How it Works
XtendLan
Loading...
TC-261H
User Manual
15 pgs514.22 Kb0

XtendLan TC-261, TC-261H, RB-261, RB-262 User Manual

Download
Fanless VESA Mini PC
TC-261 200MHz Mini PC, 1x LAN TC-261H 200MHz Mini PC, 1x LAN, HDD mount RB-261 200MHz Mini PC, 1x LAN, miniPCI RB-262 200MHz Mini PC, 1x LAN, miniPCI,2xCOM
User’s Manual
SAFETY INFORMATION
WARNING
¾ Do not expose your computer to rain or moisture, in order to prevent shock and fire
hazard.
¾ Never install your computer in wet locations. ¾ Do not open the cabinet to avoid electrical shock. Refer to your nearest dealer for
qualified personnel servicing.
¾ Never touch un-insulated terminals or wire unless your power adaptor and display
monitor are disconnected.
¾ Locate your computer as close as possible to the socket outline for easy access and to
avoid force caused by entangling of your arms with surrounding cables from the computer.
¾ When using Mini PC, avoid using or installing the modem to the serial port during a
storm or a lightning.
¾ Do not use the modem or a telephone to report a gas leak in the vicinity of the leak.
REGULATORY
FCC CLASS A NOTE
This equipment has been tested and found to comply with the limits for a Class A digital device, purs uant to Part 15 of the FCC Rules. These limits are designed to provide r easonable protection against harmful interference when the equipment is operated in a commercial envi ronment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference in which case the user will be required to correct the interference at his own expense. Testing was done with shielded cables. T herefore, in order to comply with the FCC regulat ions, you must use shielded cables with your installation.
WARNING
This product Complies with EN55022 Class A. In a domes tic enviro nment this prod uct may caus e radio interference in which case the user may be required to take adequate measures.
Changes or modifications to this unit not expres sly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC r ules. Operation is s ubject to the f ollowing two cond itions: (1) this device may not cause harmful interference, and (2) t his device must accept any interference received, including interference that may cause undesired operation.
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in the interference - causing equipment standard entit led “Digital Apparatus ”, ICES-003 of the Department of Communications.
MANUFACTURER’S DECLARATION OF CONFORMITY
This equipment has been tested and found to co mply with the requirements of European Community Council Directives 89/336/EEC and 73/23/EEC relating to electromagnetic compatibility and product safety respectively.
ATTENTION
This product has been designed an d certified to comply with certain r egulatory requirements pertaini ng to Information Technology Equipment. This product has not been design ed for use as a medical d evice . Without limitation of the foregoing, this product is not intended and has not been certified for use in a hospital or clinical environment to di agnose, treat, or mon itor patients under medical superv ision, and is not intended and has not been certified to make physical or electrical contact with patients, nor to transfer energy to or from patients and/or to detect such energy transfer to or from patients.
PREFACE
TC-261/TC-261H/RB-261/RB-262 : MINIPC
VESA COMPUTER
Revolutionary device that is especially designed for limited physical space and temperature concerns. No matter you are in a jammed office, a crowded place, or public transportation, it can be easily integrated with a VESA LCD to bring you VESA PC access at any time. It can attach to any VESA mounting fixture, allowing it to be securely mounted onto desks, walls, or buildings, and thereby optimizes your work area. It can also attach directly to any size LCD for a mobile system for the use at trade shows, presentations, promotions, etc. Unlike traditional portable laptop design, the VESA PC can be used with a large size LCD. Furthermore, with FANLESS design is ideal to be used in the environment where temperature demand is critical. So, if you are looking for a device that is able to provide you with more mobility & space but at the same time uses less power consumption, then this will be surely meet your need. The VESA® FDMI™ Standard defines mounting interfaces, hole patterns and associated cable/power supply locations for LCD monitors, plasma displays and other flat panel devices. Device is designed to fit this standard to make monitor attachment quick and easy.
Photo of mounted mini PC on LCD panel display.
SPECIFICATION
CPU Onboard processor x86, SoC, Fanless BIOS AMI BIOS, Quick Boot Chipset SiS 6127 System Memory Onboard 128MB SDRAM
LAN 1x Fast Ethernet RJ-45 Realtek 8100B Remote Boot ROM built-in boot ROM function, support PXE boot and Wake-up on LAN
MiniPCI none CF CompactFlash Type I / II IDE 1 x EIDE (UltraDMA 100) , 44Pin, 2.0 mm Box Header
HDD no space Mouse, Keyboard 1 x PS/2 K/B, 1 x PS/2 Mouse
COM ­USB 3 x USB 1.1 ports (two on front panel) Display Chipset Integrated in SoC, AGP 4X, 128-Bit 2D Engine, 8MB shared RAM Resolution 1280 x 1024 @32 bpp (85Hz) Audio AC97 2.1 (Codec), H/W DirectSoundTM accelerator, Audio Interface Line out, Microphone in
Supported OS Windows XP Embedded, Windows CE.NET, Linux
Mechanical & Environment
Power Requirement +5V @ 3A (5 ~ 5.25V) Operating Temperature 0 ~ 60 C (-4 – 140 F) Operating Humidity 0% - 90% relative humidity, non-condensing Size (W x H x D) 115 x 115 x 135 mm Weight 505g
TC-261 TC-261H RB-261 RB-262
1x Mini-PCI connector, port for
antenna connector
2,5" HDD
mountable
no space no space
2x RS-232, 9
pin
OVERVIEW
Front Panel
Power LED
The power LED lights up, when system
Is turn on.
