmission channel normal, in addition, the monitor
center can judge the image quality through the received color bar.
B
B
B
B .Test the optical video transmitter and Video cable, sending and receiving color bar by itself, check
the transmission equipment or cable whether normal.
c.
c.
c.
c. Send the pure color bar (such as white and black color) ， to test the monitor whether has bright or
black dots
D
D
D
D .Send video signal image ， test received image whether shift.
ester
T ester
ester User
User
User ’
Manual
’
s
Manual
’ s
s Manual
Manual
19
19
19
19
CCTV
CCTV
CCTV
CCTV T
T
ester
T
ester
T ester
ester User
User
User
User ’
’
s
Manual
’
s
Manual
’ s
s Manual
Manual
3.3.3
3.3.3
3.3.3
3.3.3 Video
Press to the menu , press to enter.
LCD brightness, contrast, color saturation can be adjusted.
The CCTV tester auto displays the format (PAL/NTSC) of video input, and analysis the input video
The Video Level should be within the indicated range. Levels that are too low will result in a dim
Depending on the type of camera connected to the CCTV tester, the Video “ Format: “ will automatically
change between NTSC and PAL, and the Video Level will automatically change between IRE (Institute
of Radio Engineers) and mV. NTSC signals measured in IRE units, PAL signals measured in mV.
3.3.4
3.3.4
3.3.4
3.3.4 PTZ
Press to select , press to enter.
Video
Video
Video setting
signal level.
picture with reduced dynamic range. A Video Level that is too high will result in washed out
pictures with decreased.
PTZ
PTZ
PTZ address
address
address
address search
setting
setting
setting
search
search
search
20
20
20
20
CCTV
T
ester
User
’
s
CCTV
T
CCTV
CCTV T
Note
Note
Note
Note ： Please isolate the PTZ camera with other PTZ cameras before searching up. Otherwise all
the PTZ cameras in the same system will pan at the same time.
Press to select , and then press to enter (as follow picture). Select to “ Address
search ” , press to select ON or OFF, then Press to save. The PTZ address search
function displays in the main menu.
（ Note ： This function need to reset after each time turn off. ）
Press key to set: protocol, communication port, communication rate, make them the same as
PTZ camera.
Press button, the tester will search up the ID quickly and continuously. When the ID is searched,
the PTZ camera will pan right. At this time, please press to stop searching up.
ester
T ester
ester User
User
User ’
Manual
’
s
Manual
’ s
s Manual
Manual
Press the key manual single-step decreasing button, the tester will search up the ID step by step.
When the ID is searched, the PTZ camera will stop panning.
Press button, the tester will search up the ID quickly and continuously. When the ID is searched,
the PTZ camera will pan left. At this time, please press to stop searching up. Press
manual single-step incremental button ， the tester will search up the ID step by step. When the ID
is searched, the PTZ camera will stop panning.
Manual
search
Manual
Manual
Manual search
when the address found. Press the direction control button to adjust Speed Dome Camera.
Press button to quit.
address:
search
address:
search address:
address: Press or to search the address gradually, the image will flash
21
21
21
21
CCTV
CCTV
CCTV
CCTV T
T
ester
T
ester
T ester
ester User
User
User
User ’
’
s
Manual
’
s
Manual
’ s
s Manual
Manual
3.3.5
3.3.5
3.3.5
3.3.5 10x
While video input, press to 10x zoom, and press the button to zoom in the image, press
to zoom out the image. Press to see the details. Press to quit.
Set image 10x zoom, can view and display the local details by 1x 、 2x 、 3x 、 4x 、 5x 、 6x -10X zoom in
the monitor and tester.
3.3.6
3.3.6
3.3.6
3.3.6 Photograph
While video in, Press the key to save the current video frame in the SD card as JPEG file. Set
storage file according to the date, it ’ s convenient to check .the tester automatically checks whether have
SD card when photograph. If no SD card, shown “ no SD Card ” on the the screen.
3.3.7
3.3.7
3.3.7
3.3.7 Video
While video in, press several seconds, the icon is flicking on the top left, me ans the video record
is under working and saving the video in the SD card as AVI format. Press the flicker icons
disappears and stop working. Set storage file according to the date, it ’ s convenient to check.
Note:
Note:
Note:
Note: press
10x
10x
10x zoom
Photograph
Photograph
Photograph
Video
Video
Video record
press
press
press the
zoom
zoom
zoom image
record
record
record
the
button
the
button
the button
button several
image
image
image display
several
several
several seconds,
display
display
display and
seconds,
seconds,
seconds, and
and
and
and Video
and
start
and
start
and start
start to
Video
Video
Video out
to
to
to the
the
the
the video
out
out
out
video
record.
video
record.
video record.
record.
3.3.8
3.3.8
3.3.8
3.3.8 Record
Press to select , press to enter, the latest photograph or video record file display on
the screen.
Record
Record
Record playback
playback
playback
playback
22
22
22
22
CCTV
T
ester
User
’
s
CCTV
T
CCTV
CCTV T
As the above picture, the photograph file with the icon , and the video record file with the icon
on the top right corner. Press to start and stop video playback and, press to quit.
See the above image, the 3/0008 in the image means total 8 screenshot and video file, and the current
file is the third.
press to quit the latest storage image,
Press to choose the files.
Then press to shown all the storage files, press to choose the files. Press
to enter the files, press to choose the image.
3.3.
9
3.3.
3.3.
3.3. 9
Connect the cable to the UTP port or the CABLE SCAN (VIDEO OUT) port on the top.
Press to select , then press to enter, press to choose the audio type.
Cable
9
Cable
9 Cable
Cable Scan
Scan
Scan
Scan （ optional
optional
optional
optional ）
ester
T ester
ester User
User
User ’
Manual
’
s
Manual
’ s
s Manual
Manual
Turn on the cable scan; use the copper pin to search, the cable with loudest voice means it is connected
with the tester. Four Audio types can choose. LED lamp is convenient to work in dark or at night. Press
the button (+ - ) to adjust the volume,
use two batteries (size AAA)
Application
Application
Application
Application
23
23
23
23
CCTV
T
ester
User
’
s
CCTV
T
CCTV
CCTV T
It ’ s convenient for people to find out the other
end of the cable in security maintenance and network engineering.
While searching BNC cable, connect one port of the alligator clips to the copper core or copper net of
the BNC cable, the other one to connect the earth wire (barred windows).
Note
The
battery
of
the
Note
The
Note
Note ： The
Note
Note
Note
Note ： While
3.3.
