Before using SuperIPCam, please refer to specific manual for detailed instructions
in CD. The IPCamera belongs to Q series IPCamera. This text will tell you how to
use the SuperIPCam to watch its video.
二、 Connection to Network and Configuration
Connection of IPCamera and Network: Before using SuperIPCam, connect
IPCamera to net. You can connect the IP camera into LAN, or connect into LAN then
to the internet by ADSL Modem. Please refer to the chart above.
Note: Connect IPCamera to the internet strictly according the chart above. If the net
is small, the switch can be cancelled. If connect IPCamera into the LAN through
multi-layer router, then connect the LAN to the internet, IPCamera can’t be visited
from internet.
Configuration of IPCamera: In order that PC2 and PC3 can visit IPCamera, need to
set the IP Address and port of the IPCamera in LAN, and do mapping on the router
according to the IP Address and port.
Note: For more information, Please refer the specific manual.
三、 The Installation of software SuperIPCam
Double click the SuperIPCam icon, choose installation language, English or
Chinese.
Click “OK”, follow instructions to finish the installation.
Run this software, you will see a window as below.
四、 Add an IPCamera
Right-click the mouse in the area showed above, a dialogue box will come up as
below.
Choose Q serial, click “OK”, the IPCamera setting page will come up as below.
If select IP/URL mode, input the IP address or the URL of the IPCamera (Note:
Before inputting URL, make sure the IPCamera has accessed to the Internet, and
set the right third party DDNS in IPCamera). Fill in username and password for
visiting IPCamera, see the above picture (Note, The username and password have
been set in the QTools in the area of Authorization Login).
You can also set other functions like “Alarm”, “Record” For Record, MPEG-4 format
is recommended, it supports long time recording and saves space. Due to the Q
serial can’t support moving detection, SuperIPCam can fulfill this function, but
need to select “Enable Motion Detection on Client” on Alarm setting page. See
below:
If selecting “Serial Number mode”, just input the serial Number which is assigned
by the manufacturer (Note: make sure the IPCamera has accessed to the internet,
Serial Number and URL were filled in the IPCamera, users can see the Serial
Number by QTools or the label on the IPCamera). See below.
Note: “TCP mode for getting data”. If not Checked, when more than 1 user is
visiting the IPCamera simultaneously, User end might request data from other
users so as to reduce the work load of the IPCamera. But this might make the data
stream not stable. Users make their choice.
Finish setup, click “OK”, The IPCamera will show up in the software. Double click
IPCamera to start visiting.
五、 Operation of the active window
Click one of the windows to make it active
Right click within the window, an operation menu will come up. Or click one of the
three buttons at the lower right corner to setup snapshot, alarm, or video record.
Remote control the Pan/Tilt to move the IPCamera UP, DOWN, RIGHT, LEFT, or
make it Auto Scan. Please refer to the below picture.
(Note: If the Equipment do not support Pan/Tilt, the buttons are useless)
For Q series IPCamera, the buttons showed below is not available, please ignore it.
The 3 buttons showed above are shortcut operations to Start, Quit, and Setup.
六、 Multi View
Choose multi view style according to your needs. For example: 1、4、9、15、25、
64 frames etc. Turn the page if viewing too many IPCamera.
七、 System Operation
The pictures showed above is System Operation window, click “start all”, all
IPCameras will start to work, click “Stop All’, all IPCameras will stop.
1. View History Record
Click “Records”, a dialogue box will come up, then users can view the history
records
There are two methods of Recording, “Planned Recording” and “Alarm Triggered
Recording”, Setup to Alarm and Record function accordingly.
In this dialogue box, Users can also review the recorded video. The video is
recorded in the standard coding of MPEG4 or MJPEG, Users can play it through the
normal media players.
2. System Setting
Click “System Setting”, a dialogue box will come up, setup the User-end software.
ü In the “Storage” menu, Click “add” or “Delete”, choose save path for recording.
Set “save days”, Expired record will be automatically deleted to save storage
space; Set “Recording the file’s length”, it will record block after block within
default time span. Keep files in a proper size to make index convenient.
ü In the “Display” menu, choose to display “Equipment Name” or “Time” on the
window or not.
ü In the “Alarm” menu, need to select “send alarm information to the port of TCP
and UDP 30000” at User’s end. It is effective by Q Serial Equipment.
ü In the “Auto run” menu, choose whether to run the user-end software
automatically and connect all the monitoring IPCameras.
ü In the ‘Others” menu, choose to set DDNS address (Default address:
server.nwsvr.com, please don’t change). In the multi-view mode, Users can set
automatic page-turning intervals”. Users can also choose “Cache mode” to
improve video stability.
3. Others
Click “Other” at lower right corner, Users can view Equipment List, manage Log
and Operator. In the “ About” menu, Users can check software version number and
New version availability to download.
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.