HDD LED
The HDD LED flashes when the system is working. Please do not turn off the system when HDD start running
Power Switch
Depress switch to turn on & turn off the systems.
CF Slot
For connection to Device with CF Card and Micro Driver.
Audio Line Out
Audio Mic InPower Switch
USB port
For connection to devices with USB interface (keyboard, mouse, HDD, CD­ROM, Memory Stick, etc.)
Back Panel
Power switch
DC Power Jack (3-pin) PS/2 Keyboard & Mouse (6-pin) VGA port RJ-45 LAN Jack
Serial port (RB-262)
USB port
Wireless antenna connector (position on RB-26x)
PERIPHERALS
ONNECTING THE POWER ADAPTOR
C
Power Adaptor
To use your computer immediately, take and use the supplied AC adapter as a power source. See the left diagram for visual connection.
Connect the DC power jack of the power adaptor to the DC Input jack.
CONNECTING THE MONITOR
Turning ON Your Computer
Press the power button as indicated on the figure on your left-side, the system will start automatically.
VGA Connection
Depending on your choice of viewing, select a conventional CRT or the LCD VGA monitor.
Make your connection by following the reference diagram from the VGA cable of your cable to the 15-pin D-
Sub VGA port.
PERIPHERALS
ONNECTING THE USB
C
USB port are two in front & at the back of the cabinet.
ONNECTING THE KEYBOARD AND MOUSE
C
USB Port
The second USB port is available for connection to USB devices.
Speaker/Earphone
Supports Input/Output device for speaker and Microphone
Connecting to LAN
There is an available RJ-45 LAN jack for connection to the hub of your intranet; and via your server for internet service (see diagram for RJ­45 LAN jack).
The PS/2 Port is available for connect Keyboard or Mouse. Use supplied octopus to connect both into one port.
ONNECTING SERIAL PORT
C
Serial Port The serial port is usually connected to a
serial device like mem. Serial ports available on RB-262.
BIOS
RECONFIGURING
1 Take note that AMI BIOS is used in the device. To reconfigure the computer, depress or hit the <Del> key to enter your BIOS setup main menu. 2 Select from the menu, the desired setup for change. 3 Press <Esc> to go back to main menu. 4 Move your cursor to “Save Settings and Exit”, press “Y” to save the changes that you just made. Device will restart accordingly to your new setup.
ONBOARD CONNECTORS SUMMARY
SUMMARY TABLE FOR CPU BOARD
Nbr Description Type of Connections Pin nbrs.
J1 VGA Connector D-Sub Connector 8-pin J2 Power Button Power Button J3 USB (Back) USB Connector 8-pin J4 PS/2 keyboard or Mouse Mini DIN Connector 6-pin J5 RST (Reset) Hear 2x1 2.0mm 2-pin J6, J7 USB (Front) USB Connector 8-pin J8 LAN RJ-45 8-pin J9 Line Out Audio Jack J10 Mic In Audio Jack J11 IDE connector Box Header 22x2 2.0mm 44-pin J12 CF Device Jumper Close : Master 2-pin J14 DC 5V Input Mini-Din Connector 3-pin J16,1J7: COM Port Box Header 5x2 2.0mm 10-pin J18: Mini PCI Mini PCI socket 124-pin
APPENDIX
PIN ASSIGNMENTS
J4:KBD(PS/2Keyboard & Mouse) – 6-pin Mini-Din Connector
Pin # Signal Name
1 KBCLK 2 PMCLK 3 GND 4 KBDAT 5 PMDAT 6 SB5V
J8: RJ-45 LAN– 12-pin RJ45 Connector
Pin
SignalName Pin
#
1 FTXD+ 2 FTXD­3 FRXIN+ 4 NC 5 NC 6 FRXIN­7 NC 8 NC
SignalName
#
J2: Power Sw – Push Button Switch
Pin # Status
| ON
O OFF
J14: DC-IN 5V – 3-pin MINI-DIN Lock Pin Socket
Pin #
1 VCC
Signal Name
2 GND
3 NC
J3,J6,J7: USB (USB1x90
Type)
o
)– 4-pin USB Type 1 Connector (Vertical
Pin # Signal Name
1 VCC 2 USB0­3 USB0+ 4 GND 5 GGND
6 GGND
J1: VGA – 15-pin Dsub Connector
SignalName
Pin
#
1 MR 6 GND 11 NC 2 MG 7 GND 12 VCC 3 MB 8 GND 13 HYSYNC 4 NC 9 NC 14 VSYNC 5 GND 10 GND 15 VCC
Pin
#
SignalName
Pin
#
J10: MIC_IN – 5-pin RCA Phone Jack device
Pin #
SignalName
1 GND 2 AUD MIC 3 GND 4 GND 5 REF
SignalName
J9: Line-out – 5-pin Phone Jack
Pin #
SignalName
1 GND 2 LOUT L 3 NC 4 NC 5 LOUT R
J16, J17: COM1 - 9-pin Dsub Connector
SignalName
Pin
#
1 DCD1 2 RXD1 3 TXD1 4 DTR1 5 GND 6 DSR1 7 RTS1 8 CTS1 9 RI1
Pin
#
Action status
SignalName
LEDS: POWER ON/OFF & HDD R/W
LED Color
Green Red
Flashes
State
Power On HDD R/W
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use