10
3.3.
10
3.3.
3.3. 10
10 PING
Connect the cable to the LAN port, press to select , and then press to enter. Press
parameter.
battery
The battery
battery of
negative
pole
negative
pole
negative
negative pole
pole -
While
receive
While
receive
While receive
receive the
and
make
and
make
and
and make
make some
PING
Test
PING
Test
PING Test
Test
to adjust the IP address, Packet Size, Timeout, TTL, Count. Press to adjust the
wire
of
the
wire
of the
the wire
wire tracer
-
,
or
damage
-
,
or
damage
- ,
, or
or damage
damage the
the
audio
the
audio
the audio
audio signal
some
noise.
some
noise.
some noise.
noise.
ester
T ester
ester User
tracer
must
tracer
must
tracer must
must according
the
tester.
the
tester.
the tester.
tester.
signal
from
signal
from
signal from
from the
User
’
s
User ’
’ s
s Manual
according
according
according to
the
tester,
the
tester,
the tester,
tester, it
Manual
Manual
Manual
to
corresponding
to
corresponding
to corresponding
corresponding positive
it
will
be
influenced
it
will
be
influenced
it will
will be
be influenced
influenced by
positive
positive
positive pole
by
the
by
the
by the
the other
pole
+
pole
+
pole +
+ and
other
other
other signal
and
and
and
signal
signal
signal
If IP camera or other ethernet equipment is not connected to the tester, “ connect fail “ display on the
screen. The sending and receiving packet amount is 0, the success rate is 0%. Press to restart the
Ping testing after the IP equipment is well connected. If the IP address is correct, the sending and
receiving packet amount will be consistent; the success rate will be 100%.
Application
Application
Application
Application
PING testing is the most conventional network debugging tools .
It is used for testing if the connected IP camera or other network
24
24
24
24
CCTV
T
ester
User
’
s
CCTV
T
be
be
be used
T ester
used
used
used with
ester
ester User
with
the
with
the
with the
the wire
CCTV
CCTV T
equipment ’ s ethernet port is working normally and the IP address is correct.
It ’ s normal that the first data packet will be lost when start the PING testing .
3.3.
11
11
11 Cable
if
if
if No
No
cable
No
cable
No cable
cable tester
Cable
Cable
Cable tester
3.3.
3.3.
3.3. 11
Press to menu , press to enter.
Test LAN cable or telephone cable.
Connect LAN cable or telephone cable with the CCTV tester and cable tester. And then the connecting
status, cable type and the sequence of wires will be displayed, as well as the serial number of the cable
tester kit.
Note:
Note:
Note:
Note: if
tester
tester
tester
tester
box,
tester
box,
tester box,
box, it
it
can
it
can
it can
can be
User
User ’
wire
wire
wire tracker
Manual
’
s
Manual
’ s
s Manual
Manual
tracker
tracker
tracker
3.3.
12
Port
3.3.
12
3.3.
3.3. 12
12 Port
Press to select , and then press to enter. Press to start, the tester send the
signal, to make the connected PoE port flicker at special frequency. Press to stop, and press
to quit.
flicker
Port
flicker
Port flicker
flicker
25
25
25
25
CCTV
T
ester
User
’
s
CCTV
T
CCTV
CCTV T
If the tester and PoE port are not well connected, there won ’ t be any change on the PoE port.
Application
Application
Application
Application
The tester will send special signals to make the connected PoE port flicker at special frequency, which
will enable the installers to easily and quickly find the connected ethernet cable. This function can
prevent mistakenly insertion or disconnection non-corresponding cable to artificially interrupt network
connection.
3.3.1
3.3.1
3.3.1
3.3.1 3
Press to select , and then press to enter.
：
3
Link
3
3 Link
monitor
Link
monitor
Link monitor
monitor
ester
T ester
ester User
User
User ’
Manual
’
s
Manual
’ s
s Manual
Manual
Add the IP address, make sure the network segment and the setting IP address are consistent, choose
“ start ” , and press to link monitor. If the status is “√” , means the IP address is occupied, if the
status is “×” , means the IP address is available
Application
Application
Application
Application
Add an IP camera or other network device to the current network group, the new IP address must not be
occupied, otherwise it will cause IP conflicts and stop the equipment normal working. Link monitor can
check if the new setting IP address is occupied.
：
26
26
26
26
CCTV
T
ester
User
’
s
CCTV
T
CCTV
CCTV T
3.3.1
4
IP
3.3.1
3.3.1
3.3.1 4
Connect the cable to the LAN port, press to select press to enter. Press to
“ Set IP ” , press to set the local IP address, the network segment and the network devices must be
consistent. After setting, move the cursor to “ Start ” , press to scan the IP camera or other network
equipment address.
3.3.1
3.3.1
3.3.1
3.3.1 5
Press to select , and then press to enter. Connect the cable to the power
supply equipment ’ s POE port and the tester ’ s PSE IN port. Connect IP camera or wireless AP
equipment connect tester ’ s LAN port, the POE voltage and the cable ’ s pin connection status show on
the screen.
address
4
IP
address
4 IP
IP address
address scan
5
P
O
E
5
5 P
tester
P
O
E
tester
P O
O E
E tester
tester
scan
scan
scan
ester
T ester
ester User
User
User ’
Manual
’
s
Manual
’ s
s Manual
Manual
Note
Note
Note
Note ： the
connected
connected
connected
connected to
connected
connected
connected
connected to
Pl
S
do
not
Pl
S
do
not
Pl
Pl S
S do
do not
not connect
tester.
tester.
tester.
tester.
the
Poe
the
Poe
the Poe
Poe power
to
to
to the
to
to
to the
connect
connect
connect POE
power
power
power supply
the
P
SE
the
P
SE
the P
P SE
SE IN
the
LAN
the
LAN
the LAN
LAN port,
supply
supply
supply equipment(
IN
port,
IN
port,
IN port,
port, the
port,
then
port,
then
port, then
then it
POE
power
POE
power
POE power
power supply
equipment(
equipment(
equipment( POE
the
powered
the
powered
the powered
powered device
it
measure
it
measure
it measure
measure the
supply
port
supply
port
supply port
port to
POE
Switch,
POE
Switch,
POE Switch,
Switch, PSE
device
such
device
such
device such
such as
the
voltage
the
voltage
the voltage
voltage correctl
to
the
UTP/SCAN
to
the
UTP/SCAN
to the
the UTP/SCAN
UTP/SCAN port,
27
27
27
27
PSE
power
PSE
power
PSE power
power supply
as
IP
camera
as
IP
camera
as IP
IP camera
camera or
correctl
correctl
correctl y.
supply
supply
supply equipment)
or
wireless
or
wireless
or wireless
wireless AP
y.
y.
y.
port,
otherwise
port,
otherwise
port, otherwise
otherwise it
equipment)
equipment)
equipment) must
it
it
it will
AP
AP
AP must
will
will
will damage
must
must
must be
must
must
must be
damage
damage
damage the
be
be
be
be
be
be
the
the
the
CCTV
CCTV
CCTV
CCTV T
T
ester
T
ester
T ester
ester User
User
User
User ’
’
s
Manual
’
s
Manual
’ s
s Manual
Manual
3.3.16
3.3.16
3.3.16
3.3.16 Digital
To press to select , press to enter
1)
1)
1)
1) Function
2)
2)
2)
2) SYMBOLS
Ω ：
Digital
Digital
Digital Multimeter
Function
Function
Function Button
SYMBOLS
SYMBOLS
SYMBOLS ：
U
：
A
：
Button
Button
Button ：
： Auto range ： Data hold ： Relative measuring
： Function select ： Manual range
DC Voltage Measuring U~：AC Voltage Measuring
DC Current Measuring A~：AC Current Measuring
Resistance Measuring
Diode Testing
：
Multimeter
Multimeter
Multimeter （ optional
optional
optional
optional ）
Continuity Testing
：
Capacitance Measuring
：
AC/DC Voltage and current measurement state display
Auto- range The Multimeter auto adjust the range by input signal or tested components
Data hold Hold data
Relative
measurement
10A socket In 10A current measurement state ,indicate use 10A socket
Over range
Display the relative measurement value
Press the key to change display state
The current measurement value over the range, if in the Auto range state, to
switch Auto.
28
28
28
28
CCTV
T
ester
User
’
s
CCTV
T
CCTV
CCTV T
3)
OPERATING
3)
OPERATING
3)
3) OPERATING
OPERATING INSTRUCTION
A.
DC
A.
A.
A. DC
a. Connect the black test lead to the “ COM “ jack and the red test lead to
the “ V/ Ω “ jack .
b. Press to select U , enter the DC voltage measurement.
c. Auto range by press key and manual range by press
d. Manual range ： 0.000V 6.600V range
B.
B.
B.
B. AC
Voltage
DC
Voltage
DC Voltage
Voltage Measuring
WARNING!
WARNING!
WARNING!
WARNING!
You can ’ t input the voltage which more than 660V DC, it ’ s possible to show higher voltage, but it ’ s
may destroy the inner circuit.
Pay attention not to get an electric shock when measuring high voltage.
AC
Voltage
AC
Voltage
AC Voltage
Voltage Measuring
INSTRUCTION
INSTRUCTION
INSTRUCTION
Measuring
Measuring
Measuring
00.00V 66.00V range
000.0V 660.0V range
000.0mV 660.0mV range
Measuring
Measuring
Measuring
ester
T ester
ester User
User
User ’
Manual
’
s
Manual
’ s
s Manual
Manual
WARNING!
WARNING!
WARNING!
WARNING!
You can ’ t input the voltage which more than 660V AC, it ’ s possible to show higher voltage, but it ’ s
may destroy the inner circuit.
Pay attention not to get an electric shock when measuring high voltage.
a. Connect the black test lead to the “ COM ” jack and the red test lead to the “ V/ Ω” jack.
29
29
29
29
CCTV
T
ester
User
’
s
CCTV
T
66.00V range
660.0V range
660.0mV range
ester
T ester
ester User
6.600V range
manual
manual
manual range
range
range
range )
CCTV
CCTV T
~
~
~
b. Press to select
and manual range by press
Manual range ： 0.000V
C
.
DC
Current
C
.
DC
Current
C
C .
. DC
DC Current
Current Measuring(only
WARNING!
WARNING!
WARNING!
WARNING!
Shut down the power of the tested circuit, and then connect the meter with the circuit for
measurement.
a. Connect the black test lead to the “ COM “ jack and the red test lead to
the ” mA “ jack for a maximum of 660mA current. For a maximum of
10A, move the red lead to the 10A jack.
b. Press to select A
range by press , only manual range supply.
Manual range ： 0.000mA 6.6mA range
c. Connect test leads in series with the load under measurement.
d. You can get reading from LCD.
~
U
, enter the AC voltage measurement. Auto range by press key
00.00V
000.0V
000.0mV
Measuring(only
Measuring(only
Measuring(only manual
A
,
A
,
A ,
, enter the DC current measurement. Manual
00.00mA 66.00mA range
000.0mA 660.0mA range
00.00A 10.00A range （ use 10A socket ）
User
User ’
’
s
’ s
s Manual
)
)
)
Manual
Manual
Manual
NOTE:
NOTE:
NOTE:
NOTE:
When only the figure “ OL ” is displayed, it indicates over range situation and the higher range has to
be selected.
When the value scale to be measured is unknown beforehand, set the range selector at the highest
30
30
30
30
CCTV
T
ester
User
’
s
CCTV
T
CCTV
CCTV T
position.
The maximum current of mA socket is 660mA, over-current will destroy the fuse, and will damage
the meter.
The maximum current of 10A socket is 10A, over-current will destroy the meter, and will damage
the operator.
D.
AC
Current
D.
AC
D.
D. AC
AC Current
WARNING!
WARNING!
WARNING!
WARNING!
Shut down the power of the tested circuit, and then connect the meter with the circuit for
measurement.
a. Connect the black test lead to the “ COM “ jack and the red test lead to
the ” mA “ jack for a maximum of 660mA current. For a maximum of
10A, move the red lead to the 10A jack.
Measuring
Current
Measuring
Current Measuring
Measuring (Only
(Only
(Only
(Only Manual
ester
T ester
ester User
Manual
range)
Manual
range)
Manual range)
range)
User
User ’
Manual
’
s
Manual
’ s
s Manual
Manual
b. Press to select
range by press only manual range supply.
Manual range ： 0.000mA 6.600mA range
c. Connect test leads in series with the load under measurement.
d. You can get reading from LCD.
NOTE:
NOTE:
NOTE:
NOTE:
When only the figure “ OL ” is displayed, it indicates over range situation and the higher range has to
be selected.
When the value scale to be measured is unknown beforehand, set the range selector at the highest
position.
The maximum current of mA socket is 660mA; over-current will destroy the fuse, and will damage
~
A
, enter the AC current measurement. Manual
00.00mA 66.00mA range
000.0mA 660.0mA range
00.00A 10.00A range （ use 10A socket ）
31
31
31
31
CCTV
T
ester
User
’
s
CCTV
T
CCTV
CCTV T
the meter.
The maximum current of 10A socket is 10A, over-current will destroy the meter, and will damage
the operator.
In ” AC ” mode, only can input “ AC “ , if not, will damage the meter.
E.
Resistance
E.
Resistance
E.
E. Resistance
Resistance Measuring
WARNING!
WARNING!
WARNING!
WARNING!
When measuring in-circuit resistance, be sure the circuit under test has all power removed and that all
capacitors have discharged fully.
a. Connect the black test lead to the “ COM “ jack and the red test lead to the ” V/ Ω” jack.
b. Press to select Ω , enter the Ω measurement. Auto range by press key, and manual
range by press .
c. Connect test leads across the resistance under measurement.
d. You can get reading from LCD.
NOTE:
NOTE:
NOTE:
NOTE:
When only the figure “ OL ” is displayed, it indicates over range situation and the higher range has to be
selected.
Measuring
Measuring
Measuring
Manual range ： (Connect the red lead to black leads, will display the measure range)
000.0 Ω 660 Ω range
0.000 K Ω 6.600K Ω range
00.00 K Ω 66.00K Ω range
000.0 K Ω 660.0K Ω range
0.000 M Ω 6.600M Ω range
00.00 M Ω 66.00M Ω range
ester
T ester
ester User
User
User ’
Manual
’
s
Manual
’ s
s Manual
Manual
32
32
32
32
CCTV
T
ester
User
’
s
CCTV
T
CCTV
CCTV T
F.
Continuity
F.
Continuity
F.
F. Continuity
Continuity Testing
WARNING!
WARNING!
WARNING!
WARNING!
When testing the circuit continuity, be sure that the power of the circuit has been shut down and all
capacitors have been discharged fully.
a. Connect the black test lead to the “ COM ” jack and the red test lead to the “ V/ Ω” jack.
b. Press to select , enter the continuity test.
c. Connect test leads across two point of the circuit under testing.
d. If continuity exists (i.e., resistance less than about 50 Ω ), built-in
buzzer will sound.
e. You can get reading from LCD.
G.
Diode
G.
Diode
G.
G. Diode
Diode Testing
a. Connect the black test lead to the ” COM “ jack and the red test lead to the “ V/ Ω jack ” .(the red lead
anode “ + ” )
b. Press to select , enter the diode testing.
c. Connect test red lead across to the anode, the black lead to the cathode of the diode under testing.
d. Connect test red lead across to the cathode, the black lead to the anode of the diode under testing.
E . Tested diode ， forward voltage low 30 mv ， there is sound indication ,then can finish the testing quickly
without view the screen.
F.The capacitance of a capacitor should be tested separately, should not test in the installation of circuit.
Testing
Testing
Testing
Testing
Testing
Testing
ester
T ester
ester User
User
User ’
Manual
’
s
Manual
’ s
s Manual
Manual
H.
Capacitance
H.
Capacitance
H.
H. Capacitance
Capacitance Measuring
WARNING!
WARNING!
WARNING!
WARNING!
To avoid electric shock, be sure the capacitors have been discharged fully before measuring the
capacitance of a capacitor.
Measuring
Measuring
Measuring
33
33
33
33
CCTV
T
ester
User
’
s
CCTV
T
CCTV
CCTV T
a. Connect the black test lead to the ” COM ” jack and the red test lead to the “ V/ Ω” jack.
b. Press to select , enter the capacitance measurement.
Auto range by press key , and manual range by press .
Manual range ： 0.000nF
00.00nF
000.0nF
0.000uF
00.00uF
000.0uF
0.000mF
00.00mF
c. Before connect test leads across two sides of the capacitor under measurement, be sure that the
capacitor has been discharged fully.
d. You can get reading from LCD.
Note:
Note:
Note:
Note:
a. The capacitance of a capacitor should be tested separately, should not test in
the installation of circuit.
ester
T ester
ester User
User
User ’
6.600nF range
66.00nF range
660.0nF range
6.600 μ F range
66.00 μ F range
660.0 μ F range
6.600mF range
66.00mF range
Manual
’
s
Manual
’ s
s Manual
Manual
b. To avoid electric shock, be sure the capacitors have been discharged fully before measuring the ca
pacitance of a capacitor.
c. While testing the capacitance of a capacitor to
660uF, the Max time will be 6.6 seconds, if the capacitor is leaked or damaged,
the data can ’ t be read. The tester will be normal after disconnecting the capacitor.
Manual
range
and
Auto
Manual
range
range and
and
and Auto
Manual
Manual range
Press the key to change the value, press the
to Auto measurement
Auto
Auto range
range
range
range
34
34
34
34
CCTV
T
ester
User
’
s
CCTV
T
CCTV
CCTV T
Data
hold
Data
hold
Data
Data hold
hold
Press the key to hold the data, the value is green.
Press it again to quit.
Relative
value
Relative
Relative
Relative value
Press the key , the tester Auto-save the data, the
displayed new measurement and relative value is red color.
Press it again to quit
The hold function and the relative value be combined use,
the display value is yellow
The
meter
The
⑴ The
Voltage
Resistance
mA
meter
The meter
meter protection
Voltage
Voltage
Voltage protection
You can ’ t input the voltage which more than 660V AC,
it ’ s possible to show higher voltage, but it ’ s may destroy
the inner circuit.
Resistance
Resistance
Resistance 、 Continuity
Wrong input voltage ， will Auto enter protection state , It only suitable for short and limit time work.
If the input voltage over 600V, will damage the meter.
mA
current
mA
current
mA current
current fuse
if the current over the rated range ， fuse will melt to protect the meter .Pls use the same model when
change the fuse, Pls opens the battery cover to change.
measurement
value
measurement
value measurement
measurement
protection
protection
protection
protection
protection
protection
Continuity
Continuity
Continuity 、 Diode
fuse
range
fuse
range
fuse range
range ： 250V
Diode
Diode
Diode 、 PTC
250V
250V
250V 1A
ester
T ester
ester User
PTC
component
PTC
component
PTC component
component Protection
1A
1A
1A
User
User ’
Manual
’
s
Manual
’ s
s Manual
Manual
Protection
Protection
Protection
Note:
Note:
Note:
Note: 10A socket without fuse protection, if over the current range
Wrong using the 10A socket to measure the voltage, will damage the meter.
35
35
35
35
CCTV
T
ester
User
’
s
CCTV
T
Meter
Meter
Meter （ optional
ester
T ester
ester User
optional
optional
optional ）
CCTV
CCTV T
3.3.1
7
3.3.1
3.3.1
3.3.1 7
Press twice or press and , select press to enter.
⑴ Function
⑵ Instruction
A.
A.
A.
A. Press MODE key to select “ Optical power meter ”
B.
B.
B.
B. Absolute power value measurement
Optical
7
Optical
7 Optical
Optical Power
Function
Function
Function ：
： Data hold Relative measuring
： Wavelength select : mW/dBm units select
Instruction
Instruction
Instruction ：
1) Set the wavelength via key, the default wavelength
is 1310nm.
2) Input the optical fiber to be measured, the power value is
displayed in LCD.
3) Linear and nonlinear value of the current optical-fiber power can be displayed by pressing
Power
Power
Power Meter
key to change the unit to be mW or dBm.
User
User ’
Manual
’
s
Manual
’ s
s Manual
Manual
Note
Pls
keep
the
fiber
Note
Pls
Note
Note ： Pls
Data
hold
Data
hold
Data
Data hold
hold
While testing, press to data hold, the data will not change.
It ’ s convenient to read. Press again to quit.
Relative
Relative
Relative
Relative power
measurement
measurement
measurement
measurement
keep
Pls keep
keep the
the
the
the
the special
power
value
power
value
power value
value (optical
special
special
special alcohol.
the
fiber
the fiber
fiber connector
(optical
(optical
(optical link
connector
connector
connector and
alcohol.
alcohol.
alcohol.
link
loss)
link
loss)
link loss)
loss)
and
and
and the
the
dust
the
dust
the dust
dust cap
36
36
36
36
cap
cap
cap be
be
clean,
be
clean,
be clean,
clean, and
and
and
and clean
clean
clean
clean the
the
detector
the
detector
the detector
detector with
with
with
with
CCTV
T
ester
User
’
s
CCTV
T
CCTV
CCTV T
1) Set the wavelength for measurement.
2) Measure the first optical fiber, pressing the key
under any display unit, then the current fiber power value is
stored as the base reference value.
3) Input another optical fiber to be measured, the relative power
value is displayed. The optical power meter displays the end-end loss
of the fiber under test; the unit of loss value must be dB.
Data hold and Relative measuring use together, the data is yellow while the function is effect.
ester
T ester
ester User
User
User ’
Manual
’
s
Manual
’ s
s Manual
Manual
3.3.18
3.3.18
3.3.18
3.3.18 Visual
Press to select ,then press to enter.
I nsert the fiber to the device ’ s “ VFL “ interface, default output power is 10mW and the wavelength is
650nm. Press to adjust pulse mode and stable model
3.3.1
3.3.1
3.3.1
3.3.1 9
Connect Alligator clip cable to the TDR port, and the cable must connect well before testing, or it will
influence the accuracy.
Press to select , press to enter.
9
9
9 TDR
Note
Note
Note
Note ： The
Visual
Visual
Visual Fault
TDR
TDR
TDR Tester
The
The
The testing
Fault
Fault
Fault Locator
Tester
Tester
Tester （ optional
testing
cable
testing
cable
testing cable
cable can
Locator
Locator
Locator （ optional
optional
optional
optional ）
can
’
t
be
can
’
t
be
can ’
’ t
t be
be connected
connected
connected
connected to
optional
optional
optional ）
to
any
equipment,
to
any
equipment,
to any
any equipment,
equipment, or
or
or
or it
it
it
it will
will
will
will damage
damage
damage
damage the
the
tester.
the
tester.
the tester.
tester.
37
37
37
37
CCTV
T
ester
User
’
s
CCTV
T
CCTV
CCTV T
Built-in BNC, network cable, RVV control cable, Telephone line can test. 12 groups user-defined cable
can be set.
Press to line type interface, press to choose the line type, press to save and
start testing.
Press to adjust the speed, if select the user-defined cable type, adjust the speed after the
calibration.
User-defined
User-defined
User-defined
User-defined calibration
press
press
press
press to
groups
groups
groups
groups user-defined
calibration
calibration
calibration ： Choose
to
set
to
set
to set
set the
user-defined
user-defined
user-defined can
Choose
Choose
Choose the
the
user-defined
the
user-defined
the user-defined
user-defined calibration.
can
be
set.
can
be
set.
can be
be set.
set.
ester
T ester
ester User
the
cable
cable
cable 100
100
100
100 meters
the
the cable
calibration.
calibration.
calibration. Press
Manual
User
’
s
Manual
User ’
’ s
s Manual
Manual
meters
to
meters
meters to
Press
Press
Press to
200
to
200
to 200
200 meters
meters
(more
meters
(more
meters (more
(more than
to
select
to
select
to select
select user
user
user
user 1
than
than
than 50
1
to
1
to
1 to
to calibrate,
50
meters)
50
meters)
50 meters)
meters)
calibrate,
calibrate,
calibrate, 12
12
12
12
Press to “ Adjust ” , press to cable type, press to choose the cable style, press
to “ Speed ” and press to adjust. While display length is the same as the actual
length, press to save. It can be used for the same cable after the calibration.
Application
Application
Application
Application
The
disconnection
The
disconnection
The
The disconnection
disconnection and
repair
repair
repair
repair the
connected
connected
connected
connected etc
only.
only.
only.
only.
the
faulty
the
faulty
the faulty
faulty cable.
Note
Note
Note
Note ： The
etc
to
etc
to
etc to
to cause
：
and
cable.
cable.
cable.
The
The
The TDR
cause
cause
cause the
short
and
short
and short
short circuit
TDR
reflect
TDR
reflect
TDR reflect
reflect signal
the
the
the different
circuit
circuit
circuit display
signal
signal
signal could
different
different
different TDR
display
in
the
display
display in
could
could
could be
TDR
TDR
TDR measurement.
tester,
in
the
tester,
in the
the tester,
tester, it
be
affected
be
affected
be affected
affected by
measurement.
measurement.
measurement. The
38
38
38
38
it
is
more
it
is
more
it is
is more
more convenient
by
the
cable
by
the
cable
by the
the cable
cable quality/
The
TDR
The
The TDR
measurement
TDR
measurement
TDR measurement
measurement is
convenient
convenient
convenient and
quality/
quality/
quality/ cable
and
efficient
and
efficient
and efficient
efficient to
cable
’
s
cable
’
s
cable ’
’ s
s not
is
for
is
for
is for
for reference
not
not
not well
reference
reference
reference
well
well
well
to
to
to
CCTV
T
ester
User
’
s
CCTV
T
CCTV
CCTV T
3.3.
20
Data
3.3.
20
3.3.
3.3. 20
20 Data
Press to select , press to enter.
Press to choose the baud rate of RS485/RS232; it must be the same as the DVR or the
Control keyboard.
The DVR or Control keyboard send the code to the tester, if it can be read, the protocol will shown on
the upper right, like Pelco D, if not, like P:---
Press to empty while the tester receives the code.
Though the RS485 port, display the PTZ control code of the multifunctional keyboard or the DVR.
Controller can check the status of the RS485 transmission through the code on the display. (The RS485
communication rate must be the same.)
monitor
Data
monitor
Data monitor
monitor
ester
T ester
ester User
User
User ’
Manual
’
s
Manual
’ s
s Manual
Manual
Application
Application
Application
Application ： Check the RS485 communication states of the video optical transmitter
whether normal. Engineer can analyze the protocol and check the data through the
displayed code.
3.3.2
1
Time
3.3.2
1
3.3.2
3.3.2 1
1 Time
Press to menu , press to enter.
setting
Time
setting
Time setting
setting
39
39
39
39
CCTV
T
ester
User
’
s
CCTV
T
CCTV
CCTV T
Note
Press
Note
Press
Note
Note ： Press
Press to set the parameter of the time, press to save. Users need to set
the time first, as the time of the photograph and video record is the same as the Time setting.
3.
3
.
2
2
Devi
ce
3.
3
.
2
2
3.
3. 3
Press to menu , press to enter.
Press or to choose the item, press to adjust, press to save, press
to quit.
Auto power off: Setting the time of auto shut-down.(Disable,5,10, … ,60)
Disable: Disable the “ Auto power off ” function. 5 means the CCTV will power off after 5 minutes
when there is no any operation.
Keypad tone: Open or close the beep of pressing keypad.
Language
Language
Language
Language ： ENGLISH/
Brightness: Setting the brightness of OSD menu and background.(0~7)
Address search: off / on Open or close the PTZ address search Menu.
Devi
3 .
. 2
2 2
2 Devi
Devi ce
ENGLISH/
ENGLISH/
ENGLISH/ CHINESE
ce
ce setting
setting
setting
setting
CHINESE
CHINESE
CHINESE and
ester
T ester
ester User
and
other
and
other
and other
other languages
languages
languages
languages
User
User ’
Manual
’
s
Manual
’ s
s Manual
Manual
Restore
factory
Restore
factory
Restore
Restore factory
factory setting:
F1
user-defined
F1
user-defined
F1
F1 user-defined
user-defined keyboard
press
press
press
press to
F2
F2
F2
F2 user-defined
setting
setting
setting
setting ”
to
to
to save.
user-defined
user-defined
user-defined shortcut
”
.
”
.
” .
.
setting:
restore
setting:
restore
setting: restore
restore the
keyboard
keyboard
keyboard shortcuts:
save.
save.
save. The
shortcut
shortcut
shortcut key
shortcuts:
shortcuts:
shortcuts: Users
The
default
The
default
The default
default value
key
key
key is
is
is
is t
the
the
the data
value
value
value is
t
he
same
t
he
same
t he
he same
same setting
data
data
data of
Users
Users
Users can
is
is
is “
of
the
factory.
of
the
factory.
of the
the factory.
factory.
can
set
can
set
can set
set the
“
PTZ
controller
“
PTZ
controller
“ PTZ
PTZ controller
controller ”
setting
of
setting
of
setting of
of the
40
40
40
40
the
function
the
function
the function
function as
the
F1
the
F1
the F1
F1 shortcuts
as
you
as
you
as you
you like,
”
.
”
.
” .
.
shortcuts
shortcuts
shortcuts keys
like,
like,
like, press
keys
keys
keys .
press
press
press t
.
The
default
.
The
default
. The
The default
default is
is
is
is “
t
o
t
o
t o
o select,
“
Device
“
Device
“ Device
Device
select,
select,
select,
CCTV
T
ester
User
’
s
CCTV
T
CCTV
CCTV T
3.3.2
3
3.3.2
3.3.2
3.3.2 3
All the photograph files or video record can be uploaded to computer, it ’ s convenient to check.
3.4
3.4
3.4
3.4 DC12V
Power the camera with DC12V (1A) power output from the tester. It is helpful for demo and testing
where there is no power supply available.
USB
3
USB
3 USB
USB
DC12V
DC12V
DC12V 1A
1A
power
1A
power
1A power
power output
ester
T ester
ester User
output
output
output
User
User ’
Manual
’
s
Manual
’ s
s Manual
Manual
Notice
Notice
Notice
Notice
a. Don ’ t input any power into the “ DC12/1A OUTPUT ” port of the CCTV tester to avoid destroy.
b. Don ’ t output this DC12V/1A power to the power input port of the CCTV tester to avoid destroy.
c. When the requirement of the camera is higher than 1A, the CCTV tester will enter protection
mode. Disconnect all the connections of the CCTV tester and then connect the CCTV tester with
power adaptor to resume the CCTV tester.
d. Make sure the the tester is full charged or more than 3 bars, or it will be short circuit.
41
41
41
41
CCTV
T
ester
User
’
s
CCTV
T
CCTV
CCTV T
3.5
Audio
3.5
Audio
3.5
3.5 Audio
Audio input
Test the audio input from pickup devices. Connect the tester and pickup device with the audio cable.
3.6
LED
3.6
LED
3.6
3.6 LED
LED lamp
With the LED lamp can work in the evening or in the dark.
Turn on the tester, press for several seconds, and the LED lamp turn on, press , and turn it
off.
Note:
Note:
Note:
Note: Laser is harmful, so especially, you must protect your eyes. When the LD working, please
input
input
input test
lamp
lamp
lamp
test
test
test
ester
T ester
ester User
User
User ’
Manual
’
s
Manual
’ s
s Manual
Manual
don ’ t let your eyes exposure to laser.
4
Specifications
4
Specifications
4
4 、 Specifications
Specifications
4.1
General
4.1
General
4.1
4.1 General
General Specifications
Video
Test
Video
Test
Video
Video Test
Test
Signal mode NTSC/PAL (Auto adapt)
Display 3.5 inch digital TFT-LCD ,480 （ RGB ） x 320 resolution
LCD adjustment Brightness, Contrast, Saturation adjustable
Video IN/OUT 1 channel BNC Input & 1 channel Output
Video Output Mode 1.0 Vp-p
Specifications
Specifications
Specifications
42
42
42
42
CCTV
T
ester
User
’
s
CCTV
T
CCTV
CCTV T
Video
Level
Video
Video
Video Level
Level test Video signals measured in IRE or mV
PTZ
PTZ
PTZ
PTZ controller
Communication Support RS232 and RS485
PTZ Protocol
Baud Rate 600 ， 1200 ， 2400 ， 4800 ， 9600 ， 19200,57600,115200bps
Video
Video
Video
Video Signal
Color bar generator
UTP
UTP
UTP
UTP C
UTP cable test
DC12V
DC12V
DC12V
DC12V 1A
DC12V power output Output DC12V1A power for camera
Audio
Audio
Audio
Audio input
Audio input test test the pickup and other audio equipments on the front-end
RS485
RS485
RS485
RS485 data
Data Monitor Captures and analyzes the command data from controlling device
test
Level
test
Level test
test
controller
controller
controller
Signal
Generation
Signal
Generation
Signal Generation
Generation
C
able
tester
C
able
tester
C able
able tester
tester
1A
power
1A
power
1A power
power output
input
test
input
test
input test
test
data
analysis
data
analysis
data analysis
analysis
Compatible with more than 30 protocols such as PELCO-D/P, Samsung,
Panasonic, Lilin, Yaan, etc.
Output one channel PAL/NTSC color bar video signal for testing monitor or
video cable.(red, green ,blue, white and black color )
Test UTP cable connection status and display in the screen. Read the number of
the test box.
output
output
output
ester
T ester
ester User
User
User ’
Manual
’
s
Manual
’ s
s Manual
Manual
10x
Zoom
10x
10x
10x Zoom
Photograph
Photograph
Photograph
Photograph 、 Video
Photograph snapshot and save the current image as JPG file
Video record Video record and storage the file
Image
Zoom
Image
Zoom Image
Image
Image 10x zoom 10x zoom image display and video out
Video
record,
Record
Video
record,
Video record,
record, Record
playback
Record
playback
Record playback
playback
43
43
43
43
CCTV
T
ester
User
’
s
CCTV
T
CCTV
CCTV T
Record playback To view the storage file in the SD card
Port
flicker
Port
flicker
Port
Port flicker
flicker
Port flicker Find the connected POE port quickly.
IP
scan
Link
IP
scan
IP
IP scan
scan 、 Link
IP scan
Link monitor Check the IP address whether is occupied
PING testing
Cable
Cable
Cable
Cable scan
Cable scan Search the cable by the audio signal
PoE
tester
PoE
tester
PoE
PoE tester
tester
PoE tester Display the power supply voltage and cable connection states
Digital
Digital
Digital
Digital M
AC/DC Voltage 0-660V auto/manual range, the min resolution is 0.1mV
AC/DC current 660.0uA , 6.600mA, 66.00mA , 660.0mA, 10.00A
Resistance 660.0 Ω , 6.600k Ω , 66.00k Ω , 660.0k Ω , 6.600M Ω , 66.00M Ω
Capacitance 6.6nf ～ 66000uF ， the min resolution is 1pf
Diode 0 ～ 2V forward voltage, the min resolution is 1mV
Data hold Hold and display the measure d value
Relative measurement Display the relative power value
Continuity testing Built-in buzzer will sound, if resistance is lower than 50 Ω
Testing speed 3 times/ seconds
Data range -6600 ～ +6600
Optical
Optical
Optical
Optical power
Calibrated
Wavelength(nm)
Power range(dBm) -70 ～ +10dBm
Sensitivity(nW) 0.001nW
Link
Link monitor
scan
scan
scan
M
ultimeter
M
ultimeter
M ultimeter
ultimeter
power
power
power meter
monitor
monitor
monitor 、 PING
meter
meter
meter
PING
PING
PING test
Find out the connected IP camera or the other network equipment IP address quickly.
Test IP camera or Ethernet port of the other network equipment whether work
normally, and check the IP address
850/1300/1310/1490/1550/1625nm
ester
T ester
ester User
test
test
test
User
User ’
Manual
’
s
Manual
’ s
s Manual
Manual
44
44
44
44
CCTV
T
ester
User
’
s
CCTV
T
CCTV
CCTV T
Connector type FC/PC
Data hold Hold and display the measured value
Relative measurement Display the relative power value
Visual
fault
fault
fault locator
Tester
Tester
Tester
locator
locator
locator
Visual
Visual
Visual fault
Visual fault locator Test fiber ’ s bending and breakage ( SM and MM fiber)
TDR
TDR
TDR
TDR Tester
TDR Tester breakpoint and short circuit measurement(BNC cable, telephone cable)
POWER
POWER
POWER
POWER
Power Adapter DC 5V （ 1.5A ）
Battery Built-in 3.7V Lithium polymer battery ,3000mAh
Rechargeable After charging 3-4 hour, working time lasts 11 hours
Low Consumption Energy saving technology, the battery icon real-time display
Parameter
Parameter
Parameter
Parameter
Operat ion setting English/Chinese and other languages OSD menu
Auto off 5-60 (mins)
Keytone On/Off
General
General
General
General
Working Temperature -10 ℃ ～ +50 ℃
Working Humidity 30% ～ 90%
Dimension /Weight 194mm x 112mm x 48mm / 540g
ester
T ester
ester User
User
User ’
Manual
’
s
Manual
’ s
s Manual
Manual
4.2
Multimeter
4.2
Multimeter
4.2
4.2 Multimeter
Multimeter specifications:
Counts ： -6600 ～ +6600
Conversion rate: 3 times/s
Current modes for clamp meter with ZERO function
Isolation: the Multimeter connector must be isolated with the other connector.
specifications:
specifications:
specifications:
45
45
45
45
CCTV
T
ester
User
’
s
CCTV
T
CCTV
CCTV T
DC
Voltage
DC
Voltage
DC
DC Voltage
Voltage
Range
Range
Range
Range Accuracy
660mV (Manual range)
6.600V 1mV
66.00V 10mV
660.0V 100mV
AC
Voltage
AC
Voltage
AC
AC Voltage
Voltage
Range
Range
Range
Range Accuracy
660.0mV (Manual range) ± （ 1.5%+6 ） 0.1mV
6.600V
66.00V 10mV
660.0V 100mV
DC
Current
DC
Current
DC
DC Current
Current
Range
Range
Range
Range Accuracy
6.600mA
66.00mA 10uA
660.0mA 100uA
10.00A ± （ 1%+5 ） 10mA
ester
T ester
ester User
Accuracy
Accuracy
Accuracy Resolution
± （ 0.5%+3 ）
Manual
User
’
s
Manual
User ’
’ s
s Manual
Manual
Accuracy
Accuracy
Accuracy Resolution
± （ 0.3%+4 ）
Accuracy
Accuracy
Accuracy Resolution
± （ 0.8%+6 ）
0.1mV
1mV
Resolution
Resolution
Resolution
Resolution
Resolution
Resolution
Resolution
Resolution
Resolution
1uA
AC
Current
AC
Current
AC
AC Current
Current
Range
Range
Range
Range Accuracy
6.600mA
66.00mA 10uA
660.0mA 100uA
Accuracy
Accuracy
Accuracy Resolution
± （ 0.5%+3 ）
46
46
46
46
Resolution
Resolution
Resolution
1uA
CCTV
T
ester
User
’
s
CCTV
T
CCTV
CCTV T
10.00A ± （ 1%+5 ） 10mA
Resistance
Resistance
Resistance
Resistance
Range
Range
Range
Range Accuracy
660.0 Ω
6.600K Ω
66.00K Ω 10 Ω
660.0K Ω 100 Ω
6.600M Ω 1K Ω
66M Ω ± （ 1.2%+5 ） 10K Ω
Continuity
Continuity
Continuity
Continuity
Range
Range
Range
Range Resolution
660.0 Ω 0.1 Ω The measurement value less 30 Ω± 3 Ω ,the tester will
Resolution
Resolution
Resolution Function
ester
T ester
ester User
Accuracy
Accuracy
Accuracy Resolution
± （ 0.8%+5 ）
± （ 0.8%+2 ）
sound
User
User ’
Manual
’
s
Manual
’ s
s Manual
Manual
Function
Function
Function
Resolution
Resolution
Resolution
0.1 Ω
1 Ω
Diode
Diode
Diode
Diode
2.0V 1mV
Capacitance
Capacitance
Capacitance
Capacitance
Range
Range
Range
Range Resolution
Range
Range
Range
Range Accuracy
Resolution
Resolution
Resolution Function
Function
Function
Function
Schottky diode ： 0.15~0.25V
rectifier diode ： 0.6~1.0V
triode PN junction:0.5~0.8V
Accuracy
Accuracy
Accuracy Resolution
47
47
47
47
Resolution
Resolution
Resolution
CCTV
CCTV
CCTV
CCTV T
T
ester
T
ester
T ester
ester User
User
User
User ’
’
s
Manual
’
s
Manual
’ s
s Manual
Manual
6.600nF
66.00nF
660.0nF 100pF
6.600 μ F 1nF
66.00 μ F 10nF
660.0 μ F
6.600mF 1 μ F
66.00mF 10 μ F
4.3
Optical
4.3
Optical
4.3
4.3 Optical
Optical power
Measure Range(dBm)
Wavelength(nm)
Detector InGaAs
Uncertainly
Display Resolution
power
power
power meter
± （ 0.5%+20 ）
± （ 3.5%+8 ）
± （ 5%+8 ）
meter
meter
meter specifications
specifications
specifications
specifications
850nm 、 1300nm 、 1310nm 、 1490nm 、 1550nm 、 1625nm
＜ ± 3%dB(-10dBm ， 22 ℃ )
＜ ± 5%dB(full range ， 22 ℃ )
Linear ： 0.1% ; Nonlinear ： 0.01dBm
1pF
10pF
100nF
-70 〜 +10dBm
Operating Temperature( ℃ ) -10 ～ +50
Storage Temperature ( ℃ ) -20 ～ +70
Connector type FC/PC
4.4
Optional
4.4
Optional
4.4
4.4 Optional
Optional models
function model A B C D E F
3.5 HVGA LCD
Image enl arge （ 1-10 times ）
models
models
models
G
H I
48
48
48
48
CCTV
T
ester
User
’
s
CCTV
T
CCTV
CCTV T
photograph
Video record
Record playback
SD card
Color - bar generator
Video signal level test
Protocol capture and
display
PTZ address search
DC 12V /1A power output
Audio test
LED Lamp
PING test
Port flicker
POE teste r
Link monitor
IP address scan
UTP cable tester
Wire tracker
Digital multimeter
Optical power meter
Visual fault locator
TDR Tester A+T B+T C+T D+T E+T F+T G +T H+T I+T
ester
T ester
ester User
User
User ’
Manual
’
s
Manual
’ s
s Manual
Manual
A: Base Model A+T: Base Model+TDR
B: Add Wire tracker B+T: Add Wire tracker+TDR
C: Add Wire tracker +DMM C+T: Add Wire tracker +DMM+TDR
49
49
49
49
CCTV
T
ester
User
’
s
CCTV
T
and
and
and any
please
please
please feel
ester
T ester
ester User
any
change
any
change
any change
change of
feel
free
feel
free
feel free
free to
CCTV
CCTV T
D: Add OPM D+T: Add OPM+TDR
E: Add Wire tracker +OPM E+T: Add Wire tracker +OPM+TDR
F: Add Wire tracker +OPM+DMM F+T: Add Wire tracker +OPM+DMM+TDR
G: Add RLS G+T: Add RLS+TDR
H: Add wire tracker +RLS H+T: Add wire tracker +RLS+TDR
I: Add wire tracker +RLS +DMM I+T: Add wire tracker +RLS +DMM+TDR
The
data
above
is
only
for
The
data
The
The data
data above
more
detailed
more
detailed
more
more detailed
detailed technical
company.
company.
company.
company.
above
is
above is
is only
technical
technical
technical inquiries,
only
only for
for
for reference
reference
reference
reference and
inquiries,
inquiries,
inquiries, please
User
User ’
to
to
to call
Manual
’
s
Manual
’ s
s Manual
Manual
of
them
will
of
them
will
of them
them will
will not
call
the
Technical
call
the
Technical
call the
the Technical
Technical Department
not
not
not be
be
informed
be
informed
be informed
informed in
Department
Department
Department of
in
in
in advance.
of
of
of our
advance.
advance.
advance. For
our
our
our
For
For
For
50
50
50
50
Loading...